Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
209 40025 Sockethead Capscrew - Rear Flange
320 40062 Knob - Red round
306 40086 Rivet for Decal
237 40001 Capscrew - Gear Box
236 40038 Hexhead Cap Screw - Bearing Cap
220 40009 Set Screw - Pulley
213 40072 Set Screw - Lock Rod
1185 42043 Plate Switch ON/Off
1574 40055 Washer, Motor Mount
1680 40064 Set Screw, Guide Bar
1926 42049 Lock Washer- Ground Wire
2045 42034 Large Spring for Rubber Boot
2165 40052 1 H.P. Motor (motor only)216501 40052A 1 H.P. Motor and
Motor Mount Bracket(2165 and 3009)
2309 42052 Nut, Handwheel
311 42076 Ball - Drum Feed Lead Screw
Page 1
283 40056 Lock Washer - Motor Mount 2064 40010 Spring, Crossfeed2064-30 40010-30 Spring, Crossfeed (30 pack)
Replacement PartsAmmco Type
Brake Lathe
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
3036 42077 Roller, Drum Feed
3031 42007 Stud, Boring Bar Short
3031-1 40006 Stud, Boring Bar Long
3032 40111 Shim, Rear Flange
3033 40030 Thrust Washer, Spindle
3034 4303 Rubber Boot Ring
3035 40059 Pin, Eccentric Belt Release
3026 42022 Handwheel Handle
3024 42030 Small V-Belt Drive Pulley
3023 40047 Motor Mount Shaft
3010 40036 Bearing Cap Seal
3015 40058 Lever, Belt Tension
3017 40004 Clamp, Boring Bar Upper
3009 40053 Motor Mount Bracket
2364 40050 Wave Washer, Motor mount
3029 42009 Clamp Nut (Old Style)
Page 2
3022 40144 Wrench, Large
2500 40156 Bench
Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
3079 42047 Strap, Electrical Panel
3084 42024 Knurled Knob
3085-R 42035 Rubber Spindle Boot
3086 42027 Lead Screw Boot, Cloth
3087 42026 Crossfeed Boot, Cloth For 3000,4000,4100,7000,7500 and 7700lathes
3078 42082 Sliding Friction Disc
3085 42036 Plastic Boot-Replaces Front andRear Plastic Spindle Boots for Model 3000,4000, 4100 & 7700
3077 42081 Clutch, Drum Feed
3042 42700 Clutch Handle & Shaft AssemblyDrum Feed
3069 42080 Miter Gear, Drum Feed
3058 42702 Clutch Shifter Assembly
3060 42079 Clutch Spring, Drum feed
3040 42078 Shut-off Rod, Drum Feed
3043 42701 Drum Feed Dial Assembly
Page 3
3081 42703 Friction Disc Assembly, Drum Feed
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Replacement PartsAmmco Type
Brake Lathe
3088 40061 Handle, Belt Release
3090 40014D Handwheel - Drum Gear Box
3101 42021 1” arbor for 2002,3000,4000,4100, 7000, 7500, and 7700 lathes
3089 40033 Oil Seal Adapter Ring
3102 40081 Arbor Nutfor use with 3101 Arbor
3120 43120 1” Spacer for 11/16” Arbor(25.4mm) Long
3121 43109 1/2” Spacer for 11/16” Arbor(12.7mm) Long
3092 42083 Pin , Drum Feed
3122 40093 11/16” Arbor (Arbor Only)
3141 42096 3/16” Brass plug3141-30 42096-30 30 Pack
3142 40012 5/16” Brass Plug314250 40012-50 Brass Plug (50 Pack)
3153 40026 Spindle
3159 40041 Snap Ring, Spindle
Page 4
3110 44500 Spring for 1” Adapters3154 42097 Spindle Extension, Drum Feed
Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
3164 42057 Standard Oil Seal for 4000
3166 40042 Plug (Freeze Type)
3161 42031 V-Belt
3163 40039 Bearing Seal
Page 5
3165 42008 Self Aligning Washer (Old Style)
3170 40037A Shim, Bearing Seal
3171 40037B Shim, Bearing Seal
3169 40037 Shim, Bearing Seal
3172 40045 Retaining Ring
3180 40060 Set Screw, Belt Release
3176 40020 Woodruff Key, Handwheel ShifterHandle, Rotor Feed
3183 42044 Screw, Electrical Panel
3184 40134 Hex Nut, Drum Feed Lead Screw
3188 40102 Bronze Bushing, Front
3189 40101 Bronze Bushing, Back
3211-1 40003 Lead Screw Assembly, Cross Feed
3214 42058 Washer, Handwheel
3215 42055 Oil Filter Sleeve
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Replacement PartsAmmco Type
Brake Lathe
3224 40029 Set Screw, Spindle
3319 40070 Socket Head Cap Screw-Front Clamp
3338 42018 Set Screw, Twin Cutter
3372 40046 Pipe Plug, Oil Drain
3377 40051 Hex Nut, Motor Mount
3394 40035A Race, Drive Shaft
3393 40035 Bearing, Drive Shaft
3391 42084 Bearing, Drum Feed
3218 40145 Wrench, Small
3595 42033 Small Spring for Rubber Boot
4435 42006 Wire Boot Ring Use with3085 Spindle Boot
4670 42016 Lead Screw Nut, Drum Feed
4641 42086 Lead Screw Bone Washer, Drumfeed
3528 40129 Hex Jam Nut, Twin Cutter
4671 42087 Nut, Lead Screw Bushing
Page 6
3223 40049 Motor Shaft Bushing
3324 40140 Oval Washer, Drum FeedLead Screw
3392 42085 Race, Drum Feed
Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
6109 40125 Set Screw, Twin Cutter
6766 40048 O Ring, Motor Mount
6839 40018 Thumbscrew, Handwheel
5646 40152 Cap Screw, Rotor Feed
5689 40185 Set Screw, Sq.Head for Drum Bar5689-30 40185-30 Package of 30
6853 42028 Grease Fitting (Old Style)
6854 40013 Red Knob
6864 40057 Set Screw, Motor Mount
6871 42088 Thrust Bearing,Rotor Feed
6893 40076 Main Switch
Page 7
6058 40078 Cord Grip
5843 40106 Drum Boring Bar
6486 40028 Socket Head Cap Screw,Spindle
6825 42056 Socket Head Cap Screw,Spindle Lock
6841 40126 Groove Pin, Twin Cutter
6872 42089 Thrust Bearing, Rotor Feed
6873 42023 Thrust Bearing, Cross Feed
6874 40110 Thrust Washer, Cross Feed
6889 40090 Insulated Bushing, Electrical Panel
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Replacement PartsAmmco Type
Brake Lathe
6901 40103 Dial Assembly, Twin Cutter
6907 40113 Dial, Twin Cutter
6929 40112 Spring Washer, Twin Cutter6929-10 Package of 10
6934 40054 Square Head Screw, Twin Cutter
6950 40095N Twin Cutter
6977 40127 Plug, Twin Cutter
7209 40077 Electrical Cord
7005 40091 Draw bar & Nut Assembly
7344R 42053 Rear Flange
7075 11497 Silencer
Page 8
6905 40142 Spring, Twin Cutter
6906 40104 Threaded Plug, Twin Cutter
6908 40105 Dial Rod, Twin Cutter
6923 40115 Dial Knob, Twin Cutter 7338 42704 Pinion Bushing Assembly, Drum Feed
7343 42705 Control Lever & shift Assembly,Drum Feed
Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
7788 40065 Belt Guard
7963 40079 Worklight for 4000
7980 42013 Paint, Blue - One 12 OZ.Can
7996 42038 Shear Gear & C-Clip
7751 40074 Gear BoxReplaces 7751
7784 42029 Large Pulley
7782 42025 Guide Bar
7774 42005 Drive Rod
7764A 42091 Clutch Shaft, Rotor Feed
7748 42090 Shift Shaft, Rotor Feed
Page 9
7747 42012 Index Plate, Rotor Feed7747-10 42012-10 Package of 10
7750 42152 Facing Set
7755 42706 Gear Shift Assembly,Rotor Feed
7757 42707 Coupling Assembly, Rotor Assembly
7784-1 42029 Large Pulley with Pin
7744 42011 Shift Handle, Rotor Feed 7775 42092 Trap for Rotor Feed
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Replacement PartsAmmco Type
Brake Lathe
9611 40017 Dial Spring
9633 40014 Handwheel, Crossfeed
9634 40016 Dial, Crossfeed Handwheel
9645 40071 Lock Rod
9830 42060 Quill Gear
9249 40185 Set Screw, Tool Holder
9481 42001 Plastic ShieldPlastic Only is #11154
9444 42094 Washer used with 9443
9443 42093 Lock Nut , Drum Feed
Page 10
9626 40014A Handwheel, Crossfeed
9590 42051 Spindle Lock Set
9592 40067 Front Lock
9831 40027 Spindle Key
9708 40094 11/16” Arbor Assembly
9822 42095 Coupling & Pinion Assembly
Replacement Parts
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
9998 42019 Clamp, Rear Lower
9999 42020 Clamp, Rear Upper
10346 40063 Guide Bar
10868 42003 Rotor Feed Lead Screw Nut
11150 40154 Machine Screw, Plastic Shield
9836 40011 1/4”Brass Plug9836-30 40011-30 30 Pack
9837 42040 Guide Bar
9847 40040 Driveshaft / Worm Gear
9879 40128 Locating Screw, Twin Cutter
11152 42001G Thumb Screw
NA 40194 Safety Shield (New Style)
Page 11
1154 42001A Safety Shield
9918 42708 Short lead Screw & Miter Gear Assembly , 4000 Drum Feed
9919 42709 Long Led Screw & Miter Gear Assembly , 4100 Drum Feed
10868X 40068 Rotor FeedExtended Lead Screw Nut
9835 42074 Crossfeed
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Replacement PartsAmmco Type
Brake Lathe
29254 42001B Bracket to Chip Shield
24446 40069 Woodruff key for Large Pulley
23682 42032 Adapter Ring For Plastic Boot
22764 42015 Lampswitch Rubber Boot
22763 42014 Lampswitch
28584 40141 Tool Holder Gib, Twin Cutter
40141 40073 Serpintine Belt
40146 40022 Serpintine Pulley, Small
40142 40021 Serpintine Pulley, Large
11166 42001E Flange Hex Nut
11221 40099 Locking Nut for Long StudPart Of 11227
11224 40007 Washer for Nut Assembly 11227
11225 40008 Rubber Retainer for 11227
11227 40143 Locking Nut Assembly
11273 40066 Hex Nut, Belt Guard
20666 40005 Clamp, Boring Bar Lower
22006 40043 Grease Fitting (New Style)
21972 42048 Screw, Tappet Ground Electrical Panel
Page 12
20463 40085 Caution Plate
Adapters
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
3123 44142 Bell Clamp 5.75” OD146.05mm
3125 40161 1/2” Spacer, 1” hole
3191 45100 1” Spacer, 1 7/8” hole
3178 44007 Centering Cone 2.650” x3.224”67.31 x 81.89mm
3192 47102 2” Spacer, 1 7/8” hole50.80mm
3106 44010 Centering Cone3.421” x 4.031”86.89 x 102.39mm
3107 44008 Centering Cone2.890” x 3.500”73.41 x 88.90mm
3108 44006 Centering Cone 2.328” x 2.968”59.13 x 75.39mm
3109 44142 Bell Clamp 5.65” OD 143.52mm
3110 44500 Spring
3118 43121 19.5 x 34.93mm
3120 43120 11/16” Spacer 1” long
3121 43109 11/16” Spacer 1/2” long
Page 13
3127 47130 Step Adapter 1” x 11/16”
3193 45104 3” Spacer, 1 7/8’ hole76.20mm
AdaptersAmmco Type
Brake Lathe
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
3578 45142 Bell Clamp 7.25” OD1 7/8” hole198.45mm
3194 45030 Centering Cone2” x 3.375”1 7/8” hole(50.80 x 85.73mm
3577 45140 Bell Clamp 6.25” 1 7/8’ center hole158.75mm
3903 44001 Centering Cone1.187” x 2.250”30.16 x 57 15mm
3902 44000 Centering Cone 1.25” x 1.75”31.75 x 44.45mm
3590 45500 Spring
3904 44004 Centering Cone 1.703” x 2.750”43.26 x 69.85
4347 47545 1” Adapter Set
4732 A4732 Centering Cone4.656” x 5.25” 1 7/8” hole118.26 x 133.35mm
4776 44018 Centering Cone 2.750 x 3.3334”1 7/8” hole69.85 x 84.93mm
4777 44019 Centering Cone 3.281” x 3.891”1 7/8” hole 83.34 x 98.82mm
4778 45000 Centering Cone3.828” x 4.421”1 7/8” center Hole97.20 x 112.30mm
4779 45002 Centering Cone4.359” x 4.968”1 7/8” center Hole 110.70 x 126.20mm
Page 14
3581 45144 Bell Clamp 9.25”1 7/8” hole244.48mm
Adapters
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
8889 10433 Composite Rotor Plates for trucks10434 For GMC 4x4 & Chevy 1500
9192 44044 Double Tapered Collet1.711” x 2.073”43.46 x 52.65mm
9193 44046 Double Tapered Collet 2.074” x 2.440”52.68 x 61.98mm
4790 47120 Step Adapter 1 7/8” x 1”Set of three
Page 15
4781 45004 Centering Cone,4.891” x 5.500”1 7/8” center Hole 123.46 x 139.70mm
4782 45006 Centering Cone,5.438” x6.031”1 7/8” center Hole138.11 x 153.19mm
4783 45008 Centering Cone,5.969” x6.563”1 7/8” center Hole151.61 x 188.69mm
4784 45010 Centering Cone6.500” x 7.438”1 7/8” center Hole165.10 x 188.91mm
4785 45012 Centering Cone7.031” x 7.641”1 7/8” center Hole178.59 x 194.07mm
4786 45014 Centering Cone,7.578” x8.172”1 7/8” center Hole192.48 x202.57mm
8800 47300 RELS Hubless Adapte
8888 10430 Composite Rotor Adapter Plates/ cars10431 tauras/GM “W” Body Plates10432
AdaptersAdaptersAmmco Type
Brake Lathe
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
9198 45052 Collet, Double tapered 3.203” x 3.560”1 7/8” center Hole81.36 x 90.42mm
9232 44780 1” double Tapered Cone Set95.25 x 104.20mmPart of Adaptek System
9194 44048 Collet, Double tapered 2.441” x 2.897”62.00 x 73.58mm
9195 44054 Collet, Double tapered2.828” x 3.185”71.83 x 80.90mm
9196 44056 Collet, Double tapered 3.203” x 3.560”1 ” center Hole81.36 x 90.42mm
9197 45050 Collet, Double tapered2.828” x 3.185”1 7/8” center Hole71.83 x 80.90mm
Page 16
9310 49310 1” Adapter Setfor cars & Lt. Trk. to 1/2 TonPart of Adaptek System
9312 49312 1” Adapter Setfor Trucks up to 1/2 TonPart of Adaptek System
9311 49311 1” Adapter Setfor passenger carsPart of Adaptek System
9313 49313 1” Adapter Set for 3/4 & 1 ton Lt. Trk.Part of Adaptek System
9314 49314 1” Adapter setfor odd center holesPart of Adaptek System
Adapters
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
29576 40606 Light Truck Flange Plate7.25” 184.15mm
22138 43118 Spherical Washer Set
25882 43117 11/16’ Arbor Nut-Left Thread
25939 42098 11/16’ Arbor Nut-Right Thread
29572 40601 1” Adapter Base 4.80”121.92mm
29573 40602 Reversible Centering Cone2.05”-3.99”52.07 x 101.34mm
29574 40603 Spacer 2.00” Long50.08mm
29575 40605 Flange Plate for Autos 5.03”127.76mm
9489 44138 Bell Clamp 3.625”(92.08mm)OD
9490 44140 Bell Clamp 4.5” (114.30mm)OD
9492 40096 Self Aligning Spacer
9921 44040 Collet, Double Tapered1.322” x1.670”33.58 x42.42mm
9922 44042 Collet, Double Tapered1.362” x 1.710””
34.59 x 43.43mm
Page 17
9399 49399 1 7/8” Adapter Set4.656” x5.250”
118.26 x133.35mm
9499 47550 1 7/8” Adapter Set3.828” x 4.958”97.20 x 126.20mm
9708 40094 11/16” Arbor Set
Replacement PartsAmmco Type
Brake Lathe
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Adapters
29585 40616 Centering Cone 3.48” x 3.85”88.39 x 97.79mmPart of Adaptek System
29586 40621 Centering Cone3.75” x 4.13”95.25 x 104.20mmPart of Adaptek System
29587 40617 Centering Cone4.03” x 4.40”102.36 x 111.76 mmPart of Adaptek System
29591 40630 SpringPart Of Adaptek System
29578 40607 Lt. Truck Flange Plate6.625” (168.27mm)
29579 40610 Centering Cone1.84” x 2.20”(46.74 x 55.88mm)
29580 40611 Centering Cone2.12” x 2.48”(53.85 x 62.99mm)
29581 40612 Centering cone 2.38” x 2.75”(60.45 x 69.85mm)
29582 40013 Centering Cone 2.65” x 3.03”(67.31 x 76.96mm)
29583 40614 Centering Cone2.93” x 3.30”(74.42 x 83.82mm)
29584 40615 Centering Cone3.20” x 3.58”(81.28 x 90.93mm)
Page 18
29577 40608 Lg. Lt. truck flange Plate7.25” (184.15mm)
29590 40620 Centering Cone 4.85” x 5.23”123.19 x 132.84mmPart of Adaptek System
29589 40619 Centering Cone4.58” x 4.95”116.33 x 125.73mmPart of Adaptek System
29588 40618 Centering Cone 4.30” x 4.68”109.22 x 118.72 mmPart of Adaptek System
Carbide Bits
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
4724 45023 Left Hand Brazed Carbide Tool Bit 5/8” Square use on 6000,6002 lathe
40610 45010 Round Tool BitPackage of 10
NA 45020 Extra Thick Negative Rake Bitlasts longer-use in place of 6914Package of 10
45022 Titanium Coated Negative Rake Tool Bituse in place of 6914package of 10
NA 45016 New RELS bit for 4000, 7000 &7500 - works like the round bitbut gets in the cornersStandard bit on the RELS 2000Package of 10
NA 45021 Same as 45016but coated for longer lifePackage of 10
5677 45018 Heavy duty Positive Rake Bitfor 6000Use with 9695 Tool Bit
6914 45001 Negative Rake Bit for 1000, 2002,3000, 4000, 4100, 7000, 7500
6914-2 Two pack6914-6 Six Pack6914-10 Ten Pack6914-24 Package of 246914-48 Package of 48
6499 45019 Screw for 6914,6918,7681package of 10
6918 45017 Coated Positive Rake Bit for 3850,4000,7000,7500
6918-2 Package of 26918-6 Package of 6
7681 45002 Positive Rake Carbide Bit for 4000,7000 and 7500
7681-2 Package of 27681-6 Package of 67681-10 Package of 10
Page 19
4725 45024 Right hand Brazed Carbide Tool Bit 5/8” squareuse on 3000, 4000, 4100,5000,6000,6002 7700 lathe
4726 45025 Left Hand BrazedCarbide Tool Bit
1/2” square use on5000, 6000,6002
5720 45026 Right hand brazed carbide Tool bit5/8” square use on5000, 6000,6002
5725 45027 R/L Brazed Carbide Tool Bit5/8” square.
Use on 6000,6002 lathe
Replacement PartsAmmco Type
Brake Lathe
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Tool Holders
9695 45029 Heavy Duty Tool HolderUse with 5677 bitin Model 6000 Lathe
40609 45008 Positive Rake RoundLH Tool HolderUse with 40610 on 3850, 4000, 4100 and 7500 lathe.
5390 45028 use on 3850 lathe with 6918 bit
10702 45006 Negative Rake Left Handtool holder For Use with 3850
,4000,4100,and 7500 latheUse with 6914 bit
10651 45003 Right handed tool holderHolds 10701 tool HolderUse in 6900 and 6950 Twin Cutter
10701 45005 Negative Rake Right Hand Tool HolderUse in 3850,4000,4100,and 7500 lathe Use with 6914 bit
Page 20
40608 45009 Positive Rake RoundRH Tool HolderUse 40610 bit on 3850, 4000, 4100 and 7500 lathe.
5392 45029 Positive Rake for small drumsUse with 7681 bit in 3000,4000,& 7700 lathes
6999 45701 Set of two tools Bit Holders 0ne 10701-RH andone 10702 -LH Tool Bit HolderUse with 6914 negative rake bits
7999 45702 Set of two positive raketool bit holders
One 25968-RH andone 25969-LH Tool Bit Holder
Use with 7681 or 6918 Bit
9872 45007 Standard Negative Rakedrum toll holder
Use with 2002,30004000, 4100 and 7500 lathe
10650 45004 Left Handed Tool HolderHolds 10702 tool HolderUse in 6900 and6950 Twin Cutter
25968 45012 Positive Rake right hand tool holderUse with 7681 or 6418 bit on 3850, 4000, 4100 and 7500 lathe.
25969 45013 Positive rake left hand tool holderUse with 7681 or 6418 bit on 3850, 4000, 4100 and 7500 lathe.
90489R 45030 Curved Positive rake right hand tool holder. Use with 7681 or 6418 bit on 3850, 4000, 4100 and 7500 lathe.
90489L 45031 Curved positive rake left hand toolholder. Use with 7681 or 6418 bit on 3850, 4000, 4100 and 7500 lathe.
Vibration Dampeners
OEM Part # RELS Part # Description OEM Part # RELS Part # Description
Brake Lathe
1175 11491V Clip On Silencer
5280 11486V 1 3/4 Drum Silencer Band
6920 11488 Weighted Silencer Band
6921 24349 6.5” Rubber Silencer BandPackage of 2
6922 41003 9.25” Passenger Car DrumSilencer Band
Package of 2
9800 11494V Spring Silencer Band
Page 21
5290 11487V 2 3/4” Truck Drum Silencer Band
6930 11498 Heavy Duty Passenger CarDrum Silencer Band
7075 11497V Friction Rotor Silencer. Use on 3850,4000, 4100, and 7500 lathe
9183 42002 Replacement Pads for 7075
that will improve your
Ammco Brake Lathe
7000 Conversion & Upgrade KitGets rid of the old leaky feed mechanismWith our new gearbox and crossfeed you have an easy con-version of the 7000 brake lathe.This kit includes the gearbox and pulleys, the crossfeed, anda plate to cover up the hole.You get ride of the old leaky, high maintenance power take-off and end up with a great lathe that will amaze you withits speed and capability.
Part # 55700
3000 Conversion & Upgrade KitTurn that old style drum lathe into a ModernCombination Brake Lathe It will also eliminate chatter and vibration from your lathe which will
allow you to machine a rotor in less than three minutes and get a fantastic finish.
Part # 45152
4000 Conversion & Upgrade KitGives you variable speed capability for a fraction of thecost of a new LatheOur best selling Gearbox is now available for adramatically reduced price. This will allow an Ammcolathe to have a variable rotor speed function and gives aone cut pass capability to any Ammco 4000 lathe, no matter how oldthe lathe is!
Gearbox alone Part # 40074Gearbox, Pulleys & Belt Part# 50000
RELS Brake Lathe Products
Page 22