5/19/2018 ReM Product Accessory BOP
1/3
R&M Energy SystemsP.O. Box 2871
Borger, Texas, U.S.A. 79008-2871(800) 858-4158
(806) 274-5293 Fax: (806) 274-3418
R&M Energy Systems Canada9830 - 45th Avenue
Edmonton, Alberta, Canada T6E 5C5(800) 661-5659
(780) 437-6316 Fax: (780) 435-3074
* Corrosion resistant materials & coatings available,
contact customer service.** NACE stainless steel optional.*** Other
flange sizes available.
150H
Quick opening.
Acme cap thread eliminates cross-threading.
Cap with internal threads protected from the environment.
Blow-out proof ram screw.
Full opening.
Reinforced ram block reduces extrusion.
Cap o-ring provides reliable, pressure-tight seal.
200P
Taper threaded end caps.
Higher working pressure than 150H.
Full opening.
3 EUE thread connections.
Optional NACE trim.
Optional low temperature carbon steel.
Packing Gland
SPECIFICATIONS 150H 200P
Sizes Available 2 2-1/2 3 LP 2 2-1/2 3
Vertical Bore 1.975 2.560 2.970 2.120 2.440 3.000
Working Pressure 1500 PSI 2000 PSI
Body & Cap Material Ductile Iron* Ductile Iron*, Carbon
Steel
Ram Material See Page 17
Ram Screw & Packing Gland Carbon Steel** Alloy Steel
Ram Sizes Blind, 5/8-1, 1-1/8, 1-1/4, Blind, 5/8-1, 1-1/8,
1-1/4,1-1/2, 1-3/4 1-1/2, 1-3/4
NOTE: 150 H & 20 0P RAMS ARE NOT INTERCHANGEABLE
Ram Screw Packing Acrylic Braided PTFE NBR, HSN & FKM
Connection Male x Female Thread Male x Female Thread or
Flange
Optional Flange Connections N/A 2-1/16 2000, 2-9/16 2000,3-1/8
2000***
Height 9-1/2 10
Weight 43 lbs. 52 lbs.
Width (Rams Open) 20 26
Handles Optional Optional
Body
Ram Screw
O-Ring
Wing Cap
150 H Ram
Packing Ring
Packing Ring
Packing Glan
Tapered C
Ram Screw
200P Ram
Body
HERCULES Blow-Out Preventers 150H & 200P
5/19/2018 ReM Product Accessory BOP
2/3
HERCULES Blow-Out Preventers ITBOP, BOP Bonnet & Ram
R&M Energy SystemsP.O. Box 2871
Borger, Texas, U.S.A. 79008-2871(800) 858-4158
(806) 274-5293 Fax: (806) 274-3418
R&M Energy Systems Canada9830 - 45th Avenue
Edmonton, Alberta, Canada T6E 5C5(800) 661-5659
(780) 437-6316 Fax: (780) 435-3074
SPECIFICATIONS ITBOP
Sizes:
Top Flange 3-1/8 3000 PSI API
Bottom Flange 3-1/8 2000 & 3000 or 7-1/16 2000 &
3000
Side Outlets 2 LP x 2 LP or 2 LP x 3 LP
Vertical Bore 2.990
Body Ma terial Steel
Cap Material Ductile Iron, Carbon Steel
Ram Material See Chart BelowRam Screw Alloy Steel
Packing Gland Carbon Steel
Ram Sizes Blind, 5/8-1, 1-1/8, 1-1/4,1-1/2, 1-3/4
NOTE: 150H & 200P RAM S ARE NOT INTERCHANGEABLE
Packing Material NBR, HSN, FKM
Height 13-3/4
Weight 183 lbs.
Width (Rams Open) 26
Handles Optional
Note: Other sizes and options available, Contact Customer
Service.NACE stainless steel optional.
Integral Flow Tee BOP (ITBOP
) Integrates a flow tee with a BOP.
Uses 200P BOP rams.
Provides solid foundation for progressing cavity
pump drive.
Shorter overall height than separate components.
2000 PSI working pressure.
NACE available.
Low temperature carbon steel.
Nut
Patented
Illustration of M etal Reinforcement
Inside 150H & 200 P BOP Rams
Body
Packing Ring
Packing Gland
Ram Screw
200P RAM
Stud
Polished Rod
Top Connector
Top FollowerPacking
Body
Compression Nut
200P RAM
150H & 200P Ram Materials
NBR Compound C HSN FKM
Max. 250 F 300 F 325 F 400 FTemperature (121 C) (149 C) (163 C)
(204 C)
Max. H2S 2% 2% 10% 20%
Max. CO2 NR 10% 20% 5%
Tapered Cap
High Temperature BOP Bonnet Isolates stuffing box during
high
temperature steam injection. 1/4 NPT pressure tap. 1,000 F. (538
C) maximum service temperature. Allows pumping to resume after
steam injection. Steam goes down tubing instead of casing annulus.
Top Connection: 2-1/2 EUE, 3 LP, 3 EUE Bottom Connection: 2, 2-1/2,
or 3. Packing sizes available 1" through 1-3/4".
Contact Customer Service for avail ability of 300 0 PSIworkover
BOP with 4-1/16 vertical bore.
Bottom Follower
