TABLE OF CONTENTS PROVIDED IN THE INSTRUCTIONS Page # 1 Description & Features. Pages # 2 - 8 Wiring hints. IT IS MOST IMPORTANT THAT CORRECT POLARITY IS OBSERVED WHEN CONNECTING BATTERY PACKS. PLEASE READ INSTRUCTIONS BEFORE USE. DESCRIPTION. Thank you for choosing this Xenon made DSM2 Auto Bind Rx. The RCS # AB-TM receivers are compatible with all DSM2/DSMX transmitters. This Rx works best with 4 x rechargeable AA cells (4.8 volts) nominal supply. Up to 6 volts nominal. B . INDING N.B. The battery pack should be connected to the designated Batt - Bind terminal. 1) Tx must be OFF. Then provide power to the Rx unit. After 8 seconds Rx LED flashes quickly. 2) Ensure distance separation of 1 - 2 metres from receiver. Other Tx’s & Rx’s should be OFF. 3) Then press & hold Bind button & turn the Tx ON. Rx LED’s will go out. Tx will flash slowly. 4) After 10 seconds the Rx will come back on for two flashes & then after 5 seconds go solid on . 5) Solid Rx LED light ON means binding is completed. 6) Turn Rx OFF then Back ON again. FAILSAFE HAS BEEN DISABLED. RECEPTION. It is only the last 31 mm of the 20 cm antenna that actually receives the incoming signal. For maximum range in metal loco it may need to be placed outside the loco. OPERATION. Mount the Rx so that operation of the bright LED can be observed when binding etc. Unless Auto Binding, always switch Tx on first, then the Rx. When operation has finished switch the Loco OFF first, then the Rx. Ch # 1 SERVO REVERSED. Ch # 1 servos will rotate CW. That is backwards to most steam valves which rotate CCW to open & control Steam admission to the cylinders. If you must have it CW on the TX, use a servo reverser. ; OR You could operate prototypically and rotate the Tx handpiece knob CCW. SERVO REVERSERS. If a servo reverser is required for any Channel be certain you match the Servo Reverser max voltage to the battery pack you are using. See page # 6 P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: E mail: http://rcs-rc.com [email protected]# AB-TM Automatic Bind 2.4 Ghz DSM2 Rx Single 20 cm Diversity antenna. Thank you for purchasing this Xenon made DSM2 Rx. They can be used with any DSM2 Tx handpiece. Keep the Tx and Rx at least 1 x metre apart when binding. R C S 2.4 Ghz RADIO CONTROL Remote Control Systems
IT IS MOST IMPORTANT THAT CORRECT POLARITY IS OBSERVED WHEN CONNECTING BATTERY PACKS.
PLEASE READ INSTRUCTIONS BEFORE USE.
DESCRIPTION. Thank you for choosing this Xenon made DSM2 Auto Bind Rx.The RCS # AB-TM receivers are compatible with all DSM2/DSMX transmitters.
This Rx works best with 4 x rechargeable AA cells (4.8 volts) nominal supply. Up to 6 volts nominal. B .INDING N.B. The battery pack should be connected to the designated Batt - Bind terminal.1) Tx must be OFF. Then provide power to the Rx unit. After 8 seconds Rx LED flashes quickly.2) Ensure distance separation of 1 - 2 metres from receiver. Other Tx’s & Rx’s should be OFF. 3) Then press & hold Bind button & turn the Tx ON. Rx LED’s will go out. Tx will flash slowly.4) After 10 seconds the Rx will come back on for two flashes & then after 5 seconds go solid on .5) Solid Rx LED light ON means binding is completed. 6) Turn Rx OFF then Back ON again.FAILSAFE HAS BEEN DISABLED. RECEPTION. It is only the last 31 mm of the 20 cm antenna that actually receives the incoming signal. For maximum range in metal loco it may need to be placed outside the loco. OPERATION. Mount the Rx so that operation of the bright LED can be observed when binding etc.Unless Auto Binding, always switch Tx on first, then the Rx.When operation has finished switch the Loco OFF first, then the Rx.Ch # 1 SERVO REVERSED. Ch # 1 servos will rotate CW. That is backwards to most steam valves which rotate CCW to open & control Steam admission to the cylinders. If you must have it CW on the TX, use a servo reverser. ; ORYou could operate prototypically and rotate the Tx handpiece knob CCW.SERVO REVERSERS. If a servo reverser is required for any Channel be certain you match the Servo Reverser max voltage to the battery pack you are using. See page # 6
N.B. The battery feed plug can go into any RX terminal when “binding”.Observe correct polarity.
SIDE VIEW OF # AB-EM RX.
SERVO PLUGYELLOW/WHITE SIGNAL
BLACK (NEGATIVE)
RED (POSITIVE)
SERVO PLUG
SIDE VIEW OF # AB-TM RX
YELLOW/WHITE/ORANGE (SIGNAL)BLACK (NEGATIVE)
RED (POSITIVE)Dual 20cm
Diversity Antennas
AB-TM
6ch RX v2.TOP
CONNECTING SERVOS FOR# AB-EM & Rx’s# AB-TM
Three wire cable. Ensure plugs are correctly located. wire towards top - inwards of RX.Orange/White
To BatteryCharger
RX BATTERY PACK
Min = 4.4 voltsMax = 4.8 volts.
NOMINAL.Use rechargeable cells
instead of dry cells
To help prevent any accidental shorting of bare servo pins,use the supplied blanking plugs to cover unused servo pins.
AB-TM6ch RX.
TOP
Y R
B
BA
TT
- BIN
D (1)
(2)
(3)
(4)
(5)
(5) # SSLS
5v
FL
RL
WIRING THE RCS #MRW-SSLS w/LED’s or BULBSfor automatic directional lights using a
or Rx# AB-EM # AB-TM
GROUND (-) IS VIA THE SERVO CABLE.
POWER FOR BULBS CAN COMEFROM TRACTION BATTERIES.
FIT 5 VOLT BULBS IF R/C BATTS USED FOR POWER
YELLOW & WHITE WIRESGO TO FL & RL ON THE # SSLS
PLUG REVERSER SERVOINTO THE THREE PINS ON # MRW-SSLS.
MATCH WIRE POLARITY.
White
Front LEDLED’s must have a suitable droppingresistor fitted in either the
+ (positive) or - (negative) circuit.
Rear LED
BLUE 5 volt wire goes to long legs of LED’s
Yellow470R
470R
Match light bulbs withthe traction battery voltage.
Rear Bulb
Yellow
White
Red +
Front Bulb
Ch # 3 Reverser servo.
GROUND (-) IS VIA THE SERVO CABLE.
SIDE VIEW OF # AB-EM RX.
SERVO PLUGYELLOW/WHITE SIGNAL
BLACK (NEGATIVE)
RED (POSITIVE)
SERVO PLUG
SIDE VIEW OF # AB-TM RX
YELLOW/WHITE/ORANGE (SIGNAL)BLACK (NEGATIVE)
RED (POSITIVE)Dual 20cm Diversity Antennas.
Y R
B
(1)
(2)
(3)
(4)
(5)
(5)
# LYN SOUND
Speaker Terminals
Auxiliary audio out
Common ground for audio
AB-TM
6ch RX v2.TOP
Y R
B
BA
TT
- BIN
D
BIN
D B
UT
TO
N
(1)
(2)
(3)
(4)
(5)
(6)
WIRING THE RCS #MRW LYN-SOUNDusing a Rx# AB-TM
For use up to 6.0 volt nominal.
Dual 20cm Diversity Antennas
SET
MRW-SSSS
The # MRW-SSSS has been designed specifically to work with the Ch # 5 Bind button found on all RCS Tx handpieces. Simply plug the servo cable lead into Ch # 5 or any spare Ch.The OFF position is above 1.5 ms. The switch triggers below 1.45 ms
No common ground connection is neededas long as sound is powered by the
traction batteries.
MyLOCOSOUND
Whistle/Horn
Bell/Horn
Guards Whistle
Blowdown/Brake
Air Pump/Turbo
COM
1
CHUFF TIMER
ACTUAL SIZE OF # MRW-SSSSIS 22 mm X 11 mm X 10 mm.
SET
N OPEN
N OPEN
N CLOSE
N CLOSE
COMMON
COMMON
MR
W-R
DS
Plug # MRW-RDS into any centre idle channel.
Max 1 amp loadon each relay.
MyLOCOSOUND
Whistle/Horn
Bell/Horn
Guards Whistle
Blowdown/Brake
Air Pump/Turbo
CHUFF TIMER
SET COM
2
1
MRW-SSDS
Plug # MRW-SSDS into any sparechannel with a centre idle.
No common ground connection is neededas long as sound is powered by the
traction batteries.
Max 2 amp load on each trigger.
MyLOCOSOUND
Whistle/Horn
Bell/Horn
Guards Whistle
Blowdown/Brake
Air Pump/Turbo
CHUFF TIMER
COM
COM
2
2
1
1
SET
SET
MRW-SSQS
Plug # MRW-SSQS into any sparetwo channels with a centre idle. No common ground connection is needed
as long as sound is powered by the traction batteries.
Max 2 amp load on each trigger.
MyLOCOSOUND
Whistle/Horn
Bell/Horn
Guards Whistle
Blowdown/Brake
Air Pump/Turbo
CHUFF TIMER
TWO TRIGGERS PER CHANNEL.
# M
RW
-SS
TS
The # MRW-SSTS has been designed specifically to work with the RCS # EVO TX-20handpieces. They have three separate trigger functions:Plug into any spare three channels.Usually Ch # 2 (F2) & Ch # 4 (F4) OR: the third servo lead into channel # 5.
No common ground connection is neededas long as sound is powered by the
traction batteries.Max 2 amp load on each trigger.
Use the simple # PnP-BATT kit for Aristo Craft and Bachmann locos fitted wth PnP sockets.A suitable fuse must be used for system protection. A 5 amp fast blow fuse should be used for most locos.
