Research ArticleMIMO-Based Forward-Looking SARImaging Algorithm and Simulation
Ziqiang Meng, Yachao Li, Shengqi Zhu, Yinghui Quan, Mengdao Xing, and Zheng Bao
National Laboratory of Radar Signal Processing, Xidian University, Xi’an 710071, China
Correspondence should be addressed to Yachao Li; [email protected]
Received 25 March 2014; Revised 17 June 2014; Accepted 29 June 2014; Published 15 July 2014
Academic Editor: Wei Xu
Copyright © 2014 Ziqiang Meng et al. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Multiple-inputmultiple-output (MIMO) radar imaging can provide higher resolution and better sensitivity and thus can be appliedto targets detection, recognition, and tracking. Missile-borne forward-looking SAR (MFL-SAR) is a new and special MIMO radarmode. It has advantage of two-dimensional (2D) imaging capability in forward direction over monostatic missile-borne SAR andairborne SAR. However, it is difficult to obtain accurate 2D frequency spectrum of the target echo signal due to the high velocityand descending height of this platform, which brings a lot of obstacles to imaging algorithm design. Therefore, a new imagingalgorithm for MFL-SAR configuration based on the method of series reversion is proposed in this paper. This imaging methodcan implement range compression, secondary range compression (SRC), and range cell migration correction (RCMC) effectively.Finally, some simulations of point targets and comparison results confirm the efficiency of our proposed algorithm.
1. Introduction
Radar imaging is an emerging technology which can providea high resolution radar image of targets in long distance inde-pendent of weather conditions and sunlight illumination,and it is being more and more widely used in military andcivil fields [1–5]. Multiple-input multiple-output (MIMO)radar is an antenna system which transmits multiple probingsignals via its antennas and scattering signals are received bydistributed receiving antennas [6–9]. Application of MIMOradar to radar imaging could provide higher resolutionand better sensitivity and thus can be applied to detection,recognition, and tracking of targets [10–12].
We consider a new MIMO radar system, that is, missile-borne multistatic synthetic aperture radar (MFL-SAR) asshown in Figure 1, in which transmitting signals are transmit-ted simultaneously and the reflected signals at receivers canbe processed independently. This configuration can beapplied to missile precision terminal guidance because of itsadvantages of 2D imaging ability in forward direction overmonostatic SAR [13, 14]. Missile precision terminal guidancecould conduct good performance in targets detection, recog-nition, orientation tracking, and attacking [15, 16]. During themoving period, transmitter and receiver cooperate with each
other, and transmitter irradiates the imaging area with somesquint angle, while receiver receives the target echo signals inforward-lookingmode.Without loss of generality and for theconvenience of description, missile-borne bistatic forward-looking SAR (MBFL-SAR) configuration is considered in thispaper.
Effective and efficient imaging in this configuration is animportant technology for missile precision terminal guid-ance; therefore, imaging algorithm for MBFL-SAR is neces-sary and essential. Many investigations on SAR imaging havebeen published and some appealing approaches have beensuggested. Range-Doppler algorithm (RDA) [17–19] andchirp scaling algorithm (CSA) [20] are conventional mono-static algorithms which are applied to those configurationsthat have azimuth-invariant property. For bistatic SAR imag-ing, some other methods have been proposed. Soumekhderived the 2D spectrum expression of bistatic SAR andproposed a new RMA for bistatic configuration through twoapproximations in the derivation [21–23]. But this algorithmis limited to the bistatic parallel configuration because ofidentical velocity vectors of transmitter and receiver. Neoet al. and Davidson et al. proposed a nonlinear CS algorithmin [24, 25], but it neglected space-variance of Doppler fre-quency in range direction and influence of secondary range
Hindawi Publishing CorporationInternational Journal of Antennas and PropagationVolume 2014, Article ID 783949, 9 pageshttp://dx.doi.org/10.1155/2014/783949
2 International Journal of Antennas and Propagation
Target area
Transmitters
Receivers
Figure 1: An illustration of MFL-SAR configuration.
compression (SRC) on imaging. A simple operator named“dip move out” (DMO) is used to transform a bistatic surveyinto a monostatic one in [26, 27]. The initial dataset is usedto convolve with the so-called smile, a short operator, and theoutput is the equivalent monostatic data. Unfortunately, theso-called smile is space-variant both in range direction and inazimuth direction, and the changes of wave number in rangedirection are also neglected.
An imaging algorithm based on the method of seriesreversion [28, 29] for MBFL-SAR is suggested in this paper.By unfolding the Doppler frequency, the stationary phasepoint expansion coefficients are obtained,whichmakes it easyto get the 2D frequency spectrum of the target echo signal.Then imaging method can be obtained based on the 2D fre-quency spectrum. Range compression is implemented in therange frequency domain, and SRC can be finished in the 2Dfrequency domain. The RCM can be corrected in the range-Doppler domain and finally the imaging result can be gotthrough azimuth compression.
The rest of this paper is organized as follows. Geometricconfiguration and signalmodel ofMBFL-SAR are introducedin Section 2. Also, the difficulty in direct-using the principleof stationary phase (POSP) is discussed. In Section 3, thederivation of 2D frequency spectrum of the target echosignal is given based on the accurate approximation of theslant range history, in which the high-order terms cannot beignored owing to the presence of high velocities and accel-erations. The proposed imaging algorithm is described inSection 4 and numerical simulations are achieved to show theeffectiveness of our proposed method, and the resultsare given in Section 5. Finally, conclusions are drawn inSection 6.
2. Geometric Configuration and Signal Model
Figure 2 depicts geometric configuration of MBFL-SAR, inwhich both transmitter and receiver travel curvilinear
Point target
Z
R
HR
O
d
O
x
xpHT
→
�t
→
�r
yp
P(xp, yp, 0)
T
y
𝜓
Figure 2: Geometric configuration of MBFL-SAR.
descending motion. 𝑂 is the origin of coordinates, 𝑂 is theprojection of transmitter when the slow time 𝑡
𝑚= 0, and
|𝑂𝑂| = 𝑑. Transmitter is moving with the original velocity
vectors V⃗𝑡0= (V𝑡𝑥0, V𝑡𝑦0, V𝑡𝑧0) and acceleration vectors ⃗𝑎
𝑡=
(𝑎𝑡𝑥, 𝑎𝑡𝑦, 𝑎𝑡𝑧). And the ones of receiver are V⃗
𝑟0= (0, V
𝑟𝑦0, V𝑟𝑧0)
and ⃗𝑎𝑟= (0, 𝑎
𝑟𝑦, 𝑎𝑟𝑧), respectively. There exists an included
angle 𝜓 between the two planes in which the two platformstravel.The transmitter keeps illuminating the imaging area inside-looking mode, and the receiver looks in forward direc-tion. The receiver antenna gets the echo signal reflectedfrom the imaging area which the receiver moves towards.Assume that transmitter and receiver are at 𝑇
0(𝑑, 0,𝐻
𝑇) and
𝑅0(0, 0,𝐻
𝑅) when 𝑡
𝑚= 0, and velocity vectors of them at
the moment 𝑡𝑚(𝑡𝑚̸= 0) are V⃗
𝑡= (V𝑡𝑥, V𝑡𝑦, V𝑡𝑧) and V⃗
𝑟= (V𝑟𝑥,
V𝑟𝑦, V𝑟𝑧), respectively, where V
𝑡𝑥, V𝑡𝑦, and V
𝑡𝑧denote the veloc-
ity components of V⃗𝑡in the directions𝑥,𝑦, and 𝑧, respectively;
and V𝑟𝑥, V𝑟𝑦, and V
𝑟𝑧are the ones of V⃗
𝑟, respectively.
The bistatic slant range at time instant 𝑡𝑚can be obtained
as
𝑅𝑏𝑓(𝑡𝑚) = 𝑅𝑇(𝑡𝑚) + 𝑅𝑅(𝑡𝑚)
= √(𝑥𝑡− 𝑥𝑝)2
+ (𝑦𝑡− 𝑦𝑝)2
+ 𝑧2
𝑡
+ √(𝑥𝑟− 𝑥𝑝)2
+ (𝑦𝑟− 𝑦𝑝)2
+ 𝑧2𝑟,
(1)
with
𝑥𝑡= 𝑑 + V
𝑡𝑥0𝑡𝑚+ 0.5𝑎
𝑡𝑥𝑡2
𝑚, 𝑥
𝑟= 0,
𝑦𝑡= V𝑡𝑦0𝑡𝑚+ 0.5𝑎
𝑡𝑦𝑡2
𝑚,
𝑦𝑟= V𝑟𝑦0𝑡𝑚+ 0.5𝑎
𝑟𝑦𝑡2
𝑚,
𝑧𝑡= 𝐻𝑇+ V𝑡𝑧0𝑡𝑚+ 0.5𝑎
𝑡𝑧𝑡2
𝑚,
𝑧𝑟= 𝐻𝑅+ V𝑟𝑧0𝑡𝑚+ 0.5𝑎
𝑟𝑧𝑡2
𝑚,
(2)
where 𝑥𝑡, 𝑦𝑡, and 𝑧
𝑡represent the locations of transmitter in
directions 𝑥, 𝑦, and 𝑧, respectively; and 𝑥𝑟, 𝑦𝑟, and 𝑧
𝑟are the
ones of receiver, respectively.
International Journal of Antennas and Propagation 3
Suppose that the transmitted waveform is the linear fre-quency modulation (LFM), and scattering from 𝑃(𝑥
𝑝, 𝑦𝑝, 0)
to the receiver can be written as
𝑠 (�̂�, 𝑡𝑚) = 𝑤𝑟(�̂� −
𝑅𝑏𝑓(𝑡𝑚)
𝑐)𝑤𝑎(𝑡𝑚)
× exp[
[
𝑗𝜋𝛾(�̂� −𝑅𝑏𝑓(𝑡𝑚)
𝑐)
2
]
]
× exp[−𝑗2𝜋𝜆𝑅𝑏𝑓(𝑡𝑚)] ,
(3)
where �̂� is the range time, 𝜆 is the wavelength, 𝑐 is the speed oflight, and 𝛾 is the chirp rate.𝑤
𝑟(⋅) and𝑤
𝑎(⋅) are the range and
azimuth envelopes, respectively.By applying a range fast Fourier transform (FFT) to (3),
we can obtain
𝑠 (𝑓𝑟, 𝑡𝑚) = 𝑊
𝑟(𝑓𝑟) 𝑤𝑎(𝑡𝑚) ⋅ exp(−𝑗𝜋
𝑓2
𝑟
𝛾)
⋅ exp [−𝑗2𝜋𝑐(𝑓𝑟+ 𝑓𝑐) 𝑅𝑏𝑓(𝑡𝑚)] ,
(4)
where 𝑓𝑟represents the range frequency.
The 2D frequency spectrum of the echo signal can beobtained by an azimuth FFT, expressed as
𝑆 (𝑓𝑟, 𝑓𝑎) = ∫
+∞
−∞
𝑠 (𝑓𝑟, 𝑡𝑚) exp (−𝑗2𝜋𝑓
𝑎𝑡𝑚) 𝑑𝑡𝑚, (5)
where 𝑓𝑎represents the azimuth frequency, and the phase in
(5) can be written as
Θ(𝑡𝑚) = −𝜋
𝑓2
𝑟
𝛾−2𝜋
𝑐(𝑓𝑟+ 𝑓𝑐) 𝑅𝑏𝑓(𝑡𝑚) − 2𝜋𝑓
𝑎𝑡𝑚. (6)
By applying the POSP, we have
−2𝑐
𝑓𝑐+ 𝑓𝑟
𝑓𝑎=
𝛼𝑡1+ 2𝛼𝑡2𝑡𝑚+ 3𝛼𝑡3𝑡2
𝑚+ 4𝛼𝑡4𝑡3
𝑚
√𝑅2
𝑡0+ 𝛼𝑡1𝑡𝑚+ 𝛼𝑡2𝑡2𝑚+ 𝛼𝑡3𝑡3𝑚+ 𝛼𝑡4𝑡4𝑚
+𝛼𝑟1+ 2𝛼𝑟2𝑡𝑚+ 3𝛼𝑟3𝑡2
𝑚+ 4𝛼𝑟4𝑡3
𝑚
√𝑅2
𝑟0+ 𝛼𝑟1𝑡𝑚+ 𝛼𝑟2𝑡2𝑚+ 𝛼𝑟3𝑡3𝑚+ 𝛼𝑟4𝑡4𝑚
,
(7)
with
𝑅𝑡0= √(𝑑 − 𝑥
𝑝)2
+ 𝑦2𝑝+ 𝐻2
𝑇,
𝑅𝑟0= √𝑥2
𝑝+ 𝑦2𝑝+ 𝐻2
𝑅,
𝛼𝑡1= 2 [V
𝑡𝑥0(𝑑 − 𝑥
𝑝) − 𝑦𝑝V𝑡𝑦0+ V𝑡𝑧0𝐻𝑇] ,
𝛼𝑟1= 2 (−V
𝑟𝑦0𝑦𝑝+ V𝑟𝑧0𝐻𝑅) ,
𝛼𝑡2= V2𝑡𝑥0+ 𝑎𝑡𝑥(𝑑 − 𝑥
𝑝) + V2𝑡𝑦0− 𝑎𝑡𝑦𝑦𝑝+ V2𝑡𝑧0+ 𝑎𝑡𝑧𝐻𝑇,
𝛼𝑟2= V2𝑟𝑦0+ V2𝑟𝑧0− 𝑎𝑟𝑦𝑦𝑝+ 𝑎𝑟𝑧𝐻𝑅,
𝛼𝑡3= 𝑎𝑡𝑥V𝑡𝑥0+ 𝑎𝑡𝑦V𝑡𝑦0+ 𝑎𝑡𝑧V𝑡𝑧0,
𝛼𝑟3= 𝑎𝑟𝑦V𝑟𝑦0+ 𝑎𝑟𝑧V𝑟𝑧0,
𝛼𝑡4=1
4(𝑎2
𝑡𝑥+ 𝑎2
𝑡𝑦+ 𝑎2
𝑡𝑧) ,
𝛼𝑟4=1
4(𝑎2
𝑟𝑦+ 𝑎2
𝑟𝑧) .
(8)
If Θ(𝑡∗𝑚) = 0, we can get the stationary point 𝑡∗
𝑚, but we
can see that it is very difficult to determine the stationarypoint 𝑡∗
𝑚from (7), so 2D frequency spectrum of the echo
signal cannot be obtained through direct POSP. Some otherapproaches should be taken to get 2D frequency spectrum ofthe echo signal.
3. Derivation of 2D Frequency SpectrumBased on Series Reversion
According to [28], it needs to take efficient approximation ofthe slant range 𝑅
𝑏𝑓(𝑡𝑚) before using the method of series
reversion. Because of the high velocity and acceleration in themissile platform, it needs to keep the terms up to the third-order
𝑅𝑏𝑓(𝑡𝑚) = 𝑅𝑏𝑓0+ 𝑘1𝑡𝑚+ 𝑘2𝑡2
𝑚+ 𝑘3𝑡3
𝑚+ ⋅ ⋅ ⋅ , (9)
with
𝑅𝑏𝑓0
= 𝑅𝑡0+ 𝑅𝑟0,
𝑘1=𝛼𝑡1
2𝑅𝑡0
+𝛼𝑟1
2𝑅𝑟0
,
𝑘2=𝛼𝑡2
2𝑅𝑡0
−𝛼2
𝑡1
8𝑅3
𝑡0
+𝛼𝑟2
2𝑅𝑟0
−𝛼2
𝑟1
8𝑅3
𝑟0
,
𝑘3=𝛼𝑡3
2𝑅𝑡0
−𝛼𝑡1𝛼𝑡2
4𝑅3
𝑡0
+𝛼3
𝑡1
16𝑅5
𝑡0
+𝛼𝑟3
2𝑅𝑟0
−𝛼𝑟1𝛼𝑟2
4𝑅3
𝑟0
+𝛼3
𝑟1
16𝑅5
𝑟0
.
(10)
To apply the method of series reversion, the linear rangecell migration (LRCM) should be removed firstly. LetΘ(𝑡𝑚) = 0, we have
−𝑐
𝑓𝑐+ 𝑓𝑟
𝑓𝑎= 2𝑘2𝑡𝑚+ 3𝑘3𝑡2
𝑚. (11)
Then through the method of series reversion, the expres-sion of the stationary phase point can be expressed byunfolded Doppler frequency as
𝑡𝑚(𝑓𝑎) = 𝐴
1(−
𝑐
𝑓𝑐+ 𝑓𝑟
𝑓𝑎) + 𝐴
2(−
𝑐
𝑓𝑐+ 𝑓𝑟
𝑓𝑎)
2
+ ⋅ ⋅ ⋅ ,
(12)
where 𝐴1= 1/2𝑘
2, 𝐴2= −3𝑘
3/8𝑘3
2.
4 International Journal of Antennas and Propagation
Having obtained the stationary phase point, we shouldreintroduce the LRCM term to calculate 2D frequency spec-trum of the echo signal. By (5), (6), and (12), 2D frequencyspectrum of the echo signal is written as
𝑆MSR (𝑓𝑟, 𝑓𝑎)
= 𝑊𝑟(𝑓𝑟)𝑊𝑎(𝑓𝑎) exp[−𝑗𝜋
𝑓2
𝑟
𝛾] exp [𝑗Φ (𝑓
𝑟, 𝑓𝑎)] ,
(13)
where
Φ(𝑓𝑟, 𝑓𝑎) = −2𝜋
𝑓𝑐+ 𝑓𝑟
𝑐𝑅𝑏𝑓0− 𝜋
𝑓2
𝑟
𝛾
+ 2𝜋𝑐
4𝑘2(𝑓𝑐+ 𝑓𝑟)(𝑓𝑎+ (𝑓𝑐+ 𝑓𝑟)𝑘1
𝑐)
2
+ 2𝜋𝑘3𝑐2
8𝑘3
2(𝑓𝑐+ 𝑓𝑟)2(𝑓𝑎+ (𝑓𝑐+ 𝑓𝑟)𝑘1
𝑐)
3
.
(14)
It can be seen that the coefficient of the third-term inthe slant range is included in Φ(𝑓
𝑟, 𝑓𝑎), which indicates the
presence of the high-order terms introduced by high velocityand acceleration of this configuration into 2D frequency spec-trum. The imaging algorithm can be designed based on 2Dfrequency spectrum, which will be discussed in the nextsection.
4. Imaging Algorithm for MBFL-SAR
Todesign imaging algorithmefficiently, the phase term in (14)should be decomposed using Taylor series firstly because ofthe range/azimuth frequency coupling in 2D frequency spec-trum, and the series expansions are as follows:
Φ(𝑓𝑟, 𝑓𝑎) ≈ Φ
𝑟𝑔(𝑓𝑟) + Φ𝑎(𝑓𝑎) + Φrcm (𝑓𝑟, 𝑓𝑎)
+ Φsrc (𝑓𝑟, 𝑓𝑎) + Φres,(15)
with
Φ𝑟𝑔(𝑓𝑟) = −𝜋
𝑓2
𝑟
𝛾, (16)
Φ𝑎(𝑓𝑎)
= 2𝜋{1
4𝑘2
(𝑘2
1
𝑐+ 2𝑘1𝑓𝑎+𝑐
𝑓𝑐
𝑓2
𝑎)
+𝑘3
8𝑘3
2
[𝑘3
1
𝑐+ 3𝑘2
1𝑓𝑎+ 3𝑘1
𝑐
𝑓𝑐
𝑓2
𝑎+ (
𝑐
𝑓𝑐
)
2
𝑓3
𝑎]} ,
(17)
Φrcm (𝑓𝑟, 𝑓𝑎)
= 2𝜋𝑓𝑟{−𝑅𝑏𝑓0
𝑐+1
4𝑘2
[𝑘2
1
𝑐− 𝑐(
𝑓𝑎
𝑓𝑐
)
2
]
+𝑘3
8𝑘3
2
[𝑘3
1
𝑐− 3𝑘1𝑐(𝑓𝑎
𝑓𝑐
)
2
− 2𝑐2(𝑓𝑎
𝑓𝑐
)
3
]} ,
(18)
Table 1: Parameters used in the simulations.
Wavelength 0.02m
Bandwidth 50MHz
Sampling frequency 100MHz
Pulse duration 2 𝜇s
Scene center location (0, 4500, 0)
Fringe point location (300, 4800, 0)
𝜓 10∘
PRF 10KHz
𝐻𝑇
35 km
𝐻𝑅
30 km
V⃗𝑡0
(434.1, 2462.0, −2000) m/s
⃗𝑎𝑡
(−8.7, −49.2, 30) m/s2
V⃗𝑟0
(0, 2500, −2000) m/s
⃗𝑎𝑟
(0, −50, 30) m/s2
Φsrc (𝑓𝑟, 𝑓𝑎)
= 2𝜋{1
4𝑘2
𝑐
𝑓𝑐
((𝑓𝑟
𝑓𝑐
)
2
− (𝑓𝑟
𝑓𝑐
)
3
)𝑓2
𝑎
+𝑘3
8𝑘3
2
[3𝑘1
𝑐
𝑓𝑐
((𝑓𝑟
𝑓𝑐
)
2
− (𝑓𝑟
𝑓𝑐
)
3
)𝑓2
𝑎
+ (𝑐
𝑓𝑐
)
2
(3(𝑓𝑟
𝑓𝑐
)
2
− 4(𝑓𝑟
𝑓𝑐
)
3
)𝑓3
𝑎]} ,
(19)
Φres = −2𝜋𝑓𝑐𝑅𝑏𝑓0
𝑐. (20)
The term in (16) represents the range compression termwhich is independent of the azimuth frequency 𝑓
𝑎. Thus the
data can be range-compressed in the range frequency azim-uth time domain or in the 2D frequency domain alternatively.The term in (17) denotes the azimuth compression term,dependent only on 𝑓
𝑎and used in the azimuth compression.
It should be implemented after range compression andRCMC in the range time azimuth frequency domain as 𝑘-coe-fficients are range variant.The term in (18) indicates the RCMtermwhich is linearly dependent on the range frequency𝑓
𝑟. It
needs to be compensated because of the coupling betweenrange and azimuth. Similar to the azimuth compression term,this term should be implemented in the range time azimuthfrequency domain. Note that −2𝜋(𝑅
𝑏𝑓0/𝑐)𝑓𝑟is the linear
phase representing the location of target point; the energyof the target will be focused within the corresponding rangecell after RCMC. It should be paid attention to in the imagingprocess. The term in (19) is the SRC term which indicates the
International Journal of Antennas and Propagation 5
Table 2: Image quality parameters using the proposed method.
Parameter Theoretical one Center point Fringe point
Azimuth Range Azimuth Range Azimuth Range
PSLR (dB) −13.26 −13.26 −13.27 −13.15 −13.25
ISLR (dB) −9.8 −10.07 −9.97 −10.04 −9.97
1
0.8
0.6
0.4
0.2
0
600600
400400
200 2000 0
Nor
mal
ized
ampl
itude
Range (samples)Azimu
th (samples)
(a) 2D impulse response
200 300 400 500 600 700 800
0
Azimuth (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(b) Azimuth impulse response
200 300 400 500 600 700 800
0
Range (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(c) Range impulse response
Figure 3: Center point results using the proposed range model.
coupling between𝑓𝑟and𝑓𝑎. It may cause significant degrada-
tion in the imaging resolution if uncompensated and is com-pensated in the 2D frequency domain. The last residual termin (20) is independent of the range frequency or the azimuthfrequency. It has no effect on the imaging focus and thus canbe neglected in MBFL-SAR configuration.
Consequently, the main procedure of the proposed algo-rithm follows the following steps.
(1) Use 2D FFT to transform the echo signal to 2Dfrequency domain as shown in (13).
(2) Design the match filtering function in the 2D fre-quency domain to compensate the range compression
term, the SRC term, and the residual term. Thematch filtering function𝐻
1(𝑓𝑟, 𝑓𝑎) can be obtained as
follows:
𝐻1(𝑓𝑟, 𝑓𝑎) = exp [−𝑗 (Φ
𝑟𝑔(𝑓𝑟) + Φsrc (𝑓𝑟, 𝑓𝑎) + Φres)] .
(21)
(3) Apply range inverse fast Fourier transform (IFFT) toconvert the signal to the range time azimuth fre-quency domain and correct the RCM term.
(4) Finish azimuth compression bymultiplying the rangetime azimuth frequency domain signal with the
6 International Journal of Antennas and Propagation
1
0.8
0.6
0.4
0.2
0
600600400
400200
2000 0
Nor
mal
ized
ampl
itude
Range (samples)Azimu
th (samples)
(a) 2D impulse response
200 300 400 500 600 700 800
0
Azimuth (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(b) Azimuth impulse response
200 300 400 500 600 700 800
0
Range (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(c) Range impulse response
Figure 4: Fringe point results using the proposed range model.
Azimuth (samples)
Rang
e (sa
mpl
es)
200 400 600 800 1000
200
400
600
800
1000
(a) Quadratic range model
Azimuth (samples)
Rang
e (sa
mpl
es)
200 400 600 800 1000
200
400
600
800
1000
(b) Proposed range model
Figure 5: Contour plots comparison using different range models.
International Journal of Antennas and Propagation 7
200 300 400 500 600 700 800
0
Azimuth (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(a) Quadratic range model
200 300 400 500 600 700 800
0
Azimuth (samples)
Nor
mal
ized
ampl
itude
(dB)
−40
−35
−30
−25
−20
−15
−10
−5
(b) Proposed range model
Figure 6: Azimuth impulse responses comparison using different range models.
azimuth match filtering function, which can beobtained as follows:
𝐻2(𝑡𝑚, 𝑓𝑎) = exp [−𝑗 (Φ
𝑎(𝑓𝑎))] . (22)
(5) Perform azimuth IFFT to obtain a well-focused SARimage.
5. Simulations and Results
In this section, several examples are provided to illustrate theperformance of the proposed method. Because of the com-plex configuration, the high-order terms in the slant rangecannot be ignored. If inappropriately approximated, theimaging focusing resolution may be affected significantly.Some simulations are conducted to compare the influences ofkeeping the terms up to the quadratic term (quadratic rangemodel) and the higher order term (proposed range model).Parameters used in the simulations are listed in Table 1.The imaging results of center point and fringe point in theimaging area using the proposed range model are given inFigures 3 and 4. In order to confirm the necessity and validityusing the higher order range model in this special configu-ration, some simulations are also conducted to compare thedifferences using the quadratic rangemodel and the proposedrange model, and the results are shown in Figures 5 and 6(here, the center point is selected in comparison).
Figure 3 depicts the results of the center point usingthe proposed range model. Figure 3(a) is the 2D impulseresponse; Figures 3(b) and 3(c) are the azimuth impulseresponse and the range impulse response, respectively. The2D impulse response of the fringe target point using theproposed range model is shown in Figure 4(a), and theazimuth impulse response and the range impulse response aregiven in Figures 4(b) and 4(c), respectively. We can see fromFigures 3 and 4 that both center point and fringe point arewell focused in range direction and azimuth direction. For the
complexity of theMBFL-SAR configuration, if the slant rangeis not approximated accurately enough, the phase term in the2D frequency spectrum will not be compensated completelyin the azimuth direction. It is easy to find that the imageof the point target suffers from distortion and main-lobebroadening when the slant range keeps the terms up to thequadratic term in Figures 5(a) and 6(a). On the other hand, ifwe are using the proposed rangemodel, the imaging focusingperformance can be obviously improved, as given in Figures5(b) and 6(b). It is obvious that the image is well focusedin the azimuth direction, which confirms it necessary toapproximate appropriately in the MBFL-SAR configuration.
Table 2 lists the image quality parameters of the centerpoint and fringe point using the proposed method to furtherillustrate the validity of the proposed algorithm. PSLR andISLR represent peak side-lobe ratio and integrated side-loberatio, respectively. Besides, the theoretical PSLR and ISLR are−13.26 dB and−9.8 dB, respectively.We can see that the imagequality parameters of both the center point and fringe pointusing our proposed method are all close to the theoreticalones, which indicate satisfactory imaging results and furthervalidate the effectiveness and feasibility.
6. Conclusions
In this paper, we developed an imaging algorithm for MBFL-SAR configuration, a special MIMO radar mode.TheMBFL-SAR imaging geometric model is established and the signalmodel is analyzed firstly. The high-order term in the slantrange cannot be neglected because of the presence of highvelocity and acceleration and the addition of two square-root terms. Also, the difficulty in direct-using the POSP inthis configuration is discussed. Then 2D frequency spectrumis deduced using the method of series reversion based onthe appropriate approximation of the slant range. Based onthe derived spectrum, the corresponding imaging method is
8 International Journal of Antennas and Propagation
developed. The high-order term introduced from this con-figuration is compensated, together with range compression,at the beginning of the algorithm. RCMC is finished in therange time azimuth frequency domain as the range-variant 𝑘-coefficients.The focused SAR image can be obtained throughthe azimuth compression. The feasibility and efficiency ofthe proposed approach are validated with the simulationexperiments.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
Acknowledgments
This work was supported by the National Natural ScienceFoundation of China under Grants 61001211 and 61303035, bythe Fundamental Research Funds for the Central Universities(K5051202016), and by the Science Foundation forNavigation(20110181004).
References
[1] I. G. Cumming and F. H. Wong, Digital Processing of SyntheticAperture Radar Data: Algorithms and Implementation, ArtechHouse, Norwood, Mass, USA, 2005.
[2] D. L. Mensa, High Resolution Radar Cross-Section Imaging,Artech House, Boston, Mass, USA, 1991.
[3] S. A. Hovanessian, Introduction to Synthetic Array and ImagingRadar, Artech House, Norwood, Mass, USA, 1980.
[4] R. Kapoor, A. Banerjee, G. A. Tsihrintzis, andN.Nandhakumar,“UWB radar detection of targets in foliage using alpha-stableclutter models,” IEEE Transactions on Aerospace and ElectronicSystems, vol. 35, no. 3, pp. 819–834, 1999.
[5] G.Wang, X. Xia, andV. C. Chen, “Radar imaging ofmoving tar-gets in foliage using multifrequency multiaperture polarimetricSAR,” IEEE Transactions on Geoscience and Remote Sensing, vol.41, no. 8, pp. 1755–1764, 2003.
[6] E. Fishler, A. Haimovich, R. Blum,D. Chizhik, L. Cimini, and R.Valenzuela, “MIMO radar: An idea whose time has come,” inProceedings of the IEEE Radar Conference, pp. 71–78, April 2004.
[7] E. Fishler, A. Haimovich, R. Blum, L. Cimini, D. Chizhik, and R.Valenzuela, “Performance of MIMO radar systems: advantagesof angular diversity,” in Proceedings of the 38th Asilomar Confer-ence on Signals, Systems andComputers, pp. 305–309,November2004.
[8] R. Sharma, “Analysis of MIMO radar ambiguity functions andimplications on clear region,” in Proceedings of the IEEE Inter-national Radar Conference (RADAR ’10), pp. 544–548, Wash-ington, DC, USA, May 2010.
[9] J. Li and P. Stoica, MIMO Radar Signal Processing, Wiley, NewYork, NY, USA, 2009.
[10] W. Roberts, P. Stoica, J. Li, T. Yardibi, and F. A. Sadjadi, “Iterativeadaptive approaches to MIMO radar imaging,” IEEE Journal onSelected Topics in Signal Processing, vol. 4, no. 1, pp. 5–20, 2010.
[11] J. Li, G. Liao, and H. Griffiths, “Bistatic MIMO radar space-time adaptive processing,” in Proceedings of the IEEE RadarConference: in the Eye of the Storm (RadarCon ’11), pp. 498–501,Kansas, Mo, USA, May 2011.
[12] D.W. Bliss and K.W. Forsythe, “Multiple-inputmultiple-output(MIMO) radar and imaging: degrees of freedom and resolu-tion,” in Proceedings of the 37th Asilomar Conference on Signals,Systems and Computers, pp. 54–59, November 2003.
[13] I. Walterscheid, T. Espeter, J. Klare, A. R. Brenner, and J. H. G.Ender, “Potential and limitations of forward-looking bistaticSAR,” in Proceedings of the 30th IEEE International Geoscienceand Remote Sensing Symposium (IGARSS ’10), pp. 216–219, July2010.
[14] J. Wu, J. Yang, Y. Huang, H. Yang, and H. Wang, “Bistaticforward-looking SAR: theory and challenges,” in Proceedings ofthe IEEE Radar Conference (RADAR ’09), pp. 1–4, Pasadena,Calif, USA, May 2009.
[15] Z. Shi, H.Wang, P. Zhang, X. Tang, B.Wu, and C.Wang, “Studyon the probability of successful handoff of missile trajectoryfrommidcourse guidance to terminal guidance,” in Proceedingsof the International Conference on Computational and Informa-tion Sciences (ICCIS ’10), pp. 1005–1008, December 2010.
[16] Q. Zhao, X. Zhang, W. Song, and F. Lu, “Rotational analysis ofcertain terminal-guidance projectile,” in Proceedings of the 8thInternational Conference on Electronic Measurement and Instru-ments (ICEMI ’07), pp. 4415–4418, August 2007.
[17] C. Wu, “A digital system to produce imagery from SAR data,”in Proceedings of AIAA Conference on Systems Design Driven bySensors, October 1976.
[18] J. R. Bennett and I. G. Cumming, “A digital processor for theproduction of SEASAT synthetic aperture radar imagery,” inProceedings of Symposium on Machine Processing of RemotelySensed Data, June 1979.
[19] C. Wu, K. Y. Liu, and M. Y. Jin, “Modeling and a correlationalgorithm for spaceborne SAR signals,” IEEE Transactions onAerospace and Electronic Systems, vol. 18, no. 5, pp. 563–575,1982.
[20] R. K. Raney, H. Runge, R. Bamler, I. G. Cumming, and F. H.Wong, “Precision SAR processing using chirp scaling,” IEEETransactions on Geoscience and Remote Sensing, vol. 32, no. 4,pp. 786–799, 1994.
[21] M. Soumekh, “Bistatic synthetic aperture radar inversion withapplication in dynamic object imaging,” IEEE Transactions onSignal Processing, vol. 39, no. 9, pp. 2044–2055, 1991.
[22] M. Soumekh, “Wide-bandwidth continuous-wave monos-tatic/bistatic synthetic aperture radar imaging,” in Proceedingsof IEEE International Conference on Image Processing (ICIP ’98),vol. 3, pp. 361–365, IEEE, Chicago, Ill, USA, October 1998.
[23] M. Soumekh, J. Choi, and W. Zwolinski, “Target imaging usinga synthesized bistatic radar,” in Proceedings of the IEEE Inter-national Conference on Systems Engineering, pp. 39–42, August1989.
[24] Y. L. Neo, F. H. Wong, and I. G. Cumming, “Focusing bistaticSAR images using non-linear chirp scaling,” in Proceedings ofInternational Conference on Radar Systems, 2004.
[25] G.W. Davidson, I. G. Cumming, andM. R. Ito, “A chirp scalingapproach for processing squint mode SAR data,” IEEE Trans-actions on Aerospace and Electronic Systems, vol. 32, no. 1, pp.121–133, 1996.
[26] D. D’ Aria, A. M. Guarnieri, and F. Rocca, “Focusing bistaticsynthetic aperture radar using dipmove out,” IEEE Transactionson Geoscience and Remote Sensing, vol. 42, no. 7, pp. 1362–1376,2004.
[27] A. M. Guarnieri and F. Rocca, “Reduction to monostatic focus-ing of bistatic or motion uncompensated SAR surveys,” IEE
International Journal of Antennas and Propagation 9
Proceedings: Radar, Sonar and Navigation, vol. 153, no. 3, pp.199–207, 2006.
[28] Y. L. Neo, F. Wong, and I. G. Cumming, “A two-dimensionalspectrum for bistatic SAR processing using series reversion,”IEEE Geoscience and Remote Sensing Letters, vol. 4, no. 1, pp.93–96, 2007.
[29] Y. L. Neo, F. H. Wong, and I. G. Cumming, “Processing ofazimuth-invariant bistatic SAR data using the range doppleralgorithm,” IEEE Transactions on Geoscience and Remote Sens-ing, vol. 46, no. 1, pp. 14–21, 2008.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of