RTB-GL • Fits all Glocks® • Replaces factory rear sight • Includes all hardware for installation • Fits virtually all holsters • Dual Laser Modes 1 1 3 2 2 3 DANGER LASER LIGHT AVOID DIRECT EYE EXPOSURE POWER OUTPUT < 5mw WAVELENGTH 630-670mm CLASS IIIa PRODUCT ® 30 N. Alamos Dr. - Cottonwood, AZ 86326 Phone 928-649-3201 - Fax 928-649-3970 www.LaserLyte.com WARRANTY: Three Year Limited Warranty. Reset Process: Back-out both adjustment screws. Let laser sit for at least 10 minutes at room temperature (68°F/20°C). If, within 20 minutes, the laser is not pointing near the end the of slide, call customer service. 1 1 2 3 Battery Installation: (4) 377 2 3 Unscrew battery cap and remove batteries. Install new batteries. Screw in battery cap and tighten. Room Temp. (68°F/20°C) 10 min. 0˚ -10˚ 20˚ 40˚ 50˚ 60˚ 70˚ 80˚ 90˚ 100˚ 30˚ 10˚ 20˚ 30˚ 40˚ C F REV0912 U.S. Patent No: 8,006,428 7,997,023 ® ®
Transcript
RTB-GL
• Fits all Glocks®
• Replaces factory rear sight
• Includes all hardware for installation
• Fits virtually all holsters
• Dual Laser Modes
1
1 32
23
DANGER
LASER LIGHT AVOID DIRECT EYE EXPOSURE POWER OUTPUT < 5mw WAVELENGTH 630-670mm
CLASS IIIa PRODUCT
®
30 N. Alamos Dr. - Cottonwood, AZ 86326 Phone 928-649-3201 - Fax 928-649-3970
www.LaserLyte.com
WARRANTY: Three Year
Limited Warranty.
Reset Process: Back-out both adjustment screws. Let laser sit for at least 10 minutes at room temperature (68°F/20°C). If, within 20 minutes, the laser is not pointing near the end the of slide, call customer service.
1
1
23
Battery Installation: (4) 377
2
3
Unscrew battery cap and remove batteries. Install new batteries. Screw in battery cap and tighten.
Room Temp. (68°F/20°C)
10 min. 0˚
-10˚20˚
40˚50˚60˚70˚80˚90˚
100˚
30˚
10˚
20˚
30˚
40˚CF
REV0912
U.S. Patent No: 8,006,428 7,997,023
®
®
RTB_GL.indd 1 9/21/12 10:52 AM
Rear Sight Laser for all Glock® Models
Installation: UNLOAD YOUR FIREARM! Attach danger label to slide of gun near laser with arrow pointing toward front sight. Remove slide from frame, then remove spring and barrel. Remove rear sight from slide. With laser facing toward the front, start laser dove tail into the dove tail of the slide. Using provided brass punch, place narrow tip of punch onto flat surface of the laser dove tail.
Using a small hammer, tap punch until the laser is centered in the middle of the slide. Using the included .050 Allen wrench, tighten locking screw in the center of the laser.
12
3
4
5
6
7
8
RTB-GL3
1 2
4
86
5
.05 inch wrench
UNLOAD YOUR FIREARM!
yes
no
Attach danger label to slide of gun near laser with arrow pointing toward front sight.
7 yes
no
no
1
1 2 3
23
Activation: Press once turns laser on: constant or pulse. Press and hold for 5 seconds to change mode. Second press: turns laser off.
Auto-Off feature:• After 5 minutes in any mode, warning pulse will activate.• After 1 minute in warning pulse mode, laser will turn off.• Press the switch during warning pulse for laser reset.
5 min. 6 min. off
5 min.
3
4
12345
5 5
Laser Sight In: Assemble barrel and spring into slide and then install back onto gun.
Make sure your firearm is unloaded and always point in a safe direction. Use the provided .035 Allen wrench to adjust the sight. Always end adjustments on a clockwise turn. Make final adjustments at shooting range.
Moving Laser Dot
.035 inch wrench
up
down
right
left
Elevation Windage
or or5 sec.
1
123
Laser Sight In: Assemble weapon and make safe. Align front & rear sights by shining laser dot 21 ft (recommended) away in a safe direction. First! Use elevation screw to adjust laser dot .5 inch above front sight. Second! Use windage screw to adjust laser dot .5 inch left of front sight. Third! Use both screws in 1/4 turn increments to move dot above front sight. Make final adjustments at shooting range.
