Rev 1.7 Updated May.16/2016 Technical Manual & Parts Lists€¦ · 362 Industrial Park Drive...

362 Industrial Park Drive

Lawrenceville, GA 30046

770-963-7369 • www.atlatt.com

Technical Manual & Parts Lists

Model 1409 Rev 1.7 Updated May.16/2016

Technical Manual & Part List


Technical Manual & Part List Page 2

IMPORTANT

It is important to read and understand the information contained within this

manual before attempting to operate the machine. Atlanta Attachment Co., Inc.

shall not be held liable for damage resulting from misuse of the information

presented within, and reserves the right to change the information contained

within, without prior notification.

ATLANTA ATTACHMENT COMPANY, INC.

Confidential and Proprietary Information

The materials contained herein are confidential and proprietary information of Atlanta

Attachment Company. In addition to any confidentiality and non-disclosure obligations that currently

exist between you and Atlanta Attachment Company, your use of these materials serves as an

acknowledgment of the confidential and proprietary nature of these materials and your duty not to

make any unauthorized use or disclosure of these materials.

All materials contained herein are additionally protected by United States Copyright law and

may not be used, disclosed, reproduced, distributed, published or sold without the express written

consent of Atlanta Attachment Company, which consent may be withheld in Atlanta Attachment

Company’s sole discretion. You may not alter or remove any copyright, trademark or other notice from

copies of these materials.



Table of Contents

ATLANTA ATTACHMENT COMPANY, INC. ........................................................................................................... 2

CONFIDENTIAL AND PROPRIETARY INFORMATION ................................................................................................ 2

IMPORTANT SAFETY INSTRUCTION ........................................................................................................................ 6

MANDATORY INFORMATION ................................................................................................................................. 6

SCOPE OF THE INSTRUCTION MATERIAL ................................................................................................................ 6

INTENDED USE ....................................................................................................................................................... 6

EXCLUSION OF MISUSE .......................................................................................................................................... 7

LIABILITY ................................................................................................................................................................ 7

CHOICE AND QUALIFICATION OF PERSONNEL ........................................................................................................ 8

TRAINING............................................................................................................................................................... 8

RESPONSIBILITIES .................................................................................................................................................. 8

A WORD TO THE OPERATOR .................................................................................................................................. 9

SAFETY EQUIPMENT ON THE MACHINES................................................................................................................ 9

DAMAGE ................................................................................................................................................................ 9

FAULTS OR ERRORS ............................................................................................................................................. 10

SIGNS ON THE MACHINE ...................................................................................................................................... 10

PROTECTIVE EYEWEAR ......................................................................................................................................... 10

TOOLS .................................................................................................................................................................. 10

OILS, LUBRICANTS, CHEMICALS............................................................................................................................ 10

NO SMOKING, FIRE, EXPLOSION HAZARD ............................................................................................................ 10

WORKPLACE ........................................................................................................................................................ 11

EMERGENCY STOP ............................................................................................................................................... 11

FIRST AID ............................................................................................................................................................. 11

IMPORTANT NOTICES .......................................................................................................................................... 11

REPORTING AND FIGHTING FIRES ........................................................................................................................ 11

ELECTRICAL POWER SUPPLY ................................................................................................................................ 12

DELIVERY OF THE MACHINE/PACKAGING ............................................................................................................ 13

TRANSPORT DAMAGE .......................................................................................................................................... 13

INTERIM STORAGE ............................................................................................................................................... 13



TRANSPORTING THE MACHINE ............................................................................................................................ 13

WORKPLACE ENVIRONMENT ............................................................................................................................... 14

LOCAL REGULATIONS ........................................................................................................................................... 15

CONNECTION, RECONNECTION ............................................................................................................................ 15

ELECTRICAL CONNECTION .................................................................................................................................... 15

PNEUMATIC CONNECTION ................................................................................................................................... 15

MAINTENANCE .................................................................................................................................................... 15

GENERAL SAFETY INSTRUCTIONS ......................................................................................................................... 15

MAINTENANCE, CARE, ADJUSTMENT ................................................................................................................... 16

WASTE, DISASSEMBLY, DISPOSAL ........................................................................................................................ 16

REPAIR ................................................................................................................................................................. 16

REPLACEMENT PARTS .......................................................................................................................................... 16

REPAIR, ELECTRICAL ............................................................................................................................................. 16

VENTILATION/HAZARDOUS GASES ...................................................................................................................... 17

HYDRAULIC AND PNEUMATIC SYSTEMS............................................................................................................... 17

GENERAL LIABILITY .............................................................................................................................................. 17

STARTING MACHINE MOVEMENTS ...................................................................................................................... 18

A WORD TO THE END USER .................................................................................................................................. 18

GENERAL MACHINE DATA .................................................................................................................................... 18

ELECTRICAL & PNEUMATIC SPECIFICATIONS ........................................................................................................ 18

INSTALLATION & SETUP ....................................................................................................................................... 18

ADJUSTMENTS / CONTROLS ................................................................................................................................ 20

CONTROL PANEL FUNCTIONS ............................................................................................................................... 22

FOOT PEDAL FUNCTIONS ..................................................................................................................................... 22

OPERATING PROCEDURE ..................................................................................................................................... 23

TROUBLESHOOTING............................................................................................................................................. 25

BELT ADJUSTMENT .............................................................................................................................................. 26

GENERAL MACHINE MAINTENANCE ..................................................................................................................... 27

ASSEMBLY DRAWINGS & PARTS LISTS ................................................................................................................. 29

11409 UNBALER, ROUND BALES ..................................................................................................................... 31



1409330 FRAME W/REWINDER ........................................................................................................................... 33

1409 CONTROLS ASM .......................................................................................................................................... 35

1409229 FRAME ASSY. W/BACKSTOP .................................................................................................................. 37

1409247 REWINDER ARM .................................................................................................................................... 38

1409221 FRAME W/BELTS ................................................................................................................................... 40

1409311 GATE, BACK SKID ................................................................................................................................... 42

1409 SKID PLATE ASM .......................................................................................................................................... 43

1409197 LOWER CONVEYOR ASM ....................................................................................................................... 45

1409206 UPPER CONVEYOR ASM......................................................................................................................... 47

1409336 ELECTRICAL PANEL1409 ......................................................................................................................... 49

1409574 REWIND GUARD DOOR .................................................................................................................... 50

1409580 GATE SAFETY CONTROL .................................................................................................................. 51

1409586 GAS SPRING ASSEMBLY ................................................................................................................... 52

1409-PD PNEUMATIC DIAGRAM .......................................................................................................................... 53

1409-WD WIRING DIAGRAM................................................................................................................................ 54



Important Safety Instruction This part of the Instruction Material is provided for the safe use of your

equipment. It contains important information to help work safely with your

machine and describes the dangers inherent in machinery. Some of these

dangers are obvious, while others are less evident.

Mandatory Information

All persons working on the machine should read and understand all parts of the Safety

Instructions. This applies, in particular, for persons who only work on the machine occasionally

(e.g. for maintenance and repair). Persons who have difficulty reading must receive particularly

thorough instruction.

Scope of the Instruction Material

The Instruction Material comprises:

Safety information

Operator Instructions

Electrical and Pneumatic diagrams And may also include;

A list of recommended spare parts

Serial Bus Control system Operator instructions

Instruction Manual(s) for components made by other manufacturers

The layout and installation diagram containing information for installation

Intended Use

Our machines are designed and built in line with the state of the art and the accepted safety

rules. However, all machines may endanger the life and limb of their users and/or third parties

and be damaged or cause damage to other property, particularly if they are operated

incorrectly or used for purposes other than those specified in the Instruction Manual.



Exclusion of Misuse

Non-conforming uses include, for example, using the equipment for

something other than it was designed for, as well as operation without

duly installed safety equipment. The risk rests exclusively with the end

user.

Conforming use of the machine includes compliance with the technical data, information and

regulations in all parts of the complete Instruction Material, as well as compliance with the

maintenance regulations. All local safety and accident prevention regulations must also be

observed.

Liability

The machine should only be operated when in perfect working order, with due regard for safety

and the potential dangers, as well as in accordance with the Instruction Material. Faults and

malfunctions capable of impairing safety should be remedied immediately. We cannot accept

any liability for personal injury or property damage due to operator errors or non-compliance

with the safety instructions contained in this booklet. The risk rests exclusively with the end

user.

The Instruction Material should always be kept near the machine so that it is accessible to all

concerned.

The local, general, statutory and other binding regulations on accident prevention and

environmental protection must also be observed in addition to the Instruction Material. The

operating staff must be instructed accordingly. This obligation also includes the handling of

dangerous substances and provision/use of personal protective equipment.



The Instruction Material should be supplemented by instructions, including supervisory and

notification duties with due regard for special operational features, such as the organization of

work, work sequences, the personnel deployed, etc.

The personnel's awareness of the dangers and compliance with the safety regulations should be

checked at irregular intervals.

Choice and Qualification of Personnel

Ensure that work on the machine is only carried out by reliable persons who have been

appropriately trained for such work - either within the company, by our field staff or at our

office - and who have not only been duly appointed and authorized, but are also fully familiar

with the local regulations. Work on the machine should only be carried out by skilled personnel,

under the management and supervision of a duly qualified engineer.

This not only applies when the machine is used for production, but also for special work

associated with its operation (start-up and maintenance), especially when it concerns work on

the pneumatic or electrical systems, as well as on the software/serial bus system.

Training

Everyone working on or with the machine should be duly trained and informed with regard to

correct use of the safety equipment, the foreseeable dangers which may arise during operation

of the machine and the safety precautions to be taken. In addition, the personnel should be

instructed to check all safety mechanisms at regular intervals.

Responsibilities

Clearly define exactly who is responsible for operating, setting-up, servicing and repairing the

machine. Define the responsibilities of the machine operator and authorize him to refuse any

instructions by third parties if they run contrary to the machine's safety. This applies in

particular for the operators of machines linked to other equipment. Persons receiving training

of any kind may only work on or with the machine under the constant supervision of an

experienced operator. Note the minimum age limits permitted by law.



A Word to the Operator

The greatest danger inherent in our machines:

is that of fingers, hands or loose clothing being drawn into a machine by live, coasting or

rotating tools or assemblies or of being cut by sharp tools or burned by hot elements.

ALWAYS BE CONSCIOUS OF THESE DANGERS!

Safety Equipment on the Machines

All machines are delivered with safety equipment, which shall not be

removed or bypassed during operation.

The correct functioning of safety equipment on machines and systems

should be checked every day and before every new shift starts, after

maintenance and repair work, when starting up for the first time and when

restarting (e.g. after prolonged shutdowns).

If safety equipment has to be dismantled for setting-up, maintenance or repair work, such

safety equipment shall be replaced and checked immediately upon completing the

maintenance or repair work.

All protective mechanisms shall be fitted and fully operational whenever the machine is at a

standstill or if it has been shut down for a longer period of time.

Damage

If any changes capable of impairing safety are observed in the machine or its mode of

operation, such as malfunctions, faults or changes in the machine or tools, appropriate steps

must be taken immediately, the machine switched off and a proper lockout tagout procedure

followed. The machine should be examined for obvious damage and defects at least once per

shift. Damage found shall be immediately remedied by a duly authorized person before

resuming operation of machine.

The machine should only be operated when in perfect working order and when all protective

mechanisms and safety equipment, such as detachable protective mechanisms, emergency

STOP systems, etc. are in place and operational.



Faults or Errors

The machine must be switched off and all moving or rotating parts allowed to come to a

standstill and secured against accidental restart before starting to remedy any faults or errors.

Signs on the Machine

Safety and danger signs on the machine should be observed and checked at regular intervals to

ensure that they are complete and undamaged. They should be clearly visible and legible at all

times.

Clothing, Jewelry, Protective Equipment

Long loose hair, loose-fitting clothes, gloves and jewelry, including rings, should be avoided in

order to avoid injuries due to being caught, drawn in and wound up inside the machine.

Protective Eyewear

Protective eyewear that has been tested by the local authorities should be

worn whenever there is a possibility of loose or flying objects or particles

such as when cleaning the machine with compressed air.

Tools

Always count the number of tools in your possession before starting work on the machine. This

will allow you to check that no tools have been left behind inside the machine. Never leave a

tool in the machine while working.

Oils, Lubricants, Chemicals

Note the applicable safety regulations for the product used.

No Smoking, Fire, Explosion Hazard

Smoking and open flame (e.g. welding work) should be prohibited in the production area due to

the risk of fire and explosions.



Workplace

A clear working area without any obstructions whatsoever is essential for safe operation of the

machine. The floor should be level and clean, without any waste.

The workplace should be well lit, either by the general lighting or by local lights.

Emergency STOP

The emergency STOP buttons bring all machine movements to a standstill. Make sure you know

exactly where they are located and how they work. Try them out. Always ensure easy access to

the nearest emergency STOP button while working on the machine.

First Aid 1. Keep calm even when injured. 2. Clear the operator from the danger zone. The decision of what to do and whether to

seek additional assistance rests entirely with you, particularly if someone has been trapped.

3. Give First Aid. Special courses are offered by such organizations as the employers' liability insurance association. Your colleagues should be able to rely on you and vice versa.

4. Call an ambulance. Do you know the telephone numbers for the ambulance service, police and fire service?

Important Notices

Reporting and Fighting Fires

Read the instructions posted in the factory with regard to reporting fires and the emergency

exits. Make sure you know exactly where the fire extinguishers and sprinkler systems are

located and how they are operated. Pass on the corresponding information to the firemen

when they arrive. Ensure there are enough signs to avoid fire hazards.

The following fire extinguishers may be used:

- Dry powder extinguishers, ABC fire-extinguishing powder.



- Carbon dioxide fire extinguishers to DIN 14461 for electronic components. Great care must be

exercised when using carbon dioxide fire extinguishers in confined, badly ventilated rooms (see

DIN 14406 and 14270).

Isolate the machine from the power supply if a fire breaks out. Do not use water on burning

electrical parts until it is absolutely certain that they have been completely disconnected from

the power supply. Burning oils, lubricants, plastics and coatings on the machine can give off

gases and vapors that may be harmful to your health.

A qualified person should be consulted to repair the damage after a fire.

Electrical Power Supply

Before undertaking any maintenance or repair work on the machine,

switch off the electrical power to the machine at the main source and

secure it with a padlock so that it cannot be switched on again without

authorization.

In practice, this may mean that the technician, electrician and operator all attach their own

padlock to the master switch simultaneously so that they can carry out their work safely.

Locking extension plates should be available for multiple locks if required. The primary purpose

for a lockout/tagout procedure is to protect workers from injury caused by unexpected

energizing or start-up of equipment.

Energy sources (electrical/pneumatic/hydraulic, etc.) for the equipment shall be turned off or

disconnected and the switches locked or labeled with a warning tag. It is the responsibility of

the employer to establish control procedures. Follow lockout/tagout procedures before set-up

and/or any service or maintenance work is performed, including lubrication, cleaning or

clearance of jams.

Caution: The machine is still not completely de-energized even when the master

switch is off.

- Electricity - The machine is always isolated from the electrical power supply whenever the

master switch has been switched off. However, this does not apply for the power supply in the

control cabinet, nor for equipment that does not draw its power via the master switch.



- Pneumatic / hydraulic energy - Almost all our machines carry compressed air. In addition to

switching off the master switch, the air supply must also be disconnected and the machine

checked to ensure it is depressurized before starting any work on the machine; otherwise the

machine may execute uncontrolled movements.

- Kinetic energy - Note that some motors or spindles, for example, may continue to run or coast

run on after being switched off.

- Potential energy - Individual assemblies may need to be secured if necessary for repair work.

Delivery of the Machine/Packaging

Note any markings on the packaging, such as weights, lifting points and special information.

Avoid temperature fluctuations. Condensation may damage the machine.

Transport Damage

The packaging and machine must immediately be examined for signs of damage in transit. Such

damage must be reported to the shipper/transporter within the applicable time limits. Contact

us and/or your transport insurer without delay. Never operate a damaged machine.

Interim Storage

If the machine has to be stored temporarily, it must be oiled or greased and stored in a dry

place where it is protected from the weather in order to avoid damage. A corrosion-inhibiting

coating should be applied if the machine has to be stored for a longer period of time and

additional precautions taken to avoid corrosion.

Transporting the Machine

Disconnect the machine from all external connections and secure any loose assemblies or parts.

Never step under a suspended load. When transporting the machine or assemblies in a crate,

ensure that the ropes or arms of a forklift truck are positioned as close to the edge of the crate

as possible. The center of gravity is not necessarily in the middle of the crate. Note the accident

prevention regulations, safety instructions and local regulations governing transport of the

machine and its assemblies.



Only use suitable transport vehicles, hoisting gear and load suspension devices that are in

perfect working order and of adequate carrying capacity. Transport should only be entrusted to

duly qualified personnel.

Never allow the straps to rest against the machine enclosure and never push or pull sensitive

parts of the machine. Ensure that the load is always properly secured. Before or immediately

after loading the machine, secure it properly and affix corresponding warnings.

All transport guards and lifting devices must be removed before the machine is started up

again. Any parts that are to be removed for transport must be carefully refitted and secured

before the machine is started up again.

Workplace Environment

Our machines are designed for use in enclosed rooms:

Permissible ambient temperature approx. 5 - 40 °C (40 - 104 °F). Malfunctions of the control

systems and uncontrolled machine movements may occur at temperatures outside this range.

Protect against climatic influences, such as electrostatic charges, lightning strikes, hail, storm

damage, high humidity, salinity of the air in coastal regions.

Protect against influences from the surroundings: no structure-borne vibrations, no grinding

dust, or chemical vapors.

Protect against unauthorized access.

Ensure that the machine and accessories are set up in a stable position.

Ensure easy access for operation and maintenance (Instruction Manual and layout diagram);

also verify that the floor is strong enough to carry the weight of the machine.

Machine Installation

This equipment must be installed by an Atlanta Attachment Co. technician, or by a properly

trained and authorized technician/mechanic. Atlanta Attachment Co. reserves the right to void

any machine warranty if the machine is installed by anyone other than a qualified person as

stated above



Local Regulations

Particular attention must be paid to local and statutory regulations, etc. when installing

machines and the plant (e.g. with regard to the specified escape routes). Note the safety zones

in relation to adjacent machines.

Connection, Reconnection

Energy feed and discharge lines must be routed so that they do not run through the operator's

working area, are not compressed, crushed or buckled, are not subjected to tensile stresses and

cannot rub against anything. This is particularly important in the case of pneumatic, hydraulic

and electricity lines or hoses. Always take the machine movements into account when routing

such lines.

Electrical Connection

The machine shall only be connected to the factory power supply by a qualified electrician who

is familiar with the local regulations. Before switching on the master switch, check that all

fasteners are secure.

Pneumatic Connection

Only use dry filtered compressed air. Ensure that the air pressure always remains within the

range specified, otherwise malfunctions may occur.

Maintenance

General Safety Instructions

The machine shall be switched off, come to a standstill and be secured so that it cannot be

switched on again inadvertently before starting any maintenance work whatsoever. Use proper

lockout/tagout procedures to secure the machine against inadvertent startup.

Remove any oil, grease, dirt and waste from the machine, particularly from the connections and

screws, when starting the maintenance and/or repair work. Do not use any corrosive-cleaning

agents. Use lint-free rags.



Retighten all screw connections that have to be loosened for the maintenance and repair work.

Any safety mechanisms that have to be dismantled for setting-up, maintenance or repair

purposes must be refitted and checked immediately after completing the work.

Maintenance, Care, Adjustment

The activities and intervals specified in the Instruction Manual for carrying out adjustments,

maintenance and inspections must be observed and parts replaced as specified.

All hydraulic and pneumatic lines should be examined for leaks, loose connections, rubbing and

damage whenever the machine is serviced. Any defects found must be remedied immediately.

Waste, Disassembly, Disposal

Waste products should be cleared from the machine as soon as possible as not to create a fire

hazard.

Ensure that fuels and operating lubricants, as well as replacement parts are disposed of in a

safe and ecologically acceptable manner. Note the local regulations on pollution control.

When scrapping (disassembling) the machine and its assemblies, ensure that these materials

are disposed of safely. Either commission a specialist company familiar with the local

regulations or note the local regulations when disposing of these materials yourself. Materials

should be sorted properly.

Repair

Replacement Parts

We cannot accept any liability whatsoever for damage due to the use of parts made by other

manufacturers or due to unqualified repair or modification of the machine.

Repair, Electrical

The power supply must be switched off (master switch off) and secured so that it cannot be

switched on again inadvertently before starting any work on live parts.



Those parts of the machine and plant on which inspection, maintenance or repair work is to be

carried out must be isolated from the power supply, if specified. The isolated parts must first be

checked to determine that they are truly de-energized before being grounded and short-

circuited. Adjacent live parts must also be isolated.

The protective measures implemented (e.g. grounding resistance) must be tested before

restarting the machine after all assembly or repair work on electric parts.

Signal generators (limit switches) and other electrical parts on the safety mechanisms must not

be removed or bypassed. Only use original fuses or circuit overloads with the specified current

rating. The machine must be switched off immediately if a fault develops in the electrical power

supply.

The electrical equipment of our machines must be checked at regular intervals and any defects

found must be remedied immediately.

If it is necessary to carry out work on live parts, a second person should be on hand to operate

the emergency OFF switch or master switch with voltage release in the event of an emergency.

The working area should be cordoned off and marked by a warning sign. Only use electrically

insulated tools.

Ventilation/Hazardous Gases

It is the end users responsibility to ensure adequate ventilation is provided to exhaust any and

all noxious or hazardous gases that may be present in the working environment.

Hydraulic and Pneumatic Systems

Work on hydraulic or pneumatic equipment shall only be carried out by persons with training,

knowledge and experience of hydraulic systems. Pressure lines shall be depressurized before

starting any repair work.

General Liability

Liability for machine damage and personal injury is extinguished completely if any unauthorized

conversions or modifications are undertaken. The machine must not be modified, enlarged or

converted in any way capable of affecting safety without the manufacturer's prior approval.



Starting Machine Movements

Read the Instruction Manual carefully to establish which keys and functions start machine

movements.

A Word to the End User The end user has sole responsibility to enforce the use of safety procedures and guards on the

machine. Any other safety devices or procedures due to local regulations should be should be

retrofitted in accordance to these regulations and/or the EC Directive on the safety of

machines.

Operator’s position must always be readily accessible. Escape routes must always be kept clear

and safety areas should be identified.

General Machine Data

Electrical & Pneumatic Specifications

Electrical: 220 VAC, 20 amp, 50/60 Hz Single Phase

Pneumatic: 80 PSI, 5 SCFM avg. (3/8” Airline).

Set the MAIN regulator to 70 PSI

Installation & Setup

1. Remove all packing material (bubble wrap, foam padding, etc.). 2. Position the machine in a desired location on a sound and reasonably level floor.



3. Make sure that there is sufficient lighting over the machine. 4. Clean the machine of any dust that may have accumulated during shipping. 5. Make required electric and pneumatic connections using only appropriate connectors.

Make sure the voltage has been set correctly. 6. Plug the Foot Pedal assembly into it’s cable (inside right panel door). Plug connectors in

access slot in front of machine.



Adjustments / Controls

Control Panel – This panel of buttons allows operator to activate machine, stop the

machine in case of emergency, change direction of the motion of the belts, manual jog,

open and close the door, and adjust speed of the belts.

Foot Pedals – The foot pedal assembly has two pedals. The left is the Run pedal which

toggles the machine into a continuous unload mode. The other is the Jog pedal which is a

momentary switch and jogs the machine in high speed and will typically be used at the start

and finish of a roll to wind excess wrap.



Accumulator slip clutch – Located underneath accumulator guard, tighten or loosen the nut

to adjust the amount of tension the accumulator applies to the material wrap.

Pressure regulator – This controls the air pressure supplied to the air cylinder used to open

and close the door.



Control Panel Functions

1. Emergency Stop Button – Pressing this button will turn power off to the machine. This

button will lock when pressed. Twisting this button will cause it to unlock and return to

its normal position.

2. Power on button – Pressing this button will energize the machine. It is lighted and will

indicate when the machine has power.

3. Forward/Reverse Switch – This switch controls the direction the belts turn. Forward is

the normal operating direction.

4. Jog button – This button is a momentary manual jog. This differs from the foot pedal jog

because it drives the belts at the slower “Run” speed.

5. Lockout – This switch connects main power to the machine and needs to be on for the

machine to operate. It is capable of being locked for a lock-out tag-out procedure.

6. Safety indicator – This is a light that indicates when any door or guard is open or ajar. If

this light is activated the machine will not run or will stop running.

7. Door open/close – This switch will open and close the back door to allow loading of

bales. It is to remain in the close position unless being loaded.

CAUTION: This door will close at power loss.

8. Speed – The speed control knob controls the continuous unload mode run speed and

the yellow push button jog speed.

Foot Pedal Functions

1. Run – The run pedal is a toggle switch to operate the machine in a continuous unload

mode. Activating once will start unload operation. Activating a second time will stop the

unload operation. The speed is set with the speed knob.

2. Jog – The jog pedal is a momentary pedal which has to be held down to operate. It

operates the machine at high speed and is used in the beginning and ending of

operation to feed out the excess wrapping material.



Operating procedure 1. Open (raise) the rear door using the Door Open/Close switch.

2. Roll the bale of springs into the machine so it will unwrap from the top. If the bale is

wrapped with plastic, spray lightly with silicone spray before loading into machine.

3. Close (lower) the door.

4. Using the Jog pedal, Jog the machine to position the leading edge of material wrap at

the exit opening.

5. Cut any shrink wrap or straps and remove any loose material if possible.



CAUTION: Roll may expand unexpectedly when bands/wrap are cut.

6. Jog the machine again, holding the leading edge of wrap, and feed out approximately 5-

6 feet of wrap. Remove any loose material.

7. Open the accumulator front guard door, pull the end of the wrap between the

accumulator bars, the loose end should hang down a foot or two, close the guard door.

8. Jog the machine more until the first spring is exposed.

9. Activate the Run pedal to start the continuous unload mode

10. Adjust the run speed control as desired.

11. With two people, remove the springs and stack.

12. You may stop the continuous mode any time by pressing the Run pedal again.

13. When all the springs are removed, press the Run pedal to stop the continuous cycle.

Hold down the Jog pedal to rewind all the rest of the wrap onto the accumulator.

14. Go to opposite side of machine, unlatch the end guard door on the accumulator and

swing it out of the way. Pull out the wrapping material. Open the front accumulator

guard door and, while supporting the rods in place, close the end door so the rods

engage the support spindle. Latch the end door and close the front accumulator guard

door.



15. Repeat for next bale.

Troubleshooting

Machine doesn’t run when foot pedal depressed

1. Verify power is on and pedal is connected.

2. Check e-stop is unlatched.

3. Check safety lamp indicating open doors or guards.

4. Check that foot pedal cable is plugged in.

5. Turn off main power, wait 10 seconds, re-apply power and try again (This

resets the VFW drive that runs the motor.)

Gate will not close

Check material roll is not interfering with closing of door.

Motor runs but belts do not turn

Check if belt is slipping on drive roller, tighten slightly if necessary.



Belt Adjustment

As belts wear in adjustments may be necessary to maintain proper tracking. If a belt is tracking

to one side adjustment may be made while machine is empty by opening the gate then doing

one of the following:

If belt is tight:

1. Go to the side which the belt is moving toward.

2. Loosen the lock nut on the belt tensioning screw.

3. Turn belt tensioning screw counter clockwise 1/2 of a turn to reduce belt

tension.

4. Retighten lock nut on belt tensioning screw.

5. Run belts while machine is not loaded. Monitor belt tracking, the adjusted belt

should maintain a consistent position.

6. Continue unloading springs and monitoring belt tracking.

7. Readjust belt tension as necessary until proper tracking is achieved.

If the belt is loose:

1. Go to the opposite side which the belt is moving toward.

2. Loosen the lock nut on the belt tensioning screw.

3. Turn belt tensioning screw clockwise between 1/2 of a turn to increase belt

tension.

4. Retighten lock nut on belt tensioning screw.

5. Run belts while machine is not loaded. Monitor belt tracking, the adjusted belt

should maintain a consistent position.

6. Continue unloading springs and monitoring belt tracking.

7. Readjust belt tension as necessary until proper tracking is achieved.

During operation the belts may show a slight amount of twist which is normal. The overall

width of the belts is wider than the end rollers. In normal operation the inner rib of one side of

the belt will contact the edge of the end rollers. If a belt starts to tracking to one side and the

rib starts to climb onto the roller immediately stop operation and run the machine in reverse

until the belt returns to the appropriate position. Adjust the belt tension as stated above.



General Machine Maintenance

Daily (8-10 hrs. of operation)

Clean machine of any wrapping debris with an air blower.

Use silicone lubricant on inside of gate and front skid plate as necessary if springs are

wrapped with shrink wrap.

Weekly

Drain water from regulator trap.

Apply slight amount of oil to cylinder rods.

Monthly

Check chains and belts for tightness and wear.





Assembly Drawings & Parts Lists The materials contained herein are confidential and proprietary information of Atlanta Attachment

Company. In addition to any confidentiality and non-disclosure obligations that currently exist between

you and Atlanta Attachment Company, your use of these materials serves as an acknowledgment of the

confidential and proprietary nature of these materials and your duty not to make any unauthorized use

or disclosure of these materials.





11409 UNBALER, ROUND BALES ACC Drawing Number 9004829 Rev.11

NO QTY PART # DESCRIPTION NO QTY PART # DESCRIPTION

1 1 1278-6160H DUAL FOOT PEDAL ASSY 38 2 1409593 INSIDE GUARD, TOP

2 1 1409-WD DIAGRAM, WIRING 39 1 AA198-5110 FILTER/REGULATOR/LOCKOUT

3 1 1409-WD1 DIAGRAM, WIRING,1409518 40 1 AAE513C120 VALVE, 1/4",24VDC,CNTR BK

4 1 1409330 FRAME W/ REWINDER 41 1 AAFAN300- MUFFLER,3/8NPT,PLASTIC

5 1 1409344 CHAIN COVER, UPPER 42 2 AAQME-4-4 ELBOW, MALE,1/4X1/4NPT

6 1 1409345 CHAIN GUARD, LOWER 43 1 EEGLLA01B SWITCH,LIMIT,TOP PLUNGER

7 1 1409346 UPPER GUARD, SLIDING 44 2 EESB-375-4 HEYCO BUSHING 1/4" ID

8 1 1409347 UPPER GUARD, SLIDING 45 1 FF3200 STRAIN RELIEF,1/2NPT

9 1 1409376 DOOR, LEFT 46 1 FF8463 NUT,LOCK,1/2NPT,NYLON,BLK

10 1 1409378 DOOR, LEFT 47 1 FFM4518 STRAIN RELIEF,LIQ TIGHT

11 1 1409388 SENSOR BLOCK 48 2 MM1676A12 MAGNETIC CATCH

12 1 1409402 GUARD, GEAR RACK, RIGHT 49 3 MM9600K22 GROMMET,RUBBER,1/2 ID

13 1 1409408 GUARD, GEAR RACK, LEFT 50 2 MMELH-1 LATCH, 1/4 TURN, SLOTTED

14 1 1409410 SKID PLATE, ROLL 51 12 NNK10-32 KEP NUT, 10-32

15 1 1409440 SIDE GUARD, RIGHT 52 22 SSBC98024 10-32 X 3/8 BUTTON CAP SC

16 1 1409441 SIDE GUARD, LEFT 53 12 SSBC98032 10-32 X 1/2 BUTTON CAP SC

17 1 1409446 GUARD, GEAR RACK, LEFT 54 6 SSFC01024 1/4-20 X 3/8 FLAT CAP

18 1 1409451 TUBE, GUARD UPPER 55 12 SSFC90016 8-32 X 1/4 FL ALN CAP

19 1 1409452 BELT GUARD, RIGHT 56 6 SSHC01024 1/4-20 X 3/8 HHCS

20 1 1409453 BELT GUARD, LEFT 57 4 SSHC01040 1/4-20 X 5/8 HHCS

21 2 1409454 TAB, UPPER BELT GUARD 58 8 SSHC05032 1/4-28 X 1/2 HEX CAP

22 1 1409455 GUARD, GEAR RACK, RIGHT 59 8 SSHC25080 3/8-16 X 1-1/4 HHCS

23 1 1409460 DOOR, LEFT SIDE 60 12 SSHC98032 10-32X1/2 HEX HD

24 1 1409461 SMALL GUARD, LEFT 61 19 SSPP98024 10-32 X 3/8 PAN HD PHILIP

25 3 1409464 BUMPER ASSEMBLY 62 4 SSSC35064 SCREW, SOC CAP 3/8-24 x 1

26 1 1409473 TOE GUARD 63 2 SSSC70064 4-40 X 1 SOCKET CAP

27 1 1409516 STOP BUTTON BOX ASSY 64 8 SSSC80016 6-32 X 1/4 SOC CAP SC

28 1 1409518 CONTROL ASSEMBLY 65 18 SSZH#10032 SCREW,SHT.METAL HEX 10

29 1 1409551 BRACKET, BELT GUIDE 66 6 SSZH#10048 SCREW,SHT.METAL HEX 10

30 1 1409552 BRACKET, BELT ALIGNMENT 67 6 SSZS93032 SCREW, SHT.METAL 10 ZIP

31 1 1409567 GUARD, CHAIN, FRONT 68 6 WWF1/4 WASHER, FLAT, 1/4", COM

32 1 1409568 COVER, CHAIN, REAR 69 2 WWF4 WASHER, FLAT, #4

33 1 1409574 REWIND GUARD DOOR 70 50 WWF10 WASHER, FLAT, #10, COM

34 1 1409585 LIMIT SW ASSY 71 18 WWL1/4 WASHER,LOCK, 1/4

35 1 1409586 GAS SPRING ASSY 72 12 WWL3/8 WASHER,LOCK, 3/8

36 1 1409587 GATE CONTROL SWITCH ASSY 73 2 WWL4 WASHER,LOCK,#4

37 1 1409604 LIMIT SW ASSY, LEFT GATE 74 40 WWL10 WASHER,LOCK,#10





1409330 FRAME W/REWINDER ACC Drawing Number 1409330 Rev.4

NO QTY PART # DESCRIPTION

1 2 1388558 BOX, SAFETY SENSOR, DOOR

2 1 1409243 REWINDER

3 1 1409247 REWINDER ARM

4 1 1409259 KEYED SHAFT, COUPLING ARM

5 1 1409353 REWINDER COVER

6 1 1409354 FRAME, REWINDER GUARD

7 1 1409384 TORQUE LIMIT ASSY

8 1 1409472 REWINDER COVER, LEFT

9 1 1409542 KEY, 6MM SQ X 1.75L

10 1 EEGLLA01B SWITCH,LIMIT,TOP PLUNGER

11 1 FF8463 NUT,LOCK,1/2NPT,NYLON,BLK

12 2 FFE6930A SWITCH,INTEROCK,DOOR,SPDT

13 1 FFM4518 STRAIN RELIEF,LIQ TIGHT

14 1 MM331 CLAMP, PULL ACTION, 700LB

15 4 MMUCP205-16 BEARING,PILLOW BLOCK,1"

16 9 SSHC01040 1/4-20 X 5/8 HHCS

17 8 SSHC25080 3/8-16 X 1-1/4 HEX CAP

18 4 SSHC90032 #8-32 X 1/2 HEX CAP

19 6 SSHC98032 10-32X1/2 HEX HD

20 2 SSSC01024 1/4-20 X 3/8 SOC CAP SC

21 2 SSSC90080 #8-32 X 1-1/4 SOC CAP SC

22 4 SSSC98024 10-32 X 3/8 SOC CAP

23 7 SSZH#10032 SCREW,SHT.METAL HEX 10

24 5 WWF1/4 WASHER, FLAT, 1/4", COM

25 8 WWF3/8 WASHER,FLAT,3/8 OR 10MM

26 4 WWF8 WASHER, FLAT, #8

27 4 WWF10 WASHER, FLAT, #10, COM

28 6 WWFS10 WASHER, FLAT, #10, SAE

29 9 WWL1/4 WASHER,LOCK,1/4

30 8 WWL3/8 WASHER,LOCK, 3/8

31 6 WWL8 WASHER,LOCK,#8


33 1 1409229 FRAME ASSY, W/ BACKSTOP





1409 CONTROLS ASM Drawing Number 1409382 Rev.3


1 1 1409-LAB LABEL, 1409

2 1 1409381 CONTROLS PLATE

3 3 EE3X01 BLOCK,P.B. CONTACT, N.C.

4 3 EE3X10 BLOCK,P.B. CONTACT, N.O.

5 1 EE15Y PLATE, LEGEND, YELLOW

6 1 EE194EE631753 63AMP DISCON

7 1 EE194EE63PE GROUND TERMINAL

8 1 EE194LHE6N175 DISCONNECT HANDLE,RED/YEL

9 5 EEA3L LATCH,PUSH BUTTON

10 2 EED7N141 LAMP, INCONDES,12VAC/DC

11 2 EED53D0 BLOCK, LAMP, 22MM P.B.

12 1 EEPF5 BUTTON,PUSH,22MM,YELL,MO

13 1 EEPLE3 BUTTON, PUSH, GRN, ILLUM

14 1 EEPLE4 BUTTON, PUSH, RED, ILLUM

15 1 EEPMTS44 E-STOP BUTTON, TWIST REL.

16 1 FF274-416 KNOB,SPEED CONTROL

17 1 FFRPOT10K POTENTIOMETER,10K

18 1 MM800EPSM22 SWITCH, 2 POS SELECTOR





1409229 FRAME ASSY. W/BACKSTOP ACC Drawing Number 1409229 Rev.3


1 1 1409221 FRAME W/ BELTS

2 2 1409222 GEAR RACK, 10DP, 1" FACE

3 1 1409311 GATE, BACK SKID

4 1 1409421 WELDMENT, SHAFT MOUNT

5 1 1409450 SKID PLATE ASM

6 1 1409458 WELDMENT, SHAFT MOUNT, L

7 4 AA198RA404U FLOW CONTROL,1/4PTX1/4

8 2 AACDNC50900PPV CYLINDER, AIR,ISO,50X500

9 2 AAFSGSM16x15 BEARING,ROD END, FOR DNCB50

10 2 AAFSNC50 FLANGE, SWIVEL, FOR DNCB50

11 4 CCCL10F CLAMP COLLAR- 5/8 ID

12 12 SSFC01032 1/4-20 X 1/2 FLAT ALN CAP

13 8 SSHC20056 5/16-24 X 7/8 HEX CAP

14 4 SSSC25048 3/8-16X3/4 SOC CAP

15 8 WWF5/16 WASHER,FLAT,5/16




1409247 REWINDER ARM ACC Drawing Number 1409247 Rev.1


1 1 1409246 REWINDER COUPLING

2 2 1409248 REWINDER ARM BAR

3 1 1409252 SHAFT BLOCK, KEYED

4 1 1409256 SKID BLOCK

5 1 1409257 SPACER BLOCK, ARM

6 1 1409391 REWINDER GUARD

7 2 bbvf2s-110 BRG,FLG BLK,5/8 B,2 BLT

8 8 SSFC01064 1/4-20 X 1 FLAT CAP

9 2 SSFC98024 #10-32 X .375 FLAT CAP

10 4 SSHC25064 3/8-16 X 1 HHCS

11 1 TTK32315 KNOB,1-7/8OD,3/8B,BLACK






1409221 FRAME W/BELTS ACC Drawing Number 1409221 Rev.2

NO QTY PART # DESCRIPTION1 2 1306381 MOUNT,PLATE,MAIN DRIVE2 1 1409197 LOWER CONVEYOR ASM3 1 1409206 UPPER CONVEYOR ASM.4 1 1409323 1409 FRAME5 1 1409328 MAIN CROSS TUBE, GUARD6 1 1409393 5/16 KEY 2.2 L7 1 1409520 CHAIN ASSEMBLIES8 1 MM90L4B5 MOTOR,1.5KW,IEC,B5,2HP9 1 MMH4024-1-3_8 #40 SPROCKET 24T 1-3_8B

10 1 MMIC8030D90 GEARBOX,WORM,RV80,30:111 4 SSHC01096 1/4-20 X 1-1/2 HHCS12 24 SSHC25064 3/8-16 X 1 HHCS13 4 SSHC45128 1/2-13X2 HEX CAP14 4 WWFS1/4 WASHER,FLAT,SAE,1/415 4 WWL1/2 1/2 LOCK WASHER16 4 WWL1/4 WASHER,LOCK,1/417 24 WWL3/8 WASHER,LOCK, 3/8





1409311 GATE, BACK SKID ACC Drawing Number 1409311 Rev.3

NO QTY PART # DESCRIPTION1 1 1306082 COUPLING,2-PIECE,1" BORE

2 1 1409283 BACK SKID WELDMENT

3 1 1409312 SHAFT, TRANSFER, SHORT,

4 1 1409313 SHAFT, TRANSFER, 1409

5 2 1409398 1/4X1.375 KEY

6 4 1409515 FENDER WASHER,.45 ID,

7 4 MMCCF1CSS CAM FOLLOWER 1DIA CROWNED

8 2 MMNSS10F24-1M GEAR,SPUR,10P,1 B W/KEY

9 3 MMVPLS-116 BEARING,PILLOW BLOCK 1.0B

10 6 SSHC20064 5/16-24 X 1 HEX CAP

11 8 SSSS05016 1/4-28 X 1/4 SOC SET SC

12 6 WWF5/16 WASHER,FLAT,5/16




1409 SKID PLATE ASM ACC Drawing Number 1409450 Rev. 0

NO QTY PART # DESCRIPTION1 1 1409073 ROLLER, UNBAILER2 1 1409434 BACK SKID WELDMENT3 1 1409435 OUTFEED PLATE, LEFT4 1 1409436 OUTFEED PLATE, RIGHT5 2 BBFHSLF204-12G BEARING, FLANGE, 3/4" ID





1409197 LOWER CONVEYOR ASM ACC Drawing Number 1409197 Rev.9


1 1 1409191 BELT, CONVEYOR, LOWER

2 1 1409192 FRAME, CONVEYOR, LOWER

3 1 1409233 MOUNT WLDMT, NON DRV SIDE

4 1 1409343 MOUNT SUPPORT WLDMNT

5 1 1409392 KEY, .25 SQ X 2.81

6 2 1409405 ROLLER, BELT, MIDDLE

7 1 1409466 MOUNT, BEARING, BR TL

8 2 1409467 SCREW,BELT TENSION,5/8-18

9 1 1409469 MOUNT, BEARING, BL TR

10 4 1409471 BRNG MOD,FLANGE,1",2 BLT

11 2 1409521 SPROCKET,#40,24T,1.25"B

12 1 1409551 BRACKET, BELT GUIDE

13 1 1409552 BRACKET, BELT ALIGNMENT

14 1 1409557 SPROCKET,#40,24T,2.0B

15 1 1409563 KEY, .25 SQ X 0.9375

16 1 1409564 KEY, 1/2 x 0.9375

17 1 1409565 CHAIN, NO40, 54.5"

18 1 1409566 TENSIONER ASSEMBLY

19 2 1409570 BLOCK, BELT TENSION

20 1 1409594 RUBBER ROLLER ASSY

21 1 1409598 RUBBER ROLLER ASSEMBLY

22 2 MMUCPA209-28 BEARING,PILLOW BLOCK,1.25

23 2 NNJ5/8-18 NUT-HEX JAM 5/8-18

24 8 SSHC25096 3/8-16 X 1 1/2 HHCS

25 8 SSHC45080 1/2-13X1-1/4 HEX CAP

26 7 SSHC45096 1/2-13X1-1/2 HEX CAP

27 2 SSHC45112 1/2-13 X 1-3/4 HHCS, G8

28 8 SSSC25080 3/8-16X1-3/8 SOC CAP

29 4 SSSC45064 SCREW,SOC CAP,1/2-13 X 1"

30 2 SSSS01024 SCREW, SET, 1/4-20 X 3/8

31 2 UUCFC206-20 BEARING,FLANGE,1.25B,4 BOLT

32 17 WWL1/2 1/2 LOCK WASHER






1409206 UPPER CONVEYOR ASM ACC Drawing Number 1409206 Rev.8


1 1 1409191 BELT, CONVEYOR, LOWER

2 1 1409192 FRAME, CONVEYOR, LOWER

3 1 1409233 MOUNT WLDMT, NON DRV SIDE

4 1 1409239 MOUNT WLDMT, NON DR SIDE

5 1 1409319 SIDE MOUNT, DR SIDE UPR

6 1 1409321 SIDE MOUNT, DRV SIDE LWR

7 2 1409364 ADJUSTER TEE NUT BLOCK

8 1 1409370 CHAIN TENSIONER ASM UPR, 1409

9 1 1409372 CHAIN TENSIONER ASM BOTOM, 1409

10 1 1409392 KEY, .25 SQ X 2.81

11 2 1409405 ROLLER, BELT, MIDDLE

12 1 1409466 MOUNT, BEARING, BR TL

13 2 1409467 SCREW,BELT TENSION,5/8-18

14 1 1409469 MOUNT, BEARING, BL TR

15 4 1409471 BRNG MOD,FLANGE,1",2 BLT

16 3 1409521 SPROCKET,#40,24T,1.25"B

17 2 1409570 BLOCK, BELT TENSION

18 1 1409594 RUBBER ROLLER ASSY

19 1 1409598 RUBBER ROLLER ASSEMBLY

20 2 MMUCPA209-28 BEARING,PILLOW BLOCK,1.25

21 2 NNH3/8-16 NUT,HEX,3/8-16

22 2 NNJ5/8-18 NUT-HEX JAM 5/8-18

23 2 SSHC01080 1/4-20 X 1-1/4 HHCS

24 18 SSHC25080 3/8-16 X 1-1/4 HHCS

25 8 SSHC25096 3/8-16 X 1 1/2 HHCS

26 2 SSHC25160F 3/8-16x2-1/2,FULL THD,HEX

27 8 SSHC45080 1/2-13X1-1/4 HEX CAP

28 2 SSSC01112 1/4-20 X 1-3/4 SOC CAP

29 8 SSSC25080 3/8-16X1-3/8 SOC CAP

30 4 SSSC45064 SCREW,SOC CAP,1/2-13 X 1"

31 2 UUCFC206-20 BEARING,FLANGE,1.25B,4 BOLT

32 26 WWL1/2 1/2 LOCK WASHER







1409336 ELECTRICAL PANEL1409 ACC Drawing Number 1409336 Rev.3

NO QTY PART # DESCRIPTION1 1 1409337 PANEL, ELECTRICAL

2 1 AAE45A12D VALVE,AIR,SOL,4-WAY

3 2 AAFP18 MUFFLER,1/8 NPT, BRONZ

4 3 AAQMC-4-8 QUICK MALE CONNECT

5 2 EE788311 RELAY,12V,DPDT,WAGO

6 1 EECEBEKI9M FLIP-FLOP RELAY MODULE

7 1 EECGC85A24 CONTACTOR,65A,24VAC

8 1 EEDR1512 POWER SUP. SWITCHER,12V

9 12" EETS35X7.5A DIN RAIL-AMERICAN

10 2 ff67f4079 SPACER,THREADED,1/2

11 1 FF280-308 TERMBLK ENDPLATE,WAGO,280

12 11 FF280-402 JUMPER,WAGO,TOP,SNGL

13 19 FF280-901 TERMBLK,WAGO,TOP,SNGL,GRY

14 1 FFL741C CIRCUIT BREAKER,THERM-MAG

15 1 FFQL213DMKM02 CIRCUIT BREAKER,2A,2P

16 1 FFQL213DMKM20 CIRCUIT BREAKER,20A, 2P

17 1 FFR4.7K RESISTOR, 4.7K, 1/4W.5%

18 1 FFTX28/5A TRANSFORMER,28V,4.6AMP

19 1 MMSM220S DRIVE, VARIABLE FREQ.

20 2 SSHC98024 10-32 X 3/8 HEX CAP

21 4 SSPP80016 #6-32X1/4 PAN PHILLIPS

22 4 SSPP98024 10-32 X 3/8 PAN HD PHILIP

23 4 SSSC90024 #8-32 X 3/8 SOC CAP SC

24 2 SSSC90064 #8-32 X 1 SOC CAP SC

25 4 SSSC98032 10-32X1/2, SOC CAP

26 2 WWF10 WASHER, FLAT, #10, COM






1409574 REWIND GUARD DOOR AAC Drawing Number 1409574 Rev 2

NO QTY PART # DESCRIPTION NO QTY PART # DESCRIPTION

1 3 1409130 12" HINGE 10 18 NNK10-32 KEP NUT, 10-32

2 1 1409362 DOOR STIFFENER 11 4 SSBC98032 10-32 X 1/2 BUTTON CAP SC

3 1 1409411 UPPER GUARD, REWIND,LEFT 12 6 SSBC98040 10-32 X 5/8 BUTTON CAP SC

4 1 1409412 UPPER GUARD, REWIND,RT 13 10 SSFC90024 8-32 X 3/8 FL ALN CAP

5 1 1409510 COVER BRACE, RIGHT 14 2 SSFC90032 8-32 X 1/2 FLAT ALLEN CA

6 1 1409511 COVER BRACE, LEFT 15 8 SSHC98080 10-32 X 1-1/4 HEX CAP

7 2 1409589 CORNER BRACE 16 4 SSSC90080 #8-32 X 1-1/4 SOC CAP SC

8 2 MM1568A45 HANDLE,DOOR,PULL 17 14 WWFS10 WASHER, FLAT, #10, SAE

9 12 NNK8-32 NUT,KEP,8-32 18 4 WWL8 WASHER,LOCK,#8



1409580 GATE SAFETY CONTROL AAC Drawing Number 1409580 Rev 1


1 1 1409585 LIMIT SW ASSY

2 1 1409587 GATE CONTROL SWITCH ASSY

3 1 1409-WD4 WIRING, DBL SOL, & REMOTE

4 1 1409-WD5 WIRING, REMOTE DOOR SW



1409586 GAS SPRING ASSEMBLY AAC Drawing Number 1409586 Rev 1


1 1 1409584 GAS SPRING BRACKET

2 1 MM4138T574 GAS SPRING W/END FITTING

3 4 NNK10-32 KEP NUT, 10-32

4 2 NNK5/16-18 NUT,KEP,5/16-18

5 4 SSBC98040 10-32 X 5/8 BUTTON CAP SC

6 8 WWFS10 WASHER, FLAT, #10, SAE

7 2 WWFS5/16 WASHER,FLAT,SAE,5/16



1409-PD PNEUMATIC DIAGRAM ACC Drawing Number 125998A Rev.2



1409-WD WIRING DIAGRAM ACC Drawing Number 125969B Rev.1



Atlanta Attachment Company (AAC) Statement of

Warranty

Manufactured Products

Atlanta Attachment Company warrants manufactured products to be free from defects in material and

workmanship for a period of eight hundred (800) hours of operation or one hundred (100) days

whichever comes first. Atlanta Attachment Company warrants all electrical components of the Serial Bus

System to be free from defects in material or workmanship for a period of thirty six (36) months.

Terms and Conditions:

AAC Limited Warranty becomes effective on the date of shipment.

AAC Warranty claims may be made by telephone, letter, fax or e-mail. All verbal claims must be con-firmed in writing.

AAC reserves the right to require the return of all claimed defective parts with a completed warranty claim form.

AAC will, at its option, repair or replace the defective machine and parts upon return to AAC.

AAC reserves the right to make the final decision on all warranty coverage questions.

AAC warranty periods as stated are for eight hundred (800) hours or one hundred (100) days whichever comes first.

AAC guarantees satisfactory operation of the machines on the basis of generally accepted industry standards, contingent upon proper application, installation and maintenance.

AAC Limited Warranty may not be changed or modified and is not subject to any other warranty expressed or implied by any other agent, dealer, or distributor unless approved in writing by AAC in advance of any claim being filed.

What Is Covered

Electrical components that are not included within the Serial Bus System that fail due to defects in material or workmanship, which are manufactured by AAC are covered for a period of eight hundred (800) hours.

Mechanical parts or components that fail due to defects in material or workmanship, which are manufactured by AAC.

Purchased items (sewing heads, motors, etc.) will be covered by the manufacturers (OEM) warranty.

AAC will assist in the procurement and handling of the manufacturers (OEM) claim.



What Is Not Covered

Parts that fail due to improper usage, lack of proper maintenance, lubrication and/or modification.

Damages caused by; improper freight handling, accidents, fire and issues resulting from unauthorized service and/or personnel, improper electrical, plumbing connections.

Normal wear of machine and parts such as Conveyor belts, "O" rings, gauge parts, cutters, needles, etc.

Machine adjustments related to sewing applications and/or general machine operation.

Charges for field service.

Loss of time, potential revenue, and/or profits.

Personal injury and/or property damage resulting from the operation of this equipment.

Declaración de Garantía

Productos Manufacturados

Atlanta Attachment Company garantiza que los productos de fabricación son libres de defectos de mate-

rial y de mano de obra durante un periodo de ochocientos (800) horas de operación o cien (100) días

cual llegue primero. Atlanta Attachment Company garantiza que todos los componentes del Serial bus

son libres de defectos de material y de mano de obra durante un periodo de treinta y seis (36) meses.

Términos y Condiciones:

La Garantía Limitada de AAC entra en efecto el día de transporte.

Reclamos de la Garantía de AAC pueden ser realizados por teléfono, carta, fax o correo electrónico. Todo reclamo verbal tiene que ser confirmado vía escrito.

AAC reserva el derecho para exigir el retorno de cada pieza defectuosa con un formulario de reclamo de garantía.

AAC va, según su criterio, reparar o reemplazar las máquinas o piezas defectuosas devueltas para AAC.

AAC reserva el derecho para tomar la decisión final sobre toda cuestión de garantía.

Las garantías de AAC tiene una validez de ochocientas (800) horas o cien (100) días cual llega primero.

AAC garantiza la operación satisfactoria de sus máquinas en base de las normas aceptadas de la industria siempre y cuando se instale use y mantenga de forma apropiada.



La garantía de AAC no puede ser cambiado o modificado y no está sujeto a cualquier otra garantía implicado por otro agente o distribuidor menos al menos que sea autorizado por AAC antes de cualquier reclamo.

Lo Que Está Garantizado

Componentes eléctricos que no están incluidos dentro del sistema Serial Bus que fallen por defectos de materiales o de fabricación que han sido manufacturados por AAC son garantizados por un peri-odo de ochocientas (800) horas.

Componentes mecánicos que fallen por defectos de materiales o de fabricación que han sido manu-facturados por AAC son garantizados por un periodo de ochocientas (800) horas.

Componentes comprados (Motores, Cabezales,) son protegidos debajo de la garantía del fabricante.

AAC asistirá con el manejo de todo reclamo de garantía bajo la garantía del fabricante.

Lo Que No Está Garantizado

Falla de repuestos al raíz de uso incorrecto, falta de mantenimiento, lubricación o modificación.

Daños ocurridos a raíz de mal transporte, accidentes, incendios o cualquier daño como resultado de servicio por personas no autorizados o instalaciones incorrectas de conexiones eléctricas o neumáticas.

Desgaste normal de piezas como correas, anillos de goma, cuchillas, agujas, etc.

Ajustes de la máquina en relación a las aplicaciones de costura y/o la operación en general de la máquina.

Gastos de Reparaciones fuera de las instalaciones de AAC

Pérdida de tiempo, ingresos potenciales, y/o ganancias.

Daños personales y/o daños a la propiedad como resultado de la operación de este equipo.



Atlanta Attachment Company

362 Industrial Park Drive

Lawrenceville, GA 30046

770-963-7369

www.atlatt.com Printed in the USA

http://www.atlatt.com/

Date post:	12-Oct-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Rev 1.7 Updated May.16/2016 Technical Manual & Parts Lists€¦ · 362 Industrial Park Drive...

Documents