Order No. PHAT080802C3(REVISION : AUG. 2011)
Service ManualElectric Rice Cooker
SR-TEM10 / SR-TEM18SR-TEM10F / SR-TEM18F
© Panasonic Home Appliances (Thailand) Co., Ltd. 2008.All rights reserved. Unauthorized copying and distributionis a violation of law. (Company No. 6100K)
There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential thatthese critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Donot modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
The service information is designed for experienced repair technicians only and is not designed for use by the generalpublic. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attemptingto service a product. Products powered by electricity should be serviced or repaired only by experienced professionaltechnicians. Any attempt to service or repair the product or products dealt within this service information by anyoneelse could result in serious injury or death.
WARNING
DestinationThailand, Singapore (DBD)
Singapore (RBD), IndonesiaHong Kong, Taiwan
Product ColourMohogany (MH), Deep Gray (DG)
Metalic Maple (MM), Metalic Gold (MG)Crystal Silver (CS), Mohogany Flower (MF)
White Butterfly (WB), Graphic Blue (GB)
- 2 -
CONTENT
Page
34
55
6 - 7
8899
1010
1112
13 - 1718
1. Specification 2. Parts Identification 3. Schematic Diagram 3.1 Circuit Diagram 3.2 Wiring Diagram 4. Troubleshooting Guide 5. Testing Procedure 5.1 Bubbling Test 5.2 Evaporation Test 5.3 Heat reserving Test 5.4 Boiling control lever adjustment 5.5 Hing cover removal (Hinge Cover) 5.6 Inner enclosure and upper frame removal 6. Parts Exploded View and Replacement Parts List 6.1 Parts Exploded View : Body 6.2 Parts Exploded View : Packing 6.3 Replacement Parts List : SR-TEM10 / SR-TEM18, SR-TEM10F / SR-TEM18F 7. Detail Change Notice
SR-TEM10 / TEM18 / TEM10F / TEM18F
- 3 -
1. SPECIFICATION
MODEL
Power Supply
Power Consumption
Power Cord
Cooking
Keeping Warm
220V 50Hz
230V 50Hz
240V 50Hz
110V 60Hz
Taiwan
Thailand
Singapore (DBD)Hong Kong
Singapore (RBD)Indonesia
All countries
Cooking Capacity (White Rice)
SR-TEM10 SR-TEM18 SR-TEM10F SR-TEM18F
IndonesiaSingapore (RBD)
Singapore (DBD)
IndonesiaSingapore (RBD)
Singapore (DBD)
Hong Kong
Taiwan
Hong Kong
Thailand
-
Thailand
-
- -
--
S3PS3P
SH3P
Kind
Length
A3P
SH3P
-
--
- -
-
- -
- -
C3P C3P
1M 1M 1M 1M
600W 800W 600W 800W
32W 33W 32W 33W
2.5 Kgs. 3.1 Kgs. 2.5 Kgs. 3.1 Kgs.
1 ~ 5 cups 3 ~ 10 cups 1 ~ 5 cups 3 ~ 10 cups
248 x 247 x 255 276 x 274 x 278 248 x 247 x 255 276 x 274 x 278Product Dimension [ W x D x H ] (mm)
Center Thermostat Working Temperature
Thermal Fuse Specification
Weight (Approx.)
Accessories
125°C ± 6°C
142°C
Steaming basket, Scoop, Measuring cup, Power Cord
SR-TEM10 / TEM18 / TEM10F / TEM18F
- 4 -
2. PARTS IDENTIFICATION
SR-TEM10 / TEM18 / TEM10F / TEM18F
Warm lamp
Cook lamp
Accessories
Steaming basket Rice scoop AC cord Measuring cup (Approx 180 ml)
- 5 -
3. SCHEMATIC DIAGRAM
3.1 Circuit Diagram
3.2 Wiring Diagram
SR-TEM10 / TEM18 / TEM10F / TEM18F
Black
ThermalFuse
Power
Black
N
Red
NC
Micro Switch
NOC
(White : 18/Yellow : 10)
Earth Lead Wire Green
L
E Green
Circuit Diagram
Rice CookLamp
Keep WarmLamp
SideHeater
CastHeaterThermal
Fuse
Lamp lead wire B (White),C (Red) and side heater lead wire B (Blue) shall be bundled 1.5 times with lamp lead wire A (Black).
The Clearance distance between terminal & sems screwto other dead metal part (Protecting Frame,Cast Heater Pipe) should be minimum 3.6mm. (Any direction) After inspection, screw head must be mark with marker.
Thermal Fuse Lead Wire A (Black)
Tapping Screw For Body Earth Lead Wire
Earth Connection
Lamp Lead Wire A (Black)
Lamp Lead Wire B (White)
Lamp Lead Wire C (Red)
Side Heater Lead Wire B (Blue)
Rice cooking lever
Terminal shall not be higher than head of sems screw.
Lamp Lead Wire C (Red)To inlet
Lamp Lead Wire B (White)
Lamp Lead Wire B(White : 18 / Yellow : 10)
Body Earth Lead Wire Yellow Spiral Green
Thermal Fuse Lead Wire B(Black)
Side Heater Lead Wire A (Red)
Body Earth Lead Wire Yellow Spiral Green
Sems Screw for Internal Wiring
Thermostat Rod bending shall be straight
- 6 -
4. TROUBLESHOOTING GUIDE
SR-TEM10 / TEM18 / TEM10F / TEM18F
Condition
Rice boiling section
• Rice is not boiling.(The indicating lamp does not come on)
• Rice is not boiling.(The indicating lamp is lit)
Troubleshooting Remedy
Is the power cord conductive? • Replace the cord.
• Replace the micro switch.
• Adjust the control lever.
• Replace the cast heater.
• Replace the micro switch.
• Explain the proper operation.
• Isolate the cause which melt the thermal fuse, correct the cause and replace the fuse.
• The thermal fuse is blown off.
Yes
No
Is the thermal fuse conductive?
Yes
No
Is the micro switch (across C to NC)conductive when the rice boiling processis turned on?
Is the micro switch (across C to NC)conductive when the rice boiling processis turned off?
Yes
Is the rice boiling control lever properlyadjusted?
The operation is wrong.(Forcibly flow the electric current).
(Check with the evaporation test).
No
No
• Adjust the control lever.
No
Yes
Is the rice boiling control lever properlyadjusted?
No
Yes
Yes
• Replace the center thermostat.Does the center thermostat operateproperly?
Yes
No
Is the cast heater conductive? No
When receiving a rice boiler to be repaired, be sure to check that the main body is completely provide with the inner panand the inner lid, ask the condition (phenmenon) of the trouble in detail. Before troubleshooting single parts, be sure todisconnect the power supply plug from the receptacle.
- 7 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
Condition Troubleshooting Remedy
• Replace the center thermostat.
• Replace the inner pan or the cast heater.
• Replace the cast heater.
• Explain the proper operation.
• Earlier cut off.
• Excessive burning
• Poor boiling up.
• Too hard• Too soft• Cored rice Insufficient boiling
• Immediately after the switch is turned off, open the cap.
• Rice is excessive or insufficient.• Water is excessive or insufficient.• The switch is turned off once during boiling.
• Rice has not been scooped and mixed well.
Is the pan bottom properly contacted with the cast heater?
Is the cast heater conductive?
Improper operation
Yes
No
No
• Explain the proper operation.
• Mixed rice is boiled.
• Rice is not washed sufficiently. (Bran remains still).
• The pan bottom is conditioned to generate burning easily.
• Germ rice or wheat-mixed rice is boiled.
• The voltage is lower than specified.• Water is excessive.
Improper operation
Yes
No
(Check with the bubbling test).
Does the center thermostat operateproperly?
Yes
Yes
Yes
No
(Check with the operation test).
• Adjust the control lever.Is the rice boiling control lever properlyadjusted?
No
• Replace the center thermostat.Does the center thermostat operateproperly?
Yes
Yes
No
(Check with the evaporation test).
• Adjust the control lever.Is the rice boiling control lever properlyadjusted?
No
(More than light brown)
- 8 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
5. TESTING PROCEDURE
5.1 Bubbling testInput the pan in the main body, lightly rotate the pan clockwise and counter clockwise to settle the pan on theheating plate properly.
1. Fill water until center area of the pan bottom is dipped and close the lid. Then turn on the boiling switch.
5.2 Evaporation test1. Check that bubbling is proper, open the lid and place a weight.
2. Fully cover 2 to 3 sheet of tissue paper (gauze is also applicable) on the pan bottom and continuously flow electric current.
Note : To prevent plastic parts from deformation caused by steam, be sure to open the lid fully.
Note : To prevent tissue paper from floating because of bubbling, previously hole the paper.
3. Water on the pan bottom is completely evaporated to be empty. This timing is an follows :
Within 1 minute before the boiling switch is turned off.Within 1 minute after the boiling switch is turned off.
Place a weight so that its gravity center may be aligned at the center
2. When it beings boiling to produce steam. Remove the lid immediately check the bubbling condition on the pan bottom.
3. As show in the figture.
If it is improper, it may result from the insufficient contact between the pan bottom and heating plate. Check the pan bottom and the heating plate for foreign material remainder. Clean off the foreign materials or replace the parts.
Bubbles generate through out the circumference of the pan bottom...............................................Proper
Bubbles does not generate on more than one quater part of the pan bottom circumference..........Improper
Bubbling
- 9 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
5.3 Heat reserving test
The above conditions are proper.
1. Put approx. 1 liter of water and the thermometer [ repairing tool (mercury thermometer ASN-150H) ] in the pan, close the lid and turn on the boiling switch.2. When the beings boiling to generate steam turn off the boiling switch.
Within 69°C - 77°C .....................................Proper
If outside 69°C - 77°C, check TRS mounting for irregularity, if it is proper, replace warming heater.
If it is improper, check the contact between the pan bottom, the heating plate and the center thermostat. Repair or replace if necessary.
3. Add water or keep the lid opened until the reading of the thermometer falls to approx. 70°C.
4. When it becomes approx. 70°C, close the lid. After the warming heater is activated for 1 hour or more, check the heat reserving temperature.
Top view of pan
Holes on thetissue paper
Pan flange
Tissue paper
Mercury thermometer
Urethane foam blocks
Mercury thermometer
Inner Pan
5.4 Boiling control lever adjustmentSuch a mechanical operation as center thermostat goes up and down is used to turn on and off the micro-switch. Check and adjust this relationship as shown below.
The auxiliary lever presses the push-button.(The heat reserving lamp come on).
To gain the above relationship, adjust the auxiliary lever by bending it with long nose pliers.
The auxiliary lever does not press the push-button. (The boiling indication lamp comes on).
Checking
Adjusting
When the boiling switch is turned on When the boiling switch is turned off
- 10 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
5.5 Hinge cover removal (Hinge cover)1. Remove the dew collector.
2. Remove the hinge cover mounting screws.
3. As show in the figure, insert a narrow flat head screwdriver from just below and pry off the hinge cover.
Hinge cover
Hinge covermounting screwremove
5.6 Inner enclosure and upper frame removal1. As show in the figure, pry up three fastening hooks. Fixing the upper frame, turn the inner enclosure in the arrow direction.2. The upper frame will be seperated from the inner enclosure and the upper frame.
- 11 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
6. PARTS EXPLODED VIEW AND REPLACEMENT PARTS LIST
6.1 Parts Exploded View : Body
- 12 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
6.2 Parts Exploded View : Packing
- 13 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
6.3 Replacement Parts List : SR-TEM10 / SR-TEM18, SR-TEM10F / SR-TEM18F
Important safety notice :
Parts List
REF.NO.
PART NAME PART NO. SAFETY
S
Components identified by mark have special characteristics important for safety.When replacing any of these components, use only manufacturer’s specified part.
REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
1
1
1
1
1
1
1
1
1 1 1 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1 1
1
1
1 1
1
1
1
1
1
1
1
1
1
1
1
1 1 1
1 1 1 1 11
1
1
1
1
1
1 1 1
1 1 1 1 11
1 1
1
1
1
1
1
1 1 1
1 1 1 1 11
1 1 1 1 11
1 1 1 1
1 1 1 11
1 1 1 1 11
OUTER LID ASSY ARB00T960MQU
ARB00T960EGU
ARB00T959EGU
ARB00T960W9U
ARB00S960W9U
ARB00T959W9U
ARB00S959W9U
ARB00L959W9U
ARB00V959W9U
ARB00U959W9U
ARB00T959MQU
1
HOOK LEVER ARE05H617-MQ
ARE05H617-EG
ARE05H617-W9
ARE05H616-MQ
ARE05H616-EQ
ARE05H616-W9
2
HOOK LEVER SPRING ARE06H6163
HOOK LEVER BASE ARC31H617
ARC31H616
4
HAND COVER ARB15T921-MQ
ARB15T921-EG
ARB15T921-W9
ARB15T920-W9
ARB15T920-MQ
ARB15T920-EG
5
HANDLE ARB10T9211MQ
ARB10T9211EG
ARB10T9211W9
ARB10T920-MQ
ARB10T920-EG
ARB10T920-W9
6
CAUTION LABEL ARB32T9591
SARB32S959
SARB32V959
SARB32L959
SARB32U959
7
OUTER LID COMP. ARB01T960MQU
ARB01T960EGU
ARB01T960W9U
ARB01T959MQU
ARB01T959EGU
ARB01T959W9U
8
STEAM VENT PACKING9
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB
COLOUR : CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB
COLOUR : CS, MG, MM
COLOUR : CS, MG, MM
COLOUR : CS, MG
COLOUR : MG
COLOUR : MH
COLOUR : DG
COLOUR : W
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : MH
COLOUR : DG
COLOUR : W
1 1 1 1 11
OUTER LID ARB01T960-MQ
ARB01T960-EG
ARB01T959-W9
ARB31T959
ARB01T960-W9
ARB01T959-MQ
ARB01T959-EG
8.1 COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
- 14 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
Parts List
REF.NO.
PART NAME PART NO. SAFETY
S
S
S
REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
1
1
1
1
1
1
1 1 1 1
1 11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1
1 1
1 1 1
1
1 1 1 1
11 1 1 1
11 1 1
1
1
1
1
1 1 1
1
1
1 1 1
1
2
1
1
1
1 1 1
1 1 1 1
1 11
1
1
1
1
1
1
1 1 1
1 1 1
1
1
1
1
1
1 1
11111
1111
1
1
1
1
1
1
1
11
1
1 1 1 11
1 1 1 11
4
1
1
1
1
1 1
1
1
1
1 1 1 11
2 2 2 22
1
1
1
1 1
4 4 4
1
44
PAN PACKING ASR171T858-K
ASR171T929-K
ARB90U959-0U
ARB90T267-0U
ARB90T265-0U
ARC80-255
ARC80-253
ASR129T929-K
ARE50T9601
ARE50T9591
ARB90L959-0U
10
PACKING HOLDINGPLATE ASSY
11
INNER LID12
INNER LID HOLDER13
PAN(BLACK FLUORO)
14
THERMOSTAT ASSY
ARE50S9591
ARS00H920B0U
ARS61H616
ARL20T960-0U
SARL20S960-0U
SARL20T95910U
SARL20S95910U
15
OUTER SPRING16
CAST HEATER ASSY17
BUSH ARS22H761-H0
ARE00T960-MQ
ARE00T960-EG
ARE00T959-EG
ARE00T960-W9
ARE00T959-MQ
18
UPPER FRAME19
HINGE SHAFT
ARE00L616-W9
ARB74H616
ARE20T921
ARE20T9201
ARN40T92110U
ARN48H616
20
PROTECTING FRAME21
THERMAL FUSE ASSY22
THERMAL FUSE HOLDER
23
SARL10H61710U
SARL10S617-0U
S
S
ARL10H61610U
ARL10S61610U
SARL10L61610U
SIDE HEATER ASSY24
BODY ASSY25
SWITCH ASSY26
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB
COLOUR : MF
COLOUR : WB
COLOUR : MH, DG
COLOUR : GB
COLOUR : MH, DG
COLOUR : MG
COLOUR : CS
COLOUR : MM
COLOUR : MF
COLOUR : MM
COLOUR : MG
COLOUR : CS
COLOUR : MF
COLOUR : DG
COLOUR : GB, MF, WB
COLOUR : WB
SARL20L959-0U
SARL20U959-0U
SARL10U920-0U
ARE10T927MFU
ARE10T927WBU
ARE10T927GBU
ARE10T927CSU
ARE10T960MGU
ARE10T960MMU
ARE10T920MFU
ARE10T920WBU
ARE10T920GBU
ARE10T926CSU
ARE10S959MMU
ARE10S959MGU
ARE10S959CSU
ARN01T921W9U
ARN01T921MQU
ARN01T921EGU
ARE10T921CSU
- 15 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
Parts List
REF.NO.
PART NAME PART NO. SAFETY REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
1
1
1
1
1
1
1 11 1
1
1
1
1
1
1
1 1
1
1
1 1
1
1 1 1 1
11 1 1
1
1
1
1
1
1
1
1
1 1 1
1 1 1 1
1 11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1
1
1
1 1 1
1
1
1
1
1 1 1
1 1 1 11
1
1 1 1
1
1
1 1 1
1 1 1 1 1
1 1 1 1
ARN70T921-MQ
ARN01T960W9U
ARN01T920MQU
ARN01T920EGU
ARN01T920W9U
ARN01T959W9U
ARN01U959W9U
ARN70T921-EG
ARN70T921-W9
ARN70T920-MQ
ARN70T920-EG
ARN70T920-W9
SWITCH BUTTON27
DECORATIVE PANEL ARN21T920-W9
ARN21T920-UH
ARN21T959-W9
ARN21U959-W9
ARN10T920-MQ
ARN10T920-EG
ARN10T920-W9
S
28
SWITCH PANEL29
LAMP BOARD ASSY
AQN60T92110U
AQN60H921-0U
AQN60T92010U
AQN60H920-0U
30
FRAME COMPLETE31
BOTTOM FRAME ARH30T9212MQ
ARH30T9212EG
ARH30T9212W9
ARH30T9202MQ
ARH30T9202EG
ARH30T9202W9
32
SARG10T92010U
SARQ00T959-0U
ARQ00M96110U
ARQ00T920-0U
ARQ00T68310U
S
S
S
INLET33
POWER CORD ASSY34
NAME PLATE35
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB
COLOUR : CS, MG, MM
COLOUR : CS, MG, MM
COLOUR : MG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : GB, MF, WB, MH
COLOUR : MH
COLOUR : DG
COLOUR : DG
COLOUR : CS, MG, MM
COLOUR : MG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : DG
COLOUR : MH
COLOUR : DG
COLOUR : GB, MF, WB, CS, MG, MM
TYPE : C3
TYPE : S3
TYPE : SH3
TYPE : A3
COLOUR : CS
COLOUR : MG
COLOUR : GB, MF, WB, MH, DG
COLOUR : CS
COLOUR : MG
COLOUR : MM
COLOUR : MG
COLOUR : CS
COLOUR : MG
COLOUR : GB, MF, WB, MH, DG
COLOUR : MG
COLOUR : CS
COLOUR : CS
COLOUR : MG
COLOUR : MG
COLOUR : MG
COLOUR : MM
COLOUR : CS
COLOUR : CS
S
S
ARN85T921-0U
ARN85T92010U
ARN85U920-0U
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
ARY30T960
ARY30S9601MG
ARY30S9601CS
ARY30V960-CS
ARY30V960-MG
ARY30H960-CS
ARY30H960-MG
ARY30T959
ARY30S9591MG
ARY30S9591CS
ARY30L959-MM
ARY30L959-MG
ARY30L959-CS
ARY30V959-CS
ARY30V959-MG
ARY30H959-CS
ARY30H959-MG
ARY30H959-MM
ARY30U959-MG
- 16 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
Parts List
REF.NO.
PART NAME PART NO. SAFETY REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
1
1
1
1
1
1
1 1
1
1
1
1
1
1
1
1
1
1
1
1 1 11 1
1 1
1
1 1 1 1
11 1 1 1
HINGE COVER ARE40T959-MQ
ARE40T959-EG
ASR796-454AK
ARE40H6161W9
ARK10H616-C0
ASR79WT281AK
ARK53H617-W9
ARK53H616-W9
ASR792-454BK
36
DEW COLLECTOR37
MEASURING CUP38
SCOOP39
STEAM BASKET40
COLOUR : GB, MF, WB, CS, MG, MM
COLOUR : MH
COLOUR : DG
Screws
REF.NO.
PART NAME PART NO. SAFETY REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
2
1
1
1
1
1 1
1
1
1
1
1
1
1
1
2
1
1
2 22 2
2 22 22 2
2 22 22 2
1 1
1
1 1 1 11
1
1
1 1 1
1
1 1
1 1 1 1
6 66 6 6 6
TAPPING SCREW
TAPPING SCREW
TAPPING SCREW
TAPPING SCREW
TAPPING SCREW
SPRING WASHER
SEMS SCREW
SEMS SCREW
XTB4+10GFJ
XYN4+C10FNS
XWA3BPW
XTN4+6FFJ
XTN4+6FFJ
XYN4+C7FNS
ASR118-972-W
XTN4+16AVW
XTL4+10RTW
XYN4+8FFJ
A
B
C
D
E
F
G
H
TAPPING SCREWI
FOR THERMAL FUSE ASSY
FOR FRAME ASSY
FOR INTERNAL WIRING
FOR BODY EARTH LEAD WIRE
FOR BODY EARTH LEAD WIRE
FOR BOTTOM FRAME
FOR HINGE COVER
FOR PACKING HOLDING PLATE
FOR HANDLE
FOR CAST HEATER ASSY
- 17 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
Packing List
REF.NO.
PART NAME PART NO. SAFETY REMARK
COUNTRIES / Q’TY
TEM18TEM10
MODEL
TH SIN-DBD
INDO SIN-RBD
HK TAI
1
1
1
1
1
1
1
1
1
1
1
1
1 1
1
1 1
1 1
1 11 1
1
1 1 1 1
1
1
1 1 1
1 1
111 1 1
111 1 11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ARZ80T959-0U
ARZ19T959
ARZ19S9591
ARZ19V959
ARZ19L9591
ARZ19U959
ASR762T929-K
ASR758T344B
ASR761H915-K
ARZ11T921-0U
POLYETHYLENESHEET
OPERATINGINSTRUCTION
3
ARZ80T960-0UUPPER PAD ASSY2
1
INNER PACKING CASE
ARZ11T920-0U
ARZ01T960-MH
ARZ01T960-DG
ARZ01T960-MF
ARZ01T960-WB
ARZ01T960-GB
ARZ01S960-MG
S7
RUST PROOF PAPER4
CORD PROTECTOR5
LOWER PAD ASSY6
ARZ01H960-CS
ARZ01H960-MG
ARZ01H960-MM
ARZ01T959-MH
ARZ01T959-DG
ARZ01T959-MF
ARZ01T959-WB
ARZ01T959-GB
ARZ01S959-MG
ARZ01S959-CS
S
ARZ01L959-MM
S
ARZ01L959-MG
ARZ01L959-CS
ARZ01V959-CS
ARZ01V959-MG
S
S
S
COLOUR : MF
COLOUR : MH
COLOUR : MH
COLOUR : DG
COLOUR : MF
COLOUR : WB
COLOUR : GB
COLOUR : MG
COLOUR : CS
COLOUR : MG
COLOUR : MG
COLOUR : MM
COLOUR : CS
COLOUR : CS
COLOUR : DG
COLOUR : WB
COLOUR : GB
COLOUR : MG
COLOUR : CS
COLOUR : CS
COLOUR : CS
COLOUR : MM
COLOUR : MG
COLOUR : MG
COLOUR : MG
COLOUR : CS
COLOUR : MG
COLOUR : MM
S
S
S
S
S
S
S
ARZ01S960-CS
ARZ01V960-CS
ARZ01V960-MG S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
ARZ01H959-CS
ARZ01H959-MG
ARZ01H959-MM
ARZ01U959-MG
- 18 -
SR-TEM10 / TEM18 / TEM10F / TEM18F
DETAIL CHANGE NOTICE
REVISION ITEM NO. PAGE DETAIL REMARK
JAN. 2010 1 13 CHANGE PART NO. OF PAN (BLACK FLUORO)
CHANGE COATING FROM 1 TO 2 LAYER
AUG. 2011 1 2 ADD NEW PAGE FOR CONTENT IT’S PAGE NO. 2
2 2 - 18 NEW RUNNING PAGE NO. & SUBJECT NEW PAGE NO. 2 - 18
3 15 CHANGE PART NO. OF POWER CORDASSY
CHANGE 10A 250V TO 13A 250V