24
DORMA KTC-2 KTV-2 Revolving doors 2-wing design
DORMA KTC-2KTV-2
Revolving doors2-wing design
The entrance area is theshowcase of a building. Noother part of the buildinghas such a lasting firstimpression on visitors andthereby gives them an ideaof their further stay. Highrequirements therefore haveto be placed on the visualquality of a door system, ondesign and functionality.The DORMA KTC-2 two-wingrevolving door offers plentyof scope for architecturalcreativity. Thanks to the
variability of its design and a broad selection of surfacefinishes, it will turn theentrance of any building into a prestigious entrée.Easy to operate and ideallysuited for the requirementsof wheelchair users (pleaserefer to page 10 for furtherdetails), the DORMA KTC-2also raises accessibility andconvenience to a new level.The wide range of functionsensures high traffic capacityeven during peak traffic
periods, plus unbeatablesafety. And there are majoradditional benefits to be had from the suitability of these doors as display and advertising spaces.It is important for the econo-mic operation of a buildingto guarantee effective protec-tion of its interior against the cold, heat, draughts,noise and dust. The two-wingDORMA KTC-2 revolvingdoor comprehensively meetsall these requirements.
Available in three standardsizes, with two breakout doorwings respectively – eitheras continuous arrangementwithout showcases or with external showcases –DORMA KTC-2 revolvingdoors are suitable for avariety of applications.System options include anintegrated night shield andthe choice of either drumwalls with glazing or metalpanelling.
A sophisticated entrance system offeringboth safety and comfort.
2 KTC-2/KTV-2 GB
Revolving door DORMA KTC-2
3KTC-2/KTV-2 GB
The two-wing revolving doorKTV 2 is the small version ofthe KTC 2. It is availablewith a diameter of 3,000 mmand 3,400 mm and thuscombines all benefits of theKTC 2/0 (version withoutshowcase) with smallerinstallation dimensions. This makes the KTV 2 thesuitable application wherespace is tight and never-theless a maximum sectionsize and an unobstructed
passage through the center ofthe door system is required.It is appropriate for hospitalsor residential homes for theelderly, but also for officebuildings or hotels. The KTV 2 also provides the elegance of the KTC 2and will thus enhance thefaçade of your building. No matter if surface finishesin RAL colours, anodisedsurface finishes or stainlesssteel coatings of all qualities
– the KTV 2 combines abeautiful entrance area withan intelligent automatic doorsystem.
Much space on little room
Revolving door DORMA KTV-2
KTC-2/2
2 Spacious entrance2 Easy transport of bulky
goods2 Suitable for the needs of
the disabled2 Large sections2 Integrated night shield2 Optional showcases
provide advertising space
2 Highest safety standard2 Suitable for application
as escape route door2 Complete application
with industrial precisionand trusted quality
Benefits
Internal diameter in mm (D) 3600, 4200, 4800
External diameter in mm (B) 3828, 4428, 5028
Clear passage width in mm (LW) 1627, 1927, 2227
Escape route width in mm = LW(clear passage width)
Clear passage height in mm (LH) 2100-2200*
Canopy height in mm 410-700
System height in mm (H) Clear passage height+ canopy height
Glazed drum walls X
Drum walls with metal panelling X
Suitable for installation in emergency exits and escape routes X
Floor ring x
Floor finish X
4 downlights x
Prepared for rainproof ceiling X
German type approval in accordance with DIN 18650 X
Realised according to DIN 18650 X
x yes X option*larger clear passage heights on request
Technical data and features DORMA KTC-2 KTC-2/0Versions
Canopy-integrated drive unit
Operator types
I: The door starts andstops automatically. II: The door rotatespermanently at lowspeed. The speed isincreased as soon as aperson approaches thedoor system.
Speed limitationThis feature reducesthe speed to approx. 1 rpm, for example forelderly people or thedisabled.
Automatic
Summer configurationThis configuration isalso perfectly suitablefor the transport ofbulky items or luggageand deliveries of goods.
Emergency escapeconfiguration
Configurations
The rotor can be lockedelectrically.
Night shield
Revolving door DORMA KTC-2/0DORMA KTC-2/2
Versions, functions, equipment, options
4 KTC-2/KTV-2 GB
The rotor can be lockedelectrically.
Night shield
Revolving door DORMA KTV-2
Internal diameter in mm (D) 3000, 3400
External diameter in mm (B) 3216, 3616
Clear passage width in mm (LW) 1362, 1562
Escape route width in mm = LW(clear passage width)
Clear passage height in mm (LH) 2100 to 2200*
Canopy height in mm min. 354, min. 364
Glazed drum walls X
Drum walls with metal panelling X
For emergency exits and escape routes X
Floor ring x
Floor finish X
4 downlights X
Prepared for rainproof ceiling X
German type approval in accordance with DIN 18650 X
x yes X option
*larger clear passage heights on request
Technical data and features DORMA KTV-2 KTV-2/0Versions
Canopy-integrated drive unit
Operator types
I: The door starts and stopsautomatically. II: The door rotates perma-nently at low speed. Thespeed is increased as soonas a person approaches thedoor system.
Speed limitationThis feature reduces thespeed to approx. 1 rpm, forexample for elderly people orthe disabled.
Automatic
Summer configurationThis configuration is alsoperfectly suitable for thetransport of bulky items orluggage and deliveries ofgoods.
Emergency escape configuration
Configurations
2 Flexible system thatmeets any requirement.
2 Easy installation and fastcommissioning.
2 Guaranteed state of the art technology and compliance with allregulations.
2 The perfect application in visual, technical andeconomical respect.
2 Improves the building’senergy balance.
2 Effective noise control.2 Customised application
with industrial precisionand trusted quality.
Benefits
5KTC-2/KTV-2 GB
LHS
H
H
B1
B2
D
LW
110
110
LHS
H
H
B2
B1
D
LW
110
110
Internal diameter (D) 3600 4200 4800
External diameter (B1) 3692 4292 4892
External diameter (B2) 3828 4428 5028
Clear passage width (LW) 1627 1927 2227
Clear passage height (LH) 2100-2200*
Canopy height (SH) 410-700
System height (H) Clear passage height + canopy height
All dimensions in mm.*larger clear passage heights on request
Dimensions
KTC-2/2 with showcases
2 The KTC-2/2 version isadditionally equipped withtwo external triangularshowcases
2 Max. weight of showcasedécor = 30 kg
KTC-2/0 without showcases
2 The two-wing KTC-2/0revolving door system isavailable in three standardsizes with 2 breakout doorwings including brushseals
2 The integrated nightshield is equipped with8.7 mm laminated safetyglass (with foil)
2 The drum walls areavailable with glazing ormetal panelling
KTC-2/0 without showcases KTC-2/2 with showcases
6 KTC-2/KTV-2 GB
Revolving door DORMA KTC-2/0DORMA KTC-2/2
7KTC-2/KTV-2 GB
Revolving door DORMA KTV-2
SH
LH H
10
0
10
0
10
0
D
LW
B
65
Drum wall withglazing made of safety glass
Drum wall withmetal panelling
Drum wall withintegrated night shield
Internal diameter (D) 3000 3400
External diameter (B) 3216 3616
Canopy height (SH) min. 354 min. 364
Clear passage width (LW) 1362 1565
All dimensions in mm.
Dimension of KTV-2KTV-2
Two-wing version withintegrated night shield andbreakout wings for summerconfiguration. Full-automaticdoors with integrated safetypackage:
You may chose between twotypes of drum walls2 Aluminium frame with
glazing2 Aluminium frame with
metal panelling
KTV-2
Passage without shopping trolley
8 KTC-2/KTV-2 GB
Revolving door DORMA KTC-2Traffic capacity
Theoretical traffic capacity for KTC-2All indicated traffic capacitiesare to be regarded as theore-tical values, calculated forpassage from both directions(one direction = half thevalue).
The actual traffic capacitydepends, among others, on the shape of the show-case and the operationalenvironment.
Therefore the actual valuesmay be lower than theindicated theoretical values.
Speed at the end of the door wing: 0.6 m/sec
Required space per person: 0.7 m2
Area utilisation per section: 80 %
Diameter (m): 3.6 4.2 4.8
People per section: 3.0 5.0 6.0
Rotations per minute (rpm): 3.2 2.7 2.4
People per hour: 1145.9 1637.0 1718.9
Theoretical traffic capacity per hour= Number of door wings x people per section x rotations per minute x 60 min
Passage with shopping trolley
Speed at the end of the door wing: 0.6 m/sec
Required space per person: 2.0 m2
Area utilisation per section: 60 %
Diameter (m): 3.6 4.2 4.8
People per section: 1.0 1.0 1.0
Rotations per minute (rpm): 3.2 2.7 2.4
People per hour: 382.0 327.4 286.5
Theoretical traffic capacity per hour= Number of door wings x (people + shopping trolleys per section) x rotations per minute
x 60 min
Passage with wheelchairs
Speed at the end of the door wing: 0.3 m/sec
Required space per person: 2.0 m2
Area utilisation per section: 60 %
Diameter (m): 3.6 4.2 4.8
People per section: 1.0 1.0 1.0
Rotations per minute (rpm): 1.6 1.4 1.2
People per hour: 191.0 163.7 143.2
Theoretical traffic capacity per hour= Number of door wings x (people + wheelchair per section) x rotations per minute
x 60 min
9KTC-2/KTV-2 GB
Passage without shopping trolley
Theoretical traffic capacity for KTV-2All indicated traffic capacitiesare to be regarded as theore-tical values, calculated forpassage from both directions(one direction = half thevalue).
The actual traffic capacitydepends, among others, on the shape of the show-case and the operationalenvironment.
Therefore the actual valuesmay be lower than theindicated theoretical values.
Speed at the end of the door wing: 0.6 m/sec
Required space per person: 0.7 m2
Area utilisation per section: 80 %
Diameter (m): 3.0 3.4
People per section: 2.0 3.0
Rotations per minute (rpm): 3.8 3.4
People per hour: 916.7 1213.3
Theoretical traffic capacity per hour= Number of door wings x people per section x rotations per minute x 60 min
Revolving door DORMA KTV-2Durchgangskapazität
When entering the door with awheelchair, several factors arerelevant for the comfortableaccessibility of the door system.The most important of all is thesize of the section. The drawingsindicate the space required forcomfortable access with awheelchair plus escort.The required dimensions for awheelchair user plus escort areestimated by the manufacturerDORMA KT-Systems, who recom-mends doors with a diameter of at least 4,200 mm for thispurpose. As a low rotationalspeed is another important factor,a disabled access pushbuttonshould be installed so that the speed may be reduced toapprox. 1 rpm in order to ensure comfortable access forwheelchair users.It should therefore be consideredduring planning, that the doorsystem has to be equipped withadditional safety sensors as anoption. The additional safetyequipment should be installedaccording to the facility operator’srequirements.
Mittelachse
700
17
00
90
08
00
Mittelachse
Mittelachse
Diameter: 3.6 m
Diameter: 4.2 m
Diameter: 4.8 m
Revolving door DORMA KTC-2Passage with wheelchair
10 KTC-2/KTV-2 GB
In the event of an emergencyactivation, the rotor returns toits starting position (parallelto façade axle) with the aid ofthe rechargeable battery pack.
As soon as the door hasreached this position, themiddle section may beopened manually in order tocreate an escape route.
The rotor travels into nightshield position on activationof the program switch. The integrated night shieldcloses both entrances of
the revolving door at thesame time.
Escape route (select escape route package). Integrated night shield.
Revolving door DORMA KTC-2DORMA KTV-2
11KTC-2/KTV-2 GB
12 KTC-2/KTV-2 GB
1234
5 6 7 8 9 10
Externalcontrol unit
Terminal X1
Equipotential bonding of at least 6 mm2
(by others)1 x 6.0 mm2
800 x 600 x 260 (mm)
(SH
)4
10
– 7
00
(LH
)2
10
0 –
22
00
Vertical sections
Wiring diagram
Drum wall with glazing Drum wall with metal panelling
Cable cross sections of up to 50 m1 Control unit cable,
25 x 0,75 mm2 without PE*2 Control unit cable,
25 x 0,75 mm2 without PE*3 Power supply line,
230 V/50 Hz, 4 x 1.5 mm2
4 Screened motor, 3 x 1.5 mm2
5 External light control, 2 x 0.75 mm2*
6 Group malfunction, 2 x 0.75 mm2*
7 Fire detector contact,2 x 0.75 mm2*
8 Power supply line,230 V/50 Hz, 3 x 1.5 mm2
9 External program switch,only as an option6 x 0.75 mm2*
10 Night-/Bank, option,2 x 0.75 mm2*
*Control unit cable withnumbered leads
All cables have to be suppliedby others 5,6,7,9 and 10 areoptions
DORMA KTC-2 Vertical sectionsWiring diagram
13KTC-2/KTV-2 GB
1234
5 6 7 8 9 10
Externalcontrol unit
Terminal X1
Equipotential bonding of at least 6 mm2
(by others)1 x 6.0 mm2
800 x 600 x 260 (mm)
Wiring diagram
Cable cross sections of up to 50 m1 Control unit cable,
25 x 0,75 mm2 without PE*2 Control unit cable,
25 x 0,75 mm2 without PE*3 Power supply line,
230 V/50 Hz, 4 x 1.5 mm2
4 Screened motor, 3 x 1.5 mm2
5 External light control, 2 x 0.75 mm2*
6 Group malfunction, 2 x 0.75 mm2*
7 Fire detector contact,2 x 0.75 mm2*
8 Power supply line,230 V/50 Hz, 3 x 1.5 mm2
9 External program switch,only as an option6 x 0.75 mm2*
10 Night-/Bank, option,2 x 0.75 mm2*
*Control unit cable withnumbered leads
All cables have to be suppliedby others 5,6,7,9 and 10 areoptions
DORMA KTV-2 Vertical sectionsWiring diagram
min
. 3
54
21
00
– 2
20
0
Vertical sections
Drum wall with glazing Drum wall with metal panelling
Axle
60°
R +
3
Detail A
Transmitted load at post:approx. 600 kg
Transmitted load at post:approx. 600 kg
Transmitted loadapprox. 400 kgrespectively
Transmitted loadapprox. 400 kgrespectively
Transmitted load at post: approx. 600 kg
Transmitted load at post: approx. 600 kg
ø 11
M 8
100
Axle
60°
50
Floor ring
Installation size (internal diameter of door system) 3600 4200 4800
Nominal radius (R) 1800 2100 2400
Floor finish (C) up to 30
All dimensions in mm.
FFL
Stainless steelangle 40 x 40 x 4 mm
C
R+3
80
– 2
50
80
– 2
50
80
– 2
50 Fill the head
space withscreed
Cross section
Floor ring KTC-2
Detail A
14 KTC-2/KTV-2 GB
DORMA KTC-2 Floor rings
R+3
Detail A
Axle
60°
Axle
60°
M 8
Floor ring
Installation size (internal diameter of door system) 3000 3400
Nominal radius (R) 1500 1700
Floor finish (C) up to 30
All dimensions in mm
FFL C
R + 3
80
– 2
50
80
– 2
50
80
– 2
50
UFLUFLUFL
Stainless steel angle 40 x 40 x 4 mm
Fill head space with screed
Cross section
Floor ring KTV-2
Detail A
DORMA KTV-2 Floor rings
15KTC-2/KTV-2 GB
16 KTC-2/KTV-2 GB
DORMA KTC-2 Safety equipment
1
1
2
5.1
11
8.28.1
3
Safety equipment KTC 2 (external control unit MS 10)
2
1
6
7
9
4
33
10
8.1 8.2
5.211
2
1
5.111
outside
inside
Schematical drawing
17KTC-2/KTV-2 GB
2 The automatic offers twoadjustments.
“Automatic I“: The doorstands still. It is started as soon as a personapproaches the doorsystem. Following anadjustable period of timethe door stops andremains in its startingposition.
“Automatic II“: The doorrotates permanently atapprox. 1 rpm. The speedis increased to approx. 3.5 rpm as soon as aperson enters the detec-tion range. Once the userhas left the detectionrange, the rotational speedis reduced again.
2 The speed limiter isactivated by means of aspecial pushbutton toreduce the speed of thedoor during passage toapprox. 2 rpm.
DORMA KTC-2 revolvingdoors offer a broad range ofsafety equipment and thusguarantee maximum safety.The main closing edges areequipped with infraredpresence sensors and safetycontact strips. As the show-case arrives at a point of lessthan 500 mm from the postprofile, the infrared presencesensors are activated inaddition to the safetycontact strips. The verticalouter edges of the nightshield are likewise protectedby safety contact strips. Theinternal area is monitoredwith the aid of an infraredlight curtain. This curtaindetects the presence of any
person or object that ismoving too slowly and wouldthus be overtaken by thewings, and will immediatelyreduce the rotational speedof the operator. If a doorwing meets an obstruction,the door is stopped until the obstruction has beenremoved.All switching paths have afailure control. Additional pre-detectionsensors are integrated intothe canopy, which scan themovement range in front ofthe moving night shield. Thedetection range is located in front of the main closingedge, from the canopy toshort above ground level.
Safety equipment Automatic functions/speed limiter
Function! Canopy sensors,
(top of door post/canopy) Cycle at low speed/Stop
" Safety contact strip(door post) Stop
§ Safety contact strip(bottom of wing) Stop
$ Safety contact strip (leadingedge of integrated night shield) Stop
¤ Emergency pushbutton(door post, inside) Stop
¤ Emergency pushbutton(door post, outside) Stop
& Limit switch for deflection device (breakout wing) Stop
/ Light barrier (bottom of wing) Stop
¤ Top sensor (top of rigid wing) Cycle at low speed/Stop
¤ Top sensor (top of breakout wing) Cycle at low speed/Stop
) Pre-detection sensor (leading edge of integrated nightshield/lower ceiling) Cycle at low speed/Stop
= Limit switch for deflection device(showcase wing) Stop
Q Disabled access pushbutton (post) Cycle at low speed
Please note:
The safety equipment has to be selected in accordance with national requirements.
Doors in accordance with DIN 18650 must contain all thebelow mentioned safety components.
8.1
8.2
5.1
5.2
2 15.2
4 1 2 5.1
3
3
6
911
8.2
8.17
11
DORMA KTV-2 Safety equipment
18 KTC-2/KTV-2 GB
1
4
3
2
5.1
11
Safety equipment KTV 2 (external control unit MS 10)
outside
inside
Schematical drawing
19KTC-2/KTV-2 GB
Safety equipment
Please note:
The safety equipment has to be selected in accordance with national requirements.
Doors in accordance with DIN 18650 must contain all thebelow mentioned safety components.
DORMA KTV-2 revolvingdoors offer a broad range ofsafety equipment and thusguarantee maximum safety.The main closing edges areequipped with infraredpresence sensors and safetycontact strips. The verticalouter edges of the nightshield are likewise protectedby safety contact strips. Theinternal area is monitoredwith the aid of an infraredlight curtain. This curtaindetects the presence of anyperson or object that ismoving too slowly and wouldthus be overtaken by thewings, and will immediatelyreduce the rotational speedof the operator. If a door
wing meets an obstruction,the door is stopped until the obstruction has beenremoved. All switching paths have afailure control. Additional pre-detectionsensors are integrated intothe canopy, which scan themovement range in front ofthe moving night shield. Thedetection range is located in front of the main closingedge, from the canopy toshort above ground level.
2 The automatic offers twoadjustments.
“Automatic I“: The doorstands still. It is started as soon as a personapproaches the doorsystem. Following anadjustable period of timethe door stops andremains in its startingposition.
“Automatic II“: The doorrotates permanently atapprox. 1 rpm. The speedis increased to approx. 3.5 rpm as soon as aperson enters the detec-tion range. Once the userhas left the detectionrange, the rotational speedis reduced again.
2 The speed limiter isactivated by means of aspecial pushbutton toreduce the speed of thedoor during passage toapprox. 2 rpm.
Automatic functions/speed limiter
Function! Canopy sensors,
(top of door post/canopy) Cycle at low speed/Stop
" Safety contact strip(door post) Stop
§ Safety contact strip(bottom of wing) Stop
$ Safety contact strip (leadingedge of integrated night shield) Stop
¤ Emergency pushbutton(door post, inside) Stop
¤ Emergency pushbutton(door post, outside) Stop
& Limit switch for deflection device (breakout wing) Stop
/ Light barrier (bottom of wing) Stop
¤ Top sensor (top of rigid wing) Cycle at low speed/Stop
¤ Top sensor (top of breakout wing) Cycle at low speed/Stop
) Pre-detection sensor (leading edge of integrated nightshield/lower ceiling) Cycle at low speed/Stop
Q Disabled access pushbutton (post) Cycle at low speed
8.1
8.2
5.1
5.2
System accessoriesDORMA KTC-2DORMA KTV-2
20 KTC-2/KTV-2 GB
Active infrared safety sensor Designation Specification
Active infrared safety sensorActive infrared systemdesigned to safeguardpassage areas and secondaryclosing edges.
Engineered to detect thepresence of people andobjects.
IRIS ON Black
External emergency pushbutton (Option)
Emergency pushbutton Designation Specification
Highly illuminated emergency pushbutton panel with visual locking status indication, acoustic and visual alarm via yellow flashlight and integrated alarm serene,sabotage-proof version, behind glass, without frame
TL-N S55 NO contact: 1, NC contact: 1,maximum load current: 1 A at24 V DC, flush-mounting, 80 x 80 mmSystem 55
TL-N S55
Designed to interrupt the automatic movement of the door.Emergency pushbutton for automatic door operators. Manu-factured according to ZH 1/494 (German Guidelines forpower-operated windows, doors and gates) and BGR 232(German Employer's Liability Insurance Association Rule) aswell as DIN 18650 (German Industrial Standard). Red knobwith yellow center insert. Maximum load current: 10 A at 230 V AC.
NAT 1 NO contact: 1, NC contact: 1, white frame,for flush-mounting, 80 x 80 mmSystem 55
NAT 4 NO contact: 1, NC contact: 1, for surface-mounting, 68 x 68 mm
NAT 1
NAT 4
IRIS ONE
Infrared safety sensor Designation Specification
4SAFE Active infrared sensor with background evaluation
4SAFE
Radar motion detector Designation Specification
Radar motion detector (Option)
Eagle
Rain protectioncover Eagle
The user-friendliness ofautomatic doors depends alot on what kind of activatoris used and on its design. The DORMA sensor rangeoffers the flexibility that is
required for the differentfields of application inconnection with reliabilityand the highest level of userfriendliness. Furthermore itprovides an effective detec-
tion of moving people orobjects in order to activate(open) automatic doors.
Standard motion detectors
Eagle 2 Standard, black
Motion detectors with direction recognitionDirection recognition for perfectly controlled opening and closing cycles
Eagle 1 Direction recognition, black
Accessories for Eagle detectors
Rain protection cover, transparent
21KTC-2/KTV-2 GB
Infrared light barriers Designation Specification
MICROCELL ONE-DL Infrared light barriers consistingof a transmitter and a receiver withround amplifier.
MICROCELL ONE-DL
System accessoriesDORMA KTC-2DORMA KTV-2
22 KTC-2/KTV-2 GB
Program switch Designation
Program switch
Program switchLockable via Euro profilehalf-cylinder (optional)
Box for surface-mountingfor program switchfor Euro profile half-cylinder (optional)
Box for flush-mountingfor program switchfor Euro profile half-cylinder (optional)
Program switch Standardlockable,mounted at door post
23KTC-2/KTV-2 GB
WN
053
53
6 5
15
32
, 0
9/0
8, K
TC-2
/KTV
-2, G
B, X.
DD
. xx
/08
· S
ubje
ct t
o ch
ange
wit
hout
not
ice
www.dorma.com
Door Control
Automatic
Glass Fittings andAccessories
Security/Time andAccess (STA)
Movable Walls
Automatic Division worldwideDORMA GmbH + Co. KGDORMA Platz 1D-58256 EnnepetalPhone +49 2333/793-0Fax +49 2333/793-495
Region AustralasiaAUS, NZ
AustraliaDORMA Automatics Pty. Ltd.Phone +61 3 97964111www.dorma.com.au
New ZealandDORMA Automatics Pty. Ltd.Phone +61 3 97964111www.dorma.com.au
Region Central EuropeD, NL, B, LX, CH
GermanyAutomatic DPhone +49 2333 793-0www.dorma.de
NetherlandsDORMA van Duin Nederland BVPhone +31 488 418 100www.dorma.nl
BelgiumDORMA foquin N.V./S.A.Phone +32 50 312849www.dorma.be
LuxembourgLuxembourg Subsidiary AutomaticPhone +49 2333 793-216www.dorma.de
SwitzerlandDORMA Schweiz AGPhone +41 71 8864646www.dorma.ch
Region Emerging MarketsP, RUS, UA, BG, GR, TR, IND, IL, RSA
PolandDORMA Polska Sp. z o.o.Phone +48 22 736-59-00www.dorma.pl
RussiaRepresentative Office in RussiaPhone +7 095 2581225www.dorma.com
UkraineDORMA Representation UkrainePhone +380 44 2443897www.dorma.com
BulgariaDORMA BulgariaPhone +359 2 9714 904www.dorma.com
GreeceDORMA Representation GreecePhone: +30 21 09944388www.dorma.com
TurkeyDORMA Kapi Kontrolleri Ltd. StiPhone: +90 216 3600056www.dorma.com
IndiaDORMA Door Controls IndiaPhone +91 442 8585097www.dorma.com
IsraelDORMA GmbH + Co. KGPhone +49 2333 793-0www.dorma.com
South AfricaDORMA Door Controls (Pty.) LtdPhone +27 11 8300280www.dorma.com
Region Far EastSGP, HK, VRC, RC, MAL, RI, RP,ROK, VN, J
SingaporeDORMA Far East Pte. Ltd.No. 31 Gul LanePhone +65 62 68 76 33www.dorma.com.sg
Hong KongDORMA Door Controls Pte. Ltd.Phone +852 25034632www.dorma.com.sg
ChinaDORMA Door Controls (Suzhou)Co. Ltd.Phone +86 512 676 12481www.dorma.com.sg
TaiwanDORMA Door Controls Pte. Ltd.Phone +886 2 9182987www.dorma.com.sg
MalaysiaDORMA Emerald Entrance SystemsPte LtdPhone +65 459 5733www.dorma.com.sg
IndonesiaDORMA Emerald Entrance SystemsPte LtdPhone +65 459 5733www.dorma.com.sg
South KoreaDORMA Emerald Entrance SystemsPte LtdPhone +65 459 5733www.dorma.com.sg
PhilippinesDORMA Door Controls Pte. Ltd.Phone +632 893 40778www.dorma.com.sg
VietnamDORMA Emerald Entrance SystemsPte LtdPhone +65 459 5733www.dorma.com.sg
JapanDORMA Emerald Entrance SystemsPte LtdPhone +65 459 5733www.dorma.com.sg
Region FranceFFranceDORMA Accueil S. A. S.Phone +33 4 79348924www.dorma.fr
Region GulfSaudi Arabia, Bahrain, Kuwait,Egypt, Syria, Jordan, Lebanon, IranDORMA ARABIA Automatic Doors Ltd.Kingdom of Saudi ArabiaPhone +966 3 847 2394www.dorma.com
United Arab Emirates, Oman, QatarDORMA Middle East LLCDubaiPhone +971 4 282 4424www.dorma.com
Region North AmericaUSA, CDN, MEX
USADORMA Automatics Inc.Phone +1 301 390-3600www.dorma-usa.com
CanadaDORMA Door ControlsPhone +1 905 6701281www.dorma.com
MexicoDORMA México, S. de R.L. de C.V.Phone +52 55 5272 6937www.dorma.com
Region ScanbaltN, S, DK, FIN, LV, EST, LT
NorwayDORMA Norge A/SPhone +47 23 176800www.dorma.no
SwedenDORMA Sverige ABPhone +46 31 289520www.dorma.se
DenmarkDORMA Danmark A/SPhone +45 44 543000www.dorma.dk
FinlandDORMA Finland OyPhone +358 9 8789130www.dorma.fi
LatviaDORMA Finland OyPhone +358 9 8789130www.dorma.fi
EstoniaDORMA Representation EstoniaPhone +372 6707064www.dorma.com
LithuaniaDORMA Norge ASPhone +47 23 176800www.dorma.com
Region South AmericaBR, RA
BrazilDORMA Sistemas de ControlesPhone +55 11 41913244www.dorma.com.br
ArgentinaDORMA Sistemas deControles para Portas LtdaPhone +54 11 45051032www.dorma.com
Region South-East EuropeA, H, CZ, CS, HR, SLO, RO
AustriaDORMA AKS Automatic GmbHPhone +43 6225 8636-0www.dorma.at
HungaryDORMA AKS Automatic GmbHPhone +36 1 2065127 or 2058058www.dorma.com
Czech RepublikDORMA dverní technika CR, s.r.o.Phone +420 2 671321-78 or -79www.dorma.com
SlovakiaDORMA Slovensko spol. s.r.o.Phone +421 2 50221 283www.dorma.com
CroatiaDORMA UREDPhone +385 1 3498 422www.dorma.com
SloveniaDORMA Representation SloveniaPhone +386 2 5 30 20 10www.dorma.com
RomaniaDORMA Romania S.R.L. Phone +40 31 806 91 60www.dorma.com
Region South EuropeI, E, P
ItalyDORMA Italiana S.r.l.Phone: +39 039 244031www.dorma.it
SpainDORMA Ibérica, S.A.Phone +34 91 8757851www.dorma.es
PortugalDORMA Portugal para Portas, Lda.Phone +351 252 860 490www.dorma.com
Region UK/IrelandGB, IRL
Great BritainDORMA UK LimitedPhone +44 1462 477600www.dorma-uk.co.uk
IrelandDORMA Ireland LimitedPhone +353 1 295 8280www.dorma.com
