RG 22 SStarrmäklergerät
Pile driver with fixed leader3/2012
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 1
C D
B
A / A'
E’
RG 22 SStarrmäkler RG 22 SFixed leader RG 22 SA Max. Mäklerhöhe 25,2 m 82.7 ft
Max. mast height
A’ Min. Mäklerhöhe (in Zeichnung dargestellt) 22,4 m 73.5 ftMin. mast height (as shown on drawing)
B Schlittenhub 19,8 m 65.0 ftStroke of sledge
Zusätzlicher Hub (Zylinderhub) 2,8 m 9.2 ftAdditional stroke with cylinder
C Ausladung (minimal/maximal) 3,1 – 4,6 m 10.2 – 15.1 ftWorking radius (min. / max.)
D Heckausladung / Schwenkradius 3,79 / 3,86 m 12.4 / 12.7 ftRear distance / swing radius
Max. Rammgutlänge (abhängig vom Rüttlertyp) 22,0 m 72.2 ftMax. length of piles (depending on type of vibrator)
Mäklerverschiebung über Flur (Mäklerfußpunkt) 2,8 m 9.2 ftBottom of mast (max. position above ground)
Mäklerverschiebung unter Flur (Mäklerfußpunkt) 0,95 m 3.1 ftBottom of mast (min. position below ground)
Mäklerneigung (nach vorn / nach hinten / seitlich) 4° / 15° / 4° 4° / 15° / 4°Mast inclination (forward / backward / sideways)
Mäklerdrehung (rechts / links) 90° / 90° 90° / 90°Mast turning angle (right / left)
Vorspannkraft am Schlitten (Rammen) 400 kN 89,924 lbfCrowd force at sledge (push)
Vorspannkraft am Schlitten (Ziehen) 400 kN 89,924 lbfCrowd force at sledge (pull)
Zugkraft Hilfswinde (Zusatzaustattung) 55 kN 12,364 lbfLine pull auxiliary winch (optinal)
zul. Drehmoment 200 kNm 147,512 lbf-ftAllowable torque
E’ Höhe, drehbare Hilfswinde (optional) 0,83 m 2.7 ftHeight, turnable auxiliary winch (optional)
© RTG Rammtechnik GmbH, 3/2012RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 2
SerienausstattungStandard equipmentDieselmotor nach Abgasnorm EU Stage III B / US Tier 4iDiesel engine compliant to EU Stage III b and US Tier 4i
Temperaturgeregelte LüftersteuerungTemperature-controlled fan operating system
Vollgasautomatik für RüttlerbetriebAutomatic full throttle control for vibrator operation
Stapelbare Gegengewichte (2 x 4,9 + 2 x 1,8 t)Stackable counterweight blocks (2 x 10,802 + 2 x 3,968 lb)
Ballastablegevorrichtung über den MastCounterweight lowering facility with lowered mast
BordwerkzeugsatzOn-board tool set
Bordbeleuchtungssatz (4 Scheinwerfer)On-board lighting set (4 spotlights)
Elektrische BetankungspumpeElectric refuelling pump
Diagnoseleiste für hydraulische FunktionenDiagnostic panel for hydraulic functions
Integrierter Schallschutz durch autom. ausfahrende SeitenklappenIntegrated noise insulation by autom. retractable side flaps
Trittroste (neben der Kabine)Catwalk (on side of operator’s cab)
MastneigungsautomatikAutomatic alignment of mast
Rohrbruchsicherungen für alle ZylinderPipe burst protection for all cylinders
ParallelogrammkinematikParallelogram kinematic linkage system
Betrieb von EntspannungsbohrantriebenPreboring mode
Hydr. Verbolzung der Mäkler-Schwenkeinrichtung mit ZylinderHydraulical bolting of mast swing mechanism with cylinder
MastabstützungVertical mast support
2. Schwenkwerk für erhöhtes SchwenkbremsmomentSecond swing drive for increased swing breaking torque
Hydraulisch verklemmbarer Teleskopunterwagen UW 70 RExtendable undercarriage UW 70 R with hydraulic clamping
BAUER Komfortfahrerkabine mit getönten Seitenscheiben und Schiebetür mit integriertem Schiebefenster
BAUER high-comfort operator cab with tinted side windows and sliding entry door with integrated sliding window
Farbdisplay mit Touchscreen Monitor ohne DatenaufzeichnungColour display on touchscreen monitor without data recording
Radio mit CD PlayerRadio with CD player
KlimaanlageAir conditioning system
ArbeitsgeräteerkennungAutomatic front-end equipment recognition
ZusatzausstattungOptional equipmentEco-Mode für DieselmotorEco-Mode for Diesel engine
DieselpartikelfilterDiesel particulate filter
KältekitArctic kit
ZusatzscheinwerferAdditional spotlights
RückfahrkameraVideo camera for reverse movement control
Absturzsicherung / Begehung am OberwagenFall protection / walkways with handrails on upper carriage
Werkzeugkasten vor FahrerkabineToolbox in front of operator's cabin
Kompressor oder GeneratorCompressor or generator
Hilfswinde 55 kN (90° drehbar)Auxiliary winch 12,365 lbf (90° rotation)
ZentralschmierungCentral lubrication
Bioölbefüllung (Panolin)Bio-degradable oil (Panolin)
Vorbereitung für zusätzl. Verfahren (Hydraulik und Steuerung)Pre-equipped for add. systems (hydraulic and control installations)
Schwenkbremse für Mäkler-SchwenkeinrichtungSlew brake for mast swing mechanism
Automatisches Kupplungssystem für das Grundgerät (ACS I) und alle Anbaugeräte (ACS II)
Automatic coupling system for hydraulic connections of the main carrier (ACS I) and all attachments (ACS II)
AutomatikvorschubAutomatic crowd
B-TRONIC Maschinendaten Erfassungs- und AufzeichnungssystemB-TRONIC Machine operating data acquisition and
recording system
Vorbereitung SchutzbelüftungPre-equipped for pressurized air conditioning system
Standheizung mit ZeitschaltuhrIndependent cab heater with time switch
Klimaautomatik (BAUER-Climatronic)Automatic air-conditioning system (BAUER Climatronic)
Kabine mit einschiebbarer FrontscheibeOperator´s cab with retractable windscreen
Schutzgitter für Dach- und/oder FrontscheibeProtective guard for roof window and/or front windscreen
Premium FahrersitzPremium operator seat
Zusätzlicher Sonnenschutz über Sonnensegel klein/großSun canopies (small/large) for additional sun protection
RG 22 S
© RTG Rammtechnik GmbH, 3/2012 RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 3
RG 22 S
© RTG Rammtechnik GmbH, 3/2012RG 22 S
Trägergerät BS 65 RS Base carrier BS 65 RS
Unterwagen UW 70 R Undercarriage UW 70 RA Breite Unterwagen 3,00 – 4,50 m 9.8 – 14.7 ft
Crawler width
B Kettenbreite 700 mm 2.3 ftWidth of track shoes
C Oberwagenbreite 3,00 m 9.8 ftWidth of uppercarriage
D Turasabstand 4,40 m 14.4 ftWheel distance
E Laufwerkslänge 5,35 m 17.6 ftOverall crawler length
Laufwerk B 6 B 6Crawler
Zugkraft 504 kN 113,304 lbfTowing force
Fahrgeschwindigkeit 0 – 1,46 km/h 0 – 0.91 mphCrawler speed
Hydraulische Verklemmung der Teleskopholme am UnterwagenHydraulic clamping device between telescopic cross beams and undercarriage body
Oberwagen Uppercarriage
Standard OptionDiesel-Motor (wassergekühlt) CAT C18 CAT C18Diesel-engine (water-cooled) EU Stage III B / US Tier 4i EU Stage II / US Tier 2
Standard-Mode ECO-Mode Standard-Mode ECO-Mode
Leistung 563 kW < 563 kW 570 KW < 570 kWRated output 755 HP < 755 HP 764 HP < 764 HP
Drehzahl 1.800 U/min 1.600 U/min 1.800 U/min 1.600 U/minRotation speed 1,800 rpm 1,600 rpm 1,800 rpm 1,600 rpm
Spezifischer Verbrauch 213 g/kWh 204,9 g/kWh 200,5 g/kWh 199 g/kWhSpecific consumption 0.350 lb/hp·h 0.337 lb/hp·h 0.329 lb/hp·h 0.327 lb/hp·h
Max. hyd. Volumenstrom 850 l/min 755 l/min 850 l/min 755 l/minMax. hydr. flow rate 224.5 gal/min 199.5 gal/min 224.5 gal/min 199.5 gal/min
Dieseltankinhalt 730 l 730 l 730 l 730 lDiesel tank capacity 193 gal 193 gal 193 gal 193 gal
Hydrauliktankinhalt 980 l 980 l 980 l 980 lHydraulic tank capacity 243 gal 243 gal 243 gal 243 gal
Hyddraulikölkühler 2 x 100 kW 2 x 100 kW 2 x 100 kW 2 x 100 kWHydraulic oil cooler 2 x 134 HP 2 x 134 HP 2 x 134 HP 2 x 134 HP
Rüttlerölkühler Integriert Integriert Integriert IntegriertOil cooler vibrator integrated integrated integrated integrated
Reduzierung Kraftstoffverbrauch ca. 20 % ca. 15 %Reduction of fuel consumption approx. 20 % approx. 15 %
Reduzierung Schallemission ca. 3 dB(A) ca. 3 dB(A)Reduction of noise emission approx. 3 dB(A) approx. 3 dB(A)
ED
AB
C620 mm2 ft
ECO-Mode (für Anbaugeräte mit geringerem Leistungsbedarf)• Reduzierte Motorleistung durch verringerte Motordrehzahl• Einsparung von Dieselkraftstoff durch reduzierten spezifischen
Verbrauch und angepasste Lüftersteuerung• Reduzierung der Geräuschemission
ECO-Mode (for attachment units with lower power demand)• Reduced output due to reduced nominal engine speed.• Fuel saving due to reduced specific consumption and adjustment
of controlled fan operating system• Reduction of noise emission
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 4
RG 22 S
Transportdaten Transport data
© RTG Rammtechnik GmbH, 3/2012 RG 22 S
A
C
B
D
A Transportlänge 19,1 m 62.7 ftTransport length
B Transporthöhe 3,6 m 11.8 ftHeight for transport
C Länge Laufwerk 5,35 m 17.6 ftCrawler length
D Transportbreite 3,0 m 9.8 ftWidth for transport
Gewicht * (ohne Gegengewicht) 59 t 130,073 lbWeight * (without counterweight)
Gewicht * (mit Maximalballastierung 6,0 + 4,2 + 2,0 t) 71,2 t 156,530 lbWeight * (with maximum counterweight 13,230 + 9,260 + 4,410 lb)
* ohne Zusatzausstattung / without optional equipment
Gewichtsangaben sind ca. Werte, Zusatzausrüstungen (Optionen) können dasGesamtgewicht verändern. Genaue Transportgewichte sind anzufragen.
Weights shown are approximate values; optional equipment may change the overall weight.Exact transport weights have to be inquired at your local dealer.
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 5
900
3200m
ax. H
ub /
Stro
ke 1
9780
04010
26030
22040
2850
MR 125V
RG 22 S
Anbauten Attachments
Rüttler für SpundwändeVibrator for sheet pilingRütteltiefe max.: 22,0 mVibrator depth max.: 72.2 ft
Tiefenrüttler mit SchleusenrüttlerDepth vibrator with bottom feedRütteltiefe max.: 19,0 mVibrator depth max.: 62.3 ft
625
3200m
ax. H
ub /
Stro
ke 1
7500
03730
26030
2850
TR 17
© RTG Rammtechnik GmbH, 3/2012RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 6
RG 22 S
Anbauten Attachments
SpundwandpressePress-system for sheet pilingTiefe max.: 22,0 mDepth max.: 72.2 ft
840
3200max
. Hub
/ S
troke
197
80
03950
26030
22620
2850
MPZ 700
Rammen mit Freifall Hydraulikhammer (FAMBO)Pile driving with free fall hydraulic impact hammer (FAMBO)
Rammtiefe max.: 19,7 mDriving depth max.: 64.6 ft
1100
3200
max
. Hub
/ S
troke
175
70
04210
26030
19870
2850
Fambo HR 5000
© RTG Rammtechnik GmbH, 3/2012 RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 7
RG 22 S
Anbauten Attachments
SOB Bohrverfahren mit Bauer Drehgetriebe KDK 275CFA Continuous flight auger drilling
with Bauer rotary drive KDK 275
Bohrtiefe mit Schneckenputzer max.: 20,0 mDrilling depth with auger cleaner max.: 65.6 ft
Bohrtiefe ohne Schneckenputzer * max.: 22,0 mDrilling depth without auger cleaner * max.: 72.2 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
10001000
2230022300
3200
3200
max
. Hub
/ S
troke
190
30m
ax. H
ub /
Stro
ke 1
9030
0041104110
2603026030
28502850
KDK 203SKDK 203S
© RTG Rammtechnik GmbH, 3/2012RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 8
RG 22 S
Anbauten Attachments
VdW-Bohren (Doppelkopfsystem)FOW Drilling (Double rotary drive system)
Bohrtiefe * max.: 22,0 mDrilling depth * max.: 72.2 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
800
3200
max
. Hub
/ S
troke
198
20
03910
26200
22350
2850
DKS 50/100
FDP VerdrängerbohrenFDP Full displacement pilingBohrtiefe * max.: 22,0 mDrilling depth * max.: 72.2 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
100032
00max
. Hub
/ S
troke
max
. 196
00
04110
26030
22450
2850
KDK 203S
© RTG Rammtechnik GmbH, 3/2012 RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 9
RG 22 S
Anbauten Attachments
SCM Einzel Soil Mixing mit Drehgetriebe MB 55-FSCM Single Column Mixing with rotary drive MB 55-F
Mischtiefe max.: 22,0 m Mixing depth max.: 72.2 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
870870
3200
3200m
ax. H
ub /
Stro
ke 1
9190
max
. Hub
/ S
troke
191
90
0040104010
2603026030
2253022530
28502850
MB 55FMB 55F
SMW Bodenmischen mit 3 MischpaddelnSMW Soil Mixing Wall with 3 mixing paddles
Mischtiefe max.: 20,0 m Mixing depth max.: 65.6 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
85032
00max
. Hub
/ S
troke
192
50
03960
26030
22440
2850
SMW 550
© RTG Rammtechnik GmbH, 3/2012RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 10
RG 22 S
Anbauten Attachments
CSM Cutter Soil Mixing
Mischtiefe * max.: 21,0 mMixing depth * max.: 69.0 ft
* abhängig von der Bodenfreiheitdepending on ground clearance
840
3200m
ax. H
ub /
Stro
ke 1
9020
03950
26030
22920
2850
BCM 5
© RTG Rammtechnik GmbH, 3/2012 RG 22 S
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 11
BAUER-Straße 1D-86529 SchrobenhausenTel. +49 (0)8252/97-0Fax +49 (0)8252/97-1135e-mail: [email protected]
Konstruktionsentwicklungen und Prozessverbesserungen könnenAktualisierungen und Änderungen von Spezifikation und Materialienohne vorherige Ankündigung oder Haftung erforderlich machen. Die Abbildungen enthalten möglicherweise optionale Ausstattungund zeigen nicht alle möglichen Konfigurationen. Diese Angaben und die technischen Daten haben ausschließlichInformationscharakter. Irrtum und Druckfehler vorbehalten.
Design developments and process improvements may require thespecification and materials to be updated and changed withoutprior notice or liability. Illustrations may include optional equipmentand not show all possible configurations. These and the technical data are provided as indicative informationonly, with any errors and misprints reserved.
905.670.1 3/2012
905-670-1_03-12_RG22S.qxd 30.03.2012 14:23 Uhr Seite 12