+ All Categories
Home > Documents > Rocketronics - RJ45-Adapter Patchcable X/Z Motor …...Connection diagram: DM556+60BYGH450D PUL+...

Rocketronics - RJ45-Adapter Patchcable X/Z Motor …...Connection diagram: DM556+60BYGH450D PUL+...

Date post: 15-Jul-2020
Category:
Upload: others
View: 3 times
Download: 0 times
Share this document with a friend
1
Connection diagram: DM556+60BYGH450D PUL+ PUL- DIR+ DIR- ENA+ ENA- A+ A- B+ B- +Vdc GND DM556 A+ A- B+ B- GND +VDC L N Power Supply 24- V 45 SHIELD PUL- DIR- ENA- +5V ELS 4 RJ45-Adapter Patchcable Alternative connection with RJ45-Adapter X/Z Motor X/Z Motor RJ45 ON OFF DIP-SWITCH SW1-SW3: Current Strom Sw4 Standstill current Stromabsenkung =OFF! Sw5-8: Steps/Rev Schrite/Umdrehung Steps 400 800 1600 3200 Sw5 OFF ON OFF ON Sw6 ON OFF OFF ON Sw7 ON ON ON OFF Sw8 ON ON ON ON DIP-SWITCH 1 2 3 4 5 6 7 8 Example: 400 Steps 2 1,0 - 1,5 mm 2 1,0 - 1,5 mm 60BYGH450D-02 Red/Blue Yellow/Black White/Brown Lilac/Green A+ A- B+ B- Use shielded cable Example: 4A RMS Current 2.7A 3.1A 3.5A 4.0A Sw1 OFF ON OFF ON Sw2 OFF OFF ON ON Sw3 ON ON ON ON 1. Turn down voltage of power source to 45V with the (adj) potentiometer! 2. Set Current to 4.0A RMS with DIP-Switch 1-3 ON-ON-ON 3. Set Dip Switch 4 to OFF 4. Set desired Steps with switch 5-8 1. Regeln Sie die Spannung des Netzteils auf 45V (adj-Poti) 2. Stellen Sie den Strom auf 4A RMS mit Schalter 1-3 ON-ON-ON 3. Setzen Sie Schalter 4 auf OFF (1/2 Ruhestrom) 4. Stellen Sie die gewünschte Schrittzahl mit Schalter 5-8 ein
Transcript
Page 1: Rocketronics - RJ45-Adapter Patchcable X/Z Motor …...Connection diagram: DM556+60BYGH450D PUL+ PUL-DIR+ DIR-ENA+ ENA-A+ A-B+ B-+Vdc GND DM556 A+ A-B+ B-GND +VDC L N Power Supply

Connection diagram: DM556+60BYGH450D

PUL+PUL-DIR+DIR-

ENA+ENA-

A+A-B+B-

+VdcGND

DM556

A+

A-

B+

B-

GND

+VDC

LN

Power Supply24- V45

SH

IELD

PUL-DIR-ENA-+5V

ELS 4RJ45-Adapter

Patchcable

Alternative connection with RJ45-Adapter

X/Z

Mo

tor

X/Z

Mo

tor

RJ4

5

ON

OFF

DIP

-SW

ITC

H

SW1-SW3: CurrentStrom

Sw4 Standstill currentStromabsenkung=OFF!

Sw5-8: Steps/RevSchrite/Umdrehung

Steps40080016003200

Sw5OFFONOFFON

Sw6ONOFFOFFON

Sw7ONONONOFF

Sw8ONONONON

DIP-SWITCH1 2 3 4 5 6 7 8

Example:400 Steps

21,0 - 1,5 mm

21,0 - 1,5 mm

60BYGH450D-02

Red/Blue

Yellow/Black

White/Brown

Lilac/Green

A+

A-

B+

B-

Use shielded cable

Example:4A RMS

Current2.7A3.1A3.5A4.0A

Sw1OFFONOFFON

Sw2OFFOFFONON

Sw3ONONONON

1. Turn down voltage of power source to 45V with the (adj) potentiometer!2. Set Current to 4.0A RMS with DIP-Switch 1-3 ON-ON-ON3. Set Dip Switch 4 to OFF4. Set desired Steps with switch 5-8

1. Regeln Sie die Spannung des Netzteils auf 45V (adj-Poti)2. Stellen Sie den Strom auf 4A RMS mit Schalter 1-3 ON-ON-ON3. Setzen Sie Schalter 4 auf OFF (1/2 Ruhestrom)4. Stellen Sie die gewünschte Schrittzahl mit Schalter 5-8 ein

Recommended