RockweII MANUFACTURING COMPANY 400 N. Lexinqton Ave. . Pittsburgh, Pa. 15208 ROCKWELL-DELTA 37-290 4" DELUXE JOINTER 418-02-651-0001 DATED 3- 1-72 4" DELUXE JOINTER SHOWN WITH STAND, MOT0 R, SWITCH ROD AND CASTERS INTRODUCTION Your new Rockwell Delta 4" Deluxe Jointer is a rug- gedly built precision jointer perfect for the home work- shop, cabinet shop and building site. It is equipped with a sealed, lubricated-for-life ball bearing cutter- head, double-tilt fence with positive stops at 90 de- grees and 45 degrees right and left, fully adjustable table with dovetailed ways and adjustable gibs, pre- cision ground and balanced high-speed steel knives.
Transcript
RockweII MANUFACTURING COMPANY
400 N . Lexinqton Ave. . Pi t tsburgh, Pa. 1 5 2 0 8
ROCKWELL-DELTA 37-290 4" DELUXE JOINTER
418-02-651-0001
DATED 3- 1-72
4" DELUXE JOINTER
SHOWN WITH STAND, M O T 0 R,
SWITCH ROD AND CASTERS
INTRODUCTION Your new Rockwell Delta 4" Deluxe Jointer i s a rug- gedly bu i l t precision jointer perfect for the home work- shop, cabinet shop and building site. It i s equipped with a sealed, lubricated-for-life ball bearing cutter- head, double-tilt fence wi th posit ive stops at 90 de- grees and 45 degrees right and left, fu l ly adjustable table wi th dovetailed ways and adjustable gibs, pre- c is ion ground and balanced high-speed steel knives.
8" LONG-BED
4" STANDARD JOlNTEl
1 IF YOU ARE NOT thoroughly familiar 7. ALWAYS use a push block when with the operation of Jointers, obtain jointing stock that does not give a advice from your supervisor or reasonable distance of safety for
2 . REMOVE tie, rings, watch and other 8. NEVER joint stock under 6" long. jewelry, and roll up sleeves. 9. NEVER pass hands directly over
3 ALWAYS wear safety glasses or cutterhead.
a face shield.
4, KEEP cutterhead sharp and free of all rust and pitch.
5, MAKE ALL adjustments with the power off.
6, GUARDS should be in place and used at all times.
10. ALWAYS make sure exposed cutter- head behind the fence is guarded, especially when jointing near the edge or rabbeting.
1 1. DISCONNECT jointer from the pow, source when making repairs.
12. SHUT OFF the power and clean the jointer before you leave it.
CLEANING THE JOINTER Remove the protective coating from the machined surfaces of the jointer. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover a l l unpainted surfaces with a good qua1 i ty paste wax.
ASSEMBLING STAND If you purchased the 50-329 Stand, assemble i t a s s h w n in Fig. 2. Make sure the lower shelf is fastened to the upper set of bolt holes in the legs as shown. Note the relationship of the holes and slots in both the upper and lower shelves, as shown in Fig. 2, to make sure the shelves are proper1 y assembled.
ASSEMBLING DUST CHUTE If you purchased the 50-801 Dust Chute (A), assemble i t to the upper shelf, as shown in Fig. 2, using the two screws (6) and nuts supplied. The front of the jointer wi l l be at the end of the top shelf marked (D) and the dust chute (A) points to the rear of the jointer stand, as shown.
ASSEMBLING JOINTER T O STAND Assemble the jointer to the top shelf of the stand using the three holes (C) Fig. 2. The front of the jointer w i l l be at the end of the top shelf marked (D).
ASSEMBLING MOTOR, M O T O R PULLEY A N D V-BELT Motors recommended for use with your jointer are the #60-020-1/3 HP motor with a 1/2" shaft, #60-220-1/2 HP motor with a 1/2" shaft and the #62-413-1/3 HP motor with a 5/8" shaft. If you purchased one of these motors, assemble i t to the stand as follows:
1. Fasten the motor to the lower shelf making sure the four rubber washers (A) Fig. 3, are positioned be- tween the motor and the shelf and that the shaft end of the motor i s toward the end of the shelf marked (E) Fig. 2.
Fig. 3.
-
Fig. 2 .
2. If you are using a motor with a 1/2" shaft i t is necessary to place the sleeve (B) and key (C) on the motor shaft, as shown in Fig. 3, before assembling motor pulley.
3. Assemble the Cat. No. 41-113 5/8" bore motor pulley to the motor shaft.
4. Make sure the motor pulley i s in alignment with the jointer pulley and assemble the #49560 V-belt to the two pulleys.
ASSEMBLING SWITCH R O D I f you purchased the 50-333 switch rod, insert the rod (A) through the hole i n the bracket (B) and assemble the end of the switch rod t o the toggle switch (C) using the cotter p in supplied. Then fasten the bracket (B) t o the upper shelf, as shown i n Fig. 4.
Fig. 4
1
ASSEMBLING RETRACTABLE CASTER ATTACHMENT If you have purchased the #49-363 Retractable Csster Attachment for use on the steel stand, assemble i t to the stand as follows:
THIS CAM ASSEMBLED AT FACTORY
LONQ SIDE
FOOT LEVER END OF SHAFT
1. Before assembling caster set t o stand, determine which side of the stand would be most convenient for the foot levers. The foot lever end of the shaft has a cam (A) Fig. 5, assembled i n place at the factory.
2. The shafts should be f i t ted across the narrow side of the steel stand.
Fig. 5 .
4. Assemble spring washer (A) and caster mount bracket (B) on each shaft, as shown in Fig. 6.
3. Assemble the cams (B) on both shafts (C) at hole (D) Fig. 5. Assemble one cam on each shaft. Cams on each shaft must match when assembled, as shown in Fig. 5.
Fig. 6.
SPRING WASHER
(A)
o
C A S T E R BRACKET (B)
- CAM
- - - 6 0 )
5. Assemble foot lever (A) Fig. 7, t o the end of the shaft using the pin supplied. Foot lever i s assembled to each shaft in the same manner, as shown in Fig. 7.
6. T i l t the steel stand by placing a 2 x 4 under i t so that the legs wi l l be off the floor about 2 inches.
Fig. 8.
GROUNDING INFORMATION This tool should be grounded while in use to protect the operator from electric shock. The tool i s equipped with an approved 3-conductor cord and 3-prong ground- ing type plug to f i t the proper grounding type recep- tacle as shown in Fig. 9.
FOOT LEVER
( A
Fig. 7.
7. Place spring washer (B), fibre washer (C) and caster mount bracket (D) on opposite end of shaft (E) Fig. 8. NOTE: The fibre washers(C) are to be used as shims. These washers can be placed on the shaft end opposite the foot lever and between the spring washer (B) and caster mount (D) Fig. 8.
8. Place caster mount bracket (D) and (F) with shaft (E) and foot lever (A) inside and under steel stand legs (G) Fig. 8.
9. Insert flat head machine screw (H) through hole in bracket (D) and through washer (0) steel stand leg (G) and fasten in place with washer (N) and nut (L) Fig. 8. Do not tighten nut securely at this time.
10. Fasten the other bracket (F) Fig. 8, to the Steel stand in the same manner and tighten both nuts (L) secure1 y.
11. Th is same method of application i s to be followed in assembling shaft to opposite pair of steel legs. The caster (M) can then be assembled to the attachment.
GROUNDED OUTLET BOX
GROUNDING BLADE 15 LONGEST OF] THE 3 BLADES
Fig. 9.
I 1
Fig. 10.
5
GROUNDED OUTLET BOX- ADAPTER
/ GROUNDING WIRE
An adapter, shown in F ig 10, i s available for connect- ing 3-prong grounding type plugs to 2-prong receptacles. THIS ADAPTER IS NOT APPLICABLE IN CANADA. The green grounding wire extending from the adapter,
. must be connected to a permanent ground such as to properly grounded outlet box, as shown in Fig. 10.
IN BOTH CASES MAKE SURE THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED.
OPERATING ADJUSTMENTS REAR TABLE AND KNIFE ADJUSTMENT For accurate work in most jointing operations, the rear table must be exactly level with the knives at their highest point of revolution. This means, of course, that the knives must be parallel to the table and pro- ject equally from the cutterhead.
To check this alignment proceed as follows:
1. Disconnect the jointer from the power source.
2. Raise or lower the rear table as required, by turn- ing the rear table hand lever, unti l the rear table is exactly level with the knives of the cutterhead at their highest point of revolution.
3. Place a straight edge on the rear table, extending over the cutterhead as shown in Fig. 11.
4. Rotate the cutterhead by hand. The blades should just touch the straight edge. If a knife i s too low or too high at either end, loosen the lock screws in the knife sl ightly, shift the knife unti l i t just touches the straight edge, and tighten the screws securely.
After the rear table has been set at the correct height, i t should not be changed except for special operations and after sharpening knives.
Fig. 1 1 .
Fig. 12.
When the rear table is too low, the condition w i l l be as illustrated in Fig. 13. The work w i l l be gouged at the end of the cut.
If the rear table is too high, the result w i l l be as shown in Fig. 12. The finished surface w i l l be curved.
I
- - - - - - - - - - - - - - - - .
REAR TABLE Too Low
Fig. 13.
As a f inal check of the rear table adjustment, run a piece of wood slowly over the knives for 6 to 8 inches; i t should rest firmly on both tables, as shown in Fig. 14, with no open space under the finished cut.
Fig. 14.
DEPTH OF CUT The amount of material removal by a single cut can be any thickness from a very thin shaving to 114". To adjust for depth of cut, raise or lower the front table by turning the hand knob (A) Fig. 15. The pointer and scale (B) Fig. 15, indicates the amount the table has been raised or lowered.
The pointer should point to the "0" mark on the scale M e n the front table i s exactly level with the knives at their highest point of revolution. I f the pointer re- quires adjustment, loosen the slotted screw to adjust the pointer accordingly.
Fig. 15 .
Fig. 16.
FENCE ADJUSTMENTS The fence can be moved across the table and can be ti l ted 45 degrees right or left at any posit ion on the table by means of the dual-control handle.
To move the fence across the table, pull the fence adjusting handle away f ran the machine unt i l the handle body (A) Fig. 16, engages the acorn nut (B). Loosen the nut, move the fence to the desired position, and retighten nut.
To t i l t fence move the fence adjusting handle in to- wards the machine, as shown in Fig. 16, to engage the nut. Loosen nut and t i l t the fence to the desired angle right or left, and retighten nut. When t i l t ing fence to the right, stop block (C), Fig. 16, must be moved out of the way.
The fence on your jointer features posit ive stops at the most used fence positions of 90 degrees and 45 degrees, right and left. Check the fence with a square to make sure the fence i s 90 degrees to the table. if an adjust- ment i s necessary loosen set screw (D) Fig. 16, and turn the adjusting screw (E) in or out against the stop block (C) unti l the fence i s at 90 degrees to the table. Then tighten set screw (D). Check the posit ive stops at 45 degrees right and left and adjust i f necessary.
CUTTERHEAD MAINTENANCE AND REPAIRS After considerable use, the knives w i l l become dul l and i t w i l l not be possible to do accurate work. Unless badly damaged by running into metal or other hard material, they may be sharpened as follows:
WHETTING KNIVES DISCONNECT THE MACHINE FROM POWER SOURCE. Use a fine carborundum stone; cover i t partly with paper as indicated in Fig. 17 to avoid marking the table. Lay the stone on the front table, lower the table and turn the cutter head forward unti l the stone l ies flat on the bevel of the knife, as shown. Hold the cutter head from turning, and whet the bevelled edge of the knife, stroking lengthwise by sl iding the stone back and forth across the table. Do the same amount of whetting on each of the three blades.
COVERED W I T H PAPER
WHETTING K N I V E S
SETTING KNIVES If the knives are removed from the head for replacement or regrinding, care must be used in re-setting them as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE.
2. Place a knife in i ts groove so that the rear edge of the bevel i s 1/16" from the surface of the cutterhead.
3. Slip lock-bar into place and tighten lock screws lightly.
4. Place a knife setting bar, made of a piece of hard- wood, approximately 12" long jointed straight on one edge, on the rear table, as shown in Fig. 18.
5. Rotate head backwards by hand and adjust blade unti l i t just touches the gauge.
6. Uqing bar, check blade at each end so that i t is parallel to table top and tighten the screws.
Fig. 18
7. Insert the other two knives and repeat above instruct ions.
CUTTERHEAD REPAIRS
When the knives cannot be properly- sharpened by the methods described above, they must be ground to a new bevel edge. In such case, or when bearings need replacement, remove the entire cutterhead 'with bear- ings and housings from the base and return i t to the factory.
Remove the nuts and washers (Item #52 and #53 of the parts drawing) from the studs (Item #51). L i f t the cutterhead assembly straight up and remove from the jointer. Then remove the studs from the cutterhead.
When install ing the cutterhead in the jointer tighten studs (Item #51 of the parts drawing) firmly into the bearing housing. Insert the cutterhead with studs into the jointer and firmly tighten the two nuts (Item #53 of the parts drawing).
BLADE CARE Gum and Pitch which collects on the blades causes excessive fr ict ion as the work continues, resulting in over heating the blades, less efficient cutting, and con- sequently loss of blade life. Use "Gum and Rust Remover " to wipe this off the blades.
When these blades become dull enough so that i t is noticeable when cutting, they should be resharpened. A sharp blade works easier and results in longer blade life. The penalty paid for a dull blade is less blade l i fe and greater wear and tear on a l l parts of the machine.
In time rust may appear on the table and fence and other parts of the jointer, resulting in less efficiency and accuracy of the machine. Use paste wax which can be applied t o prevent rust formation. if, however, rust has already formed on these parts use "Rust Remover" which w i l l restore the machine to i ts original accuracy when applied.
OPERATION The following directions wi l l give the beginner a start on jointer operation. Use scrap pieces of lumber to check settings and to get the feel of the operations before attempting regular work. ALWAYS USE GUARD AND KEEP HANDS AWAY FROM CUTTERHEAD.
PLACEMENT OF HANDS DURING FEEDING At the start of the cut, the left hand holds the work firmly against the front table and fence, while the right hand pushes the work toward the knives. After the cut i s under way, the new surface rests firmly on the rear table as shown in Fig. 19. The left hand should press down on this part, at the same time maintaining flat contact with the fence. The right hand presses the work forward throughout, protecting the operator against kick-back from the knives.
Fig. 19
JOINTING AN EDGE This is the most common operation for the jointer. Set the guide fence square with the table. Depth of cut should be the minimum required to obtain a straight edge. Hold the best face of the piece firmly against the fence throughout the feed.
JOINTING WARPED PIECES If the wood to be jointed is dished or warped, take l ight cuts unti l the surface is flat. Avoid forcing such material down against the table; excessive pressure w i l l spring i t while passing the knives, and i t w i l l spring back and remain curved after the cut i s completed.
JOINTING SHORT OR THIN WORK When jointing short or thin pieces, use a push block to eliminate a l l danger to the hands. Two types are shown in Fig. 20. They are easily made from scrap material.
Fig. 20 I
\
DIRECTION OF GRAIN Avoid feeding work into the jointer against the grain as shown in Fig. 21. The result w i l l be chipped and splintered edges.
Fig. 2 2
WRCNG FEED - AGAINST THE GRAIN
Fig. 21
Feed'with the grain as in Fig. 22 to obtain a smooth surface.
The arm of the front table and ledge of the rear table provide for cutting rabbets up to 114 inch deep and 4 inches wide. The operation i s illustrated in Fig. 23. The knife guard must be removed. Set the fence to con- trol the width of rabbet, measuring from the end of the knives to the face of the fence. Lower the front table to determine the depth of cut. Feed slowly when mak- ing a deep cut, to avoid splitt ing the wood. For wide cuts, make two or more passes at increasing depths. Use a push block when rabbeting the end of narrow stock.
Fig. 23
To cut a bevel, lock the fence at the required angle and run the work across the knives while keeping i t firmly against the fence and tables. Several passes may be necessary to arrive at the desired result.
When the angle i s small, there is l i t t le difference whether the fence is t i l ted to the right or left. However, at greater angles approaching 45 degrees, i t i s increas- ingly di f f icul t to hold the work properly when the fence i s t i l ted to the right. The advantage of the double- t i l t ing fence i s appreciated under such conditions.
When t i l ted to the left, the fence forms a V-shape with the tables, and the work i s easily pressed into the pocket while passing i t across the knives. If the bevel i s laid out on the piece in such direction that this involves cutting against the grain, i t w i l l be better to t i l t the fence to the right.
TAPER CUTS One of the most useful jointer operations i s cutting an edge to a taper. The method can be used on a wide variety of work. Tapered legs of furniture are a common example.
Instead of laying the piece on the front table, lower the forward end of the work onto the rear table. Do this very carefully, as the piece w i l l span the knives, and they w i l l take a "bite" from the work with a tendency to kick back unless the piece i s firmly held. Now push the work forward as in ordinary jointing. The effect is to plane off a l l the stock in front of the knives, to in- crease depth, leaving a tapered surface.
The ridge left by the knives when starting the taper may be removed by taking a very light cut according to the regular method for jointing, with the front table raised to i ts usual position.
Practice i s required in this operation, and the beginner i s advised to make tr ia l cuts on waste material. Taper cuts over part of the length and a number of other special operations can easily be done by the experienced craftsman.
I Points to observe in jointing various kinds of edges are shown in the diagram above.
common and most dangerous jointer hazard-the kick-back. The first meth- od is safer when surfacing, especially when the stock is less than 1 inch thick.
Points to Observe. Figs. 4 to 9 picture important points in jointing an edge. These are self-explanatory with the possible exception of Fig. 6. When it is necessary to joint an edge of this nature, pick out the central portion of the curve, and make the first light cut on this portion of the wood. It can be
seen that the stock has no fixed base- line; hence, it must be held firmly for this first cut. With a partial base made in this manner, succeeding cuts can be quickly made to bring the edge to a true surface.
Side Pressure. Side pressure is al- ways required in order to keep the work in contact with the guide fence, and is very important when jointing wide stock, as shown in Fig. 11. Where a considerable amount of wide work is to be handled, it is advisable to fasten
Replacement P a r t s Ref. Part No. Description No.
Base Front Table Rear Table Fence Clamp Plate w/Bolt Cross Slide Plate 1/4-28 x 1/4 Socket Set Screw 7/32 x 1-7/8 Roll Pin Stop Link Segment Key 5/32 x 1/2 Roll Pin Pointer Rod Fence Segment, Incl: Tilt Scale #4 x 3/16 Drive Screw Stop Screw 1/4-28 x 1/4 Headless Set Saew 5/16-18 x 1" Fillister Hd. Saew Washer Spring Washer Clamp Collar Clamp Nut Clamp Sleeve Fence Handle Body Cap Nut stud Spacer Handle Ball Cutterhead Pulley, Incl: 5/16-18 x 5/16 Soc. Set Screw Cutterhead. Inck Bearing Bearing Retainer for Pulley Side Bearing Retainer for Left Side
1-22 J-23 Ca t #37-802
DDL-250 FJ-321 FJ-322 960-02-012-0037 SP-2250 SP-663 SBS-46 SP-1609 SP-551 Cat. #I94 C a t #I534 c a t #I522 418-02-411-0001 SP-1702 SP-1029 J-13-S
Knife Lock Bar Spec. 1/4-24 x 1/4 Set Screw Set of Three Jointer Knives 1/4-28 x 19/32 Headless Set Screw Gib Table Adj. Nut Nameplate #4 x 3/16 Drive Screw 5/16-24 x 3/4 Hex. Hd. Screw Pointer 13/64 x 7/16 x 1/16 Steel Washer #lo-32 x 1/4 Rd. Hd. Screw 5/32 Hex. Wrench 1/8 Hex. Wrench 5/16 Open End Wrench Stud 1/4 Lockwasher 1/4-20 Hex. Nut Knife Guard, Inck Pin Spring 3/32 x 5/8 Cottsr Pin Scale #4 x 3/16 Drive Screw 3/32 x 5/8 Cotta Pin 5/16-18 x 5/16 Socket Set Saew Nameplate #4 x 3/16 Drive Screw Adj. Screw w/collar. Inck 1/8 x 3/4 Groove Pin 7/16 Fiber Washer Adj. Screw Sleeve Ball Crank, Incl: 5/16-18 x 5/16 Soc. Set Screw
IMPORTANT: Base. front and rear tables cannot be supplied separately, as the re-assembled machine would not be accurate. For true alignment, we finish-grind our jointer tables after assembly on the base. When a new table or base is required, ship the machine, less fence and knife guard, to the factory for rebuilding. The cost will be the list price for the new part plus a fixed charge for assembling and grinding the tables.
NOTE: - Cutterhead Repairs: Special tools are required to remove and replace ball bearings on the cutterhead. When the bearings or cutterhead need replacement, order a complete new cutterhead assembly #37-806, a return the old one to us for repairing for which there is nominal charge coming repair work plus a small labor charge per bearing for installing.
Knife Sharpening Seavice: Our charge for re-grinding and setting hives will be a nominal net charge per c~merhead, F. 0. R. factory.
Be sure to send the complete cutterhead assembly with bearings and housing, less pulley, by prepaid express or parcel post insured.
Cutterheads may be retumed to:
ROCKWELL MANUFACTURING COMPANY Delta Power Tool Division Tupelo, Mississippi Attention: Service Department
AVAILABLE FOR USE WITH 9" SAW / 4" JOINTER COMBINATION UNIT
Belt and Pulley Group, Incl: Motor Pulley for Jointer. Inck 5/16-18 x 5/16 Soc. Set Screw V-Belt for Jointer Motor Pulley for Saw, Inck 5/16-18 x 5/16 Soc. Set Screw V-Belt for Saw Raising Block Assembly. Inck Cutterhead Shaft Extension, Inck 5/16-18 x 5/16 Soc. Set Screw 5/16-18 x 1 1/4 Hex. Hd. Saew 5/16 x 3/4 x 1/16 Steel Washer 5/16-18 Square Nut 5/16-18 1 3/4 Carriage Bolt Raising Block V-Belt Switch Rod, Inck Clamp Assembly Rod 1/16 x 1/2 Cotter Pin Motor Pulley. Incl: 5/16-18 x 5/16 Soc. Set Screw Steel Stand and Dust Chute. Consisting of: Dust Chute, Inck #6-32 x 1/2 Rd. Hd. Mach Screw #6-32 Square Nut
C a t #50-329 Steel Stand, Incl: SP-901 5/16-18 x 1 1/4 Rd. Hd. Stove Bolt SP-1604 5/16 x 3/4 x 1/16 Steel Washer LBS-279 Motor Mount SP-1303 5/16-18 Square Nut MS -62 Spec. 5/16-24 Hex. Hd. Screw SP-1750 5/16 I n t Tooth Lockwasher SP-1206 5/16-24 Hex. Nut MS-82 Top Shelf SP-523 5/16-18 x 1 112 Rd. Hd. Mach. Screl SP-1604 5/16 x 3/4 x 1/16 Steel Washer SP-1303 5/16-18 Square Nut MS-83 Bottom Shelf 436-02-066-0019 Leg
C a t #49-363 Retractable Casters, Incl: SP-1300 5/16-18 Hex. Nut SP-1703 5/16 Lockwasher SP-5552 3/4 x 5/16 x 1/16 Fiber Washer MS-101 caster ~ o u n t SP-478 5/16-18 x 7/8 Flat Hd. Mack Screw MS-108 caster DSS-36 Fiber Washer SP-2733 5/32 x 7/8 Roll Pin MS-103 c a m MS-106 Shaft MS-109 Spring Washer SP-2732 5/32 x 1 Roll Pin MS-102 Foot Lever MS-100 Caster Mount
YOUR ROCKWELL WARRANTY Rockwell is proud of the quality of the power tools which i t sells. The component parts of our tools are inspected at various stages of pro- duction, and each finished tool is subjected to a final inspection before i t is placed in its specially designed carton to await shipment. Because of our confidence in our engineered quality, Rockwell agrees to repair or replace any part or parts of Rockwell Power Tools or Rockwell Power Tool Accessories which examination proves to be defective i n workmanship or material. I n order to take advantage of this guar- antee, the complete portable power tool or accessory, or i n the case of machinery, the part must be returned prepaid to the appropriate factory, Rockwell service center, or authorized service station for examination. This guarantee, of course, does not include repair or replacement required because of misuse, abuse, or normal wear and tear. Repairs made by other than our factory, service center, or authorized service station, relieves Rockwell of further l iabil ity under this guarantee. THIS GUARANTEE IS MADE EXPRESSLY I N PLACE OF ALL OTHER GUARANTEES OR WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO QUALITY, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE.
j
AUTHORIZED DELTA PARTS DISTRIBUTORS C A L I F O R N I A MASSACHUSETTS PENNSYLVANIA
LOS ANGELES, 90007 Rockwe l l Manufactur ing Company 2400 South Grand Avenue Phone: 213 749-0386
BOSTON, (Al ls ton) . 02134 Rockwe l l Monufacturtng Company 414 Cambrtdge Street Phone: 617 782-1700
OAKLAND, 94601 Rockwe l l Manufactur ing Company 4621 Malat Street M ICHIGAN Pos t Of f rce Box 7327 Phone: 415 535-2424 D E T R O I T (Southfseld), 48075
Rockwel l Manufocturlng Cornpony 18650 Wert Eight M l l e Road
COLORADO Phone: 313 35R-1000
DENVER. 80207 ~ o c k w e l l ' ~ o n u f a c t u r l n ~ Compony 4900 Eos t 39th Avenue
MISSOURI
Phone: 303 388-5803 N. KANSAS CITY, 64116
GEORGIA
Rockwel l Monufocturinq Company 1141 Swif t Avenue Phone: 816 221-2070
P H I L A D E L P H I A , 19120 Rockwel l Manufacturtng Camporjy 4433-37 Wh~toker Avenue Phone: 215 455-7907
PITTSBURGH, 15208 Rockwel l Manufacturlng Cornpony 400 North L e x ~ n g t o n Avenue Phone: 112 241-8400
TEXAS
D A L L A S , 75247 Rockwel l Manufacturing Company 2934 Iron R ~ d g e Street P o r t O f f l ce Box 47767
WASHINGTON
A T L A N T A (Dorovt l le) , 30340 3500 McCa l l P lace NEW YORK S E A T T L E , 98101 Phone: 404 458-2263 Rockwel l Monu fac tu r~ng Company
NEW YORK, 10013 1918 Minor Avenue
Rudolf Bass, Incorporated Phone: 206 622-4576
175 La laye t te Street, Cor. Grand Slreet HAWAII Phone: 212 CA 6-4000 WISCONSIN
HONOLULU, 96819 Rackwel l Manufacturing Company 3209 Koapako Street Phone: 808 872-049
B U F F A L O , 14204 Kor le Sow Company, Incorporated 138-150 Chncago Street, Cor. So. Pork Avenue Phone: 716 853-8053 or 853-8054
I L L I N O I S OH I 0
CHICAGO, (Melrose Pork), 60160 CINCINNATI , 45203 Rockwe l l Monufacturtng Company Rockwel l Monu fac tu r~ng Company 4533 North Avenue 906 Dal ton Street Phone: 312 921-2650 Phone: 513 24'1-2737
MILWAUKEE, 53222 Rockwel l Manu foc tv r~ng Compony 107nn West B u r l e ~ g h Street Phone: 414 774-3650
CANADA
G U E L P H . ONTARIO Rockwel l Manu lac tv r~ng Company of Conoda Ltmt ted 40 Welltngton Street Pos t O f f t c e Box 848 Phone. 907 922-2840
Authorfzed De l to Pa r t s Dlstrcbutors s tock o complete line of replacement parts. To save l i m e and sh ipp ing cost send your por ts orders to your nearest d ~ s t r l b u t o r and ~n most cases they w i l l be f i l l e d and shipped w l th in 48 hours. We do no1 f i l l ony ports orders d l r cc t from the foctory.
Gray P r in t i ng Company
R O C K P I T T S B U R G H 8 . P E N N S V L V A N I A ,
HOUMTlNG MOTORS ON STEEL STANDS
436-02-655-0001
DATED IM 4-27-59
PM-1547
All steel machine stands are drilled to accommodate the machines for which they are intended. A complete set of mounting bolts for both the motor and machine are included with each stand. All machines are easily mounted and should be tightened securely to avoid vibration. Use the furnished lock washers in all in- stances.
MOTOR MOUNTING Motors will fit on the machine stands without
the use of shim blocks. Other motors vary in height. Whenever the distance from the motor shaft to the bottom of the motor foot is less than 4% inches, a shim block will be needed. Fig. 1 illustrates the use of an easily made wooden shim block. For example, when dimension A is 3% inches, the thickness of the shim must be 1% inches in order to make up the required 4% inches.
Fig. 2 illustrates means for mounting any motor having base holes that do not fit holes as drilled into our stands.
FIO. 2
shown in Fig. 3 and then tighten the pulleys in correct alignment. V-belts require very little tension. Exces- sive tension Gauses short life of the belt and pulleys and puts undue load on the machine and motor bear- ings.
RUBBER F E E T NO. 50-353
A set of four moulded rubber feet complete with mounting screws are available under No. 353 for the benefit of those who operate their tools in apartmenl houses or on wooden floors in residences, where thc
PULLEYS AND BELTS slight noise caused by the operation of such machine: Consult your dealer for a V-belt of correct may occasionally be objectionable. These feet reducc
length to fit your stand mounted motor and machine. the noise of the machines on any surface, and take thc When the pulleys are in line and the belt tension is place of makeshift devices such as felt pads. They arc correct, V-belt drives are long wearing and efficient. moulded of live rubber of proper resiliency, and an When lining up pulleys, loosen the set screws in both supplied with plates and screws for attaching to stee the motor and machine pulleys: use a straight edge as stands.
MACHINE STAND The machine stand consists of hpper shelf, lower
shelf and four legs. These stands will vary in size, that is, the shelves will have different shapes and sizes and the legs will vary in length, but they are all as- sembled in the same manner. The cap screws and nuts used in assembling these various stands are all the same size and length. Refer to Fig. 4.
These stands are shipped knocked down. T o ship them assembled they would be very bulky and unhandy.
.
MS-61 WRENCH
MACHINE STAND ASSEMBLY
REPLACEMENT PARTS FOR STEEL STANDS
50-801 Dust Chute 50-656 Stand used on 6" Jointer, consists of 50-406 Steel Stand
50-800 Large Dust Chute 50-308 Stand, consisting of:
MS-96-3 Top ............................................ 1 MS-93-3 Panels - Front and Rear ................... 2 MS-94-3 Panels - Side ........................... .......... .. 2 MS-95-3 Legs ...................................................... 4 SP-409 5/16-18 x 1 1/4" Mach. Screw ........ 6 SP-1300 5/16-18" Hex. Nuts .......................... 16 SP-1306 1/4-20" Sq. Nuts .. 16 SP-1603 1/4" Steel Washer .............................. 16 SP-1604 5/16" Steel Washer .................... .... 6 SP-7504 1/4-20 x 5/8" Screw ...- 16
S T E E L S T A N D
50-305 50-306
*50-310 50-315 50-320 50-328 50-329 50-406 50-432 50-441 50-716 50-717 50-810 50-821 50-891 33-630 I ........... I MS- 119
50-105 Stapd, consisting of:
MS-61 Wrench 1 MS-62 5/16-24 x 1"Hey Hd. Scr. 16 436-02-066-0022 Leg 4 436-02-115-0084 Shelf 1
