Assembly & Installation Instructions for:
Packer™ Pro Hitch-Mount Cargo Carrier
PN: 59530
TM
A B
C D E
F G H
I J K
BASKET HALF B (X1)
FRONT BRACKET (X1) REAR BRACKET (X1) SHANK & 2” ADAPTER (X1)
CENTER PLATE (X1) HEX BOLT 1/4-20 (X12) FLAT WASHER 1/4 (X24)
LOCK NUT 1/4-20 (X12) CARRIAGE BOLT 3/8-16 (X2) FLAT WASHER 3/8 (X2)
Assembly & Installation Instructions for
Packer™ Pro Hitch-Mount Cargo Carrier
L M N LOCK NUT 3/8-16 (X2)
O P Q WRENCH (X1) L-WRENCH (X1)
BASKET HALF A (X1)
ANTI-RATTLE PIN & CLIP
(X1)
LOCK WASHER (X1)
ADHESIVE REFLECTOR
STRIP (X2)
Assembly & Installation Instructions for
Packer™ Pro Hitch-Mount Cargo Carrier
ALL ROLA PRODUCTS MUST BE INSTALLED PROPERLY AND SECURELY
ATTACHED TO YOUR VEHICLE. IMPROPER USE OR ATTACHMENT COULD
LEAD TO AN AUTOMOBILE ACCIDENT AND/OR BODILY HARM OR DEATH
TO YOU OR OTHERS. AS THE OWNER OF THIS PRODUCT, YOU ARE RE-
SPONSIBLE FOR PROPER INSTALLATION TO YOUR VEHICLE, CHECKING
THE ATTACHMENTS PRIOR TO USE, PRACTICING SAFE AND PROPER USE
OF THE PRODUCT, AND PERIODICALLY INSPECTING THE PRODUCT FOR
FIT, WEAR, AND DAMAGE. THEREFORE, IT IS CRITICAL THAT YOU READ
AND UNDERSTAND ALL OF THE INSTRUCTIONS, WARNINGS, CAUTIONS,
AND RECOMMENDATIONS PRIOR TO INSTALLATION OR USE.
WHAT YOU’LL NEED FOR ASSEMBLY
3
Lay Basket Half A and Basket
Half B side-by-side as shown
B A
2
Line up the holes on Front
Bracket (C) with the holes on the
front of Basket Half A and Basket
Half B.
1
Add Flat Washer (H) to Hex Bolt
(G) and feed the bolt through the
holes in the front bracket and
Basket Halves.
6
Add a second Washer (H) and a
Lock Nut ( I ).
5
Tighten the Hex Bolt and Lock Nut
until snug.
4
Repeat steps 3-5 in all six places
for Front Bracket (C). 1
2
3 4
5
6
5
9
7
Insert Shank & Adapter (E)
through Rear Bracket (D) as
shown (with adapter end still
exposed).
Line up the holes on Rear Bracket
(D) with the holes on the rear of
Basket Half A and Basket Half B.
8
Repeat steps 3-6 in all six places
for Rear Bracket (D).
1
2
3 4
5
6
On the underside of the basket,
add Flat Washer (K) and Lock Nut
(L) to each Carriage Bolt (J) and
tighten.
Lay Center Plate (F) across the
center of the basket floor, lining up
the notches with the holes in the
shank.
Feed Carriage Bolt (J) through the
notches in Center Plate (F) and
through the holes in the shank.
10
11
12
Add Lock Washer (N) to Anti-
Rattle Pin (M) as shown.
13
14
15
Add the Adhesive Reflector Strips
(Q) to the front corners of the
cargo carrier for increased
nighttime visibility.
Install the Cargo Carrier on your
vehicle by sliding the Shank of the
carrier into the receiver tube on
your vehicle as shown.
Fasten Clip to the end of the
Anti-Rattle Pin as shown.
Using Wrench (O), tighten the
Anti-Rattle pin until snug.
16
17
18
Line the holes in the adapter/
shank up with the holes in the
receiver then insert the Anti-Rattle
Pin (M).
19
USING WITH
1-1/4” RECEIVER?
Using L-Wrench (M), remove the
screw on the side of the Adapter,
then remove the adapter from the
shank.
WARNING
INCORRECT CORRECT
ALWAYS center/distribute load evenly in cargo carrier. ALWAYS securely fasten load to cargo carrier using bungees or a cargo net. NEVER transport people, animals, or flammable liquids in cargo carrier.
CAUTION
If the load or cargo carrier blocks or impairs visibility of the taillightsor turn signals, use optional light kit (part #6504).
If license plate is blocked by load or cargo carrier, relocate using existing holeslocated on the carrier.
If the cargo carrier or the contents being transported is in line with the exhaustoutlet, an exhaust tip must be used to redirect the exhaust flow away from thecargo platform or contents.
Do not lubricate threads. Bolt failure may occur due to over tightening.
Check security of load, fasteners, pin, and clip often during travel.
Severe bumps can damage your towing vehicle, hitch, and cargo carrier.Drive slowly on rough roads.
Stop and make a thorough inspection if your cargo carrier strikes the road.Correct any problems before resuming travel.
Do not carry loads wider than your vehicle.
The cargo carrier load rating is the LOWEST of the following:• Cargo carrier rating (500 lb with 2” Shank; 300 lb with 1-1/4” Shank)• Hitch tongue weight rating• Vehicle manufacturer tongue weight rating
Service Kits & Optional Accessories
Available for your
Packer™ Pro Hitch-Mount Cargo Carrier
Part No.: 59916
Aluminum 1-1/4” to 2” Adapter
Part No.: 59915
Anti-Rattle Pin & Clip
Part No.: 59917
Wrench
Part No.: 6504
Incandescent Light Kit
Part No.: 7330
Cargo Net
Part No.: 59200
Flat Strap Cargo Net