Roll-off container covers are a LIGHTWEIGHT, DURABLE, AFFORDABLE solution for covering the contents of roll-off containers.
FEATURES & BENEFITS
•Open to 90 degrees for easy access to entire container
•Lockable to protect container from theft and unauthorized dumping
•Built with UV-protected, impact-resistant high density polyethylene (HDPE)
•Standard design is permanently mounted and travels with the container at all times
Meets EPA regulations for
storm water exposure.
ROLL-OFF CONTAINER COVER
877.468.9278 [email protected] www.wastequip.com
Available in 3 custom configurations:
Standard- Cover is permanently mounted and travels with the container.
Stand-alone- Cover is mounted on a frame attached to existing concrete slab or footing. The stand-alone configuration allows containers to be swapped out from underneath cover.
Removable- Cover includes clamp on hinges and fork pocket frame for easy transfer to other containers.
ROLL-OFF CONTAINER COVER
Ability to maintain total container functionality even when cover is securely fastened.
ROLL-OFF CONTAINER COVER
Integrated forklift pockets molded into cover make transferring fast and easy.
Opens to 90 degrees for access to entire container.
To ensure proper opening and closing functionality there will be a gap of up to 2” between the cover and top of container
Tel: 877.468.9278 | [email protected] | www.wastequip.com
Wastequip is the leading North American manufacturer of waste and recycling equipment for collecting, processing and transporting recyclables and solid or liquid waste. © July 2015 Wastequip, all rights reserved. Specifications subject to improvement without notice. Equipment displayed should be operated by properly trained personnel. Operators should become familiar with OSHA, ANSI and any other applicable standards or laws for using this equipment. Improper use, misuse, or lack of maintenance could cause injury to people and/or property. Photos used in the literature are illustrative only. Wastequip assumes no liability or responsibility for proper training/operation of equipment not manufactured by Wastequip. We reserve the right to make changes at any time without notice. Information contained within this literature is intended to be the most accurate available at time of printing.
WQP102-072015
Available for order:
• Pre-installed on new Wastequip roll-off containers
• Sold separately for mounting on existing containers
MODEL # DESCRIPTION
220085 Roll-Off Cover with permanent mount length more than 12’ and up to 23’
2200XRO Removable Option for Roll-Off Cover (Includes Clamp-on Hinges and Fork Pocket Frame to make the cover easily removable)
2200XSO Stand-alone Option for Roll-Off Cover (Includes Mounting Frame to existing concrete slab or footings)
1
1
2
2
3
3
4
4
A A
B B
SHEET 1 OF 1
DRAWN
APPROVED
TJB 6/17/2014
DWG NO
TITLE
CONTAINER COVER
SIZE
B
SCALE
REV
A
TOLERANCES UNLESS SPECIFIED
UNITS = INCHES
X.X ` 0.1
X.XX ` 0.06
X.XXX ` 0.030
X.XXXX ` 0.0010
FRACTIONS ` 1/16
ANGLES ` 0.5°
THIS PRINT IS THE PROPERTY OF TB INDUSTRIES, INC. THIS
DRAWING REPRESENTS A PROPRIETARY ARTICLE(S) IN WHICH
TB INDUSTRIES, INC. RETAINS ALL AND ANY RIGHTS,
PATENT(S) OR OTHERWISE, TO INCLUDE EXCLUSIVE RIGHTS
TO USE, MANUFACTURE, AND/OR SELL. POSESSION OF THIS
PRINT DOES NOT CONVEY ANY PERMISSION TO REPRODUCE
PRINT OR MANUFACTURE THE ARTICLE(S) SHOWN HERE-IN.
SUCH PERMISSION MAY ONLY BE GRANTED BY SPECIFIC
AUTHORIZATION IN WRITING, SIGNED BY AN AUTHORIZED
AGENT OF TB INDUSTRIES, INC. SPECIFICATIONS MAY NOT BE
ALTERED OR SUBSTITUED WITHOUT WRITTEN APPROVAL
FROM TB INDUSTRIES, INC.
TB INDUSTRIES, INC.
100"
24"
264STANDARD DIMENSION "
CUSTOM LENGTHS AVAILABLE UPON REQUEST
Locks to keep contents
safe and prevent unauthorized
dumping.
ROLL-OFF CONTAINER COVER