+ All Categories
Home > Documents > Roll Out Bakeware Organizer #430221 - Lynk Inc · Roll Out Bakeware Organizer #430221 3Tighten...

Roll Out Bakeware Organizer #430221 - Lynk Inc · Roll Out Bakeware Organizer #430221 3Tighten...

Date post: 20-Jul-2020
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
2
Using tool provided, securely tighten finger nuts. Attach dividers to base using finger nuts. Divider (4) Base Finger Nut (8) Finger Nut (8) Tool Dividers (4) Base Glide Frame Discard (4) Parts Bag Finger Nut (8) Tool Instructions Alignment Guide Mounting Screw (4) Wood Screw (4) Parts Bag Includes © 2016 Lynk, Inc. 8241 Melrose Dr. Lenexa, KS 66214 430221 Roll Out Bakeware Organizer R2 1 Roll Out Bakeware Organizer #430221 Tighten 3 Assemble 2 1 Unpack
Transcript
Page 1: Roll Out Bakeware Organizer #430221 - Lynk Inc · Roll Out Bakeware Organizer #430221 3Tighten 2Assemble 1Unpack. Set assembled dividers back onto glide frame with mounting holes

Using tool provided, securely tighten finger nuts.

Attach dividers to base using finger nuts.

Divider (4)

Base

Finger Nut (8)

Finger Nut (8)

Tool

Dividers (4)BaseGlide Frame

Discard (4)

Parts Bag

Finger Nut (8)

Tool

Instructions

Alignment Guide

Mounting Screw (4)

WoodScrew (4)

Parts Bag Includes

© 2016 Lynk, Inc. 8241 Melrose Dr. Lenexa, KS 66214 430221 Roll Out Bakeware Organizer R2 1

Roll Out Bakeware Organizer #430221

Tighten3

Assemble2

1 Unpack

Page 2: Roll Out Bakeware Organizer #430221 - Lynk Inc · Roll Out Bakeware Organizer #430221 3Tighten 2Assemble 1Unpack. Set assembled dividers back onto glide frame with mounting holes

Set assembled dividers back onto glide frame with mounting holes in dividers and glide frame aligned.

Attach dividers to glide frame using mounting screws.

Only gently tighten.

Remove assembled dividers from glide frame.

Move inner glide rails slightly forward as shown.

Mount glide frame into cabinet usingwood screws found in parts bag.

•The use of a power screwdriver

•Drill 4 starter holes using a 1/8”

diameter drill bit.

Recommended:

Install front screws first

Base

mounting

hole

Move glide

rails forward

Set the assembled dividers and base onto glide frame with mounting holes aligned.

Check for adequate cabinet & door clearance.

Adjust glide frame position if needed.

2” min.50.8mm

2” min.50.8mm

2” min.50.8mm

Make sure arrows are pointing to the front of the cabinet

Alignment Guide

Align glide frame in cabinet as shown using alignment guide found in parts bag.

2” min.50.8mm

2” min.50.8mm

2” min.50.8mm

4 5Aligning Glide Frame Checking Cabinet Clearance

6 Mounting Glide Frame

Attach Dividers7

© 2016 Lynk, Inc. 8241 Melrose Dr. Lenexa, KS 66214

LIMITED WARRANTY AND DISCLAIMER OF LIABILITY

The manufacturer warrants this product against defects in manufacturing and workmanship for a period of ninety (90) days from the date of purchase. For questions, call (800) 733-5965 for customer service.

MANUFACTURER DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH REGARD TO THE PRODUCT. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL, CONSEQUENTIAL OR PECUNIARY LOSS), OR FOR ATTORNEY’S FEES OR COSTS, ARISING OUT OF THE USE OR OPERATION OF THE PRODUCT.

If you have questions, please call 800-733-5965

430221 Roll Out Bakeware Organizer R2

www.lynkinc.com

2

Turn screws until just snug


Recommended