RS-D7R SYSTEM CONTROL TUNER/CD OPTICAL DIGITAL REFERENCE SYSTEM RS-D7R · RS-D7R — /EW5 3 56 7 8...

PIONEER CORPORATION 4-1, Meguro 1-chome,PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, LonPIONEER EUROPE NV Haven 1087, Keetberglaan 1, 912PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253

PIONEER CORPORATION 2006

RS-D7R—/EW5

Meguro-ku, Tokyo 153-8654, Japang Beach, CA 90801-1760, U.S.A.

0 Melsele, BelgiumAlexandra Road, #04-01, Singapore 159936

ORDER NO.

CRT3659

SYSTEM CONTROL TUNER/CD OPTICAL DIGITAL REFERENCE SYSTEM

RS-D7R———— /EW5

This service manual should be used together with the following manual(s):

Model No. Order No. Mech.Module Remarks

CX-961 CRT2503 H2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

—

K-ZZW.OCT. 2006 Printed in Japan

C

D

F

A

B

E
1 2 3 4
SAFETY INFORMATIONThis service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair

Improperly can the safety and reliability of the product and may void the warranty.If you are not qualified the repair of this product properly and , you should not risk trying to do so

1. Safety Precautions for those who Service this Unit.

• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable

results.

Caution:

1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.

2. During repair or tests, do not view laser beam for 10 seconds or longer.

3. Specifications of Laser Diode

Specifications of laser radiation fields to which human access is possible during service.Wavelength = 800 nanometers

2. A “CLASS 1 LASER PRODUCT” label is affixed to the

bottom of the player.

CLASS 1LASER PRODUCT

CD MECHANISM MODULE section precaution1. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit.2. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (short pin) by referring to "the DISASSEMBLY".3. After replacing the pickup unit, be sure to check the grating.

- Service Precautions

1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction.

RS-D7R—/EW521 2 3 4

C

D

F

A

B

E

5 6 7 8

[Important Check Points for Good Servicing]In this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.

1. Product safety

Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed.

When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.

7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.

0 Safe environment should be secured during servicing.

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.

2. Adjustments

To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.

4. Cleaning

For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

RS-D7R—/EW5 35 6 7 8

C

D

F

A

B

E

1 2 3 4

CONTENTS SAFETY INFORMATION..................................................................................................................................... 21. SPECIFICATIONS ............................................................................................................................................ 52. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6

2.1 PACKING ................................................................................................................................................... 62.2 EXTERIOR(1) ............................................................................................................................................ 82.3 EXTERIOR(2) .......................................................................................................................................... 102.4 CD MECHANISM MODULE..................................................................................................................... 12

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM.......................................................................................... 143.1 BLOCK DIAGRAM ................................................................................................................................... 143.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 163.3 CD MECHANISM MODULE..................................................................................................................... 223.4 MASTER CLOCK UNIT ........................................................................................................................... 263.5 KEYBOARD UNIT.................................................................................................................................... 28

4. PCB CONNECTION DIAGRAM ..................................................................................................................... 304.1 AUDIO CONTROL PCB........................................................................................................................... 304.2 CD CORE UNIT ....................................................................................................................................... 344.3 MASTER CLOCK UNIT ........................................................................................................................... 364.4 KEYBOARD UNIT.................................................................................................................................... 384.5 OPT PCB AND SWITCH PCB ................................................................................................................. 40

5. ELECTRICAL PARTS LIST ............................................................................................................................ 416. ADJUSTMENT ............................................................................................................................................... 51

6.1 MASTER CLOCK ADJUSTMENT............................................................................................................ 516.2 CD ADJUSTMENT................................................................................................................................... 526.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 546.4 ERROR MODE ........................................................................................................................................ 566.5 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 59

7. GENERAL INFORMATION............................................................................................................................. 607.1 DIAGNOSIS ............................................................................................................................................. 607.1.1 DISASSEMBLY ..................................................................................................................................... 607.1.2 CONNECTOR FUNCTION DESCRIPTION.......................................................................................... 657.2 IC ............................................................................................................................................................. 667.3 OPERATIONAL FLOW CHART ............................................................................................................... 84

8. OPERATIONS ................................................................................................................................................ 85

RS-D7R—/EW541 2 3 4

C

D

F

A

B

E
5 6 7 8
1. SPECIFICATIONS

GeneralPower source ..................................................... 14.4 V DC (10.8 V to 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption .......................................... 4.0 ABackup current ............................................... 5 mA or lessDimensions (mounting size) ..................178 (W) mm x 50 (H) mm x 160 (D) mm (front face) ....................188 (W) mm x 58 (H) mm x 20 (D) mmWeight ...................................................................... 1.6 kgDigital input .................................................... Optical input (Sampling frequency: 44.1 kHz to 96 kHz)Digital output ................................................ Optical output (Sampling frequency: 44.1 kHz)

CD playerSystem .................................... Compact disc audio systemUsable discs ................................................. Compact discSignal format ...................... Sampling frequency: 44.1 kHz Number of quantization bits: 16; linearFrequency characteristics ........ 5 Hz to 20 000 Hz (± 1 dB)

FM tunerFrequency range ............................. 87.5 MHz to 108 MHzUsable sensitivity ....................................................... 9 dBf (0.8 µV/75 Ω, mono, S/N: 30 dB)50 dB quieting sensitivity ........ 15 dBf (1.5 µV/75 Ω, mono)Signal-to-noise ratio ........................ 70 dB (IEC-A network)Distortion ........................... 0.3% (at 65 dBf, 1 kHz, stereo)Frequency response .............. 30 Hz to 15 000 Hz (± 3 dB)Stereo separation ......................... 40 dB (at 65 dBf, 1 kHz)

MW tunerFrequency range ................. 531 kHz to 1 602 kHz (9 kHz)Usable sensitivity ................................. 18 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (± 9 kHz)

LW tunerFrequency range ................................. 153 kHz to 281 kHzUsable sensitivity ................................. 30 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (± 9 kHz)

Infrared Remote ControlWavelength ............................................... 940 nm ± 50 nmOutput ................................. typ; 12 nw/sr per Infrared LED

RS-D7R—/EW5 55 6 7 8

C

D

F

A

B

E
1 2 3 4
2. EXPLODED VIEWS AND PARTS LIST

2.1 PACKING

NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)

"

RS-D7R—/EW561 2 3 4

C

D

F

A

B

E

5 6 7 8

PACKING SECTION PARTS LIST

Mark No. Description Part No.

1 Cord Assy CDE7598

2 Bracket Assy CEA2346

3 Screw Assy CZE3198

4 Screw BNC40P120FTB

5 Screw BPZ30P100FTB

* 6 Polyethylene Bag CEG-127

* 7 Polyethylene Bag CZE3201

8 Bracket CZN6467

9 Base Assy CEA2799

10 Accessory Assy CEA4784

11 Screw CBA1650

12 Screw CBA1921

13 Handle CNC5395

14 Bush CNV1917

* 15 Polyethylene Bag E36-615

16 Cover CEG1064

17 Polyethylene Bag CEG1161

* 18 Battery CEX1006

19 Sub Carton CHA3167

20 Carton CHG5897

21 Contain Box CHL5897

22 Protector CHP2383




* 26 Lock Tie CNV-754

27-1 Owner's Manual(English) CRB2206

27-2 Owner's Manual(Spanish) CRB2207

27-3 Owner's Manual(German) CRB2208

27-4 Owner's Manual(French) CRB2209

27-5 Owner's Manual(Italian) CRB2210

27-6 Owner's Manual(Dutch) CRB2211

27-7 Owner's Manual(Russian) CRB2212

* 27-8 Caution Card CRP1332

* 27-9 Passport CRY1013

* 27-10 Warranty Card CRY1157

27-11 Polyethylene Bag CEG1116

28 Case Assy CXB3520

29 Remote Control Assy CXC3398

30 Filter CTX1054

31 Filter CTX1060

RS-D7R—/EW5 75 6 7 8

C

D

F

A

B

E
1 2 3 4
2.2 EXTERIOR(1)

RS-D7R—/EW581 2 3 4

C

D

F

A

B

E

5 6 7 8

EXTERIOR(1) SECTION PARTS LIST


1 Screw BSZ26P050FCU

2 •••••

3 Flat Cable CDE6627

4 Cord Assy CDE7598

> 5 Fuse(4 A) CEK1001

6 Cap CNS1472

7 Resistor RS1/2PMF102J

8 Case CNB2991

9 •••••

10 •••••

11 •••••

12 •••••

13 •••••

14 Screw BSZ26P050FCU

15 Cord CDE4107

16 Cord CDE4108

17 Cord CDE6684

18 •••••

19 Antenna Cord CDH1251

20 Shield CNC9688

21 Holder CND2224

22 Seal CNM7598

23 Insulator CNM8845



26 Spacer CNM8852

27 Audio Control Unit CWN2000

28 Connector(CN353) CDE6681

29 Cord(CN321) CDE8126

30 Clamper CEF1041

31 Terminal(CN401) CKF1064

32 Connector(CN901) CKM1500

33 Plug(CN652) CKS-783

34 Plug(CN851) CKS-786

35 Plug(CN101) CKS1044

36 Plug(CN102) CKS1045

37 Connector(CN801) CKS1085





42 Mini Pin Jack(CN451) CKX1046

43 •••••

44 Holder CNC9186

45 Holder CNC9187

46 Holder CNC9188

47 Holder CNC9451

48 Holder CNC9452

49 Holder CNC9556

50 FM/AM Tuner Unit CWE2027



53 Holder(SH1) CNC8708

54 Case CNC8713

55 Connector(CN173) HKS-193

56 Master Clock Unit CWN1766




60 Chassis Unit CXC7221

61 Screw ISS26P055FTC

62 CD Mechanism Module(H2) CXK5358


RS-D7R—/EW5 95 6 7 8

C

D

F

A

B

E
1 2 3 4
2.3 EXTERIOR(2)

RS-D7R—/EW5101 2 3 4

C

D

F

A

B

E

5 6 7 8

EXTERIOR(2) SECTION PARTS LIST


1 Panel Assy CXC7351

2 Screw BMZ20P030FTC

3 Screw BPZ20P060FTC

4 Screw(M2 x 3) CBA1061


6 Screw CBA1933


8 Screw(M1.4 x 4) CBA1942

9 Screw CBA1946

10 Spring CBH2445

11 Cord CDE5960

12 Connector CKS4436

13 Frame CNC8201

14 Spacer CNM6155

15 Spacer CNM6156

16 PCB CNP5941

17 Flexible PCB CNP6124

18 Guide CNV5696

19 Rack CNV5697

20 Gear CNV5698

21 Torque Limit Unit CNV5762

22 Cover CNV6573

23 Lighting Conductor CNV6574

24 Holder CNV6575

25 Switch(S951) CSN1012

26 Switch(S952) CSN1022

27 Arm Unit CXB3574

28 Bracket Unit CXB3577

29 Arm Unit CXB3866

30 Holder Unit CXB6726

31 Frame Unit CXB6727

32 Motor Unit(M10) CXC2489

33 Washer 2-1816-0035-D2-00

34 Washer 2-1821-0045-D2-00

* 35 Panel CNS8707

36 Remote Control Assy CXC3398

37 Lower Case CNS8028

38 Detach Grille Assy CXC6140

39 Screw BPZ20P100FTB

40 Button CAC6862

41 Cushion CNM7548

* 42 Cover CNS8709

43 Flat Cable CDE6700



46 Spacer CNM7397

47 Seal CNM7549

48 Spacer CNM9191

49 OEL Module MXK8203

50 Sub Grille Assy CXC6141

51 Knob Unit(VOLUME) CXC6209

52 Spring CBL-108

53 Button assy(SELECT) CXC6210

54 Screw(M2 x 2.5) CBA1609

55 Panel CNS8708

56 Holder CNC8659

57 Cover CNM9146

58 Cushion CNN1687

59 Motor CXM1217

60 Gear CNV5761

61 IC(IC1881) TSOP4840SB1


RS-D7R—/EW5 115 6 7 8

C

D

F

A

B

E
1 2 3 4
2.4 CD MECHANISM MODULE

83

85

111

108109

110

GEM1030

GEM1030

GEM1029

C

RS-D7R—/EW5121 2 3 4

C

D

F

A

B

E

5 6 7 8

CD MECHANISM MODULE SECTION PARTS LISTMark No. Description Part No.

1 CD Core Unit CWX3369 2 Connector(CN101) CKS4939 3 Connector(CN901) CKS5248 4 Connector(CN701) CKS5091 5 Screw BSZ20P035FTC

6 Screw(M2 x 4) CBA2037 7 Screw(M2 x 2.5) CBA1974 8 Screw(M2 x 3) CBA1762 9 Screw(M2 x 6.2) CBA1763 10 Washer CBF1037

11 Washer CBF1064 12 Spring CBH2291 13 Spring CBH2292 14 Spring CBH2293 15 Spring CBH2295

16 Spring CBH2297 17 Spring CBH2298 18 Spring CBH2299 19 Spring CBH2303 20 Spring CBH2304

21 Spring CBH2305 22 Spring CBH2308 23 Spring CBH2309 24 Spring CBH2332 25 Spring CBH2416

26 Spring CBH2434 27 Spring CBL1448 28 Spring CBL1466 29 Connector CDE6099 30 Shaft CLA3683

31 Shaft CLA3684 32 Lever CNC8501 33 Bracket CNC8507 34 Bracket CNC8509 35 Cushion CNM6301

36 Sheet CNM6773 37 Sheet CNM6774 38 Gear CNR1559 39 Arm CNV5928 40 Arm CNV5929

41 Gear CNV5930 42 Gear CNV5932 43 Gear CNV5931 44 Gear CNV5933 45 Holder CNV5943

46 Holder CNV5944 47 Arm CNV5948 48 Cover CNV5950 49 Holder CNV5951 50 Holder CNV6222

51 Holder CNV6223 52 Damper CNV6426 53 Holder CNV6446 54 Holder CNV6512 55 Chassis Unit CXB4501

56 Arm Unit CXB4503 57 Motor Unit(M3) CXC6003

58 Screw(M2 x 1.2) CBA1760 59 Guide CNV5925 60 Arm Unit CXB5311

61 Loading Arm Assy CXB5715 62 Washer CBF1060 63 Spring CBH2170 * 64 Shaft CLA3678 * 65 Gear CNV5934

66 Roller CNV6068 67 Holder CNV6210 68 Collar CNV6439 69 Arm Unit CXB5686 70 Washer YE20FTC

71 Washer CBF1038 72 Arm CNC8498 73 Lever Unit CXB4502 74 Screw(M2 x 1.5) CBA1761 75 Frame CNC9417

76 Sheet CNM6951 77 Guide CNV5924 78 Washer CBF1037 79 Spring CBH2300 80 Spring CBL1446

81 ••••• 82 Spacer CNM6467 83 Spacer CNR1189 84 Guide CNV5945 85 Clamper CNV6767

86 Arm CNV5947 87 Lever CNV5949 88 Arm Unit CXB4505 89 Screw JFZ20P020FTC 90 Frame CNC9416

91 Damper CNV6426 92 Screw ISS20P060FTC 93 Screw(M2 x 3) CBA1762 94 Holder CNV6341 95 Roller CNV6389

96 Arm Unit CXB5970 97 Roller CNV6389 98 Armunit CXB5971 99 Load Motor Assy(M2) CXC5821 100 Carriage Motor Assy(M1) CXC5819

101 Screw Unit(-B) CXB6363 102 Screw ISS20P060FTC 103 Screw JFZ20P025FNI 104 Washer YE15FUC 105 Pickup Unit(Service)(P8) CXX1305

106 Screw IMS20P030FTC * 107 Cover CNC9151 108 Screw BMZ26P030FTC 109 Cord CDE8349 110 Spacer CNM7805

111 Sheet CNC9466 112 Connector(CN301) CKS4439


RS-D7R—/EW5 135 6 7 8

C

D

F

A

B

E

IC 25174HCT157

SELECTO

1

UTE

K1 SRCIC 261

SM5849B

t

NIX

XO

UT

O

EL

DIRIC 221

9055WHS

DO

UT

/BC

KO

/LR

CO

X22112.288MHz

23 22

Q931

32

Q174

BUP

Q1

Q803

Q801

Q806

Q951

6

Q911

1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM3.1 BLOCK DIAGRAM

TC

166

MCK1

22DM

63MC

47dgrs

243414

AUDIDERRDIRSCDTX

LC8

46

52

X1

26753

100SP641

TXRXIPPW

868527

ASENBO28

SYSTEMCONTROLLER

IC 601 (2/2)PE5208A1

ISENS91

FLPPWR22

16

15X601

12.58291MHzX2

Q9

Q805

SYSPWR

ELPILM

21

TELIN4

RXDTXD

ROT0ROT1

95966364

OELPW25

23

BUP

Q804

Q808

BUP BUP

SWVDD1

Q802

ILMPWR24

Q807

FM/AM TUNER UNIT

MAINANT

CN451

Q103

711

8

451

CN101BUSL1BUSL2

ASENB1

1187415

CN102

IC 102TA2050S

12

3

IC 101HA12187FPS1

IP-BUS DRIVER65

12

TXRX

IPPW8

Q101

Q102

BUP

IC 103TC7S04FU

INVERTER

4 2

VCC BUP

Q853

FLPOPNFLPCLS

4342

FCLSSW

FOPNSW

45

44

Q851

Q852

IC 851BA6288FS

314

611

IC 961S-80834CNUA-B8T

RESET

1

MAUTOMATIC FLAP

MOTOR AND SENSE

VDDQ962

Q991

VDBUP

Q998

CN851

83

54

3

2

1

CN651CN701

CD CORE UNIT

M

LASERDIODE

MONITORDIODE

FOCUS ACT.

CARRIAGEMOTOR

MLOADINGMOTOR

SPINDLEMOTOR

TRACKING ACT.

LD(–)

MD+5V

FO+

TO+

17

5

3

4

PICKUP UNIT(SERVICE)(P8)

HOLOGRAM UNIT

IC 401BA5811FM

IC 301TC9495F2S1

IC 801BA05SFP

+5VREGULATOR

15

SPDIFG

15

8VD

VD

V+5

5CONT

CDEJET

CDLOAD

5

13CD5VON

13

CN901

CN101

AC/F/E/BD

EC

VM

VCCCONTST/SP

FG

CLAMPSW

15

16

10

22

9

1

31

1

9

X601

10

2

21MUTE

13

8

9

66

4

HOME

11

HOMESW

Q102

IC 201TA2153FNS1

RF AMP

MDI

LDO

VDV+5M

9

71210

1234

11

6

Q101

CN652

1

AVREFVDD

Q601

AUDIO CONTROL PCB

A

BUS+BUS-

SWITCHPCB

A

C

F

IC 264TC7SH02FUS1

2

4

IC 401S-812C50AUA-C3E VDDBUP

2

11RESET

VDDDALMON71

41CN301

IC 601PE5238A1

CD5VON

2

CDTX

TX

MC

K

DSCSNS

45

37358

X2 X1

9 78

DO

UT

XI

MC

K

TX

VDCONT

BSRQ

8

VDCONT48

52

1616BRST77

1717BSCK1

1818BRXEN29

1919BDATA2

2020RESET7

70

69

65

68

67

66

BSRQ

BRST

BSCK

BRXEN

BSO

BSI

VD

47

BSENS 93

ASENS92

ROMCSROMCKROMDATA

333231

IC 602PDH098A

123

IC 201PCM1800S1

ADC

SYSTEMCONTROLLER

IC 601 (1/2)PE5208A1

dgrst

DSEL

DGMUTE

NL1NL2DTSDBWTUNPCE2SLTUNPDITUNPCKSTSDTUNPCECURRQLDETLOCLLOCHTUNPDO

795860377494973938995788353698

AUDIODERR

DIRSEL

PEE

IC 122NJM4580M

2 1IC 121BA3131FS

2

47 1

CN451

SYS+8

Q401

Q154

59

TMUTE

RDS DECODERIC 501

PM4009A1

20

11

12X501

3.648MHz

Q501

VDD24

COMP

FM/AM4 5 6 7 8

rc

k

rd

slk

lde

t

RD

T

RD

S57

K

15

dr

st

Q402

NL2

Q153

Q155VDD

Q151

VDD

Q156

FM/AM 29

LDE

T

FM/A

M

IC3EEPROM

28

27

FM/AM 1ST IF 10.7 MHzT51 Q51 CF51 CF52 CF53

IC1MIXER, IF AMP, DET.

6

21

18LDET

COMP

2225 10 14 12 15 16 8 13 3

CF202

VDDVCC

DI/D

O

CE

2

CK

CE

1

SD

BW

SL

FMS

D

NL1

NL2

IC 2 FM MPX

AMANT

FMANT

ATT

ATT

AMRF

FMRF

IMG ADJ

RF ADJ

X90110.25 MHz

ANT ADJ

LOCL23

LOCH

AMDETMPXREF 41 kHz

AM 2ND IF450 kHz

19

CR

EQ

11

DG

ND

1

ST

IND

L ch

5R ch

924

NC

FMLO

CL

20177

NC

NC

WC

26 RFGND

42

RS-D7R—/EW5141 2 3 4

C

D

F

A

B

E

2

6

47

243414

04

Q808

BU

Q802

Q807

642FUS1

2

VD

5 6 7 8

OE

L M

OD

ULE

Q172

4

CN901

131215

452

CN1881

2

CN171

2

CN174IC 171

TC7WH04FU1 2

Q171IC 172

TC7SET08FUS1

KEYMATRIX

4 2

IC 301TC9271FS

DIT764

16

IC 322TC7S04FU

4

IC 302TC7SET04FUS1

2 4

14

18

IC 251TC74HCT157AF

SELECTOR497

1

2DMUTE

3MCK1 SRC

IC 261SM5849BF

3

IC 263TC7SH08FUS1

2 IC 262TC7WH34FU

4

IC 173NJM78L05UA

3

IC 941TPD1018F

6 1 BREM

ILL

TEL1

13

DINO

IC 281PD0236BM

1417DATA0

dgrst

NIX

XO

UT

AUDIODERRDIRSELCDTX

DIRIC 221

LC89055WHS-RA8

DO

UT

/BC

KO

/LR

CO

X22112.288MHz

23 22

VCC

1

6

5

Q931

Q932

Q174

SYS+B

Q921

5V

Q971

BUP

Q173

Q922

BUP

Q923

P

Q803

Q801

Q806

KYDTDPDTOELB

SWVDD8

13ILB

KYDTDPDTOELB

SWDVDD

ILB

SWDVDD

RST115

9

4

2RESRT

VDD

Q951

CN801

SWD+B

2526

64

KEYDTDSPDT

X1

X0

IC 1801PD6556A

X18013.77MHz

81

REMIN

1

45

75 4

80

IC 1881TSOP4840SB1

IC 1821PD8166A

REMOTE CONTROLSENSOR

3SWDVDD

OPT IN

IC 1802S-80929CNNB-G8Z

2SWDVDD

SWDVDD

CN1861

Q1881

KEYBOARD UNIT

A

OPT OUT

OPT IN

OPT PCB

2

CN173

2

CN172

B

E

8

3

6

2

5

DI

ACC

Q912

BUP

D

Q911

1

2BUP2

EF 901

BACKUP

GND

B.REM

ILL

ACC

MUTE

CEK10014A

3

MASTER CLOCK UNIT

SYS+B 4

3

CN353

CD5VON

D

4

3

CN1501

+8V

CD5VON Q1502

Q1501

Q1503

Q1505

IC 1502NJM431U

3

1

Q1504

Q1506

1

IC 1503NJM431U

3

Q1507X1501

16.9344MHz

IC 1501TC7SU04FU

42

IC 1504NJM431U

1,3

1

CN1502

VCC

2 5

Q1551

Q1552

IC 1551NJM431U

3

2

1

Q1554

Q1555

Q1553IC 1552NJM2373AF

5

X151116.9344MHz

14

IC 1553NJM2373AF

1

CN1551

1

CN3212

CPU_RESET

70 2 IC 1884TC7SET08FUS1

4OEL_WR


4OEL_RESET


47

12

1718

22

19

IC 1887TC74VHCT541AFK

5 IC 1883S-818A33AUC-BGN

1SWDVDD

IC 1888S-93C46BD0I-J8

23,33

IC1555MAX4412EXK

3

RS-D7R—/EW5 155 6 7 8

C

D

F

A

B

E

1881

1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

A-a

A F

A-aA-a A-b A-b

A-a A-b

A-b A-a

Large sizeSCH diagram

Guide page

Detailed page

Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".

CW

E20

27

C CN301

C CN701

E CN

MAUTOMATIC

FLAP MOTORCXC2489

M10S951CSN1012

CLOSEOPEN

S952CSN1022 F SWITCH PCB

FM

(100

%):

-20d

Bs

AM

(30%

):-3

0dB

s

I

P-B

US

(MC

D, M

DV

D):

-+2.

2dB

s

FM(100%): -7.8dBsAM(30%):-17.8dBs

IP-BUS: -1.8dBs

MA

IN A

NT

EN

NA

RS-D7R—/EW5161 2 3 4

C

D

F

A

B

E

A-a A-b

A-a A-b

A-b A-a

E

H PCB

5 6 7 8

A-b

A B

A AUDIO CONTROL PCB

Decimal points for resistorand capacitor fixed valuesare expressed as :2.2 2R20.022 R022

← ←

The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.

Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.

NOTE :

Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.

>

>

CN1881

D CN1501

D CN1551

B OPT PCB

AUDIO CONTROL UNITConsists of AUDIO CONTROL PCB OPT PCB

BACKUP

GND

B.REM

ILL

ACC

MUTE

CEK10014A

>

RS-D7R—/EW5 175 6 7 8

C

D

F

A

B

E

1 2 3 4

A-a

A-b

A-b B 1 2 3

AA

UD

IO C

ON

TR

OL

PC

B

DC

N15

01

DC

N15

51

BO

PT

PC

B

AU

DIO

CO

NT

RO

L U

NIT

Con

sist

s of

AU

DIO

CO

NT

RO

L P

CB

OP

T P

CB

RS-D7R—/EW5181 2 3 4

C

D

F

A

B

E

5 6 7 8

A-a

A-b

A-b4

Dec

imal

poi

nts

for

resi

stor

and

capa

cito

r fix

ed v

alue

sar

e ex

pres

sed

as :

2.2

2R

20.

022

R

022

←

←

The

> m

ark

foun

d on

som

e co

mpo

nent

par

ts in

dica

tes

the

impo

rtan

ce o

f the

saf

ety

fact

or o

f the

par

t.T

here

fore

, whe

n re

plac

ing,

be

sure

to u

se p

arts

of

iden

tical

des

igna

tion.

Sym

bol i

ndic

ates

a r

esis

tor.

No

diffe

rent

iatio

n is

mad

e b

etw

een

chip

res

isto

rs a

nddi

scre

te r

esis

tors

.

NO

TE

: Sym

bol i

ndic

ates

a c

apac

itor.

No

diffe

rent

iatio

n is

mad

e b

etw

een

chip

cap

acito

rs a

nddi

scre

te c

apac

itors

.

>

>

1881

BA

CK

UP

GN

D

B.R

EMILL

AC

C

MU

TE

CE

K10

014A>

RS-D7R—/EW5 195 6 7 8

C

D

F

A

B

E

WE2027

1 2 3 4

A-b

A-a

A-a

A-b B 1 2 3

CC

N30

1

CC

N70

1FM(100%):-20dBsAM(30%):-30dBs

IP-BUS(MCD, MDVD):-+2.2dBs

FM

(100

%):

-7.

8dB

sA

M(3

0%):

-17.

8dB

sIP

-BU

S:

-1.8

dBs

RS-D7R—/EW5201 2 3 4

C

D

F

A

B

E

5 6 7 8

A-b

A-b

A-a

A-a F

4

CWE2027

EC

N18

81

MA

UT

OM

AT

ICF

LAP

MO

TO

RC

XC

2489

M10

S95

1C

SN

1012

CLO

SE

OP

EN

S95

2C

SN

1022

FS

WIT

CH

PC

B

MAIN ANTENNA

RS-D7R—/EW5 215 6 7 8

C

D

F

A

B

E

330K

L

F

T

CS

S

1 2 3 4

3.3 CD MECHANISM MODULE

C

8200P

RED

BLACK

WHITE

CARRIAGE MOTORM1 CXC5819

LOADING MOTORM2 CXC5821

SPINDLE MOTORM3 CXC6003

SIGNAL LINEFOCUS SERVO LINETRACKING SERVO LINECARRIAGE SERVO LINESPINDLE SERVO LINE

SL

F

T

C

S

RF AMP

ACT / MOTOR DRIVE

5VREGULATOR

C CD CORE UNIT

PICKUP UNIT(SERVICE)(P8)

SWITCHES:CD CORE UNIT

S901 :LOAD,EJ SWITCH . . . . ON-OFFS902, 903 :LOAD,EJ SWITCH . . . . ON-OFFS904 :HOME SWITCH . . . . . . ON-OFF

The underlined indicates the switch position.

SL

SL SL

SL

SL

SL

SL

SL

SL

SL

S

F

F

F

F

F

F

F

F

F

F

F

F

F

F

F

F

F

T

T T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

C

C

C

C

C

C

C

C

C

S

S

SS

SS

1

2 3

4

5

6

7

9

0

!

#

)

RS-D7R—/EW5221 2 3 4

C

D

F

A

B

E

0P

F

T

9

5 6 7 8

C

220K

330K

33P

VDCONT

CSENS

XRST

CD5VON

DSPMUTE

BSRQ

BRST

BSCK

BRXEN

BDATA

RESET

SUBOK

R713CSENS

DSPMUTE

BSRQ R702 220

BSCK

BRXEN

BDATA

R701

220

SUBOK R711 0R0

R708

0R0

R605

22K

R606

47K

PE5238A1

R3054R7K

C314220P

MCK

TXTX

MCK

GND

GND

CN301

TX

R31

1R

321

220

0R0

TX

CD MECH. CONTROLLER

SERVO CONTROL / DSP / DAC / LPF

A

ACN652

CN651

DCN1502

SL

SL

F

T

C

C

S

SS

8

@(

)

⁄

SL

RS-D7R—/EW5 235 6 7 8

C

D

F

A

B

E

1 2 3 4

7 CH1:FD 2 V/div.8 CH2:fok 5 V/div.0 CH3:FG 5 V/div.9 CH4:SINY 5 V/div.

Setup(In focus)

- Waveforms

1 CH1:DSCSNS 5 V/div.2 CH2:CDLOAD 5 V/div.3 CH3:CDEJET 5 V/div.⁄ CH4:VD 5 V/div.

12 cm LOAD

500 ms/div.

1 CH1:DSCSNS 5 V/div.2 CH2:CDLOAD 5 V/div.3 CH3:CDEJET 5 V/div.

8 cm EJECT

500 ms/div.

4 CH1:RFO 500 mV/div.5 CH2:TEY 500 mV/div.

Tracking open

2 ms/div.1 CH1:DSCSNS 5 V/div.2 CH2:CDLOAD 5 V/div.3 CH3:CDEJET 5 V/div.

12 cm EJECT

500 ms/div.

1 CH1:DSCSNS 5 V/div.2 CH2:CDLOAD 5 V/div.3 CH3:CDEJET 5 V/div.⁄ CH4:VD 5 V/div.

8 cm LOAD

500 ms/div.

5 CH1:TEY 500 mV/div.6 CH2:FEY 500 mV/div.

Setup

200 ms/div.

100 ms/div.

7 CH1:FD 1 V/div.! CH2:FOP 2 V/div.

Setup(In focus)

200 ms/div.

6 CH1:FEY 500 mV/div.@ CH2:foon 5 V/div.

Setup(Focus close)

1 ms/div.6 CH1:FEY 200 mV/div.7 CH2:FD 500 mV/div.

Setup(Focus AGC)

1 ms/div.5 CH1:TEY 200 mV/div.# CH2:TD 200 mV/div.

Setup(Tracking AGC)

1 ms/div.

GND →

GND →

GND →

GND → GND →

GND →

GND →

GND →

VREF →

VREF →

VREF →

VREF →

GND →

GND →

GND →

GND →

GND →

GND →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

7 CH1:FD 1 V/div.8 CH2:fok 5 V/div.9 CH3:SINY 5 V/div.

Setup

500 ms/div.

Note:1. The encircled numbers denote measuring pointes in the circuit diagram.2. Reference voltage

VREF:2.1 V

RS-D7R—/EW5241 2 3 4

C

D

F

A

B

E

5 6 7 8

4 CH1:RFO 0.5 V/div.

Play

0.5 µs/div.

9 CH1:SINY 100 mV/div.

Play

200 ms/div.

6 CH1:FEY 500 mV/div.7 CH2:FD 500 mV/div.4 CH3:RFO 1 V/div.

Setup(FE Bias adjustment)

10 ms/div.

5 CH1:TEY 500 mV/div.) CH2:CIN 500 mV/div.

Search

200 ms/div.

4 CH1:RFO 1 V/div.5 CH2:TEY 500 mV/div.# CH3:TD 1 V/div.

Test mode 1TRjump

500 µs/div.4 CH1:RFO 1 V/div.5 CH2:TEY 1 V/div.# CH3:TD 1 V/div.

Test mode 100TRjump

5 ms/div.

4 CH1:RFO 2 V/div.( CH2:dfct 5 V/div.7 CH3:FD 1 V/div.# CH4:TD 2 V/div.

Play(The defect part passes)

500 µs/div.

4 CH1:RFO 1 V/div.5 CH2:TEY 1 V/div.# CH3:TD 1 V/div.

Test mode 32TRjump

5 ms/div.

4 CH1:RFO 1 V/div.5 CH2:TEY 500 mV/div.( CH3:dfct 5 V/div.

CRG move

50 µs/div.

VREF →

VREF → VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF → VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

VREF →

6 CH1:FEY 500 mV/div.7 CH2:FD 500 mV/div.5 CH3:TEY 500 mV/div.# CH4:TD 500 mV/div.

Play

1 ms/div.

RS-D7R—/EW5 255 6 7 8

C

D

F

A

B

E
1 2 3 4
3.4 MASTER CLOCK UNIT

D

ACN353

RS-D7R—/EW5261 2 3 4

C

D

F

A

B

E

5 6 7 8

D

D MASTER CLOCK UNIT

ACN321

CCN301

RS-D7R—/EW5 275 6 7 8

C

D

F

A

B

E

ule3

1 2 3 4

3.5 KEYBOARD UNIT

E

CN

801

A

OEL ModMXK820

VOLUME

RS-D7R—/EW5281 2 3 4

C

D

F

A

B

E

OEL MMXK8

5 6 7 8

E

odule203

E KEYBOARD UNIT

RS-D7R—/EW5 295 6 7 8

C

D

F

A

B

E

80

FM/A

1 2 3 4

4. PCB CONNECTION DIAGRAM4.1 AUDIO CONTROL PCB

A

A AUDIO CONTROL PCB

CapacitorConnector

P.C.Board Chip PartSIDE B

SIDE A

NOTE FOR PCB DIAGRAMS1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram.2.Viewpoint of PCB diagrams

10 20 30 40 50 60 70X

140

130

120

110

100

90

80

70

60

50

40

30

20

10

0

Y

D CN1501

B CN173

FM10

D CN1551

OPT IN

IP-B

US

IN

IP-B

US

OU

T

1

2

3

4

RS-D7R—/EW5301 2 3 4

C

D

F

A

B

E

70

5 6 7 8

A

SIDE A

80 90 100 110 120 130 140 150 160 170

FRONT

FM/AM TUNER UNIT

C CN301

C CN701

E CN1881

MAIN ANTENNA

CORD ASSY1 1

RS-D7R—/EW5 315 6 7 8

C

D

F

A

B

E

8

1 2 3 4

A

A AUDIO CONTROL PCB

90100110120130140150160170

TESTIN

PCL

11

RS-D7R—/EW5321 2 3 4

C

D

F

A

B

E

90

5 6 7 8

A

SIDE B

1020304050607080 X

140

130

120

110

100

90

80

70

60

50

40

30

20

10

0

Y

1

RS-D7R—/EW5 335 6 7 8

C

D

F

A

B

E

1 2 3 4

4.2 CD CORE UNIT

C

C CD CORE UNITSIDE A

IC,Q

E

HO

ME

LOA

D, E

J

LOA

D, E

J

RS-D7R—/EW5341 2 3 4

C

D

F

A

B

E

5 6 7 8

C

C CD CORE UNITSIDE B

IC,Q

LOA

D, E

J

FE

VR

EF1

1A CN652

A CN651

M2 LO

AD

ING

MO

TOR

M3 S

PIN

DLE

MO

TOR

PIC

KU

P U

NIT

(SE

RV

ICE

)(P8)

M1 C

AR

RIA

GE

MO

TOR

D CN1502

RS-D7R—/EW5 355 6 7 8

C

D

F

A

B

E

1 2 3 4

4.3 MASTER CLOCK UNIT

D

SIDE AD MASTER CLOCK UNIT

10 20 30 40 50 60 70X

80

70

60

50

40

30

20

10

0

Y

C CN301

A CN321

A CN353

RS-D7R—/EW5361 2 3 4

C

D

F

A

B

E

5 6 7 8

D

SIDE BD MASTER CLOCK UNIT

10203040506070 X

80

70

60

50

40

30

20

10

0

CLKA

CLKO

RS-D7R—/EW5 375 6 7 8

C

D

F

A

B

E

1 2 3 4

4.4 KEYBOARD UNIT

E

E KEYBOARD UNIT

E KEYBOARD UNIT

10 20 30 40 50 60 70 80X

40

30

20

10

10

20

30

40

0

10 20 30 40 50 60 70 80X0

Y

Y

VOLUME

DISPLAY

SOURCERESET

RS-D7R—/EW5381 2 3 4

C

D

F

A

B

E

8

8

5 6 7 8

E

SIDE A

SIDE B

0 90 100 110 120 130 140 150 160

0 90 100 110 120 130 140 150 160

A CN801

BAND

EJECT

OEL MODULE

RS-D7R—/EW5 395 6 7 8

C

D

F

A

B

E

1 2 3 4

4.5 OPT PCB AND SWITCH PCB

OPT PCB

B

B

F

OPT PCBB

SWITCH PCBF

SIDE BSIDE A

BLUEREDWHITE

CLOSES951

OPENS952

A CN851

A CN174

OPT OUT

RS-D7R—/EW5401 2 3 4

C

D

F

A

B

E

5 6 7 8

5. ELECTRICAL PARTS LIST

NOTE:• Parts whose parts numbers are omitted are subject to being not supplied.• The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS.....• The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V

Circuit Symbol and No. Part No.

Unit Number : CWN2000

Unit Name : Audio Control Unit

Unit Number : CWN1766

Unit Name : Master Clock Unit

Unit Number :

Unit Name : Keyboard Unit

Unit Number :

Unit Name : Switch PCB

Unit Number : CWX3369

Unit Name : CD Core Unit

Audio Control UnitConsists ofAudio Control PCBOPT PCB

ABUnit Number : CWN2000Unit Name : Audio Control Unit

MISCELLANEOUS

IC 101 (A,38,128) IC HA12187FPS1IC 102 (A,29,121) IC TA2050SIC 103 (A,42,118) IC TC7S04FUIC 121 (A,45,96) IC BA3131FSIC 122 (B,56,97) IC NJM4580M

IC 171 (A,39,134) IC TC7WH04FUIC 172 (A,44,137) IC TC7SET08FUS1IC 173 (A,48,137) IC NJM78L05UAIC 201 (A,44,82) IC PCM1800S1IC 221 (A,72,41) IC LC89055WHS-RA8

IC 251 (A,59,75) IC TC74HCT157AFIC 261 (A,79,78) IC SM5849BFIC 262 (A,83,62) IC TC7WH34FU

IC 263 (A,82,56) IC TC7SH08FUS1IC 264 (A,57,68) IC TC7SH02FUS1

IC 281 (A,71,62) IC PD0236BMIC 301 (A,60,85) IC TC9271FSIC 302 (A,52,71) IC TC7SET04FUS1IC 322 (A,34,71) IC TC7S04FUIC 401 (A,65,129) IC S-812C50AUA-C3E

IC 501 (A,75,98) IC PM4009A1IC 601 (A,118,95) IC PE5208A1IC 602 (A,102,83) IC PDH098AIC 851 (A,48,11) IC BA6288FSIC 941 (B,140,116) IC TPD1018F

IC 961 (A,110,112) IC S-80834CNUA-B8TQ 101 (A,8,114) Transistor 2SA1037KQ 102 (A,8,111) Transistor DTC124EUAQ 103 (B,9,115) Transistor 2SC4081Q 121 (B,32,95) Transistor IMD2A

Q 151 (B,64,129) Transistor 2SD1757KQ 152 (B,56,129) Transistor 2SD1757KQ 153 (B,57,120) Transistor IMH3AQ 154 (A,57,119) Transistor DTA114EUQ 155 (B,91,142) Transistor 2SC4081

Q 156 (B,78,142) Transistor DTA124EUAQ 171 (A,40,142) Transistor 2SC2412KQ 172 (B,39,132) Transistor 2SC4453Q 173 (A,46,129) Transistor 2SB1238Q 174 (B,42,124) Transistor DTC114EU

Q 261 (A,69,21) Transistor 2SD1767Q 301 (B,58,90) Transistor DTC114EUQ 401 (B,107,142) Transistor 2SC4081Q 402 (B,69,143) Transistor 2SC2412KQ 501 (A,68,114) Transistor DTA123EU

Q 601 (B,126,101) Transistor DTA114EUQ 801 (A,153,12) Transistor 2SD1760F5Q 802 (B,149,13) Transistor IMD2AQ 803 (A,140,29) Transistor 2SD2396Q 804 (A,103,12) Transistor 2SB1238

Q 805 (A,96,13) Transistor DTC124EUAQ 806 (A,103,17) Transistor 2SD1859Q 807 (B,96,18) Transistor IMD2AQ 808 (B,129,35) Transistor IMD2A


RS-D7R—/EW5 415 6 7 8

C

D

F

A

B

E

1 2 3 4

Q 851 (A,65,9) Transistor 2SD1760F5

Q 852 (B,63,11) Transistor DTA114EUQ 853 (B,73,14) Transistor DTC124EUAQ 911 (A,141,87) Transistor 2SD1760F5Q 912 (B,143,91) Transistor IMD2AQ 921 (A,140,40) Transistor 2SD2396

Q 922 (B,131,53) Transistor DTC114EUQ 923 (A,135,49) Transistor 2SB1243Q 931 (B,126,113) Transistor IMX1Q 932 (B,126,110) Transistor DTC114EUQ 951 (B,125,117) Transistor 2SA1576A

Q 962 (B,114,116) Transistor 2SC4081Q 971 (A,140,63) Transistor 2SD2396Q 991 (B,126,74) Transistor IMD2AQ 998 (A,140,74) Transistor 2SD2396D 101 (A,42,121) Diode DAN202U

D 102 (B,42,120) Diode 1SS355D 171 (B,31,143) Diode 1SS352D 221 (B,80,51) Diode Network DA204UD 222 (B,76,51) Diode Network DA204UD 261 (A,63,23) Diode HZS4LL(A)

D 262 (B,80,71) Diode Network DA204UD 263 (B,80,67) Diode Network DA204UD 264 (B,72,80) Diode Network DA204UD 265 (B,72,76) Diode Network DA204UD 281 (B,74,58) Diode Network DA204U

D 282 (B,74,61) Diode Network DA204UD 401 (A,63,121) Diode ERA15-02VHD 402 (A,66,122) Diode HZS16(2)D 801 (B,120,35) Diode Network DA204UD 802 (B,120,26) Diode Network DA204U

D 803 (B,120,29) Diode Network DA204UD 804 (B,120,23) Diode Network DA204UD 805 (B,155,12) Diode MA3056(M)D 806 (A,134,29) Diode HZS9L(C2)D 807 (B,120,32) Diode Network DA204U

D 808 (A,116,19) Diode Network DA204UD 810 (B,115,24) Diode MA3062(M)D 811 (A,103,20) Diode HZS9L(C2)D 812 (A,93,7) LED NECWB205-5780D 851 (A,57,14) Diode HZS7L(C3)

D 852 (A,23,11) Diode 1SS133D 853 (A,26,11) Diode 1SS133D 901 (A,148,130) Diode ERA15-02VHD 911 (A,148,95) Diode ERA15-02VHD 912 (A,134,87) Diode HZS6L(B1)

D 921 (A,134,43) Diode HZS9L(B3)D 922 (B,125,55) Diode DAN202UD 931 (A,140,104) Diode HZS7L(A1)D 932 (A,143,104) Diode HZS7L(C3)D 933 (A,136,104) Diode ERA15-02VH

D 943 (A,149,104) Diode ERA15-02VHD 944 (A,153,104) Diode ERA15-02VHD 951 (B,126,120) Diode DAN202UD 961 (B,114,113) Diode 1SS355D 972 (A,131,61) Diode HZS6L(B1)

D 991 (A,133,76) Diode HZS9L(B1)L 101 (A,38,123) Inductor LCTC3R3K2125L 171 (A,35,144) Inductor LCTC2R7K2125L 172 (A,32,144) Inductor LCYC1R0K2125

Circuit Symbol and No. Part No.L 173 (B,42,139) Inductor LCYC100K2125

L 174 (B,36,132) Inductor CTF1407L 201 (A,52,83) Inductor CTF1305L 202 (A,52,85) Inductor CTF1305L 221 (A,83,19) Inductor LCTAW1R0J3225L 222 (A,83,23) Inductor LCTAW1R0J3225

L 251 (A,67,71) Inductor CTF1305L 261 (A,60,38) Inductor LCTAW1R0J3225L 262 (B,79,64) Inductor CTF1305L 263 (B,76,67) Inductor CTF1305L 264 (A,85,56) Inductor CTF1305

L 265 (A,57,65) Inductor CTF1305L 281 (B,61,63) Inductor LCYC1R0K2125L 301 (A,58,92) Inductor LCTAW1R0J3225L 302 (B,56,64) Inductor LCYC100K2125L 322 (A,34,67) Inductor LCYC100K2125

L 401 (A,70,131) Inductor LAU2R2KL 402 (A,116,130) Ferri-Inductor LAU4R7KL 404 (A,98,125) Chip Coil LCTAW1R0J4532L 430 (B,70,119) Inductor CTF1295L 501 (A,65,101) Inductor LCTAW100J3225

L 503 (A,65,96) Inductor LCTAW101J3225L 504 (A,72,114) Inductor CTF1305L 601 (A,134,98) Chip Coil LCTAW100J2520L 602 (A,132,97) Inductor LCTAW2R2J2520L 604 (A,133,104) Inductor LCTAW2R2J2520

L 605 (A,130,104) Inductor LCTAW2R2J2520L 651 (A,124,70) Inductor LAU2R2KL 801 (A,137,11) Inductor CTF1614L 802 (A,126,28) Inductor CTF1489L 951 (A,146,104) Inductor LAU2R2K

X 221 (A,70,51) Crystal Resonator 12.288 MHz CSS1416X 501 (A,86,95) Radiator 3.648 MHz CSS1500X 601 (A,102,94) Radiator 12.5829 MHz CSS1495

>FU911 (A,134,94) Fuse 200 mA CEK1247>FU971 (A,116,59) Fuse 400 mA CEK1250

SP641 (A,77,11) Buzzer CPV1062EF901 (A,166,111) EMI Filter CCG1175ZNR451 (A,129,141) Surge Protector DSP-201M-A21F

FM/AM Tuner Unit CWE2027

RESISTORS

R 101 (A,32,129) RS1/10S101JR 102 (B,21,128) RS1/10S620JR 103 (A,32,126) RS1/10S101JR 104 (A,7,119) RS1/10S152JR 105 (A,35,124) RS1/16S103J

R 106 (A,10,111) RS1/10S562JR 107 (A,10,114) RS1/16S332JR 109 (B,21,122) RS1/16S181JR 110 (B,21,117) RS1/16S181JR 111 (B,22,111) RS1/16S223J

R 112 (B,22,118) RS1/16S223JR 113 (B,21,111) RS1/16S102JR 114 (B,22,123) RS1/16S102JR 115 (A,10,120) RD1/4PU560JR 116 (B,42,117) RS1/16S472J

R 117 (B,9,112) RS1/16S224JR 118 (A,41,123) RS1/16S681J


RS-D7R—/EW5421 2 3 4

C

D

F

A

B

E

5 6 7 8

R 119 (A,41,124) RS1/16S681JR 121 (B,37,97) RS1/16S622JR 122 (B,45,97) RS1/16S622J

R 123 (B,38,94) RS1/16S392JR 124 (B,46,94) RS1/16S392JR 125 (B,41,101) RS1/16S103JR 126 (B,46,100) RS1/16S103JR 127 (B,38,100) RS1/16S393J


R 153 (B,68,133) RS1/16S224JR 154 (B,61,130) RS1/16S224JR 155 (A,59,129) RS1/16S222JR 156 (A,56,129) RS1/16S222JR 157 (B,68,129) RS1/16S223J

R 158 (B,59,130) RS1/16S223JR 159 (B,95,143) RS1/16S224JR 160 (B,83,143) RS1/16S473JR 161 (A,65,133) RS1/16S102JR 162 (A,64,133) RS1/16S102J


R 172 (A,43,129) RD1/4PU272JR 173 (B,17,133) RS1/16S102JR 174 (A,28,143) RS1/16S102JR 175 (B,33,143) RS1/16S473JR 176 (A,40,138) RS1/16S102J

R 177 (B,48,135) RS1/16S470JR 181 (B,37,135) RN1/16SE1101DR 182 (B,35,128) RN1/16SE1001DR 183 (A,36,141) RN1/16SE3900DR 201 (A,51,77) RAB4C471J

R 202 (A,40,76) RS1/16S103JR 203 (B,51,78) RS1/16S561JR 221 (A,79,43) RN1/16SE1002DR 222 (A,79,46) RN1/16SE5101DR 223 (A,78,46) RN1/16SE7501D

R 224 (A,80,43) RN1/16SC75R0DR 225 (A,79,51) RAB4C221JR 227 (B,72,50) RS1/16S471JR 228 (A,70,48) RN1/16SE1003DR 229 (A,66,47) RS1/16S101J

R 230 (B,78,46) RS1/16S101JR 231 (B,81,36) RS1/16S101JR 232 (A,74,34) RS1/16S103JR 235 (B,93,93) RAB4C101JR 236 (A,70,34) RS1/16S103J

R 251 (A,69,86) RAB4C101JR 262 (A,80,68) RAB4C221JR 263 (A,66,24) RS1/16S271JR 265 (A,69,81) RAB4C101JR 266 (B,81,83) RS1/16S222J

R 269 (B,80,80) RS1/16S272JR 270 (B,95,68) RS1/16S152J

Circuit Symbol and No. Part No.R 271 (B,85,77) RS1/16S272JR 272 (A,86,61) RS1/16S221JR 273 (B,66,69) RS1/16S221J

R 281 (A,78,64) RAB4C101JR 282 (A,65,57) RS1/16S681JR 301 (A,62,92) RN1/16SE1000DR 302 (B,53,72) RN1/16SE1000DR 321 (B,42,70) RN1/16SE6800D

R 323 (B,29,67) RS1/16S470JR 351 (B,62,39) RS1/16S0R0JR 401 (B,61,142) RS1/16S473JR 402 (B,59,142) RS1/16S473JR 403 (A,58,133) RS1/16S681J

R 404 (A,60,133) RS1/16S681JR 405 (A,61,133) RS1/16S681JR 406 (A,67,133) RS1/16S102JR 407 (B,63,141) RS1/16S473JR 409 (A,79,123) RS1/16S681J

R 410 (A,79,133) RS1/16S103JR 411 (A,80,130) RS1/16S681JR 412 (A,84,131) RS1/16S681JR 413 (A,84,128) RS1/16S681JR 414 (B,78,130) RS1/16S473J


R 420 (B,103,144) RS1/16S222JR 421 (A,85,131) RS1/16S681JR 422 (A,86,128) RS1/16S681JR 423 (B,111,130) RS1/16S0R0JR 424 (B,78,125) RS1/16S393J

R 426 (B,65,139) RS1/16S153JR 427 (B,73,144) RS1/16S474JR 428 (A,79,119) RS1/16S681JR 429 (B,96,134) RS1/16S0R0JR 431 (B,69,123) RS1/8S151J

R 501 (A,73,92) RS1/16S102JR 502 (A,75,92) RS1/16S102JR 503 (A,76,92) RS1/16S102JR 511 (A,81,104) RS1/16S102JR 513 (A,78,106) RS1/16S225J

R 518 (A,78,92) RS1/16S681JR 601 (B,120,106) RS1/16S0R0JR 602 (A,108,108) RS1/16S473JR 604 (A,103,106) RS1/16S473JR 605 (A,103,105) RS1/16S473J

R 611 (B,88,82) RS1/16S473JR 612 (A,103,78) RS1/16S103JR 616 (A,115,113) RS1/16S473JR 617 (A,116,113) RS1/16S473JR 618 (A,118,113) RS1/16S473J

R 619 (B,116,107) RS1/16S0R0JR 621 (A,108,77) RS1/16S681JR 622 (A,92,59) RS1/16S102JR 624 (A,102,87) RS1/16S473JR 625 (A,89,60) RS1/16S102J

R 633 (B,104,95) RS1/16S102JR 641 (A,97,19) RS1/16S102J


RS-D7R—/EW5 435 6 7 8

C

D

F

A

B

E

1 2 3 4

R 651 (A,102,73) RS1/16S221JR 652 (A,102,74) RS1/16S221JR 653 (A,102,76) RS1/16S222J

R 654 (A,100,71) RS1/16S221JR 655 (A,103,68) RS1/16S222JR 656 (A,100,70) RS1/16S221JR 658 (B,109,32) RN1/16SC22R0DR 671 (A,117,63) RS1/16S473J

R 672 (B,101,71) RS1/16S473JR 673 (B,103,73) RS1/16S473JR 674 (A,103,71) RS1/16S473JR 676 (A,103,70) RS1/16S473JR 677 (B,127,77) RS1/16S222J

R 678 (B,95,66) RS1/16S222JR 679 (B,100,64) RS1/16S222JR 680 (A,114,77) RS1/16S104JR 801 (A,131,16) RS1/8S222JR 802 (A,129,16) RS1/8S222J

R 803 (A,125,16) RS1/8S222JR 804 (A,116,15) RS1/8S103JR 805 (A,112,15) RS1/8S472JR 806 (A,123,16) RS1/8S222JR 807 (A,103,7) RS1/16S152J

R 808 (A,121,16) RS1/8S222JR 809 (A,106,8) RS1/16S472JR 810 (B,91,15) RS1/16S681JR 812 (B,142,15) RS1/8S152JR 813 (B,148,9) RS1/16S1R0J

R 814 (A,134,32) RD1/4PU391JR 818 (A,100,9) RS1/16S472JR 821 (B,136,26) RS1/10S1R0JR 822 (B,145,9) RS1/16S222JR 823 (B,128,24) RS1/16S222J

R 824 (A,119,22) RS1/16S104JR 825 (A,121,20) RS1/16S473JR 851 (A,65,14) RD1/4PU271JR 852 (A,52,16) RS1/16S102JR 853 (A,49,16) RS1/16S102J

R 862 (A,30,16) RS1/16S102JR 863 (A,107,23) RS1/16S104JR 864 (A,31,16) RS1/16S102JR 865 (A,110,22) RS1/16S104JR 911 (B,144,93) RS1/16S223J

R 912 (B,150,93) RS1/10S472JR 921 (B,136,40) RS1/10S1R0JR 923 (A,134,46) RD1/4PU821JR 924 (A,128,52) RD1/4PU152JR 925 (B,136,51) RS1/16S223J



R 954 (B,114,111) RS1/16S102JR 962 (B,109,113) RS1/16S102J

Circuit Symbol and No. Part No.R 963 (B,119,118) RS1/16S473JR 964 (B,112,118) RS1/16S822JR 965 (A,122,112) RS1/16S472J

R 971 (B,138,64) RS1/16S392JR 991 (B,137,73) RS1/8S101JR 992 (B,132,73) RS1/8S101J

CAPACITORS

C 101 (B,15,128) CKSRYB104K16C 102 (B,38,127) CKSRYB104K16C 103 (A,25,111) CEJQ1R0M50C 104 (A,25,128) CEJQ1R0M50C 105 (A,25,117) CEJQ1R0M50

C 106 (A,25,123) CEJQ1R0M50C 107 (A,34,120) CEJQ100M16C 108 (B,32,122) CKSRYB473K25C 109 (A,38,113) CCSRCH101J50C 110 (A,42,114) CCSRCH101J50

C 111 (B,38,114) CKSRYB104K16C 121 (A,40,105) CEVWNP220M10C 122 (A,47,105) CEVWNP220M10C 123 (A,59,105) CEVW4R7M50C 124 (A,53,105) CEVW4R7M50

C 125 (B,38,102) CCSRCH470J50C 126 (B,43,102) CCSRCH470J50C 127 (B,36,94) CCSRCH221J50C 128 (B,44,94) CCSRCH221J50C 129 (B,45,91) CKSRYB223K25

C 130 (A,36,93) CEVW101M10C 131 (A,60,97) CEVW220M10C 132 (A,53,97) CEVW101M10C 133 (B,55,101) CKSRYB104K16C 134 (B,44,90) CKSRYB104K16

C 137 (B,59,103) CCSRCH151J50C 138 (B,49,97) CCSRCH151J50C 151 (A,59,125) CEJQ1R0M50C 152 (A,54,124) CEJQ1R0M50C 153 (B,95,141) CKSRYB223K25

C 161 (B,64,133) CKSRYB153K25C 162 (B,60,133) CKSRYB153K25C 163 (B,55,133) CKSRYB104K16C 171 (B,17,143) CKSRYB104K16C 172 (B,29,143) CKSRYB104K16

C 173 (A,46,142) CASA6R8M6R3C 174 (B,45,140) CKSRYB103K50C 175 (A,52,131) CEJQ101M16C 176 (B,47,136) CCSRCH220J50C 177 (B,44,137) CKSRYB104K16

C 182 (A,37,136) CKSRYB103K50C 183 (B,37,137) CCSRCH150J50C 184 (A,38,141) CKSRYB104K16C 186 (B,33,129) CKSYB106K6R3C 187 (A,29,135) CKSYB106K6R3

C 201 (A,36,86) CEVW1R0M50C 202 (A,35,76) CEVW1R0M50C 203 (A,47,88) CSZSR100M16C 204 (B,53,85) CKSRYB104K16C 205 (A,42,88) CKSYB106K6R3

C 206 (B,44,81) CKSRYB104K16


RS-D7R—/EW5441 2 3 4

C

D

F

A

B

E

5 6 7 8

C 207 (A,35,83) CSZS4R7M16C 208 (A,35,81) CSZS4R7M16C 209 (B,48,84) CCSRCH471J50C 210 (B,48,81) CCSRCH471J50

C 212 (B,45,78) CKSRYB104K16C 213 (A,43,76) CKSRYB102K50C 214 (B,24,77) CKSRYB224K16C 216 (B,53,82) CCSRCH220J50C 221 (B,75,41) CKSRYB104K16

C 222 (A,83,16) CKSRYB473K25C 223 (A,86,19) CKSRYB473K25C 224 (A,83,25) CKSRYB473K25C 225 (A,86,22) CKSRYB473K25C 226 (A,83,31) CEVW100M10

C 227 (A,85,38) CEVW100M10C 228 (A,90,15) CEVW470M6R3C 229 (A,90,22) CEVW470M6R3C 230 (A,83,48) CFHXSP104J16C 231 (B,72,45) CKSRYB104K16

C 232 (B,68,41) CKSRYB104K16C 234 (B,72,39) CKSRYB104K16C 235 (A,81,39) CFHXSQ103J16C 236 (A,83,43) CFHXSP104J16C 237 (A,83,45) CFHXSQ103J16

C 238 (B,70,50) CCSRCH270J50C 239 (B,67,50) CCSRCH330J50C 240 (B,75,38) CKSRYB103K50C 251 (B,70,70) CKSRYB104K16C 252 (B,67,73) CKSRYB473K25

C 253 (A,68,75) 10 µF/10 V CCH1424C 255 (B,78,84) CCSRCH101J50C 261 (A,57,17) CKSRYB473K25C 262 (A,75,21) CEVW470M4C 263 (A,61,44) CEVW100M10

C 264 (A,75,24) CKSRYB473K25C 265 (B,59,41) CKSRYB473K25C 266 (B,81,73) CKSRYB104K16C 267 (B,76,72) CKSRYB104K16C 268 (B,77,81) CKSRYB104K16

C 269 (B,83,81) CKSRYB104K16C 270 (B,83,62) CKSRYB104K16C 271 (B,81,77) CKSRYB102K50C 273 (A,59,22) CEJQ100M16C 274 (A,88,69) 22 µF/6.3 V CCH1426

C 275 (B,79,61) CKSYB106K6R3C 276 (A,79,57) CKSRYB103K50C 277 (A,77,58) CKSYB106K6R3C 278 (B,57,70) CKSRYB103K50C 279 (B,61,71) CKSYB106K6R3

C 281 (B,67,65) CKSRYB104K16C 282 (B,67,62) CKSRYB473K25C 283 (A,61,62) CEVW100M10C 301 (B,63,89) CKSRYB473K25C 302 (B,54,88) CCSRCH101J50

C 303 (A,52,89) 10 µF/10 V CCH1424C 304 (B,46,71) CKSYB106K6R3C 305 (B,49,71) CKSRYB103K50C 323 (B,33,72) CKSRYB473K25C 326 (B,31,72) CCSRCH101J50

C 327 (B,29,71) CKSYB106K6R3

Circuit Symbol and No. Part No.C 328 (B,112,62) CCSRCH221J50C 330 (B,24,65) CCSRCH470J50C 401 (B,65,143) CKSRYB182K50C 403 (B,76,135) CKSRYB473K25

C 404 (A,75,131) CEJQ101M10C 405 (A,105,134) CKSRYB103K50C 406 (A,97,131) CEAT221M10C 407 (B,116,133) CKSQYB103K50C 408 (B,110,141) CKSRYB223K25

C 409 (B,101,133) CKSRYB223K25C 411 (B,79,123) CKSRYB472K50C 412 (B,72,140) CKSRYB472K50C 430 (A,94,114) CCSRCH101J50C 431 (A,74,123) CEAL101M16

C 432 (B,72,128) CKSRYB104K16C 434 (B,126,88) CCSRCH101J50C 436 (B,102,133) CCSRCH102J50C 437 (B,98,144) CCSRCH101J50C 438 (B,100,144) CCSRCH101J50

C 501 (A,69,91) CEVW220M6R3C 502 (B,70,96) CCSRCH101J50C 503 (B,85,94) CCSRCH270J50C 504 (B,83,97) CCSRCH270J50C 505 (A,78,104) CKSRYB104K25

C 506 (A,76,105) CCSRCH471J50C 507 (A,73,109) CCSRCH471J50C 508 (B,70,102) CKSRYB104K25C 509 (A,69,106) CEVW220M6R3C 511 (B,63,105) CKSRYB103K50

C 512 (A,81,106) CKSRYB104K16C 513 (B,67,117) CCSRCH471J50C 601 (B,134,104) CKSYB475K10C 602 (A,133,102) CKSRYB103K50C 603 (B,130,94) CKSRYB104K16

C 604 (B,105,92) CCSRCH270J50C 605 (B,105,96) CCSRCH270J50C 606 (B,114,96) CKSRYB105K10C 607 (B,115,96) CKSRYB103K50C 608 (B,119,87) CKSRYB103K50

C 609 (B,123,102) CCSRCH101J50C 610 (B,131,106) CKSRYB103K50C 611 (A,121,110) CKSRYB103K50C 613 (B,126,103) CCSRCH101J50C 651 (A,117,71) CEJQ101M10

C 652 (B,120,69) CKSRYB473K25C 653 (B,129,69) CKSRYB473K25C 654 (B,111,68) CCSRCH471J50C 655 (A,117,64) CCSRCH471J50C 656 (B,114,72) CCSRCH471J50

C 657 (A,117,61) CCSRCH471J50C 659 (B,111,70) CCSRCH221J50C 660 (B,111,65) CCSRCH221J50C 670 (B,112,39) CCSRCH220J50C 802 (B,140,10) CKSRYB104K16

C 803 (A,143,10) CEJQ470M10C 804 (B,155,9) CKSRYB103K50C 806 (B,131,27) CKSRYB103K50C 807 (B,115,27) CKSRYB102K50C 814 (A,134,24) CEJQ470M10

C 815 (B,130,24) CKSRYB104K16


RS-D7R—/EW5 455 6 7 8

C

D

F

A

B

E

1 2 3 4

C 816 (B,130,15) CKSQYB225K10C 820 (B,124,28) CKSQYB225K10C 821 (A,124,36) CEAT101M16C 822 (B,135,11) CCSRCH101J50

C 823 (B,133,11) CKSRYB105K10C 824 (B,110,12) CKSQYB225K10C 825 (A,114,14) CKSRYB104K16C 826 (A,93,6) CKSYB104K25C 851 (B,59,12) CKSRYB103K50

C 852 (B,57,8) CKSRYB104K16C 853 (A,55,8) CEJQ220M10C 855 (A,43,12) CKSRYB102K50C 856 (A,43,15) CCSRCH101J50C 857 (A,43,9) CCSRCH101J50

C 858 (B,69,9) CCSRCH101J50C 901 (A,162,116) 4 700 µF/16 V CCH1566C 902 (B,158,121) CKSRYB104K16C 911 (A,156,93) 1 500 µF/16 V CCH1312C 912 (B,131,87) CKSRYB472K50

C 913 (B,138,94) CKSRYB103K50C 914 (A,140,96) CEJQ470M10C 921 (A,134,37) CEAT331M10C 922 (B,129,44) CKSRYB103K50C 923 (A,127,44) CEJQ101M16

C 931 (B,132,111) CKSQYB105K16C 932 (B,157,114) CKSRYB104K16C 941 (B,140,112) CKSYB225K16C 943 (B,142,121) CKSRYB104K16C 951 (B,152,99) CKSRYB104K16

C 961 (B,110,113) CKSRYB102K50C 962 (B,119,116) CKSRYB103K50C 963 (B,120,113) CKSYB225K16C 971 (A,124,62) CEJQ101M16C 972 (B,128,63) CKSRYB472K50

C 973 (B,135,56) CKSRYB103K50C 974 (A,135,55) 47 µF/25 V CCH1538C 979 (A,135,61) CEJQ100M16C 991 (B,133,79) CKSRYB473K25C 992 (B,137,68) CKSRYB102K50

C 993 (A,133,69) 100 µF/16 V CCH1539C 994 (A,134,80) CEVW100M10

DUnit Number : CWN1766Unit Name : Master Clock Unit

MISCELLANEOUS

IC 1501 (A,22,74) IC TC7SU04FUIC 1502 (A,20,29) IC NJM431UIC 1503 (A,36,29) IC NJM431UIC 1504 (A,37,59) IC NJM431UIC 1551 (A,64,29) IC NJM431U

IC 1552 (A,49,34) IC NJM2373AFIC 1553 (A,58,77) IC NJM2373AFIC 1555 (A,58,54) IC MAX4412EXKQ 1501 (A,40,17) Transistor 2SB1189Q 1502 (A,24,18) Transistor DTC114EU

Q 1503 (A,16,36) Transistor 2SC2412KQ 1504 (A,29,38) Transistor 2SC2412K

Circuit Symbol and No. Part No.Q 1505 (A,21,37) Transistor 2SD1767Q 1506 (A,34,40) Transistor 2SD1767Q 1507 (A,14,55) Transistor 2SC4226

Q 1551 (A,60,40) Transistor 2SC2412KQ 1552 (A,61,45) Transistor 2SD1767Q 1553 (A,49,54) Transistor 2SC4226Q 1554 (A,51,40) Transistor 2SC2412KQ 1555 (A,52,45) Transistor 2SD1767

L 1501 (A,17,75) Inductor CTF1305L 1551 (A,72,63) Inductor CTF1305TC1501 (A,29,60) Trimmer CCL1048TC1551 (A,60,64) Trimmer CCL1048X 1501 (A,21,60) Radiator 16.934 4 MHz CSS1560

X 1511 (A,53,64) Radiator 11.289 6 MHz CSS1724

RESISTORS

R 1501 (A,32,15) RN1/4PC4701FR 1502 (A,32,18) RN1/4PC4701FR 1503 (A,15,20) RN1/4PC2200FR 1504 (A,30,24) RN1/4PC2200FR 1505 (A,15,28) RN1/4PC2700F



R 1516 (A,25,52) RN1/4PC2202FR 1517 (A,28,66) RN1/4PC1500FR 1518 (A,28,75) RN1/4PC1200FR 1519 (A,28,70) RN1/4PC4702FR 1521 RS1/10S0R0J





CAPACITORS

C 1501 (A,55,15) 470 µF/10 V CCH1341


RS-D7R—/EW5461 2 3 4

C

D

F

A

B

E

5 6 7 8

C 1502 (A,19,17) CKSRYB103K50C 1503 (A,20,33) CKSRYB103K50C 1504 (A,36,33) CKSRYB103K50C 1505 (A,19,45) CASAQ330M10

C 1506 (A,33,47) CASAQ330M10C 1507 (A,14,47) CKSRYB103K50C 1508 (A,16,78) CKSRYB103K50C 1509 (A,37,68) CASAQ330M10C 1510 (A,38,55) CKSRYB103K50

C 1511 (A,14,59) CCSRCH470J50C 1512 (A,14,61) CCSRCH470J50C 1514 (A,22,68) CFHXS473J16C 1516 (A,20,76) CKSRYB103K50C 1517 (A,17,72) CSZS1R0M16

C 1518 (A,18,78) CKSRYB103K50C 1525 (A,35,78) CFHXS473J16C 1551 (A,69,44) CASAQ330M10C 1552 (A,70,60) CSZS1R0M16C 1553 (A,43,76) CASAQ330M10

C 1554 (A,51,76) CASAQ330M10C 1555 (A,64,33) CKSRYB103K50C 1556 (A,49,50) CKSRYB103K50C 1557 (A,49,57) CCSRCH560J50C 1559 (A,48,59) CCSRCH560J50

C 1563 (A,67,63) CFHXS473J16C 1565 (A,66,78) CKSRYB103K50C 1566 (A,55,54) CKSRYB103K50C 1568 (A,64,24) CKSRYB103K50C 1570 (A,49,30) CKSRYB103K50

C 1571 (A,54,81) CKSRYB103K50C 1572 (A,63,77) CKSRYB103K50C 1573 (A,67,15) 470 µF/10 V CCH1341C 1574 (A,61,77) CKSRYB103K50C 1575 (A,29,55) CCSRCK2R0C50

C 1576 (A,57,59) CCSRCH5R0C50

EUnit Number :Unit Name : Keyboard Unit

MISCELLANEOUS

IC 1801 (B,44,26) IC PD6556AIC 1802 (B,41,39) IC S-80929CNNB-G8ZIC 1821 (B,87,29) IC PD8166AIC 1881 (A,12,38) IC TSOP4840SB1IC 1883 (B,83,11) IC S-818A33AUC-BGN

IC 1884 (B,63,35) IC TC7SET08FUS1IC 1885 (B,60,39) IC TC7SET08FUS1IC 1886 (B,56,9) IC TC7SET08FUS1IC 1887 (B,72,28) IC TC74VHCT541AFKIC 1888 (B,31,37) IC S-93C46BD0I-J8

Q 1881 (B,131,7) Transistor DTC143EUAQ 1882 (B,130,16) Transistor DTC124EUAQ 1883 (B,133,14) Transistor 2SA1576Q 1884 (B,139,15) Transistor 2SA1576Q 1885 (B,137,11) Transistor DTC124EUA

D 1801 (B,46,36) Diode 1SS355D 1881 (A,16,5) LED NECWB205-5780D 1882 (A,16,35) LED NECWB205-5780

Circuit Symbol and No. Part No.D 1885 (A,24,12) LED NECWB205-5780D 1886 (A,7,12) LED NECWB205-5780

D 1887 (A,127,5) LED CL-196HR-CDD 1888 (A,146,12) LED NECWB205-5780D 1889 (A,157,12) LED NECWB205-5780D 1890 (A,151,5) LED NECWB205-5780D 1891 (A,151,31) LED NECWB205-5780

D 1892 (B,108,12) Diode DAP202UD 1893 (B,108,9) Diode DAN202UD 1894 (A,7,13) LED CL-196HR-CDD 1895 (A,24,13) LED CL-196HR-CDD 1896 (A,156,13) LED CL-196HR-CD

D 1897 (A,147,13) LED CL-196HR-CDD 1898 (A,151,30) LED CL-196HR-CDD 1899 (A,151,6) LED CL-196HR-CDD 1900 (A,16,33) LED CL-196HR-CDD 1901 (A,16,6) LED CL-196HR-CD

L 1801 (B,32,11) Inductor LCTAW2R2J3225L 1802 (B,31,21) Inductor LCTAW2R2J3225L 1803 (B,31,31) Inductor LCTAW2R2J3225L 1804 (B,58,12) Inductor LCTAW2R2J3225L 1821 (B,79,33) Inductor-Array CTF1542

L 1822 (B,78,38) Inductor-Array CTF1542L 1823 (B,97,32) Inductor-Array CTF1542L 1824 (B,97,36) Inductor-Array CTF1542L 1825 (B,90,16) Inductor LCTAW2R2J3225L 1861 (B,105,16) Inductor ATH1167

L 1862 (B,125,15) Inductor LCTAW2R2J3225L 1863 (B,104,33) Inductor CTF1295L 1864 (B,150,19) Inductor CTF1305L 1881 (B,117,16) Inductor CTF1305L 1882 (B,119,16) Inductor CTF1305

L 1883 (B,121,16) Inductor CTF1305X 1801 (B,56,33) Radiator 3.77 MHz CSS1427S 1881 (A,9,7) Push Switch CSG1111S 1882 (A,23,7) Push Switch CSG1111S 1883 (A,145,7) Push Switch CSG1111

S 1884 (A,143,25) Push Switch CSG1111S 1885 (A,161,25) Push Switch CSG1111S 1886 (A,159,7) Push Switch CSG1111S 1887 (A,152,35) Push Switch CSG1111S 1888 (A,152,16) Push Switch CSG1111

S 1889 (A,41,5) Push Switch CSG1111S 1890 (A,16,25) Encoder(VOLUME) CSD1042

OEL Module MXK8203

RESISTORS



R 1815 (B,49,15) RAB4C221JR 1816 (B,43,15) RAB4C221J


RS-D7R—/EW5 475 6 7 8

C

D

F

A

B

E

1 2 3 4

R 1817 (B,37,14) RAB4C221JR 1818 (B,33,16) RAB4C221JR 1819 (B,55,17) RAB4C221J

R 1821 (B,88,40) RS1/16S222JR 1822 (B,85,40) RS1/16S472JR 1841 (B,71,35) RAB4C101JR 1842 (B,75,34) RAB4C101JR 1847 (B,71,23) RAB4C101J

R 1848 (B,75,23) RAB4C101JR 1861 (B,104,37) RS1/16S101JR 1862 (B,131,31) RS1/16S473JR 1863 (B,64,40) RS1/16S152JR 1881 (B,38,6) RS1/16S181J



R 1893 (B,113,15) RS1/8S222JR 1894 (B,115,15) RS1/8S222JR 1895 (B,26,33) RS1/16S101JR 1896 (B,118,13) RS1/16S103JR 1897 (B,97,28) RAB4C102J

R 1898 (B,97,24) RAB4C102JR 1899 (B,97,20) RAB4C102JR 1900 (B,85,17) RAB4C102JR 1901 (B,80,17) RAB4C102JR 1902 (B,82,16) RS1/16S102J

R 1903 (B,104,36) RS1/16S221JR 1904 (B,59,21) RAB4C221JR 1905 (B,73,16) RAB4C221JR 1906 (B,63,28) RAB4C221JR 1907 (B,63,32) RAB4C221J



R 1918 (B,145,11) RS1/16S221JR 1919 (B,19,5) RS1/16S221JR 1920 (B,37,37) RAB4C102JR 1921 (B,34,40) RS1/16S103JR 1922 (B,29,40) RS1/16S473J

CAPACITORS

C 1801 (B,27,11) CKSYB106K6R3C 1802 (B,23,13) CKSYB106K6R3C 1803 (B,60,37) CKSRYB104K16C 1804 (B,26,17) CCSRCH101J50C 1805 (B,24,37) CKSRYB104K16


C 1809 (B,41,37) CKSRYB105K10C 1811 (B,53,35) CCSRCH101J50C 1813 (B,37,40) CKSRYB103K50C 1821 (B,90,18) CKSRYB103K50C 1822 (B,94,16) CKSQYB225K10

C 1823 (B,90,13) CKSYB106K6R3C 1861 (B,110,17) CKSQYB225K10C 1862 (B,107,32) CKSYB105K16C 1863 (B,134,33) CKSYB105K16C 1881 (A,23,14) CKSRYB104K16

C 1882 (A,7,14) CKSRYB104K16C 1883 (A,19,6) CKSRYB104K16C 1884 (A,18,34) CKSRYB104K16C 1885 (A,147,16) CKSRYB104K16C 1886 (A,158,14) CKSRYB104K16

C 1890 (A,155,6) CKSRYB104K16C 1891 (A,154,31) CKSRYB104K16C 1892 (A,6,23) CSZSR220M10C 1893 (A,6,27) CCSRCH101J50C 1894 (B,105,13) CCSRCH101J50

C 1895 (B,83,7) CKSYB474K16C 1896 (B,77,10) CKSYB225K16C 1897 (B,73,18) CKSRYB103K50C 1898 (B,54,12) CKSRYB103K50C 1899 (B,64,38) CKSRYB103K50

C 1900 (B,62,38) CKSRYB103K50

FUnit Number :Unit Name : Switch PCB

MISCELLANEOUS

S 951 Switch(CLOSE) CSN1012S 952 Switch(OPEN) CSN1022

CUnit Number : CWX3369Unit Name : CD Core Unit

MISCELLANEOUS

IC 201 IC TA2153FNS1IC 301 IC TC9495F2S1IC 401 IC BA5811FMIC 601 IC PE5238A1IC 801 IC BA05SFP

Q 101 Transistor 2SD1664Q 102 Transistor UMD2NQ 601 Transistor DTA114EUTH601 Thermistor CCX1037X 601 Ceramic Resonator 32.00 MHz CSS1544

S 901 Spring Switch(LOAD,EJ) CSN1052S 902 Spring Switch(LOAD,EJ) CSN1052S 903 Spring Switch(LOAD,EJ) CSN1052S 904 Spring Switch(HOME) CSN1051

RESISTORS

R 101 RS1/16S222J


RS-D7R—/EW5481 2 3 4

C

D

F

A

B

E

5 6 7 8

R 102 RS1/16S220JR 103 RS1/16S220JR 104 RS1/16S220JR 105 RS1/16S220J

R 201 RS1/16S153JR 202 RS1/16S153JR 203 RS1/16S823JR 204 RS1/16S823JR 205 RS1/16S102J





R 315 RS1/16S334JR 316 RS1/16S473JR 321 RS1/16S0R0JR 401 RS1/16S103JR 403 RS1/16S154J



R 602 RS1/16S1502DR 603 RS1/16S222JR 604 RS1/16S104JR 605 RS1/16S223JR 606 RS1/16S473J

R 607 RS1/16S103JR 608 RS1/16S102JR 609 RS1/16S102JR 610 RAB4CQ102JR 611 RS1/16S473J

R 701 RAB4CQ221JR 702 RS1/16S221JR 703 RS1/16S102JR 704 RS1/16S0R0JR 707 RS1/16S221J

R 708 RS1/16S0R0J

Circuit Symbol and No. Part No.R 711 RS1/16S0R0JR 713 RS1/16S0R0JR 901 RS1/16S104JR 902 RS1/16S473J

R 903 RS1/16S273J

CAPACITORS

C 101 CEVLW470M6R3C 102 CKSRYB102K50C 103 CKSRYB104K16C 104 CKSRYB334K10C 105 CEVLW470M6R3

C 106 CKSRYB104K16C 201 CKSRYB104K16C 202 CCSRCH560J50C 204 CKSRYB334K10C 205 CKSRYB334K10

C 206 CKSRYB273K25C 207 CKSRYB273K25C 208 CKSRYB104K16C 209 CKSRYB104K16C 210 CCSRCK2R0C50

C 211 CCSRCH220J50C 212 CCSRCH220J50C 301 CKSRYB153K25C 302 CKSRYB104K16C 303 CKSRYB103K50

C 304 CKSRYB822K50C 305 CKSRYB223K25C 306 CKSRYB104K16C 307 CKSRYB103K50C 308 CKSRYB104K16

C 309 CKSRYB473K16C 310 CKSRYB473K16C 311 CKSRYB104K16C 312 CKSRYB104K16C 313 CKSRYB104K16

C 314 CCSRCH221J50C 315 CEVLW220M16C 316 CEVLW101M6R3C 317 CKSRYB104K16C 318 CKSRYB104K16

C 319 CKSRYB104K16C 320 CCSRCH330J50C 325 CCSRCH471J50C 329 CKSRYB223K25C 401 CCSRCH271J50

C 402 CCSRCH471J50C 403 CKSRYB223K25C 404 CKSRYB103K50C 405 CEVLW101M10C 601 CKSRYB103K50

C 602 CKSRYB472K50C 703 10 µF/10 V CCH1349C 801 10 µF/10 V CCH1349C 802 CEVLW101M6R3C 803 CKSRYB334K10

C 901 CKSRYB103K50C 902 CKSRYB103K50


RS-D7R—/EW5 495 6 7 8

C

D

F

A

B

E

1 2 3 4

Miscellaneous Parts List

M 1 Carriage Motor Assy CXC5819M 2 Load Motor Assy CXC5821M 3 Motor Unit CXC6003

Pickup Unit(Service)(P8) CXX1305M 10 Motor Unit CXC2489


RS-D7R—/EW5501 2 3 4

C

D

F

A

B

E

5 6 7 8

6. ADJUSTMENT6.1 MASTER CLOCK ADJUSTMENT

- Master Clock Unit frequency adjustmentNo. Measuring point Adjusting point Content of adjustment

TC1501 Frequency counter : 16 934.400 ± 20 Hz1 CLKO

- Adjustment point

TC1551 Frequency counter : 11 289.600 ± 15 Hz2 CLKA

CLKA

CN1501

CN

1551

CN1502

TC1551

TC1501

CLKO

SIDE BSIDE A

1. Remove the Master Clock Unit from the Audio Control Unit.2. Play the CD with the cable connected.3. Monitor CLKO (frequency counter and high frequency probe are required) and adjust TC1501 to match the frequency.4. Monitor CLKA (frequency counter and high frequency probe are required) and adjust TC1551 to match the frequency.

RS-D7R—/EW5 515 6 7 8

C

D

F

A

B

E

1 2 3 4

6.2 CD ADJUSTMENT

1) Precautions• This unit uses a single power supply (+5V) for the reg-

ulator. The signal reference potential, therefore, isconnected to VREF(approx. 2.1V) instead of GND.If VREF and GND are connected to each other by mis-take during adjustments, not only will it be impossi-ble to measure the potential correctly, but the servowill malfunction and a severe shock will be applied tothe pick-up. To avoid this, take special note of the fol-lowing.Do not connect the negative probe of the measuringequipment to VREF and GND together. It is especiallyimportant not to connect the channel 1 negativeprobe of the oscilloscope to VREF with the channel 2negative probe connected to GND.Since the frame of the measuring instrument is usual-ly at the same potential as the negative probe, changethe frame of the measuring instrument to floating sta-tus.If by accident VREF comes in contact with GND,immediately switch the regulator or power OFF.

• Always make sure the regulator is OFF when connect-ing and disconnecting the various filters and wiringrequired for measurements.

• Before proceeding to further adjustments and mea-surements after switching regulator ON, let the playerrun for about one minute to allow the circuits to stabi-lize.

• Since the protective systems in the unit's software arerendered inoperative in test mode, be very careful toavoid mechanical and /or electrical shocks to the sys-tem when making adjustment.

• The RFI and RFO signals are easy to oscillate becauseof a wide band. When observing them, insert a resis-tor of about 1 kΩ to the series.

• This equipment will not guarantee the load ejectionoperation when the mechanical unit is turned upsidedown. In particular, if the ejection operation is incor-rectly performed and recovery is disabled, the recov-ery is enabled by resetting a product or turning ACCoff to on.

2) Test ModeThis mode is used for adjusting the CD mechanismmodule of the device.

• Test mode starting procedureReset while pressing the DISP and ] keys together.

• Test mode cancellationSwitch ACC, back-up OFF.

• After pressing the EJECT key, do not press any otherkey until the disk is completely ejected.

• If the ] or [ key is pressed while focus search is inprogress, immediately turn the power off (otherwisethe actuator may be damaged due to adhesion of thelenses).

• Jump operation of TRs other than 100TR continuesafter releasing the key. CRG move and 100TR jumpoperations are brought into the “Tracking close” sta-tus when the key is released.

• Powering Off/On resets the jump mode to “1TR”, theRF AMP gain setting to TYP, and the automatic adjust-ment value to the initial value.

• Please use the "remote control unit of the productaccessory" after the test mode starts.

RS-D7R—/EW5521 2 3 4

C

D

F

A

B

E

5 6 7 8

*1)+12dB

TRK12 MIN12 SEC12TYP

TRK MIN SEC Switch a value

*3)

*2) Focus Close for “00” or “99” display

S. curve check settingTRK01 MIN01 SEC01

Focus Close settingTRK00 MIN00 SEC00

or TRK99 MIN99 SEC99 Switch a value

*4) CRG motor voltage = 2 [V]

*5)T.OffsetDisplay

Switch to the order of the original displayF.OffsetDisplay

*6)F.AGCGain

RF AGCGain

TRK/MIN/SEC Switch a valueT.AGCGain

*7)1TR

TRK91 MIN91 SEC91or TRK81 MIN81 SEC81

32TRTRK92 MIN92 SEC92

or TRK82 MIN82 SEC82

100TRTRK93 MIN93 SEC93


CRG MoveTRK94 MIN94 SEC94


Switch a value

*8) 1TR/32TR/100TR

*9) Only at the time of CRG move or 100TR jump

[BAND]

Power On(F. T. offset is adjusted)

TRK00 MIN00 SEC00

[SOURCE]

Source S-CD

TRK MIN SEC

[DISP]+[ ]+Reset

Test Mode In

[3]

Power On(F. T. offset is not adjusted)

TRK99 MIN99 SEC99

[2]

RF AMPGain switching*1

TRKGG MINGG SECGG

[BAND]

Power Off

TRK MIN SEC

[BAND]

Power Off

TRK MIN SEC

[BAND]

Power Off

TRK MIN SEC

[BAND]

Power Off

TRK MIN SEC

[3]

Focus Close /S. curve check *2

TRK91 MIN91 SEC91

[6]

Focus Mode switching*3

TRK0x MIN0x SEC0x

[1]

Tracking ServoClose


[[]

CRG- *4


[]]

CRG+ *4


[6]

New Test Mode

[2]

Automatic adjustment value

display switching *5

TRK?? MIN?? SEC??

[1]T.CLS and F,T AGC

and RF AGC andApplicable servomechanism

TRKxx MINxx SECxx

[6]

T.Close andApplicable servomechanism

TRKxx MINxx SECxx

[3]

RF AGC /RF AGC coefficient display

TRK?? MIN?? SEC??

[]]

CRG+

TRK8x MIN8x SEC8xor TRK9x MIN9x SEC9x

[[]

CRG-


[2]

T.Balance adjustment /T.Balance coefficient display

TRK?? MIN?? SEC??

[1]

F,T,RF AGC /F.Bias display switching*6

TRK?? MIN?? SEC??

[3]

F,T AGC,F.Biasand RF AGC

TRKxx MINxx SECxx

[6]

CRG/TR jump value *7

switching

TRKxx MINxx SECxx

[]]

CRG+/TR Jump+ *8

TRK xx MINxx SEC xx

[[]

CRG-/TR Jump+ *8

TRK xx MIN xx SEC xx

[2]

Tracking Open

TRK8x MIN8x SEC8xor TRK 9x MIN9x SEC 9x

[2]

Tracking Open


*9

F. EQ measurement settingTRK02 MIN02 SEC02

[Key]

[BAND]

[]]

[[]

[1]

[2]

[3]

[6]

-

-

Power On/Off

CRG +/TR Jump+(Direction of the external surface)

CRG -/TR Jump-(Direction of the internal surface)

T.CLS and AGC and Applicable servomechanism/

AGC,AGC display switching

RF Gain switching/Offset adjustment display/

T.Balance adjustment/T.OPN

F.CLS,S.Curve/Rough Servo and RF

Lens down/SPDL 1X/2X switching(Double-speed compatibility only)

Error rate measurement

F.Mode switching/T.CLS/CRGJump switching

Test Mode New Test Mode

Operation

Error occurrence time/cause display switching

TRK+/FF

TRK-/REV

SCAN

MODE

(ITP)

-

-

Auto/Manual switching

F.Bias

[KEY]

Contents

Display

Perform the S. curve check operation for “01” display

- Flow Chart

RS-D7R—/EW5 535 6 7 8

C

D

F

A

B

E

1 2 3 4

6.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjustedPU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, ifthe PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to performtrack search operations, or taking a long time for track searching.

• Method :

• Measuring Equipment • Oscilloscope, Two L.P.F.• Measuring Points • E, F, VREF• Disc • TCD-784• Mode • TEST MODE

• Checking Procedure1. In test mode, load the disc and switch the 5 V regulator on.2. Using the ] and [ buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-

ment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourthpress.

4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-ence is within 75° . Refer to the photographs supplied to determine the phase angle.

5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is anyimprovement. If, after trying this a number of times, the grating angle does not become less than 75° then themechanism should be judged to be at fault.

• NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveforseen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-age angle.

• HintReloading the disc changes the clamp position and may decrease the "wobble".

100 kΩ

390 pF

100 kΩ

390 pF

E

VREF

F

VREF

Xch Ych

Oscilloscope

L.P.F.

L.P.F.

CD CORE UNIT

EF

VREF

RS-D7R—/EW5541 2 3 4

C

D

F

A

B

E

5 6 7 8

Grating waveform Ech → Xch 20 mV/div, ACFch → Ych 20 mV/div, AC

45°

0°

75°

60°

30°

90°

RS-D7R—/EW5 555 6 7 8

C

D

F

A

B

E

1 2 3 4

6.4 ERROR MODE

- CD Section Error No. Display

If the CD player cannot operate or if it stops when an error occurred in operation, it enters the error mode and dis-

plays the cause of the error in numerals. Accordingly, an object of this display is to assist in analysis and repair.

(1) Display example

Err XX

(2) Error codes

Error code Type Description Details and cause10 Mechanical unit Carriage Home NG Carriage cannot move to and from the inside circumference.

→ Defective Home SW, Carriage move error.11 Electricity Focus Search NG Focus is disabled.

→ At the rear of disc. Disc damage, dirt and vibration are intense.

12 Electricity Spindle Lock NG Spindle Lock is not performed and no subcode can be read.→ Defective spindle. Disc damage, dirt and vibration are intense.

14 Electricity Mirror NG CD-R to which data is not written.(At the rear of disc on rare occasions)

17 Electricity Setup NG AGC protection does not work.Focus immediately slips off.→ Disc damage, dirt and vibration are intense.

19 Electricity Setup NG The tracking balance deviation is 50% or higher or the tracking error level is low.→ The pickup or tracking error circuit is abnormal.

30 Electricity Search Timeout Could not reach the target address.→ Carriage/tracking error, disc damage.

A0 System Power Supply NG Higher or lower than the specified voltage, or no power is output.→ Defective SW transistor, power supply abnormality, load terminal NG.

* Setup indicates a series of operations until sound is issued after focus has been performed.

RS-D7R—/EW5561 2 3 4

C

D

F

A

B

E

5 6 7 8

- CD Section Test Mode (Aging Operation and Setup Analysis)

Play is performed in the CD normal mode. However, after setup, in the protection operation, such as FOK (focus),

LOCK (spindle), subcodes. sound skip and mechanical-unit errors, the error occurrence and a timeout, the occur-

rence cause and occurrence time are displayed. During setup, the operation status (internal RAM; CPOINT) of the

CD software is displayed.

(1) Entering the new test mode

See the test mode flowchart.

(2) Correspondence of keys between the test mode and new test mode

Key Test mode New test mode

Regulator OFF Regulator ON In-play Error or protection occurrence

BAND Regulator ON Regulator OFF Error occurrence time or error cause switching

] FWD-KICK TRACK > [ REV-KICK < TRACK 1 TRACKING CLOSE SCAN 2 TRACKING OPEN MODE 3 FOCUS CLOSE (ITP) 6 To new test mode FOCUS MODE SWITCHING AUTO/MANUAL

The conventional operation is performed for EJECT or CD ON/OFF.

(3) Error cause (error No.) codes

Error code Type Mode Description Details and cause

40 Electricity PLAY FOK=L Focus slips off.

100mS → Damage, dirt, vibration and faulty

servomechanism.

41 Electricity PLAY LOCK=L Spindle Lock slips off.


servomechanism.

42 Electricity PLAY Subcode NG No subcode can be read.


servomechanism.

43 Electricity PLAY Sound skip Last address memory operation.

occurrence → Damage, dirt, vibration and faulty

servomechanism.

RS-D7R—/EW5 575 6 7 8

C

D

F

A

B

E

1 2 3 4

(4) Operation status display during setup

Status No. Description Protection operation

00 CD + 5 V ON is being processed. None

01 SERVO LSI is being initialized (1/3). None

02 CRAM of servo LSI is being initialized. None

03 SERVO LSI is being initialized (2/3). None

04 Offset is being adjusted (1/3). None



07 FZD is being adjusted. None

08 Servo LSI is being initialized (3/3). None

10,11 Carriage Home processing start. None

12 Carriage is moving toward the inside Timeout for ten seconds, defective Home SW.

circumference.

13 Carriage is moving toward the outside Timeout for ten seconds, defective Home SW.

circumference.

14 Carriage outer kicking. None

15 Carriage is being sent to the outside None

circumference. (for one second)

20 Servo Close processing start. None

21 Being processed before Focus Search None

start.

22 Spindle rotation, Focus Search start. None

23 Focus Close (FOON = Low) wait. Focus Search timeout.

24 Waiting after Focus Close. None


start, at setup protection.


start, at fast recovery.

27 RF detection. (RFOK = Hi confirmation) Focus slips off, no RF is output.

28 Spindle OLV rough servocontrol. Focus slips off.

29 Setting before T balance adjustment Focus slips off.

processing start.

30 T balance adjustment (1/2). Focus slips off.

31 T balance adjustment (2/2). Focus slips off.

32 Spindle CLV stationary servocontrol. Focus slips off.

33 Tracking Close processing (1/2). Focus slips off.

34 Tracking Close processing (2/2). Focus slips off.

35 Setting before Focus/Tracking AGC Focus slips off.

start.

36 Focus AGC start processing. Focus slips off.

37 Focus AGC processing (1/2). Focus slips off.

38 Focus AGC processing (2/2). Focus slips off.

39 Setting before Tracking AGC start. Focus slips off.

RS-D7R—/EW5581 2 3 4

C

D

F

A

B

E

5 6 7 8

6.5 SYSTEM MICROCOMPUTER TEST PROGRAM

(5) Example of display on display unit

• During setup

• In operation (PLAY and SEARCH), this mode is almost the same as the normal mode.

• At protection/error occurrence

(a) Error display

Display is switched using the BAND key.

(b) Occurrence TNo. display, occurrence absolute time display

TNo.

11Min

11Sec

11

Err–xx

TNo.

10Min

40Sec

05

Status No. Description Protection operation

40 Tracking AGC start processing. Focus slips off.

41 Tracking AGC processing. Focus slips off.

42 Focus/Tracking AGC processing. Focus slips off, AGC coefficient NG.

43 FE bias adjustment start processing. Focus slips off.

44 FE bias adjustment. Focus slips off.

45 RFAGC adjustment start. Focus slips off.

46 RFRP level read processing. Focus slips off, low RFRP level.

47 Setting before Lock confirmation. Focus slips off.

48 Lock is being checked. Focus slips off, Spindle Lock is not performed.

49 Setting before subcode confirmation. Focus slips off.

50 Subcode confirmation. Focus slips off, no subcode can be read.

In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby modecancelled), shift the TESTIN (Pin 5) terminal to H.The clock signal is output from the PCL terminal (Pin 62).The frequency of the clock signal is 786.432 kHz that is one 16th of the fundamental frequency.The clock signal should be 786.432 kHz ± 32 Hz.If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

- PCL Output

RS-D7R—/EW5 595 6 7 8

C

D

F

A

B

E

1 2 3 4

7. GENERAL INFORMATION7.1 DIAGNOSIS7.1.1 DISASSEMBLY

- Removing the CD Mechanism Module (Fig.1)

1

Fig.1

- Removing the Case (not shown)

Grille Assy

- Removing the Grille Assy (Fig.2)

1. Remove the Case.

CD Mechanism Module

1

1

1

1

Fig.2

Remove the four screws.

1

1

1

1

1

Remove the four screws.

Disconnect the connector and then remove theCD Mechanism Module.

Disconnect the connector and then remove theGrille Assy.

RS-D7R—/EW5601 2 3 4

C

D

F

A

B

E

5 6 7 8

Fig.3Audio Control Unit

- Removing the Audio Control Unit (Fig.3)

Remove the four screws.1 1

1

2

2

3

3

Straighten the tabs at five locationsindicated.

2

3

11

2

2

2

- Removing the Master Clock Unit (Fig.4)

1. Remove the solder of three tabs indicated by arrows A and then detach the Shield.2. Remove the solder of five tabs indicated by arrows B, disconnect each of the connectors, and then detach the Master Clock Unit.

(Note) Do not bend the tab indicated by C when assembling. Also, do not solder it.

Fig.5

BC B

BBB

A

A

A

Master Clock Unit

Shield

Remove the two screws.

Remove the seal and then remove theAudio Control Unit.

*) While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.

RS-D7R—/EW5 615 6 7 8

C

D

F

A

B

E

1 2 3 4

Top Frame

Clamper Arm

Assy

Guide Arm

Assy

Main Frame

DiskDamper

Damper

The numeral enclosed by a circle in the drawing indicatesthe order of removal.

- How to hold the mechanism unit1. Hold the top frame and main frame.2. Do not hold the front of the top frame tightly because its strength is low.

- How to remove the top frame and main frame1. Remove the screws (4) and screws (2) of the top frame in the clamped state and remove the top frame.2. After having removed the screws of the dampers (2) on the right and the dampers, remove the main frame.3. Remount the product connector with the frame removed and eject a disk.

- How to remove the clamper arm assy and

guide arm assy1. Remove a total of three right, left and rear screws and remove the clamper assy.2. Remove the left spring and remove the torsion spring hook of the right fulcrum unit.3. Remove the E ring of the left fulcrum and remove the guide arm assy.

RS-D7R—/EW5621 2 3 4

C

D

F

A

B

E

5 6 7 8

Loading Motor Assy

Loading Arm Assy Spindle

Motor

Gear Cover

Holder

Leaf Spring

Holder

Grease Application

(GEM1029)

- How to remove the loading arm assy and

spindle motor1. Remove the E ring of the left fulcrum and remove the spring and loading arm assy.2. Remove the connector of the spindle motor and remove the mounting screws (3).

- How to remove the loading motor assy1. Remove the gear cover screw and remove the gear cover.2. Remove the holder which was tightened together with the gear cover.(Note): At assembly, tighten the holder together with the gear cover by approaching the holder to the arrow view direction and touching the tip of the motor shaft. At that time, if the holder is tightened with screws while it is being pressed, the motor load is increased and causes an error (NG). While the holder is approached, separate the hand from the holder and the holder is tightened with the screws.3. Remove the solder of the motor lead wire.4. Remove the leaf spring screw and remove the holder and leaf spring.5. Put the mechanical unit face downward, remove the mounting screws of the loading motor assy and remove the loading motor assy.

RS-D7R—/EW5 635 6 7 8

C

D

F

A

B

E

1 2 3 4

Core Unit

Carriage Motor Assy

Jumper PinPickup

Grease Cover

Core Unit

Main Shaft

Main Shaft Holder

Grease Application

(GEM1030)

Grease Application

(GEM1030)

- How to remove the carriage motor assy1. Remove the solder of the carriage motor lead wire.2. Remove the grease cover screw and remove the grease cover.3. After having removed the lead wire processing of the motor, remove the mounting screw of the carriage motor assy.

- How to remove the pickup1. Mount the jumper pin and remove the pickup connector.2. After having the processing of flexible wires, remove the mounting screw of the main shaft holder and remove the pickup together with the main shaft holder and the main shaft.

RS-D7R—/EW5641 2 3 4

C

D

F

A

B

E

5 6 7 8

7.1.2 CONNECTOR FUNCTION DESCRIPTION

1. ILL2. GND3. MUTE4. NC5. B.UP6. ACC7. B.REM8. NC

ANTENNA JACK

1. BUS+ 2. IPGND 3. IPGND 4. NC 5. BUS- 6. IPGND 7. BUS L OUTPUT 8. ASENB 9. BUS R OUTPUT10. IPGND11. IPGND

11 10 9 8

7 6 5

4 3 2 1

IP-BUS OUTPUT

IP-BUS INPUT

111098

765

4321

1. BUS+ 2. GND 3. GND 4. NC 5. BUS- 6. GND 7. BUS L+ INPUT 8. ASENB 9. BUS R+ INPUT10. BUS R- INPUT11. BUS L- INPUT

1. GND 2. GND 3. NC 4. OPTOUT

OPTICAL OUTPUT

43

21

43

21

1. GND 2. GND 3. NC 4. OPTOUT

OPTICAL INPUT

8 7 6 54 3 2 1

RS-D7R—/EW5 655 6 7 8

C

D

F

A

B

E

1 2 3 4

7.2 IC

TC7SH02FUS1

IN B

IN A

GND OUT Y

VCC1

2

3

5

4

TC7SET04FUS1

- Pin Functions (PCM1800S1)Pin No. Pin Name I/O Function and Operation

1 VINL I Analog input, Lch2 VREF1 Reference 1 decoupling capacitor3 REFCOM Reference decoupling common4 VREF2 Reference 2 decoupling capacitor5 VINR I Analog input, Rch6 RSTB I Reset input7 BYPAS I LCF bypass control

8, 9 FMT0, 1 I Audio data format 0, 110, 11 MODE0, 1 I Master/slave mode select 0, 1

12 FSYNC I/O Frame synchronous input/output13 LRCK I/O Sampling clock input/output14 BCK I/O Bit clock input/output15 DOUT O Audio data output16 SYSCK I System clock input 256fs, 384fs, 512fs17 DGND Digital GND18 VDD Digital power supply19 CINNR Anti-aliasing filter capacitor (-)Rch20 CINPR Anti-aliasing filter capacitor (+)Rch21 CINNL Anti-aliasing filter capacitor (-)Lch22 CINPL Anti-aliasing filter capacitor (+)Lch23 VCC Analog power supply24 AGND Analog GND

PCM1800S1

11213 24

1

2

3 4

5

GND

VCC

IN A

NC

OUT Y

PCM1800S1TC7SH02FUS1TC7SET04FUS1LC89055WHS-RA8TC74HCT157AFPDH098ASM5849BFTC9271FSHA12187FPS1PE5208A1

PD0236BMPM4009A1NJM2373AFNJM431UMAX4412EXKTC74VHCT541AFKPD8166AS-80929CNNB-G8ZPD6556AS-93C46BDOI-J8

TA2153FNS1TC9495F2S1PE5238A1

RS-D7R—/EW5661 2 3 4

C

D

F

A

B

E

5 6 7 8

- Pin Functions (LC89055WHS-RA8)Pin No. Pin Name I/O Function and Operation

1 DISEL I Select input pin for data input pin(DIN0,DIN1)2 DOUT O Output pin for serial audio data3 DIN0 I Digital data input pin4 DIN1 I Digital data input pin5 DIN2 I Digital data input pin6 DGND GND for digital circuit7 DVDD Digital VDD pin(5V)8 R I VCO gain control input pin9 VIN I Input pin for VCO free run frequency setting

10 LPF O PLL loop filter setting pin11 AVDD Analog power supply12 AGND Analog GND13 CKOUT O Clock output pin14 BCK O 64fs clock output pin15 LRCK O fs clock output pin16 DATAO O Data output pin17 XSTATE O Output pin for source clock switch monitor18 DGND Digital GND19 DVDD Digital power supply20 XMCK O Crystal oscillation clock output pin21 XOUT O Crystal oscillator connection output pin22 XIN I Crystal oscillator connection input pin23 EMPHA O Output pin for emphasis information of channel status24 AUDIO O Output pin for bit 1 of channel status (non-PCM data detection bit)25 CSFLAG O Output pin for updating flag of the leading 40 bits of channel status26 F0/P0/C0 O Output pin for calculated signal of input fs/Pc data type/input word

information27 F1/P1/C1 O Output pin for calculated signal of input fs/Pc data type/input word

information28 F2/P2/C2 O Output pin for calculated signal of input fs/Pc data type/input word

information29 VF/P3/C3 O Output pin for validity flag/Pc data type/input word information30 DVDD Digital power supply31 DGND Digital GND32 AUTO O Output pin for non-PCM burst data transmission detection signal(Pa,Pb detection)33 BPSYNC O Output pin for non-PCM burst preample Pa, Pb, Pc, Pd sync signal34 ERROR O Output pin for PLL lock error, data error flag35 DO O Output pin for microcomputer IF read data36 DI I Output pin for microcomputer IF write data37 CE I Microcomputer IF chip enable pin38 CL I Microcomputer IF clock input pin39 XSEL I Select input pin for XIN crystal oscillator frequency40 MODE0 I Mode setting input pin41 MODE1 I Mode setting input pin42 DGND Digital GND43 DVDD Digital power supply44 DOSEL0 I Output data format select input pin45 DOSEL1 I Output data format select input pin46 CKSEL0 I Output clock select input pin47 CKSEL1 I Output clock select input pin48 XMODE I System reset input pin

RS-D7R—/EW5 675 6 7 8

C

D

F

A

B

E

1 2 3 4

36

37

48

1 12

13

24

25

LC89055WHS-RA8 TC74HCT157AF

VCC

st

4A

4B

4Y

3A

3Y

SELECT

1A

1B

1Y

2A

2B

GND

3B2Y

1

2

3

4

5

6

7

8 9

10

11

12

13

14

15

16

st

SE

LEC

TA

BH

XX

XL

LL

LX

LL

LH

XH

LH

XL

LL

HX

HH

OU

TP

UT

INP

UT

X: D

on't

Car

e

CS

SK

DI

DO

VCC

NC

TEST

GND

1

2

3

4

8

7

6

5

MemoryAray

AddressDecoder

Mode DecodeLogic

Data Resistor Output Buffer

Clock PulseCounter

Voltage Detector

Clock Oscillater

PDH098A

RS-D7R—/EW5681 2 3 4

C

D

F

A

B

E

5 6 7 8

SM5849BF

1

202140

41

60

61 80

- Pin Functions (SM5849BF)Pin No. Pin Name I/O Function and Operation

1 VDD Power supply pin2 DI I Digital input pin3 BCKI I Bit clock input pin4 LRCI I Word clock input pin5 VSS GND pin6 ICLK I System clock input pin7 ICKSL I System clock select pin

8, 9 IFM1, 2 I Input format select pin 1, 210, 11 IWL1, 2 I Input word length select pin 1, 212-19 NC Not used

20 VSS GND pin21 VDD Power supply pin22 DMUTE I Direct mute pin23 MCOM I Microcomputer control select pin24 MDT/FSI1 I Microcomputer I/F data input/de-emphasis filter fs select pin 125 MCK/FSI2 I Microcomputer I/F clock input pin/de-emphasis filter fs select pin 226 MLEN/DEEM I Microcomputer I/F latch enable input pin/de-emphasis function select pin

27-39 NC Not used40 VSS GND pin41 VDD Power supply pin

42, 43 OWL2, 1 I Output data bit length select pin 2, 144 IISN I IIS output select pin45 STATE O State output pin46 TST2N I IC test mode setting pin 247 DITHN I Output dither control pin48 RSTN I Reset input pin49 THRUN I Through mode setting pin50 SLAVE I Slave mode setting pin

51-59 NC Not used60 VSS GND pin61 VDD Power supply pin62 OCKSL I Output system clock select input pin63 OCLK I Output system clock input pin64 VSS GND pin65 LRCO O Word clock output pin66 BCKO O Bit clock output pin67 DOUT O Data output pin

68-79 NC Not used80 VSS GND pin

RS-D7R—/EW5 695 6 7 8

C

D

F

A

B

E

1 2 3 4

1 32

S1 R S2 GND

BUS-BUS+VCCSTB

4

5678

BIAS

DRIVEROUTPUT

+

-

-

+

COMRECEIVEROUTPUT

HA12187FPS1

- Pin Functions (TC9271FS)Pin No. Pin Name I/O Function and Operation

1 BLOCK O Block start position output pin2 UBDA I User bit data input pin3 LRS I LRCK polarity select pin4 LRCK I LR clock input pin5 NC Not used6 BCK I Bit clock input pin7 DATA I 2ch:data input pin /4ch:data input pin 18 VLDY I 2ch:correction flag input pin /4ch:data input pin 29 EMPH I Emphasis flag setting pin

10 COPY I P:copy flag setting pin /S:"H" fixed11, 12 FS1, 2 I Sampling frequency setting pin 1, 2

13 CKS I Clock subharmonic number select pin14 XI I Clock input pin15 VSS GND pin

16, 17 DO1, 2 O Digital data output pin 1, 218, 19 M1, 2 I Channel mode setting pin 1, 220, 21 IS1, 2 I Data input mode setting pin 1, 2

22 CTG1 I P:category code setting pin 1/S:data input pin23 CTG2 I P:category code setting pin 2/S:clock input pin24 CTG3 I P:category code setting pin 3/S:latch pulse input25 FR32 O FR32 output pin26 NC Not used27 LBIT I P:LBIT input pin/S:32/192 bit switch pin28 CKA1 I P:clock precision setting pin 1/S:"H" fixed29 CKA2 I P:clock precision setting pin 2/S:do not output30 VDD Power supply voltage pin

TC9271FS

11516 30

RS-D7R—/EW5701 2 3 4

C

D

F

A

B

E

5 6 7 8

- Pin Functions (PE5208A1)Pin No. Pin Name I/O Function and Operation

1 SWVDD O GRILL: chip enable output2 DSENS I Grille detach sense input3 SUBOK I Sub code receivability verification4 TELIN I TELL MUTE input5 TESTIN I Test program mode input6 AUTOANT O Antenna power output7 DERR I DIR error detection8 DIRCL O DIR clock output pin9 DIRDI O DIR write data output pin

10 DIRDO I DIR read data input pin11 RESET I Reset input12 XT2 Time clock connection pin13 XT1 I Time clock connection pin14 VSS GND pin15 X2 Main oscillator connection pin16 X1 I Main oscillator connection pin17 REGOFF Regulator operation signal18 REGC Connection for capacity stabilizing regulator output19 VDD Power supply pin (VDD)20 DIRCE O DIR chip enable output pin21 SYSPWR O SYSTEM: system power control22 FLPPWR O FLAP: flap power control23 FLPILM O FLAP: illumination in flap control24 ILMPWR O Illumination power control25 OELPW O OEL power supply output26 AUDIO I Non-PCM data detection input27 IPPW O IPBUS: driver power supply control28 ASENBO O IPBUS: slave Acc sense output29 FM/AM O TUNER: decoder power supply control output30 MUTE O SYSTEM: integrated MUTE output31 ROMDATA O ROM correction data output32 ROMCK O ROM correction clock output33 ROMCS O ROM correction chip select output34 ANTFIX O TUNER: diversity output35 LOCL O TUN: local L output36 LOCH O TUN: local H output37 TUNPCE2 O TUN:EEPROM chip enable output38 SD I TUN:SD input39 ST I TUN:stereo input40 VSS GND pin (GND)41 VDD Power supply pin (VDD)42 FLPCLS O FLAP: close output43 FLPOPN O FLAP: open output44 FOPNSW I FLAP: open sense SW input45 FCLSSW I FLAP: close sense SW input46 DRST O Digital system IC reset output47 DMUTE O Digital system mute48 VCK O E.VOL: clock output49 VDT O E.VOL: data output50 VST O E.VOL: strobe output51 ASEL O Analog selector switch output52 DSEL O Digital selector switch output53 DIRSEL O DIR input selector switch output54 DRST2 O RDS: decoder reset output55 RDSLK I RDS:LK input56 RDT I RDS: data input57 CURRQ O RDS:TUNER voltage FIX output58 NL2DT I RDS: noise level 2

RS-D7R—/EW5 715 6 7 8

C

D

F

A

B

E

1 2 3 4

Pin No. Pin Name I/O Function and Operation59 TMUTE O RDS:TUNER mute output60 SDBW I RDS:SD input in case of NF61 RECIVE O RDS:reception output62 PCL Output for adjusting clock

63,64 ROT0, 1 I Rotary encoder input 0, 165 BSCK I PBUS:clock input pin66 BSI I PBUS:data input67 BSO O PBUS:data output68 BRXEN I/O PBUS:communication enable69 BRST O PBUS:reset output70 BSRQ I PBUS:communication demand input71 DALMON O Electric current switch in case of standby72 NC Not used73 TEST Pin for testing IC (GND)74 SL TUNER:signal level input75 NC Not used76 O Do not output DIT77 NC Not used78 BATT I Backup voltage input79 NL1 RDS:noise level input 1(A/D)80 MODEL I Model information input81 ADPW O A/D converter SW82 AVDD A/D converter positive power suppply (VDD)83 AVREF A/D converter reference voltage (VDD)84 AVSS A/D converter GND pin (GND)85 RX IP-BUS:data input86 TX IP-BUS:data output87 NMI I Do not use this (GND)88 LDET I PLL lock detection input89 RCK I RDS:RDS clock input90 RDS57K I RDS:57kHz pulse count input91 ISENS I Illumination sense input92 ASENS I Acc sense input93 BSENS I B.up sense input94 TUNPDI I TUN: data input95 RXD I GRILLE: data input96 TXD O GRILLE: data output97 TUNPCK O TUN: clock output98 TUNPDO O TUN: data output99 TUNPCE O TUN: chip enable output

100 PEE O PEE sound output

PE5208A1

30

31

50

51 80

81

100

1

ditinh

I

I

O

IO

RS-D7R—/EW5721 2 3 4

C

D

F

A

B

E

5 6 7 8

Data delay

Timing generation

Data input

Data distinction part

Distinction data delay part

Operation part

Confficnt storage ROM

Data output

VDD

LRCKI

DATAI

BCKI

SEL

XRST

BCSEL

DASEL

LRSEL

LRCKO

BCKO

DATAO

GND

1

2

3

4

5

6

7

8

9

18

17

16

15

14

13

12

11

10

BCSEL

DASEL

NC

LRSEL

LRCKO

NC

BCKO

DATAO

GND VDD

LRCKI

NC

NC

DATAI

BCKI

NC

SEL

XRST

PD0236BM

- Pin Arrangement Chart

- Block Diagram Chart

RS-D7R—/EW5 735 6 7 8

C

D

F

A

B

E

1 2 3 4

- Pin Functions(PM4009A1)( )Pin No. Pin Name I/O Function and Operation

1 VDD-D Power supply terminal for Digital blockpp y g2 TRESET I Reset input for TEST mode setting register

3 HSRDS O RDS detection output (high speed / low accuracy) 4 CLOCK O Clock output 5 DATA I Data input 6 RDS O RDS detection output (normal speed / high accuracy) 7 HSRDS2 O RDS detection output (high speed / low accuracy) 8 HSRESET I Reset input to HSRDS 9 D-SUB Digital block Sub-straight terminal 10 D-GND Digital block Ground terminal 11 XI Oscillator input terminal 12 XO Oscillator output terminal 13 TPIN3 I Test pattern input 14 TPIN2 I Test pattern input 15 RESET I Reset input 16 A-GND Analog block Ground terminal 17 A-SUB Analog block Sub-straight terminal 18 VREF AD reference voltage 19 REF AD input reference terminal 20 MPX IN Composite signal input terminal 21 TESTMODE I Input data of test mode setting register 22 MODECK I Clock input for TEST mode setting register 23 TPIN1 I Test pattern input 24 VDD-D Power supply terminal for Analog block

PM4009A1

1 12

1324

1 32

RE

FER

EN

CE

AN

OD

E

CA

TH

OD

E

NJM431U

NC ANODE NC

REFERENCECATHODE

1 2 3

45

VERF

NJM2373AF

RS-D7R—/EW5741 2 3 4

C

D

F

A

B

E

5 6 7 8

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

24

23

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

NC

A18

A17

A7

A6

A5

A4

A3

A2

A1

A0

CE

Vss

OE

D0

D8

D1

D9

D2

D10

D3

D11

A20

A19

A8

A9

A10

A11

A12

A13

A14

A15

A16

BYTE

Vss

D15/A-1

D7

D14

D6

D13

D5

D12

D4

Vcc

D15/A

-1 : Address input (output : 8 bit)

A0-A

12 : Address input

D0-D

15 : Data output

Vcc, V

ss : Pow

er supplyN

C : N

ot usedC

E: C

hip enable

OE

: Output enable

BY

TE

: 16/8 bits output select (L : 8 bit output)

PD8166A

VREF

+

1 2

4 3

VSS VDD

CDOUT

DelayCircuit

S-80929CNNB-G8Z

14 Y5

13 Y6

12 Y7

11 Y810 GND

9 A8

8 A7

1 g1

2 A1

3 A2

4 A3

5 A4

6 A5

7 A6

15 Y4

16 Y3

17 Y2

18 Y1

19 g2

20 VCC

TC74VHCT541AFK

IN-

1

2

5 VCC

VEE

IN+

OUT

3 4

OUT : Amplifier OutputVEE : Negative Power SupplyIN+ : Amplifier Noninverting InputIN- : Amplifier Inverting InputVCC : Positive Power Supply

MAX4412EXK

RS-D7R—/EW5 755 6 7 8

C

D

F

A

B

E

1 2 3 4

- Pin Functions (PD6556A)( )Pin No in Name I/O Function and Operation

1-3 A18-20 O Bus address output

7 7 O Bus address output8 A01 O Bus address output9 VSS GND

10-20 A02-12 O Bus address output21 VCC5 Power supply

22-24 A13-15 O Bus address output25 DSPDT Display data input26 KEYDT O Key data output

27-32 NC Not used33 AVCCAVCCA Power supply(AD)34 AVRHAVRHA Power supply(AD)35 AVSSAVSSA GND(AD)

36,37 KDT1,2 Key data input38,39 NC Not used

40 GND-40 GND41-43 NC Not used

44 FLASH FLASH input45 REMIN I Remote control signal inputg46 NC Not used

47-49 MD0-2 CPU mode settingg

55-63 NC Not used

67 OEL_RESET OEL controller reset output68 NC Not used69 ROM_RD O ROM read enable output70 OEL_WR OEL controller write output

71-73 NC O Not used74 RDY I Ready signal input75 CPU_RESET I Reset input

76-78 NC Not used

g

79 GND-79 GND80 XO Crystal oscillating element connection81 XI Crystal oscillating element connection82 VCC3 Power supply

83-98 D00-15 I/O Bus data input/output99,100 A16,17 O Bus address output

PD6556A

75

76

100

125

26

50

51

4-6 NC O Not used

I

I

50 NC Not used51 51 E2P_ROM data outputO52 52 E2P_ROM data inputI53 53 E2P_ROM clock outputO54 54 E2P_ROM chip select outputO

64 64 LED outputO65 ILMPWR Illumination output(Red)O66 ILMPWW Illumination output(White)O

O

O

I

RS-D7R—/EW5761 2 3 4

C

D

F

A

B

E

5 6 7 8

8 VCC

7 NC

6 TEST

5 GND4DO

3DI

2SK

1CS

Memory array Addressdecoder

Data register

Mode decoder logic

Clock pulsemonitoring circuit

Clock generator

Voltage detector

Output buffer

S-93C46BDOI-J8

RS-D7R—/EW5 775 6 7 8

C

D

F

A

B

E

1 2 3 4

- Pin Functions (TA2153FNS1)Pin No. Pin Name I/O Function and Operation

1 VCC - Power supply voltage terminal2 RFGC I RF amplitude adjustment control signal terminal3 GMAD I AGC amplifier frequency characteristic adjustment terminal4 FNI I Main beam amplifier input terminal5 FPI I Main beam amplifier input terminal6 TPI I Sub beam amplifier input terminal7 TNI I Sub beam amplifier input terminal8 MDI O Monitor photodiode amplifier input terminal9 LDO I Laser diode amplifier output terminal

10 SEL I APC circuit ON/OFF signal, LDO terminal control input terminal and bottom and peak detection frequency switching terminals

11 TEB I Tracking error balance adjustment signal input terminal12 2VRO O Reference voltage (2VRO) output terminal13 TEN I Tracking error signal generation amplifier reverse phase input terminal14 TEO O Tracking error signal generation amplifier output terminal15 SBAD O Sub beam addition signal output terminal16 FEO O Focus error signal generation amplifier output terminal17 FEN I Focus error signal generation amplifier reverse phase input terminal18 SEB I RFRP generation circuit mode switching terminal19 VRO O Reference voltage (VREF) output terminal20 RFRP O Signal generation amplifier output terminal for track count21 BTC I Bottom detection time constant adjustment terminal for RFCT signal

generation22 RFCT O RFRP signal center level output terminal23 PKC I Peak detection time constant adjustment signal for RFCT signal generation24 RFRPIN I Signal generation amplifier input terminal for track count25 RFGO O RF signal amplitude adjustment amplifier output terminal26 GVSW I AGC, FE or TE amplifier gain switching terminal27 AGCIN I RF signal amplitude adjustment amplifier input terminal28 RFO O RF signal generation amplifier output terminal29 GND I GND terminal30 RFN2 I RF signal generation amplifier input terminal

TA2153FNS1

115

16 30

TC9495F2S1

30

3150

51

80

81 100

1

RS-D7R—/EW5781 2 3 4

C

D

F

A

B

E

5 6 7 8

- Pin Functions (TC9495F2S1)Pin No. Pin Name I/O Function and Operation

1 TESTO Test mode terminal2 HSO O Replay speed flag output terminal3 UHSO O Replay speed flag output terminal4 EMPH O Emphasis flag output terminal for sub code Q data5 LRCK O Channel clock (44.1 kHz) output terminal6 Vss Digital ground terminal7 BCK O Bit clock output terminal8 AOUT O Digital audio data output terminal9 DOUT O Digital out output terminal

10 MBOV O Buffer memory over signal output terminal11 IPF O Correction flag output terminal12 SBOK O CRCC decision result output for sub code Q data13 CLCK I/O Clock input/output terminal for sub code P-W data read14 VDD Digital + power supply terminal (5 V)15 Vss Digital ground terminal16 DATA O Sub code P-W data output terminal17 SFSY O Replay-system frame sync signal output terminal18 SBSY O Sub code block sync output terminal19 SPCK O Clock for processor status signal read20 SPDA O Processor status signal output terminal21 COFS O Correction-system frame clock (7.35 kHz) output terminal22 MONIT O LSI internal signal output terminal23 VDD Digital + power supply terminal (5 V)24 TESIO0 I Test input/output terminal25 P2VRFF PLL-system only 2VREF terminal26 HSSW O The VREF voltage is reached for double or quad speed.27 ZDET O One-bit DAC zero detection flag output terminal28 PDO O Phase error signal issue between the EFM and PLCK signals29 TMAXS O TMAX detection result output terminal30 TAMX O TMAX detection result output terminal31 LPFN I Reverse input terminal of amplifier for lowpass filter32 LPFO O Output terminal of amplifier for lowpass filter33 PVREF PLL-system only VREF terminal34 VCOREF I VCO center frequency reference level terminal35 VCOF O Filter terminal for VCO36 Avss Analog-system ground terminal37 SLCO O Output terminal of DAC for data slice level generation38 RFI I RF signal input terminal39 AVDD Analog-system power supply terminal (5 V)40 RFCT I RFRP signal center level input terminal41 RFZI I Input terminal for RFRP signal zero cross42 RFRP I RF ripple signal input terminal43 FEI I Focus error signal input terminal44 SBAD I Sub beam addition signal input terminal45 TSIN I Test input terminal46 TEI I Tracking error input terminal47 TEZI I Input terminal for tracking error or zero cross48 FOO O Focus equalizer output terminal49 TRO O Tracking equalizer output terminal50 VREF Analog reference power supply terminal51 RFGC O RF amplitude adjustment control signal output terminal52 TEBC O Tracking balance control signal output terminal53 FMO O Feed equalizer output terminal54 FVO O Speed error signal or feed search EQ output55 DMO O Disc equalizer output terminal56 2VREF Analog reference power supply terminal57 SEL O APC circuit ON/OFF signal output terminal

RS-D7R—/EW5 795 6 7 8

C

D

F

A

B

E

1 2 3 4

Pin No. Pin Name I/O Function and Operation58 FLGA O External flag output terminal for internal signal monitor59 FLGB O External flag output terminal for internal signal monitor60 FLGC O External flag output terminal for internal signal monitor61 FLGD O External flag output terminal for internal signal monitor62 VDD Digital + power supply terminal (5 V)63 Vss Digital ground terminal64 IO0 O RF amplifier gain switching terminal65 IO166 IO2 I HOME detection switch input terminal67 IO3 O FocusDrv and signal output terminal68 DMOUT69 CKSE I Usually open70 DACT I DAC test mode terminal71 TESIN I Test input terminal72 TESIO1 I Test input/output terminal73 Vss Digital ground terminal74 PXI I DPS-system clock oscillator circuit input terminal75 PXO O DPS-system clock oscillator circuit output terminal76 VDD Digital + power supply terminal (5 V)77 Xvss Ground terminal for system clock oscillator circuit78 XI I System clock oscillator circuit input terminal79 XO O System clock oscillator circuit output terminal80 XVDD For system clock oscillator circuit + power supply terminal81 DVSR R channel D/A converting unit power supply terminal82 RO O R channel data forward rotation output terminal83 DVDD D/A converting unit power supply terminal (5 V)84 DVR Reference voltage terminal85 LO O L channel forward rotation output terminal86 DVSL L channel D/A converting unit power supply terminal87 TEST1 I Test mode terminal88 TEST2 I Test mode terminal89 TEST3 I Test mode terminal90 BUS0 I/O Data input/output terminal for microcomputer interface91 BUS1 I/O Data input/output terminal for microcomputer interface92 BUS2 I/O Data input/output terminal for microcomputer interface93 BUS3 I/O Data input/output terminal for microcomputer interface94 VDD Digital + power supply terminal (5 V)95 Vss Digital ground terminal96 BUCK I Clock terminal for microcomputer interface97 CEE I Chip enable signal for microcomputer interface98 TEST4 I Test mode terminal99 TSMOD I Test mode terminal

100 RST I Reset signal input terminal

Not used

Not used

RS-D7R—/EW5801 2 3 4

C

D

F

A

B

E

5 6 7 8

- Pin Functions (PE5238A1)Pin No. Pin Name I/O Format Function and Operation

1 bsck I/O /C P-Bus serial clock input/output2 BDATA I/O /C P-Bus serial data input/output3 CONT O C Servo driver power supply control output4 CDLOAD O C Load/Eject motor load control output5 CDEJET O C Load/Eject motor eject control output6 NC Not used (Open)7 reset Chip reset8 VDD1 Positive power supply of parts other than ports

(make potential the same as that of VDD0)9 X2 Connection for crystal oscillating system clock

10 X1 I Connection for crystal oscillating system clock11 VSS1 GND for parts other than ports

(make potential the same as that of VSS0)12-14 CBANK0-2 O C COMP IC bank setting output 0-2

15 crst O C COMP IC reset output16-18 NC Not used (Open)

19 SUBOK O C Output for sub code information being OK20,21 NC Not used (Open)

22 DSET O C Light output for disc set indicator23,24 NC Not used (Open)

25 DSPMUTE O C DOUT Mute output26-28 NC Not used (Open)

29 BRXEN I/O /C P-Bus receivability input/output30 NC Not used (Open)31 CD5VON O C CD+5V power supply control output

32,33 NC Not used (Open)34 emph O C Emphasis information output35 NC Not used (Open)36 xrst O C CD LSI reset output37 NC Not used (Open)38 xce O C CD LSI chip enable output39 XPCK O C CD LSI clock output

40-43 XPIO3-0 I/O /C CD LSI data input/output 3-044 NC Not used (Open)45 VSS0 GND for ports (make potential the same as that of VSS1)46 NC Connected directly to VSS047 NC Not used (Open)48 VDCONT O C VD power supply control output49 csens I Flap close sense input

50,51 NC Not used (Open)52 bsrq I/O /C P-Bus polling demand output

53,54 NC Not used (Open)55 VDD0 Positive power supply of ports

(make potential the same as VDD1)56 NC Not used (Open)57 VDSENS VD power supply sense input58 TEMP Temperature sense input59 DSCSNS Mechanism SW sense input60 NC Not used (Open)61 adena O C A/D reference voltage supply control output

62,63 NC Not used (Open)64 AVDD Positive power supply for A/D converter65 AVREF1 Reference voltage impression for A/D converter66 AVSS GND for A/D converter

67,68 NC Not used (Open)69-71 NC Connected to VSS0

RS-D7R—/EW5 815 6 7 8

C

D

F

A

B

E

1 2 3 4

Pin No. Pin Name I/O Format Function and Operation72 testin I Test program start input73 SPDLFG FG pulse signal input

74-76 NC Connected to VDD077 brst P-Bus reset input78 NC Connected to VDD0

79,80 NC Not used (Open)

801

20

21 40

41

60

61

PE5238A1

I

I

RS-D7R—/EW5821 2 3 4

C

D

F

A

B

E

5 6 7 8

No. Symbol I/O Explain1 STIND O stereo "Low" when the FM stereo signals are received.

indicator To be pulled up to the "VDD" at 47 kΩ.2 FMSD FM station Ω

detector Meanwhile, 10 kΩ should be used when taking diver FIX trigger from hereand "High: 0.9 VDD or more" and "Low: 250 mV or less".(Should satisfy the diver IC specifications)

3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47 kg Ω // 1 800 pF.4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36 kg Ω // 330 pF5 Rch O R channel FM stereo "R-ch" signal output or AM audio output.

output Add the specified de-emphasis constant.6 Lch O L channel FM stereo "L-ch" signal output or AM audio output.

output Add the specified de-emphasis constant.7 WC write control EEPROM write control. Writing permissible at "Low". Normally open.g8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS.g g9 NC Not used

10 VDD power Power supply pin for the digital section.supply DC 5 V +/- 0.25 V. Be careful about overlapping noise in the logic section.g g

11 DGND digital groundg g Grounding for the digital section.g g12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low"

To be pulled up to the "VDD" at 47 kΩ13 SL I/O signal level Received FM/AM signal level (strength) output.

Connect the specified load resistor and capacitor (10 kΩ + 39 kΩ // 4 700 pF)14 DI/DO I/O data input/ Data input/Data output

data output To be pulled up to the "VDD" at 47 kΩ15 CK I clock Ω16 CE1 I chip enable-1 AF· Ω17 NC Not used18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47 kΩ19 CREQ I current request Active at "Low". To be grounded at 47 kg Ω20 NC Not used21 COMP O FM composite signal output. r out < 100g Ω22 VCC power supply Analog section power supply pin.DC 8.4 V +/- 0.3 Vg23 LOCH I local highg FM local high pin. When seeking local high, apply 5 V together with "LOCL".g g g g24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5 V to the base of the NPN

transistor with which the specified resistor is being connected to the emitter.Keep it open in case of ordinary marketed models.

25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5 V to the base of theNPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use,do not drive it under FM.

26 RFGND RF groundg Grounding for the antenna section.g27 FMANT I FM antenna input FM antenna input. 75 Ω. Surge absorber is necessary.g28 AMANT I AM antenna input

Connect to the antenna through an L (LAU type) of 4.7 µH.To cope with the

(a coil of about 100 mH) + R (a resistor of 470 Ω to 2.2 kΩ) between the GND.

IC3EEPROM

28

27

FM/AM 1ST IF 10.7 MHzT51 Q51 CF51 CF52 CF53

IC1MIXER, IF AMP, DET.

6

21

18LDET

COMP

25 10 14 12 15 16 8 13 3

CF202

SL

NL1

IC 2 FM MPX

AMANT

FMANT

ATTT

ATT

AMRF

FMRF

IMG ADJ

RF ADJ

X90110.25 MHz

ANT ADJ

LOCL23

LOCH

AMDETMPXREF 41 kHz

AM 2ND IF450 kHz

CR

EQ

11 1

ST

IND

L ch

5R ch

9

NC

207

26 RFGND

- FM/AM Tuner Unit

O

42

RS-D7R—/EW5 835 6 7 8

C

D

F

A

B

E

1 2 3 4

7.3 OPERATIONAL FLOW CHART

VDD = 5 V

Power ON

bsens = L

asens = L

dsens = L

bsensPin 93

asensPin 92

dsensPin 2

SWVDD←LPin 1

ASENBO←HPin 28

Source keys operative

Completes power-on operation.(After that, proceed to each source operation)

SYSPWR←HPin 21

Startscommunication

with Grillemicrocomputer.

Source ON

300 ms

300 ms

In case of the above signal, the communication with Grille microcomputer may fail.If the time interval is not 300 msec, the oscillator may be defective.

RS-D7R—/EW5841 2 3 4

C

D

F

A

B

E

5 6 7 8

8. OPERATIONS

BAND button

MENU button

VOLUME

Closed state

AUX button

TUNER buttonCD button

TA button

ATT buttonThis lets you quicklylower volume level(by about 90%). Pressonce more to return tothe original volumelevel.

BAND buttonDISPLAY button

SOURCE button

RESET buttonVOLUME

EJECT/OPEN button

DISPLAY OFF indicatorSignal receiver

FUNCTIONbuttons 1 to 6

SHIFT button

RETURN button

Open state

Head unit

Remote control

In this system, the available functions and the menu display vary depending on thecondition of the remote controller in use. Opening the cover enables the SHIFT, RETURNand FUNCTION buttons 1 to 6 inside the unit.• When operating the remote control, be sure to point it to the signal receiver on the head unit. If not,it may not operate properly.

/ / / buttons

/ / / buttons

RS-D7R—/EW5 855 6 7 8

C

D

F

A

B

E

1 2 3 4

RS-D7R—/EW5861 2 3 4

C

D

F

A

B

E

5 6 7 8

RS-D7R—/EW5 875 6 7 8

C

D

F

A

B

E

1 2 3 4

Connecting the Units

This Product

ClearTo terminal always suppliedwith power regardless ofignition switch position.

RedTo electric terminal controlledby ignition switch (12 V DC)ON/OFF.

Clear/black (ground)To vehicle (metal) body.

Orange/whiteTo lighting switch terminal.

Yellow/blackIf you use an equipment with Mute function, wirethis lead to the Audio Mute lead on that equipment.If not, keep the Audio Mute lead free of anyconnections.

IP-BUS cable

Antenna jack

IP-BUS output (Black) 15 cm

15 cmIP-BUS input (Blue)

15 cm

Blue/whiteTo system control terminal of the poweramp or Auto-antenna relay control terminal(max. 300 mA 12 V DC).

Multi-CD player(sold separately)

(4 A)

Fuse resistor

Fuse resistor

Optical input (Blue)

Optical output (Black)

Fuse holder

Power cable connection

RS-D7R—/EW5881 2 3 4

C

D

F

A

B

E

5 6 7 8

This product

Tweeter Mid-range speaker Low-range speaker Subwoofer

IP-BUS output (Black) IP-BUS input (Blue)

Black

Black

Black

Blue

Blue

Blue

Black Blue Black

BlueBlack

Multi-CD player(sold separately)

Auxiliary equipment*1 IP-BUS cable*2 Optical cable*3 RCA cable (sold separately)

*1*1

*1*1

*1

*2

*2*2

*3

*3

Optical input (Blue)

Optical output (Black)

Digital integrated amplifier“RS-A9”(Sold separately)

DVD player(sold separately)

Display unit(e.g., “AVX-7600”(sold separately))

IP-BUS-RCA(e.g., “CD-RB20” (sold separately))

Digital amplifier“RS-A7”(Sold separately)

System connection

RS-D7R—/EW5 895 6 7 8

C

D

F

A

B

E

1 2 3 4

Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:

Portions to be cleaned Cleaning toolsg

CD pickup lenses Cleaning liquid : GEM1004

Cleaning paper : GED-008g p p

- Jigs List

Test DiscL.P.F.

TCD-784 Checking the gratingg g gChecking the gratingg g g (Two pieces)( )

Name Jig No. Remarks

- Grease List

GreaseGrease

GEM1029GEM1030

CD Mechanism ModuleCD Mechanism Module

Name Grease No. Remarks

RS-D7R—/EW5901 2 3 4

Date post:	01-Apr-2021
Category:	Documents
Upload:	others
View:	14 times
Download:	0 times

RS-D7R SYSTEM CONTROL TUNER/CD OPTICAL DIGITAL REFERENCE SYSTEM RS-D7R · RS-D7R — /EW5 3 56 7 8...

Documents