RubberGard™ EPDM Roof Systems Code Approval...

1 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

RubberGard™ EPDM Roof Systems Code Approval Guide

It is the responsibility of the Contractor/Consultant/Designer/Architect using this document to

validate/verify the included assemblies in the charts below meet the intent of design described by the

associated Firm’s (UL, FM, etc.).

Not all the information included in the RoofNav/UL assemblies will be listed in the charts below.

You must verify that all assemblies meet Firestone Building Products warranty requirements with the

associated regions technical team.

2 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Table of Contents Underwriters Laboratories (UL) External Fire Ratings ........................................................................................................... 5

General Notations .................................................................................................................................................................. 6

Firestone Ballasted System .................................................................................................................................................... 7

Firestone V‐Force Vapor Barrier System ................................................................................................................................ 7

Firestone Fully Adhered Platinum Systems ........................................................................................................................... 8

Firestone Fully Adhered RubberGard LS‐FR Systems ............................................................................................................. 9

Firestone Fully Adhered RubberGard EcoWhite Systems .................................................................................................... 10

Firestone Fully Adhered Fire Retardant RubberGard Systems ............................................................................................ 11

Firestone Fully Adhered RubberGard MAX Systems............................................................................................................ 12

Firestone Fully Adhered RubberGard MAX FR Systems ....................................................................................................... 12

Firestone Mechanically Attached Standard LS‐FR RubberGard Systems ............................................................................ 14

Firestone Mechanically Attached Fire Retardant RubberGard Systems.............................................................................. 15

Firestone Mechanically Attached RubberGard MAX Systems ............................................................................................. 15

Firestone Mechanically Attached RubberGard MAX FR Systems ........................................................................................ 17

Firestone RubberGard EPDM Self‐Adhered (SA) Systems ................................................................................................... 18

Firestone Mechanically Attached RubberGard LS‐FR SA Systems .......................................... Error! Bookmark not defined.

UL Internal Fire Ratings ........................................................................................................................................................ 19

Deck Constructions .............................................................................................................................................................. 19

"P" ASSEMBLIES ................................................................................................................................................................... 20

Factory Mutual General Information ................................................................................................................................... 20

Ground Roughness Definitions ............................................................................................................................................ 20

Exposure Category B: ........................................................................................................................................................... 20

Exposure Category C: ........................................................................................................................................................... 20

Exposure Category D: ........................................................................................................................................................... 21

General Notations ................................................................................................................................................................ 21

Field/Corner/Perimeter Definitions ..................................................................................................................................... 21

Perimeter and Corner Treatment of Adjoining Buildings .................................................................................................... 23

Prescriptive Enhancement Options: Perimeter and Corner ................................................................................................ 24

FM RoofNav Assemblies ...................................................................................................................................................... 25

Firestone EPDM – LS‐FR ‐ Fully Adhered Uplift Ratings ....................................................................................................... 25

Concrete Deck ‐ V‐Force Vapor Barrier System – Adhered Insulation – Adhered Membrane ............................................ 25

Firestone EPDM LS‐FR ‐ Fully Adhered Uplift Ratings .......................................................................................................... 27

Re‐Roof Construction ‐ Gypsum Deck – Adhered Insulation/Cover Board – Adhered Membrane ..................................... 27

3 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone EPDM – MAX/MAX FR ‐ Fully Adhered Uplift Ratings .......................................................................................... 28

Concrete Deck ‐ V‐Force Vapor Barrier System – Adhered Insulation ................................................................................ 28

Firestone RubberGard EPDM MAX/MAX FR ‐ Fully Adhered Uplift Ratings ........................................................................ 31


Firestone EPDM – Platinum ‐ Fully Adhered Uplift Ratings ................................................................................................. 32


Firestone EPDM – Platinum ‐ Fully Adhered Uplift Ratings ................................................................................................. 35


Firestone EcoWhite EPDM – Fully Adhered Uplift Ratings .................................................................................................. 36


Firestone EcoWhite EPDM ‐ Fully Adhered Uplift Ratings ................................................................................................... 37


Firestone EPDM – LS‐FR ‐ Fully Adhered Uplift Ratings ....................................................................................................... 38

Concrete Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane .................................................. 38

Firestone RubberGard EPDM LS‐FR/Self Adhered (SA)– Fully Adhered Uplift Ratings ....................................................... 39

Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board – Adhered Membrane .......................... 39

Firestone RubberGard EPDM LS‐FR/Self Adhered – Fully Adhered Uplift Ratings .............................................................. 42

Re‐Roof Construction – ........................................................................................................................................................ 42

Steel Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane ......................................................... 42

Firestone RubberGard EPDM MAX/MAX FR – Fully Adhered Uplift Ratings ....................................................................... 42






Re‐Cover Construction – ...................................................................................................................................................... 47


Firestone RubberGard EPDM MAX/MAX FR ‐ Fully Adhered Uplift Ratings ........................................................................ 47

Concrete Deck – Mechanically Attached Insulation – Adhered Insulation/Cover Board – Adhered Membrane ............... 47

Firestone RubberGard EPDM Platinum – Fully Adhered Uplift Ratings ............................................................................... 48


Firestone RubberGard EPDM Platinum – Fully Adhered Uplift Ratings ............................................................................... 51

4 | P a g e

D e c e m b e r 1 3 , 2 0 1 7



Firestone RubberGard EPDM Platinum ‐ Fully Adhered Uplift Ratings ............................................................................... 51

Concrete Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane .................................................. 51

Firestone EcoWhite – Fully Adhered Uplift Ratings ............................................................................................................. 52

Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board .............................................................. 52

Firestone – Fully Adhered Uplift Ratings ............................................................................................................................. 54

Re‐Cover Construction – Treated Wood Deck – Mechanically Attached Insulation/Cover Board ...................................... 54

Firestone RubberGard LS‐FR Mechanically Attached Uplift Ratings ................................................................................... 55


Firestone RubberGard MAX Mechanically Attached Uplift Ratings .................................................................................... 55


Firestone RubberGard MAX FR (Fire Retardant) Mechanically Attached Uplift Ratings ..................................................... 57


Firestone RubberGard MAX – QuickSeam R.MA. ‐ Mechanically Attached Uplift Ratings .................................................. 59


Firestone RubberGard MAX FR (Fire Retardant) – QuickSeam R.MA. – .............................................................................. 60

Mechanically Attached Uplift Ratings .................................................................................................................................. 60


Firestone RubberGard Platinum Mechanically Attached Uplift Ratings .............................................................................. 62


Factory Mutual Ballast Guidelines ....................................................................................................................................... 63

5 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Underwriters Laboratories (UL) External Fire Ratings All regional building codes and most local building code officials require that roofing systems meet minimum performance requirements when exposed to external fire sources. The accepted method for measuring external fire resistance is ASTM E-108. This test standard, and closely related standards such as Underwriters Laboratories UL-790 and Uniform Building Code 15-2, is used to determine the ability of a roof system to hinder the horizontal spread or vertical penetration of an external fire source. In accordance with these standards, all classified roof covering assemblies fall into one of the three following categories.

CLASS A: Includes roof coverings which are effective against severe fire exposures CLASS B: Includes roof coverings which are effective against moderate fire exposures CLASS C: Includes roof coverings which are effective against light fire exposures

Noncombustible Roof Decks (NC): Steel, Concrete, Poured Gypsum – require testing for horizontal spread of flame. Combustible Roof Decks (C): Wood, Plywood, Tectum – require testing for both horizontal spread and vertical penetration of flame. The following information has been referenced from the UL Online Certification Directory document: TGFU.GuideInfo Certified gypsum wallboard, any thickness, may be included in any roofing system without adversely affecting the certification. Insulations may be attached to the deck with fasteners, hot mopping asphalt or certified adhesive. Certified insulated systems may be installed over existing certified insulated systems when: 1) the new system is certified for use with the existing roof insulation type (glass fiber, perlite, wood fiber, foamed plastic, etc.), and 2) the total thickness of insulation in both systems does not exceed the maximum specified for the new system being applied. MAINTENANCE AND REPAIR SYSTEMS These roofing systems are composed of various types of roofing applications which are specifically limited for installation (recover) over existing roofing systems as specified. These systems may not meet certification requirements without being used over existing systems. Recovering may also be accomplished with certified new construction roofing systems where compatibility has been determined by test, by empirical data or by known performance properties of similar materials to the test methods. The following guidelines are provided to assist Authorities Having Jurisdiction in determining the suitability of a new construction roofing system as a recover system. Noncombustible Deck Construction: 1. Insulated roof systems may be utilized over any type of existing roof system and maintain its new construction rating when the

roof deck is noncombustible. 2. Insulated multiple-layered hot mopped, cold application or modified bitumen membrane new construction systems with a base

ply of Type G1 or Type G2 may be used over any existing roof system and maintain its new construction rating when the roof deck is noncombustible. The insulation may be omitted from the recover system.

3. Uninsulated multiple-layered hot mopped, cold application or modified bitumen membrane new construction systems with a base ply of Type G1 or Type G2 may be used over any existing uninsulated roof system and maintain its new construction rating when the roof deck is noncombustible.

Combustible Deck Construction: 1. Insulated roof systems certified for use over combustible deck can be used over any type of existing roof system and maintain

its new construction rating. 2. Insulated roof systems certified for use over noncombustible deck may be used over any type of Class A, B or C existing roof

systems. The resultant Class will be the lesser rating of the existing system or the new construction (recover) system. 3. Uninsulated multiple-layered hot mopped, cold application or modified bitumen membrane new construction systems with a

base ply of Type G1 or Type G2 may be used over any existing uninsulated roof system and maintain its new construction rating. The class of roof covering required by each regional building code depends upon many factors, including the use and location of the building and the type of construction. The local building authority should always be consulted as to what the roofing assembly classification will need to be for each roofing project. It should be noted that these classifications apply to roofing assemblies, and NOT the roofing membrane. A roofing membrane that is classified as part of a Class A assembly when installed over a particular insulation may not qualify as part of a Class A assembly with another insulation. The “UL Item Number” in the following listings has been added as a service to those who have the UL Building Materials Directory. It identifies the UL listing from which our Code Approval Guide listing derives (e.g., “A,FA,23” means Class A, Fully Adhered, item number 23; “B,MA,04” means Class B, Mechanically Attached, item number 04, etc.).

6 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

General Notations PLEASE NOTE: Not all FM-rated assemblies that use Firestone roofing products are eligible for the Firestone Red Shield

or Platinum Warranty. The Firestone standards, guidelines, and specifications regarding roofing system components and attachment for the warranty desired must be followed.

If a discrepancy occurs between this guide and UL Certifications, the published information located in the UL Certifications Directory at www.ul.com or Factor Mutual listings found at www.RoofNav.com should be adhered to and utilized.

If Firestone Building products requirements for warranty exceed those of the listed assemblies within this document, then the Firestone requirements should be followed.

(UL) Noncombustible decks Classifications are acceptable for use over combustible (15/32ʺ minimum plywood) decks when ½ʺ gypsum board or ¼ʺ DensDeck® are used directly over the deck with all joints staggered 6ʺ minimum from plywood joints.

The below stated assemblies may not be suitable for a Firestone Warranty. Prior to installation, contact a Firestone Representative for approval of assembly for warranty purposes.

(UL) HailGard Insulation is an acceptable alternative to all insulations in the following Classifications except where DensDeck is stated.

(UL) An optional layer of gypsum board may be placed between the insulation and roof deck on all ballasted systems. (UL) As an alternate a Firestone Ballast Paver® system may be issued in lieu of ballast and maintain the Classification of

any classified ballasted assembly. (UL) Fire Retardant Reinforced or RubberGard MAX FR EPDM membrane is an acceptable alternate to Fire Retardant

RubberGard in all applicable Classifications. (UL)Standard RubberGard membrane or RubberGard MAX FR EPDM membrane is an acceptable alternate to Standard

RubberGard in all applicable classifications. (UL)RubberGard MAX PT and RubberGard LS-FR PT are acceptable alternates for RubberGard MAX (45 or 60 mil) or

RubberGard LS-FR (45 and 60 mil) used in any fully adhered or mechanically fastened Class A, B or C roof covering system.

(UL) References to Type G1 and Type G2 ply and base sheets include "Ply IV", "Ply VI" (Type G1), "MB Base" (Type G2) in any of the following Classifications. Firestone "Venting Base Sheet" (Type G3) may be used in lieu of any Type G2 base in any applicable non-combustible Classification. The Firestone Channel Venting Base (mechanically attached only) may be used in all assemblies where the Firestone MB Base is listed on Non-combustible decks.

(UL & FM) Primers may be required. Please review the actual RoofNav and UL listings to verify. (UL & FM) Optional Coating/Surfacing may be available. Please review the actual RoofNav and UL listings to verify.

7 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Ballasted System Membrane: Any UL Classified RubberGard EPDM (Unreinforced or reinforced) Construction: New, Retrofit or Tear-off

Ballast Required: River bottom stone (¾ʺ to 1½ʺ dia.), crushed stone conforming to ASTM D-448 No. 4 or 3 may be applied at 1,000 lb/sq. or Firestone Ballast Paver. ASTM D-448 No. 1 or 2 may be applied at 1300 lb/sq.

Classification: Class A

UL Assembly Number

Deck Type

Insulation Assembly (Any one or combination)

Insulation Minimum Thickness

Maximum Slope

UL Item #

1. C Firestone ISO 95+ GL Any 2ʺ A, BA

1. C Any Polyiso, glass fiber, or wood fiber Any 2ʺ A, BA 1. NC Insulation: ISO 95+ GL, Wood Fiber or Perlite Any 2ʺ A, BA

Minimum thickness is for fully supported insulation. Metal deck flute width may require an increase in thickness. Consult insulation manufacturer on flute span capability. Option: Firestone Protection Mat may be installed either beneath or directly above the membrane. A thermal barrier is required below polystyrene insulation by the building codes when the polystyrene is placed over metal decks. An insulation separator is required over light weight insulating concrete.

Firestone V-Force Vapor Barrier System Membrane: Any UL Classified RubberGard EPDM (Unreinforced or reinforced)

Construction: New, Retrofit or Tear-off Classification: See Note 1

UL Assembly Number

Deck Vapor Barrier

Roofing System Maximum

Slope UL

Item #

1. NC

(See Note 1) “V-Force”,

self adhered Any Insulated UL Classified modified bitumen system, BUR system, EPDM, or TPO membrane system.

(See Note 1) (See Note 2)

A/B/C

Note 1: Classification (A, B or C) and maximum incline will be the same as that for the currently Classified insulated system, currently limited to a noncombustible deck. Note 2: Insulation may be adhered with Firestone "I.S.O. Twin Pack™", "I.S.O. Twin Pack Green", "I.S.O. Stick™" or "I.S.O. Spray™ R".

1A. C – 15/32


self adhered

Insulation (Optional): ISO 95+ GL, any thickness Barrier Board: ½ʺ DensDeck or DensDeck Prime Membrane: Any UL classified RubberGard EPDM

(See Note 1) (See Note 2)

A/B/C

Note 1: Classification (A, B or C) and maximum incline will be the same as that for the currently Classified insulated system, currently limited to a combustible deck. Note 2: Insulation may be adhered or mechanically attached with Firestone "I.S.O. Twin Pack", "I.S.O. Twin Pack Green", "I.S.O. Stick" or "I.S.O. Spray R".

1B. C – 15/32


self adhered

Insulation (Optional): ISO 95+ GL, any thickness Insulation (Required): 1ʺ min. Resista Membrane: Any UL classified RubberGard EPDM

¼ʺ (See Note 1) (See Note 2)

A/B/C

Note 1: Classification (A, B or C) and maximum incline will be the same as that for the currently Classified insulated system, currently limited to a combustible deck.

Note 2: Insulation may be adhered or mechanically attached with Firestone "I.S.O. Twin Pack", "I.S.O. Twin Pack Green", "I.S.O. Stick" or "I.S.O. Spray R".

8 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Fully Adhered Platinum Systems Membrane: RubberGard EPDM Platinum (90 mil) Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type Insulation Assembly

Insulation Minimum Thickness

Membrane Adhesive

Surfacing Maximum

Slope UL Item #

127. NC Insulation: ISO 95+ GL

Any BA 2004 Bonding Adhesive

None ½ʺ A, FA

128. NC

Barrier/Cover Board: DensDeck, DensDeck Prime

¼ʺ Any None 3½ʺ A, FA

Insulation (Optional): ISO 95+ GL

Any

129. NC

Insulation: HailGard Composite Board

1½ʺ Any None 2½ʺ

A, FA Insulation (Optional):

ISO 95+ GL Any


Any Any AcryliTop PC-100

2ʺ A, FA

131. NC

Barrier/Cover Board: DensDeck, DensDeck Prime

¼ʺ Any

AcryliTop PC-100

Unlimited A, FA Insulation (Optional): ISO 95+ GL

Any

132. NC

Insulation: HailGard Composite Board

1½ʺ Any

AcryliTop PC-100

Unlimited A, FA Insulation (Optional): ISO 95+ GL

Any

159. NC

Insulation: ISOGard HD ISOGard HD Composite Resista

½ʺ 1ʺ ½ʺ

BA 2004 Single-Ply

LVOC Single-Ply

1168 Water

Based – P

AcryliTop PC-100

2ʺ A, FA


Any

169. C

Barrier Board: DensDeck DensDeck Prime

¼ʺ ¼ʺ Water

Based – P None 3½ʺ A, FA


Any

170. NC Insulation (Optional): ISO 95+ GL

Any Water

Based – P None ½ʺ A, FA

171. NC

Cover Board: ISOGard HD ISOGard HD Composite

½ʺ

1ʺ Water

Based – P None ¾ʺ A, FA

Insulation (Optional): ISO 95+ GL Any

9 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Fully Adhered RubberGard LS-FR Systems Membrane: RubberGard LS-FR (45 mil and 60 mil) Adhesives: BA-2004(T) Bonding Adhesive, Water Based Bonding Adhesive P, EPDM Solvent-Free Bonding Adhesive, Single Ply

LVOC Bonding Adhesive or Single Ply LVOC Bonding Adhesive 1168 Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type Insulation Assembly

Insulation

Minimum Thickness

Membrane Adhesive

Surfacing Maximum

Slope UL

Item #

80. NC Insulation: Wood Fiberboard Insulation (Optional): ISO 95+ GL

½ʺ Any

None ¾ʺ A, FA

81. NC

Insulation (Optional): ISO 95+ GL Wood Fiberboard Perlite

Any None ½ʺ A, FA

82. C

Barrier Board: DensDeck DensDeck Prime Insulation (Optional): ISO 95+ GL

¼ʺ

Any

BA-2004 SP LVOC

SP LVOC 1168 WBBA-P

None Unlimited A, FA

123. C

Insulation: ISO 95+ GL (MA) Slip Sheet: Two Layers VersaShield Underlayment (PA) Two Layers VersaShield Underlayment FB-2S (PA)

Any

2 Layers

Opt. AcryliTop PC-100

½ʺ A, FA

124. C

Insulation: ISO 95+ GL (MA) Slip Sheet: Two Layers VersaShield FB-1S Underlayment (PA)

Any 2 Layers

Opt. AcryliTop

PC-100 ½ʺ A, FA

155. NC

Insulation: ISOGard HD ISOGard HD Composite Resista Insulation (Optional): ISO 95+ GL

½ʺ 1ʺ ½ʺ

Any

BA-2004 SP LVOC

SP LVOC 1168 WBBA-P


½ʺ A, FA

161. C

Insulation: ISOGard HD Composite Resista Insulation (Optional): ISO 95+ GL

1ʺ 1ʺ

Any

BA-2004 WBBA-P


½ʺ A, FA

172. C


¼ʺ ¼ʺ

Any

WBBA-P None ½ʺ A, FA


Any WBBA-P None ¼ʺ A, FA

215. NC

Insulation: Wood Fiber Insulation (Optional): ISO 95+ GL

1ʺ

Any EPDM SFBA None ½ʺ A, FA

216. NC


¼ʺ

Any EPDM SFBA None 3ʺ A, FA

217. NC Insulation: ISO 95+ GL Any EPDM SFBA None ¼ʺ A, FA

10 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Fully Adhered RubberGard EcoWhite Systems Membrane: RubberGard EcoWhite (45 mil – 90 mil) Adhesives: BA-2004(T) Bonding Adhesive, Water Based Bonding Adhesive P, EPDM Solvent-Free Bonding Adhesive, Single Ply

LVOC Bonding Adhesive or Single Ply LVOC Bonding Adhesive 1168 Unless Noted: EPDM Solvent-Free Bonding Adhesive, or Single Ply LVOC Bonding Adhesive Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type Insulation Assembly Insulation Minimum Thickness

Membrane Adhesive

Maximum Slope

UL Item #

145. NC Insulation: Wood Fiber

½ʺ 1ʺ A, FA

146. NC Insulation: Wood Fiber

½ʺ WBBA-P 1ʺ A, FA


Any WBBA-P ¾ʺ A, FA

148. C Barrier Board: DensDeck DensDeck Prime

¼ʺ 1½ʺ A, FA

149. NC Barrier Board: DensDeck DensDeck Prime

¼ʺ WBBA-P 1½ʺ A, FA

150. NC Barrier Board: OSB

7/16ʺ 1ʺ A, FA

151. NC Barrier Board: OSB

7/16ʺ WBBA-P 1ʺ A, FA

156. NC


Any BA 2004 SP LVOC SP LVOC

1168 WBBA-P

1ʺ A, FA Insulation: ISOGARD HD ISOGARD HD Composite Resista

½ʺ 1ʺ ½ʺ

161. C


Any BA 2004 WBBA-P

½ʺ A, FA Insulation: ISOGARD HD Composite Resista

1ʺ ½ʺ


Any ¾ʺ A, FA

172. C


Any

WBBA-P ½ʺ A, FA Barrier Board: DensDeck DensDeck Prime

¼ʺ ¼ʺ


¼ʺ WBBA-P ¼ʺ A, FA

215. NC


Any

EPDM SFBA ½ʺ A, FA Barrier Board: DensDeck DensDeck Prime

¼ʺ ¼ʺ

216. C


Any

EPDM SFBA 3ʺ A, FA Barrier Board: DensDeck DensDeck Prime

¼ʺ ¼ʺ


Any EPDM SFBA ¼ʺ A, FA

11 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Fully Adhered RubberGard EcoWhite Systems - continued Construction: Recover Classification: To retain Existing Class A, B or C rating

UL Assembly Number

Deck Type Insulation Assembly Insulation Minimum Thickness

Membrane Adhesive

Maximum Slope

UL Item #

1. C

Existing Class A, B or C BUR (Smooth Surface of Cap Sheet) to retain existing classification covered with: Insulation: ISOGARD HD ISOGARD HD Composite

½ʺ 1ʺ

1ʺ Based on existing system

Firestone Fully Adhered Fire Retardant RubberGard Systems Membrane: Fire Retardant RubberGard (45 mil and 60 mil) Adhesives: BA-2004 (T) Bonding Adhesive, Water Based Bonding Adhesive P, Unless Noted: EPDM Solvent-Free Bonding Adhesive, or Single Ply LVOC Bonding Adhesive Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type

Insulation Assembly Insulation

Minimum Thickness Membrane Adhesive

Maximum Slope

UL Item #

7. NC

Insulation (Optional): ISO 95+ GL Insulation: Wood Fiber (UL Classified)

Any

½ʺ 1½ʺ A, FA


Any 1ʺ A, FA

15. NC

Insulation (Optional): ISO 95+ GL Insulation: Wood Fiber (UL Classified)

Any

½ʺ 2ʺ A, FA

21. NC

Insulating Concrete: Deck covered with insulating concretes (poured in place) Cellular, Vermiculite, Perlite, Gypsum or Structural Insulation (Optional): Wood Fiber (UL Classified)

Any

½ʺ

1ʺ A, FA

156. NC

Insulation (Optional): ISO 95+ GL Insulation: ISOGARD HD ISOGARD HD Composite Resista

Any

½ʺ 1ʺ ½ʺ

BA 2004 SP LVOC SP LVOC

1168 WBBA-P

1ʺ A, FA

216. C

Insulation (Optional): ISO 95+ GL Barrier Board: DensDeck DensDeck Prime

Any

¼ʺ ¼ʺ

EPDM SFBA 3ʺ A, FA

12 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Fully Adhered RubberGard MAX Systems Membrane: RubberGard Max (min. 45 mil) Adhesives: BA-2004 (T) Bonding Adhesive, Water Based Boding Adhesive P, EPDM Solvent-Free Bonding Adhesive, Unless Noted: Single Ply LVOC Bonding Adhesive or Single Ply LVOC Bonding Adhesive 1168 Construction: New, Retrofit or Tear-off Classification: Class A NOTE: RubberGard Max FR is an acceptable Alternate to all UL listed assemblies that use RubberGard Max

UL Assembly Number

Deck Type



Maximum Slope

UL Item #

123. C

Slip Sheet: Two Layers VersaShield FB-1S Insulation: Firestone ISO 95+ GL Coating (Optional): AcryliTop PC-100

Any ½ʺ A, FA

124. C

Slip Sheet: Two Layers VersaShield Underlayment or VersaShield FB-2S Insulation: Firestone ISO 95+ GL Coating (Optional): AcryliTop PC-100

Any ½ʺ A, FA

161. C

Insulation (Optional): ISO 95+ GL Insulation: ISOGARD HD Composite Resista Surfacing (Optional): AcryliTop PC-100

Any

1ʺ

1ʺ

BA 2004 WBBA-P

½ʺ A, FA

172. C

Insulation (Optional): Any UL Classified Barrier Board: DensDeck DensDeck Prime

Any

¼ʺ ¼ʺ

WBBA-P ½ʺ A, FA


Any WBBA-P ¼ʺ A, FA

215. NC

Insulation (Optional): Any UL Classified Insulation: Wood Fiber

Any

1ʺ EPDM SFBA ½ʺ A, FA

216. C

Insulation (Optional): Any UL Classified Barrier Board: DensDeck DensDeck Prime

Any

¼ʺ ¼ʺ

EPDM SFBA 3ʺ A, FA


Any EPDM SFBA ¼ʺ A, FA

Firestone Fully Adhered RubberGard MAX FR Systems

Membrane: RubberGard Max (min. 45, 60, and 75 mil) Adhesives: BA-2004 (T) Bonding Adhesive, Single Ply LVOC Based Boding Adhesive

Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type



Maximum Slope

UL Item #

20. C

Insulation (Optional): ISO 95+ GL Barrier Board: DensDeck DensDeck Prime

Any

¼ʺ ¼ʺ

1½ʺ A, FA

26. NC

Insulation (Optional): Any UL Classified Insulation: Wood Fiber – UL Classified

Any

½ʺ

1” A, FA

13 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued: UL

Assembly

Number

Deck Type



Maximum Slope

UL Item #

66. NC

Insulation (Optional): Any Combination any, ISO 95+ GL, Wood Fiber, EPS or XPS Insulation: Wood Fiber – UL Classified

Any

½ʺ

2ʺ A, FA

89. NC

Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck or DensDeck Prime APA Rated Plywood or OSB

Any

½ʺ ¼ʺ

7/16ʺ

Unlimited A, FA

90. NC

Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck or DensDeck Prime APA Rated Plywood or OSB

Any

½ʺ ¼ʺ

7/16ʺ

WBBA-P 3ʺ A, FA

91. NC

Insulation (Optional): ISO 95+ GL Wood Fiber Glass Fiber Perlite

Any 3ʺ A, FA

92. NC

Insulation (Optional): ISO 95+ GL Wood Fiber Glass Fiber Perlite

Any WBBA-P 2½ʺ A, FA

93. C

Barrier Board: DensDeck or DensDeck Prime Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck or DensDeck Prime APA Rated Plywood or OSB

¼ʺ

Any

½ʺ ¼ʺ

7/16ʺ

Unlimited A, FA

94. C

Barrier Board: DensDeck Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck or DensDeck Prime APA Rated Plywood or OSB

¼ʺ

Any

½ʺ ¼ʺ

7/16ʺ

WBBA-P 3ʺ A, FA

95. C

Barrier Board: DensDeck or DensDeck Prime Insulation (Optional): ISO 95+ GL Wood Fiber Perlite

¼ʺ

Any 3ʺ A, FA

96. C

Barrier Board: Dens Deck or DensDeck Prime Insulation (Optional): ISO 95+ GL Wood Fiber Perlite

¼ʺ

Any WBBA-P 2½ʺ A, FA

123. C

Slip Sheet: Two Layers “VersaShield Underlayment” or “VersaShield FB-2S”, preliminary attached Insulation: ISO 95+ GL, mechanically attached

Any 1½” A, FA

124. C

Slip Sheet: Two Layers “VersaShield FB-1S”, preliminary attached Insulation: ISO 95+ GL, mechanically attached

Any ¾” A, FA

14 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued: UL

Assembly Number

Deck Type



Maximum Slope

UL Item #

158. NC

Insulation (Optional): Any UL Classified Polyisocyanurate Insulation: ISOGARD HD ISOGARD HD Composite Resista

Any

½ʺ 1ʺ ½ʺ

BA 2004 LVOC

LVOC – 1168

WBBA-P

2½ʺ A, FA

161. C

Insulation (Optional): ISO 95+ GL Insulation: ISOGARD HD Composite Resista

Any

1ʺ 1ʺ

BA 2004 WBBA-P

½ʺ A, FA

172. C

Insulation (Optional): Any UL Classified Barrier Board: DensDeck or DensDeck Prime

Any

¼ʺ

WBBA-P ½ʺ A, FA


Any WBBA-P ¼” A, FA

215. NC Insulation (Optional): Any UL Classified Insulation: Wood Fiber Board

Any 1ʺ

SFBA ½ʺ A, FA

216. C

Insulation (Optional): Any UL Classified Barrier Board: Dens Deck or Dens Deck Prime

Any

¼ʺ SFBA 3ʺ A, FA

217. NC Insulation: ISO 95+ GL Any SFBA ¼ʺ A, FA

Firestone Mechanically Attached Standard LS-FR RubberGard Systems Membrane: Standard RubberGard (45 mil and 60 mil) Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type


Minimum Thickness Maximum

Slope Notes UL Item #

53. NC

Insulation: ISO 95+ GL Wood Fiber Board Perlite

Any ½ʺ A, MA

55. NC Insulation (Optional): Any UL Classified Wood Fiber Board

Any ½ʺ

¾ʺ A, MA

63. C Slip Sheet: Two or more plies Atlas Roofing “FR-50” – MA

- ½ʺ A, MA

75. C Slip Sheet: Two layers “VersaShield Underlayment” or “VersaShield FB-2S”

- ½ʺ A, MA

76. C

Slip Sheet: Two Layers “VersaShield Underlayment” or “VersaShield FB-2S” – Preliminary Attachment Insulation: ISO 95+ GL – Preliminary Attachment

Any ½ʺ A, MA

77. C

Slip Sheet: Two Layers “VersaShield FB-1S” – Preliminary Attachment Insulation (Optional): ISO 95+ - Preliminary Attachment

Any ½ʺ A, MA

86. C


Any

1ʺ 1ʺ

½ʺ Optional: AcryliTop

A, MA

15 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Mechanically Attached Fire Retardant RubberGard Systems Membrane: Fire Retardant RubberGard (45 mil and 60 mil) Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type


Minimum Thickness

Maximum Slope Notes UL

Item #

7. NC

Insulation (Optional): ISO 95+ GL, Perlite, Wood Fiber Insulation: Wood Fiber – UL Classified

Any

½ʺ

1½ʺ A,

MA

8. NC

Insulation (Optional): EPS/XPS Dow Insulation: Wood Fiber FiberTop

Any

1ʺ ½ʺ

2¼ʺ A,

MA

Firestone Mechanically Attached RubberGard MAX Systems Membrane: RubberGard MAX Construction: New, Retrofit or Tear-off Classification: Class A NOTE: RubberGard Max FR is an acceptable Alternate to all UL listed assemblies that use RubberGard Max.

UL Assembly Number

Deck Type

Insulation Assembly Insulation Minimum Thickness


Item #

38. NC

Insulation (Optional): Perlite, Wood Fiber Insulation: Wood Fiber

3ʺ Max

½ʺ

1¼ʺ A, MA


Any ½ʺ A, MA

42. NC


Any

½ʺ 1¼ʺ A, MA

45. C

Barrier Board: Regular or Water-Resistant Wall Board Insulation (Optional): Perlite, Wood Fiber Insulation: Wood Fiber

½ʺ

Any ½ʺ

¼ʺ A, MA

63. C Slip Sheet: 2 or more plies Atlas Roofing FR 50 Mechanically Attached

½ʺ A, MA

64. NC

Insulation (Optional): Perlite, Wood Fiber Insulation: Wood Fiber

3ʺ Max

½ʺ 1¼ʺ A, MA

65. NC

Insulation Concrete: Poured in Place Cellular, Vermiculite, Perlite, Gypsum or Structural Insulation (Optional): Wood Fiber – UL Classified

½ʺ Max 1¼ʺ A, MA


Any ½ʺ A, MA

68. NC

Insulation (Optional): Any UL Classified polyisocyanurate or EPS/XPS Insulation: Woof Fiber – UL Classified

Any

½ʺ 1¼ʺ A, MA

70. C

Insulation (Optional): Any UL Classified Barrier Board: Water Resistant Wall Board Insulation (Optional): ISO 95+ GL

Any

½ʺ

Any

¼ʺ A, MA

75. C Slip Sheet: 2 Layers VersaShield Underlayment or VersaShield FB-2S – Preliminary Attachment

- ½ʺ Optional: AcryliTop PC-100

A, MA

16 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

UL Assembly Number

Deck Type



Item #

76. C

Slip Sheet: 2 Layers VersaShield Underlayment or VersaShield FB-2S – Preliminary Attachment Insulation: ISO 95+ GL

Any ½ʺ Optional: AcryliTop PC-100

A, MA

77. C

Slip Sheet: 2 Layers VersaShield Underlayment or VersaShield FB-1S – Preliminary Attachment Insulation (Optional): ISO 95+ GL

Any ½ʺ Optional: AcryliTop PC-100

A, MA

81. NC

Insulation (Optional): Any UL Classified Insulation: ISOGARD HD ISOGARD HD Composite Resista

Any ½ʺ 1ʺ ½ʺ

½ʺ Optional: AcryliTop PC-100

A, MA

86. C


Any

1ʺ 1ʺ

½ʺ Optional: AcryliTop PC-100

A, MA

Firestone Mechanically Attached RubberGard MAX Systems-Continued Membrane: RubberGard MAX Construction: Recover Classification: Class A

UL Assembly Number

Deck Type


Maximum Slope Notes UL Item #

1. C

Existing Roof System - Class A, B or C BUR (smooth surface of cap sheet) to retain existing classification covered with: Insulation: ISOGARD HD ISOGARD HD Composite

½ʺ

1ʺ ½ʺ

A, B, or C MR

7. NC

Existing Roof System – Class A, B or C, BUR, cap sheet or gravel surfaced, gravel to be maintained at 400 lb/sq. Insulation: Dow chemical USA STYROFOAM Ply Sheet: Type G1 or G2

1ʺ Max 1ʺ A, B, or C

MR

14. NC

Existing Roof System – Class A, B or C, cap sheet or gravel surfaced, gravel to be maintained at 400 lb/sq. Insulation: Dow Chemical USA STYROFOAM Ply Sheet: Type G1 or G2

1ʺ Max 1ʺ A, B, or C

MR

2. C

Existing Roof System – Class A, B or C Built-Up Roof System Slip Sheet: One layer VersaShield Underlayment – Preliminary Attachment

- ½ʺ A, B, or C

MR

8. C

Existing Roof System – Class A, B or C roofing system, to retain the existing Classification, is covered with: Slip Sheet (Optional): One or more layers Elk VersaShield, Atlas FR 10 or FR 50 Insulation (Optional): ISOGARD HD, Resista, ISO 95+ GL

Any

Max incline not to exceed that for which the existing roofing system is currently

classified.

A, B, or C

MR

17 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone Mechanically Attached RubberGard MAX FR Systems Membrane: RubberGard MAX FR (45 mil, 60 mil and 75 mil)

Construction: New, Retrofit or Tear-off Classification: Class A

UL Assembly Number

Deck Type


Maximum Slope

Notes UL Item #

21. C Insulation (Optional): Any UL Classified Barrier Board: Water Resistant Wallboard

Any ½ʺ

1½ʺ BB: Joints offset 6ʺ from

deck joints A

23. C

Barrier Board: Regular or Water-Resistant Wallboard Insulation (Optional): Any combination of the following: Perlite, Wood Fiber, Glass Fiber Insulation: Wood Fiber

½ʺ

3ʺ Max

½ʺ

¼ʺ BB: Joints offset 6ʺ from

deck joints A

28. C

Barrier Board: Regular or Water-Resistant Wallboard Insulation (Optional): ISO 95+ GL Insulation: Wood Fiber

½ʺ

Any

½ʺ

¼ʺ BB: Joints offset 6ʺ from

deck joints A

37. NC


Any

½ʺ

2ʺ A

47. NC

Insulation (Optional): Any combination of ISO 95+ GL, EPS/XPS, Perlite or Wood Fiber Insulation: FiberTop B Wood Fiber

No max.

½ʺ 2ʺ A

59. NC

Insulation (Optional): ISO 95+ GL Wood Fiber Perlite

Any 2½ʺ A

60. NC

Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck APA Rated Plywood or OSB

Any

½ʺ ¼ʺ

7/16ʺ

4ʺ A

61. C

Barrier Board: DensDeck Insulation (Optional): ISO 95+ GL Wood Fiber

¼ʺ

Any 2½ʺ A

62. C

Barrier Board: Dens Deck Insulation (Optional): Any UL Classified Insulation: Wood Fiberboard DensDeck APA Rated Plywood or OSB

¼ʺ Any ½ʺ ¼ʺ

7/16ʺ

4ʺ A

63. C Slip Sheet: Two or more plies Atlas Roofing “FR 50”

½ʺ Slip Sheet mech.

attached A

75. C Slip Sheet: Two layers “VersaShield Underlayment” or “VersaShield FB-2S”

1½ʺ Slip Sheet preliminary

attachment A

76. C

Slip Sheet: Two layers “VersaShield Underlayment” or “VersaShield FB-2S” Insulation: ISO 95+ GL

Any 2ʺ Preliminary Attachment A

77. C Slip Sheet: Two Layers “VersaShield FB-1S” Insulation (Optional): ISO 95+ GL

Any ¾ʺ Preliminary Attachment

A

85. NC

Insulation (Optional): Any UL classified Insulation: ISOGARD HD ISOGARD HD Composite Resista

Any

½ʺ 1ʺ ½ʺ

2½ʺ Optional Surfacing A

18 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

UL Assembly Number

Deck Type


Maximum Slope

Notes UL Item #

86. C


Any

1ʺ ½ʺ

½ʺ Optional Surfacing A

Firestone Mechanically Attached RubberGard MAX FR Systems-continued Construction: Recover

Classification: To retain existing Class A, Class B or Class C rating

UL Assembly Number

Deck Type


Maximum Slope

Notes UL Item #

1. C

Existing Roof System: Class A, B or C, BUR (Smooth surface cap sheet) to retain existing classification covered with: Insulation: ISOGARD HD ISOGARD HD Composite

½ʺ 1ʺ

2½ʺ A, B or C MR

8. NC Class A, B or C, cap sheet or gravel surfaced, loose gravel may be removed 1ʺ Max 1ʺ A, B or C

MR

Firestone RubberGard EPDM Self-Adhered (SA) Systems Membrane: RubberGard EPDM SA (45 – 80 mil) Construction: New or Tear-off Classification: Class A

UL Assembly Number

Deck Type


Maximum Slope

Notes UL Item #

181. C Insulation (Optional): Any UL Classified Barrier Board: Dens Deck or DensDeck Prime

Any

¼ʺ 2ʺ A

181A. NC Insulation: ISO 95+ GL Any ¼ʺ A

181B. NC Insulation: ISO 95+ GL Cover Board: ISOGARD HD

Any

½ʺ ½ʺ A

44. NC Insulation: ISO 95+ GL or RESISTA Any ¼ʺ B

46. NC Insulation: ISO 95+ GL or RESISTA Any ½ʺ B

19 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

UL Internal Fire Ratings To determine the resistance of a building to internal sources of fire, Underwriters Laboratories has conducted extensive testing and classification of wall, floor/ceiling and roof/ceiling assemblies. UL classified assemblies are rated according to the time in hours the assembly will contain a fire and still maintain structural integrity. Testing is conducted in accordance with UL Standard 263 (ASTM E-119), which is recognized by all major building codes. Roof/Ceiling Assemblies are listed in the UL Fire Resistance Directory - Vol. 1 under the prefix “P” and are classified by hourly fire rating according to the type of protection used to contain a fire:

Assembly Protection Used

P000 – P099 Concealed grid suspended ceiling

P200 – P299 Exposed grid suspended ceiling

P400 – P499 Metal lathe (plaster) ceiling

P500 – P599 Gypsum board ceiling

P600 – P699 Miscellaneous fireproofing

P700 – P799 Spray-Applied Resistive Material

P800 – P899 Spray-Applied Resistive Material

P900 – P999 Unprotected concrete or composite decks It should be noted that the roof membrane forms only a small part of the total roof/ceiling assembly. For a structure to qualify for a “P” Assembly or Roof Deck Construction, all materials used to construct the assembly (including roof decking, ceiling materials, light fixtures, duct work and structural support members) must be UL classified and installed as described in the appropriate UL Directories. The insulations listed with each of the following “P” Assemblies are not, in most cases, the only UL accepted insulations for that assembly. Consult the UL Fire Resistance Directory - Vol. 1 for “P” Assembly information and the UL Roofing Materials and Systems Directory for Roof Deck Construction information, or call Firestone Technical Services for additional accepted insulations. UL has indicated on page 8 of the 2008 Fire Resistance Directory - Vol. 1 that "Class A, B or C roof coverings consisting of hot mopped or cold applied bituminous materials or a roof covering material classified under 'Roofing Membranes' (CHCI) may be applied directly to the concrete or wood surface of floor designs being used as roofs without a reduction of fire resistance ratings." They further state on page 8 that "Roof insulation is to be carefully controlled relative to manufacturer, type and thickness as specified. Less than the specified thickness could result in higher temperatures on the roof covering while a greater thickness of insulation could cause earlier structural failure. Classified polystyrene insulation, with a density of 5 pcf or less, may be placed on concrete floors or structural concrete roofs without reducing the assembly rating. When polyisocyanurate insulation is used over concrete in D 900 Series Designs, the unrestrained beam rating shall be increased by a minimum of ½ hour." Roof Deck Constructions are listed in the UL Roofing Materials and Systems Directory and are rated according to the interior flame spread of the assembly as compared to the flame spread of a typical built-up roof installed over a metal deck (UL 1256). Roof Deck Constructions may also be classified according to wind uplift performance. The fire rating of a UL Roof Deck Construction is similar to the Factory Mutual Class I internal fire (calorimeter) rating and they are deemed equivalent by the Model Building Code Agencies. Deck Constructions

Firestone EPDM Roofing Systems are classified for use in the following Deck Construction (tested to UL 1256). 1, 2, 9, 14, 120, 123, 158, 200, 219, 237, 260, 276, 289, 292, 325, 374, 411, 412, 413, 419, 421, 440, 441, 444, 457, and 458. Consult Roof Deck Constructions (TGKX) in the UL Roofing Materials and Systems Directory, your regional technical coordinator or the Firestone Codes Department for an acceptable insulation for use in these constructions.

20 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

"P" ASSEMBLIES

Firestone's EPDM Roofing Systems are classified for use in the following Hourly Roof / Ceiling Designs ("P" Designs). P211, P214, P215, P216, P224, P225, P227, P229, P230, P231, P232, P235, P237, P241, P242, P246, 251, P259, P405, P406, P407, P410, P411, P505, P507, P508, P509, P510, P511, P 513, P514, P519, P701, 708, P709, P710, P711, P712, P713, P717, P718, P719, P720, P722, P 723, P724, P725, P726, P727, P728, 729, P730, P731, P732, P733, P734, P735, P736, P737, P738, P739, P801, P802, P803, P804, P805, P810, 811, P812, P813, P814, P815, P816, P817, P818, P819, P822, P823, P825, P826, P827, P902, P903, P904, 905, P906 P907, P908, P909, P910, P911, P912, P913, P914, P915, P916 P917, P918, P919, P920, P921, P922, P923, P924, P925, P926, P927, P928, P929, P930, P931. Consult Fire Resistance Ratings (BXUV) in the UL Fire Resistance Directory, your regional technical coordinator or the Firestone Codes Department for an acceptable insulation, thickness and additional requirements. NOTE: The accepted insulation must be used in a UL Class A, B or C rated roofing assembly. UL acceptable system (e.g. adhering EPDM to Perlite or Fiberglas) listed for "P" design may not be approved for installation and warranty by Firestone. Contact Firestone Specifications and/or your Firestone Regional Technical Coordinator concerning acceptance. Please refer to Pages 3 through 35 of this Approval Guide to determine the appropriate insulation/membrane assembly.

Factory Mutual General Information Factory Mutual Class 1 Approvals cover a wide range of testing of roofing products, including tests for fire resistance, corrosion resistance, fuel contribution and hail damage, Factory Mutual Approvals are known best for the uplift resistance, 1-60, 1-90, etc. afforded by an FM Approved roofing assembly:

FM 1-60 assemblies have been tested to withstand 60 psf air pressure applied for a period of one minute

as well as one minute at the 30 and 45 psf levels. FM 1-90 assemblies have been tested to withstand 90 psf air pressure applied for a period of one minute

as well as one minute at the 30, 45, 60 and 75 psf levels. Higher uplift ratings are possible based on the deck type and its attachment, fastener density and row

spacing where applicable.

When Factory Mutual 1-60 or 1-90 uplift ratings are specified, additional insulation attachment and reduced perimeter and corner batten (in-seam plate or batten for Reinforced Systems) spacing will/may be required. Consult the current edition of Factory Mutual Loss Prevention Data Sheets 1-28 and 1-29 for instructions for determining the required corner and perimeter dimensions and reduced spacing and increased fastener densities. Ground Roughness Definitions

The descriptions below are based on information in ASCE 7. While information on this subject in the body of that standard is relatively brief, the designer must read the considerable additional information provided in the related commentary section of that document, particularly when then exposure is not obvious. Exposure Category B:

A. The exposing terrain should include urban and suburban areas, wooded areas, or other terrain with numerous closely spaced obstructions having the size of single-family dwellings or larger.

B. Use of this exposure category should be limited to those areas for which the above terrain prevails in all directions for a distance of at least 2600ft (800 m) or 20 times the height of the building or other structure, whichever is greater.

C. Limited openings in this terrain, such as small parking lots, roads, road intersections, playing fields, underdeveloped lots, and tree clearings can be tolerated. For openings that exceed 600ft (180 m) in total length measured radially from the building and 165ft [50 m] in width, use surface roughness exposure C.

D. For buildings whose height is less than or equal to 30ft (9.1 m), the prevailing exposure B distance may be reduced to 1500ft (460 m).

E. In cases where the difference between exposures B and C is not obvious, use exposure C.

Exposure Category C:

NOTE: In cases where the difference between exposure B and C is not obvious, use exposure C.

21 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

For Exposure Category C to be used:

A. The exposing terrain should be open with scattered obstructions having heights generally less than 30ft (9 m), such as flat, open country and grasslands, and in all cases where exposures B and D do not apply.

B. This also includes where surface roughness exposure B terrain is interrupted by clearings (parking lots, wide roads, road intersections, playing fields, underdeveloped lots, tree clearings, etc.) of greater than 600ft (180 m) in total length measured radially from the building and exceeding 165ft (50 m) in width.

Exposure Category D:

NOTE: Some examples of D exposures include inland waterways, the Great Lakes, and coastal areas. See fig. 3.2.2.3 in FM Global LPDA 1-28 for examples of Exposure D requirements. For Exposure Category D to be used in determining the design wind pressure, all the following must be met:

A. The terrain upwind of the structure must be flat, unobstructed areas or water surfaces including smooth mud flats, salt flats, and unbroken ice and is present in the upwind direction for a distance greater than approximately 5000ft (1500 m) or 20 times the building height, and

B. The building must be within the greater of 600ft (180 m) or 20 times the building or structure height from the terrain (see Fig. 3.2.2.3), even if the terrain between the building and the terrain described in A. above would otherwise be considered B or C.

General Notations

PLEASE NOTE: Not all FM-rated assemblies that use Firestone roofing products are eligible for the Firestone Red Shield, Red Shield Medallion, or Platinum Warranty. The Firestone standards, guidelines, and specifications regarding roofing system components and attachment for the warranty desired must be followed. RoofNav® assemblies are summarized in the following tables; however, an assembly search should be conducted to confirm the attachment rates and requirements set for in the approval number. In all occasions, should a discrepancy occur between this guide and RoofNav, the published information located in the approval at www.roofnav.com should be adhered and utilized. Additionally, please be aware that the following assemblies typically are in reference to the field of the roof rating and attachment. Please refer to FM Global Loss Prevention Data Sheet 1-28 and 1-29 to determine the requirements for additional fastening requirements in the perimeter and corner. In all cases, when the project is Factory Mutual insured, please consult the FM agent assigned to the review of the project to ensure compliance. The below stated assemblies may not be suitable for a Firestone Warranty. Prior to installation, contact a Firestone Representative for approval of assembly for warranty purposes. It is acceptable to use multiple layers of FM Approved insulation, mechanically secured through all layers, provided all the following are true:

All layers are the same insulation; The total insulation thickness is not greater than the maximum FM Approved thickness of the insulation; The mechanical fastening and wind uplift rating are per the FM Approval of the top layer; and, The roof cover/insulation/fastener combination is FM Approved.

Water Based Bonding Adhesive-P (WBBA-P) is the equivalent to Water Based Bonding Adhesive-S (WBBA-S).

Field/Corner/Perimeter Definitions

The following diagram is direct form the FM Global Property Lost Prevention Data Sheet 1-28. This outlines how to calculate your perimeter and corner areas based on the building size and relative conditions.

22 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

©2015 Factory Mutual Insurance Company. All rights reserved.

23 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Perimeter and Corner Treatment of Adjoining Buildings

24 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Prescriptive Enhancement Options: Perimeter and Corner

2.2.10 Above-Deck Roof Components (Other Than LWIC) 2.2.10.1 Wind Uplift Resistance 2.2.10.1.1 Provide one of the following options to secure the roof perimeter and corners (Zones 2 and 3):

A. Use a roof system with an FM Approval wind uplift rating that is acceptable for the field, perimeter, and corners per the Ratings Calculator of RoofNav or DS 1-28. That could entail using a system throughout the entire roof that had a wind rating adequate for the corners, or using a system that has a varied fastener spacing and multiple wind ratings that are adequate for the field, perimeter, and corner areas.

B. Use the appropriate prescriptive recommendation noted in Section 2.2.10.1.2. In either case, ensure any whole or partial insulation board or roof cover/base sheet width (when the roll is parallel to the building edge) that falls within the calculated perimeter or corner has the increased securement applied over the entire board or roof cover/base sheet width.

2.2.10.1.2 Use prescriptive enhancements for perimeter and corner areas (for all deck types) where roof covers are adhered to some combination of insulation or cover board if one of the following conditions applies:

A. The recommended field-of-roof rating needed per DS 1-28 in any location does not exceed Class 1-75 (3.6 kPa), or

B. The building is in a non-hurricane-prone region (see Appendix A) and the recommended field-of-roof rating per DS 1-28 does not exceed Class 1-90 (4.3 kPa).

2.2.10.1.2.1 For either of the above conditions, increase the securement over the FM Approved field-of-roof spacing as follows:

A. For assemblies using insulation fasteners, increase the number of fasteners per board by: 1. 50% minimum in the roof perimeter, but at least one fastener per 2ft², tm1 per 0.19 m²). It is not necessary to

install fasteners closer than one per 1ft² (1 per 0.09 m²). 2. One fastener per 1ft² (1 per 0.09 m²) in corner areas. 3. Round up to the next whole number of fasteners, if

necessary 3. Round up to the next whole number of fasteners, if necessary

B. For components adhered with adhesives applied in ribbons, spots, etc., reduce the spacing between ribbons or spots over the FM Approved spacing for the given wind rating as noted below (round down to a dimension that is practical with respect to board sizes, applicators, etc.):

1. In the roof perimeter, not more than 60% of the field-of-roof spacing between rows, or area 2. In the roof corners, not more than 40% of the field-of-roof spacing between rows, or area NOTE: If the FM Approval wind rating already meets the higher criteria for the perimeter or corner area, no further reduction is needed in those areas.

Examples of Prescriptive Enhancements (Fasteners): 1-90 and below for 4' x 8' boards

Field Perimeters Corners

Field Perimeters Corners

8 16 32 16 24 32

10 16 32 18 27 32

12 18 32 20 30 32

15 23 32

25 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

FM RoofNav Assemblies Firestone EPDM – LS-FR - Fully Adhered Uplift Ratings Concrete Deck - V-Force Vapor Barrier System – Adhered Insulation – Adhered Membrane

Uplift Deck Type Cover Board and

Insulation

Cover Board and Insulation

Attachment Membrane

Membrane Attachment

RoofNav Number

1-75

IF: NC EF: A

Slope: ½ʺ

Concrete Min. 2,500 psi

Min. 2ʺ thick

Insulation: 1.5ʺ-36ʺ thick, 4' x 4'

boards ISO 95+ GL

ISO 95+ GL (Taper) Resista

Vapor Barrier: V-Force (Self Adhered)

Adhered at 12ʺ o.c.: ISO Spray R

.045 mil. min. RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA-P

371174-0-0

EPDM SFBA 384176-0-0

1-75

IF: NC EF: A

Slope: ¼ʺ


Min. 2ʺ thick

Cover Board: ½ʺ, 4' x 4' boards,

ISOGARD HD 1ʺ-2.5ʺ, 4' x 4' boards,

ISOGARD HD COMPOSITE


boards ISO 95+ GL





.060 mil.

RubberGard LS-FR PT

BA-2004 EPDM SFBA

Single-Ply LVOC

Single-Ply LVOC 1168

WBBA-P

371151-0-0

1-90

IF: NC EF: A

Slope: ½ʺ


Min. 2ʺ thick


boards ISO 95+ GL





.060 mil.

RubberGard LS-FR PT

BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA-P

370560-0-0

EPDM SFBA 384154-0-0

1-315

IF: NC EF: A

Slope: ½ʺ


Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)

Adhered at 12ʺ o.c.: ISO Twin Pack


.060 mil.

RubberGard LS-FR PT

BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168

102219-0-0

1-330


Min. 2ʺ thick

Cover Board: ¼ʺ min, 4' x 4' boards, DensDeck/Securock

Insulation:

1.5ʺ-36ʺ thick, 4' x 4' boards

ISO 95+ GL ISO 95+ GL (Taper)

Cover Board and Insulation:

Adhered at 20-25 lb/sq. Hot Asphalt

Primed Deck:

Concrete Primer, Asphaltic

Permeable


.060 mil.

RubberGard LS-FR PT

BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168

47789-0-0

1-465

IF: NC EF: A

Slope: 1ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick

Cover Board:

¼ʺ min, 4' x 4' boards,

DensDeck/DensDeck Prime/ Securock

Insulation:



Adhered at 12ʺ o.c.:

ISO Stick

Primed Deck:


Permeable

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC

228430-0-0

26 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane Membrane Attachment

RoofNav Number

1-465

IF: NC EF: A

Slope: 1ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick

Insulation:

¼ʺ min, 4' x 4' boards,

DensDeck/Securock


ISO Twin Pack


.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


100971-0-0

1-255

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick

Cover Board: .438ʺ-.5ʺ

APA Rated OSB Insulation:



Resista


ISO Spray R

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

EPDM SFBA

Single-Ply LVOC


308435-0-0

1-525

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper) Vapor Barrier: V-Force (Self

Adhered) Primer (permeable):

SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


297178-0-0

1-525

IF: NC

EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


ISOGARD HD 1ʺ-2.5ʺ, 4x4 boards,



boards ISO 95+ GL

ISO 95+ GL (Taper) Vapor Barrier: V-Force (Self


SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

SFBA

Single-Ply LVOC

WBBA-P

298272-0-0

1-525

IF: NC

EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ

thick

Cover Board: ½ʺ, 4' x 4' boards

DensDeck DensDeck Prime

Securock Insulation:



Vapor Barrier: V-Force (Self


SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.045

mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC

297159-0-0

27 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-540

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)

Adhered at 12ʺ o.c.: ISO Stick

Primed Deck:


Permeable


.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC 228465-0-0

1-555

IF: NC

EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


ISOGARD HD 1ʺ-2.5ʺ, 4' x 4' boards

ISOGARD HD Composite Insulation:

1ʺ-36ʺ thick, 4' x 4' boards ISO 95+ GL

ISO 95+ GL (Taper)


ISO Spray R


.060 mil.

RubberGard LS-FR PT

BA-2004

EPDM SFBA

Single-Ply LVOC


WBBA-P

308236-0-0

1-675

IF: NC EF: A

Slope: ½ʺ

Concrete Min.

2,500 psi Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper) Vapor Barrier:

V-Force (Self Adhered) Primer (permeable):

SA-LVOC SA-SB

V-Force SB


ISO Twin Pack ISO Stick


.060 mil.

RubberGard LS-FR PT

BA-2004 Single-Ply LVOC

296334-0-0

1-690

IF: NC EF: A

Slope: 1ʺ

Concrete Min.


Cover Board: ¼ʺ, 4' x 4' boards

DensDeck Securock Insulation:



Full Spray.: ISO Spray R

1.04 gal/square


.060 mil.

RubberGard LS-FR PT


135774-0-0

1-780

IF: NC EF: A

Slope: ½ʺ


boards ISO 95+ GL

ISO 95+ GL (Taper)


1.04 gal/square


.060 mil.

RubberGard LS-FR PT


Single-Ply LVOC 1168 62382-0-0

Firestone EPDM LS-FR - Fully Adhered Uplift Ratings Re-Roof Construction - Gypsum Deck – Adhered Insulation/Cover Board – Adhered Membrane

Uplift Deck Type




RoofNav Number

1-90

IF: 1

EF: A

Slope: ½ʺ

Gypsum

Insulation:

¼ʺ, 4' x 4' boards

DensDeck

Securock


ISO Twin Pack

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


WBBA-P

100864-0-0

28 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-90

IF: 1 EF: A

Slope: 1ʺ

Gypsum


DensDeck Securock

Insulation (Top Layer): 1.5ʺ-8ʺ thick, 4' x 4'

boards ISO 95+ GL


Insulation (Bottom Layer): 1.5ʺ-4ʺ thick, 4' x 4'

boards ISO 95+ GL




.060 mil.

RubberGard LS-FR PT


Single-Ply LVOC 1168 WBBA-P

100861-0-0

1-90

IF: 1

EF: A

Slope: ¼ʺ

Gypsum






Resista


ISO Twin Pack

ISO Stick

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


WBBA-P

262899-0-0

1-90

IF: 1

EF: A

Slope: ½ʺ

Gypsum


ISOGARD HD 1ʺ-8ʺ, 4' x 4' boards




Resista


ISO FIX II

ISO Spray R

ISO Twin Pack

ISO Stick

.045 mil. min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


WBBA-P

420488-0-0

Firestone EPDM – MAX/MAX FR - Fully Adhered Uplift Ratings Concrete Deck - V-Force Vapor Barrier System – Adhered Insulation

Uplift Deck Type




RoofNav Number

1-75

IF: NC

EF: A

Slope: ¼ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


ISOGARD HD 1”-2.5ʺ, 4x4 boards,



boards ISO 95+ GL




ISO Spray R

.045 mil. min.

RubberGard MAX

RubberGard MAX FR

RubberGard MAX PT

BA-2004

SFBA

Single-Ply LVOC


WBBA-P

371151-0-0

29 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-255

IF: NC

EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


APA Rated OSB


boards ISO 95+ GL

ISO 95+ GL (Taper) Resista*


ISO Spray R

.045 mil. min.

RubberGard MAX

RubberGard MAX PT

BA-2004

EPDM SFBA

Single-Ply LVOC


308435-0-0

1-315

IF: NC EF: A

Slope: ¼ʺ

Concrete Min.

2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)


ISO Twin Pack

.045 mil. min. RubberGard MAX RubberGard MAX

PT BA-2004 Single-Ply LVOC


94602-0-0

1-315

IF: NC EF: A

Slope: 2.5ʺ

.045 mil. min. RubberGard MAX

FR 107603-0-0

1-330

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


DensDeck Securock

Insulation:



Cover Board and Insulation:

Adhered at 20-25 lb/sq.

Hot Asphalt

Primed Deck:


Permeable

.045 mil. min.

RubberGard MAX

RubberGard MAX PT BA-2004

Single-Ply LVOC


47786-0-0

1-330

IF: NC EF: A

Slope: 4ʺ

.045 mil. min.

RubberGard MAX FR

47802-0-0

1-465

IF: NC EF: A

Slope: ½ʺ

Concrete Min.








ISO Stick


Permeable

.045 mil. min. RubberGard MAX RubberGard MAX

PT BA-2004

Single-Ply LVOC

228424-0-0

1-465

IF: NC EF: A

Slope: 4ʺ


FR 228439-0-0

1-465

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick

Insulation: ¼ʺ, 4' x 4' boards

DensDeck Securock


ISO Twin Pack

.045 mil. min.

RubberGard MAX

RubberGard MAX PT

BA-2004

Single-Ply LVOC


99842-0-0

1-465

IF: NC EF: A

Slope: 4ʺ

.045 mil. min.

RubberGard MAX FR

110624-0-0

30 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-495

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick






ISO Stick


Permeable

.045 mil. min.

RubberGard MAX FR

BA-2004

EPDM SFBA

Single-Ply LVOC


228350-0-0

1-525

IF: NC EF: A

Slope: ¼ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL



Primer (permeable): SA-LVOC

SA-SB V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.045 mil. min.

RubberGard MAX

RubberGard MAX PT

BA-2004

Single-Ply LVOC


297177-0-0

1-525

IF: NC EF: A

Slope: ¼ʺ

Concrete Min. 2,500

psi Min. 2ʺ thick





boards ISO 95+ GL



SA-LVOC SA-SB

V-Force SB




RubberGard MAX PT

BA-2004 SFBA

Single-Ply LVOC WBBA-P

298271-0-0

1-525

IF: NC EF: A

Slope: ½ʺ

Concrete Min. 2,500

psi Min. 2ʺ thick








SA-SB V-Force SB




.045 mil.

RubberGard MAX PT


397159-0-0

1-540

IF: NC EF: A

Slope: ¼ʺ

Concrete Min. 2,500

psi Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)


Concrete Primer,

Asphaltic Permeable


.045 mil.

RubberGard MAX PT BA-2004 Single-Ply LVOC

228463-0-0

1-540

IF: NC EF: A

Slope: 2.5ʺ

.045 mil. min. RubberGard MAX FR

228469-0-0

31 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-555

IF: NC EF: A

Slope: ¼ʺ Concrete Min. 2,500 psi Min. 2ʺ thick




Insulation: 1ʺ-36ʺ thick, 4' x 4'

boards ISO 95+ GL




.045 mil.


EPDM SFBA Single-Ply LVOC


308235-0-0

1-555

IF: NC EF: A

Slope: 2.5ʺ

.045 mil. min.

RubberGard MAX FR 308241-0-0

1-675

IF: NC EF: A

Slope: ¼ʺ

Concrete Min. 2,500 psi Min. 2ʺ thick


boards ISO 95+ GL




SA-SB V-Force SB

Adhered at 12” o.c.: ISO Spray R



.045 mil.

RubberGard MAX PT


296332-0-0

1-690

IF: NC EF: A

Slope: ½ʺ Concrete Min. 2,500 psi Min. 2ʺ thick





Full Spray: ISO Spray R

1.04 gal/square


Permeable


.045 mil.


Single-Ply LVOC

135965-0-0

1-690

IF: NC EF: A

Slope: 2.5ʺ


135957-0-0

1-780

IF: NC EF: A

Slope: ¼ʺ Concrete

Min. 2,500 psi Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)


1.04 gal/square


.045 mil.


Single-Ply LVOC Single-Ply LVOC 1168

59191-0-0

1-780 IF: NC EF: A

Slope: 2.5ʺ


62452-0-0

Firestone RubberGard EPDM MAX/MAX FR - Fully Adhered Uplift Ratings Re-Roof Construction - Gypsum Deck – Adhered Insulation/Cover Board – Adhered Membrane

Uplift Deck Type


Cover Board and Insulation Attachment Membrane Membrane Attachment

RoofNav Number

1-90

IF: 1 EF: A

Slope: ½ʺ

Gypsum


DensDeck Securock



.045 mil.

RubberGard MAX PT



99650-0-0

1-90

IF: 1 EF: A

Slope: 4ʺ

Gypsum


DensDeck Securock



FR



32 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-90

IF: 1

EF: A

Slope: ½ʺ

Gypsum


DensDeck Securock

Insulation (Top Layer): 1.5ʺ-8ʺ thick, 4' x 4' boards


Resista Insulation (Bottom Layer): 1.5ʺ-4ʺ thick, 4' x 4' boards


Resista


ISO Twin Pack

.045 mil. min.

RubberGard MAX

.045 mil.

RubberGard MAX PT

BA-2004

Single-Ply LVOC


WBBA-P

99640-0-0

1-90

IF: 1

EF: A

Slope: 4ʺ

Gypsum


DensDeck Securock





Resista


ISO Twin Pack

.045 mil. min.

RubberGard MAX FR

BA-2004

Single-Ply LVOC


110304-0-0

1-90

IF: 1 EF: A

Slope: ¼ʺ

Gypsum




1.5ʺ-4ʺ thick, 4' x 4' boards ISO 95+ GL



ISO Stick

.045 mil. min.

RubberGard MAX

.045 mil.

RubberGard MAX PT

.045 mil. min.

RubberGard MAX FR

BA-2004

Single-Ply LVOC


WBBA-P

262899-0-0

Firestone EPDM – Platinum - Fully Adhered Uplift Ratings Concrete Deck - V-Force Vapor Barrier System – Adhered Insulation – Adhered Membrane


Insulation Cover Board and

Insulation Attachment Membrane

Membrane Attachment

RoofNav Number

1-75

IF: NC EF: A

Slope: ½ʺ



boards ISO 95+ GL




.090 mil. RubberGard

Platinum

.090 mil. RubberGard Platinum PT



371174-0-0

SFBA 384176-0-0

1-75

IF: NC EF: A

Slope: ¼ʺ






boards ISO 95+ GL





Platinum


BA-2004 SFBA

Single-Ply LVOC Single-Ply LVOC 1168

WBBA-P

371151-0-0

33 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type Cover Board and Insulation Cover Board and

Insulation Attachment

Membrane Membrane Attachment

RoofNav Number

1-90

IF: NC

EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick

Insulation: 1.5ʺ-36ʺ thick, 4' x 4' boards


Resista Vapor Barrier:

V-Force (Self Adhered)


ISO Spray R


Platinum


BA-2004

Single-Ply LVOC


WBBA-P

370560-0-0

SFBA 384154-0-0

1-255

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick






ISO Spray R


Platinum

.090 mil.

RubberGard Platinum PT

BA-2004

EPDM SFBA

Single-Ply LVOC


308435-0-0

1-315

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick




ISO Twin Pack


Platinum


BA-2004

Single-Ply LVOC


102219-0-0

1-465

IF: NC EF: A

Slope: 2ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick





ISO 95+ GL (Taper)


ISO Stick

Primed Deck: Concrete Primer,

Asphaltic Permeable


Platinum

.090 mil.


BA-2004


1-465

IF: NC EF: A

Slope: 3ʺ


Insulation: ½ʺ, 4' x 4' boards

DensDeck Securock

Adhered at 12” o.c.:

ISO Twin Pack


Platinum




1-525

IF: NC EF: A

Slope: ½ʺ






SA-SB V-Force SB


ISO Spray R ISO Twin Pack

ISO Stick


Platinum




1-525

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


ISOGARD HD 1ʺ-2.5ʺ, 4' x 4' boards, ISOGARD

HD COMPOSITE Insulation:




SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

SFBA

Single-Ply LVOC

WBBA-P

298272-0-0

34 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation Cover Board and


Membrane Attachment

RoofNav Number

1-525

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick








SA-SB V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC

297159-0-0

1-540

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL

ISO 95+ GL (Taper)


Primed Deck:


Permeable


Platinum


BA-2004


1-555

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


ISOGARD HD 1ʺ-2.5ʺ, 4' x 4’ boards


1ʺ-36ʺ thick, 4' x 4' boards ISO 95+ GL

ISO 95+ GL (Taper)


ISO Spray R

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

EPDM SFBA

Single-Ply LVOC


WBBA-P

308236-0-0

1-675

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick


boards ISO 95+ GL



SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC

296334-0-0

1-690

IF: NC EF: A

Slope: 3ʺ







1.04 gal/square


Platinum



126897-0-0

1-690

IF: NC EF: A

Slope: 1ʺ







1.04 gal/square


Platinum



62382-0-0

35 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone EPDM – Platinum - Fully Adhered Uplift Ratings Re-Roof Construction - Gypsum Deck – Adhered Insulation/Cover Board – Adhered Membrane

Uplift Deck Type




RoofNav Number

1-90

IF: 1 EF: A

Slope: 3ʺ

Gypsum


DensDeck Securock


ISO Twin Pack


Platinum




127015-0-0

1-90

IF: 1

EF: A

Slope: 3ʺ

Gypsum


DensDeck Securock





Resista


ISO Twin Pack

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC


WBBA-P

127014-0-0

1-90

IF: 1

EF: A

Slope: ¼ʺ

Gypsum







ISO Twin Pack

ISO Stick

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC


WBBA-P

262899-0-0

1-90

IF: 1

EF: A

Slope: ½ʺ

Gypsum


ISOGARD HD 1ʺ-8ʺ, 4' x 4' boards





ISO FIX II

ISO Spray R

ISO Twin Pack

ISO Stick

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC


WBBA-P

420488-0-0

36 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone EcoWhite EPDM – Fully Adhered Uplift Ratings Concrete Deck - V-Force Vapor Barrier System – Adhered Insulation – Adhered Membrane


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-450

IF: NC EF: A

Slope: ½ʺ




ISOGARD HD COMPOSITE Insulation:

4' x 4' boards (Top) ½ʺ - 4ʺ thick Taper Taper or Flat ISO 95+ GL

(2nd) 1.5ʺ-4ʺ thick (3rd) 1.5ʺ-4ʺ thick

(Bottom) 1.5ʺ-36ʺ thick Vapor Barrier:


SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.060 RubberGard EcoWhite


306708-0-0

1-465

IF: NC

EF: A

Slope: 1.5ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick





ISO 95+ GL (Taper)


ISO Stick .060 RubberGard

EcoWhite BA-2004


1-495

IF: NC

EF: A

Slope: 1ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick




ISO 95+ GL (Taper)

Adhered at 12” o.c.:

ISO Stick .060 RubberGard

EcoWhite

BA-2004

EPDM - SFBA

Single-Ply LVOC


231121-0-0

1-525

IF: NC EF: A

Slope: ½ʺ






SA-SB V-Force SB




BA-2004 Single-Ply LVOC Single-Ply LVOC

1168

297191-0-0

1-525

IF: NC EF: A

Slope: ½ʺ








SA-LVOC SA-SB

V-Force SB




BA-2004 SFBA

Single-Ply LVOC WBBA-P

298280-0-0

37 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type


Cover Board and Insulation Attachment Membrane

Membrane Attachment

RoofNav Number

1-525

IF: NC

EF: A

Slope: 1.5ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick







SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.060 RubberGard

EcoWhite

BA-2004

Single-Ply LVOC 297197-0-

0

1-540

IF: NC EF: A

Slope: ½ʺ


Insulation: 1.5ʺ-36ʺ thick, 4' x 4' ISO

95+ GL ISO 95+ GL (Taper)


.060 RubberGard

EcoWhite


231127-0-0

1-555

IF: NC EF: A

Slope: ½ʺ

Min. 2,500 psi

Min. 2ʺ thick







ISO Spray R

.060 RubberGard

EcoWhite

BA-2004

EPDM - SFBA

Single-Ply LVOC


WBBA-P

308243-0-0

1-675

IF: NC EF: A

Slope: ½ʺ

Concrete

Min. 2,500 psi

Min. 2ʺ thick



Resista Vapor Barrier:


SA-LVOC SA-SB

V-Force SB


ISO Spray R

ISO Twin Pack

ISO Stick

.060 RubberGard

EcoWhite

BA-2004

Single-Ply LVOC 296358-0-

0

Firestone EcoWhite EPDM - Fully Adhered Uplift Ratings Re-Roof Construction - Gypsum Deck – Adhered Insulation/Cover Board – Adhered Membrane

Uplift Deck Type




RoofNav Number

1-90

IF: 1 EF: A Slope: 1.5ʺ

Gypsum



Securock



.060 RubberGard

EcoWhite PT


256108-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Gypsum Insulation:

½ʺ, 4' x 4' boards ISOGARD HD



.060 RubberGard

EcoWhite PT



38 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:




RoofNav Number

1-90


Gypsum



Securock



.060 RubberGard

EcoWhite PT


256108-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Gypsum



ISOGARD HD Insulation (Top Layer):



Insulation (Bottom Layer): 1.5ʺ-8ʺ thick, 4' x 4' boards


Resista


ISO Stick


.060 RubberGard

EcoWhite PT


1168 WBBA-P

262840-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Gypsum





Resista


ISO Stick


.060 RubberGard

EcoWhite PT


1168 WBBA-P

262871-0-0

Firestone EPDM – LS-FR - Fully Adhered Uplift Ratings Concrete Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane




RoofNav Number

1-90

IF: NC EF: A

Slope: ½ʺ


Insulation: 2ʺ-12ʺ thick, 4' x 4' boards


Resista Vapor Barrier (Optional): V-Force (Self Adhered)

Primer SBS Torch

Insulation: 8 Heavy-Duty or Concrete Drive

Fasteners/Plates per 4' x 8' board


.060 mil. RubberGard LS-FR

PT


1168 WBBA - P

32595-0-0

39 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard EPDM LS-FR/Self Adhered (SA)– Fully Adhered Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board – Adhered Membrane




RoofNav Number

1-60

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Insulation: 1.5ʺ-12ʺ


Resista Optional:

4 or 6 mil Poly. V-Force (Self Adhered)

DensDeck

Insulation: 10 Heavy-Duty


Optional:

Self Adhered Loose Laid


.060 mil.

RubberGard LS-FR PT


1168 WBBA - P

32579-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:



.060 mil.

RubberGard LS-FR PT


1168 WBBA - P

32578-0-0

1-120

IF: 1 EF: A

Slope: ½ʺ

Steel 18-22 ga Wide Rib

33 ksi 72ʺ span



Optional: 4 or 6 mil Poly.

V-Force (Self Adhered) DensDeck



Optional:



.060 mil.

RubberGard LS-FR PT


1168

234811-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ


33 ksi 72” span







Optional:



.060 mil.

RubberGard LS-FR PT


1168

232549-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Insulation: 2ʺ-12ʺ


Resista Optional:


DensDeck



Optional:



.060 mil.

RubberGard LS-FR PT


1168 WBBA-P

32581-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ


33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:



.060 mil.

RubberGard LS-FR PT


1168

232557-0-0

1-225

IF: 1 EF: A

Slope: ½ʺ

Steel 22 ga

Wide Rib 33 ksi

62ʺ span 18-22 ga Wide Rib

80 ksi 72ʺ span



Resista Optional:


DensDeck



Optional: Self Adhered Loose Laid


.060 mil.

RubberGard LS-FR PT


1168

228247-0-0

40 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ ISOGARD HD



Resista Optional:

4 or 6 mil Poly. V-Force (Self

Adhered) DensDeck

Cover Board: 12 Heavy-Duty


Insulation: Loose Laid

Optional:



.060 mil.

RubberGard LS-FR PT

BA-2004 SFBA

Single-Ply LVOC Single-Ply LVOC

1168

285091-0-0

1-90

IF: 1 EF: A

Slope: 1ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ min.

DensDeck Securock

Insulation (Optional): 1.5ʺ -12ʺ


Optional: 4 or 6 mil Poly. V-Force (Self

Adhered) DensDeck



Insulation (Optional):

Loose Laid



.060 mil.

RubberGard LS-FR PT


1168 WBBA-P

34485-0-0

1-150

IF: 1 EF: A

Slope: 1ʺ


33 ksi 72ʺ span


DensDeck Securock

Insulation (Optional): 1.5ʺ-12ʺ


Resista Optional:


Adhered) DensDeck




Loose Laid



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard EPDM SA


1168

Self Adhered

200396-0-0

1-210

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18-20 ga

33 ksi 72ʺ span

22 ga 33 ksi

64ʺ span

18-22 ga 80 ksi

72” span


DensDeck Securock



Resista Optional:


Adhered) DensDeck




Loose Laid



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard EPDM SA


1168

Self Adhered

200397-0-0

1-90

IF: 1 EF: A

Slope: 1ʺ

Steel 18-20 ga

33 ksi 72ʺ span

Insulation: 2ʺ-4ʺ HailGard

Optional: 4 or 6 mil. Poly. V-Force (Self

Adhered) DensDeck

Insulation: 13 HD HailGard

Fasteners per 4' x 8' board


.060 mil. RubberGard LS-FR PT .045 mil. RubberGard

EPDM SA

BA-2004 SFBA


1168

Self Adhered

136340-0-0

41 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-150

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span

Cover Board: 2ʺ-4ʺ HailGard





Cover Board: 16 Heavy Duty


Insulation (Optional): Loose Laid Optional:



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard

EPDM SA


1168

Self Adhered

286011-0-0

1-300

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18ga/33ksi/70ʺ span 20ga/33ksi/60ʺ span 22ga/33ksi/54ʺ span 22-18ga/80ksi/72ʺ

span

Insulation:

2ʺ-4ʺ HailGard Optional:


DensDeck

Insulation: 32 Heavy Duty




.060 mil.

RubberGard LS-FR PT

BA-2004

213482-0-0

1-90

IF: 1 EF: A

Slope: 1ʺ

Steel 22-16 ga

33 ksi 72ʺ span

Cover Board: APA Rated OSB

Min. 0.438ʺ Max. 0.50ʺ Insulation: 1.5ʺ-12ʺ


Resista Optional:


DensDeck




Loose Laid



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard

EPDM SA

BA-2004 SFBA


1168 WBBA-P

Self Adhered

34524-0-0

1-150

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 22-18 ga

33 ksi 72” span









Loose Laid



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard

EPDM SA


1168

Self Adhered

77824-0-0

1-300

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18ga/33ksi/70ʺ span 20ga/33ksi/60ʺ span 22ga/33ksi/54ʺ span 22-18ga/80ksi/72ʺ

span









Loose Laid



.060 mil.

RubberGard LS-FR PT

.045 mil RubberGard

EPDM SA


1168

Self Adhered

213475-0-0

42 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard EPDM LS-FR/Self Adhered – Fully Adhered Uplift Ratings Re-Roof Construction – Steel Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-75

IF: 1

EF: A

Slope: ½ʺ

Steel

33 KSI

Insulation: LWIC

Insulation: 2ʺ-12ʺ thick, 4' x 4' boards



Primer SBS Torch

Insulation:

8 Heavy-Duty or Concrete Drive Fasteners/Plates

per

4' x 8' board

.045 mil min.

RubberGard LS-FR

.060 mil.

RubberGard LS-FR PT

BA-2004

Single-Ply LVOC


WBBA - P

213740-0-0

Firestone RubberGard EPDM MAX/MAX FR – Fully Adhered Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board – Adhered Membrane


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel 22-16 ga

33 ksi 72ʺ span








.045 mil min. RubberGard MAX

.045 mil.

RubberGard MAX PT


1168 WBBA-P

3027-0-0

1-60

IF: 1 EF: A

Slope: 2.5ʺ

Steel 22-16 ga

33 ksi 72ʺ span









FR


1168

32791-0-0

1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel 22-16 ga

33 ksi 72ʺ span









.045 mil.

RubberGard MAX PT


1168 WBBA-P

3008-0-0

1-90

IF: 1 EF: A

Slope: 2.5”

Steel 22-16 ga

33 ksi 72ʺ span







Optional:



FR


1168

32790-0-0

1-120

IF: 1 EF: A

Slope: ¼ʺ

Steel 22-18 ga

33 ksi 72ʺ span



Optional:




Optional:



.045 mil

RubberGard MAX PT


1168

234809-00

1-165

IF: 1 EF: A

Slope: ¼ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span










1168 232547-0-0

43 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-165

IF: 1 EF: A

Slope: 2.5”

Steel - WR 22-18 ga

33 ksi 72ʺ span









FR


1168 232554-0-0

1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel - WR 22-16 ga

33 ksi 72ʺ span



Resista Optional:




Optional:



.045 mil

RubberGard MAX PT


1168 WBBA-P

3029-0-0

1-165

IF: 1 EF: A

Slope: ¼ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span



Resista Optional:




Optional:




1168 232555-0-0

1-225

IF: 1 EF: A

Slope: ¼ʺ

Steel - WR 18ga/33ksi/72ʺ

span 20ga/33ksi/69ʺ


span 22-

18ga/80ksi/72ʺ span



Resista Optional:




Optional:



.045 mil

RubberGard MAX PT


1168

228245-0-0

1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel 22-16 ga

33 ksi 72ʺ span

Cover Board: 1ʺ, ISOGARD HD



Resista Optional:



Fasteners/Plates per 4' x 8' board Insulation: Loose Laid Optional:



.045 mil.

RubberGard MAX PT

BA-2004 SFBA


1168 WBBA-P

288355-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span


DensDeck Securock



Resista Optional:


DensDeck




Optional:



.045 mil

RubberGard MAX PT


1168 WBBA-P

33154-0-0

44 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span


DensDeck Securock



Resista Optional:


DensDeck




Optional:



.045 mil.

RubberGard MAX PT


1168 WBBA-P

33154-0-0

1-150

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span


DensDeck Securock



Resista Optional:


DensDeck




Optional:



.045 mil.

RubberGard MAX PT


1168

200399-0-0

1-210

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 20-


22ga/33ksi/64ʺspan 22-



DensDeck Securock

Insulation (Optional): 2ʺ-4ʺ ISO 95+ GL







Optional:



.045 mil.

RubberGard MAX PT


1168

200400-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 22-18 ga

33 ksi 72ʺ span








.045 mil.

RubberGard MAX PT

BA-2004 SFBA


1168

136339-0-0

1-150

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span










.045 mil.

RubberGard MAX PT


1168

286010-0-0

1-300

IF: 1 EF: A

Slope: ½ʺ




span 22-



Optional:


DensDeck



Optional:



.045 mil.

RubberGard MAX PT

BA-2004 213481-0-0

45 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-150

IF: 1 EF: A

Slope: 4”

Steel - WR 22-18 ga

33 ksi 72ʺ span










FR


1168

286016-0-0

1-300

IF: 1 EF: A

Slope: 4”

Steel - WR 18ga/33ksi/70″



span 22-







Optional:



FR BA-2004 213490-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72” span



ISO 95+ GLSO 95+ GL (Taper) Resista






Loose Laid



.045 mil.

RubberGard MAX PT

BA-2004 EPDM SFBA


1168 WBBA-P

33694-0-0

1-150

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span









Loose Laid



.045 mil.

RubberGard MAX PT


1168

77820-0-0

1-150

IF: 1 EF: A

Slope: 4ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span









Loose Laid



FR


1168

83398-0-0

1-300

IF: 1 EF: A

Slope: ½ʺ




span 22-










Loose Laid



.045 mil.

RubberGard MAX PT


1168 213470-0-0

46 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-300

IF: 1 EF: A

Slope: 4ʺ




span 22-










Loose Laid



FR


1168 213479-0-0

Firestone RubberGard EPDM MAX/MAX FR – Fully Adhered Uplift Ratings Re-Roof Construction – Steel Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane


Insulation


Attachment Membrane

Membrane Attachment

RoofNav Number

1-75

IF: 1 EF: A

Slope: ¼ʺ Steel 33 ksi

Insulation: LWIC

Insulation: 1ʺ-8ʺ ISO 95+ GL



Fasteners/Plates per 4'x8' board


.045 mil.

RubberGard MAX PT


1168 WBBA-P

213739-0-0

1-75

IF: 1 EF: A

Slope: 2.5ʺ



1168

213743-0-0

1-90

IF: 1 EF: A


Insulation: 1ʺ ISO 95+ GL





.045 mil.

RubberGard MAX PT


1168 WBBA-P

310170-0-0

1-90

IF: 1 EF: A

Slope: 2.5ʺ



1168

310192-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ Steel 33 ksi

Cover Board: ½ʺ min. Securock



Resista Optional:


DensDeck




Optional:



.045 mil.

RubberGard MAX PT


1168 WBBA-P

372669-0-0

1-90

IF: 1 EF: A

Slope: 4ʺ



1168

372675-0-0

47 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard EPDM MAX/MAX FR – Fully Adhered Uplift Ratings Re-Cover Construction – Steel Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane

Uplift Deck Type


Cover Board and Insulation Attachment


RoofNav Number

1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel 33 ksi

Cover Board: ½ʺ, ISOGARD HD

Insulation: ½ʺ ISO 95+ GL

Resista

Cover Board: 12 Heavy-Duty Fasteners/Plates

per 4'x8' board Insulation: Loose Laid


.045 mil. RubberGard MAX PT



1168

233351-0-0

1-90


Steel 33 ksi

Cover Board: ½ʺ-1ʺ

Structodek HD Fiberboard Insulation: ½ʺ -1.5ʺ


Resista


per 4'x8' board






1168

45188-0-0

1-120

IF: 1 EF: A



Insulation:

½ʺ ISO 95+ GL


per 4'x8' board






1168 WBBA-P

288115-0-0

1-120




1168

288149-0-0

FirestoneRubberGardEPDMMAX/MAXFR‐FullyAdheredUpliftRatingsConcreteDeck–MechanicallyAttachedInsulation–AdheredInsulation/CoverBoard–AdheredMembrane

Uplift Deck Type




RoofNav Number

1-75

IF: 1 EF: A Slope:

¼ʺ Concrete

Min. 2,500 psi Min. 2ʺ thick

Cover Board: 4'x4' boards

½ʺ, ISOGARD HD 1ʺ-2.5ʺ, ISOGARD HD

Composite Insulation:

2ʺ-4ʺ ISO 95+ GL


Optional: V-Force (Self Adhered)

SBS Torch

Cover Board: Adhered at 12ʺ o.c. beads

ISO Fix ISO Spray R

ISO Twin Pack ISO Stick Insulation:

8 Concrete Drive or Heavy-Duty Fasteners/Plates per 4'x8' board


w/ Primer Torched


.045 mil.

RubberGard MAX PT

BA-2004 EPDM SFBA

Single-Ply LVOC


WBBA-P

319374-0-0

1-75


.045 mil. min.

RubberGard MAX FR

319397-0-0

1-90

IF: NC EF: A Slope:

¼ʺ Concrete

Min. 2,500 psi

Min. 2ʺ thick



Composite Insulation:

1.5ʺ-4ʺ ISO 95+ GL



SBS Torch

Cover Board: Adhered at 12” o.c. beads

ISO Spray R Insulation:

16 Concrete Drive or Heavy-Duty Fasteners/Plates per 4’x8’

board Optional:

V-Force (Self Adhered) w/ Primer Torched


.045 mil.

RubberGard MAX PT

BA-2004

EPDM SFBA

Single-Ply LVOC


WBBA-P

307728-0-0

1-90

IF: NC EF: A Slope: 2.5ʺ


307735-0-0

48 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type


Cover Board and Insulation Attachment Membrane

Membrane Attachment

RoofNav Number

1-90

IF: NC EF: A

Slope: ¼ʺ Concrete Min. 2,500

psi Min. 2ʺ thick



Composite 2 Layers Insulation:

1.5ʺ-4ʺ ISO 95+ GL



SBS Torch


ISO Spray R Insulation:

16 Concrete Drive or Heavy-Duty Fasteners/Plates per 4'x8'

board Optional:



.045 mil.


EPDM SFBA Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA-P

307740-0-0

1-90

IF: NC EF: A

Slope: 2.5ʺ


307752-0-0

1-120

IF: NC EF: A

Slope: ½ʺ

Concrete Min. 2,500

psi Min. 2ʺ thick

Cover Board: ½ʺ min. 4'x4' boards

DensDeck Prime Securock Insulation:

2ʺ-4ʺ ISO 95+ GL

ISO 95+ GL (Taper) Insulation (Optional):

2ʺ-8ʺ, ISO 95+ GL ½ʺ-8” ISO 95+ GL

(Taper) ½ʺ-8ʺ Resista (Taper)

Vapor Retarder (Optional):

4 or 6 mil Poly.

Cover Board: Adhered at 6” o.c. beads

ISO Fix II ISO Twin Pack

ISO Stick Insulation:


board Insulation (Optional):

Loose Laid Vapor Retarder Optional):

Loose Laid


.045 mil.


EPDM SFBA Single-Ply

LVOC Single-Ply

LVOC 1168

340791-0-0

1-120

IF: NC EF: A

Slope: 4ʺ


340797-0-0

1-120

IF: NC EF: A

Slope: ¼ʺ Concrete Min. 2,500

psi Min. 2ʺ thick



Composite 2 Layers Insulation:

2ʺ-12ʺ ISO 95+ GL

ISO 95+ GL (Taper) Optional:

V-Force (Self Adhered) SBS Torch


ISO Fix II ISO Spray R

ISO Twin Pack ISO Stick Insulation:


board Optional:



.045 mil.

RubberGard MAX PT BA-2004 EPDM SFBA

Single-Ply LVOC

WBBA-P

320253-0-0

1-120

IF: NC

EF: A

Slope: 2.5ʺ

.045 mil. min. RubberGard MAX FR 320259-0-0

Firestone RubberGard EPDM Platinum – Fully Adhered Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board – Adhered Membrane

Uplift Deck Type




RoofNav Number

1-60

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


Adhered) DensDeck

Insulation: 10 Heavy-Duty Fasteners/Plates

per 4'x8' board


.090 mil. RubberGard Platinum

.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA - P

32579-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


Adhered) DensDeck


per 4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA - P

32578-0-0

49 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type




RoofNav Number

1-120

IF: 1 EF: A

Slope: ½ʺ


33 ksi 72ʺ span






per 4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168

234811-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ


33 ksi 72” span






per 4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC 1168

232549-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck

Insulation: 8 Heavy-Duty Fasteners/Plates per

4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA-P

32581-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ


33 ksi 72ʺ span



Resista Optional:


DensDeck


per 4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168

232557-0-0

1-225

IF: 1 EF: A

Slope: ½ʺ

Steel 22 ga

Wide Rib 33 ksi

62ʺ span 18-22 ga Wide Rib

80 ksi 72ʺ span



Resista Optional:


DensDeck


per 4'x8' board



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168

228247-0-0

1-90

IF: 1 EF: A

Slope: 3ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ DensDeck or

Securock Insulation: 1.5ʺ-12ʺ


Resista Optional:



per 4'x8' board


Optional:



.090 mil.


BA-2004 Single-Ply

LVOC Single-Ply

LVOC 1168 WBBA-P

126884-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72” span

Cover Board: ½ʺ ISOGARD HD



Resista Optional:



per 4'x8' board Insulation: Loose Laid Optional:



.090 mil.


BA-2004 SFBA

Single-Ply LVOC


285091-0-0

50 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:

Uplift Deck Type

Cover Board and Insulation Cover Board and


Membrane Attachment

RoofNav Number

1-150

IF: 1 EF: A

Slope: 3ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ DensDeck or Securock



Resista Optional:




Insulation: Loose Laid Optional:



.090 mil.



1168

200406-0-0

1-210

IF: 1 EF: A

Slope: 3ʺ

Steel – WR 20-



22-18ga/80ksi/

72ʺ span

Cover Board: ½ʺ DensDeck or Securock



Resista Optional:







.090 mil.



1168

200407-0-0

1-90

IF: 1 EF: A

Slope: 2ʺ

Steel 18-20 ga

33 ksi 72ʺ span




Insulation: 13 HD HailGard

Fasteners per 4'x8' board


.090 mil.


BA-2004 SFBA


1168

136343-0-0

1-150

IF: 1 EF: A

Slope: 2ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span








Optional:



.090 mil.



1168

286014-0-0

1-300

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18ga/33ksi/

70ʺ span 20ga/33ksi/

60ʺ span 22ga/33ksi/

54ʺ span 22-

8ga/80ksi/72ʺ span


Optional:


DensDeck



Optional:



.090 mil.


BA-2004

213482-0-0

1-90

IF: 1 EF: A

Slope: 2ʺ

Steel 16-22 ga

33 ksi 72ʺ span


Min. 0.438ʺ - Max. 0.50ʺ Insulation: 1.5ʺ-12ʺ


Resista Optional:


DensDeck




Optional:



.090 mil.


BA-2004 SFBA


1168 WBBA-P

127565-0-0

1-150

IF: 1 EF: A

Slope: 2ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span







Fasteners/Plates per 4’x8’ board


Optional:



.090 mil.



1168

127571-0-0

51 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



Membrane Attachment

RoofNav Number

1-300

IF: 1 EF: A

Slope: ½ʺ




span 22-



Min. 0.438” - Max. 0.50” Insulation: 1.5ʺ-12ʺ







Optional:



.090 mil.


BA-2004 Single-Ply

LVOC 1168

213471-0-0

Firestone RubberGard EPDM Platinum – Fully Adhered Uplift Ratings Re-Roof Construction – Steel Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane



Membrane Attachment

RoofNav Number

1-75

IF: 1

EF: A

Slope: ½ʺ

Steel

33 KSI

Insulation: LWIC

Insulation: 2ʺ-12ʺ thick, 4'x4' boards



Primer SBS Torch

Insulation:

8 Heavy-Duty Fasteners/Plates per 4'x8'

board

.090 mil.

RubberGard Platinum

.090 mil.


BA-2004

Single-Ply LVOC


WBBA - P

213740-0-0

Firestone RubberGard EPDM Platinum - Fully Adhered Uplift Ratings Concrete Deck – Mechanically Attached Insulation/Cover Board – Adhered Membrane

Uplift Deck Type Cover Board and Insulation Cover Board and Insulation

Attachment Membrane

Membrane Attachment

RoofNav Number

1-90

IF: NC EF: A

Slope: ¼ʺ





Resista

Insulation: 18 Heavy-Duty or Concrete Drive Fasteners/Plates per

4'x8' board


.090 mil.



1168 WBBA - P

288348-0-0

1-90

IF: NC EF: A

Slope: 3ʺ


Cover Board: ¼ʺ, DensDeck ½ʺ, Securock



Resista


4'x8' board


.090 mil.



1168 WBBA - P

265632-0-0

1-120

IF: NC EF: A Slope: 1.5ʺ






4'x8' board


.090 mil.



1168 WBBA - P

288146-0-0

52 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone EcoWhite – Fully Adhered Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board

Uplift Deck Type Cover Board and Insulation Cover Board and Insulation

Attachment Membrane

Membrane Attachment

RoofNav Number

1-60

IF: 1 EF: A

Slope: ½ʺ

Steel 18-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:



.060 RubberGard EcoWhite PT


1168 WBBA-P

229856-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:





1168 WBBA-P

229854-0-0

1-120

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span







Optional:




1168 WBBA-P

255161-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span







Optional:




1168

255155-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:





1168 WBBA-P

229858-0-0

1-165

IF: 1 EF: A

Slope: ½ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span



Resista Optional:


DensDeck



Optional:




1168

255156-0-0

1-225

IF: 1 EF: A

Slope: ½ʺ




span 22-18ga/80ksi/72ʺ

span










1168

229911-0-0

53 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



Membrane Attachment

RoofNav Number

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 16-22 ga

33 ksi 72ʺ span




Resista Optional:


DensDeck




Optional:




BA-2004 SFBA


1168 WBBA-P

289472-0-0

1-90

IF: 1 EF: A

Slope: 1.5ʺ

Steel 16-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ, DensDeck or Securock



Resista Optional:


DensDeck




Optional:





1168 WBBA-P

230168-0-0

1-150

IF: 1 EF: A

Slope: 1.5ʺ

Steel 18-22 ga

33 ksi 72ʺ span

Cover Board: ½ʺ, DensDeck Prime or








Optional:




1168

230208-0-0

1-210

IF: 1 EF: A

Slope: 1.5ʺ

Steel - WR 20-18ga/33ksi/72ʺ



span

Cover Board: ½ʺ, DensDeck Prime or








Optional:




1168

230209-0-0

1-90

IF: 1 EF: A

Slope: 1ʺ

Steel 18-20 ga

33 ksi 72ʺ span




Insulation: 13 HD HailGard Fasteners

per 4'x8' board



BA-2004 SFBA


1168

229884-0-0

1-150

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 18-22 ga

33 ksi 72ʺ span












1168

286017-0-0

54 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



Membrane Attachment

RoofNav Number

1-300

IF: 1 EF: A

Slope: 1ʺ





span







.060 RubberGard EcoWhite BA-2004 229886-0-0

1-90

IF: 1 EF: A

Slope: 1ʺ

Steel 22-16 ga

33 ksi 72ʺ span




Resista 1.4-4ʺ ISO 95+ Composite






Optional:




BA-2004 SFBA


1168 WBBA-P

229930-0-0

1-150

IF: 1 EF: A

Slope: 1ʺ

Steel - WR 22-18 ga

33 ksi 72ʺ span









Optional:




1168

229931-0-0

1-300

IF: 1 EF: A

Slope: 1ʺ





span









Optional:


.060 RubberGard EcoWhite BA-2004


229955-0-0

Firestone – Fully Adhered Uplift Ratings Re-Cover Construction – Treated Wood Deck – Mechanically Attached Insulation/Cover Board

Uplift Deck Type



Membrane Membrane Attachment RoofNav Number

1-90 IF: 1 EF: A

Slope: ½ʺ

Treated Wood

Insulation: 1ʺ ISO 95+ GL


Insulation: 16 All-Purpose or

Heavy Duty Fasteners/Plates per 4'x8' board


.060 mil. RubberGard LS-FR PT



326810-0-0

1-90 IF: 1 EF: A

Slope: ¼ʺ





326806-0-0

1-90 IF: 1 EF: A

Slope: 2.5ʺ




1-90 IF: 1 EF: A Slope:

1/2”




326814-0-0

55 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard LS-FR Mechanically Attached Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board

Uplift Deck Type Cover Board/Insulation Membrane and Row Spacing

Membrane Attachment RoofNav Number

1-60

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span

Insulation: ISO 95+ GL – 1.5ʺ-12ʺ, 4'x8' boards

ISO 95+ GL (Taper) – 1.5ʺ-12ʺ, 4'x8' boards Resista – 1.5ʺ-12ʺ, 4'x8' boards

DensDeck – ¼ʺ min. Securock – ¼ʺ min.

Attachment: Pre-securement Vapor Retarder (Optional):

4-6 min. poly V-Force (Self-Adhered) over DensDeck

BaseGard SA (Self-Adhered) over DensDeck

.045 mil. min. RubberGard LS-

FR

84ʺ rows at 6ʺ o.c. HD Fasteners and

Firestone Metal or Polymer Batten

78504-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span



DensDeck – ¼ʺ min., 4’x8’ boards Securock – ¼ʺ min., 4’x8’ boards




.045 mil. min. RubberGard LS-

FR 78ʺ Max Width


Firestone Metal Batten 45679-0-0

Firestone RubberGard MAX Mechanically Attached Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board



1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel: 22-




Insulation: ISO 95+ GL – 1ʺ-12ʺ, 4'x8' boards

ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards ISO 95+ Composite – 1ʺ-1.5ʺ, 4'x8' boards

Resista – 1ʺ-12ʺ, 4'x8' boards Structodek – 1ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets

114ʺ rows at 6ʺ o.c. HD Fasteners/Plates

10931-0-0

1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel: 22-




Cover Board: ISOGARD HD – ½ʺ, 4'x8' boards

Attachment: Pre-securement Insulation:

ISO 95+ GL – 1ʺ-12ʺ, 4'x8' boards ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards

Resista – 1ʺ-12ʺ, 4'x8' boards Attachment: Loose Laid

Vapor Retarder (Optional): 4-6 min. poly

V-Force (Self-Adhered) over DensDeck BaseGard SA (Self-Adhered) over DensDeck


10' Sheets

114ʺ rows at 6ʺ o.c. HD Fasteners/Plates

386732-0-0

1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel: 20ga/33ksi/7

2ʺ span 22ga/33ksi/6

0ʺ span


ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards ISO 95+ Composite – 1.4ʺ-4ʺ, 4'x8' boards

Resista – 1ʺ-12ʺ, 4'x8' boards Structodek – 1ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets


Firestone Polymer Batten 334034-0-0

56 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel: 20ga/33ksi/7

2ʺ span 22ga/33ksi/6

0ʺ span








10' Sheets



1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel: 18-







Resista – 1ʺ-12ʺ, 4'x8' boards Structodek – 1ʺ min., 4'x8' boards FiberTop B – ½ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10′ Sheets



1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel: 18-












10' Sheets



1-120

IF: 1 EF: A

Slope: ¼ʺ

Steel: Wide Rib 20-






Attachment: Loose Laid Vapor Retarder (Optional):




10' Sheets

114ʺ rows at 6ʺ o.c. HD Plus Fasteners and

Firestone Polymer Batten Additional:

Mid-span attachment at 12ʺ o.c. stripped in with cover

strip.

386950-0-0

1-120

IF: 1 EF: A

Slope: ¼ʺ

Steel: Wide Rib 20-





Resista – 1ʺ-12ʺ, 4'x8' boards Structodek – 1” min., 4'x8' boards FiberTop B – ½ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets



Mid-span attachment at 12ʺ o.c. stripped in with cover

strip.

128862-0-0

57 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard MAX FR (Fire Retardant) Mechanically Attached Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board



1-60

IF: 1 EF: A

Slope: 2ʺ

Steel: 20-





ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards Resista – 1ʺ-12ʺ, 4'x8' boards Attachment: Pre-securement Vapor Retarder (Optional):




10' Sheets

114ʺ rows at 6ʺ o.c. HD Fasteners and Firestone V-Plates

386470-0-0

1-60

IF: 1 EF: A

Slope: 3ʺ

Steel: 20-




Insulation: Structodek – 1ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets


48124-0-0

1-60

IF: 1 EF: A

Slope: 2ʺ

Steel: 20-






Resista – 1ʺ-12ʺ, 4'x8' boards Attachment: Pre-securement Vapor Retarder (Optional):




10' Sheets


47996-0-0

1-90

IF: 1 EF: A

Slope: 2ʺ

Steel: 22ga/80ksi/72ʺ

span








10' Sheets



Mid-span attachment at 12ʺ o.c. stripped in with cover strip.

386601-0-0

1-90

IF: 1 EF: A

Slope: 2ʺ


span


ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards ISO 95+ Composite – 1.4”-4”, 4’x8’ boards





10' Sheets




330918-0-0

1-90

IF: 1 EF: A

Slope: 3ʺ


span

Insulation: Structodek – ½ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets




330922-0-0

58 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-90

IF: 1 EF: A

Slope: 3ʺ


span

Cover Board: Structodek – 1ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards


ISO 95+ GL – 1.5ʺ-12ʺ, 4'x8' boards ISO 95+ GL (Taper) – 1.5ʺ-12”, 4'x4' boards ISO 95+ Composite – 1.4ʺ-4ʺ, 4'x8' boards

Resista – 1.5ʺ-12ʺ, 4'x8' boards Attachment: Loose Laid




10' Sheets




330925-0-0

1-120

IF: 1 EF: A

Slope: 2ʺ

Steel: Wide Rib 20-










10' Sheets




386569-0-0

1-120

IF: 1 EF: A

Slope: 3ʺ

Steel: Wide Rib 20-



Cover Board: Structodek – ½ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards


ISO 95+ GL – 1.5ʺ-12ʺ, 4'x8' boards ISO 95+ GL (Taper) – 1.5ʺ-12ʺ, 4'x4' boards ISO 95+ Composite – 1.4ʺ-4ʺ, 4'x8' boards





10' Sheets




128968-0-0

1-120

IF: 1 EF: A

Slope: 2ʺ

Steel: Wide Rib 20-









10' Sheets




128880-0-0

1-120

IF: 1 EF: A

Slope: 3ʺ

Steel: Wide Rib 20-



Cover Board: Structodek – 1” min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





10' Sheets




128882-0-0

59 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Firestone RubberGard MAX – QuickSeam R.MA. - Mechanically Attached Uplift Ratings SteelDeck,NewConstruction–MechanicallyAttachedInsulation/CoverBoard



1-60

IF: 1 EF: A

Slope: ¼ʺ

Steel: 20-






Resista – 1ʺ-12ʺ, 4'x8' boards Structodek – ½ʺ, 4'x8' boards

DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards

FiberTop B – ½ʺ, 4'x8' boards Attachment: Pre-securement Vapor Retarder (Optional):




QuickSeam R.M.A. Strip Polymer Batten

114ʺ rows, 6ʺ o.c.

QuickSeam R.M.A. Strip Heavy Duty Fasteners/Plates


79883-0-0

1-60

IF: 1 EF: A

Slope: ½ʺ

Steel: 20-




Insulation: Structodek – ½ʺ, 4'x8' boards










80045-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel: 18-



20g/80ksi/72ʺ span












80061-0-0

1-90

IF: 1 EF: A

Slope: ¼ʺ

Steel: 18-



20g/80ksi/72” span














79891-0-0

1-105

IF: 1 EF: A

Slope: ¼ʺ

Steel: Wide Rib 18ga/33ksi/54ʺ

span 20-












114” rows, 6” o.c.



79900-0-0

60 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-105

IF: 1 EF: A

Slope: ½ʺ


span 20-









QuickSeam R.M.A. Strip Heavy Duty Fasteners/ V-

Plates 114ʺ rows, 6ʺ o.c.

80183-0-0

1-105

IF: 1 EF: A

Slope: ½ʺ


span 20-





ISO 95+ GL – 1ʺ-12ʺ, 4'x8' boards ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x4' boards ISO 95+ Composite – 1.4ʺ-4ʺ, 4'x8' boards





QuickSeam R.M.A. Strip Heavy Duty Fasteners/ V-

Plates 114ʺ rows, 6ʺ o.c.

80187-0-0

1-105

IF: 1 EF: A

Slope: ¼ʺ


span 20-














386867-0-0

Firestone RubberGard MAX FR (Fire Retardant) – QuickSeam R.MA. – Mechanically Attached Uplift Ratings SteelDeck,NewConstruction–MechanicallyAttachedInsulation/CoverBoard



1-60

IF: 1 EF: A

Slope: 2ʺ

Steel: 20-16ga/33ksi/72ʺ span

22ga/33ksi/60ʺ span 22ga/80ksi/72ʺ span






.045 mil. min. RubberGard

MAX FR


114ʺ rows, 6ʺ o.c. QuickSeam R.M.A. Strip

Heavy Duty Fasteners/ V-Plates 114ʺ rows, 6ʺ o.c.



80362-0-0

1-60

IF: 1 EF: A

Slope: 3ʺ


22ga/33ksi/60ʺ span 22ga/80ksi/72ʺ span








MAX FR



QuickSeam R.M.A. Strip Heavy Duty Fasteners/ V-Plates




80398-0-0

61 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-90

IF: 1 EF: A

Slope: 2ʺ


20ga/33ksi/48ʺ span 20g/80ksi/72ʺ span








MAX FR






80346-0-0

1-90

IF: 1 EF: A

Slope: 2ʺ











MAX FR






386524-0-0

1-90

IF: 1 EF: A

Slope: 3”

Steel: 18-16ga/33ksi/72” span

20ga/33ksi/48” span 20g/80ksi/72” span

22ga/80ksi/72” span

Insulation: Structodek – ½ʺ min., 4’x8’ boards DensDeck – ¼ʺ min., 4’x8’ boards Securock – ¼ʺ min., 4’x8’ boards





MAX FR






80410-0-0

1-90

IF: 1 EF: A

Slope: 3ʺ




Cover Board: Structodek – ½ʺ min., 4’x8’ boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards







MAX FR







80414-0-0

1-105

IF: 1 EF: A

Slope: 3ʺ

Steel: Wide Rib 18ga/33ksi/54ʺ span

20-18ga/80ksi/72ʺ span 22ga/80ksi/54ʺ span

Insulation: Structodek – ½ʺ min., 4'x8' boards DensDeck – ¼ʺ min., 4'x8' boards Securock – ¼ʺ min., 4'x8' boards





MAX FR






80426-0-0

1-105

IF: 1 EF: A

Slope: 3ʺ










MAX FR







80430-0-0

62 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-105

IF: 1 EF: A

Slope: 2ʺ










MAX FR






386532-0-0

1-105

IF: 1 EF: A

Slope: 2ʺ









MAX FR






80354-0-0

Firestone RubberGard Platinum Mechanically Attached Uplift Ratings Steel Deck, New Construction – Mechanically Attached Insulation/Cover Board



1-60

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span



DensDeck – ¼ʺ min. – 4'x8' boards Securock – ¼ʺ min. – 4'x8' boards





Platinum



Firestone Metal or Polymer Batten Strip and HD Fasteners

78504-0-0

1-60

IF: 1 EF: A

Slope: 1.5”

Steel 22-16 ga

33 ksi 72ʺ span



ISO 95+ Composite – 1.4ʺ-4ʺ, 4'x8' boards Structodek – ½ʺ min. – 4'x8' boards DensDeck – ¼ʺ min. – 4'x8' boards Securock – ¼ʺ min. – 4'x8' boards





Platinum



Firestone Metal or Polymer Batten Strip and HD Fasteners

125220-0-0

1-60

IF: 1 EF: A

Slope: 1.5ʺ

Steel 22-16 ga

33 ksi 72ʺ span


ISO 95+ GL (Taper) – 1ʺ-12ʺ, 4'x8' boards Resista – 1ʺ-12ʺ, 4'x8' boards Attachment: Pre-securement


Platinum .090 mil.


84ʺ rows at 6ʺ o.c. QuickSeam R.M.A. Strip w/

Metal or Polymer Batten Strip and HD Fasteners

181910-0-0

1-60

IF: 1 EF: A

Slope: 1.5ʺ

Steel 22-16 ga

33 ksi 72ʺ span




Platinum .090 mil.


96ʺ rows at 12ʺ o.c. QuickSeam R.M.A. Strip w/ Metal Batten Strip and HD

Fasteners

181927-0-0

63 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Continued:



1-60

IF: 1 EF: A

Slope: 1.5”

Steel 22-16 ga

33 ksi 72ʺ span




Platinum .090 mil.



Firestone Metal Batten Strip and HD Fasteners

196547-0-0

1-60

IF: 1 EF: A

Slope: 1.5”

Steel 20ga/33ksi/72ʺ span 22ga/33ksi/60ʺ span


ISO 95+ GL (Taper) – 1.5”-12”, 4’x8’ boards Resista – 1.5”-12”, 4’x8’ boards

Attachment: Pre-securement


Platinum .090 mil.



Firestone Poly Batten Strip and HD Plus Fasteners

335012-0-0

1-75

IF: 1 EF: A

Slope: ½ʺ

Steel 22-16 ga

33 ksi 72ʺ span




Platinum .090 mil.


72ʺ rows at 12ʺ o.c. QuickSeam R.M.A. Strip w/

Metal or Polymer Batten Strip and HD Fasteners

181941-0-0

1-90

IF: 1 EF: A

Slope: ½ʺ

Steel 18-16ga/33ksi/72ʺ

span 20ga/33ksi/48” span 20ga/80ksi/72ʺ span 22ga/80ksi/72ʺ span


ISO 95+ GL (Taper) – 1.5”-12”, 4’x8’ boards Resista – 1.5ʺ-12ʺ, 4'x8' boards





Platinum



Firestone Poly Batten Strip and HD Plus Fasteners

230418-0-0

Factory Mutual Ballast Guidelines

Stone Ballast ASTM D448 — Standard Size No. 3 for Coarse Aggregate (nominal 1 to 2 in. [25 to 50 mm] diameter). This standard permits

amounts (by weight percent) to pass through the square sieve openings as shown in Table 6.

Table 6. Gradation for No. 3 Stone

Size Number Nominal Size in. (mm) Sieve Opening in. (mm)

2 ½ (63) 2 (50) 1 ½ (38) 1 (25) ¾ (19) ½ (13)

3 1 to 2 (25 - 50) 100 90 to 100 35 to 70 0 to 15 -- 0 to 5

Per FM Global Loss Prevention Data Sheet 1-29: Please refer to this LPDS for full FM requirements as they relate to ballasted roofing systems. 2.2.10.17.1 FM Approvals does not Approve ballasted systems. If a ballasted system is to be used, select components that

are FM Approved for use together as shown in a specific RoofNav assembly. In lieu of fasteners or adhesives used to secure above-deck components, use ballast in accordance with this data sheet to provide wind resistance.

- Do not use any aggregate surfacing, such as pea gravel or slag surfacing or crushed stone, in (a) regions prone to tropical cyclones and where the wind speed per D.S. 1-28 is ≥ 100 mph (≥ 45 m/s), or (b) in other regions on buildings taller than that defined in Table 7. Where added protection for the roof cover is needed, such as near major fire walls, concrete paver blocks can be used.

- Do not use stone-ballasted roofs on the following: A. Buildings taller than 150' (46 m) B. In areas prone to tropical cyclones C. In areas with design wind speeds ≥ 100 mph (45 m/s) (see Data Sheet 1-28, Wind Design) D. Beyond the acceptable limits shown in Tables 12 and 13

NOTE: These limitations do not apply to paver ballasted systems.

64 | P a g e

D e c e m b e r 1 3 , 2 0 1 7

Perimeter and Corners on ballast roof: - For ballast application only, the roof perimeter and corner dimensions should be equal to at least 40% of the mean roof

height, but not less than 8.5' (2.6 m) or 4% of the lesser plan dimension. - Have the load capacity of the roof verified by a registered civil or structural engineer. The structure must be capable

of supporting the dead weight of the roof system and ballast considering other gravity loads, without creating or aggravating a ponding problem.

- Ensure the roof slope is no more than 10°, 2ʺ/ft (167 mm/m). Ballast Weight:

NOTE:

1. For all tables, to convert to kg/m², multiply by 4.88. 2. Uplift pressure is that determined from Data Sheet 1-28, Wind Design, and is not factored. 3. Paver Weight requirements can be found in LPDS 1-29.

Date post:	01-Apr-2018
Category:	Documents
Upload:	trancong
View:	213 times
Download:	0 times

RubberGard™ EPDM Roof Systems Code Approval...

Documents