This manual may not be reproduced in whole or in part without the express writtenpermission of Sturm, Ruger & Co., Inc.
For Service on This Model Please Call:(336) 949-5200 (See p. 32)
THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BETRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED
OR PRESENTED TO ANOTHER PERSON
www.ruger.comMKIV 3/17 R2
S
READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM
– Rugged, Reliable Firearms® –
3
State-By-State WarningsCertain states require by law that their own specified warningnotices in larger-than-normal type be conspicuously included bythe manufacturer, distributor or retailer with firearms sold in thatstate. Sturm, Ruger & Co., Inc. sells its products in compliancewith applicable laws and regulations. Because our products maybe sold in these states, we include the following:
California:
Connecticut:“UNLAWFUL STORAGE OF A LOADED FIREARM MAYRESULT IN IMPRISONMENT OR FINE.”
Florida:“IT IS UNLAWFUL, AND PUNISHABLE BYIMPRISONMENT AND FINE, FOR ANY ADULT TOSTORE OR LEAVE A FIREARM IN ANY PLACE WITHINTHE REACH OR EASY ACCESS OF A MINOR UNDER 18YEARS OF AGE OR TO KNOWINGLY SELL OROTHERWISE TRANSFER OWNERSHIP OR POSSESSIONOF A FIREARM TO A MINOR OR A PERSON OFUNSOUND MIND.”
WARNING
“Children are attracted to andcan operate firearms that cancause severe injuries or death.Prevent child access by alwayskeeping guns locked away andunloaded when not in use. If youkeep a loaded firearm where achild obtains and improperly usesit, you may be fined or sent toprison.”
ADVERTENCIA“A los niños los atraen las armasde fuego y las pueden hacerfuncionar. Ellos pueden causarseslesions graves y la muerte. Eviteque los niños tengan accesso a lasarmas de fuego guardándolassiempre con llave y descargadascuando no las esté utilizando. Siusted tiene un arma de fuegocargada en un lugar en que unniño tiene acceso a ella y la usaindebidamente, le pueden dar unamulta o enviarlo a la carcel.”
Maine:“ENDANGERING THE WELFARE OF A CHILD IS ACRIME. IF YOU LEAVE A FIREARM AND AMMUNITIONWITHIN EASY ACCESS OF A CHILD, YOU MAY BESUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEPFIREARMS AND AMMUNITION SEPARATE. KEEPFIREARMS AND AMMUNITION LOCKED UP. USETRIGGER LOCKS.”
Maryland:“WARNING: Children can operate firearms which may causedeath or serious injury. It is a crime to store or leave a loadedfirearm in any location where an individual knew or shouldhave known that an unsupervised minor would gain access tothe firearm. Store your firearm responsibly!”
Massachusetts:“WARNING FROM THE MASSACHUSETTS ATTORNEYGENERAL: This handgun is not equipped with a device thatfully blocks use by unauthorized users. More than 200,000firearms like this one are stolen from their owners every yearin the United States. In addition, there are more than athousand suicides each year by younger children andteenagers who get access to firearms. Hundreds more die fromaccidental discharge. It is likely that many more childrensustain serious wounds, or inflict such wounds accidentally onothers. In order to limit the chance of such misuse, it isimperative that you keep this weapon locked in a secure placeand take other steps necessary to limit the possibility of theftor accident. Failure to take reasonable preventive steps mayresult in innocent lives being lost, and in some circumstancesmay result in your liability for these deaths.”“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM,RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACEUNLESS THAT WEAPON IS EQUIPPED WITH ATAMPER-RESISTANT SAFETY DEVICE OR IS STOREDOR KEPT IN A SECURELY LOCKED CONTAINER.”
4
New Jersey:“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADEDFIREARM WITHIN EASY ACCESS OF A MINOR.”
New York City:“THE USE OF A LOCKING DEVICE OR SAFETY LOCK ISONLY ONE ASPECT OF RESPONSIBLE FIREARMSSTORAGE. FOR INCREASED SAFETY, FIREARMSSHOULD BE STORED UNLOADED AND LOCKED IN ALOCATION THAT IS BOTH SEPARATE FROM THEIRAMMUNITION AND INACCESSIBLE TO CHILDREN ANDOTHER UNAUTHORIZED PERSONS.”
North Carolina:“IT IS UNLAWFUL TO STORE OR LEAVE A FIREARMTHAT CAN BE DISCHARGED IN A MANNER THAT AREASONABLE PERSON SHOULD KNOW IS ACCESSIBLETO A MINOR.”
Texas:“IT IS UNLAWFUL TO STORE, TRANSPORT, ORABANDON AN UNSECURED FIREARM IN A PLACEWHERE CHILDREN ARE LIKELY TO BE AND CANOBTAIN ACCESS TO THE FIREARM.”
Wisconsin:“IF YOU LEAVE A LOADED FIREARM WITHIN THEREACH OR EASY ACCESS OF A CHILD YOU MAY BEFINED OR IMPRISONED OR BOTH IF THE CHILDIMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITSTHE FIREARM.”
* * * * * * * * * * * * * * * * * * * * * * Please check with your licensed retailer or state police foradditional warnings which may be required by local law orregulation. Such regulations change constantly, and localauthorities are in the best position to advise you on such legalmatters.
5
FIREARMS SAFETY IS YOUR RESPONSIBILITY
SAFETY MUST BE THE FIRST AND CONSTANTCONSIDERATION OF EVERY PERSON WHO HANDLES
FIREARMS AND AMMUNITION.
This Instruction Manual is designed to assist you in learning how to useand care for your RUGER® Mark IVTM pistols properly. Please contact usif you have any questions.
Only when you are certain you fully understand the manual and canproperly carry out its instructions should you practice loading, unloading,etc. with live ammunition. If you have any doubts about your ability tohandle or use a particular type of gun safely, you should seek supervisedinstruction. Such personalized instruction often is available from localgun retailers, gun clubs or police departments. If none of these sourcescan help, visit www.nra.org or write to the following address:
National Rifle Association11250 Waples Mill RoadFairfax, VA 22030-7400
The person possessing a gun has a full-time job. You cannot guess; youcannot forget. You must know how to use your firearm safely. Do not useany firearm without having a complete understanding of its particularcharacteristics and safe use. Remember: There is no such thing as afoolproof gun.
OTHER CAUTIONS AND WARNINGS APPEARTHROUGHOUT THE MANUAL.
WARNINGS OF GREAT IMPORTANCE ARE FOUND ON THE FOLLOWING PAGES:
8
Bolt Ears
Bolt Stop PinBolt
Rear Sight
Barrel-Receiver Assembly
Front Sight
TriggerGuard
Trigger
MagazineReleaseButton
AmbidextrousSafety
(shown”ON”)
AmbidextrousSafety
(shown”ON”)
Take-downButton
‘Grooved Foot’of Magazine
Muzzle
Extractor
Grip Frame
Barrel Receiver
BoltStop
Figure 1
Figure 2
NOMENCLATUREMARK IV™ PISTOLS
9
LOCKING DEVICEINSTALLATION INSTRUCTIONS
• Always keep your firearm pointed in a safe direction,including when you are installing or removing yourlocking device.
• Always verify that your firearm is completely unloadedbefore installing your locking device.
• Do not install locking devices in the trigger guard;always keep your fingers and locking device outside thetrigger guard during device installation and removal.
• Store firearms, ammunition and keys separately andsecurely, away from children and careless adults; do notstore your firearm with the keys in the locking device.
• Do not attempt to work the action of your firearm withthe locking device in place; this may damage yourfirearm.
• While locking devices are an important aid to securitymeasures, they are not a substitute for safe firearmhandling and proper storage. Remember that anymechanical device can be bypassed with enough time,knowledge, determination and equipment.
LOCKING DEVICES MUST BE USEDSAFELY AND RESPONSIBLY
WARNING – USE OF LOCKING DEVICES
Do not store keysin lock.
It is important to use the locking device on your Ruger® firearm!
Keep the muzzle pointed in a safe direction and your fingers outside the triggerguard at all times during installation of the locking device!
To Install the Factory-Supplied Locking Device:1. Remove the magazine from your pistol.
2. Open the action completely, and verify that the firearm is completelyunloaded and contains no cartridges or cartridge cases!
Use the bolt stop to keep the action open during installation of the lockingdevice.
Correct Installation of Cable LockFor Ruger® MARK IV™ Pistols
3. Insert the cable directly into your pistol as shown in Figure 3.4. To lock: With the key turned to the farthest clockwise position, insert the
loose end of the cable into the lock. Turn the key counterclockwise andremove the key.
5. Once the lock is securely closed, pull firmly on the lock to test theconnection and be sure it is locked. Do not leave or store your firearm withthe key in the lock! Store your locked, unloaded firearm and the key insecure, separate locations, away from ammunition, children, andunauthorized adults.
10
Figure 3
WARNING–ALTERATIONSThis product was designed tofunction properly in its originalcondition. Alterations can make itunsafe. Do not alter any part or addor substitute parts or accessories notmade by Sturm, Ruger & Co., Inc.
DO NOT ALTER ANY GUN
11
FIREARMS ARE DANGEROUS WEAPONS
READ THE INSTRUCTIONS AND WARNINGS IN THISMANUAL THOROUGHLY AND CAREFULLY
BEFORE USING.
GENERAL INFORMATIONAND MECHANICAL CHARACTERISTICSRUGER® MARK IVTM pistols are the latest evolution of Ruger’s original 1949Standard Auto Pistol. RUGER® MARK IVTM improvements include the use ofa solid one-piece fully machined grip frame, a simple take-down mechanism foreasy disassembly and cleaning, an improved bolt stop leaver, an ambidextrousmanual safety, and a drop-free magazine release.
The RUGER® MARK IVTM Standard Models feature tapered barrels andfixed sights for inexpensive fun and practice.
The RUGER® MARK IVTM Target Models feature a heavy bull barrel andadjustable sights for target shooting and training.
The RUGER® MARK IVTM Competition Models feature a slab-sided,heavy barrel with target grips and adjustable sights.
RUGER® MARK IVTM Hunter Models feature a target-crowned, fluted bullbarrel, adjustable rear sight and a HiViz® light-gathering front sight.
The RUGER® MARK IVTM 22/45TM features a bull barrel, fully adjustabletarget sights and light weight polymer “22/45” grip frame that matches the gripangle of the popular “1911”-style pistol.
The RUGER® MARK IVTM 22/45TM LITE has a grip frame assembly made ofmolded synthetic polymer, with a grip shape and angle generally similar to“1911”-style .45 caliber pistols. The receiver is made of aerospace-gradealuminum and is ventilated, making the pistol very light.
The RUGER® MARK IVTM 22/45TM TACTICAL has a lightweight polymergrip frame with rubberized replaceable grip panels that simulate the classic feeland grip angle of the 1911. The barrel is threaded for the addition of muzzleaccessories, and Picatinny rails are factory-installed on this model.
12
All RUGER® MARK IVTM pistols have the same basic operating mechanism andinclude the following features with which the gun user should be thoroughlyfamiliar:
Bolt Stop: When the last shot has been fired and the magazine is empty, the boltstop automatically holds the bolt open. When there is an empty magazine in thepistol and the bolt is retracted manually, the bolt stop will automatically hold thebolt open. If a loaded magazine is inserted in the pistol when the bolt is closed andthe bolt is then retracted fully, the bolt stop will not automatically hold open thebolt. The user can actuate the bolt stop mechanism to hold the bolt open at anytime by retracting the bolt, pushing up on the bolt stop thumbpiece, and releasingthe bolt.
The bolt stop can be released when an empty magazine is in the pistol by drawingback slightly on the bolt and depressing the bolt stop thumbpiece. When the boltis released, it will move forward under pressure from the recoil spring.
The bolt stop is spring-loaded. Therefore, when there is a loaded magazine in placeand the pistol is jarred, the bolt may fly forward and chamber a cartridge. For thisreason and as an essential safety practice, the safety of the pistol should always bein the “on” (white dot showing) position except when the user is firing the gun ata selected target.
Magazines: Only use the correct RUGER® magazines for RUGER® MARK IVTM
pistols in order to ensure proper feeding, functioning of the bolt stop andengagement of the magazine disconnect safety.
The RUGER® MARK IVTM uses the same 10-shot magazine as the RUGER®
MARK IIITM pistol.
The RUGER® MARK IVTM 22/45TM uses MARK IVTM 22/45TM magazinesonly. MARK IVTM 22/45TM magazines are not compatible with the MARK IIITM
22/45TM.
Safety: The safety locks the sear when the safety is “on,” indicated by a white dotvisible on the grip frame. Because the safety cannot be moved to its “on” positionunless the hammer is cocked, the safety also serves as a cocking indicator. The boltcan be manually retracted and released when the safety is “on.” This featureallows the pistol to be loaded or unloaded when the safety is “on.” As shown inFigure 6 on page 13 and elsewhere in this manual, the safety should be “on” at alltimes except when the gun user is deliberately positioned to fire at a selectedtarget. When the safety is in the “off” or down position, it will allow the trigger tobe pulled and a red dot will be visible on the grip frame.
OPERATION OF MANUAL SAFETY
Putting the safety between “safe” and “fire”can result in the pistol firing when thetrigger is pulled. Always move the safetyfully to its intended position and check it.The safety is not “on” unless it iscompletely “on.” Never depend on a safetymechanism or any other mechanical deviceto justify careless handling or permittingthe pistol to point in an unsafe direction.The only “safe” pistol is one in which thebolt is open, the chamber is empty andthere is no magazine in the gun.
Figure 5. Safety in the “off” or “fire”position. Safety is all the way down andred dot is visible.
Figure 6. Safety in the “on” or “safe”position. Safety is all the way up and thewhite dot is visible.
WARNING–MANUAL SAFETY
NEVER PUT SAFETY 1/2 ON
The Safety is not “on” unless it is fully up with the white dot completelyvisible (see Figure 6).
13
AMMUNITIONThe RUGER® MARK IVTM pistols are chambered only for the. 22 Long Riflecartridge, standard velocity or high velocity, manufactured to U.S. IndustryStandards. Do not attempt to load .22 Long, .22 Short or any other type .22caliber cartridge into the magazine or in the chamber of the pistol. Use of .22shot shells is not recommended. See “Warning - Malfunctions,” p. 20.
Certain types of high velocity ammunition may show bulges or splits whenexamining the spent cases. If this occurs, discontinue using the ammunition.
14
WARNING–AMMUNITION
IMPROPER AMMUNITIONDESTROYS GUNS
AMMUNITION (CARTRIDGES) NOTICE
WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE ORINJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS
THE RESULT OF, THE USE IN RUGER® PISTOLS OF FAULTY, ORNONSTANDARD OR “REMANUFACTURED” OR HANDLOADED
(RELOADED) AMMUNITION OR OF CARTRIDGES OTHER THAN THOSEFOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.
Death, serious injury, and damage can resultfrom the wrong ammunition, boreobstructions, powder overloads or incorrectcartridge components. .22 cases are very thinand sometimes split when fired. Always wearshooting glasses and hearing protection.
WARNING – LEAD EXPOSUREDischarging firearms in poorly ventilatedareas, cleaning firearms or handlingammunition may result in exposure tolead and other substances known to theState of California to cause birth defects,reproductive harm, and other seriousphysical injury. Have adequate ventilationat all times. Wash hands thoroughly afterexposure.
SHOOTING OR CLEANING GUNSMAY EXPOSE YOU TO LEAD
DRY FIRINGGoing through the actions of cocking, aiming and pulling the trigger on anunloaded gun is known as “dry firing.” It can be useful to learn the “feel” of yourpistol. Be certain that the pistol is fully unloaded (both the chamber andmagazine are empty) and that the pistol is pointing in a safe direction when youare practicing dry firing. The RUGER® MARK IVTM pistol can be dry fired buta snap cap is strongly recommended for anything more than occasional dry firepractice.
CAUTION: When using the follower button, have it under control.When loading or handling the magazine, do not pull the button downand then release it suddenly. The rim of the cartridge hitting themagazine lips may set off a sensitive primer and cause the cartridgecase to discharge, burst violently, and result in injury
15
4. Engage the safety by moving it fully upward so the white dot is completelyvisible. (See Figure 6, p. 13.)
5. Put ten (10) or fewer .22 LongRifle cartridges into the magazine.In loading the magazine, makesure that all of the cartridges lieparallel and evenly in themagazine. The follower button onthe left side of the magazine isused to lower the follower so thecartridges can be readily inserted(see Figure 8).
Figure 7
TO LOAD AND FIREPractice this important aspect of gun handing (with an unloaded pistol) until youcan perform each of the steps — described below — with skill and confidence. Butbefore you do anything with the pistol, first read completely through this manual.
1. Keep the muzzle pointed in a safe direction. (See Rule 2, p. 42.)
2. Push the magazine release button and pull the magazine down out of the gripframe.
3. Grasp the grooved ears of the bolt and pull the bolt to the rear as far as it willgo. Then allow the bolt to go forward on an empty chamber. (See Figure 7, below.)This cocks the hammer and must be done before the safety can be put on.
FollowerButton
Figure 8
6. Insert the magazine into the magazine well, taking care that the magazine isfully inserted and locked in place with the cartridges pointing forward.Slamming the magazine into the grip frame is not necessary.
7. Keeping your fingers outside of the trigger guard, pull the bolt to the rear asfar as it will go (see Figure 7, p. 15.) Release the bolt so that it will fly forward.This will place a cartridge into the firing chamber. If the pistol is not to be firedimmediately, the safety button should remain “on” (see Figure 6, p. 13.).
Once the safety is disengaged (pushed down so the red dot is visible – seeFigure 5, p. 13), the pistol will fire a cartridge each time the trigger is pulled,until all of the cartridges in the magazine, and the one in the chamber, havebeen fired.
8. The pistol is ready for instant use once the safety is disengaged. Firing willautomatically reload and recock the pistol. Note that every time the trigger ispulled, if a cartridge is in the chamber and the safety is “off,” the pistol will fire— be careful!
WARNING–FIRING
9. Immediately following the firing of a shot, and if a subsequent shot is not tobe fired at once, put the safety in its “safe” position while the pistol is stillpointing in a safe direction down range. Never put a loaded pistol down with thesafety off!
10. When the last cartridge loaded into the pistol has been fired, the magazinefollower presses the slide stop upward to engage the slide, automatically holdingthe action open. If the slide is shut, the shooter should always assume that thereis a cartridge in the chamber!
Don’t rely on your memory to know if a gun or magazine is loaded. With thepistol pointed in a safe direction, visually inspect the magazine and the chamber.
BOLT OPENS FAST -HOT BRASS EJECTED
The bolt automatically opens and shutsquickly while firing. Keep face andhands away from rear. Hot brass isejected quickly and can burn you. Alwayswear shooting glasses and hearingprotectors.
16
17
WARNING–HANDLING
ANY GUN MAY FIRE IF DROPPED
If dropped or struck with the safety“off,” the pistol may fire. Keepchamber empty unless actuallyfiring! Keep safety “on” unlessactually firing!
OPERATION OFMAGAZINE DISCONNECT
Your RUGER® MARK IVTM pistol is equipped with a magazine disconnect.This device prevents the trigger from being pulled if the magazine is removedfrom the pistol. You will not be able to fire the pistol with the magazineremoved, however, you should not rely upon the magazine disconnect or anyother mechanical device or safety to justify careless or unsafe handling of anyfirearm.
Remember that a round may still be in the chamber and that the pistol may stillbe loaded even if the magazine is removed. As always, you should not rely uponthe magazine disconnect or any other mechanical device or safety to justifycareless or unsafe handling of any firearm.
Don’t rely on your memory to know if a gun or magazine is loaded. With thepistol pointed in a safe direction, visually inspect the magazine and the chamber.
TO UNLOAD, EXTRACT ANDEJECT A CHAMBERED CARTRIDGE
NOTE: This sequence must be followed exactly as spelled out. Failure to do socan result in the pistol’s chamber becoming unintentionally loaded with acartridge.
1. The muzzle of the pistol must be pointing in a safe direction at all times,and fingers must be outside the trigger guard. If the pistol is cocked, put thesafety “on” by pushing safety button fully upward so that the white dot is visible.
2. Remove the magazine from the pistol and place it where it will not getdamaged or collect dirt. (REMEMBER that even though the magazine has beenremoved, a cartridge may still be in the chamber.)
18
1
2 3
1
2
43
Safety “ON”
CORRECT UNLOADING SEQUENCE
3. Firmly hold pistol in right hand so that the right thumb is directlyunderneath the bolt stop thumbpiece. Grasp the bolt ears firmly between thethumb and forefinger of your left hand and briskly retract the bolt to itsrearmost position. As the bolt nears the end of its retraction, the chamberedcartridge should be extracted and ejected. When the bolt is fully retracted, pushupward on the bolt stop thumbpiece with your thumb, then allow the bolt tomove forward slowly until it comes to rest against the bolt stop.
Always visually double check the chamber and the interior area of thereceiver and the magazine well to be certain there are no cartridges present.Gently shake the pistol to dislodge any cartridge which may have been ejectedinto the magazine well when the bolt was retracted.
4. The gun is now unloaded. If it is desired to close the bolt on an emptychamber, visually inspect to ensure the chamber is empty. Ensure that themagazine is not in the pistol and that the safety is “on,” retract the bolt to itsrearmost position, release it, and the bolt will snap forward. Keep your fingersout of the receiver!
5. If the magazine contains cartridges, they can be removed by pressing downslightly on the magazine button (to ease the spring tension) with the thumb, andthen sliding the cartridges forward and out of the magazine, one at a time, untilemptied.
6. Push the empty (unloaded) magazine into grip frame until the latch locks itin place.
7. With the muzzle pointed in a safe direction, push the safety to the “off” (reddot visible) position and pull the trigger to decock the pistol.
19
TO CLEAR A MALFUNCTION (“JAM”)1. Be certain the muzzle is pointed in a safe direction and the safety is “on”(white dot visible).
2. If possible, first remove the magazine. It may be necessary to manuallyremove a jammed cartridge which has only partially been stripped from themagazine. If so, use extreme care. Lock the bolt open with the bolt stop beforeattempting to clear the jam (see Figure 9). Drawing the bolt fully to the rear maybring the jammed cartridge along. Keep your face away from the ejection portduring this operation. When attempting to clear a jam, use only wood “tools” sothat a cartridge will not be ignited if you strike a primer and so that the chamberand magazine will not be damaged. A 3/16" wood dowel rod with a point on oneend is useful.
3. Visually check to make sure all cartridges have been removed from thepistol. Safely dispose of any cartridges involved in a malfunction incident. Do notuse damaged ammunition in any firearm.
Bolt Stop
Figure 9
TO MINIMIZE MALFUNCTIONS (“JAMS”)1. Inspect the gun and magazine for excessive fouling, damaged or worn parts.If it appears that the gun and magazine are in good working order, then tryanother brand or type of ammunition.
2. If changing to another type or brand of cartridges does not at onceeliminate malfunctions, then the following steps should be taken:
a. Make certain the gun and the magazine are unloaded and that thesafety is “on” (white dot is visible). Remember, the magazine should beremoved first, then check the chamber and be certain it and themagazine well are clear of cartridges.
20
WARNING–MALFUNCTIONS
CRUSHING RIM CAN BURST AMMO
The .22 Long Rifle rimfire cartridge fires whenthe firing pin impacts the relatively softcartridge case rim, and also can be “discharged”before it is chambered if its rim receives a sharpblow. If a cartridge hangs up, jams or bindswhen being chambered or when being fed fromthe magazine into the chamber, do not attemptto force it into the chamber by pushing orstriking the bolt. Any jam or feeding problem isa signal to immediately stop using the gun untilit can be determined what is wrong. Mostfailures of a cartridge to feed or to chamber arecaused by a damaged magazine, improper gunhandling or defective ammunition. Whateverthe cause, rimfire cartridge jams can result inthe potentially very dangerous situation of acartridge discharging before it is chambered. Ifthis occurs, the cartridge case will rupture andits fragments will fly out of the gun withsufficient force to cause injury. Always wearshooting glasses and hearing protectors! Keepface away from chamber!
b. Thoroughly clean the magazine and bolt mechanism, payingparticular attention to removing accumulated grease. Use a bristlebrush and solvent to remove grease and fouling from the bolt face, theextractor, the chamber, and the feed ramp. (See the “Care andCleaning” section on page 26 of this manual for detailed cleaninginstructions.)
c. Check to see that the magazine spring tension is adequate.
d. Check the magazine lips to be certain they are free of nicks andburrs and are not deformed.
e. Remove excess oil and solvent from all cleaned components, load themagazine, and try the firearm again. As always, proceed slowly. Becertain bystanders are not close and that you are wearing eye andhearing protection and that your face is a safe distance from the pistolso that any discharge resulting from a jammed cartridge will not injureanyone.
If the above procedures do not result in a smooth and reliably functioningfirearm, do not use the pistol. The pistol can be returned directly to our PrescottCustomer Service Department for repair. See the Service and Parts Policy sectionof this manual for packing and shipping information.
Another precaution: when using any firearm chambered for rimfire cartridges,form the habit of examining fired cartridge cases. If they are bulged or showsplits on any part of the case, discontinue using the ammunition.
21
1
2 3 Always unload a firearmbefore cleaning, lubrication,disassembly or assembly.
UNLOAD BEFORESERVICING
WARNING – DISASSEMBLY
DISASSEMBLYRUGER® MARK IVTM pistols are designed to be disassembled and reassembledwithout the use of tools.
1. Before beginning disassembly, be certain that the muzzle is pointed in a safedirection. Keep your fingers out of the trigger guard. Remove the magazine andremove all cartridges from the magazine. Draw the bolt fully rearward and visuallyinspect the chamber to be certain that there is no cartridge in it and then release thebolt. Put the safety in the “on” position with the white dot visible.
2. Holding the barrel in one hand and the grip frame assembly in the other, depressthe take-down button located just below the rear of the bolt (see Figure 10).
DepressTake-downButton
Figure 10
22
3. With the take-down button pressed, tilt the barrel downward so that it clearsthe bolt stop pin (see Figure 11a). The barrel/receiver assembly can now be liftedstraight up off of the grip frame assembly (see Figure 11b).
DepressTake-downButton
Figure 11a
4. The grips can be removed from the grip frame assembly with a 3/32 Allenwrench if desired.
5. Pull straight back on the bolt ears to remove the bolt from the receiver (seeFigures 12).
No further disassembly is necessary.
Figure 11b
Figure 12
23
REMOVAL OF AMBIDEXTROUS SAFETYIf you prefer to have just the left safety lever, you can remove the right safetylever by following the instructions below.
1. To remove the right (ejectionport) side safety lever, first removethe right grip panel using a 3/32”hex wrench. (See Figure 13.)
NOTE: Removing the right sidegrip panel will expose themagazine ejector. The magazineejector is under spring tension andshould be covered with your handwhen removing the grip panel toprevent it from being dislodged.Safety glasses should be worn.
Figure 13
Figure 14 Figure 15
2. Next, remove the right side safety lever using a 1/16” hex wrench. (SeeFigure 14.)
3. Finally, install the supplied spacer in place of the safety lever (see Figure15), and reinstall the grip panel using the original screws.
24
4. Rotate the barrel/receiver assembly down on to the bolt-stop pin in the gripframe (see Figure 18).
3. Place the barrel/receiver assembly on top of the frame so that the notch inthe receiver aligns with the pivot pin in the grip frame (see Figure 17).
Figure 17
Align Notch andPivot Pin
Figure 18Bolt Stop Pin
Figure 16
REASSEMBLY(The procedure is the same for all RUGER® MARK IVTM pistols.)
1. Be certain the pistol is free of cartridges! Keep your finger out of the triggerguard. The safety must be in the "on" position with the white dot fully visible forreassembly (see Figure 6, p. 13).
2. Insert the bolt fully into the barrel/receiver assembly (see Figure 16).
MAGAZINE NOMENCLATURE
MAGAZINE DISASSEMBLYAlways wear safety glasses when
disassembling or reassembling a magazine!
TO DISASSEMBLE MAGAZINE: Withdraw the magazine from pistol and removeall cartridges from the magazine. Retract the bolt and check the chamber to becertain no cartridges remain in the pistol. Hold the magazine upside down sothat the hole in the Magazine Block is accessible.
25
FOR RUGER® MARK IV™ PISTOLS
6. Replace the empty magazine into the magazine well, point the pistol in asafe direction, place the safety in the “off” position to expose the red dot, and pullthe trigger to uncock the gun. Guns should not be stored loaded or cocked.
5. Gently squeeze the barrel/receiver assembly and the grip frame assemblytogether so that a click is heard and check to ensure that they are firmlytogether and cannot be pulled apart (see Figure 19).
Figure 19
26
MAGAZINE DISASSEMBLY
3
5
1 42
Slide BlockForward
Push UpRemoveButton
Remove Spring& Plunger
Remove Follower
DAMAGED, NON-STANDARD OR IMPROPERLYASSEMBLED MAGAZINES SHOULD NOT BE USED.THEY CAN CAUSE THE PISTOL TO MALFUNCTION.
1. With right hand, insert drift punch in hole and depress Magazine BlockRetaining Plunger approximately 1/4".
2. Slide Magazine Block forward slowly BEING VERY CAREFUL TO KEEPPLUNGER AND SPRING UNDER CONTROL. If not contained, these parts will flyout with considerable force. Therefore keep bottom end of magazine pointedaway from persons and objects.
3. With the Magazine Block fully removed, the Plunger and Spring should beslowly withdrawn.
4. Now, holding the magazine flat in the left hand, align the Magazine FollowerButton with the circular opening near the lower end of magazine body and liftout the Magazine Follower Button.
5. The Magazine Follower can then be removed.
Reassemble in reverse order, being careful to contain the Spring and Plunger asthe Magazine Block is slid and locked into place. After reassembly has beencompleted, test Magazine Follower to ensure it has free movement.
Always ‘ride’ the Magazine Follower Button up and down with your thumb.Do not lower Follower Button and then permit it to snap up.
WARNING – LUBRICATION
CARE AND CLEANINGMake Sure Gun is Unloaded!
Before cleaning, be certain the pistol and its magazine are unloaded (see “To Unload,”p. 17).
At regular intervals, or whenever the pistol has been exposed to sand, dust, extremehumidity, condensation, immersion in water or other adverse conditions, disassemble,clean, and oil it. Proper periodic maintenance is essential to the reliable functioning ofany firearm.
To clean the pistol, proceed as follows;
1. Disassemble (field-strip) the pistol to the extent described on pages 21 - 22.
2. Using a cleaning rod, run a properly sized, solvent-wetted patch through the boreseveral times. Then attach a solvent-wetted bristle brush to a cleaning rod and run itback and forth the full length of the bore as many times as necessary to remove greaseand dirt from the bore and chamber. Clean the bore with dry patches and examine. Borefouling can contribute to reduced accuracy, and grease accumulation in the chambercan interfere with proper feeding of cartridges from the magazine.
3. Using powder solvent on a clean patch or bristle brush, remove powder residuefrom all components of the pistol. After cleaning, run a dry patch through the bore,then follow with a patch that is very lightly oiled. Wipe all surfaces clean with a cloth,then wipe all surfaces with a patch or cloth that has been very lightly oiled.
4. NOTE: Only a light application of oil is needed to provide adequate lubrication ofmoving parts and to prevent rust. Excess accumulations of oil tend to attract particles ofdust and dirt and may congeal in cold weather which can interfere with the safe andreliable function of the pistol.
5. If magazine becomes dirty, it should be disassembled and thoroughly cleaned (see“Magazine Disassembly” section, p. 25).
6. Before firing, remove all oil and grease from the bore.
27
IMPROPER LUBRICATIONDESTROYS GUNS
Firing a pistol with oil, grease, or any othermaterial even partially obstructing the bore mayresult in damage to the pistol and serious injury tothe shooter and those nearby.
Do not spray or apply lubricants directly onammunition. If the powder of a cartridge is affectedby the lubricant, it may not be ignited, but theprimer firing may push the bullet into the borewhere it may become lodged. Firing a subsequentbullet into the obstructed bore may damage thepistol and cause serious injury or death to theshooter and those nearby. Use lubricants properly.You are responsible for the proper care andmaintenance of your firearms.
28
STORAGEGUNS SHOULD NOT BE STORED LOADED!
USE THE LOCKING DEVICE SUPPLIEDWITH THE PISTOL TO RENDER ITINOPERATIVE FOR SAFE STORAGE.
(SEE PAGE 9)
•Never place or store any firearm insuch a manner that it may bedislodged. Firearms should always bestored securely and unloaded, awayfrom children and careless adults.
•Use the locking device supplied withthe pistol for storage. The use of alocking device or safety lock is only oneaspect of responsible firearms storage.
•For increased safety, firearms shouldbe stored unloaded in a location that isboth separate from their ammunitionand inaccessible to children and anyother unauthorized person.
STORE SECURELY & UNLOADED
WARNING–STORAGE
INSTRUCTIONS FOR ATTACHINGTHE SCOPE BASE
1. Remove the filler screws from the top of the receiver.
2. Degrease the screw holes in the receiver.
3. Degrease the scope base screws.
4. After the degreased areas are dry, place a drop of blue LOCTITE®
adhesive/sealant or equivalent to the scope base screws.
5. Set the scope base on the receiver with the side notch aligned with theejection port of the receiver.
6. Install the scope base screws and tighten.
7. Set the assembled pistol aside overnight to allow the adhesive to set up.
Do not keep the pistol stored in a leather holster or case. Leather attractsmoisture, even though the holster or case may appear to be perfectly dry.
SIGHT ADJUSTMENTThe Standard RUGER® MARK IVTM pistol is equipped with a rear sight whichis adjustable for windage only. The rear sight can be drifted laterally in itsdovetail on the top of the slide by tapping it with a wooden or plastic headedhammer or similar implement. The front sight is fixed.
Models equipped with adjustable sights: Turning the top (elevation) sightadjustment screw clockwise lowers the impact of the shot. Turning thehorizontal (windage) sight adjustment screw clockwise moves the impact of theshot to the left.
29
SUGGESTED SIGHT PICTURE
Top of front sight even with top ofrear sight blade. Front sightcentered in notch of rear sightblade. Target bull’s-eye centered ontop of front sight.
SUGGESTED SIGHT PICTURE FORV-NOTCH REAR SIGHTS(On Models So Equipped)
A v-notch express sight is designed tobe used as a point of aim/point ofimpact sighting system. Therecommended sight picture for thistype of system is to place the roundfront sight bead, regardless of the sizeof the bead, at the bottom of the v-notch in the rear sight. The front sightbead should be pointed directly at theintended target.
CHANGING THE LITEPIPEON YOUR HiViz® SIGHT(On Models So Equipped)
1. Point the muzzle in a safe direction.
2. Make sure that the magazine and the pistol are completely unloaded.
3. Use the tip of the HiViz® key to push the LitePipe in and out of the sight base.
MUZZLE CAP REMOVALINSTRUCTIONS
(On Pistols So Equipped)Some Ruger® MARK IVTM pistols come equipped with a threaded barrel thatis protected by a removable muzzle cap. The cap protects the 1/2”-28 threads atthe end of the barrel, which is designed to accommodate a .22 Long Rifle soundsuppressor.
To remove the muzzle cap, point the pistol in a safe direction, remove themagazine, and keep your finger off the trigger. Retract the bolt to the rear, andlock it to the rear by pushing up on the bolt stop. Verify that the chamber isempty. Pull back on the bolt ears and release to close the bolt. Keep your fingersout of the receiver!
Hold the upper receiver/barrel section of the pistol firmly in your left hand, andturn the muzzle cap counter-clockwise, until removed from the threaded portionof the barrel. (See Figure 20a.) Gripping the muzzle cap by the knurled sectionwill aid in twisting the cap free. Remove the cap and the wave washer under thecap (See Figure 20b.) and store them in a safe place for reinstallation when thesuppressor is removed.
Figure 20a Figure 20b
Install the suppressor per the manufacturer’s instructions. (See Figure 21.) Whena suppressor is not being used, reinstall the wave washer and muzzle cap toensure the threads at the end of the barrel are protected.
Figure 21
30
WARNING – BARREL NUTWhen removing the muzzle cap, a barrelnut is behind the cap and washer. This nutis used to lock the barrel in place. Thisnut should never be loosened, removed ortampered with. This nut is epoxied andtorqued in place at the factory. This nut ismeant to remain in place and should notbe removed under any circumstance.Failure to follow this warning will causepermanent damage to your firearm andwill not be warranted or repaired byCustomer Service.
DO NOT REMOVEBARREL NUT
DO NOT RemoveBarrel Nut
31
SERVICE AND PARTS POLICYIf you have any questions with regard to the performance of your RUGER®
MARK IVTM pistol, please call (336-949-5200) or write our Prescott, ArizonaCustomer Service Department, fully describing all circumstances and conditionsinvolved. If you should return your pistol to the factory for repair, or order partsfor it, please comply with the following suggestions for prompt service:
32
SHIPPING FIREARMS FOR REPAIR
RUGER® MARK IVTM pistols returned to the factory for service or repair should besent to: Ruger, Customer Service Department, 200 Ruger Road, Prescott, AZ 86301-6181. NOTE: You must obtain a Repair Authorization Number before returning yourfirearm. An authorization number can be obtained by contacting Customer Serviceonline at www.ruger.com or calling the Customer Service Dept. at 336-949-5200. Gunsshould be sent prepaid. We will not accept collect shipments.
The Federal Gun Control Act, as well as the laws of most states and localities, do notprohibit an individual (who is not otherwise barred from purchasing or possessing afirearm) from shipping a firearm directly to the manufacturer for repair. However,before you ship your firearm to us, be certain that your state or locality does not have alaw or regulation which will prohibit you from receiving it from us after it has beenrepaired. If such receiving is prohibited, then please have a federally licensed firearmsdealer ship the gun to us. If it is sent to us by a dealer, it will be returned to that dealerafter being repaired. If a handgun (pistol or revolver) is shipped by an individual whodoes not hold a Federal Firearms License, it must be shipped for overnight delivery viaU.P.S., Federal Express, or other similar private overnight service. NOTE: Handgunsmay not be shipped via U.S. Mail. Persons who do not hold a Federal Firearms Licenseare prohibited by Federal law from shipping a handgun by Mail. Handguns mailed inviolation of the law are impounded by the Post Office.
Please do not include holster, custom grip panels or custom accessories with a firearmbeing shipped to the factory for service. Guns that have been customized or modifiedwith non-factory parts may be reset to original factory condition. High capacitymagazines should not be sent if coming from a restricted state. DO NOT SEND GUNBOXES OR LITERATURE THAT YOU CONSIDER TO BE COLLECTOR’S ITEMS -THESE ARE INVARIABLY DAMAGED OR DESTROYED IN SHIPMENT. Alwaysinsure your shipment.
Enclose a letter which includes your name, address, telephone number, email address,serial number and model of the firearm and your repair authorization number. Describein detail the trouble you have experienced with your firearm, or the work you wish tohave done. Merely stating that the firearm “needs repair” is inadequate information.State precisely what is wrong. Please enclose copies of any previous correspondence.
Most models can be refinished, but custom gunsmithing service or nonstandardalterations are NOT AVAILABLE from Ruger Customer Service Departments.
WARNING—BEFORE SHIPPING ANY FIREARM,BE ABSOLUTELY CERTAIN THAT THE FIREARM ANDITS MAGAZINE ARE UNLOADED. DO NOT SHIPCARTRIDGES WITH A FIREARM.
33
ORDERING PARTSPlease contact the Prescott, Arizona Customer Service Department for partsavailability and current prices. All parts ordered for the RUGER® MARK IVTM
should be sent to: Ruger, Parts Department, 200 Ruger Road, Prescott, AZ86301-6181, telephone: 336-949-5200.
We cannot comply with open account or C.O.D. requests. Payment in full viacredit card (Visa, MasterCard or Discover only), money order or certified bankcheck (no personal checks or cash, please) is required before any service will beperformed. Please provide your credit card number, your name as it appears onthe credit card, the expiration date and 3-digit security code. All parts orders aresubject to a minimum charge and charges for shipping and handling. Orderparts by Part Name and specify the model and the entire serial number of thefirearm for which the parts are being ordered. There is a minimum labor chargeplus a shipping and handling charge if the parts are factory fitted. All factoryfitted parts are fit on an exchange basis only. We will not return the replacedparts. Please contact the Customer Service Department for pricing information.
*Parts designated by an asterisk must be factory fitted. These parts are fitted onan exchange basis only. We will not return the replaced parts. We will not returnany part that is broken, malfunctioning, badly worn or has been modified. See“Warning – Parts Purchasers” above.
Because it is a serial-numbered component, the RUGER® MARK IVTM pistolbarrel/receiver assembly is defined as a “firearm” by Federal Law and is notoffered for sale separately.
WARNING: A gun containing broken, malfunctioning or badlyworn parts should not be fired.
• It is the purchaser’s responsibility to beabsolutely certain that any parts ordered fromthe factory are correctly fitted and installed.
• Firearms are complicated mechanisms andIMPROPER FITTING OF PARTS MAY RESULTIN A DANGEROUS MALFUNCTION, DAMAGETO THE FIREARM, AND SERIOUS INJURY TOTHE SHOOTER AND OTHER PERSONS.
• The purchaser and installer of parts mustaccept full responsibility for the correctadjustment and functioning of the firearmafter such installation.
PARTS MUST FIT CORRECTLY
WARNING–PARTS PURCHASERS
34
Key No. Part Name* 1 Grip Frame * 2 Frame Lug 3 Receiver Frame Screw 4 Bolt Open Stop Spring 5 Trigger Spring 6 Trigger Spring Plunger 7 Bolt Open Stop * 8 Trigger Bar 9 Trigger Bar Pivot Pin 10 Trigger Pivot Pin 11 Magazine Latch 12 Magazine Latch Spring 13 Magazine Latch Screw* 14 Sear 15 Sear Spring 16 Hammer Bushing* 17 Hammer 18 Hammer Strut 19 Magazine Disconnector Spring* 20 Safety 21 Spring Plunger for Auto Safety* 22 Safety Lever, Left 23 Safety Lever, Right* 24 Main Spring Housing 25 Hammer Spring 26 Hammer Spring Plunger 27 Latch Spring* 28 Latch * 29 Bolt Stop Pin 30 Bolt Stop Thumbpiece 31 Left Grip Panel 32 Grip Panel Screw 33 Right Grip Panel
* PARTS SO MARKED MUST BE FACTORY FIT.
RUGER®MARK IV™
PARTS LISTDesign, prices and specifications subject to change without notice.
SPECIFY MODEL, CALIBER, AND SERIAL NO. WHEN ORDERING(See Exploded View on page 36)
† Because it is a serial-numbered component, the RUGER® MARK IVTM pistolbarrel/receiver assembly is defined as a “firearm” by Federal Law and is notoffered for sale separately.
THE BASIC RULES OF SAFE FIREARMS HANDLINGWe believe that Americans have a right to purchase and use firearms for lawfulpurposes. The private ownership of firearms in America is traditional, but thatownership imposes the responsibility on the gun owner to use his firearms ina way which will ensure his own safety and that of others. When firearms areused in a safe and responsible manner, they are a great source of pleasure andsatisfaction, and represent a fundamental part of our personal liberty.
Firearms do not cause accidents! Firearms accidents are almost always foundto have been the result of carelessness or ignorance on the part of the shooterof the basic rules of safe gun handling.
The following rules must be observed by gun users at all times. Safe gunhandling is not just desirable, it is absolutely essential to your safety, the safetyof others, and the continuation of gun ownership and sport shooting as weknow it today.
1. LEARN THE MECHANICAL AND HANDLINGCHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. Themethod of carrying and handlingfirearms varies in accordance with themechanical provisions for avoidingaccidental discharge and the variousproper procedures for loading andunloading. No person should handle anyfirearm without first having thoroughlyfamiliarized himself with the particulartype of firearm he is using, and with safegun handling in general.
2. ALWAYS KEEP THEMUZZLE POINTED IN ASAFE DIRECTION.
Be sure of the bullet stop behind yourtarget, even when dry-firing. Never letthe muzzle of a firearm point at any partof your body or at another person. This isparticularly important when loading orunloading a firearm. In the event of anaccidental discharge, no injury can occuras long as the muzzle is pointing in a safedirection. A safe direction means adirection that will not permit adischarged bullet to strike a person, or tostrike an object from which the bulletmay ricochet.
43
A safe direction must take into account the fact that a bullet maypenetrate a wall, ceiling, floor, window, etc., and strike a person ordamage property. Make it a habit to know exactly where the muzzle ofyour gun is pointing whenever you handle it, and be sure that you arealways in control of the direction in which the muzzle is pointing, evenif you fall or stumble. Keep your finger off the trigger until you areready to shoot!
3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN
USE.
Firearms should be loaded onlywhen you are in the field or onthe target range or shooting area,ready to shoot. Firearms andammunition should be securelylocked in safes, racks or cabinets,or by using the locking devicesupplied with the firearm, whennot in use. Ammunition shouldbe safely stored separate fromfirearms. Store your firearms outof sight of visitors and children.It is the gun owner’sresponsibility to be certain that
children and persons unfamiliar with firearms cannot gain access tofirearms, ammunition, or components.
4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONSBEFORE SHOOTING.
Even a bit of mud, snow or excesslubricating oil or grease in thebore may cause the barrel to bulge,or even burst on firing, and cancause serious injury to the shooterand bystanders. Be sure that youare using ammunition of theproper caliber and loading for thegun you are using. If the report orrecoil on firing seems weak, ordoesn’t seem quite right, CEASEFIRING IMMEDIATELY, unloadyour firearm, and check to be surethat no obstruction has becomelodged in the barrel.
1
2 3
5. BE SURE OF YOURTARGET BEFORE YOUSHOOT.Don’t shoot unless you knowexactly where your bullet is goingto strike. Be sure of the bulletstop behind your target, evenwhen dry-firing with an unloadedgun. If you are in the fieldhunting, do not fire at amovement or noise. Take the timeto be absolutely certain of yourtarget before you pull the trigger.
6. WEAR SHOOTINGGLASSES AND HEARINGPROTECTION WHENYOU SHOOT.All shooters should wearprotective shooting glasses andadequate hearing protection whenshooting. Exposure to shootingnoise can damage hearing, andwearing adequate eye protectionwhen shooting is essential.
7. NEVER CLIMB A TREEOR FENCE WITH ALOADED FIREARM.Put the firearm down carefullybefore climbing a fence, andunload it before climbing ordescending a tree or jumping overa ditch or other obstruction.Never pull or push a loadedfirearm toward yourself or anotherperson. When in doubt, orwhenever you are about to doanything awkward, unload yourgun!
44
45
8. DON’T SHOOT AT AHARD SURFACE OR ATWATER.Bullets can glance off manysurfaces like rocks or the surfaceof water and travel inunpredictable directions withconsiderable velocity.
9. NEVER TRANSPORT ALOADED FIREARM.Firearms should always beunloaded before being placed in avehicle. A suitable carrying caseor scabbard should be used tocarry an unloaded firearm to andfrom the shooting area.
10. AVOID ALCOHOLICBEVERAGES WHENSHOOTING.Don’t drink until the day’sshooting is over. Handlingfirearms while under theinfluence of alcohol in any form,or medications that could affectyour judgment or coordination,constitutes a criminal disregardfor the safety of others.
46
A BRIEF ACCOUNT OF AN EXTRAORDINARYACHIEVEMENT: RUGER® FIREARMS
Sturm, Ruger & Company, Inc., had its beginning in a small machineshop occupying a rented frame building in Southport, Connecticut. InJanuary, 1949, with an initial investment of only $50,000 and an idea,William B. Ruger and Alexander M. Sturm started production of a .22caliber autoloading pistol–a design which was so successful that itbecame the cornerstone upon which one of the most comprehensivelines of sporting firearms ever made in America was established. AfterAlex Sturm’s death in 1951, William B. Ruger continued to direct theCompany until his death in 2002. William B. Ruger, Jr. continued toprovide guidance, which helped make this Company a sound andsuccessful enterprise, until his retirement in 2006. The Company hascontinued to prosper, under new management and guidance from ourBoard, with new products and fresh perspectives.
Ruger, in this relatively short time, has established itself as a leadingsmall arms design organization, developing a unique and broad line offine quality sporting, military and police firearms to become one of theworld’s most famous producers of revolvers, pistols, rifles and shotguns.Since 1949, Ruger craftsmen have built many millions of firearms.
During its five decades of growth and progress under the leadership ofWilliam B. Ruger, the Company developed a business philosophy andimplemented policies which represent a constructive influence in the lifeof modern America. From the beginning, Ruger played a positive role inconservation efforts and has supported the interests of shooters throughsuch groups as the National Rifle Association, National Shooting SportsFoundation, and many regional sportsmen’s organizations.
The Company has always endeavored to market its firearms forconstructive and recreational purposes, to emphasize the traditional andresponsible aspects of shooting, to render meaningful public services,and to encourage shooters in constructive, responsible, and safeparticipation in the shooting sports. Its motto, “Arms Makers ForResponsible Citizens®,” exemplifies this Company philosophy.
Today, Ruger® is particularly mindful of those elements which havecontributed to the creation of its success, and extends heartfelt thanks toits many loyal employees and customers.
The firearms catalog, and instruction manuals for all Ruger® firearms,can be downloaded from our website at:
www.ruger.com
NOTES
47
WHY NO WARRANTY CARD HAS BEENPACKED WITH THIS NEW RUGER® FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require anyseller or manufacturer of a consumer product to give a writtenwarranty. It does provide that if a written warranty is given, it must bedesignated as “limited” or as “full” and sets minimum standards for a“full” warranty. Sturm, Ruger & Company, Inc. has elected not toprovide any written warranty, either “limited” or “full”, rather than toattempt to comply with the provisions of the Magnuson-Moss Act andthe regulations issued thereunder. There are certain implied warrantiesunder state law with respect to sales of consumer goods. As the extentand interpretation of these implied warranties varies from state tostate, you should refer to your state statutes. Sturm, Ruger &Company wishes to assure its customers of its continued interest inproviding service to owners of Ruger® firearms.
STURM, RUGER & Company, Inc.200 Ruger Road
Prescott, Arizona 86301 U.S.A.www.ruger.com
Arms Makers For Responsible Citizens®
A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGER®
FIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST, OR IT MAY BEDOWNLOADED FROM OUR WEBSITE AT WWW.RUGER.COM.
THESE INSTRUCTION MANUALS CONTAIN IMPORTANTWARNINGS WHICH MUST BE UNDERSTOOD
BEFORE USING THESE FIREARMS.The Following are Sturm, Ruger & Co., Inc. Trademarks: “BX-Trigger,” “Bisley,” Eagle Hard “R” logo holding gun,“Elite 452,” “Gold Label,” “I’m a Ruger American,” “LC6,” “LCR-357,” “LC380CA,” “Mark II,” “Mark III,” “MatchChampion,” “Model 96,” “P345,” “P345D,” “P345PR,” “P85,” “P90,” “P91,” “P93,” “P94,” “P95,” “P97,” “R.I.O.S.,”“Ruger Marksman Adjustable,” “Ruger 77/50,” “Ruger 10/17,” “Ruger Titanium,” “77/357,” “Single-Seven,” “SR45,”“SR-556C,” “SR-556VT,” “SR-762,” “Target Grey,” “10/22-FS,” “This is Ruger. This is America.,” “Tri-Flex,” “22Charger,” “22/45,” and “22/45 RP.”
The Following are Registered U.S. Trademarks Belonging to Sturm, Ruger & Co., Inc.: Sturm,Ruger Logo,” “AC-556,” “AR-556,” “Arms Makers For Responsible Citizens,” “All-Weather,” “Bearcat,” “Blackhawk,” “BX-15,” “BX-25,”Eagle ‘R’ - soft ‘R’ & hard ‘R’,” Eagle ‘SR’,” “Everything you need and nothing you don’t.,” “GP100,” “Hawkeye,”“It’s Mine and It’s American,” “It’s Mine. And It’s American,” “LC380,” “LC9,” “LC9s,” “LC9s Pro,” “LCP,” “LCR,”“LCRx,” “M77,” “Mini Thirty,” “Mini-14,” “9E,” “Old Army,” “Power Bedding,” “Redhawk,” “RUGER,” “RugerAmerican Pistol,” “Ruger American Rifle,” “Ruger American Rimfire,” “Ruger Hunting” - phrase & logo design,“Ruger Inside & Out” - phrase & logo design, “Ruger Precision Rifle,” “Ruger 77/17,” “Ruger 77/22,” “Ruger 77/44,”“Ruger SP101,” “Ruger 10/22 Takedown” phrase & logo design, “Ruger 22/45 Lite,” “Ruger Vaquero,” “Rugged,Reliable Firearms,” “Security-Six,” “Service-Six,” “Silent-SR,” “Single-Nine,” “Single-Six,” “Single-Ten,” “Speed-Six,”the “SR” Design, “SR9,” “SR9c,” “SR40,” “SR40c,” “SR-22,” “SR22,” “SR-556,” “SR-556E,” “SR-556 Takedown,”“SR1911,” “Super Redhawk Alaskan,” and “10/22.”
