Contents
2
IntroductionIntroduction 3Applications 3Main constructional features 4
Performance rangePerformance range, S pumps 5Performance range, S pumps, range 70 5
IdentificationType key 6Pump nameplate 7FM approval plate 7
Selection of productOrdering a pump 8
Product rangeStandard range 9Standard pumps with stainless steel impeller 10Explosion-proof pumps 11Explosion proof pumps with stainless steel impeller 12
VariantsList of variants 13
ConstructionSectional drawings, motors 14Sectional drawings, pumps 18Components and material specification 23
Product descriptionFeatures 24Operating conditions 25Motor range 25Explosion-proof pumps 26Pump controllers 26Wiring diagrams 27
Curve charts and technical dataHow to read the curve charts 28Curve conditions 29Performance tests 29Certificates 29Witness test 29
Performance curvesTechnical dataS 70 low pressure, 6- and 8-pole 30S 70 medium pressure, 4- and 6-pole 32S 70 medium pressure, 6- and 8-pole 34S 70 high pressure, 4-pole 36S 70 high pressure, 6- and 8-pole 38
AccessoriesAccessories (for installation) 40Other accessories 41
DimensionsInstallation on auto coupling 42Dry pit, vertical installation 44Dry pit, horisontal installation 46
Further product documentationWebCAPS 48WinCAPS 49
S pumps, range 70Introduction
IntroductionThis product guide deals with Grundfos heavy-duty sewage pumps called S pumps, range 70.
This product guide was printed in July 2010. A newer version might be available from Grundfos WebCAPS. Go to WebCAPS Literature to locate and download the latest version - or insert the link below directly in your browser to get to the download page:
http://net.grundfos.com/Appl/WebCAPS/
Using the PDF version of this data booklet offers extra features to the booklet. Double-clicking a product number listed in the data booklet will open an internet browser window displaying all technical information available on the product.
Fig. 1 S pump, range 70
The S pumps, range 70, are a range of free-flow chan-nel impeller pumps specifically designed for pumping sewage and wastewater in a wide range of municipal, private and industrial applications.
The pumps are made of resistant materials, such as cast iron and stainless steel. These materials ensure a proper operation.
The pumps are fitted with motors from 107 hp to 188 hp (80 kW up to 140 kW). The motors are either 4, 6- or 8-pole motors, depending on the motor size.
The free passage in the pumps is 3.5 to 5.7" (90 to 145 mm).
The pumps are available for:
• submerged installation on auto-coupling system• submerged installation, free-standing• dry-pit installation, vertical• dry-pit installation, horizontal.
ApplicationsThe S pumps, range 70, are designed for applications, such as:
• raw water intake• wastewater treatment plants• municipal pumping stations • public buildings • residential housing• blocks of apartments• industries• parking garages • underground car parks • car wash areas • restaurants and hotels. The pumps are suitable for both temporary and perma-nent installation. The lifting bracket fitted on the pumps facilitates easy transportation to as well as installation at the installation site.
GrA
7832
3
Introduction S pumps, range 70
4
Main constructional features• leak-proof connections via the Grundfos SmartSeal
gasket system• double mechanical shaft seal system for reliable
sealing between pumped liquid and motor• watertight cable entry of corrosion-resistant polya-
mide or cast iron for FM approved pumps• moisture switch for continuous monitoring of motor
housing and automatic cut-off of power in case liq-uid penetrates
• self-cleaning channel impeller with long vanes re-ducing the risk of jamming or clogging, or SuperVor-tex impeller with high pumping efficency and less downtime
• SmartTrim system allowing easy adjustment of im-peller clearance and maintaining maximum pump efficiency over pump lifetime
• motor in insulation class (356 °F (180 °C)), enclo-sure class IP68 with three thermal sensors in stator windings
• seal condition monitoring via water-in-oil sensor (optional)
• explosion-proof motors for applications involving high risk of explosion
• stainless steel versions for use in corrosive or ag-gressive liquids:Q: stainless steel impeller, cast iron pump and mo-tor housing.
S pumps, range 70
5
Performance range
Performance range, S pumps
Performance range, S pumps, range 70
TM04
655
7 06
10TM
04 6
610
0610
100 150 200 300 400 500 8001000 1500 2000 3000 5000 10000 15000
Q [US GPM]
6
8
10
15
20
30
40
60
80
100
150
200
300
[ft]H
1010 20 30 40 50 60 7080 100100 200 300 400 600 800Q [l/s]
2
3
4
5
6
8
1010
20
30
40
50
60
80
[m]H
60 Hz
50
54
58
62
66
70
20000
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 14000
Q [US GPM]
25
30
40
50
60
70
80
100
150
200
250
[ft]H
0 100 200 300 400 500 600 700 800 Q [l/s]
8
9
1010
20
30
40
50
60
70
[m]H
60 Hz
S PumpsRange 70
S3.45.A120
S2.55.A120
S2.40.A80
S3.45.A200
S245
A100
S2.35.A80
6
S pumps, range 70Identification
Type keyCode Example S 2 .45 .A100 .1880 6 .70H .H .465 .G .N .D
SST
Pump type:Grundfos sewage and wastewater pumpMulti-channel impeller pump installed in a column pipe
1V
Impeller type:Single-channel impellerSuperVortex (free-flow) impeller
Pump passage:Maximum solids size = Code number from type designation/10 [inch
A100
Pump discharge:Nominal diameter of pump discharge port = Code number from type designation/10 [inch]10"
Output power, P2:P2 = Code number from type designation/10 [hp]
246
Number of poles: 2-pole motor4-pole motor6-pole motor
70H70M70L
Pump range / Pressure version:High pressureMedium pressureLow pressure
SCDH
Installation:Submersible installation without cooling jacketSubmersible installation with cooling jacketDry installation, verticalDry installation, horizontal.
Actual impeller diameter:[mm]
GMaterial code for impeller, pump and motor housing:Impeller, pump housing and motor housing: Cast iron
NEx
Pump version:Non-explosion-proof pumpExplosion-proof pump
BCD
Sensor version:B = S pump with built-in SM 111 module. PTC sensors are connected directly to IO 111 or other PTC relay.C = Not in useD = S pump without built-in SM 111 module.
Z Custom-built products
Identification S pumps, range 70
Pump nameplate
Fig. 2 Pump nameplate
FM approval plate
Fig. 3 Ex approval plate
The approval plate gives the following details:
TM04
649
4 12
10
Pos. Description
1 Type designation2 SAP code 3 Serial number4 Maximum ambient temperature5 Maximum head6 Maximum flow7 Maximum installation depth8 Enclosure class9 Number of phases
10 Frequency11 Rated speed12 Voltage/current, delta connection13 Voltage/current, star connection14 Power input/output15 Service factor16 Power factor17 Insulation class18 Production code, year/week19 Weight of the pump20 Model
2
1
3579
1013141618
20468
1112
1719
15
TM04
649
5 02
10
FM symbol
II Equipment group (II = non-mining)2 Equipment category (high protection)G Type of explosive atmosphereCE CE mark1180 Number of quality assurance notified bodyEx Motor explosion-proof according to FM standardb Control of ignition sourcesc Constructional safetyd Motor withstands explosion pressureIIB Gas group (Ethylene)T3C Maximum surface temperature of the motor is
320 °F (160 °C)T4 Maximum surface temperature of the motor is
275 °F (135 °C)Gb Equipment protection level, zone 1Baseefa Certificate numberFM Certificate number
FM
7
S pumps, range 70
8
Selection of product
Ordering a pumpWhen ordering an S pump, range 70, you need to take the following four aspects into consideration.
1. Pump2. Custom-built variation (option)3. Accessories4. Controller.
PumpUse the selection tool in WebCAPS to find the best suited pump for your application or use the section Product range on page 9 and the section Type key on page 6 to identify the pump that best fulfils your needs. The list below is a detailed description of the product you get if you order the following pump:
• Pump as specified in the type key• 50 ft (15 m) cable• Paint: Graphic grey, NCS S8005-R80B, thickness
150 μ • Three thermal switches (Klixon), one in each phase,
or three thermal sensors (PTC)• One moisture switch below the motor top cover (two
moisture switches below the motor top cover on explosion-proof versions)
• ANSI-HI centrifugal pump test 1.6-2000, Acceptance level B.
See section Performance curves Technical data for selection of a standard pump.
Note: Product specific data for the pump can also be seen in WebCAPS using the product number 97632349.
Custom-built variantsThe S pumps can be customised to meet individual requirements. Many pump features and options are available for customisation, e.g. explosion-proof versions, various cable lengths or special materials.
Variants can be seen in section List of variants on page 13. For requirements or designs not included in the list, contact Grundfos.
AccessoriesDepending on the installation type, you may need to order accessories. See section Accessories on page 40 for selection of the correct accessories.
Note: Ordered accessories are not fitted from factory.
ControllerThe following controllers are available:
Grundfos Dedicated Controls (DC).Pump Product noS2.45.A100.1880.6.70H.H.465.G.N.D 97632349
S pumps, range 70Product range
Standard range
* Without hose connection.** Installation type S and C pumps with discharge flange size 10" (DN 250) and higher are supplied with guide claw mounted on the flange.*** The horizontal base stand is included in the pump product number.
Pump type Pump
Accessories
*** Horizontal base stand
To be ordered separately
Vertical base stand ** Auto-coupling system
* Ring stand for portable use
S2.35.A80.1270.4.70H.S.340.G.N.D 97632322 - - 97506541 -S2.35.A80.1270.4.70H.C.340.G.N.D 97632323 - - 97506541 -S2.35.A80.1270.4.70H.D.340.G.N.D 97632324 - 96857815 - -S2.35.A80.1270.4.70H.H.340.G.N.D 97632325 96308212 - - -S2.40.A80.1270.4.70M.S.332.G.N.D 97632326 - - 97506541 -S2.40.A80.1270.4.70M.C.332.G.N.D 97632327 - - 97506541 -S2.40.A80.1270.4.70M.D.332.G.N.D 97632328 - 96857815 - -S2.40.A80.1270.4.70M.H.332.G.N.D 97632329 96308212 - - -S2.45.A100.1470.6.70H.S.443.G.N.D 97632330 - - 97510048 -S2.45.A100.1470.6.70H.C.443.G.N.D 97632331 - - 97510048 -S2.45.A100.1470.6.70H.D.443.G.N.D 97632332 - 96857816 - -S2.45.A100.1470.6.70H.H.443.G.N.D 97632333 96308192 - - -S2.55.A120.1470.6.70M.S.420.G.N.D 97632334 - - 97510049 -S2.55.A120.1470.6.70M.C.420.G.N.D 97632335 - - 97510049 -S2.55.A120.1470.6.70M.D.420.G.N.D 97632336 - 96857816 - -S2.55.A120.1470.6.70M.H.420.G.N.D 97632337 96308255 - - -S2.35.A80.1610.4.70H.S.361.G.N.D 97632338 - - 97506541 -S2.35.A80.1610.4.70H.C.361.G.N.D 97632339 - - 97506541 -S2.35.A80.1610.4.70H.D.361.G.N.D 97632340 - 96857815 - -S2.35.A80.1610.4.70H.H.361.G.N.D 97632341 96308212 - - -S2.40.A80.1610.4.70M.S.355.G.N.D 97632342 - - 97506541 -S2.40.A80.1610.4.70M.C.355.G.N.D 97632343 - - 97506541 -S2.40.A80.1610.4.70M.D.355.G.N.D 97632344 - 96857815 - -S2.40.A80.1610.4.70M.H.355.G.N.D 97632345 96308212 - - -S2.45.A100.1880.6.70H.S.465.G.N.D 97632346 - - 97510048 -S2.45.A100.1880.6.70H.C.465.G.N.D 97632347 - - 97510048 -S2.45.A100.1880.6.70H.D.465.G.N.D 97632348 - 96857816 - -S2.45.A100.1880.6.70H.H.465.G.N.D 97632349 96308192 - - -S2.45.A100.1070.8.70H.S.520.G.N.D 97632350 - - 97510048 -S2.45.A100.1070.8.70H.C.520.G.N.D 97632351 - - 97510048 -S2.45.A100.1070.8.70H.D.520.G.N.D 97632352 - 96857816 - -S2.45.A100.1070.8.70H.H.520.G.N.D 97632353 96308192 - - -S3.45.A200.1880.6.70L.S.371.G.N.D 97632354 - - 97510050 -S3.45.A200.1880.6.70L.C.371.G.N.D 97632355 - - 97510050 -S3.45.A200.1880.6.70L.D.371.G.N.D 97632356 - 96867808 - -S3.45.A200.1880.6.70L.H.371.G.N.D 97632357 96308192 - - -S3.45.A120.1880.6.70M.S.407.G.N.D 97632358 - - 97510049 -S3.45.A120.1880.6.70M.C.407.G.N.D 97632359 - - 97510049 -S3.45.A120.1880.6.70M.D.407.G.N.D 97632360 - 96857816 - -S3.45.A120.1880.6.70M.H.407.G.N.D 97632361 96308192 - - -S3.45.A200.1070.8.70L.S.402.G.N.D 97632362 - - 97510050 -S3.45.A200.1070.8.70L.C.402.G.N.D 97632363 - - 97510050 -S3.45.A200.1070.8.70L.D.402.G.N.D 97632364 - 96867808 - -S3.45.A200.1070.8.70L.H.402.G.N.D 97632365 96308192 - - -S3.45.A120.1070.8.70M.S.442.G.N.D 97632366 - - 97510049 -S3.45.A120.1070.8.70M.C.442.G.N.D 97632367 - - 97510049 -S3.45.A120.1070.8.70M.D.442.G.N.D 97632368 - 96857816 - -S3.45.A120.1070.8.70M.H.442.G.N.D 97632369 96308192 - - -
9
Product range S pumps, range 70
10
Standard pumps with stainless steel impeller
* Without hose connection.** Installation type S and C pumps with discharge flange size 10" (DN 250) and higher are supplied with guide claw mounted on the flange.*** The horizontal base stand is included in the pump product number.
Pump type Pump
Accessories
*** Horizontal base stand
To be ordered separatelyVertical base
stand** Auto-coupling
system* Ring stand for
portable useS2.40.A80.1270.4.70M.S.332.Q.N.D. 97647867 - - 97506541 -S2.40.A80.1270.4.70M.C.332.Q.N.D. 97647868 - - 97506541 -S2.40.A80.1270.4.70M.D.332.Q.N.D 97647869 - 96857815 - -S2.40.A80.1270.4.70M.H.332.Q.N.D 97647870 96308212 - - -S2.45.A100.1470.6.70H.S.443.Q.N.D 97647891 - - 97510048 -S2.45.A100.1470.6.70H.C.443.Q.N.D 97647892 - - 97510048 -S2.45.A100.1470.6.70H.D.443.Q.N.D 97647893 - 96857816 - -S2.45.A100.1470.6.70H.H.443.Q.N.D 97647894 96308192 - - -S2.55.A120.1470.6.70M.S.420.Q.N.D 97647895 - - 97510049 -S2.55.A120.1470.6.70M.C.420.Q.N.D 97647896 - - 97510049 -S2.55.A120.1470.6.70M.D.420.Q.N.D 97647897 - 96857816 - -S2.55.A120.1470.6.70M.H.420.Q.N.D 97647898 96308255 - - -S2.40.A80.1610.4.70M.S.355.Q.N.D 97647899 - - 97506541 -S2.40.A80.1610.4.70M.C.355.Q.N.D 97647900 - - 97506541 -S2.40.A80.1610.4.70M.D.355.Q.N.D 97647901 - 96857815 - -S2.40.A80.1610.4.70M.H.355.Q.N.D 97647902 96308212 - - -S2.45.A100.1880.6.70H.S.465.Q.N.D 97647903 - - 97510048 -S2.45.A100.1880.6.70H.C.465.Q.N.D 97647904 - - 97510048 -S2.45.A100.1880.6.70H.D.465.Q.N.D 97647905 - 96857816 - -S2.45.A100.1880.6.70H.H.465.Q.N.D 97647906 96308192 - - -S2.45.A100.1070.8.70H.S.520.Q.N.D 97647907 - - 97510048 -S2.45.A100.1070.8.70H.C.520.Q.N.D 97647908 - - 97510048 -S2.45.A100.1070.8.70H.D.520.Q.N.D 97647909 - 96857816 - -S2.45.A100.1070.8.70H.H.520.Q.N.D 97647910 96308192 - - -S3.45.A200.1880.6.70L.S.371.Q.N.D 97647911 - - 97510050 -S3.45.A200.1880.6.70L.C.371.Q.N.D 97647912 - - 97510050 -S3.45.A200.1880.6.70L.D.371.Q.N.D 97647913 - 96867808 - -S3.45.A200.1880.6.70L.H.371.Q.N.D 97647914 96308192 - - -S3.45.A120.1880.6.70M.S.407.Q.N.D 97647915 - - 97510049 -S3.45.A120.1880.6.70M.C.407.Q.N.D 97647916 - - 97510049 -S3.45.A120.1880.6.70M.D.407.Q.N.D 97647917 - 96857816 - -S3.45.A120.1880.6.70M.H.407.Q.N.D 97647918 96308192 - - -S3.45.A200.1070.8.70L.S.402.Q.N.D 97647919 - - 97510050 -S3.45.A200.1070.8.70L.C.402.Q.N.D 97647920 - - 97510050 -S3.45.A200.1070.8.70L.D.402.Q.N.D 97647921 - 96867808 - -S3.45.A200.1070.8.70L.H.402.Q.N.D 97647922 96308192 - - -S3.45.A120.1070.8.70M.S.442.Q.N.D 97647923 - - 97510049 -S3.45.A120.1070.8.70M.C.442.Q.N.D 97647924 - - 97510049 -S3.45.A120.1070.8.70M.D.442.Q.N.D 97647925 - 96857816 - -S3.45.A120.1070.8.70M.H.442.Q.N.D 97647926 96308192 - - -S2.35.A80.1270.4.70H.S.340.Q.N.D 97654029 - - 97506541 -S2.35.A80.1270.4.70H.C.340.Q.N.D 97654030 - - 97506541 -S2.35.A80.1270.4.70H.D.340.Q.N.D 97654031 - 96857815 - -S2.35.A80.1270.4.70H.H.340.Q.N.D 97654032 96308212 - - -S2.35.A80.1610.4.70H.S.361.Q.N.D 97654033 - - 97506541 -S2.35.A80.1610.4.70H.C.361.Q.N.D 97654034 - - 97506541 -S2.35.A80.1610.4.70H.D.361.Q.N.D 97654035 - 96857815 - -S2.35.A80.1610.4.70H.H.361.Q.N.D 97654036 96308212 - - -
Product range S pumps, range 70
Explosion-proof pumps
* Without hose connection.** Installation type S and C pumps with discharge flange size 10" (DN 250) and higher are supplied with guide claw mounted on the flange.*** The horizontal base stand is included in the pump product number.
Pump type Pump
Accessories
*** Horizontal base stand
To be ordered separatelyVertical base
stand** Auto-coupling
system* Ring stand for
portable useS2.35.A80.1270.4.70H.S.340.G.Ex.D 97660727 - - 97506541 -S2.35.A80.1270.4.70H.C.340.G.Ex.D 97660728 - - 97506541 -S2.35.A80.1270.4.70H.D.340.G.Ex.D 97660729 - 96857815 - -S2.35.A80.1270.4.70H.H.340.G.Ex.D 97660730 96308212 - - -S2.40.A80.1270.4.70M.S.332.G.Ex.D 97660771 - - 97506541 -S2.40.A80.1270.4.70M.C.332.G.Ex.D 97660772 - - 97506541 -S2.40.A80.1270.4.70M.D.332.G.Ex.D 97660773 - 96857815 - -S2.40.A80.1270.4.70M.H.332.G.Ex.D 97660774 96308212 - - -S2.45.A100.1470.6.70H.S.443.G.Ex.D 97660775 - - 97510048 -S2.45.A100.1470.6.70H.C.443.G.Ex.D 97660776 - - 97510048 -S2.45.A100.1470.6.70H.D.443.G.Ex.D 97660777 - 96857816 - -S2.45.A100.1470.6.70H.H.443.G.Ex.D 97660779 96308192 - - -S2.55.A120.1470.6.70M.S.420.G.Ex.D 97660780 - - 97510049 -S2.55.A120.1470.6.70M.C.420.G.Ex.D 97660781 - - 97510049 -S2.55.A120.1470.6.70M.D.420.G.Ex.D 97660782 - 96857816 - -S2.55.A120.1470.6.70M.H.420.G.Ex.D 97660783 96308255 - - -S2.35.A80.1610.4.70H.S.361.G.Ex.D 97660784 - - 97506541 -S2.35.A80.1610.4.70H.C.361.G.Ex.D 97660785 - - 97506541 -S2.35.A80.1610.4.70H.D.361.G.Ex.D 97660786 - 96857815 - -S2.35.A80.1610.4.70H.H.361.G.Ex.D 97660787 96308212 - - -S2.40.A80.1610.4.70M.S.355.G.Ex.D 97660788 - - 97506541 -S2.40.A80.1610.4.70M.C.355.G.Ex.D 97660789 - - 97506541 -S2.40.A80.1610.4.70M.D.355.G.Ex.D 97660790 - 96857815 - -S2.40.A80.1610.4.70M.H.355.G.Ex.D 97660791 96308212 - - -S2.45.A100.1880.6.70H.S.465.G.Ex.D 97660792 - - 97510048 -S2.45.A100.1880.6.70H.C.465.G.Ex.D 97660793 - - 97510048 -S2.45.A100.1880.6.70H.D.465.G.Ex.D 97660794 - 96857816 - -S2.45.A100.1880.6.70H.H.465.G.Ex.D 97660795 96308192 - - -S2.45.A100.1070.8.70H.S.520.G.Ex.D 97660796 - - 97510048 -S2.45.A100.1070.8.70H.C.520.G.Ex.D 97660797 - - 97510048 -S2.45.A100.1070.8.70H.D.520.G.Ex.D 97660798 - 96857816 - -S2.45.A100.1070.8.70H.H.520.G.Ex.D 97660799 96308192 - - -S3.45.A200.1880.6.70L.S.371.G.Ex.D 97660800 - - 97510050 -S3.45.A200.1880.6.70L.C.371.G.Ex.D 97660801 - - 97510050 -S3.45.A200.1880.6.70L.D.371.G.Ex.D 97660802 - 96867808 - -S3.45.A200.1880.6.70L.H.371.G.Ex.D 97660803 96308192 - - -S3.45.A120.1880.6.70M.S.407.G.Ex.D 97660804 - - 97510049 -S3.45.A120.1880.6.70M.C.407.G.Ex.D 97660805 - - 97510049 -S3.45.A120.1880.6.70M.D.407.G.Ex.D 97660806 - 96857816 - -S3.45.A120.1880.6.70M.H.407.G.Ex.D 97660807 96308192 - - -S3.45.A200.1070.8.70L.S.402.G.Ex.D 97660808 - - 97510050 -S3.45.A200.1070.8.70L.C.402.G.Ex.D 97660809 - - 97510050 -S3.45.A200.1070.8.70L.D.402.G.Ex.D 97660810 - 96867808 - -S3.45.A200.1070.8.70L.H.402.G.Ex.D 97660811 96308192 - - -S3.45.A120.1070.8.70M.S.442.G.Ex.D 97660812 - - 97510049 -S3.45.A120.1070.8.70M.C.442.G.Ex.D 97660813 - - 97510049 -S3.45.A120.1070.8.70M.D.442.G.Ex.D 97660814 - 96857816 - -S3.45.A120.1070.8.70M.H.442.G.Ex.D 97660815 96308192 - - -
11
Product range S pumps, range 70
12
Explosion proof pumps with stainless steel impeller
* Without hose connection.** Installation type S and C pumps with discharge flange size 10" (DN 250) and higher are supplied with guide claw mounted on the flange.*** The horizontal base stand is included in the pump product number.
Pump type Pump
Accessories
*** Horizontal base stand
To be ordered separatelyVertical base
stand** Auto-coupling
system* Ring stand for
portable useS2.35.A80.1270.4.70H.S.340.Q.Ex.D 97663765 - - 97506541 -S2.35.A80.1270.4.70H.C.340.Q.Ex.D 97663766 - - 97506541 -S2.35.A80.1270.4.70H.D.340.Q.Ex.D 97663767 - 96857815 - -S2.35.A80.1270.4.70H.H.340.Q.Ex.D 97663768 96308212 - - -S2.40.A80.1270.4.70M.S.332.Q.Ex.D 97663769 - - 97506541 -S2.40.A80.1270.4.70M.C.332.Q.Ex.D 97663770 - - 97506541 -S2.40.A80.1270.4.70M.D.332.Q.Ex.D 97663771 - 96857815 - -S2.40.A80.1270.4.70M.H.332.Q.Ex.D 97663772 96308212 - - -S2.45.A100.1470.6.70H.S.443.Q.Ex.D 97663773 - - 97510048 -S2.45.A100.1470.6.70H.C.443.Q.Ex.D 97663774 - - 97510048 -S2.45.A100.1470.6.70H.D.443.Q.Ex.D 97663775 - 96857816 - -S2.45.A100.1470.6.70H.H.443.Q.Ex.D 97663776 96308192 - - -S2.55.A120.1470.6.70M.S.420.Q.Ex.D 97663777 - - 97510049 -S2.55.A120.1470.6.70M.C.420.Q.Ex.D 97663778 - - 97510049 -S2.55.A120.1470.6.70M.D.420.Q.Ex.D 97663779 - 96857816 - -S2.55.A120.1470.6.70M.H.420.Q.Ex.D 97663780 96308255 - - -S2.35.A80.1610.4.70H.S.361.Q.Ex.D 97663781 - - 97506541 -S2.35.A80.1610.4.70H.C.361.Q.Ex.D 97663782 - - 97506541 -S2.35.A80.1610.4.70H.D.361.Q.Ex.D 97663783 - 96857815 - -S2.35.A80.1610.4.70H.H.361.Q.Ex.D 97663784 96308212 - - -S2.40.A80.1610.4.70M.S.355.Q.Ex.D 97663785 - - 97506541 -S2.40.A80.1610.4.70M.C.355.Q.Ex.D 97663786 - - 97506541 -S2.40.A80.1610.4.70M.D.355.Q.Ex.D 97663787 - 96857815 - -S2.40.A80.1610.4.70M.H.355.Q.Ex.D 97663788 96308212 - - -S2.45.A100.1880.6.70H.S.465.Q.Ex.D 97663789 - - 97510048 -S2.45.A100.1880.6.70H.C.465.Q.Ex.D 97663790 - - 97510048 -S2.45.A100.1880.6.70H.D.465.Q.Ex.D 97663791 - 96857816 - -S2.45.A100.1880.6.70H.H.465.Q.Ex.D 97663792 96308192 - - -S2.45.A100.1070.8.70H.S.520.Q.Ex.D 97663793 - - 97510048 -S2.45.A100.1070.8.70H.C.520.Q.Ex.D 97663794 - - 97510048 -S2.45.A100.1070.8.70H.D.520.Q.Ex.D 97663795 - 96857816 - -S2.45.A100.1070.8.70H.H.520.Q.Ex.D 97663796 96308192 - - -S3.45.A200.1880.6.70L.S.371.Q.Ex.D 97663797 - - 97510050 -S3.45.A200.1880.6.70L.C.371.Q.Ex.D 97663798 - - 97510050 -S3.45.A200.1880.6.70L.D.371.Q.Ex.D 97663799 - 96867808 - -S3.45.A200.1880.6.70L.H.371.Q.Ex.D 97663800 96308192 - - -S3.45.A120.1880.6.70M.S.407.Q.Ex.D 97663801 - - 97510049 -S3.45.A120.1880.6.70M.C.407.Q.Ex.D 97663802 - - 97510049 -S3.45.A120.1880.6.70M.D.407.Q.Ex.D 97663803 - 96857816 - -S3.45.A120.1880.6.70M.H.407.Q.Ex.D 97663804 96308192 - - -S3.45.A200.1070.8.70L.S.402.Q.Ex.D 97663805 - - 97510050 -S3.45.A200.1070.8.70L.C.402.Q.Ex.D 97663806 - - 97510050 -S3.45.A200.1070.8.70L.D.402.Q.Ex.D 97663807 - 96867808 - -S3.45.A200.1070.8.70L.H.402.Q.Ex.D 97663808 96308192 - - -S3.45.A120.1070.8.70M.S.442.Q.Ex.D 97663809 - - 97510049 -S3.45.A120.1070.8.70M.C.442.Q.Ex.D 97663810 - - 97510049 -S3.45.A120.1070.8.70M.D.442.Q.Ex.D 97663811 - 96857816 - -S3.45.A120.1070.8.70M.H.442.Q.Ex.D 97663812 96308192 - - -
S pumps, range 70
13
Variants
List of variantsMotor
Various cable lengths82 ft (25 m)
165 ft (50 m)
EMC power cables Screened power cables for variable speed drives
33 ft (10 m)50 ft (15 m)82 ft (25 m)
165 ft (50 m)Special motor Special voltagePTC thermistors in windingsSpecial oil Non-toxic Shell Ondina 917
Motor protectionPTC + moisture switch FPV1Klixon + moisture switch + WIO FPV2aPTC + moisture switch + WIO FPV2bKlixon + moisture switch + WIO + PT100 at lower and upper bearing + PVS 3 FPV4aPTC + moisture switch + WIO + PT100 at lower and upper bearing + PVS 3 FPV4b
MaterialsStainless steel lifting bracket AISI 316Stainless steel impeller Variant QStainless steel impeller and pump housing Variant SStainless steel Impeller, pump housing and motor housing Variant R
Tests
Test at specified duty on standard impeller curve
Trimmed impeller for specified duty test Additional test of entire QH curve (incl. report) 5-10 flows from pump performance curve
Different test standard Efficiency guaranteed by GrundfosISO 9906 grade 1 tolerancesISO 9906 grade 2 tolerances
Vibration test (incl. report) According to Grundfos factory quality standardPerformance test on dry test stand Not yet availableNPSHr test Not yet availableString test Contact GrundfosWitness test Contact Grundfos
MiscellaneousSpecial packaging Contact GrundfosSpecial nameplate Contact GrundfosOther variants Contact Grundfos
14
S pumps, range 70Construction
Sectional drawings, motors
Fig. 4 Non-explosion-proof motor without cooling jacket
TM04
261
1 27
08
Construction S pumps, range 70
Fig. 5 Non-explosion-proof motor with cooling jacket
TM04
261
2 27
08
15
Construction S pumps, range 70
16
Fig. 6 Explosion-proof motor without cooling jacket
TM04
261
3 27
08
Construction S pumps, range 70
18
Sectional drawings, pumps
Fig. 8 Submerged installation pump with cooling jacket
TM04
258
9 27
08
Construction S pumps, range 70
20
Fig. 10 Installation type S pump on auto coupling
TM04
270
8 28
08
Construction S pumps, range 70
22
Fig. 12 Dry, horizontal installation type H pump
TM04
259
0 27
08TM
04 2
591
2708
Construction S pumps, range 70
Components and material specification
Motor
Pump
Accessories
* Ex versions have cast iron cable entry and two moisture switches.** Available of stainless steel (custom-built option).
Pos. Component Material (AISI/DIN W.-Nr.)7a Rivet Stainless steel (316/1.4436)
25a Screw Stainless steel (316/1.4436)
25 Pressure test plug Stainless steel (316/1.4436)
48 Stator lamination
**55 Stator housing Cast iron (EN-JL 1040/A48 30)
58 Seal housing Cast iron
60 Bearing bracket cover Cast iron
61c Upper bearing bracket Cast iron
72a O-ring NBR rubber
72 O-ring NBR rubber
76a Approval plate
100 O-ring NBR rubber
105b Mechanical seal SiC/SiC or SiC/carbon
105 Mechanical seal SiC/SiC or SiC/carbon
150c Cooling jacket Galvanised steel
153 Ball bearing Stainless steel
154 Ball bearing Stainless steel
**155 Lower bearing bracket Cast iron
157b O-ring NBR rubber
157 O-ring NBR rubber
**164a Motor top cover Cast iron
*168 Cable entry PA or cast iron
172 Shaft with rotor Stainless steel (329/1.4462)
173b Earth terminal
173c Washer Stainless steel (316/1.4436)
173e Screw Stainless steel (316/1.4436)
173f Spring washer Stainless steel (316/1.4436)
173g Earth connector
173 Screw Stainless steel (316/1.4436)
176a Terminal block
176b Screw Stainless steel (316/1.4436)
176c Terminal block
176d Terminal block
178 Screw Stainless steel (316/1.4436)
180 Cable clamp PA or cast iron
181a Screw Stainless steel (316/1.4436)
181 Cable ATON
182b Hexagon socket head cap screw Stainless steel (316/1.4436)
184b Screw Stainless steel (316/1.4436)
184 Screw Stainless steel (316/1.4436)
187a Washer Stainless steel (316/1.4436)
187 Circlip
188 Circlip
190 Lifting bracket Stainless steel (316/1.4408)
193 Plug Stainless steel (316/1.4408)
194 O-ring NBR rubber
197 Washer Stainless steel (316/1.4436)
198 Rubber seal
248 Screw Stainless steel (316/1.4436)
250a Cable entry PA or cast iron
250b Rubber seal
250 Cable clamp PA or cast iron
252 Cable ATON
520a Screw Stainless steel (316/1.4436)
520b Nut Stainless steel (316/1.4436)
*520 Moisture switch
522 Holder
Pos. Component Material (AISI/DIN W.-Nr.)7a Rivet
9a Key (for keyway) Stainless steel (316/1.4436)
12c Adjusting screw Stainless steel (316/1.4436)
26 Screw Stainless steel (316/1.4436)
37 O-ring NBR rubber
37b O-ring NBR rubber
**49 Impeller Cast iron EN-JL 1050
**50 Volute casing Cast iron EN-JS 1050
67 Impeller screw Stainless steel (316/1.4436)
76 Nameplate
301 Motor housing
494 Plug Stainless steel (316/1.4436)
495 O-ring NBR rubber
Pos. Component Material
**701 Auto-coupling base unit Cast iron
**702 Guide rail bracket Cast iron
**703 Guide claw Cast iron
749 Bend Cast iron
**761 Hose connector Cast iron or stainless steel
762 Base plate Cast iron or steel
487 Base stand, horizontal Galvanised steel
799 Anchor bolt
Pos. Component Material (AISI/DIN W.-Nr.)
23
24
S pumps, range 70Product description
FeaturesSmartTrimOn conventional pumps, maintaining factory-set impeller clearance is a time-consuming and costly task. The pumps need to be disconnected from the pipework and to be totally dismantled, and new parts need to be mounted in order to maintain full pumping efficiency. Not so with Grundfos SmartTrim!
All Grundfos heavy-duty channel-impeller pumps, whether for submerged or dry installation, are equipped with the unique SmartTrim impeller clearance adjustment system. This enables you to easily restore factory-set impeller clearance and maintain peak pumping efficiency. All you need to do is to tighten the adjustment screws on the exterior of the impeller housing. This can be done on site, quickly and easily, without dismantling the pump and without using special tools.
A: With Grundfos SmartTrim impeller clearance adjustment system
B: Without impeller clearance adjustment system
SmartSealFor pumps with 10" discharge or larger, the Grundfos SmartSeal auto-coupling gasket mounted on the pump discharge flange provides a completely leak-proof connection between the pump and the base unit of the auto-coupling system. This optimises the efficiency of the entire pumping system and keeps operating costs at a minimum.
Ball bearingsThe bearings are greased for life.
Main bearings: Double-row angular contact ball bearing
Support bearings: Single-row deep-groove ball bearing.
Shaft sealThe pumps have a shaft seal consisting of a primary and a secondary shaft seal.
The material combination of the primary shaft seal of all pump types is silicon carbide/silicon carbide. For the secondary shaft seal, the mateial combination is silicon carbide/carbon.
The shaft seals are placed in the oil chamber of the pump. The oil chamber provides reliable sealing between the pumped liquid and the motor.
The shaft seals have no springs or other parts in direct contact with the pumped liquid. This prevents rags and fibres from getting caught. The shaft seals are bidirectional, meaning that they can operate in either direction thus allowing for opposite rotation caused by back-flow of liquid through the pump.
MotorThe motor is a watertight, totally encapsulated motor with:
• insulation class H (356 °F (180 °C))• temperature rise class F (221 °F (105 °C))• enclosure class IP68.For motor protection and sensors, see section Sensors below.
Power cablesThe pumps have H07RN-F AT cables as standard or screened ATON EMC VSCCB cables on request.
The cables are 40 ft (15 m) long as standard. Other cable lengths are available on request. See section List of variants on page 13.
The number and dimension of cables depend on the motor size.
Standard cable
TM04
239
1 25
08
Factory-set impeller clearance
Efficiency drop in %
Years
B
A
0
3
6
9
12
15
1 2 3 4 5
Cable Motor power [hp (kW])2 x 4 x 25 mm2 + 7 x 1.5 mm2 107 - 127 (80 - 95)
2 x 4 x 35 mm2 + 7 x 1.5 mm2 127 - 147 (95 - 110)
2 x 4 x 50 mm2 + 7 x 1.5 mm2 147 (110)
2 x 4 x 70 mm2 + 7 x 1.5 mm2 188 (140)
Cable type[mm2]
Outer cable diameter[inch (mm)]
Bending radius
min. max. [inch (mm)]4 x 25 1.14 (28.9) 1.23 (31.4) 7.5 (190)4 x 35 1.28 (32.5) 1.37 (34.7) 8.7 (220)4 x 50 1.48 (37.7) 1.59 (40.4) 9.8 (250)4 x 70 1.68 (42.7) 1.79 (45.4) 11 (280)
Product description S pumps, range 70
EMC cable
Control cable
Cable entryWatertight PA or cast iron cable entry with soft shape and sealing rings to prevent damage of the cable or leaks.
SensorsAs standard the pump is equipped with:
• Three thermal switches (Klixon), one in each phase.• One moisture switch in terminal block.
Customised sensor options1. WIO (water-in-oil) sensor
The WIO sensor measures the water content in the oil and converts the value into an analogue current signal. The two sensor conductors are for power supply as well as for carrying the signal to the mea-suring device or controller. The sensor measures the water content from 0 to 20 %. It also sends a signal if the water content is outside the normal range (warning), or if there is air in the oil chamber (alarm). The sensor is fitted in a stainless steel tube for mechanical protection.The WIO sensor is connected to the Grundfos IO 111 module.
2. PVS 3 (pump vibration sensor)The vibration sensor monitors the vibration level of the pump. A change in the vibration level indicates an abnormal situation. The cause of this can be a clogged impeller, worn bearings, closed discharge valve, etc., indicating that service inspection should be carried out now in order to protect the pump or the pipe system from being damaged.
3. Bearing temperature sensor.
TestingAll pumps are tested before leaving the factory. The factory test report is based on ANSI-HI centrifugal pump test 1.6-2000, Acceptance level B. Test reports can be ordered directly with the pump or can be ordered separately based on the pump serial number.
Other tests or third party inspection certificates are available on request including HI B & A standards. See section List of variants on page 13.
Operating conditionsPumps without cooling jacket in submerged installation:• Continuous operation when pump is fully sub-
merged to top of motor.• Intermittent operation with max. 20 starts per hour
when pump is submerged to middle of motor and with short periods of operation down to the top of the pump housingNote: Explosion proof pumps must always be fully submerged
Pumps with cooling jacket in submerged and dry installation:• Continuous and intermittent operation with max. 20
starts per hour with water level down to the top of the pump housing.
Pumped liquidspH value: 4-10
Liquid temperature: 32 °F - 104 °F (0 °C - +40 °C)
When pumping liquids with a density and/or a kinematic viscosity higher than that of water, use motors with correspondingly higher outputs.
Sound pressureThe sound pressure level of the pump is lower than the limiting values stated in the EC Council directive 2006/42/EC relating to machinery (the EC Machinery Directive).
Motor range
Cable type[mm2]
Outer cable diameter[inch (mm)]
Bending radius
min. max. [inch (mm)]3 x 35 1.11 (28.3) 1 23 (31.3) 6.2 (157)3 x 70 1.52 (38.7) 1.64 (41.7) 8.2 (209)
Cable type[mm2]
Outer cable diameter[inch (mm)]
Bending radius
min. max. [inch (mm)]
7 x 1.5 0.57(14.4)
0.63 - 0.65(16.0 - 16.4)
4(100)
Shaft power [hp (kW)] No. of poles107 (80) 8127 (95) 4147 (110) 6188 (140) 6
25
Product description S pumps, range 70
26
Explosion-proof pumps
Approval standardsThese pumps are approved by FM according to FM3600, FM3615 and FM3615.80.
Explanation to FM approvalThe S pumps have the following explosion protection classification: Class I, Division 1, Groups C and D, T4, T3, IP68
Pump controllersS pumps, range 70, can be controlled by Grundfos Dedicated Controls (DC).
The Grundfos Dedicated Controls system can can control from one to six pumps.
The Dedicated Controls system starts/stops the S pumps by means of:
• float switches• pressure sensor• ultrasonic sensor.Furthermore, it is possible to control the water level by both float switches and an analog pressure sensor or ultrasonic sensor.
Optionally, it can control a mixer and/or a flush valve. The Dedicated Controls system can be extended with an IO 111 module per pump (for S pumps with built-in analog sensor).
For further settings, see the installation and operating instructions for the pump controller selected.
Standards Code Description
FM3600FM3615FM3615.80
Class I Explosive atmosphere is caused by gas or vapours.
Division 1 Area classification
Groups C and D
Classification of gases
T4/T3 Maximum surface temperature is 275 °F (35 °C) and 392 °F (200 °C)
IP68 Enclosure class according to IEC 60529.
Product description S pumps, range 70
Wiring diagrams
Fig. 13 Wiring diagrams, Y-connected (460 V)
TM04
671
9 0
810
Sens
ors
Ther
mal
sw
itch
Moi
stur
e sw
itche
s
PT1
00 lo
wer
bea
ring
PT1
00 s
tato
r
Ther
mis
tor
Pow
er c
able M
otor
27
28
S pumps, range 70Curve charts and technical data
The following many pages are divided into sections:
How to read the curve charts
Pages 28-29 A brief explanation of how to read the curve charts, the curve conditions, etc.
Performance curves and technical data:Page 30 Low pressurePage 32 Medium pressurePage 36 High pressure
TM04
208
9 19
08
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
0
20
40
60
80
100
120
140
160
180
200
[ft]H
0 100 200 300 400 500 600 Q [l/s]
0
10
20
30
40
50
60
[m]H
0
10
20
30
40
[ft]NPSH
70M.S
60 Hz
ISO 9906 Annex A
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
60
80
100
120
140
160
[hp]
P2
60
80
100
120
[kW]
P2
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
Pump type:
70: range 70M: Pressure range (Medium pressure)S: Installation type
Total pump head H = Htotal
The power curves indicate shaft power [P2] for the pumps shown
Max. efficiency mark
QH curve for the individual pump.
NPSH curve for all variants shown. When sizing the pumps, add a safety margin of at least 1.6 ft (0.5 m).
Curve charts and technical data
S pumps, range 70
Curve conditionsThe guidelines below apply to the curves shown in the performance charts on page 30 to page 38.
• ANSI-HI centrifugal pump test 1.6-2000, Accep-tance level B.
• The curves show pump performance with different impeller diameters at rated speed.
• The bold part of the curves show the recom-mended operating range.
• The curves apply to the pumping of airless water at a temperature of 68 °F (+20 °C) and a kinematic vis-cosity of 1 cSt (1 mm2/s).
• NPSH: The curves show average values measured under the same conditions as the performance curves.When dimensioning the pump, add a safety margin of at least 1.6 ft (0.5 m).
• In case of other densities than 133.5 ounces/gallon (1000 kg/m3), the discharge pressure is proportional to the density.
• When pumping liquids with a density higher than 133.5 ounces/gallon (1000 kg/m3), motors with cor-respondingly higher outputs must be used.
Calculation of total headThe total pump head consists of the height difference between the measuring points + the differential head + the dynamic head.
Performance testsThe requested duty point for every pump is tested according to ISO 9906, Annex A, and without certifica-tion.
In case of pumps ordered on the basis of impeller diam-eter only (no requested duty point), the pump will be tested close to the best efficiency point (BEP) of the published performance curve which is related to the ordered impeller diameter (according to ISO 9906, Annex A).
If the customer requires either more points on the curve to be checked or certain minimum performances or cer-tificates, individual measurements must be made, and a certificate can be ordered.
CertificatesCertificates have to be confirmed for every order and are available on request as follows:
• Certificate of compliance with the order (EN 10204 - 2.1)
• Pump test sheet.
Witness testWhen the pumps are being tested or are tested with a certification it is possible for the customer to witness the testing procedure according to ISO 9906.
The witness test is not a certificate and will not result in a written statement from Grundfos. The witness itself is the only guarantee that everything is carried out as pre-scribed in the testing procedure.
If the customer wants to witness test the pump perfor-mance, place this request on the order.
Hgeo: Height difference between measuring points.
Hstat: Differential head between suction and the dis-charge side of the pump.
Hdyn: Calculated values based on the velocity of the pumped liquid on the suction and the discharge side of the pump.
Htotal Hgeo Hstat Hdyn+ +=
29
30
S pumps, range 70Performance curvesTechnical data
S 70 low pressure, 6- and 8-pole
S3.45.A200.1070 and S3.45.A200.1880
TM04
659
9 06
10TM
04 6
600
0610
3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 14000 Q [US GPM]
0
10
20
30
40
50
60
70
80
[ft]H
200 300 400 500 600 700 800 900 Q [l/s]
0
5
10
15
20
25
[m]H
0
10
20
30
40
[ft]NPSH
70L.S
60 Hz
ISO 9906 Annex A
S3.45.A200.1880.6.
S3.45.A200.1070.8.
S3.45.A200.1880.6.
S3.45.A200.1070.8.
3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 14000 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S3.45.A200.1880.6.
S3.45.A200.1070.8.
3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 14000 Q [US GPM]
0
10
20
30
40
50
60
70
80
[ft]H
200 300 400 500 600 700 800 900 Q [l/s]
0
5
10
15
20
25
[m]H
0
10
20
30
40
[ft]NPSH
70L.C/D/H
60 Hz
ISO 9906 Annex A
S3.45.A200.1880.6.
S3.45.A200.1070.8.
S3.45.A200.1880.6.
S3.45.A200.1070.8.
3000 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 14000 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S3.45.A200.1880.6.
S3.45.A200.1070.8.
Performance curves Technical data
S pumps, range 70
Electrical data
Note: Enclosure class: IP68
Pump data
* With 50 ft (15 m) cable
Pump type P1 [kW]
P2 [hp]
No. of poles RPM Starting
method
IN Istart ηmotor [%] Cos φ Moment of inertia
[lbft2 (kgm2]
Breakdown torque Mmax [lbf*ft (Nm)][A] [A] 1/2 3/4 1/1 1/2 3/4 1/1
S3.45.A200.1880.6.70L 152 188 6 1186 Y/D 242 1978 92 92 92 0.63 0.73 0.79 66.4 (2.8) 2161 (2930)
S3.45.A200.1070.8.70L 86 107 8 882 Y/D 129 861 93 94 93 0.77 0 83 0.84 49.8 (2.1) 1600.5 (2170)
Pump typeMax. solids size Max. installation depth Weight *
[inch (mm)] [feet (m)] [lbs (kg)]S3.45.A200.1880.6.70L.S 4.5 (115) 66 (20) 3571 (1620)S3.45.A200.1880.6.70L.C 4.5 (115) 66 (20) 3924 (1780)S3.45.A200.1880.6.70L.D 4.5 (115) 66 (20) 3571 (1620)S3.45.A200.1880.6.70L.H 4.5 (115) 66 (20) 3571 (1620)S3.45.A200.1070.8.70L.S 4.5 (115) 66 (20) 3307 (1500)S3.45.A200.1070.8.70L.C 4.5 (115) 66 (20) 3638 (1650)S3.45.A200.1070.8.70L.D 4.5 (115) 66 (20) 3307 (1500)S3.45.A200.1070.8.70L.H 4.5 (115) 66 (20) 3307 (1500)
31
Performance curves Technical data
S pumps, range 70
32
S 70 medium pressure, 4- and 6-pole
S2.40.A80.1270, S2.55.A120.1470 and S2.40.A80.1610
TM04
660
1 10
10TM
04 6
602
0610
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
0
20
40
60
80
100
120
140
160
180
200
[ft]H
0 100 200 300 400 500 600 Q [l/s]
0
10
20
30
40
50
60
[m]H
0
10
20
30
40
[ft]NPSH
70M.S
60 Hz
ISO 9906 Annex A
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
60
80
100
120
140
160
[hp]
P2
60
80
100
120
[kW]
P2
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
0
20
40
60
80
100
120
140
160
180
200
[ft]H
0 100 200 300 400 500 600 Q [l/s]
0
10
20
30
40
50
60
[m]H
0
10
20
30
40
[ft]NPSH
70M.C/D/H
60 Hz
ISO 9906 Annex A
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 1000Q [US GPM]
60
80
100
120
140
160
[hp]
P2
60
80
100
120
[kW]
P2
S2.55.A120.1470.6.
S2.40.A80.1270.4.
S2.40.A80.1610.4.
Performance curves Technical data
S pumps, range 70
Electrical data
Note: Enclosure class: IP68
Pump data
* With 50 ft (15 m) cable
Pump type P1 [kW]
P2 [hp]
No. of poles RPM Starting
method
IN Istart ηmotor [%] Cos φ Moment of inertia
[lbft2 (kgm2]
Breakdown torque Mmax [lbf*ft (Nm)][A] [A] 1/2 3/4 1/1 1/2 3/4 1/1
S2.40.A80.1270.4.70M 103 127 4 1778 Y/D 148 1105 94 94 92 0.80 0.86 0.88 20.2 (0.85) 1090.9 (1479)S2.55.A120.1470.6.70M 118 147 6 1181 Y/D 175 1275 91 93 93 0.73 0.81 0.85 49.8 (2.1) 1639.6 (2223)S2.40.A80.1610.4.70M 129 161 4 1778 Y/D 185 1380 94 94 93 0.77 0.85 0.88 26.1 (1.1) 1427.2 (1935)
Pump typeMax. solids size Max. installation depth Weight *
[inch (mm)] [feet (m)] [lbs (kg)]S2.40.A80.1270.4.70M.S 4 (100) 66 (20) 2425 (1100)S2.40.A80.1270.4.70M.C 4 (100) 66 (20) 2668 (1210)S2.40.A80.1270.4.70M.D 4 (100) 66 (20) 2910 (1320)S2.40.A80.1270.4.70M.H 4 (100) 66 (20) 2910 (1320)S2.55.A120.1470.6.70M.S 5.5 (140) 66 (20) 2866 (1300)S2.55.A120.1470.6.70M.C 5.5 (140) 66 (20) 3153 (1430)S2.55.A120.1470.6.70M.D 5.5 (140) 66 (20) 3439 (1560)S2.55.A120.1470.6.70M.H 5.5 (140) 66 (20) 3439 (1560)S2.40.A80.1610.4.70M.S 4 (100) 66 (20) 2315 (1050)S2.40.A80.1610.4.70M.C 4 (100) 66 (20) 2557 (1160)S2.40.A80.1610.4.70M.D 4 (100) 66 (20) 2778 (1260)S2.40.A80.1610.4.70M.H 4 (100) 66 (20) 2778 (1260)
33
Performance curves Technical data
S pumps, range 70
34
S 70 medium pressure, 6- and 8-pole
S3.45.A120.1070 and S3.45.A120.1880
TM04
660
3 06
10TM
04 6
604
0610
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 Q [US GPM]
0
10
20
30
40
50
60
70
80
90
100
[ft]H
0 100 200 300 400 500 600 700 Q [l/s]
0
5
10
15
20
25
30
[m]H
0
10
20
30
40
[ft]NPSH
70M.S
60 Hz
ISO 9906 Annex A
S3.45.A120.1880.6.
S3.45.A120.1070.8.
S3.45.A120.1880.6.
S3.45.A120.1070.8.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 Q [US GPM]
60
80
100
120
140
160
180
[hp]
P2
60
80
100
120
[kW]
P2
S3.45.A120.1880.6.
S3.45.A120.1070.8.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 Q [US GPM]
0
10
20
30
40
50
60
70
80
90
100
[ft]H
0 100 200 300 400 500 600 700 Q [l/s]
0
5
10
15
20
25
30
[m]H
0
10
20
30
40
[ft]NPSH
70M.C/D/H
60 Hz
ISO 9906 Annex A
S3.120.300.1400.6.
S3.120.300.800.8.
S3.120.300.1400.6.
S3.120.300.800.8.
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 Q [US GPM]
60
80
100
120
140
160
180
[hp]
P2
60
80
100
120
[kW]
P2
S3.120.300.1400.6.
S3.120.300.800.8.
Performance curves Technical data
S pumps, range 70
Electrical data
Note: Enclosure class: IP68
Pump data
* With 50 ft (15 m) cable
Pump type P1 [kW]
P2 [hp]
No. of poles RPM Starting
method
IN Istart ηmotor [%] Cos φ Moment of inertia
[lbft2 (kgm2]
Breakdown torque Mmax [lbf*ft (Nm)][A] [A] 1/2 3/4 1/1 1/2 3/4 1/1
S3.45.A120.1880.6.70M 152 188 6 1186 Y/D 242 1978 92 92 92 0.63 0.73 0.79 66.4 (2.8) 2161 (2930)S3.45.A120.1070.8.70M 86 107 8 882 Y/D 129 861 93 94 93 0.77 0 83 0.84 49.8 (2.1) 1600.5 (2170)
Pump typeMax. solids size Max. installation depth Weight *
[inch (mm)] [feet (m)] [lbs (kg)]S3.45.A120.1880.6.70M.S 4.5 (115) 66 (20) 3131 (1420)S3.45.A120.1880.6.70M.C 4.5 (115) 66 (20) 3439 (1560)S3.45.A120.1880.6.70M.D 4.5 (115) 66 (20) 3748 (1700)S3.45.A120.1880.6.70M.H 4.5 (115) 66 (20) 3748 (1700)S3.45.A120.1070.8.70M.S 4.5 (115) 66 (20) 2866 (1300)S3.45.A120.1070.8.70M.C 4.5 (115) 66 (20) 3153 (1430)S3.45.A120.1070.8.70M.D 4.5 (115) 66 (20) 3439 (1560)S3.45.A120.1070.8.70M.H 4.5 (115) 66 (20) 3439 (1560)
35
Performance curves Technical data
S pumps, range 70
36
S 70 high pressure, 4-pole
S2.35.A80.1270 and S2.35.A80.1610
TM04
659
5 06
10
0 400 800 1200 1600 2000 2400 2800 Q [US GPM]
0
40
80
120
160
200
240
280
[ft]H
0 50 100 150 200 Q [l/s]
0
20
40
60
80
[m]H
0
10
20
30
40
[ft]NPSH
70H.S
60 Hz
ISO 9906 Annex A
S2.35.A80.1270.4.
S2.35.A80.1610.4.
S2.35.A80.1270.4.
S2.35.A80.1610.4.
0 400 800 1200 1600 2000 2400 2800 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S2.35.A80.1270.4.
S2.35.A80.1610.4.
TM04
659
6 06
10
0 400 800 1200 1600 2000 2400 2800 Q [US GPM]
0
40
80
120
160
200
240
280
[ft]H
0 50 100 150 200 Q [l/s]
0
20
40
60
80
[m]H
0
10
20
30
40
[ft]NPSH
70H.C/D/H
60 Hz
ISO 9906 Annex A
S2.35.A80.1270.4.
S2.35.A80.1610.4.
S2.35.A80.1270.4.
S2.35.A80.1610.4.
0 400 800 1200 1600 2000 2400 2800 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S2.35.A80.1270.4.
S2.35.A80.1610.4.
Performance curves Technical data
S pumps, range 70
Electrical data
Note: Enclosure class: IP68
Pump data
* With 50 ft (15 m) cable
Pump type P1 [kW]
P2 [hp]
No. of poles RPM Starting
method
IN Istart ηmotor [%] Cos φ Moment of inertia
[lbft2 (kgm2]
Breakdown torque Mmax [lbf*ft (Nm)][A] [A] 1/2 3/4 1/1 1/2 3/4 1/1
S2.35.A80.1270.4.70H 103 127 4 1778 Y/D 148 1105 94 94 92 0.80 0.86 0.88 20.2 (0.85) 1090 9 (1479)S2.35.A80.1610.4.70H 129 161 4 1777 Y/D 185 1380 94 94 93 0.77 0.85 0.88 26.1 (1.1) 1427 2 (1935)
Pump typeMax. solids size Max. installation depth Weight *
[inch (mm)] [feet (m)] [lbs (kg)]S2.35.A80.1270.4.70H.S. 3.5 (90) 66 (20) 2315 (1050)S2.35.A80.1270.4.70H.C 3.5 (90) 66 (20) 2557 (1160)S2.35.A80.1270.4.70H.D 3.5 (90) 66 (20) 2778 (1260)S2.35.A80.1270.4.70H.H 3.5 (90) 66 (20) 2778 (1260)S2.35.A80.1610.4.70H.S 3.5 (90) 66 (20) 2315 (1050)S2.35.A80.1610.4.70H.C 3.5 (90) 66 (20) 2557 (1160)S2.35.A80.1610.4.70H.D 3.5 (90) 66 (20) 2778 (1260)S2.35.A80.1610.4.70H.H 3.5 (90) 66 (20) 2778 (1260)
37
Performance curves Technical data
S pumps, range 70
38
S 70 high pressure, 6- and 8-pole
S2.45.A100.1070, S2.45.A100.1470 and S2.45.A100.1880
TM04
659
7 06
10TM
04 6
598
0610
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 Q [US GPM]
0
20
40
60
80
100
120
140
160
[ft]H
0 50 100 150 200 250 300 350 400 450 Q [l/s]
0
10
20
30
40
50
[m]H
0
10
20
30
40
[ft]NPSH
70H.S
60 Hz
ISO 9906 Annex A
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 Q [US GPM]
0
20
40
60
80
100
120
140
160
[ft]H
0 50 100 150 200 250 300 350 400 450 Q [l/s]
0
10
20
30
40
50
[m]H
0
10
20
30
40
[ft]NPSH
70H.C/D/H
60 Hz
ISO 9906 Annex A
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 Q [US GPM]
0
50
100
150
200
[hp]
P2
0
50
100
150
[kW]
P2
S2.45.A100.1470.6.
S2.45.A100.1880.6.
S2.45.A100.1070.8.
Performance curves Technical data
S pumps, range 70
Electrical data
Note: Enclosure class: IP68
Pump data
* With 50 ft (15 m) cable
Pump type P1 [kW]
P2 [hp]
No. of poles RPM Starting
method
IN Istart ηmotor [%] Cos φ Moment of inertia
[lbft2 (kgm2]
Breakdown torque Mmax [lbf*ft (Nm)][A] [A] 1/2 3/4 1/1 1/2 3/4 1/1
S2.45.A100.1470.6.70H 118 147 6 1181 Y/D 175 1275 91 93 93 0.73 0.81 0.85 49.8 (2.1) 1639.6 (2223)S2.45.A100.1880.6.70H 152 188 6 1186 Y/D 242 1978 92 92 92 0.63 0.73 0.79 66.4 (2.8) 2162.1 (2930)S2.45.A100.1070.8.70H 86 107 8 882 Y/D 129 861 93 94 93 0.77 0.83 0.84 49.8 (2.1) 1600.5 (2170)
Pump typeMax. solids size Max. installation depth Weight *
[inch (mm)] [feet (m)] [lbs (kg)]S2.45.A100.1470.6.70H.S 4.5 (115) 66 (20) 2535 (1150)S2.45.A100.1470.6.70H.C 4.5 (115) 66 (20) 2800 (1270)S2.45.A100.1470.6.70H.D 4.5 (115) 66 (20) 3042 (1380)S2.45.A100.1470.6.70H.H 4.5 (115) 66 (20) 3042 (1380)S2.45.A100.1880.6.70H.S 4.5 (115) 66 (20) 2800 (1270)S2.45.A100.1880.6.70H.C 4.5 (115) 66 (20) 3086 (1400)S2.45.A100.1880.6.70H.D 4.5 (115) 66 (20) 3351 (1520)S2.45.A100.1880.6.70H.H 4.5 (115) 66 (20) 3351 (1520)S2.45.A100.1070.8.70H.S 4.5 (115) 66 (20) 2535 (1150)S2.45.A100.1070.8.70H.C 4.5 (115) 66 (20) 2800 (1270)S2.45.A100.1070.8.70H.D 4.5 (115) 66 (20) 3042 (1380)S2.45.A100.1070.8.70H.H 4.5 (115) 66 (20) 3042 (1380)
39
40
S pumps, range 70Accessories
Accessories (for installation)
* Installation type S and C pumps with discharge flange size NPS 10" (DN 250) and higher are supplied with guide claw mounted on the flange.
Pump type Installation accessoriesS 50-70 S and C NPS 3-8 (DN 80-200) without guide claw (guide claw included in auto-coupling kit)S 50-70 S and C NPS 10-24 (DN 250-600) with guide claw mounted on the pumpS 50-70 D Pump without installation accessories (accessories as separate kit)S 50-70 H Base stand for horizontal, dry installation supplied together with the pump
Pictures Description Size Weight[kg] PN Product
number
GR
8126
Cast-iron, epoxy-coated auto-coupling system complete with:• guide claw *• base unit• upper guide rail bracket• gaskets and bolts.
Dis
char
ge fl
ange
NPS 8" (DN 200)
551(250 10 97506541
NPS 10"(DN 250)
491(223) 10 97510048
NPS 12" (DN 300)
595(270) 10 97510049
NPS 20"(DN 500)
1549 85(703) 10 97510050
Intermediate guide rail bracket For guide rails longer than 19.5 feet (6 m) DN 200-600 8 96255842
Guide rails Standard pipes. Not supplied by Grundfos
TM03
201
5 35
05
Base plate for vertical, dry installation.With gaskets and bolts. Steel, epoxy-coated.
Suc
tion
flang
e
NPS 10"(DN 250) - 96857815
NPS 12" (DN 300) - 96857816
TM04
369
3 49
08
Base plate for vertical, dry installation.With gaskets and bolts.Cast iron, epoxy-coated.
NPS 16"/NPS 20"(DN 400/DN 500) - 96867808
TM04
415
8 09
09
Base stand for horizontal, dry installation.
140 96308192
TM04
416
0 09
09
140 96308212
TM04
415
9 09
09
125 96308255
Accessories S pumps, range 70
Other accessories
Pictures Description Dimensions Product number
TM02
612
6 51
0213 ft (4 m) galvanised lifting chain with lifting link and safety hook.With certificates.
7054.8 lbs(3200 kg) S 62-72
96468294
20 ft (6 m) galvanised lifting chain with lifting link and safety hook.With certificates. 96468295
26 ft (8 m) galvanised lifting chain with lifting link and safety hook.With certificates. 96468296
33 ft (10 m) galvanised lifting chain with lifting link and safety hook. With certificates. 96468297
40 ft (12 m) galvanised lifting chain with lifting link and safety hook.With certificates. 96468298
13 ft (4 m) stainless steel lifting chain with lifting link and safety hook.With certificates.
7054.8 lbs(3200 kg) S 62-72
96490259
20 ft (6 m) stainless steel lifting chain with lifting link and safety hook. With certificates. 96490270
26 ft (8 m) stainless steel lifting chain with lifting link and safety hook. With certificates. 96490271
33 ft (10 m) stainless steel lifting chain with lifting link and safety hook.With certificates. 96490272
40 ft (12 m) stainless steel lifting chain with lifting link and safety hook. With certificates. 96490273
TM01
698
2 39
99
Float switch with 33 ft (10 m) cable 96003332
Float switch with 66 ft (20 m) cable 96003695
TM02
886
2 09
04
Bracket for two float switches 96003338
TM02
067
0 50
00
Float switches with bracket, 33 ft (10 m) cable
2 switches, 1 pump without alarm 62500013
3 switches, 1 pump with alarm 62500014
3 switches, 2 pumps with alarm 62500014
4 switches, 2 pumps with alarm 62500015
41
42
S pumps, range 70Dimensions
Installation on auto coupling
Fig.
14
Dim
ensi
onal
ske
tche
s, in
stal
latio
n on
aut
o-co
uplin
g sy
stem
Z12a
is m
inim
um re
com
men
ded
dist
ance
from
pit
botto
m to
bot
tom
of p
ump
suct
ion
side
.
Z11
is to
tal h
eigh
t of p
ump
inst
alle
d on
Gru
ndfo
s in
stal
latio
n ac
cess
ory
in th
e pi
t. N
OTE
: Thi
s fig
ure
mig
ht n
ot e
qual
Z12
a +
Z1.
Not
e:
TM04 2418 2508
Z14
Min
. lev
el,
inst
alla
tion
S
Min
. lev
el,
inst
alla
tion
C
Dimensions S pumps, range 70
S pu
mps
, ran
ge 7
0 [in
ch]
ZM
4 X
M24
4 X
M24
4 X
M24
4 X
M24
4 X
M24
4 X
M24
4 X
M24
4 X
M24
6 X
M30
4 X
M24
6 X
M30
4 X
M24
ZDt1
1.2
1.2
1.3
1.3
1.2
1.2
1.3
1.3
1.7
1.3
1.7
1.3
DN
1
8" 8"
10"
12"
8" 8" 10"
10"
20"
12"
20"
12"
ZDc1
11.6
11.6
13.8
15.7
11.6
11.6
13.8
13.8
24.4
15.7
24.4
15.7
Z16
19.1
19.1
21.5
25.6
19.1
19.1
21.5
21.5
35.0
25.6
35.0
25.6
Z15
14.4
14.4
14.8
17.7
14.4
14.4
14.8
14.8
22.2
17.7
22.2
17.7
Z14
3.4
3.4
3.4
3.7
3.4
3.4
3.4
3.4
3.9
3.7
3.9
3.7
Z13
5.9
5.9
7.9
15.7
5.9
5.9
7.9
7.9
7.9
15.7
7.9
15.7
Z12b
7.7
7.7
8.8
10.1
7.7
7.7
8.8
8.8
15.0
10.1
15.0
10.1
Z12a
5.6
5.2
7.4
8.1
5.6
5.2
7.4
7.4
7.9
8.1
7.9
8.1
Z11
69.6
69.6
73.9
83.5
69.6
69.6
80.0
73.9
86.0
89.6
79.9
83.5
Z10 3.
53.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
Z9 6.7
6.7
6.7
6.7
6.7
6.7
6.7
6.7
6.7
6.7
6.7
6.7
Z8 35.1
33.5
45.0
43.0
43.0
33.5
45.0
45.0
65.1
43.0
65.1
43.0
Z7 45.7
47.3
62.4
60.3
53.6
47.3
62.4
62.4
90.4
60.3
90.4
60.3
Z6 60.3
61.8
78.4
80.3
68.1
61.8
78.4
78.4
119.
280
.311
9.2
80.3
Z5 - - - - - - - - 5.9 - 5.9 -
Z4 21.1
21.1
22.2
26.4
21.1
21.1
22.2
22.2
34.8
26.4
34.8
26.4
Z3 7.9
7.9
7.9
7.9
7.9
7.9
7.9
7.9
7.9
7.9
7.9
7.9
Z2 16.9
16.9
18.5
21.7
16.9
16.9
18.5
18.5
25.9
21.7
25.9
21.7
Z1 64.0
64.5
66.5
75.4
64.0
64.5
72.6
66.5
78.1
81.5
72.0
75.4
Z?1
8 X
23
8 X
23
12 X
23
12 X
23
8 X
23
8 X
23
12 X
23
12 X
23
20 X
27
12 X
23
20 X
27
12 X
23
F
22.4
28.3
35.1
35.7
22.4
28.3
35.1
35.1
50.0
35.7
50.0
35.7
C 30.3
31.9
47.0
44.8
38.2
31.9
47.0
47.0
72.6
44.8
72.6
44.8
Pum
p ty
pe
S2.
35.A
80.1
270.
4.70
HS
2.40
.A80
.127
0.4.
70M
S2.
45.A
100.
1470
.6.7
0HS
2.55
.A12
0.14
70.6
.70M
S2.
35.A
80.1
610.
4.70
HS
2.40
.A80
.161
0.4.
70M
S2.
45.A
100.
1880
.6.7
0HS
2.45
.A10
0.10
70.8
.70H
S3.
45.A
200.
1880
.6.7
0LS
3.45
.A12
0.18
80.6
.70M
S3.
45.A
200.
1070
.8.7
0LS
3.45
.A12
0.10
70.8
.70M
S pu
mps
, ran
ge 7
0 [m
m]
ZM4
X M
244
X M
244
X M
244
X M
244
X M
244
X M
244
X M
244
X M
246
X M
304
X M
246
X M
304
X M
24
ZDt1
31 31 32 32 31 31 32 32 42 32 42 32
DN
18" 8" 10
"12
"8" 8" 10
"10
"20
"12
"20
"12
"
ZDc1
295
295
350
400
295
295
350
350
620
400
620
400
Z16
485
485
545
650
485
485
545
545
890
650
890
650
Z15
365
365
375
450
365
365
375
375
565
450
565
450
Z14
86 86 86 95 86 86 86 86 98 95 98 95
Z13
150
150
200
400
150
150
200
200
200
400
200
400
Z12b
196
196
224
256
196
196
224
224
380
256
380
256
Z12a
143
131
189
206
143
131
189
189
200
206
200
206
Z11
1768
1769
1878
2121
1768
1769
2033
1878
2185
2276
2030
2121
Z10
88 88 88 88 88 88 88 88 88 88 88 88
Z9 170
170
170
170
170
170
170
170
170
170
170
170
Z8 892
852
1142
1092
1092
852
1142
1142
1654
1092
1654
1092
Z7 1162
1201
1585
1531
1362
1201
1585
1585
2297
1531
2297
1531
Z6 1531
1570
1992
2040
1731
1570
1992
1992
3028
2040
3028
2040
Z5 - - - - - - - -15
0 -15
0 -
Z4 535
535
565
670
535
535
565
565
885
670
885
670
Z3 200
200
200
200
200
200
200
200
200
200
200
200
Z2 430
430
471
551
430
430
471
471
657
551
657
551
Z1 1625
1638
1689
1915
1625
1638
1844
1689
1985
2070
1830
1915
Z?1
8 X
23
8 X
23
12 X
23
12 X
23
8 X
23
8 X
23
12 X
23
12 X
23
20 X
27
12 X
23
20 X
27
12 X
23
F 570
720
891
907
570
720
891
891
1269
907
1269
907
C 770
809
1193
1139
970
809
1193
1193
1843
1139
1843
1139
Pum
p ty
peS
2.35
.A80
.127
0.4.
70H
S2.
40.A
80.1
270.
4.70
MS
2.45
.A10
0.14
70.6
.70H
S2.
55.A
120.
1470
.6.7
0MS
2.35
.A80
.161
0.4.
70H
S2.
40.A
80.1
610.
4.70
MS
2.45
.A10
0.18
80.6
.70H
S2.
45.A
100.
1070
.8.7
0HS
3.45
.A20
0.18
80.6
.70L
S3.
45.A
120.
1880
.6.7
0MS
3.45
.A20
0.10
70.8
.70L
S3.
45.A
120.
1070
.8.7
0M
43
Dimensions S pumps, range 70
44
Dry pit, vertical installation
Fig.
15
Dim
ensi
onal
ske
tch,
dry
, ver
tical
inst
alla
tion
TM04 2423 2508/TM04 2424 2508
X3
XDc2
X16
X16
XDc2
Dimensions S pumps, range 70
S pu
mps
, ran
ge 7
0 [in
ch]
XM1
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
-M
24X
6-
M24
X6
XDC
3
14.3
14.3
17.0
17.0
14.3
14.3
17.0
17.0
0.0
17.0
0.0
17.0
XDC
2
11.7
11.7
14.3
17.0
11.7
11.7
14.3
14.3
25.0
17.0
25.0
17.0
DT2 1.0
1.0
1.2
1.3
1.0
1.0
1.2
1.2
1.5
1.3
1.5
1.3
D2N 8 8 12 12 8 8 12 12 20 12 20 12
D1N 12 12 6 6 12 12 6 6 8 6 8 6
X04
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X03
0.9
0.9
1.0
1.0
0.9
0.9
1.0
1.0
0.0
1.0
0.0
1.0
X02
0.9
0.9
0.9
1.0
0.9
0.9
0.9
0.9
1.3
1.0
1.3
1.0
X16
98.2
98.2
105.
010
5.0
98.2
98.2
111.
110
5.0
82.9
111.
176
.810
3.4
X12
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X11
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X10
10"
10"
12"
12"
10"
10"
12"
12"
16"
12"
16"
12"
X9 0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X8 0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X7 0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X6 33.7
33.7
34.8
34.8
33.7
33.7
34.8
34.8
0.0
34.8
0.0
34.8
X5 16.7
16.7
15.8
15.8
16.7
16.7
15.8
15.8
0.0
15.8
0.0
15.8
X4 15.7
15.7
17.7
17.7
15.7
15.7
17.7
17.7
0.0
17.7
0.0
17.7
X3 0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
X2 8.9
8.5
11.4
10.9
8.9
8.5
11.4
11.4
18.1
10.9
18.1
10.9
X1 64.5
64.5
70.2
70.2
64.5
64.5
76.3
70.2
82.9
76.3
76.8
68.6
E
19.7
18.1
29.5
27.6
19.7
18.1
29.5
29.5
47.2
27.6
47.2
27.6
C 30.3
31.9
47.0
44.8
30.3
31.9
47.0
47.0
72.6
44.8
72.6
44.8
Pum
p ty
pe
S2.
35.A
80.1
270.
4.70
HS
2.40
.A80
.127
0.4.
70M
S2.
45.A
100.
1470
.6.7
0HS
2.55
.A12
0.14
70.6
.70M
S2.
35.A
80.1
610.
4.70
HS
2.40
.A80
.161
0.4.
70M
S2.
45.A
100.
1880
.6.7
0HS
2.45
.A10
0.10
70.8
.70H
S3.
45.A
200.
1880
.6.7
0LS
3.45
.A12
0.18
80.6
.70M
S3.
45.A
200.
1070
.8.7
0LS
3.45
.A12
0.10
70.8
.70M
S pu
mps
, ran
ge 7
0 [m
m]
XM1
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
M24
X6
-M
24X
6-
M24
X6
XDC
3
362
362
432
432
362
362
432
432 0 432 0 432
XDC
2
298
296
362
432
298
296
362
362
635
432
635
432
DT2 26 26 30 33 26 26 30 30 37 33 37 33
D2N 8 8 12 12 8 8 12 12 20 12 20 12
D1N 12 12 6 6 12 12 6 6 8 6 8 6
X04 0 0 0 0 0 0 0 0 0 0 0 0
X03
24 24 25 25 24 24 25 25 0 25 0 25
X02
24 24 24 25 24 24 24 24 32 25 32 25
X16
2495
2495
2666
2666
2495
2495
2821
2 666
2106
2821
1951
2626
X12 0 0 0 0 0 0 0 0 0 0 0 0
X11 0 0 0 0 0 0 0 0 0 0 0 0
X10
10"
10"
12"
12"
10"
10"
12"
12"
16"
12"
16"
12"
X9 0 0 0 0 0 0 0 0 0 0 0 0
X8 0 0 0 0 0 0 0 0 0 0 0 0
X7 0 0 0 0 0 0 0 0 0 0 0 0
X6 857
857
883
883
857
857
883
883 0 883 0 883
X5 425
425
401
401
425
425
401
401 0 401 0 401
X4 400
400
450
450
400
400
450
450 0 450 0 450
X3 0 0 0 0 0 0 0 0 0 0 0 0
X2 226
215
289
278
226
215
289
289
461
278
461
278
X1 1638
1638
1783
1783
1638
1638
1938
1783
2106
1938
1951
1743
E 500
460
750
700
500
460
750
750
1200
700
1200
700
C 770
809
1193
1139
770
809
1193
1193
1843
1139
1843
1139
Pum
p ty
pe
S2.
35.A
80.1
270.
4.70
HS
2.40
.A80
.127
0.4.
70M
S2.
45.A
100.
1470
.6.7
0HS
2.55
.A12
0.14
70.6
.70M
S2.
35.A
80.1
610.
4.70
HS
2.40
.A80
.161
0.4.
70M
S2.
45.A
100.
1880
.6.7
0HS
2.45
.A10
0.10
70.8
.70H
S3.
45.A
200.
1880
.6.7
0LS
3.45
.A12
0.18
80.6
.70M
S3.
45.A
200.
1070
.8.7
0LS
3.45
.A12
0.10
70.8
.70M
45
Dimensions S pumps, range 70
46
Dry pit, horisontal installation
Fig.
16
Dim
ensi
onal
ske
tch,
dry
, hor
ison
tal i
nsta
llatio
n
TM04 2415 2508
D1NQZ4QZ2
QZ3
D2N
Dimensions S pumps, range 70
S pu
mps
, ran
ge 7
0 [in
ch]
QZ4 4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
QZ3
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
QZ2
13.3
13.3
19.0
19.0
13.3
13.3
19.0
19.0
25.6
19.0
25.6
17.4
D02 0.9
0.9
0.9
1.0
0.9
0.9
0.9
0.9
1.3
1.0
1.3
1.0
D2N 8 8 12 12 8 8 12 12 20 12 20 12
DN
2
8" 8" 10"
12"
8" 8" 10"
10"
20"
12"
20"
12"
DC
02
11.7
11.7
14.3
17.0
11.7
11.7
14.3
14.3
25.0
17.0
25.0
17.0
DT2 1.0
1.0
1.2
1.3
1.0
1.0
1.2
1.2
1.5
1.3
1.5
1.3
D1N 12 12 6 6 12 12 6 6 8 6 8 6
QD
N1
10"
10"
12"
12"
10"
10"
12"
12"
16"
12"
16"
12"
QD
C1
14.3
14.3
17.0
17.0
14.3
14.3
17.0
17.0
21.3
17.0
21.3
17.0
Q03 1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
Q01
M20
M20
M20
M20
M20
M20
M20
M20
M24
M20
M24
M20
Q10
53.4
53.4
53.4
53.4
53.4
53.4
53.4
53.4
53.4
53.4
53.4
53.4
Q9
11.3
11.3
17.0
17.0
11.3
11.3
17.0
17.0
23.7
17.0
23.7
15.5
Q8
27.6
27.6
27.6
27.6
27.6
27.6
27.6
27.6
27.6
27.6
27.6
27.6
Q7
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
Q6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
Q5
15.6
15.6
21.3
21.3
15.6
15.6
21.3
21.3
27.9
21.3
27.9
19.7
Q4
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
Q3
51.2
49.6
61.0
59.1
51.2
49.6
61.0
61.0
78.7
59.1
78.7
59.1
Q2
8.9
8.5
11.4
10.9
8.9
8.5
11.4
11.4
18.1
10.9
18.1
10.9
Q1
64.5
64.5
70.2
70.2
64.5
64.5
76.3
70.2
82.9
76.3
76.8
68.6
F
22.4
28.3
35.1
35.7
22.4
28.3
35.1
35.1
50.0
35.7
50.0
35.7
D 10.2
15.7
18.8
20.6
11.2
15.7
18.8
18.8
28.3
20.6
28.3
20.6
Des
crip
tion
S2.
35.A
80.1
270.
4.70
HS
2.40
.A80
.127
0.4.
70M
S2.
45.A
100.
1470
.6.7
0HS
2.55
.A12
0.14
70.6
.70M
S2.
35.A
80.1
610.
4.70
HS
2.40
.A80
.161
0.4.
70M
S2.
45.A
100.
1880
.6.7
0HS
2.45
.A10
0.10
70.8
.70H
S3.
45.A
200.
1880
.6.7
0LS
3.45
.A12
0.18
80.6
.70M
S3.
45.A
200.
1070
.8.7
0LS
3.45
.A12
0.10
70.8
.70M
S pu
mps
, ran
ge 7
0 [m
m]
QZ4
107
107
107
107
107
107
107
107
107
107
107
107
QZ3 -50
-50
-50
-50
-50
-50
-50
-50
-50
-50
-50
-50
QZ2 338
338
483
483
338
338
483
483
651
483
651
443
D02 24 24 24 25 24 24 24 24 32 25 32 25
D2N 8 8 12 12 8 8 12 12 20 12 20 12
DN
2
8" 8" 10"
12"
8" 8" 10"
10"
20"
12"
20"
12"
DC
02
298
296
362
432
298
296
362
362
635
432
635
432
DT2 26 26 30 33 26 26 30 30 37 33 37 33
D1N 12 12 6 6 12 12 6 6 8 6 8 6
QD
N1
10"
10"
12"
12"
10"
10"
12"
12"
16"
12"
16"
12"
QD
C1
362
362
432
432
362
362
432
432
540
432
540
432
Q03 28 28 28 28 28 28 28 28 28 28 28 28
Q01
M20
M20
M20
M20
M20
M20
M20
M20
M24
M20
M24
M20
Q10
1357
1357
1357
1357
1357
1357
1357
1357
1357
1357
1357
1357
Q9
288
288
433
433
288
288
433
433
601
433
601
393
Q8
700
700
700
700
700
700
700
700
700
700
700
700
Q7
600
600
600
600
600
600
600
600
600
600
600
600
Q6
600
600
600
600
600
600
600
600
600
600
600
600
Q5
395
395
540
540
395
395
540
540
708
540
708
500
Q4
800
800
800
800
800
800
800
800
800
800
800
800
Q3
1300
1260
1550
1500
1300
1260
1550
1550
2000
1500
2000
1500
Q2
226
215
289
278
226
215
289
289
461
278
461
278
Q1
1638
1638
1783
1783
1638
1638
1938
1783
2106
1938
1951
1743
F 570
720
891
907
570
720
891
891
1269
907
1269
907
D 258
400
478
522
285
400
478
478
719
522
719
522
Pum
p ty
pe
S2.
35.A
80.1
270.
4.70
HS
2.40
.A80
.127
0.4.
70M
S2.
45.A
100.
1470
.6.7
0HS
2.55
.A12
0.14
70.6
.70M
S2.
35.A
80.1
610.
4.70
HS
2.40
.A80
.161
0.4.
70M
S2.
45.A
100.
1880
.6.7
0HS
2.45
.A10
0.10
70.8
.70H
S3.
45.A
200.
1880
.6.7
0LS
3.45
.A12
0.18
80.6
.70M
S3.
45.A
200.
1070
.8.7
0LS
3.45
.A12
0.10
70.8
.70M
47
48
S pumps, range 70Further product documentation
WebCAPSWebCAPS is a Web-based Computer Aided Product Selection program available on www.grundfos.com.
WebCAPS contains detailed information on more than 185,000 Grundfos products in more than 20 languages.
In WebCAPS, all information is divided into 6 sections:
• Catalogue• Literature• Service• Sizing• Replacement• CAD drawings.
Catalogue
This section is based on fields of application and pump types, and contains • technical data• curves (QH, Eta, P1, P2, etc) which can be adapted to the den-
sity and viscosity of the pumped liquid and show the number of pumps in operation
• product photos• dimensional drawings• wiring diagrams• quotation texts, etc.
Literature
In this section you can access all the latest documents of a given pump, such as• data booklets• installation and operating instructions• service documentation, such as Service kit catalogue and
Service kit instructions• quick guides• product brochures, etc.
Service
This section contains an easy-to-use interactive service cata-logue. Here you can find and identify service parts of both existing and discontinued Grundfos pumps.Furthermore, this section contains service videos showing you how to replace service parts.
Further product documentation
S pumps, range 70
WinCAPS
Fig. 17 WinCAPS CD-ROM
WinCAPS is a Windows-based Computer Aided Prod-uct Selection program containing detailed information on more than 185,000 Grundfos products in more than 20 languages.
The program contains the same features and functions as WebCAPS, but is an ideal solution if no Internet con-nection is available.
WinCAPS is available on CD-ROM and updated once a year.
Sizing
This section is based on different fields of application and installa-tion examples, and gives easy step-by-step instructions in how to• select the most suitable and efficient pump for your installation• carry out advanced calculations based on energy consumption,
payback periods, load profiles, life cycle costs, etc.• analyse your selected pump via the built-in life cycle cost tool• determine the flow velocity in wastewater applications, etc.
Replacement
In this section you find a guide to selecting and comparing re-placement data of an installed pump in order to replace the pump with a more efficient Grundfos pump. The section contains replacement data of a wide range of pumps produced by other manufacturers than Grundfos.
Based on an easy step-by-step guide, you can compare Grund-fos pumps with the one you have installed on your site. When you have specified the installed pump, the guide will suggest a number of Grundfos pumps which can improve both comfort and efficiency.
CAD drawings
In this section it is possible to download 2-dimensional (2D) and 3-dimensional (3D) CAD drawings of most Grundfos pumps.
These formats are available in WebCAPS:
2-dimensional drawings:• .dxf, wireframe drawings• .dwg, wireframe drawings.
3-dimensional drawings:• .dwg, wireframe drawings (without surfaces)• .stp, solid drawings (with surfaces)• .eprt, E-drawings.
0 1
Subject to alterations.
49