S /SDL LED INSTALLATION AND ASSEMBLY INSTRUCTIONS IMPORTANT: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD VOID ALL WARRANTIES! WARNING! RISK OF FIRE OR ELECTRICAL SHOCK OR PRODUCT DAMAGE Disconnect power before installing or servicing. Do not electrically connect live wiring! WARNING: Risk of fire or electric shock. Do not alter, relocate, or remove wiring, power supply or any other electrical component. WARNING: Risk of fire or electric shock. Installation of this luminaire requires a person familiar with the construction and operation of the luminaire's electrical system and the hazards involved. If not qualified do not attempt installation. Contact a qualified electrician. -Verify that supply wiring voltage matches power supply voltage by comparing it with power supply label. -Make all electrical and and grounded connections in accordance with the National Electric Code (NEC) and any other applicable local code requirements. CAUTION: RISK OF INJURY. - Wear gloves and safety glasses at all times when removing luminaire from carton, installing , servicing or performing maintenance. -Never connect components under load. -Do NOT mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. -Do NOT restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection of conduction cooling. -Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.
Transcript
S /SDL LED INSTALLATION AND ASSEMBLY INSTRUCTIONS
IMPORTANT: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD VOID ALL WARRANTIES!
WARNING! RISK OF FIRE OR ELECTRICAL SHOCK OR PRODUCT DAMAGE
Disconnect power before installing or servicing. Do not electrically connect live wiring!
WARNING: Risk of fire or electric shock. Do not alter, relocate, or remove wiring, power supply or any other
electrical component.
WARNING: Risk of fire or electric shock. Installation of this luminaire requires a person familiar with the
construction and operation of the luminaire's electrical system and the hazards involved. If not qualified do not
attempt installation. Contact a qualified electrician.
-Verify that supply wiring voltage matches power supply voltage by comparing it with power supply label.
-Make all electrical and and grounded connections in accordance with the National Electric Code (NEC) and
any other applicable local code requirements.
CAUTION: RISK OF INJURY.
- Wear gloves and safety glasses at all times when removing luminaire from carton, installing , servicing or
performing maintenance.
-Never connect components under load.
-Do NOT mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
-Do NOT restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED
fixtures with insulation, foam, or other material that will prevent convection of conduction cooling.
-Always read the fixtures complete installation instructions prior to installation for any additional fixture
specific warnings.
AutoCAD SHX Text
PAGE (1
S/SDL LED INSTALLATION AND ASSEMBLY INSTRUCTIONS
AutoCAD SHX Text
1.) UNPACK STRIP.
AutoCAD SHX Text
8). ROW MOUNTING OPTION: HOUSING END CAN BE ROTATED 90 DEGREES TO BE USED AS JOINER AS SHOWN BELOW.
AutoCAD SHX Text
PAGE (2
AutoCAD SHX Text
PACKAGE INCLUDES SCREWS. X4 FOR 2 & 4FT UNITS. X8 FOR 8FT UNITS
AutoCAD SHX Text
2.) TO INSTALL FIXTURE COVER NEEDS TO BE REMOVED BY COMPRESSING HOUSING SIDES TO FREE TABS ON HOUSING FROM SLOTS ON COVER. (REMOVAL OF LENS NOT REQUIRED FOR INSTALL.)
AutoCAD SHX Text
3.) SURFACE MOUNT SURFACE MOUNT SCREWS (BY OTHERS) USED TO ATTACH FIXTURE.
AutoCAD SHX Text
4.) PENDANT MOUNT PENDANT MOUNT USE 7/8 (.875") KNOCK OUTS IN HOUSING.
AutoCAD SHX Text
5.) GRID HANGER MOUNTING. GRID HANGER MOUNTING. SECURE LSI GRID HANGERS TO T-GRID. CAPTURE HOUSING USING GRID HANGERS.
AutoCAD SHX Text
6.) CHAIN MOUNTING.CHAIN MOUNTING.
AutoCAD SHX Text
7). T-GRID COLLAR OPTION: ATTACHED J-BOX TO T-GRID AND FASTEN WIRE COLLAR TO J-BOX TO SECURE TO GRID SYSTEM. HOLD FIXTURE UP TO COLLAR AND BEND TABS TO HOLD IN PLACE. MAKE WIRE CONNECTIONS.
AutoCAD SHX Text
*LENS REMOVAL NOT REQUIRED FOR INSTALL. LENS REMOVAL INSTRUCTIONS FOR TROUBLESHOOTING PURPOSES PAGE 4*
FROM
BUILDING
SUPPLY
TO
FIXTURE
HOT
GROUND
NEUTRAL
BLACK
WHITE
GREEN
WIRENUT
(SPLICES MADE
IN FIELD)
S/SDL LED INSTALLATION AND ASSEMBLY INSTRUCTIONSMOUNTING ACCESSORIES
S/SDL GRID HANGER BRACKET LSI# 648480
S/SDL GRID MTG FEED COLLAR LSI# 555914
S/SDL CHAIN MTG KIT.LSI# M38258 36"& 251057 60".
S/SDL WIRE GUARD
S/SDL LED INSTALLATION AND ASSEMBLY INSTRUCTIONS
AutoCAD SHX Text
NOTE: SEE DRIVER FOR CURRENT AND VOLTAGE.
AutoCAD SHX Text
PAGE (3
AutoCAD SHX Text
10.) REPLACE COVER AND REATTACH BY ALIGNING HOUSING TABS WITH SLOTS ON COVER. FIXTURE IS INSTALLED AND CAN BE ENERGIZED.
AutoCAD SHX Text
9.) TYP WIRING.TYP WIRING.
AutoCAD SHX Text
11.) DISENGAGE LED PANEL FROM HOUSING. ATTACH CLIPS TO PANEL. SECURE WIRE GUARD TO CLIPS. REATTACH LED PANEL TO HOUSING.
AutoCAD SHX Text
OPTIONAL:SECURE COVER TO HOUSING WITH SCREWS PACKAGED WITH FIXTURE. :SECURE COVER TO HOUSING WITH SCREWS PACKAGED WITH FIXTURE.
AutoCAD SHX Text
PAGE (4
AutoCAD SHX Text
SDL HOUSING MOUNTING DETAILS:
AutoCAD SHX Text
BOTTOM VIEW
AutoCAD SHX Text
SIDE VIEW
AutoCAD SHX Text
SDL PEDANT & CANOPY DETAIL
AutoCAD SHX Text
PAGE (5
AutoCAD SHX Text
SDL LENS REMOVAL: LENS REMOVAL NOT REQUIRED FOR INSTALL! IF LENS REMOVAL IS REQUIRED FOR TROUBLESHOOTING PURPOSE SQUEEZE LENS ON SIDES TO UNCLIP FROM COVER.
