SANDPIPERPUMP.COM Warren Rupp, Inc. • A Unit of IDEX Corporation 800 N. Main St., Mansfield, Ohio 44902 USA Telephone 419.524.8388 • Fax 419.522.7867 5 YEAR LIMITED PRODUCT WARRANTY 5 Year Guarantee for defects in material or workmanship. See sandpiperpump.com/content/warranty-certifications for complete warranty, including terms and conditions, limitations and exclusions. F E A T U R E E X C L U S I V E USE ONLY GENUINE SANDPIPER PARTS All certification, standards, guarantees & warranties originally supplied with this pump will be invalidated by the use of service parts not identified as “Genuine SANDPIPER Parts.” SUCTION / DISCHARGE PORT SIZE • 3” NPT or 3” BSP Tapered • 3” ANSI Flange or 3” DIN Flange CAPACITY • 0 to 285 gallons per minute (0 to 1,078 LPM) AIR DISTRIBUTION VALVE • No-lube, no-stall design SOLIDS-HANDLING • Up to .38 in. (9.65mm) S30 METALLIC PUMP TECHNICAL DATA SHEET PERFORMANCE ISO 9001 Certified ISO 14001 Certified STANDARD DUTY BALL VALVE PUMPS Offering the widest range of performance and application capabilities SERIES Performance based on water at ambient temperature. CAPACITY GPM LPM 100 200 300 600 700 800 900 0 BAR PSI HEAD AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI PREVIOUS AIR PRESSURE IN PSI 1 2 3 4 5 6 7 8 9 0 20 (34) 40 (68) 60 (102) 80 (136) 100 (170) 120 (204) 140 (238) 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 1,000 1,100 400 500 125 PSI (8 Bar) 80 PSI (5.44 Bar) 60 PSI (4.08 Bar) 40 PSI (2.72 Bar) 20 PSI (1.36 Bar) Air Inlet Pressure 100 PSI (6.8 Bar) HEADS UP TO • 125 psi or 289 ft. of water (8.6 Kg/cm2 or 86 meters) MAXIMUM OPERATING PRESSURE • 125 psi (8.6 bar) DISPLACEMENT/STROKE • 1.00 Gallon / 3.79 liter WEIGHTS • Aluminum 116 lbs. (53kg) • Cast Iron 215 lbs. (98kg) • Stainless Steel 194 lbs. (87kg)
Transcript
S A N D P I P E R P U M P . C O M
Warren Rupp, Inc. • A Unit of IDEX Corporation800 N. Main St., Mansfield, Ohio 44902 USA Telephone 419.524.8388 • Fax 419.522.7867
5 YEAR LIMITED PRODUCT WARRANTY 5 Year Guarantee for defects in material or workmanship. See sandpiperpump.com/content/warranty-certifications for complete warranty, including terms and conditions, limitations and exclusions.
F E AT U R E
EXCLUSIVE
USE ONLY GENUINE SANDPIPER PARTS All certification, standards, guarantees & warranties originally supplied with this pump will be invalidated by the use of service parts not identified as “Genuine SANDPIPER Parts.”
SUCTION / DISCHARGE PORT SIZE• 3” NPT or 3” BSP Tapered• 3” ANSI Flange or 3” DIN Flange
CAPACITY• 0 to 285 gallons per minute (0 to 1,078 LPM)
AIR DISTRIBUTION VALVE• No-lube, no-stall design
SOLIDS-HANDLING• Up to .38 in. (9.65mm)
S30 METALLIC PUMPTECHNICAL DATA SHEET
PERFORMANCE
ISO 9001 Certified ISO 14001 Certified
II 2G EEx m c T5II 2D c IP65 T100°C
STANDARD DUTY BALL VALVE PUMPSOffering the widest range of performance and application capabilities
SERIES
Performance based on water at ambient temperature.
CAPACITY
GPM
LPM100 200 300 600 700 800 9000
BA
R
PS
I
HE
AD
AIR CONSUMPTION IN SCFMAIR PRESSURE IN PSIPREVIOUS AIR PRESSURE IN PSI
CONDUCTIVEACETAL: Tough, impact resistant, ductile. Good abrasion resistance and low friction surface. Generally inert, with good chemical resistance except for strong acids and oxidizing agents.
190°F88°C
-20°F-29°C
EPDM: Shows very good water and chemical resistance. Has poor resistance to oils and solvents, but is fair in ketones and alcohols.
280°F138°C
-40°F-40°C
FKM(FLUOROCARBON): Shows good resistance to a wide range of oils and solvents; especially all aliphatic, aromatic and halogenated hydrocarbons, acids, animal and vegetable oils. Hot water or hot aqueous solutions (over 70°F(21°C)) will attack FKM.
350°F177°C
-40°F-40°C
HYTREL®: Good on acids, bases, amines and glycols at room temperatures only.
220°F104°C
-20°F-29°C
NEOPRENE: All purpose. Resistance to vegetable oils. Gener-ally not affected by moderate chemicals, fats, greases and many oils and solvents. Generally attacked by strong oxidizing acids, ketones, esters and nitro hydrocarbons and chlorinated aromatic hydrocarbons.
200°F93°C
-10°F-23°C
NITRILE: General purpose, oil-resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not be used with highly polar solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons.
190°F88°C
-10°F-23°C
NYLON: 6/6 High strength and toughness over a wide tem-perature range. Moderate to good resistance to fuels, oils and chemicals.
180°F82°C
32°F0°C
POLYPROPYLENE: A thermoplastic polymer. Moderate tensile and flex strength. Resists stong acids and alkali. Attacked by chlorine, fuming nitric acid and other strong oxidizing agents.
180°F82°C
32°F0°C
PVDF: (Polyvinylidene Fluoride) A durable fluoroplastic with excellent chemical resistance. Excellent for UV applications. High tensile strength and impact resistance.
250°F121°C
0°F-18°C
SANTOPRENE®: Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance.
275°F135°C
-40°F-40°C
UHMWPE: A thermoplastic that is highly resistant to a broad range of chemicals. Exhibits outstanding abrasion and impact resistance, along with environmental stress-cracking resistance.
180°F82°C
-35°F-37°C
URETHANE: Shows good resistance to abrasives. Has poor resistance to most solvents and oils.
150°F66°C
32°F0°C
VIRGINPTFE: (PFA/TFE) Chemically inert, virtually impervious. Very few chemicals are known to chemically react with PTFE; molten alkali metals, turbulent liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at elevated temperatures.
220°F104°C
-35°F-37°C
Maximum and Minimum Temperatures are the limits for which these materials can be operated. Temperatures coupled with pressure affect the longevity of diaphragm pump components. Maximum life should not be expected at the extreme limits of the temperature ranges.
Metals:ALLOYC: Equal to ASTM494 CW-12M-1 specification for nickel and nickel alloy.
STAINLESSSTEEL: Equal to or exceeding ASTM specification A743 CF-8M for corro-sion resistant iron chromium, iron chromium nickel and nickel based alloy castings for general applications. Commonly referred to as 316 Stainless Steel in the pump industry.
For specific applications, always consult the Chemical Resistance Chart.
NOTE: See service manual for ATEX details. SP_DS_TemplateDataSheet_0817
PUMP BRAND S SANDPIPER®
PUMP SIZE 30 3”
CHECK VALVE TYPE B Ball
DESIGN LEVEL 1 Design Level
WETTED MATERIAL A Aluminum I Cast Iron S Stainless Steel H Alloy C X Unpainted Aluminum
DIAPHRAGM/CHECK VALVE MATERIALS 1 Santoprene/Santoprene 2 PTFE-Santoprene/PTFE B Nitrile/Nitrile C FKM/PTFE E EPDM/EPDM I EPDM/Santoprene G PTFE-Neoprene/PTFE
M Santoprene/PTFE N Neoprene/Neoprene
CHECK VALVE SEAT A Aluminum B Nitrile C Carbon Steel E EPDM N Neoprene S Stainless Steel T PTFE V FKM W UHMW Polyethylene
NON-WETTED MATERIAL OPTIONS A Painted Aluminum I Cast Iron J Painted Aluminum w/PTFE Coated Hardware S Stainless Steel with Stainless Steel Hardware Y Painted Aluminum with Stainless Steel Hardware Z Cast Iron with Stainless Steel Hardware
PORTING OPTIONS A 150# Raised Face 3” ANSI Flange (Integral Manifold) D 80 DIN Flange (Integral Manifold) N NPT Threads B BSP (Tapered) Threads
