MAKE: STYLE:
45
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: MODERATE
EASY MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be worn at all times whileinstalling this product.
YEARS: 2014-PRESENT SUBARU MODEL: OUTBACK WAGON
3,500350
TRAILER WEIGHT:TONGUE WEIGHT:
12136 INSTALLATION INSTRUCTIONS
LBS.LBS.
WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.
90 MIN.MIN. PRO INSTALL TIME:
NOVICE INSTALL TIME:
IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
SCAN FORMORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com 5/25/2016
SOCKET
10mm19mm
SOCKET
EXTENSION
8"
RATCHET
TORQUEWRENCH 17/32"
DRILL BITPOWERDRILL
ROTARY TOOLAVIATIONSHEARS
FISHWIRE HARDWIRE
HEAT SHIELD TRIM
HOLE ENLARGEMENT
DRILLING REQUIRED
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts ListDESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT1/2-13 x 1 1/241
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP642
HEX FLANGE NUTHFN 121343
1/2" FISHWIRE1_2 FISHWIRE24
1
2
34
1. Lower the exhaust by removing the (3) rearmost rubber exhaust isolators from the frame mounted hangers. Note: Support the exhaust during installation to prevent damage. (See Rubber Isolator Removal Diagram.)
2. Remove the muffler heat shield and trim to clear the hitch mounting plate. (See Heat Shield Trim Diagram.)
TRIM ALONGBEND LINE
PASSENGER SIDEFRAME RAIL
DRILL HOLE(BOTH SIDES)
ENLARGEACCESS HOLE(BOTH SIDES)
EXISTING HOLE(BOTH SIDES)DRIVER SIDE
FRAME RAIL
MUFFLER
EXHAUST ISOLATOR
DESIGNED FOR USE WITHBALLMOUNT #45521
EURO MOUNT OPTION AVAILABLE#45571 (1 7/8" BALL) & 45572 (2" BALL)
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
HOLE ENLARGEMENTDIAGRAM
3. Remove the (2) rubber plugs in each frame rail. Enlarge the forward hole on each frame rail to allow the carriage bolt and spacer to be inserted into the frame rail. (See Hole Enlargement Diagram.)
4. Fishwire a carriage bolt and spacer into the rearmost hole in each frame rail as shown. (See Fishwire Technique.)
5. Raise the hitch into position. Center the hitch on the vehicle, remove fishwire, and loosely secure the hitch to the vehicle with hex flange nuts as shown.
6. Using the hitch as your template mark and drill the forward holes in the frame rail. Fishwire a carriage bolt and spacer into each drilled hole and secure the hitch with a hex flange nut as shown.
REMOVE 1.125 in
.300 in
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
8. Torque all 1/2" hardware to 110 ft-lbs.
9. Reinstall the heat shield, raise the exhaust and reinstall the rubber isolators.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited torepair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
3,500 350
29
45
SUBARU OUTBACK5/25/2016
12136
90
PAGE 1 of 2
Scanfor moreinformation
Parts ListDESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT1/2-13 x 1 1/241.250 x 1.00 x 3.00" SQ. HOLE SPACERCM-SP642HEX FLANGE NUTHFN 1213431/2" FISHWIRE1_2 FISHWIRE24
INSTALLED HITCH POSITION
1
2
3
4
DRIVER SIDEFRAME RAIL
PASSENGER SIDEFRAME RAIL
EXHAUST HANGER (BOTH SIDES)
MUFFLER
ENLARGE HOLE(BOTH SIDES)
TOOLS REQUIRED10 AND 19mm SOCKETS
8" EXTENSIONRATCHET
TORQUE WRENCHDRILL AND 17/32" BIT
ROTARY TOOL / CARBIDE BITTIN SNIPS / FILE
DRILL HOLE
DRILL HOLE
BUMPER COVER
-DRILLING REQUIRED-FISHWIRE HARDWARE-TRIM HEAT SHEILD-HOLE ENLARGEMENT
EXISTING HOLE(BOTH SIDES)
DESIGNED FOR USE WITHBALLMOUNT #45521
EURO MOUNTOPTION AVAILABLE#45571 (1 7/8" BALL)
& #45572 (2" BALL)
HOLE ENLARGEMENTDIAGRAM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of thisproduct voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequentialloss or damage.
SUBARU OUTBACK3/11/2015
12136PAGE 2 of 2
1. Lower the exhaust by removing the (3) rearmost rubber exhaust isolators from the frame mounted hangers. Note: Support the exhaust during installation to prevent damage. (See Rubber Isolator Removal Diagram.) 2. Remove the muffler heat shield and trim to clear the hitch mounting plate. (See Heat Shield Trim Diagram.) 3. Remove the (2) rubber plugs in each frame rail. Enlarge the forward hole on each frame rail to allow the carriage bolt and spacer to be inserted into the frame rail. (See Hole Enlargement Diagram.) 4. Fishwire a carriage bolt and spacer into the rearmost hole in each frame rail as shown. (See Fishwire Technique.) 5. Raise the hitch into position. Center the hitch on the vehicle and loosely secure the hitch to the vehicle with hex flange nuts as shown. 6. Using the hitch as your template mark and drill the forwardmost holes in the frame rail. 7. Fishwire a carriage bolt and spacer into each drilled hole and secure the hitch with a hex flange nut as shown. 8. Torque all 1/2" hardware to 110 ft-lbs. 9. Reinstall the heat shield, raise the exhaust and reinstall the rubber isolators.
HEAT SHIELD TRIM DIAGRAM
TRIM ALONG BEND LINE
1.125 inREMOVE
.250 in