JQA-2042 NITTO KOHKI CO.,LTD.Machine Tools Division
ISO 9001JQA-EM4057NITTO KOHKI CO.,LTD.
HeadquartersResearch Center
ISO 14001
Cat.No. Tk103m
NITTO KOHKI CO.,LTD.
Safety Precautions
Be sure to read and understand all safety precautions mentioned below and to follow the instructions given to operate eachNitto Kohki brand tool as stated in the operator’s manual. Keep operators manual close by when operating machines or toolsfor reference of safe operation and precautions.
Failure to observe the following warnings may cause a potentially hazardous situation, which if not corrected could resultin serious injury or death. To prevent the risk of fire, electric shock, and/or personal injury, proper safety guidelines shouldbe followed at all times.
Warning for ALL Machines and Tools
Notice for Air ToolsNotice for Electric Tools• Air pressure at the inlet of the tool must not exceed 0.59 MPa (6 kgf/cm2).
SAFETY GUIDE
• Always keep the work area free from clutter and potentially dangerous conditions such as hanging power cords, working debris, air hoses, and garbage to prevent accidents from occurring.
• Consider proper working environments for each tool carefully. Do not expose tools to extreme amounts of moisture or direct contact with water or rain. Keep area well lit at all times to prevent hidden dangers and never operate the equipment near flammable liquids or in gaseous or explosive atmospheres.
• Keep all tools and tool accessories away from children and all unauthorized personnel. Serious injury or possible death may result from machines being handled by children.
• Properly store machines and accessories while not in use. They should be kept in a dry, locked-up location out of reach of children or unauthorized personnel.
• Improper or negligent use of tools will cause increased maintenance costs, and the amount of time in which to complete the job. Always let the tool do the work at the rate of which it was designed. Best performance is always achieved by reading and understanding the proper operation of each machine or tool.
• Always wear safety glasses and protective hand and foot wear during or around operating tools. Wear a protective hair covering to contain long hair. Do not wear loose clothing and/or accessories as they may be caught in moving parts and inflict serious injury or possible death.
• Wear respiratory protection when working in an environment where dust particles are generated during operation.
• Do not over-reach or allow yourself to become unstable during tool operation and always maintain a correct posture.
• Use clamps or a vise to secure the work piece tightly and eliminate vibration. Never hold the work piece with your hands, keep both hands on the tool for increased productivity.
• Use the right tool or machine that can complete the job within its specifications. Do not attempt to adapt smaller machines or tools to complete a job designed for heavy-duty equipment. Do not use the tools for other than what they were designed for. There is a right tool for each job, be aware of tool limitations and never overload.
• Make sure to inspect all external screws, nuts, bolts and attached accessories are fastened tightly and secure prior to each use. All moving parts should be free from obstruction and allowed to operate smoothly. Any damaged or missing parts should be repaired or replaced by the sales agent or distributor from which the tool was originally purchased. Do not use machines or tools which cannot be activated or stopped with a power switch or lever.
• Do not use any machine with a damaged, frayed, cut, or deteriorated power cords or air hoses. Always replace at the first sign of damage.
• The power source must be limited to the individual tools specifications as stated on the nameplate or instruction manual.
• Make sure that all machine and power tools are properly grounded at all times (excludes double-insulated tools). Always use a GFCI (Ground-Fault-Circuit-
Interrupt) to protect the user and surrounding persons from electric shock.• Be aware of low voltage situations. Improperly gauged extension cords or
power cords used or shared with other electrical devices will cause all tools on the line to not run at optimal performance. This condition may result in damage to the machine and/or operator.
• Always remove all tools required to adjust, add, or remove parts from tools prior to use to prevent tool damage or user injury.
• Always avoid an unexpected start by having all power buttons or levers in the off position prior to attaching to a power or air supply. Never carry tools with your finger on the on/off switch or lever when the power or air supply is attached.
• Do not use the power or air supply lines to move, carry or support the tool during usage or transportation. Do not place the power or air line near a heat source, oil, water, or items with sharp edges.
• Never leave a machine or tool running unattended. Keep a firm grip on the designated areas of the machine or tool until it comes to a complete stop. Always turn the power switch or lever to the off position and disconnect from the power source when not in use.
• Do not disassemble or modify a tool to complete a job other than what it was designed for. This will void any warranty on the equipment and may cause serious personal injury or possible death.
• Maintenance is necessary for all machines and tools. Always maintain blades and cutters properly and replace when edges become damaged or are not sharp enough for safe operation. Follow the instruction manual for lubrication needs and adjustment points if applicable. Check the power and air supply lines periodically and change accordingly to safety regulations. If an extension line is adopted, always make sure that it meets or exceeds tool requirements for amperage or air supply before using and is rated for outdoor usage. Change supply lines whenever they are found to be defective or damaged. Keep the grip and handles dry and clean of grease or oil so that it will not disturb proper operation.
• Switch off and disconnect from power source before servicing equipment or changing accessories.
• Be alert and pay close attention to the work being performed at all times. Do not operate machines or tools when heavily fatigued. Users should be aware of all circumstances surrounding their application.
• Use only recommended parts and accessories as per individual machine or tool operator manuals. Use of improper accessories or attachments may result in serious injury or possible death.
• All repairs and services must be performed by authorized Nitto Kohki dealers or technicians.
• Do not deface or remove any label, warning indicator, or nameplate associated with each machine or tool.
1
Whether you just glance through this booklet or give it an intensive reading, we are sure you'll agree thatNITTO KOHKI's portable hydraulic and electric machines, couplers and pneumatic hand tools are amongthe finest precision engineered equipment to be found today.
PageManufacturing SteelFabricating
Welding Metal Casting &Forging
AUTOMOTIVE &SHIP BUILDING
Construction
3-4
Drilling holesin shapedsteel
Drillingholes in steel
Speedy, highprecisionhole drilling
Speedy, highprecisionhole drilling
Drilling holesin shapedsteel
Drillingholes in steel
Speedy, highprecisionhole drilling
Speedy, highprecisionhole drilling
Drilling holesin shapedsteel
Drillingholes in steel
Speedy, highprecisionhole drilling
Speedy, highprecisionhole drilling
5
CONTENTS
PORTABLE MAGNETIC BASE AUTOMATIC DRILLING MACHINE
ATRA ACEauto feed (WA-3500 / WA-5000)
BORING
11
On-sitepunchingholes onshaped steels
Punchingholes on shipframeworks
Punchingbolt holeson steelplates
Holepunching onsteel plates
PORTABLE DOUBLE-ACTING HYDRAULIC PUNCHER
SELFER ACEHS SERIES & HYDRAULIC PUMP
PUNCHING
12
On-sitepunchingholes onshaped steels
Punchingholes on shipframeworks
Punchingbolt holeson steelplates
Holepunching onsteel plates
PORTABLE SINGLE-ACTING HYDRAULIC PUNCHER
SELFERHA SERIES & HYDRAULIC PUMP
PUNCHING
13-14
On-sitesmall holepunching
Punchingholes onangles andchannels
Speedy, easyholepunching onsteel sheets
ELECTRICALLY OPERATED HYDRAULIC PUNCHER
HANDY SELFER ANDPUNCHES & DIES FOR SELFER
PUNCHING
15
Chamferingof colums
Chamferingof steel plates
Chamferingof largeworkpieces
PORTABLE CHAMFERING TOOLS
BEVELERHAND BEVELER
CHAMFERING
Chamferingof steel plate
15-16
Chamferingof steel plate
Chamferingof dies andmachine
PORTABLE CHAMFERING TOOLS
CIRCUIT BEVELERCHAMFERING
Chamferingof cast molds
Surfacechamferingof pre-weldedshaped steelparts
15-16
Chamferingof steel plates
Chamferingof largeworkpieces
PORTABLE CHAMFERING TOOLS
BEVELERMINI BEVELER
CHAMFERING
PORTABLE MAGNETIC BASE DRILLING MACHINE
ATRA ACEmanual feed (WOJ-3200 / W0-3200)
BORING
6
7
Drilling holesin shapedsteel
Drilling holesin steel
Speedy, highprecisionhole drilling
Speedy, highprecisionhole drilling
Drilling holesin shapedsteel
Drilling holesin steel
Speedy, highprecisionhole drilling
Speedy, highprecisionhole drilling
PORTABLE MAGNETIC BASE DRILLING MACHINE
ATRA ACEmanual feed (AO-5575)
BORING
PORTABLE MAGNETIC BASE DRILLING MACHINE
ATRA ACEquick auto
ATRA ACEmanual feed
BORING
9-10
Drilling oflarge andsmalldiameterholes in steel
Drilling holesDrilling holesin steel
Drilling oflarge andsmalldiameterholes in steel
ANNULAR CUTTERS
BROACH CUTTERS &BROACH HOLDERS
BORING
Home boringfor jigattachment
Initial boringfor sheetcutting bywelder
8
Bring ofshaped steel,drilling atelevated site
Variousboring
DrillingPrecisionboring offlanges
PORTABLE MAGNETIC DRILL STAND
ATRA MASTERBORING
8
PORTABLE MAGNETIC BASE DRILLING MACHINE
BORING
Power Tools, delvo, Spring Balancer, Linear Motor Driven Free Piston System 17
CUPLA Series / Mini Cupla Super 18
2
Model WA-3500 Model WA-5000
High-performance mechanism & high-tech components
Mounting the cutter Removing the cutter
One-touch cutter replacementReplacement is quick and easy with ourunique push fit self-centeringcutter system.
Coolant into the Heart of the cutCoolant is fed directly to the inside of thecut. The coolant system also features anauto shut-off.
Fail-Safe ProtectionBuilt-in motion sensorIf any lateral movement or excess vibration is detected, both the drill andthe feed motor stop instantly. Nitto Kohki is the first company toincorporate this feature into magnetic base drills.
Fail-safe restartThe drill will not re-start even if power is re-supplied after accidentalshutdown. Drilling can only be continued after turning on the drill switch.
Magnet open-circuit sensorThe drill will not start until the magnetic field is active.
237 mm
425 mm
613 mm
409 mm
237 mm
535 mm
Max. plate thickness 75 mm
Portable Magnetic Base Automatic Drilling MachineATRA ACE auto
3
JETBROACH One-touch Type35L
JETBROACH One-touch Type50L
HI-BROACH One-touch Type25L
TB01507Cutting Oil
2 L per can
JETBROACH One-touch Type75L
TB01507Cutting Oil
2 L per can
On-site hole-cuttingOn-site hole-cutting in steel plates,H-Beams shapes, shaped bars,framework, and other machinery,shipbuilding, bridges and structures,etc. steel reinfocements andconstruction materials.
Rod handle
ON
New drill control prevents cutters from breaking
Standard Accessories
• Pilot Pin 08035 A2 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set• 3 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can• Plastic Case : 1 pc. • Guard Ass'y : 1 set
• Pilot Pin 08050 A3 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set• 3 mm / 4 mm Hex Socket Screw Key : each 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can• Plastic Case : 1 pc. • Guard Ass'y : 1 set
Optional Accessories
Always use genuine Nitto Kohkicutters & coolant.
JETBROACH One-touch Type25L,35L,50L
HI-BROACH One-touch Type25L,50L
Always use genuine Nitto Kohkicutters & coolant.
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
No Load Speed min-1 (rpm)
Magnet Power Consumption W
Hole-cutting Capacity
One-touch type JETBROACH 25L
One-touch type JETBROACH 35L
One-touch type JETBROACH 50L
One-touch type JETBROACH 75L
One-touch type HI-BROACH 25L
One-touch type HI-BROACH 50L
Magnet Holding Power N (kgf)
Magnet Dimensions mm
Mass (Weight) kg
WA-3500
1,100
950
34
7,056 (720)
92 x 216
20
WA-5000
1,150
350 / 650
75
9,800 (1,000)
101 x 201
23
110 - 120 V AC, 50/60 Hz
10.2
Hole Diameter
-
17.5 to 35 mm
17.5 to 35 mm
-
14 to 35 mm
-
220 - 240 V AC, 50/60 Hz
5.1
Plate Thickness
-
9 to 35 mm
9 to 35 mm
-
9 to 25 mm
-
110 - 120 V AC, 50/60 Hz
10.8
Hole Diameter
12 to 17 mm
17.5 to 40 mm
12 to 50 mm
17.5 to 50 mm
14 to 50 mm
14 to 50 mm
220 - 240 V AC, 50/60 Hz
5.4
Plate Thickness
9 to 25 mm
9 to 35 mm
9 to 50 mm
9 to 75 mm
9 to 25 mm
9 to 50 mm
Slow start mechanismThe feed speed is reduced for the first few seconds after boringbegins to ensure a smooth cut through the mill scale.
Auto-feedAutomatic control & feed are activated by simplypushing the rod handle to engage the gears.
Load sensorThe dual sensing system responds toboth drilling and feeding forces on thecutter for the optimum cutting condition.
Variable speedThe feed speed is continuously monitored andupdated proportionally to the load on the cutter.
Cycle stopAfter the cut has finished, a detector responds to the reduction inload and both the drill and the feed motor automatically stop.
Overload stopWhen an excessive load is applied to the cutter, both the drill and thefeed motor will stop automatically to prevent the cutter from breaking.
Portable Magnetic Base Automatic Drilling MachineATRA ACE auto
4
Designd to use Jetbroach Carbide Tipped Annular Cutters
Designd to use High Speed Steel Annular Cutters
Portable Magnetic Base Drilling MachineATRA ACE WOJ-3200/WO-3200
Manual feed
WOJ-3200Manual feed
WOJ-3200
Manual feed WO-3200
Standard Accessories • Pilot Pin 08050 : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Side Handle Assy’s : 1 set• Safety Strap : 1 pc.• Guard Ass'y : 1 set
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption
Rated Current
No Load Speed
Magnet Power Consumption
Hole-cutting Capacity
Magnet Holding Power
Magnet Dimensions
Mass (Weight)
W
A
min-1 (rpm)
W
One-touch type HI-BROACH
kN (kgf)
mm
kg
WO-3200
220 - 240 V AC, 50/60 Hz
950
4.3
530
70
9 (918)
99 x 177
13
Hole Diameter
12 to 32 mm
Plate Thickness
9 to 50 mm
Standard Accessories • Pilot Pin 08050 : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 6 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Safety Strap : 1 pc.• Sub Handle : 1 pc.• Guard Ass'y : 1 set
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption
Rated Current
No Load Speed
Magnet Power Consumption
Hole-cutting Capacity
Magnet Holding Power
Magnet Dimensions
Mass (Weight)
W
A
min-1 (rpm)
W
One-touch type JETBROACH
kN (kgf)
mm
kg
WOJ-3200
220 - 240 V AC, 50/60 Hz
950
4.3
870
70
9 (918)
99 x 177
13
Hole Diameter
12 to 32 mm
Plate Thickness
9 to 50 mm
318 mm99 mm
361 mm
Reversible Feed HandlesFeed handles can be positioned on the rightor left hand side for ease of drilling and mounting in confined spaces.
Optional One-Touch AdapterOptional one-touch adapter allowsthe use of up to 13 mm twistdrills to be used in theoriginal arbor.
Optional Jet Oiling SystemOptional jet oiling system for use with all drilling applications and types of cutters to extend cutter life and increase hole output.
Optional Chip BreakerOptional chip breaker helps prevent the cutter from plugging the hole with chip debris, causing some false overloadsand cutter life loss.
Body Height Adjustment
60 mm
The world's first manual feed with ''Smart-Stop / Rapid-Restart'' technology for WOJ-3200 / AO-5575
This new feature is a breakthrough in the Manual drill industry. Formerly only found on high end Nitto Kohki Automatic drills, this technology displays the current drill status via the LED Load Indicator. Customers will experience a cutting edge drill management system designed solely around saving time and money in replacement parts and cutters in addition to reducing user fatigue and downtime.
Model WOJ-3200 Model AO-5575
LoadIndicator
361 mm
Loosening the pillar clamp allows thecomplete frame to be lifted up to a maximum of 60 mm for specific drilling. The use of Hi-Broach cutters require the frame to be at the lowest position, while twist bit drilling required the appropriate amount of elevation to be adjusted for safe operation. The pillar clamp is required to be tightened before safe drilling may take place. Note: Always engage the magnet before adjusting the body height.
Newly developed Over-Load Shutdown, Magnet Open-Circuit Sensor, and Fail-Safe Restart technology formerly only found on high-end Nitto Automatics are incorporated on the machine.(Smart-Stop / Rapid-Restart feature is not included.)
318 mm99 mm
5
Portable Magnetic Base Drilling MachineATRA ACE WOJ-3200/AO-5575
Manual feed
AO-5575Manual feed
AO-5575
Standard Accessories• Pilot Pin 08050 A3 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set
• 3 mm Hex Socket Screw Key : 1 pc.• 5 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.
• Cutting Oil 0.5 L : 1 can• Guard Ass'y : 1 set
Optional Accessories
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
No Load Speed min-1 (rpm)
Magnet Power Consumption W
Hole-cutting Capacity
One-touch type JETBROACH
One-touch type HI-BROACH
Magnet Holding Power kN (kgf)
Magnet Dimensions mm
Mass (Weight) kg
AO-5575
220 - 240 V AC, 50/60 Hz
1,150
5.4
350 / 650
50
10 (1,020)
86 x 170
18
Hole Diameter
12 to 55 mm
12 to 50 mm
Plate Thickness
9 to 75 mm
9 to 50 mm
296 mm86 mm
611 mm
"Smart Stop"Fast Blinking Red
Slow Blinking Green
Green / Orange
RedOrangeGreen
Resume proper load
“Smart Stop” stalls motor when overloaded.
Proper load
LED load indicator
Overload
“Rapid-Start” resumes drilling operation
Drill motor shuts off
Drill motor will not turn on
Continued overload
Slow Blinking Red
Magnet malfunction
Load detector with “Smart-Stop/Rapid-Restart” technology
"SmFast
"Smart Stop"Fast Blinking Red
"Smart Stop"Fast Blinking Red
Safety mode
As the drilling load increases, the load indicator will change in color from green to orange to red. In addition, if excessive feeding force is applied, the load indicator will rapidly blink red and the rotation of the drill motor will slow down and temporarily stop. If the load is released while the load indicator is blinking red, the drill motor will resume its rotation.
Designd to use Jetbroach and Hi-broach Annular Cutters
HI-BROACH One-touch Type25 mm, 50 mm
JETBROACH One-touch Type25 mm, 35 mm,50 mm, 75 mm
TB01507Cutting Oil
2 L per canAlways use genuine NittoKohki cutters & coolant.
Low Speed
Optional Chip BreakerThis chip breaker prevents the cutter from becomingjammed with metal shavings.
Hi Speed
Coolant ValveAdjustable coolant flowdelivered to the centerof the cutter.
Speed selection (Change gear)
Reversible feed handle
Model AO-5575
MAX. 55 mm dia. x 75 mm deepLIGHT WEIGHT 18 kg
Built-in coolanttank preventsdamage
One-touch cutter replacementOur original self-centering tool-less chuck is quick and easyto change cutters with little downtime. (WOJ-3200)
Mounting the cutter Removing the cutter Mounting the twist drill
6
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
No Load Speed min-1 (rpm)
Magnet Power Consumption W
Hole-cutting Capacity
One-touch type JETBROACH 35L
One-touch type JETBROACH 50L
One-touch type HI-BROACH 25L
Magnet Holding Power N (kgf)
Magnet Dimensions mm
Mass (Weight) kg
QA-4000
680
750
50
6,664 (680)
82 x 172
18.5
QA-6500
220 - 240 V AC, 50/60 Hz
1,010
4.5
400 / 750
75
9,800 (1,000)
100 x 200
26
115 V AC, 50/60 Hz
6.1
Hole Diameter
17.5 to 40 mm
-
14 to 15 mm
16 to 18 mm
220 - 240 V AC, 50/60 Hz
3.0
Plate Thickness
9 to 35 mm
-
9 to 12 mm
9 to 25 mm
Hole Diameter
17.5 to 40 mm
17.5 to 65 mm
18 to 35 mm
-
Plate Thickness
9 to 35 mm
9 to 50 mm
9 to 25 mm
-
Standard Accessories
• Pilot Pin 08035 A2 : 1 pc. • Chain : 1 pc• 3 mm Hex Socket Screw Key : 1 pc.• 4 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Side Handle : 1 pc. • Oil Tank Ass'y : 1 set.
• Pilot Pin 08050 A3 : 1 pc. • Chain : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 4 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Chip Stopper : 1 pc. • Side Handle : 1 pc.• Oil Tank Ass'y : 1 set.
ATRA ACE quick auto
Designd to use Jetbroach and Hi-broach Annular Cutters
quick autoquick auto Self feedingLoad detection
Limit SwitchAutomatic return
Automatic step feedEmergency stop
Precisionbearing bracketaligns cutters precisely, which increases cutter life.
Chip breaker prevents swarf and chip nesting.
Automatic return
QUICK AUTO Drills increase productivity and reduce hole drilling cost.Proven Automatic Tecnology
Bearing Bracket
Chip Breaker
Once drilling is completed and the slug is ejected from the hole, the cutting bit is quickly retracted. This quick drill motor retraction allows the user to move onto the next hole more quickly.
Self feeding & Load detection The feeding is controlled by an onboard microcomputer. The feed rate begins slowly and then increases to the appropriate speed for the cutter size and load condition. The load detector clearly shows the amount of resistance on the cutter at anytime.
Limit Switch When the drill has reached to the top of its stroke, a limit switch stops the drill motor. There is also a limit switch at the bottom of drill stroke .
One-touch Cutter Replacement!One-Touch arbor system requires no tools for cutter installation and removal.
Improved Feature
Side Slip Detection Function
Step feed feature optimizes cutter penetration.
This feature automatically stops the drill from operating when sudden lateral force is applied to the machine.
Automatic Step Feed (QA-6500)
Red Green Yellow Orange Red
ON STOPLOADLOAD DETECTOR
535 mm
215 mm 454.5 mm
49 mm
425 mm
215 mm 407 mm
49.5 mm
Light up
ON STOPLOADLOAD DETECTOR
Built-in motion detection sensor
7
Portable Magnetic Base Drilling Machine
N.B. : The electric drill and drill mount fixture do not come with ATRA MASTERs.
Portable Magnetic Base Drilling Machine
The magnet bases of ATRA MASTER hold the drills perpendicular to steel plates even on non horizontal places.
Drilling Capacity : 10 mm Drilling Capacity : 13 mmPower Source (Single Phase) : 220 - 240 V AC, 50/60 Hz
Drilling Capacity : 25 mmPower Source (Single Phase) : 220 - 240 V AC, 50/60 Hz
Drilling Capacity : 32 mmPower Source (Single Phase) : 220 - 240 V AC, 50/60 Hz
Portable Magnetic Drill StandATRA MASTER
The largest capacity drilling machine in the Nitto Kohki line.
Max. Hole-cutting Capacity : 100 mm dia.Max. Plate Thickness : 75 mm
Side-lock Type Cutter
575 mm
318 mm 705 mm
73.5 mm
Mass (weight) : 6.2 kg Mass (weight) : 16 kg Mass (weight) : 25.5 kg Mass (weight) : 29 kg
Power Source (Single Phase) : 220 - 240 V AC, 50/60 Hz
Specifications
ElectricDrill
Cutter
Model
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
No Load Speed min-1 (rpm)
Magnet Power Consumption W
Hole-cutting Capacity
Side-Lock type JETBROACH 75L
Magnet Holding Power N (kgf)
Magnet Dimensions mm
Mass (Weight) kg
A-100
220 - 240 V AC, 50/60 Hz
1,600
7.4
330
80
17,640 (1,800)
130 x 256
50
Hole Diameter
50 to 100 mm
Plate Thickness
13 to 75 mm
Standard Accessories
• Pilot Pin 12075 : 1 pc. • Chain : 1 pc• 2 mm / 2.5 mm / 3 mm / 4 mm / 5 mm / 6 mm / 8 mm Hex Socket Screw Key : each 1 pc.• 7 x 8 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Oil Cap Ass'y : 1 set. • Rod Handle : 3 pcs.
Designed to use Jetbroach Carbide Tipped Annular Cutters
manual feedmanual feed
8
ATRA ACE manual feed
12131415161717.5181919.5202121.52222.52323.52424.525262728293031323334353637383940414243444546474849505152
25mm
mm50
TK00698TK00699TK00700TK00701TK00702TK00703TK00335TK00336TK00337TK00338TK00339TK00340TK00341TK00342TK00343TK00344TK00345TK00346TK00347TK00348TK00349TK00351TK00352TK00353TK00354TK00355TK00356TK00357TK00359TK00361TK00704TK00705TK00706TK00707TK00708TK00709TK00710TK00711TK00712TK00713TK00714TK00715TK00716TK00717TK00718TK00719TK00720
Depth PN WO
-320
0
AO-5
575
WA-
3500
WA-
5000
QA-
4000
QA-
6500
HI-BROACH
mmdia.
1213141516171819202122232425262728293031323334353637383940414243444546474849505152
TK00721TK00722TK00723TK00724TK00725TK00726TK00727TK00728TK00729TK00730TK00731TK00732TK00733TK00734TK00735TK00736TK00737TK00738TK00739TK00740TK00741TK00742TK00743TK00744TK00745TK00746TK00747TK00748TK00749TK00750TK00751TK00752TK00753TK00754TK00755TK00756TK00757TK00758TK00759TK00760TK00761
Depth PN WO
-320
0
AO-5
575
WA-
5000
mmdia.BROACH CUTTERS are far better than twist drills:
• No dead point• Peripheral cutting• Blade cutting resistance reduced by 50 %• Available diameter size: 12 - 100 mm
Test Drilling is very often the only way todetermine the machinability of difficultmaterials. Use a small size cutterwherever possible in order tominimize trial costs.
Industrial cutters for faster and better finished holes.• The Spring-loaded pilot pin picks up the hole location quickly, and ejects the slug automatically at the end of cut• Available with No. 2 - 4 Morse taper shanks• Oil cup complete Ass'y (PN TB00350) is available as an optional attachment which provides continuous and adjustable cutting oil flow to the cutting area
Morse Taper No.
M.T.No.2
M.T.No.3
M.T.No.4
BHM-02035TB00390
163 mm
BHM-03050TB00392
BHM-13075 TB00352
BHM-14075TB00354
Model Cutter
HBO-25L12 - 17 dia.
Optional
Optional
Optional
Standard
Standard
Standard
06025 (PN TK01167)
08025 (PN TJ12696)
08035 (PN TJ15859)
17.5 - 35 dia.
17.5 - 35 dia.
12 - 17 dia.
17.5 - 52 dia.
12 - 18 dia.
19 - 52 dia.
17.5 - 40 dia.
17.5 - 65 dia.18 - 35 dia.
06025 (PN TK01167)
08025 (PN TJ12696)
06050 (PN TK01166)
0850 (PN TK00802)
08050 (PN TJ16019)
08035 (PN TJ15859)
08050 (PN TJ16019)
JBO-35L
HBO-25L
HBO-50L
JBO-35L
JBO-50LJBO-50L(W)
JBS-75L 50 - 100 dia.12075
(PN TA9A207)
Cutter Diameter Pilot Pin Accessory
65 mm(12 - 19.5 dia.)
58 mm(20 - 52 dia.)
65 mm(25L)73 mm(35L)
95 mm(12 - 17 × 50L)90 mm(17.5 - 65 × 50L)
For stacked two plates.
156 mm
Hole-cuttingCapacity
Feed Speed mm/revCircumferential Speed m/min
HI-BROACHOne-touch Type / 25L
25L : 12 - 52 dia.---
25L : 25---
86 mm
HI-BROACHOne-touch Type / 50L
--
50L : 12 - 52 dia.---
50L : 50-
JETBROACHOne-touch Type / 25,35,50L
JETBROACHOne-touch Type / 50L(W)
25L : 2535L : 3550L : 50-
--
50L(W) : 18,22,24 - 26.5,28,32, and 35 dia.
--
50L(W) : 50-
JETBROACHOne-touch Type / 75L
--
75L : 17.5 - 55 dia.----
75L : 75
JETBROACHSide lock Type / 75L
--
75L : 50 - 100 dia.----
75L : 75
117 mm90 mm
25L : 12 - 17 dia.35L : 17.5 - 40 dia.50L : 12 - 65 dia.
-
182 mm
248 mm
232 mm
One-touch TypeHI-BROACH
One-touch Type
Hole Diameter mm
Plate Thikness mm
0.02 - 0.115 - 35 (mild steel) 35 - 50 (mild steel)
9
JETBROACH CUTTERS & HI-BROACH CUTTERS
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Combination of Pilot Pins & Broach Cutters
12075 PN : TA9A207 JBS 50 - 100 dia.Depth 75 mm
192 mm
08035 PN : TJ15859 JBO 17.5 - 40 dia.Depth 35 mm
91 mm8 dia.
08050 PN : TJ16019
112 mm8 dia.
6dia.
Annular CuttersJETBROACH CUTTERS & HI-BROACH CUTTERS
HBO 12 - 17 dia.Depth 25 mm
HBO 17.5 - 52 dia.Depth 25 mm
06025 PN : TK01167
08025 PN : TJ12696
Pilot Pin HI-BROACH Cutters Pilot Pin JETBROACH Cutters
Pilot Pin JETBROACH Cutters
81 mm
5 dia.
8 dia.76 mm
HBO 12 - 18 dia.Depth 50 mm
HBO 19 - 52 dia.Depth 50 mm
06050 PN : TK01166
0850 PN : TK00802
5 dia.6.35 dia.
6.35 dia. 6.35 dia.
112 mm
06050 PN : TK01166
5 dia.6.35 dia.
112 mm
7 dia.8 dia.
100 mm
JBO 12 - 17 dia.Depth 25 mm
JBO 12 - 17 dia.Depth 50 mm
06025 PN : TK01167
81 mm
5 dia.
JBO 17.5 - 65 dia.Depth 50 mm
08075 PN : TJ17436
133 mm
JBO(W) 18 - 35dia.Depth 50 mm for stacked two (=W) plates.
JBO 17.5 - 55 dia.Depth 75 mm
08050 PN : TJ16019
112 mm8 dia.
8 dia.
Pilot Pin JETBROACH Cutters
10
12131415161717.5181919.52020.52121.52222.52323.52424.5252626.5272829303132333435363738394041424344454647484950515253545556575859606162636465
TK01154TK01155TK01156TK01157TK01158TK01159TK00380TK00381TK00382TK00383TK00384TK00385TK00386TK00387TK00388TK00389TK00390TK00391TK00392TK00393TK00394TK00395TK00396TK00397TK00398TK00399TK00400TK00401TK00402TK00403TK00404TK00405TK00406TK00407TK00408TK00409TK00410TK00411TK00412TK00413TK00414TK00415TK00416TK00417TK00418TK00419TK00420TK00442TK00443TK00444TK00445TK00446TK00447TK00448TK00449TK00450TK00451TK00607TK00608TK00609TK00610TK00611
Depth PN WO
J-32
00
AO-5
575
WA-
3500
WA-
5000
QA-
6500
mmdia.
17.51819202122232425262728293031323334353637383940414243444546474849505152535455
TK01036TK01003TK01004TK01005TK01006TK01007TK01008TK01009TK01010TK01011TK01012TK01013TK01014TK01015TK01016TK01017TK01018TK01019TK01020TK01021TK01022TK01023TK01024TK01025TK01026TK01027TK01028TK01029TK01030TK01031TK01032TK01033TK01034TK01035TK01112TK01113TK01114TK01115TK01116
Depth PN AO-5
575
WA-
5000
mmdia.
5051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100
TJ17709TJ16651TJ16652TJ16653TJ16654TJ16655TJ16656TJ16657TJ16658TJ16659TJ16660TJ16661TJ16662TJ16663TJ16664TJ16665TJ16666TJ16667TJ16668TJ16669TJ16670TJ16671TJ16672TJ16673TJ16674TJ16675TJ16676TJ16677TJ16678TJ16679TJ16680TJ16681TJ16682TJ16683TJ16684TJ16685TJ16686TJ16687TJ16688TJ16689TJ16690TJ16691TJ16692TJ16693TJ16694TJ16695TJ16696TJ16697TJ16698TJ16699TJ16700
Depth PN A-10
0
mmdia.
12131415161717.5181919.52020.52121.52222.52323.52424.5252626.52728293031323334353637383940
TK01148TK01149TK01150TK01151TK01152TK01153TK00301TK00302TK00304TK00305TK00306TK00307TK00308TK00309TK00310TK00311TK00312TK00313TK00314TK00315TK00316TK00317TK00318TK00319TK00320TK00321TK00322TK00323TK00324TK00325TK00326TK00328TK00602TK00603TK00604TK00605TK00606
Depth PN WO
J-32
00
AO-5
575
WA-
3500
WA-
5000
QA-
4000
QA-
6500
mmdia.
25
35
50
75
75
mm
mm
JETBROACHOne-touch Type
18222424.5252626.5283235
TK01068TK00622TK00623TK00631TK00624TK00625TK00632TK00626TK00627TK00628
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Depth PN WO
J-32
00
AO-5
575
mmdia.
50L for stacked two(=W) plates.
50mm
mm
mm
mm
JETBROACHOne-touch Type
JETBROACHOne-touch Type
JETBROACHOne-touch Type
JETBROACHSide-lock Type
Max. Punching Thickness : 13 mm
Max. Punching Diameter : 22 mm
Max. Throat Depth : 60 mm
New design adopted for punching stainless steel.Inching function (manual operation) is available.
SpecificationsModel
Power Source (Single Phase)
Max. Output Pressure MPa (kgf/cm2)
Output
At No Load L/min
At 68.65 MPa L/min
Motor
Reservoir Capacity L
Discharge Port
Electro-Magnetic Valve
Mass (Weight) kg
HPD-05
115 V / 230 V AC
68.65 (700)
0.4 kW 4P
4.0
Rc 3/8
4 way 3 position valve
32.5
50 Hz
1.20
0.55
60 Hz
1.44
0.66
Standard Accessories
• Hose Kit Ass'y : 1 set • Hose Cord Ass'y : 1 set• 4 mm / 5 mm Hex. Socket Screw Key : Each 1 pc.• Spanner : 1 pc. • Spanner 12 : 1 pc.• Sub Handle Ass'y : 1 set• Chip Guard Ass'y : 1 set • Tool Box : 1 pc.• D Punch / Die 22 mounted on machine
• Hose Kit Ass'y : 1 set • Hose Cord Ass'y : 1 set• 4 mm / 5 mm Hex. Socket Screw Key : Each 1 pc.• Spanner : 1 pc. • Spanner 12 : 1 pc.• Sub Handle Ass'y : 1 set• Chip Guard Ass'y : 1 set • Tool Box : 1 pc.• D Punch / Die 22 mounted on machine
• Hose Kit Ass'y : 1 set • Hose Cord Ass'y : 1 set• 4 mm / 5 mm Hex. Socket Screw Key : Each 1 pc.• Spanner : 1 pc. • Spanner 12 : 1 pc.• Sub Handle Ass'y : 1 set• Chip Guard Ass'y : 1 set • Tool Box : 1 pc.• D Punch / Die 22 mounted on machine
PNTB02506TP05184TB02390TP05777
Part NameHose Kit Ass'y 5 mUltra-high pressure hose 5 mSwitch Cord Ass'y 5 mUltra-high pressure hose 10 m
Unit1 set1 pc.1 set1 pc.
Model
HS series
PNTB02545TB02141TA92729TB02142
Part NameSwitch Cord Ass'y 10 mFoot Switch Ass'yOil Can Ass'yHook Clamp Ass'y
Unit1 set1 set1 set1 set
Model
HS seriesOptional Parts
323 mm
423 mm
for SELFER ACE
415 mm
426.4 mm
Max. Punching Thickness : 16 mm
Max. Punching Diameter : 24 mm
Max. Throat Depth : 70 mm
363 mm
430.5 mm
Max. Punching Thickness : 16 mm
Max. Punching Diameter : 24 mm
Max. Throat Depth : 110 mm
385 mm
462.5 mm
Double-Acting
24 mm
Dimension fromedge to PunchCenter
HS06, HS07, HS11
SpecificationsModel
Max. Throat Depth mm
Punching Capacity
Max. Punching Thickness mm
Max. Punching Diameter mm
Hole Making Time
Allowable Max. Pressure MPa (kgf/cm2)
Max.Output kN (tf)
Ram Stroke mm
Mass (Weight) kg
HS06-1322
60
Punching Time 7.9 sec.
Returning Time 3.4 sec.
68.65 (700)
367 (37)
21
20.5
for Mild Steel
13
22
for Stainless Steel
6
22
HS07-1624
70
Punching Time 11.8 sec.
Returning Time 5.7 sec.
68.65 (700)
464 (47)
25
25.5
for Mild Steel
16
24
for Stainless Steel
6
24
HS11-1624
110
Punching Time 11.8 sec.
Returning Time 5.7 sec.
68.65 (700)
464 (47)
25
30
for Mild Steel
16
24
for Stainless Steel
6
24
In case of mild steel maximum punching thickness must be decided based on the equation of 0.8 x punching diameter. For details see the instruction manual.
Portable Double-Acting Hydraulic PuncherSELFER ACE
11
Single-Acting
Max. Punching Thickness : 13 mm
Max. Punching Diameter : 22 mm
Max. Throat Depth : 60 mm
Punch, return, and reset operations are fully automatic.An emergency switch stops the punch instantly at any time.
SpecificationsModel
Power Source (Single Phase)
Max. Output Pressure MPa (kgf/cm2)
Output
At No Load L/min
At 68.65 MPa L/min
Motor
Reservoir Capacity L
Discharge Port
Mass (Weight) kg
SC-05
115 V / 230 V AC
68.65 (700)
0.4 kW 4P
4.0
Rc 3/8
27.5
50 Hz
1.20
0.55
60 Hz
1.44
0.66
381 mm
524.1 mm
324 mm
380 mm
Max. Punching Thickness : 16 mm
Max. Punching Diameter : 24 mm
Max. Throat Depth : 70 mm
418 mm
545.6 mm
Max. Punching Thickness : 16 mm
Max. Punching Diameter : 24 mm
Max. Throat Depth : 110 mm
436 mm
545.6 mm
24 mm
Dimentionfrom edgeto punch center
HA06, HA07,HA11
Standard Accessories
• Sub Handle Ass'y : 1 set• Hose Cord Ass'y : 1 set• 4 mm Hex. Socket Screw Key : 1 pc.• Spanner : 1 pc.• Tool box : 1 pc.• D Punch / Die 22 mounted on machine
• Sub Handle Ass'y : 1 set• Hose Cord Ass'y : 1 set• 4 mm Hex. Socket Screw Key : 1 pc.• Spanner : 1 pc.• Tool box : 1 pc.• D Punch / Die 22 mounted on machine
• Sub Handle Ass'y : 1 set• Hose Cord Ass'y : 1 set• 4 mm Hex. Socket Screw Key : 1 pc.• Spanner : 1 pc.• Tool box : 1 pc.• D Punch / Die 22 mounted on machine
SpecificationsModel
Max. Throat Depth mm
Punching Capacity
Max. Punching Thickness mm
Max. Punching Diameter mm
Hole Making Time
Allowable Max. Pressure MPa (kgf/cm2)
Max.Output kN (tf)
Ram Stroke mm
Mass (Weight) kg
HA06-1322
60
for Mild Steel
13
22
10.5 sec.
68.65 (700)
304 (31)
21
21.5
HA07-1624
70
for Mild Steel
16
24
16.5 sec.
68.65 (700)
431 (44)
25
28.5
HA11-1624
110
for Mild Steel
16
24
16.5 sec.
68.65 (700)
431 (44)
25
35.5
In case of mild steel maximum punching thickness must be decided based on the equation of 0.8 x punching diameter. For details see the instruction manual.
PNTA96534TP05184TA93778TA9B044TP05777
Part NameHose Kit Ass'y 5 mUltra-high pressure hose 5 mSwitch Cord Ass'y 5 mHose Kit Ass'y 10 mUltra-high pressure hose 10 m
Unit1 set1 pc.1 set1 set1 pc.
Model
HA series
PNTA95307TA94386TA92729
TA96342
Part NameSwitch Cord Ass'y 10 mFoot Switch Ass'yOil Can Ass'y
Hook Clamp Ass'y
Unit1 set1 set1 set
1 set
Model
HA series
HA07-1624HA11-1624
Optional Parts
Portable Single-Acting Hydraulic PuncherSELFER HA Type
12
Built-in hydraulic pump shows its power in making roundor elongated holes in flat bar, angle bar or channel iron
SpecificationsModel
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
Max. Punching Diameter mm
Max. Punching Thickness mm
Max. Throat Depth mm
Punching Time sec (single pass)
Power Cord m
Mass (Weight) kg
E25-0615
220 - 240 V AC, 50/60 Hz
305
1.6
15
6
25
4
2.4
7.0
Motor
E55-0619
19
6
55
2
2.4
14
115 V AC, 50/60 Hz
670
6.0
220 - 240 V AC, 50/60 Hz
670
3.0
Standard Accessories
• E Punch 15 : 1 pc.• E Die 15A : 1 pc.• E Die 15B : 1 pc.• Spanner 8 : 1 pc.• 10 x 12 mm Spanner : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 4 mm Hex. Socket Screw Key : 1 pc.• Auxiliary Oil : 1 pc.
• EL Punch 18 : 1 pc.• EL Die 18A : 1 pc.• EL Die 18B : 1 pc.• Spanner 10 x 12 mm : 1 pc.• 3 mm Hex. Socket Screw Key : 1 pc.• 4 mm Hex. Socket Screw Key : 1 pc.• 5 mm Hex. Socket Screw Key : 1 pc.• Stand Ass’y : 1set• Auxiliary Oil : 1 pc.
Optional AccessoryPN
TB00800
Part Name
Stand Ass'y
Sales Unit
1 set
Application
For thin sheets
For thick sheets
For thin sheets
For thick sheets
For channel iron
Type of Die
A
B
A
B
C
Model
E25-0615
E55-0619
Plate Thickness (mm)
Mild Steel
2 - 3.2
4 - 6
2 - 3.2
4 - 6
7 - 8
Stainless Steel
Max. 3
Max. 4
Max. 3
Max. 4
-
Selection of Dies
A= 7
5~12
5
t=Plate thickness
B=40~65
t1 B-t12
Punching Capacity in channel iron (E55-0619)
10 OD 11 OD 12 OD 13 OD 14 OD 15 OD 16 OD
75 x 40 t7
100 x 50 t7.5
125 x 65 t8
Punching Dia.
Size
Max.Punching Thickness : 6mm
Max.Punching Diameter : 15 mm
Max.Throat Depth : 25 mm
340.5 mm
357 mm
Max.Punching Thickness : 6mm
Max.Punching Diameter : 19 mm
Max.Throat Depth : 55 mm
420 mm
368 mm
Electrically Operated Hydraulic PuncherHANDY SELFER
13
Elongatedhole Punch
Roll Pin
Jig
Elongatedhole Die
Punches & Dies for SELFER Puncher
FOR HS06-1624/HS07-1624/HS11-1624/HA06-1624/HA07-1624/HA11-1624
PNTJ10778TJ11088TJ06700TJ06698TJ06696TJ06694TJ06692TJ06611TJ06690TJ06688TJ06686TJ06609TJ06684TJ06682TJ06680TJ06607TJ06678TJ07979TJ06676TJ06674TJ06566TJ07748TJ10061
Round hole D Punch
SizeD Punch 8D Punch 9D Punch 10D Punch 11D Punch 12D Punch 13D Punch 14D Punch 14.5D Punch 15D Punch 16D Punch 17D Punch 17.5D Punch 18D Punch 19D Punch 20D Punch 20.5D Punch 21D Punch 21.5D Punch 22D Punch 23D Punch 23.5D Punch 24D Punch 25
PNTK00242TK00243TK00244TK00245TK00246TK00247TK00248TK00249TK00250TK00251TK00252TK00253
Elongated hole E Punch
SizeEL Punch 10 x 6.5EL Punch 13 x 6.5EL Punch 13 x 8.5EL Punch 13.5 x 9EL Punch 15 x 10EL Punch 16.5 x 11EL Punch 17 x 8.5EL Punch 18 x 9EL Punch 18 x 12EL Punch 19.5 x 13EL Punch 20 x 10EL Punch 21 x 14
PNTK00254TK00255TK00256TK00257TK00258TK00259TK00260TK00261TK00262TK00263TK00264TK00265
Elongated hole E Die(Type A for thin sheets)
SizeEL Die 10 x 6.5AEL Die 13 x 6.5AEL Die 13 x 8.5AEL Die 13.5 x 9AEL Die 15 x 10AEL Die 16.5 x 11AEL Die 17 x 8.5AEL Die 18 x 9AEL Die 18 x 12AEL Die 19.5 x 13AEL Die 20 x 10AEL Die 21 x 14A
PNTK00266TK00267TK00268TK00269TK00270TK00271TK00272TK00273TK00274TK00275TK00276TK00277
Elongated hole E Die(Type B for thick sheets)
SizeEL Die 10 x 6.5BEL Die 13 x 6.5BEL Die 13 x 8.5BEL Die 13.5 x 9BEL Die 15 x 10BEL Die 16.5 x 11BEL Die 17 x 8.5BEL Die 18 x 9BEL Die 18 x 12BEL Die 19.5 x 13BEL Die 20 x 10BEL Die 21 x 14B
PNTJ10779TJ11089TJ06701TJ06699TJ06697TJ06695TJ06693TJ06612TJ06691TJ06689TJ06687TJ06610TJ06685TJ06683TJ06681TJ06608TJ06679TJ07980TJ06677TJ06675TJ06569TJ07749TJ10062
Round hole D Die
SizeD Die 8D Die 9D Die 10D Die 11D Die 12D Die 13D Die 14D Die 14.5D Die 15D Die 16D Die 17D Die 17.5D Die 18D Die 19D Die 20D Die 20.5D Die 21D Die 21.5D Die 22D Die 23D Die 23.5D Die 24D Die 25
•TA99037 Lock Nut Ass'y is reguired for D Punch 25
30
60
D Punch
42
16.5
D Dies
FOR E25-0615
PNTK00100TK00102TK00143TK00105TK00146TK00111TK00149TK00117TK00120TK00123TK00097TK00167TK00428
Round hole E Punch
SizeE Punch 4E Punch 5E Punch 5.5E Punch 6E Punch 6.5E Punch 8E Punch 8.5E Punch 10E Punch 11E Punch 12E Punch 13E Punch 14E Punch 15
PNTK00101TK00103TK00144TK00106TK00147TK00112TK00150TK00118TK00121TK00124TK00098TK00168TK00288
Round hole E Die(Type A for thin sheets)
SizeE Die 4AE Die 5AE Die 5.5AE Die 6AE Die 6.5AE Die 8AE Die 8.5AE Die 10AE Die 11AE Die 12AE Die 13AE Die 14AE Die 15A
PN-
TK00104TK00145TK00107TK00148TK00113TK00151TK00119TK00122TK00125TK00099TK00169TK00429
E Die(Type B for thick sheets)
Size -E Die 5BE Die 5.5BE Die 6BE Die 6.5BE Die 8BE Die 8.5BE Die 10BE Die 11BE Die 12BE Die 13BE Die 14BE Die 15B
PNTK00126TK00158TK00129TK00152TK00155
Elongated hole E Punch
SizeE Punch 10 x 5E Punch 10 x 6.5E Punch 12 x 6E Punch 13 x 6.5E Punch 13 x 8.5
PNTK00127TK00159TK00130TK00153TK00156
Elongated hole E Die(Type A for thin sheets)
SizeE Die 10 x 5AE Die 10 x 6.5AE Die 12 x 6AE Die 13 x 6.5AE Die 13 x 8.5A
PNTK00128TK00160TK00131TK00154TK00157
Elongated hole E Die(Type A for thin sheets)
SizeE Die 10 x 5BE Die 10 x 6.5BE Die 12 x 6BE Die 13 x 6.5BE Die 13 x 8.5B
16
30.5
E Punches
35
Front view ofE Dies Type A
35
Front view ofE Dies Type B
24
Side face ofE Dies Type A
21 : over or equal 8 dia.(19 : under 8 dia.)
27
Side face ofE Dies Type B
21 : over or equal 8 dia.(19 : under 8 dia.)
FOR E55-0619
PNTJ13229TJ13230TJ13231TJ13232TJ13233TJ13234TJ13235TJ13236TJ13237
Elongated hole D Punch
SizeD Punch 16 x 8D Punch 18 x 9D Punch 20 x 10D Punch 22 x 11D Punch 24 x 12D Punch 25 x 9D Punch 25 x 12D Punch 25 x 14D Punch 25 x 18
PNTJ13238TJ13239TJ13240TJ13241TJ13242TJ13243TJ13244TJ13245TJ13246
Elongated hole D Die
SizeD Die 16 x 8D Die 18 x 9D Die 20 x 10D Die 22 x 11D Die 24 x 12D Die 25 x 9D Die 25 x 12D Die 25 x 14D Die 25 x 18
PNTK00455TK00456TK00457TK00458TK00459TK00460TK00461TK00462TK00463
Elongated hole Jig
SizeJig 16 x 8Jig 18 x 9Jig 20 x 10Jig 22 x 11Jig 24 x 12Jig 25 x 9Jig 25 x 12Jig 25 x 14Jig 25 x 18
FOR HS06-1624/HS07-1624/HS11-1624/HA06-1624/HA07-1624/HA11-1624 Optional•TA99037 Lock Nut Ass'y is reguired for Elongated hole D Punch 25 x 9/12/14/18
PNTK00193TK00194TK00195TK00196TK00197TK00198TK00199TK00200TK00201TK00202TK00203TK00204TK00205TK00278TK00180
Round hole EL Punch
SizeEL Punch 6EL Punch 6.5EL Punch 8EL Punch 8.5EL Punch 10EL Punch 11EL Punch 12EL Punch 13EL Punch 14EL Punch 15EL Punch 16EL Punch 17EL Punch 18EL Punch 18.5EL Punch 19
PNTK00208TK00209TK00210TK00211TK00212TK00213TK00214TK00215TK00216TK00217TK00218TK00219TK00220TK00279TK00181
Round hole EL Die(Type A for thin sheets)
SizeEL Die 6AEL Die 6.5AEL Die 8AEL Die 8.5AEL Die 10AEL Die 11AEL Die 12AEL Die 13AEL Die 14AEL Die 15AEL Die 16AEL Die 17AEL Die 18AEL Die 18.5AEL Die 19A
PNTK00222TK00223TK00224TK00225TK00226TK00227TK00228TK00229TK00230TK00231TK00232TK00233TK00234TK00280TK00182
Round hole EL Die(Type B for thick sheets)
SizeEL Die 6BEL Die 6.5BEL Die 8BEL Die 8.5BEL Die 10BEL Die 11BEL Die 12BEL Die 13BEL Die 14BEL Die 15BEL Die 16BEL Die 17BEL Die 18BEL Die 18.5BEL Die 19B
PN----
TK00235TK00236TK00237TK00238TK00239TK00240TK00241----
Round hole EL Die(Type C for channel iron)
Size - - - -EL Die 10CEL Die 11CEL Die 12CEL Die 13CEL Die 14CEL Die 15CEL Die 16C - - - -
22
30.5
EL Punches
40
Front view ofEL Dies Type A, B & C
32
22.5
Side face ofEL Dies Type A, B & C
Sales Unit : 1 Piece
PN
TQ01279
TA99037
Part Name
Hex. Setscrew 8 x 14 for Elongated hole Die
Lock Nut Ass'y for D Punch 25
PUNCHES & DIES
14
Compact portable models meetyour versatile chamfering jobs
15CMild Steel
3C
2R, 3R
Mild Steel
Standard Accessories
• 4 / 5 / 6 mm Hex. Socket Screw Key : each 1 pc. • Spanner 24 × 27 : 1 pc. • Hook spanner 25-28 : 1 pc. • 3 mm T Wrench Key : 1 pc. • TA9A093 Insert 12.7 Ass'y (12 pcs./set ) : 1 set
• Carbon Brush Ass'y : 1 pc.• 4 mm Hex. Wrench Key : 1 pc.• Insert 12.7 with hole : 1 pc.• Insert Set Screw 4 × 7 : 1 pc.• Hex Nut M8 : 2 pcs.• 8 × 25 mm Hex. Socket Set Screw : 2 pcs.• Spanner T-15D : 1 pc.
• 3 & 4 mm Hex. Socket Screw Key : each 1 pc.• Spanner T-9F : 1 pc.• Hex. Nut M8 : 2 pcs.• 8 × 25 mm Hex. Socket Set Screw : 2 pcs.
• Insert 12.7 with hole : 1 pc.• Insert set screw 4 × 7 : 1 pc.• 5 mm Hex. Socket Screw Key : 1 pc.• Spanner 8 × 10 : 1 pc.• Spanner T-15D : 1 pc.• Adjustment gauge : 1 pc.
SpecificationsModel (Electric Tool)
Power Source (Single Phase)
Rated Power Consumption W
Rated Current A
Rated Duty min
No-load Speed min-1 (rpm)
Chamfering Capacity
Chamfer Angle
Power Cord m
Mass (Weight) kg
HB-15B
Continuous
0C - 15C (7C per chamfering)
-
15˚ - 45˚
5
15
EMB-0307B
220 - 240 V AC, 50/60 Hz
1,010
4.6
Continuous
11,000
0C - 7C, 2R, 3R, 4R
0C - 3C, 2R, 3R, 4R
15˚ - 45˚
4
3.9
MB-03A
230 V or 115 V AC, 50/60 Hz
430
2 / 4.5
30
11,000
0C - 3C, 2R, 3R
-
45˚
2.5
2.5
ECB-0203
220 - 240 V AC, 50/60 Hz
450
2.1
30
11,000
0C - 3C, 2R, 3R
0C - 1.5C, 2R
45˚
2.5
2.5
115 V AC
910
10.5
3,340
230 V AC
910
4
2,750
Mild Steel
Stainless Steel
In case of chamfering 3R, an optional insert for 3R is necessary, and chamfering 2R, an optional guide sleeve 24 mm dia. and insert for 2R are necessary.
The limit of beveling width depends on a chamfer angle.
Chamfering range of operation CB-02 ECB-0203
Min. Diameter Min. Radius Min. Depth Min. Diameter Min. Radius Min. Depth Min. Thickness
Round
Radius
Chamfer Angle
Model
Material
Radius(mm)
Mild Steel (mm)
45˚30˚15˚
X1594
2, 3, 4 2, 3, 4 2, 3, 42, 3, 4 2, 3 2, 3 2 2
Y15
15.515.4
HB-15B
Mild Steel (mm)
Stainless Steel Stainless Steel Stainless SteelMild SteelMild Steel Mild Steel Mild Steel Mild Steel
X7
3.81.5
Y7
6.65.6
EMB-0307B
EMB-0307B
Stainless Steel (mm)
X3
2.21
Y3
3.83.8
Mild Steel (mm)
X3
Y3
MB-03A
MB-03A
Mild Steel (mm)
X3
Y3
Stainless Steel (mm)
X1.5
Y1.5
ECB-0203
ECB-0203
CB-02
CB-02
Mild Steel (mm)
X74
2.2
Y778
Mild Steel (mm)
X2
Y2
AMBL-0307 / AMB-0307
AMBL-0307 / AMB-0307
Stainless Steel (mm)
X3
2.21
Y3
3.83.8
Finish a surface so fine thatpost-sanding is unnecessary
Column R-section can be chamferedwith optional attachment
Insert with 4-side blades per piecepractices good economy
Applicable to stainless steel andmild steel chamfering
Pipe outer edge can be alsoprocessed with standard accessories
Dust box collects swarf and chipseffectively
EMB-0307B
3C 7C
4R4R
179 mm 316.4 mm
189.6 mm
Stainless Steel Mild Steel
An outer R-part attachment allowschamfering of outer diameters witha radius greater than 170 mm
An optional inner head ass’y allowschamfering a pipe of inner diameterlarger than 100 mm (50R)
Applicable to stainless steel andmild steel chamfering
Minimum chamfering plate thicknessis 2 mm (Max.0.5C)
An optional straight plate allowschamfering a straight edge shoulder
1.5C
2R
Stainless Steel 3C
3R
Mild Steel
295 mm
220 mm(Photo: 230 V AC Type )
150 mm 278 mm
107.5 mm400 mm
136.4 mm
Portable Chamfering ToolsBEVELER
15
XChamfer
YStraight
Select the suitable BEVELER model inaccordance with your applications
Applicable to stainless steel and mild steel chamfering
Simple to adjust chamfering depth and replace insert
Pipe outer edge can be also processed with standard accessories
180 mm
3C
7C
4R
Precisely adjust chamfer dimensions with accessory gauge
Versatility chamfer either inner or outer edges
2C
2R
136 mm
RingType
LeverType
Stainless Steel
Mild Steel
Mild Steel126 mm
202 mm
Optional
116 mm
180 mm
126 mm
177 mm
Standard Accessories• 3 & 4 mm Hex. Socket Screw Key : each 1 pc. • Spanner T-15F : 1 pc. • Hex Nut M8 : 2 pcs.
• 8 x 25 mm Hex. Socket Set Screw : 2 pcs.• Insert Set Screw 4 x 7 : 1 pc.
• Insert 9.525 with hole : 1 pc.• Adjustment gauge : 1 pc.• Spanner T-9F : 1 pc.
• Protective cap : 1 pc.• Hook Spanner 58-65 : 1 pc.
SpecificationsModel (Pneumatic Tool)
Air Pressure MPa (kgf/cm2)
Air Comsumption m3/min
No-load Speed min-1 (rpm)
Chamfering Capacity
Chamfer Angle
Mass (Weight) kg
AMBL-0307 / AMB-0307
0.59 (6)
0.9
14,000
0C - 7C, 2R, 3R, 4R
0C - 3C, 2R, 3R, 4R
15˚ - 45˚
2.9
CB-02
0.59 (6)
0.4
13,000
0C - 2C, 2R
-
45˚
1.8
Mild Steel
Stainless Steel
Portable Chamfering ToolsBEVELER
16
PN
TA9A093
TB01159
TB01791
TB01651
TB01790
TA9A386
TA9A592
TA9A638
TA9A728
TB02539
TA9A594
TB02857
TB03097
TB02862
TB03424
TQ01683
Indexable Insert 12.7 Ass'y
Indexable Insert 12.7 with hole Ass'y
Indexable Insert 12.7 Ass'y R2
Indexable Insert 12.7 Ass'y R3
Indexable Insert 12.7 Ass'y R4
Indexable Insert 9.525 with hole Ass'y
Indexable Insert 9.525 Ass'y R2
Indexable Insert 9.525 Ass'y R3
Plate Ass'y for pipe
Attachment for small dia. pipe
Inner head Ass'y
Guide sleeve 24 mm dia. Ass'y
Plate Ass'y for straight line use
Dust Box Ass'y
Spanner T-9D
Spanner T-15D
Sales Unit
12 pcs./set
10 pcs./set
10 pcs./set
10 pcs./set
10 pcs./set
10 pcs./set
10 pcs./set
10 pcs./set
1 set
1 set
1 set
1 set
1 set
1 set
1 pc.
1 pc.
Application model
HB-15B
EMB-0307B, AMB-0307, AMBL-0307, ECB-0203
EMB-0307B, AMB-0307, AMBL-0307, ECB-0203
EMB-0307B, AMB-0307, AMBL-0307, ECB-0203
EMB-0307B, AMB-0307, AMBL-0307
MB-03A, CB-02
MB-03A, CB-02
MB-03A
HB-15B
EMB-0307B, AMB-0307, AMBL-0307
MB-03A
ECB-0203
ECB-0203
ECB-0203
MB-03A, CB-02
EMB-0307B, AMB-0307, AMBL-0307, ECB-0203
Remarks
For pipe 125 - 800 mm dia.
For pipe 80 - 200 mm dia.
For min. 100 mm dia.
For chamfering R2
Used with Plate Ass'y for straight line use
Description
Model SH-100A
SUPER HANDFILING
Pneumatic & Electric Power Tools,Labor-saving plus Improved Work Efficiency
OTHER PRODUCT LINES
A wide range of unique tools for boring and punching
Model JT-20
JET CHISELNEEDLE SCALER
Model S-250/S-500/S-1000
SUPER KELENPNEUMATIC SCALER
Model JEX-2800A
JET CHISELNEEDLE SCALER
Model A-300
AUTO CHISELAIR HAMMER
Model B-10N
BELTONPNEUMATIC BELT SANDER
Model ADR-100
AIR DRILLPNEUMATIC HAND DRILL
Model B-20N
BELTONPNEUMATIC BELT SANDER
Model MLG-70
MYTONPNEUMATIC GRINDER
Model L-25B
AIR SONICPNEUMATIC DIE GRINDER
Model MAS-40
MYTONPNEUMATIC SANDER
Model APS-150
PALM ORBITAL SANDERPNEUMATIC COMPACT SANDER
Model ACH-16
AIR CHIPPERSCALING
Model MAGW-40
MYTONPNEUMATIC GRINDER
Model CH-24
AIR CHIPPERSCALING
Model MLG-25
MYTONPNEUMATIC GRINDER
Professional Tools for High Technology
DLV7300 SeriesDLV7500/8500 SeriesDLV7000/8000 SeriesDLV7100/7200/8100/8200 SeriesDLV3100/3300 SeriesDLV5720/5720H/5740/5740H/5750 SeriesDLV5800 SeriesDLV30SP/30HP-MKG (with built-in brushless motors)
Models
NITTO KOHKI "delvo" Electric Screwdrivers are high-quality tools for professional use,with special emphasis on precise control of torque and long life. They apply just thecorrect amount of torque –with sure, positive control always at your fingertips.They're smooth and shockless in operation, too. NITTO KOHKI's customer-orientedservice system is directly connected to sales agents to ensure thatyou can use "delvo" Electric Screwdrivers with confidence.
TW-00/TW-0/TW-3/TW-5/TW-9/TW-15/TW-22/TW-30/TW-40/TW-50/TW-60/TW-70
TIGON Spring Balancer ImprovesWork Safety & Efficiency
Models
MEDO pumps are unique products featuring a Linear-motor-driven Free Piston System.NITTO KOHKI has made available a complete series of air compressors and suction pumps that incorporate this revolutionary mechanism.These are quite appropriate as air sources or suction power units for various pneumatically operated equipmentand apparatus in advanced industries.
DLV5720/5720H/5740 Series
DLV30SP-MKG
DLV30HP-MKG
Capacities ranging from 0.5 - 70 kg.
17
Quick Connecting Fluid Couplings are The World'sBest for both Quality and Quantity
HI CUPLA &HI CUPLA 200• One-way shut-off coupling with an automatic shut-off valve in the socket.• Important pars are hardened for excellent wear resistance and durability.
PlugFor hose connection17PH20PH30PH
For 1/4" hoseFor 1/4" hoseFor 3/8" hose
10PM20PM30PM
20PF30PF40PF
For Rc 1/8"For Rc 1/4"For Rc 3/8"
For R 1/4"For R 3/8"For R 1/2"
20PFF For G 1/4"
40PH400PH600PH800PH
For 1/2" hoseFor 1/2" hoseFor 3/4" hoseFor 1" hose
17SH20SH30SH
For 1/4" hoseFor 1/4" hoseFor 3/8" hose
40SH400SH600SH800SH
For 1/2" hoseFor 1/2" hoseFor 3/4" hoseFor 1" hose
40PM400PM600PM800PM
400PF600PF800PF
For Rc 1/2"For Rc 1/2"For Rc 3/4"For Rc 1"
10SM20SM30SM
For Rc 1/8"For Rc 1/4"For Rc 3/8"
40SM400SM600SM800SM
For Rc 1/2"For Rc 1/2"For Rc 3/4"For Rc 1"
For R 1/2"For R 3/4"For R 1"
20SF30SF40SF
For R 1/4"For R 3/8"For R 1/2"
400SF600SF800SF
For R 1/2"For R 3/4"For R 1"
For hose connection
For female thread connection For female thread connection
For male thread connection For male thread connection
200-17SH200-20SH200-30SH
For 1/4" hoseFor 1/4" hoseFor 3/8" hose
200-40SH For 1/2" hose
200-20SM200-30SM200-40SM
For Rc 1/4"For Rc 3/8"For Rc 1/2"
200-20SF200-30SF200-40SF
For R 1/4"For R 3/8"For R 1/2"
For hose connection
For female thread connection
For male thread connection
For male thread connection (parallel thread)
SocketP S
TypeBody material SizeWorking pressurePressure resistanceSeal materialWorking temperature range
SpecificationsHi Cupla
Steel (chrome-plated)1/8", 1/4", 3/8", 1/2", 3/4", 1"
1.5 MPa2.0 MPa
NBR-20˚C - +80˚C
Hi Cupla 200 Steel (chrome-plated)
1/8", 1/4", 3/8", 1/2"1.0 MPa1.5 MPa
NBR-5˚C - +60˚C
Plug
S22PHS33PHS32PH*
For OxygenFor Fuel GasFor Fuel Gas
For 1/4" , 5/16"For 5/16" , 3/8"For 1/4" , 5/16"
PH type (Hose barb)
S225PHS335PH
For OxygenFor Fuel Gas
For 5 mm IDFor 5 mm ID
PH type (Hose barb of smaller diameters)
S22PNS33PN
For OxygenFor Fuel Gas
For 5 mm IDFor 5 mm ID
PN type (Nut type for small diameter hose)
S22PFS33PF
For OxygenFor Fuel Gas
For oxygen torch sideFox fuel gas torch side
PF type (Female thread for torch connection)
S23PFB-2*S33PFB-2*
For OxygenFor Fuel Gas
For oxygen torch sideFox fuel gas torch side
PFB type (Female thread with backflow stop valve)
S22SHS33SHS32SH*
For OxygenFor Fuel GasFor Fuel Gas
For 1/4" , 5/16"For 5/16" , 3/8"For 1/4" , 5/16"
SH type (Hose barb)
S225SHS335SH
For OxygenFor Fuel Gas
For 5 mm IDFor 5 mm ID
SH type (Hose barb of smaller diameters)
S22SNS33SN
For OxygenFor Fuel Gas
For 5 mm IDFor 5 mm ID
SN type (Nut type for small diameter hose)
S22SFS33SFS23SF*S33SF*
For OxygenFor Fuel GasFor OxygenFor Fuel Gas
For oxygen gauge sideFor fuel gas gauge sideFor oxygen gauge sideFor fuel gas gauge side
SF type (Female thread for torch connection)
S22SMS33SM
For OxygenFor Fuel Gas
For Rc 1/4For Rc 3/8
SM type (Male thread)
SocketP S
Body material SizeWorking pressurePressure resistanceSeal materialWorking temperature range
SpecificationsSocket : Brass (chrome-plated) Plug : Steel (chrome-plated)
1/4", 5/16", 3/8"0.7 MPa1.0 MPa
NBR-20˚C - +80˚C
Full line-up consisting of 3,000 series, 20,000 type variations. The couplings eliminate inconvenience of thread-in orbolted flange connections, fluid leakage, or hose kinking but provide speedy control and maintenance of fluid piping.
HI CUPLA ACE• Plastic Cuplas with a bult-in locking mechanism.• Pressure ratings comprable to steel Cuplas.
LINE CUPLA 200• Enables several air lines to be taken simultaneously from one supply line.• Gives speedy branching of Hi Cupla.
OTHER PRODUCT LINES
*Made-to-order item. • Available hose sizes are ø5 mm x ø11.2 mm, ø5 mm x ø11.5 mm and ø5 mm x ø11.8 mm.
Male thread For regulator For extension hose For torch
Select the combination in accordance with your own application.
Suggested combinationSM x PH
Suggested combinationSF x PH
Suggested combinationSH x PH
Suggested combinationSH x PF
For Oxygen / Fuel Gas
Heavy-duty push-to-connect typeor oxyacetylene piping
Mini Cupla Super
Exclusively for weldingand cutting equipment.• From cylinders to torches, all piping connections associated with welding and cutting equipment are now in push-to- connect configurations.• Chrome-plated body for better corrosion resistance.• Heat-treated plugs for better durability.• Oxygen and fuel gas couplings have different configuration sizes with sleeves in different appearances, chrome plating for oxygen and copper plating for fuel gas, to prevent accidental interconnection.• Smaller diameter design enables wider range of applications.• Various types of end configurations have been standardized to comply with a wide range of welding and cutting equipment applications. Interchangeable with Mini Cupla.
18
Overseas Affiliates/Offices
NITTO KOHKI U.S.A. INC.TEL:+1-630-924-9393 FAX:+1-630-924-0303
NITTO KOHKI EUROPE CO., LTD.(UK)TEL:+44-1923-239-668 FAX:+44-1923-248-815
NITTO KOHKI DEUTSCHLAND GMBHTEL:+49-7157-22436 FAX:+49-7157-22437
NITTO KOHKI AUSTRALIA PTY. LTD.TEL:+61-7-3340-4600 FAX:+61-73340-4640
NITTO KOHKI CO., LTD. SINGAPOREBRANCHTEL:+65-6227-5360 FAX:+65-6227-0192
NITTO KOHKI CO., LTD. BANGKOKREPRESENTATIVE OFFICETEL:+66-2-632-0307 FAX:+66-2-632-0308
NITTO KOHKI CO., LTD. SHANGHAIREPRESENTATIVE OFFICETEL:+86-21-6415-3935 FAX:+86-21-6472-6957
NITTO KOHKI CO., LTD. SHENZHENREPRESENTATIVE OFFICETEL:+86-755-8375-2185 FAX:+86-755-8375-2187
Printed in Japan 11LW07- 1
Specifications and designs are subject to change at any time without notice.
DISTRIBUTED BY
NITTO KOHKI CO.,LTD.
Head Office 9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo 146-8555 JapanPhone : +81-3-3755-1111 Fax : +81-3-3753-8791
URL : www.nitto-kohki.co.jp/eE-mail : [email protected]