Frigomeccanica S.p.A.Via Provinciale, 19 - 43038 SALA BAGANZA (Parma) Italy

Tel. +39 0521 835666 r.a. Fax +39 0521 834070E-mail: frigo@frigomeccanica.it www.frigomeccanica.it

This catalogue may be subject to technical variations

It is composed of a refrigerationsection and a heating section.These two sections can have ventilated or gravitycirculation. The refrigeration section may use directexpansion of gas or indirect expansion (glycoledwater).The maturing process is controlled in the variousphases by a programmable microprocessor whichensures the realization of cycles suitable to thecharacteristics of the product.

MATURING

TURBO / AIR DIFFUSERSThe system is suitable to dry products at a wide range of roomtemperatures.It is composed of an air treatment unit consisting of:- refrigeration section supplied by direct expansion of gas or

refrigerant;- heating section supplied by boiler water, recovery water from

condensing circuits or with hot gas;- ventilation section with high uniformity.Special care is given to the realization of uniform thermo-hygrometric conditions of the air by means of ejector cones, airdiffusers and left/right air damper to ensure optimal calibrationof drying times.The air renewal section can be equipped with enthalpy renewalwhich allows a significant reduction of energy costs when theexternal thermo-hygrometric conditions are favourable.A programmable microprocessor controller manages the variouscomponents of the system to achieve ideal drying cycles bydrawing moisture from the centre of the product in the shortestpossible time.

RESTING DRYING

SMOKING ROOM

This system is designed forthe smoking of products withcontrolled temperature andhumidity.It consists of a smokegenerator, an air treatmentunit and a set of ducts; allof the components arestainless steel, perfectlywashable and inspectable.

A) Exemple de dbut de cycle avec refoulement de lair depuis le bas et aspiration du haut, avec oscillation continue du flux dair

B) Exemple de dbut de cycle avec refoulement de lair depuis le haut et aspiration du bas, avec oscillation continue du flux dair

RESTING DRYING

BIFLUSSOThe BIFLUSSO system has been designed to meet the needsof the latest drying and cooking systems:- constant and uniform quality standard of treated products

even with high density;- reduced investment for new constructions with same

production capacity;- optimized air circulation with: ducting to ground and ceiling,

continuous laminar flow on discharge and suction, high-performing deflector profiles;

- compliance with sanitary and health regulations,as the room has only vertical, smooth and washablewalls.

RESTING DRYING

The BIFLUSSO system can, on request, be constructed invarious models.

BIFLUSSOFRIGOMECCANICA has designed and patented the new BIFLUSSOdrying system, which optimizes the circulation and the control of airflow within the room.This was made possible by special construction features of the structuraland system elements. These elements allow the air to circulate withalternating vertical movements from floor to ceiling and from ceilingto floor. At the same time airflow rate is regulated, in an oscillatingway, to obtain even horizontal distribution.

Maturing systems for cured meats

The system is composed of staticevaporators and hot-water heaters(boiler or heat recovery). The interaction between thesetwo systems determines the degree of drying and bloomingof both salt and product, consequently a different levelof penetration of the saline solution.The system is equipped with a microprocessor whichautomatically realizes run (drying) or pause (blooming)cycles, producing temperature variation curves suitablefor the type of product being processed: prosciutto,coppa, pancetta, speck, fiocchetto, etc.

The refrigeration system is basedon a series of static evaporators,which keep the room temperatureat the set value without removing high quantities of moisturefrom the product.

HIGH HUMIDITY SALTING

DRY SALTING

The system is composed of: cooling system based on direct

expansion of gas; heating system with hot water supplied by boiler, recovery

water from condensing circuits or hot gas (for ventilatedsystems).

The installation may be realized in several versions:Ventilated (generally for the first phase of pre-resting): Turbo, airdiffusers or BIFLUSSO.Gravity circulation (generally for the intermediate and finalphase).In this type of room the product is cold dried, room temperaturevaries between +1C and +5C and humidity is controlled toreach the desired drying.

RESTING