Schedule

Original EstimateN/W Construction of building for Flexible Electronics Center IIT Kanpur

SLNo Description Qty Unit

1 CARRIAGE OF MATERIALS

1.1

1.1.1 Earth Lead - 3 Km 4600 cum

1.2

1.2.1 Earth Lead - 1 m 1000 cum

2 EARTH WORK

2.1

2.1.1 All kinds of soil 900 cum

2.2

2.2.1 All kinds of soil. 1700 cum

2.3

2.3.1 All kinds of soil

2.3.1.1340 metre

2.4

2000 cum

2.5

2.5.1 All kinds of soil 536 cum

2.6

175 cum

2.7

2.7.1 All kinds of soil 2500 100 sqm

2.8

2.8.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 1500 litre

Carriage of Materials by mechanical transport including loading, unloading and stacking :

Carriage of materials by manual labour including loading, unloading and stacking for lead less than 0.5 Km :

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm diaFilling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.

Supplying chemical emulsion in sealed containers including delivery as specified.

2.9

1100 Sqm

2.1

400 Rm

3 CONCRETE WORK

3.1

3.1.1300 cum

3.2

3.2.120 cum

3.3

3.3.130 cum

3.4

233 sqm

3.5

75

3.6

233 sqm

3.7

30 sqm

4 REINFORCED CEMENT CONCRETE

4.1

4.1.1 Foundations, footings, bases of columns, etc. for mass concrete 525 sqm

Diluting and injecting chemical emulsion for pre-constructional anti termite treatment and creating a continuous chemical barrier under and alround the column pits, wall, trenches, basement excavation, top surface of plinth filling, junction of wall and floor ,along external perimeter of building , expansion joints , over the top surface of consolidated earth on which apron is to be laid surroundings of pipes and conduits etc. complete as per specifications ( plinth area of building at ground floor only shall be measured for payment.)With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Providing and fixing G.I sheet of 24 guage size 0.75 m x 3.00 m alround construction area with vertical ballies @ 2.5 m center to center and three number horizontal ballies of 75 mm to 100 mm dia. height upto 3.00 m including bracing of ballies at every 10 m. Removal of above material after due dismantling and taking back the material from the work site after completion of the work.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

per 50 kg cement

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for:

4.1.264 sqm

4.1.3 Suspended floors, roofs, landings, balconies and access platform 5500 sqm

4.1.4 Shelves (Cast in situ) 80 sqm

4.1.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers6000 sqm

4.1.6 Columns, Pillars, Piers, Abutments, Posts and Struts 4500 sqm

4.1.7 Stairs, (excluding landings) except spiral-staircases 365 sqm

4.1.8

194 sqm

4.1.9100 sqm

4.2

4.2.14500 sqm

4.3

4.3.1 Thermo-Mechanically Treated bars 85000 Kg

4.4

4.4.1 Thermo-Mechanically Treated bars 400000 Kg

4.5275 metre

4.6

4.6.1 All works upto plinth level 200 cum

4.6.2 All works above plinth level upto floor V level 300 cum

4.7

4.7.1

500 cum

4.7.2

500 cum

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the likeExtra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum.Excess/ less cement used as per design mix is payable/recoverable separately).

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately.

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing M-35 grade concrete instead of M-25 grade BMC/ RMC. (Note : Cement content considered in M-35 is @ 350 kg/ cum)

4.8

4.8.1 All works upto plinth level 600 cum

4.8.2 All works above plinth level upto floor V level 1850 cum

4.9500 cum

4.1

4.10.1 200 mm wide. 682 metre

4.11

1250 Sqm

4.12

682 Mt

4.13

31 Sqm

5 BRICK WORK

5.1

5.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 100 cum

5.2

5.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 905 cum

5.3

5.3.1 cement mortar 1:4 (1 cement : 4 coarse sand) 100 sqm

5.4

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete,improve workability without impairing strength and durability as per direction of the Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/recoverable separately).

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.

Providing and fixing precast cement concrete slabs in CC 1:2:4 with nominal reinforcement 60mm thick including fixing by means of clamps all complete as per drawings and as directed by the Architect

Providing & laying Silicon sealent (GE, DOW CORNING or equivalent) to expansion joint including providing & fixing backer rod & masking tape as per the manufacturer's specifications or as directed by the Engineer-in-charge complete (upto 50 mm wide & 12 mm deep)."Providing and fixing in expansion joint Expanded polyethylene of density 28 to 32 kg/cum like Armour board or Equivalent approved make of desired thickness ( required thickness to be made up at source using minimum 10 mm thick sheet ) using adhesive or double sided adhesive tape to the casted surface to form the expansion joint of required width.This item shall included preparation of surfaces by cleaning of dust , oil, loose aggregate etc. Expansion joint 50 mm Thick."

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

5.4.1 Cement mortar 1:4 (1 cement :4 coarse sand) 1904 sqm

5.5500 sqm

5.61954 sqm

5.7

375 metre

Sub-Total

6 MARBLE WORK

6.1

6.1.1

6.1.1.1 Area of slab over 0.50 sqm 2924 sqm

6.2

6.2.1


6.2.2 Granite of any colour and shade

6.2.2.1 Area of slab upto 0.50 sqm 25 sqm


6.3

6.3.1 Marble work 100 metre

6.3.2 Granite work 38 metre

6.4

38 metre

6.5

29 each

6.62700 sqm

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately).

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

6.7

6.7.1 Stainless steel cramps 1754 kg

6.8

6.8.1 Granite Stone of approved shade 12 sqm

6.9

4027 sqm

Sub-Total

7 WOOD AND P.V.C. WORK

7.1

7.1.1 Second class teak wood 3 cum

7.2

7.2.1298 sqm

7.3

298 sqm

7.4

7.4.1 Rectangular or square 298 sqm

7.5298 sqm

7.6

7.6.1 50 mm long 1578 each

Providing and fixing cramps of required size & shape in RCC/ CC / Brick masonry backing with cement mortar 1:2 ( 1 cement :2 coarse sand), including drilling necessary hole in stones and embedding the cramp in the hole (fastener to be paid separately).

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :a. Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsExtra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.

7.7

152 each

7.8

152 each

7.9

7.9.1300 sqm

7.1

7.10.1 1.0 mm thick 595 sqm

7.11

63 metre

7.12

36 sqm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS: 2095: part IProviding & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

7.13

10 each

7.14

152 Each

7.15

304 Pair

7.16

7.16.198 Each

7.16.254 Each

7.17

7.17.1196 Each

7.17.2 108 Each

Sub-Total

8 STEEL WORK

8.1

12740 kg

8.2

8.2.1 Using M.S. angels 40x40x6 mm for diagonal braces 35 sqm

8.3

8.3.1 80x1.20 mm M.S. laths with 1.20 mm thick top cover 19 sqm

8.4 Providing and fixing ball bearing for rolling shutters. 4 each

8.5

8.5.12000 kg

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

P/F Satin stainless steel grade 316 door stopper including the cost of screw and other incidental charges complete all as per design approved by Engineer- in- Charge.

Providing and fixing satin stainless steel grade 316 pull handle including the cost of screw and other incidental charges complete.200mm all as per design approved by Engineer- In- Charge

Providng and fixing Stainless steel tower bolt including the cost of screws etc. complete all as per design approved by Engineer-in-charge.

250 x 10 mm.

150 x 10 mm.

Providing and fixing of stainless steel grade 304 sliding door bolt satin S.S. finish including the cost of screws and other incidental charges as per the design approved by Engineer- In -charge.

250 x 16 mm.

300 x 16 mm.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

8.6

8.6.1 M.S. tube 300 kg

8.7

8.7.1 10 x 120 mm 100 each

8.8

2500 kg

Sub-Total

9 FLOORING

9.1

9.1.1 40 mm thick with 20 mm nominal size stone aggregate 1345 sqm

9.2

9.2.1 18 mm thick 135 sqm

9.3

9.3.1 40 mm wide and 4 mm thick 1700 metre

9.4 Extra for pre finished nosing to treads of steps of marble stone. 454 metre

9.5150 sqm

9.6

9.6.1 25 mm thick 2600 sqm

9.7

60 sqm

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors.

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

9.8

9.8.1 Red sand stone 300 sqm

9.9252 metre

9.1

450 sqm

9.11

400 sqm

9.12

9.12.1 Size of Tile 600x600 mm 500 sqm


9.13

600 sqm

9.14


9.15

60 Sqm

40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Granite stone slabs 18 mm thick in risers of skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

9.16

1361 Rmt.

9.17

300 Sqm

9.18

784 Sqm

Sub-Total

10 ROOFING

10.1

10.1.1 In 75x75 mm deep chase 372 metre

10.2

12 each

10.3

10.3.1 75 mm diameter 30 metre


10.4

10.4.1 Coupler

10.4.1. 110 mm 24 each

10.4.2 Single pushfit Coupler

10.4.2. 75 mm 6 each

10.4.2. 110 mm 12 each

10.4.3 Single tee without door

10.4.3. 110x110x110 mm 12 each

10.4.4 Bend 87.5°

10.4.4. 75 mm bend 4 each

10.4.4. 110 mm bend 12 each

10.5

10.5.1 110 mm 262 each

Extra for providing antiskid grooves of size 6mm x 6mm (3nos.) on tread of riser as per detail drawing and directed by Engineer-In-charge.

Providing and laying 70mm thick factory made reinfonced cement concrete grass paver block (9600x4000) of approved shape and of approved make (concrete Product or equivalent) over 40mm sand mixed with earth laid to required gradient and finishing & cleaning of surface etc. all complete.

Providing and fixing Terracotta tiles on terrace in cement mortar 1:4 all complete as per drawings and as directed by the Architect

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

10.6

12 each

10.7

10.7.1765 sqm

10.8

135 sqm

10.9

1058 sqm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part IProviding and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/ cosmos / Hexa or equivalent of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone /Cosmos/ hexa) in the grid, including, cutting/ making openingfor services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge.

Providingand fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building.

10.1

2294 Sqm

10.11

300 Sqm

10.12

100 Sqm

Sub-Total

11 FINISHING

11.1 12 mm cement plaster of mix :

11.1.1 1:6 (1 cement: 6 coarse sand) 9000 sqm

Providing and fixing in position 600x600x15mm Gedina A glasswool ceiling tile of Ecophon make with 15mm grid system. The tiles should have humidity resistance of 95% rh, NRC 90% (acoustic erformance) colour white, fire performance class0/class1 (BS-476) in module 00x600x15 mm with tissue backing, with 15 mm wide hot dipped galvanised steel T section suspension system as per architects approval at required spacing, finishing of all joints, cuts made in the tiles to be neatly sealed by white cement leaving no exposed glass wool and made to proper line & level including providing of dditional framework for electricals fixtures. Diffusers cutouts for fire sprinklers etc. as per the specifications approved by architects Including necessary scaffolding supports, suspenders etc. The installation to comprise of main runners spaced at 1200mm centres securely fixed to the structural soffit by approved hangers at 1200 mm maximum centres and not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600 mm from the adjacent wall. 1200 mm long cross tees to be interlocked between main runners at 600mm centres to form 1200x 600 mm modules. Cross tees longer than 600 mm require ependent support. 600x600 mm modules to be formed by fitting 600 mm long cross tees centrally between the 1200 mm cross tees. The 1200 mm cross tees to have central “birdsmouth “ notches to facilitate fitting of 600 mm cross tees.(The work to include cost in all levels including scaffolding)

Providing and fixing 80 x 12 and 40x12 mm thick steambeech wood slats with a groove of 15mm between slats in pattern as per Architect on the framework with steel screws, comprising 40x40x18G M.S.tubular frame 900x340mm c/c (max.) supported away and fixed to wall surface by 40x40x5 mm thick MS angle supports/cleats of suitable size fixed with expansion fasteners etc. The framework to have welded connections (Min. 20mm fillet weld on each face) including two or more coat of apporved steel primer. The slat to be backed with black dyed jute fabric, 28GX10 G. I. wire mesh and to be backed with 50 mm thick resin bonded glass wool (24 kg/cum) cut to size and inserted in framework and held in place with 28G X 12 mm G. I. wire netting. Entire work to be done as per drawing, specifications and direction of Engineer-in-charge. The slats to be wax polished after wood filler and sand papering upto smooth finish in natural colour. """

Providing and fixing 4mm thick steambeech veneered ply (Kitply,Greenply,Century or equivalent) on 6mm thick water proof marine ply, bonded with phenolic (Kitply,Greenply,Century or equivalent) and the surface finished with moulded steambeech beading of 15 x 25mm in pattern as per drawing or as directed by Architect , with 38mm long self tapping and self drilling steel screws on framework comprising 40x40x18G M.S. tubular frame 600x600mm c/c (max.), fixed to wall surface by 40x40x5 mm thick MS angle supports/cleats of suitable size fixed with expansion fasteners etc. The framework to have welded connections (Min. 20mm fillet weld on each face) including two or more coat of apporved steel primer. Ply to be backed by 50mm thick glass wool (24kg/cum) cut to size and inserted in framework and held in place with 28G x 12mm GI wire netting. Entire work to be done as per drawing, specifications and direction of Engineer-in-charge. To be wax polished in natural colour.

"

11.2

11.2.1 1:6 (1 cement: 6 coarse sand) 3000 sqm

11.3

11.3.1 1:3 (1 cement: 3 fine sand) 400 sqm

11.4 6 mm cement plaster of mix :

11.4.1 1:3 (1 cement : 3 fine sand) 10000 sqm

11.5

2000 sqm

11.6 White washing with lime to give an even shade :

11.6.1 New work (three or more coats) 3000 sqm

11.7

11.7.1 Two or more coats on new work 4000 sqm

11.8 Finishing walls with textured exterior paint of required shade :

11.8.1

1000 sqm

11.9


11.1


11.11

9200 sqm

11.12

1665 Sqm

11.13

11 Sqm

12 DISMANTLING & DEMOLISHING

12.1

12.1.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 10 cum

12.2

12.2.1 In cement mortar 10 cum

15 mm cement plaster on rough side of single or half brick wall of mix:

12 mm cement plaster finished with a floating coat of neat cement of mix :

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing 24 gauge Chicken Wire mesh in junction of block work & RCC works at corner/wall surface as per direction of Engineer-In-Charge.

Providing and fixing 6mm thick frame less bevelled (25 to 40mm) edge mirror of all shapes and sizes with 12mm thick marine ply (conforming to IS 710) backing fixed to wall with approved fastener including providing and fixing 300 micron HDPE film as vapour barrier & polyyethylene bubble sheet between mirror and backing ply including all necessary fixing arrangement like nails/ screws dash fastener, wood preservative paint, 1" stainless steel studs (at four corners) etc. complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

12.3

12.3.1 bituminous road 250 sqm

12.4

60 cum

13 ROAD WORK

13.1

300 sqm

13.2

13.2.1 Cement concrete prepared with batch mixing machine 38 cum

13.3

4 cum

Sub-Total

14 SANITARY INSTALLATIONS

14.1

14.1.11 each

Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

14.2

14.2.1 W.C. pan with ISI marked white solid plastic seat and lid 1 each

14.3

14.3.113 each

14.4

14.4.11 each

14.5

14.5.1 Kitchen sink with drain board

14.5.1. 510x1040 mm bowl depth 250 mm 2 each

14.6

14.6.1 Size 600x450x200 mm 9 each

14.7

14.7.1 Flexible pipe

14.7.1. 32 mm dia 9 each

14.7.1. 40 mm dia 2 each

14.8 Providing and fixing toilet paper holder :

14.8.1 C.P. brass 23 each

14.9 Providing and fixing soil, waste and vent pipes :

14.9.1 100 mm dia

14.9.1.500 metre

14.1

14.10.1 For 100 mm dia pipe 218 each

14.11

14.11.1 100 mm dia

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Range of three half stall urinals with 10 litre P.V.C. automatic flushing cisternProviding and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tapProviding and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

14.11.1 Sand cast iron S&S as per IS - 3989 55 each

14.12 Providing and fixing plain bend of required degree.

14.12.1 100 mm dia

14.12.1 Sand cast iron S&S as per IS : 3989 6 each

14.13 Providing and fixing heel rest sanitary bend

14.13.1 100 mm dia


14.14

14.14.1 100x100x100 mm


14.15 Providing and fixing single equal plain junction of required degree :

14.15.1 100x100x100 mm


14.16 Providing and fixing terminal guard :

14.16.1 100 mm


14.17 Providing and fixing collar :

14.17.1 100 mm


14.18

14.18.1 100 mm 400 each

14.19

14.19.1 100 mm 10 each

14.2

14.20.1 100 mm inlet and 100 mm outlet

14.20.1 Sand cast iron S&S as per IS: 3989 36 each

14.21

14.21.1 100 mm dia 42 metre

14.22

14.22.1 100 mm diameter pipe 300 metre

14.23 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

14.23.1

32 each

14.24

11 each

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for ew work :

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

14.25

22 each

14.26

13 Each

15 WATER SUPPLY

15.1

15.1.1 15 mm nominal outer dia Pipes 10 metre




15.2

15.2.1 20 mm dia nominal bore 15 metre





15.3



15.4



15.5

15.5.1 50 to 80 mm nominal bore 2 each

15.6

15.6.1 25 mm nominal bore 12 each

15.6.2 32 mm nominal bore. 1 each



Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Supplying and installation of flush valve jaguar metropole make of urinal i/c testing etc. complete.

40 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

15.7


15.8

15.8.1 45 cm length

15.8.1. 15 mm nominal bore 50 each

15.9






15.1





15.11



15.12






15.13

20000 per litre

15.14


15.15


15.16


15.17


Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

Providing and fixing uplasticised PVC connection pipe with brass unions :

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISi : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15.18

15.18.1 15mm nominal bore 50 each

15.19 Providing and fixing PTMT grating of approved quality and colour.

15.19.1 Circular type

15.19.1 125 mm nominal dia with 25 mm waste hole 51 each

15.2

23 Each

15.2124 Each

15.22

23 Each

15.23

2 Each

15.24

23 Each

15.25

10 Each

15.26

10 Each

15.27

10 Each

15.28

2 Each

15.29

1 Each

15.3

5 Each

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

P/Fixing C.P. Health faucet made from superior Engineering Plastic (POM) from Dupont, spray and reinforced pvc tube should be capable of having burst presure of 15 bar and working pressure of 10 bar (Make Hindware - F160002)

Providing & fixing CP brass Robe hook complete in all respects. (Make Hindware Contessa F880004)

Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector. (Make MacAlpine Model No MAC 1)

Providing and Fixing deck wall mounted sink mixer with Swivel Casted spout complete, including cutting and making good the walls wherever required. (Make Hindware Cat No F100023)

Providing and fixing CP brass 2 WAY bibcock of approved quality conferming to IS standards (Make Hindware Cat No F100004)

Providing & Fixing hand drier of best quality, to be operated with 230 volts, single phase, with fully hygienic condition, with all accessories including cutting and making good the walls, wherever required. (Make Euronics Cat No EH05M)

Providing & Fixing Aerosole Perfume Dispenser (Digital programming) fixed to wooden cleats with C.P brass screws, complete including cutting and making good the walls wherever required. (Make Euronics Cat No EA03)

Providing & Fixing ABS/Plastic body paper towel dispenser Capacity 450-500Paper Towels)complete with brackets fixed to wall with PVC rawl plug with CP brass screws complete in all respects, including cutting and making good the wall wherever required. (make Euronics Cat No EP03)

Providing & Fixing SS Grab Bar size 450mm/25MM in handicape toilet area complete as required. (Make Euronics - Cat No EGR01)

Providing and fixing CP Self closing Eye wash Fountain (Make Vijay Cat No :- 1036)

Providing & Fixing Steenless Steel Water Cooler Cap 40 Ltrs/Hr. Installed along with RO system complete with all respect.

15.31

9 Each

15.32

18 Each

15.33

1 Each

15.34

18 Each

Sub-Total

16 DRAINAGE

16.1



16.2

16.2.1 150 mm diameter S.W. pipe 65 metre



16.3

16.3.1 150 x 100 mm size P type16.3.1.

8 each

16.4

16.4.1 250 mm dia. R.C.C. pipe 155 metre

Providing & Fixing ABS body 1000 Mililiter liquid soap dispenser with simple push lever fitted with liquid soap (one time) including cutting and making good the walls, wherever required.(Make Euronics Cat No - ES06A)

Providing & fixing CP brass Pillar Cock Self Closing System for wash basin with pop up waste complete including cutting and making good the walls where required.(Make Hindware Cat No F310001)

Providing and Fixing Central Hole Basin Mixture Without Popup Waste System with 450mm Long Flexible Hose), including cutting and making good the walls wherever required. (Make Hindware Cat No F100014)

Providing and fixing Oval wash basin with CI brackets, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls where ever require.White Vitreous China Wash basin size 560x450 mm . (Make Hindware ZEN Cat No 2040) &( Waste Coupling Cat No F850001)

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

16.5

16.5.1

16.5.1.15 each

16.5.2

16.5.2.2 each

16.6 Extra for depth for manholes :

16.6.1 Size 120x90 cm

16.6.1.1 metre

16.7

16.7.114 each

16.8

1 Set

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5Providing and fixing Vertical/horizontal monoblock centrifugal transfer pumping set with SS body and SS impeller, SS shaft mechanical seal, connected to a TEFC induction motor suitable for 415 volts ± 3% phase 50 cycles AC supply with a common suction header of 100 mm dia with valves on main connecting & pumps inlet and a common delivery header with valves, includingt water shock absorber, non return valves with MS galvanized supports and painting with one coat of primer and two coats of synthetic enamel paint including a 100mm dia pressure gauge, C.I. Y type suction strainer Vibration eliminating pads under foundation, all mounted on a common base plate of MS 80x40mm I section bolted to RCC foundation complete in all respects.Domestic Water Transfer pump set(1 working + 1 stand by) Capacity - 50 lpm (Each)Head - 50m

16.9

1 Set

Sub-Total

17 ALUMINIUM WORK

17.1

17.1.1 For fixed portion

17.1.1.

9600 kg

17.1.2

17.1.2.

2865 kg

17.2

17.2.1 With float glass panes of 5.50 mm thickness 228 sqm

17.3

17.3.1 Upto 5mm depth and 5 mm width 717 metre

Drainage Sump PumpsSubmersible pumps for basement drainage & Pump Room drainage.Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect(one working + one standby/both working in high flow conditions (Solid handiling capacity 12mm)Capacity- 100 lpm (Each)Head - 10 m

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

17.4

490 sqm

17.5

17.5.1 355 X 19 mm 100 each

17.6

17.6.1 Anodized (AC 15) aluminium 556 each

17.7

80 sqm

17.8

40 Each

17.9

80 Each

17.1

523 Sqm

Sub-Total

18 WATER PROOFING

18.1

250 sqm

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing Ozone or equivalent floor spring and patch fittings for glass door including all hardware all complete as per drawings and as directed by the Architect

Providing and fixing Ozone or equivalent Handles for glass door including all hardware all complete as per drawings and as directed by the Architect

Providing and fixing 10mm thick clear toughned glass in glazing partitions with Aluminium U clips as per manufacturers recommendations including all hardware all complete as per drawings and as directed by the Architect

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

18.2

18.2.11058 sqm

18.3

15 Cum

Sub-Total

19 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL

19.1

1108 sqm

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.Providing and filling light weight (Density 500 kg / Sqm) Foam concrete in sunken areas of toilet and WC as directed by the Architect

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and

19.2

574 sqm

Sub-Total

20 MINOR CIVIL MAINTENANCE WORK

20.1

13 Each

20.2

300 sqm

20.3

682 Meter

20.4

31 Sqm

Design supply & installation of suspended Spider Glozing system designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the

Supplying and installation of flush valve jaguar metropole make of urinal i/c testing etc. complete.

40 mm nominal bore

Providing and laying 70mm thick factory made reinfonced cement concrete grass paver block (9600x4000) of approved shape and of approved make (concrete Product or equivalent) over 40mm sand mixed with earth laid to required gradient and finishing & cleaning of surface etc. all complete.

"Providing & laying Silicon sealent (GE, DOW CORNING or equivalent) to expansion joint including providing & fixing backer rod & masking tape as per the manufacturer's specifications or as directed by the Engineer-in-charge complete (upto 50 mm wide & 12 mm deep)."

"Providing and fixing in expansion joint Expanded polyethylene of density 28 to 32 kg/cum like Armour board or Equivalent approved make of desired thickness ( required thickness to be made up at source using minimum 10 mm thick sheet ) using adhesive or double sided adhesive tape to the casted surface to form the expansion joint of required width.This item shall included preparation of surfaces by cleaning of dust , oil, loose aggregate etc. Expansion joint 50 mm Thick."

20.5

300 Sqm

20.6

100 Sqm

Sub-Total

21 FIRE HYDRANT SYSTEM

21.1

2 Each

"Providing and fixing 80 x 12 and 40x12 mm thick steambeech wood slats with a groove of 15mm between slats in pattern as per Architect on the framework with steel screws, comprising 40x40x18G M.S.tubular frame 900x340mm c/c (max.) supported away and fixed to wall surface by 40x40x5 mm thick MS angle supports/cleats of suitable size fixed with expansion fasteners etc. The framework to have welded connections (Min. 20mm fillet weld on each face) including two or more coat of apporved steel primer. The slat to be backed with black dyed jute fabric, 28GX10 G. I. wire mesh and to be backed with 50 mm thick resin bonded glass wool (24 kg/cum) cut to size and inserted in framework and held in place with 28G X 12 mm G. I. wire netting. Entire work to be done as per drawing, specifications and direction of Engineer-in-charge. The slats to be wax polished after wood filler and sand papering upto smooth finish in natural colour. "

"Providing and fixing 4mm thick steambeech veneered ply (Kitply,Greenply,Century or equivalent) on 6mm thick water proof marine ply, bonded with phenolic (Kitply,Greenply,Century or equivalent) and the surface finished with moulded steambeech beading of 15 x 25mm in pattern as per drawing or as directed by Architect , with 38mm long self tapping and self drilling steel screws on framework comprising 40x40x18G M.S. tubular frame 600x600mm c/c (max.), fixed to wall surface by 40x40x5 mm thick MS angle supports/cleats of suitable size fixed with expansion fasteners etc. The framework to have welded connections (Min. 20mm fillet weld on each face) including two or more coat of apporved steel primer. Ply to be backed by 50mm thick glass wool (24kg/cum) cut to size and inserted in framework and held in place with 28G x 12mm GI wire netting. Entire work to be done as per drawing, specifications and direction of Engineer-in-charge. To be wax polished in natural colour. "

Electrical Fire Hydrant and Sprinkler PumpsProviding and fixing horizontal centrifugal end suction single/multi stage, single/multi outlet pumping set with bronze impeller with C.I. body and connected by a flexible coupling to a totally enclosed fan cooled induction motor mounted on a common structural base plates with all pump accessories complete as per specifications including pressure gauges with gunmetal isolation valves and anti vibration pad, motor to be suitable for 415 volts, 3 phase, 50 cycles A.C. supply (Specifications as per fire fighting requirements and on the pattern of TAC or local authority approval) as per instruction and following specifications: (All pumps shall have mechanical seal)Type : End SuctionSpeed (rpm) : 2900Capacity : 2280 lpmHead : 75 Mtr.App. H.P. : 60

21.2

1 Each

21.3

1 Each

21.4

1 Each

21.5

15 Rm

Providing and fixing horizontal centrifugal end suction single/multi tage, single/multi outlet pumping set with bronze impeller with C.I. body and connected by a flexible coupling to a totally enclosed fan cooled induction motor mounted on a common structural base plates with all pump accessories complete as per specifications ncluding pressure gauges with gunmetal isolation valves and anti vibration pad, motor to be suitable for 415 volts, 3 phase, 50 cycles A.C. supply (Specifications as per fire fighting requirements and on the pattern of TAC or local authority approval) as per instruction and following specifications: (All pumps shall have mechanical seal)Fire Jockey PumpType : End SuctionSpeed (rpm) : 2900Capacity : 180 lpmHead : 75 Mtr.App. H.P. : 12.5

Diesel Fire PumpProviding and fixing Centrifugal end suction single/multi stage, single/multi outlet pumping set with C.I.body and bronze impeller connected by means of a flexible coupling to a water cooled diesel engine mounted on a common structural base plate with anti-vibration pads and foundation complete with electric panel, 24v battery (including one spare battery), exhaust pipe of required length to discharge outside building with muffler, day oil tank mounted on suitable structural supports complete in all respects as per specifications ready for use and as per latest requirement of fire authority regularities.(All pumps shall have mechanical seal)Type : End SuctionSpeed (rpm) : 1800Capacity : 2280 lpmHead : 75 Mtr.App. H.P. : 62

Air Vessel for Fire PumpProviding and fixing double flanged vertical air vessel fabricated from 10mm M.S. plate with dished ends from 10mm M.S. plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality of pressure switches, pressure gauge and all other required accessories to operate commonly main fire pump, sprinkler pump and Jockey pump at drop of pressure, automatically at required pressure setting;Recommended dia. : 450mmHeight of shell : 2000mmWorking pressure : 7 Kg/Sq.cm Test Pressure : 10 Kg/Sq.cm

Providing & fixing MS Class ‘C’ diesel engine exhaust pipe (including all fittings, clamps, steel support) 150mm for the engine. The pipe shall be provided with 12 mm thick supercera ceramic fibre rope.

21.6

3 Each

21.7

3 Each

21.8

1 Each

21.9

21.9.115 Rm

21.9.230 Rm

21.1

30 Rm

21.11

15 Rm

21.12

21.12.110 Rm

providing & fixing standard type pressure switches to operate /stop fire pumps as per requirement with complete required accessories .

Providing and fixing Pressure gauge with isolation cock suitable with ‘U’ tube for maximum pressure of 7 Kg/cm2. (0-16 Kg./cm2; dial size:100 mm dia.)

Panel- for Fire Pumps

Design, manufacture, supplying, fixing in position, testing and commissioning of the following front operated cubicle type, front access 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42 protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system and suitable for a fault level of 25 MVA symmetrical at 415 volts with a suitable power capacitor to improve power factor.All switchboards shall have provision for entry of cables from the top or bottom as required.All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all outgoing feeders doors and switch handles shall be locakble in OFF position.

INCOMING

1 No. 630 amps TPN switch fuse unit with HRC fuses complete.

1 No. square flush mounting 0-500 volts scaled voltmeter with selector switch & control MCB'S

Three phase indicating lights with 2A SP Control MCB's.

BUSBAR

Electrolytic high conductivity three phase and neutral bus bar rated at 800 amps having a current density of 1 amp per Sqmm suitable to with stand symmetrical fault level of 25 MVA at 415 volts.

OUTGOING UNITS

2 Nos. 400 amps TPN MCCB (25KA) c curve with rotary handle

1 No 63amps TPN MCCB 25KA "C" Curve with rotary handle.

1 Nos. fully automatic Star-delta starters suitable for main pump motors with OLR, SPP, timer, Push button, Auto, manual slector switch, ON OFF lamp etc. complete.

1 No. fully automatic DOL Strarter for jockey pump with OLR, SPP, timer, Push button, Auto, manual slector switch, ON OFF lamp etc. complete.

2 Nos panel type ameter for each pump with CTS ASS etc.

Phase Indicating lamps with each starter

All inter connecting busbar/power cable control cable etc inside panel shall be fully automatic DE starting panel complete with battary charger, Hooter, Anunciator window, transformer, Rectifier, Ameter, Volt meter, push butten, Relay etc complete as required.

The motor control panel shall be prewired with colour coded wires with identification labels complete in all respects as required.

Providing and fixing heavy duty copper control control cables 1.1 KVA grade including necessary support clamps at ceiling level and connection legs complete in all respects.

Power cable 3..5 core 16 Sq.mm

Power cable 3.5 core 90 Sq.mm

Providing & Fixing G.I. earthing wire 8 gauge from all motor and M.C.C panel to be connected in as approved manner to the general earthing system complete.

Providing and fixing GI Earthing strip of Size 25 x 6mm for higher size motors and MCC panels to be connected in as approved manner to the general earthing system complete.

Providing and fixing Perforated type GI cable tray supported from ceiling at intervals of 60cms on both ends including cable clips with nuts and bolts welding of support rods with ceiling inserts or through dash fasteners cutting and making good complete.

300mm wide X 40 X 40mm and 2mm thick

21.12.210 Rm

21.13

21.13.11 Each

21.13.22 Each

21.13.31 Each

21.14

21.14.11 Each

21.14.22 Each

21.14.31 Each

21.15

21.15.11 Each

21.15.24 Each

21.15.31 Each

21.16

21.16.11 Each

21.16.22 Each

21.16.31 Each

21.17

2 Each

21.18

1 Each

150mm wide X 40 X 40mm and 2mm thick

Providing and fixing rubber expansion joints PN-16(to provide relief from stresses at pipe flanges) as per specification of the manufacturers.

200mm dia

150mm dia

80mm dia

Providing and fixing C.I double flanges suction strainer “Y” type including, nuts, bolts and 3mm thick rubber insertion complete.

200mm dia

150mm dia

50mm dia

Providing and fixing doubble flanged butterfly valves, wafer end type class PN 1.6 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box)

200mm dia

150mm dia

80mm dia

Providing and fixing C.I double flanged horizontal/vertical type non-return valve including nuts, bolts, 3mm thick rubber insertions complete to I.S:5312, Part-I, swing type, class PN 1.6.

200mm dia

150mm dia

80mm dia

Providing and fixing gun metal two-way fire brigade inlet connection consisting of 63mm instantaneously male coupling and a check valve protected by cap scored with a chain glass bore etc. complete with one 150mm dia sluice valve and 150mm dia non-return valve (To be connected to GF riser / External Ring)

Providing and fixing gun-metal 4-way fire brigade inlet connection of 4 nos. 63mm dia instantaneous type male coupling with built in check valves and 150mm dia flanged outlet complete with bolts, nuts and rubber insertions as per I.S:904. (to be connected to static tank).

21.19

1 Each

21.2

21.20.1217 Rm

21.20.25 Rm

21.21

21.21.1148 Rm

21.21.27 Rm

21.21.314 Rm

21.22

14 Each

21.23

14 Each

21.24

14 Each

21.25

14 Each

Providing and fixing gun metal fire brigade suction (draw out connection) with female coupling as per I.S:902-1974 complete and with 150mm dia. suction pipe and foot valve (To be connected to static tank)

HYDRANT SYSTEM

Providing, laying, jointing and testing of Mild Steel black pipe (IS: 1239/IS: 3895) heavy class including cutting, screwing, welding etc. complete with fitting viz. tees elbow, bends, flanges, reducers. etc including excavation in all kind of soil , refilling , ramming,shoring, removing the excavated surplus material , providing adequate support to the pipe and making good the same. Providing anti-corrosive treatment (coating and wrapping) with 4 mm thick tape and holiday test check as per IS: 10221 complete as required. Note : Pipes upto and 50 mm dia shall be threaded joints, above 50mm shall be welded joints.

150mm dia

80 mm dia

Providing and fixing MS black pipes as per IS 1239 (Part I) HEAVY Class including cutting, welding etc. complete with fittings viz Tees, Elbows, Bends, flanges, reducer, clamps, hanger etc. including painting with one coat of primer and two coat of synthetic enamel paint of approved make and shade

150 mm dia.

80 mm dia.

25 mm dia.

Providing, fixing, testing and commissioning of First-Aid-fire Hose reel wall mounting swinging type complete with drum, bracket, stop valve and 20mm dia. 30M long high pressure dunlop hose reel tubing with gunmetal shutoff nozzle conforming to IS: 8090 - 1976 with 5mm orifice. The hose reel shall be as per IS:884-1985.

Providing and fixing brass ball with wheel tested to 20 Kg/cm2 (I.S:778-1971, Class - II) of approved quality for hose reel

Providing and fixing Pressure gauge with isolation cock suitable with ‘U’ tube for maximum pressure of 7 Kg/cm2. (0-14 Kg./cm2; dial size:100 mm dia.)

Providing and fixing butterfly valves, wafer end type class PN 1.6 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box) 80mm dia

21.26

19 Each

21.27

19 Each

21.28

38 Each

21.29

5 Each

21.3

14 Each

21.3114 Each

21.32

2 Each

21.33

21.33.1107 Rm

21.33.243 Rm

21.33.370 Rm

21.33.4137 Rm

21.33.5249 Rm

Providing and fixing landing valve hydrants to type ‘A’ of I.S: 5290-1977 with 63mm dia S.S. instantaneous type single headed outlet, M.S. pipe, bend and flange of required size with blank caps and chain complete with instantaneous spring lock type G.M. female coupling of 63mm dia for connecting hose pipe.

Providing and fixing standard short size S.S. branch pipe (IS:903) with S.S. nozzle 20mm nominal bore outlet with standard instantaneous type 63mm dia coupling in all respects.

Providing and fixing 63mm dia 15m long rubberized fabric lined hose including S.S. male and female instantaneous type coupling, approved by fire authority, machine wound with copper. wire complete in all respects with hose conforming to IS:636 type-II and coupling conforming to IS: 903-1985 with ISI certification.

Providing and fixing pre fabricated weather proof lockable cabinet wall mounting or free standing type of size not less than 30" x 24" x 18" made out of MS sheet of 1.6 mm thickness and 4 mm thick glazed glass door. suitably marked on the outside with the letters "FIRE HOSE" including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint of approved shade complete in all respect. (For External Hydrants)

Providing and fixing pre fabricated with 1.6mm thick MS Sheet 5 mm thick glass door (with MS frame) of size 2.1 m x 0.9 m. Suitably marked on the outside with the letters "FIRE HOSE" including locking arrangement. All MS work to be in Red P.O. colour over appropriate primer. The above item is only for masonary fire station.

Providing and fixing standard fire mans axe with heavy duty insulated rubber handle.

Air cushion tank (air-vessel) 250 mm dia. x 1.0 M high with dished top, made of minimum 6 mm thick M.S. pipe/plate complete with 25 mm dia. Brass Air Valve (Ball valve, pressure gauge type), 25 mm dia. brass stop cock, nipple, tees, B46 elbow, pipe and all accessories as required incl. fixing brackets.

Providing and fixing MS black pipes as per IS 1239 (Part I) HEAVY Class including cutting, welding etc. complete with fittings viz Tees, Elbows, Bends, flanges, reducer, clamps, hanger etc. including painting with one coat of primer and two coat of synthetic enamel paint of approved make and shade

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

21.33.6157 Rm

21.33.793 Rm

21.33.82064 Rm

21.34

21.34.14 Each

21.34.21 Each

21.34.31 Each

21.35

21.35.1688 Each

21.35.210 Each

21.36

6 Each

21.37

6 Each

21.38

1 Set

21.39

1 Each

21.4

50 Rm

40mm dia

32mm dia

25mm dia

Providing and fixing C.I butterfly valve, wafer end type class PN 1.6 as per I.S:13095 or BS:5155, including necessary flanges, rubber gaskets, nuts, bolts, gaskets etc., complete

150mm nominal bore

80mm nominal bore

65mm nominal bore

"Providing, fixing, and testing of 15mm dia. Chrome finished sprinkler head with quartz bulb, set to operate at 68°C, complete as per given specifications. (UL/FM Approved) for corridor / public area or wherever required." Sprinkler pendant

Sprinkler upright

Providing and fixing electrically operated flow indicating switches with threaded connection for indicating water flow in sprinkler branch line with necessary junction box installed in accessible place. including cost of cable etc. complete. (Wiring from switches to panel and stair-case pressurisation not included).

Providing and fixing 25mm dia inspecting & testing assembly with S.S. isolation valve, S.S. sight glass byepass valve & connected to line drain complete in all respect as per standard practice of code including pressure gauges of approved make.

Providing and fixing modular construction annunciation panel for flow control switches having 5 zones , (3 working & 2 spare for future) complete in all respect and consisting of;

a) Fault indication for each zoneb) Fire/fault hooter.c) Alarm panel for fire/faultd) Battery for emergencye) Battery Chargerf) Mains supply

Providing & Fixing of Installation Control Valve 150mm dia with turbine type automatic Alarm Gong to be connected with control valve, drain & test valve and all other necessary components as per manufacturer's specifications complete as required.

Providing and fixing heavy duty copper armored cables 1.1 KVA grade including necessary support clamps at ceiling level and connection legs complete in all respects.Control cable 4 core 1.5 Sq.mm

21.41

21.41.1

24 Each

21.41.2

24 Each

Total

HAND APPLIANCES

Providing and fixing ISI marked portable fire extinguishers including intial fill & wall suspension bracket of the following type.

CO2 type 4.5 Kg. capacity Fire Extinguisher .flat base including valve , discharge hose of not less than 10 mm dia 1 m long and complete in all respects including intial fill wall suspension bracket and conforming to IS: 15683.

Providing and fixing 5 kg capacity ABC Stored Pressure type fire extinguisher ISI marked under IS:15683 complete with imported Mono Ammonium Phosphate based ABC Powder suitable for all classes of fire.

Original EstimateConstruction of building for Flexible Electronics Center IIT Kanpur

Rate Amount

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.000.00

0.000.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.000.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.000.000.00

0.000.000.000.000.00

0.000.00

0.000.00

0.00

0.000.000.000.00

0.00

0.00

0.000.000.000.000.00

0.000.000.000.00

0.000.00

0.000.000.000.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.000.00

0.000.000.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

Date post:	09-Jul-2016
Category:	Documents
Upload:	anantpawar
View:	214 times
Download:	2 times

Schedule

Documents