schedule of Rates - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/2420/Notice/GUJ... ·...

schedule of Rates

Line No.

Description UnitUnit Rate

1 Financial Limit

PART - A: COMPOUND WALL / CULVERT / KERB WALL

2

SITE CLEARANCE: Surface dressing of the ground including removing t rees, vegetation and making surface levelled and disposal of rubbish outside HPCL's premises to an unobjectionable place, as directed b y the Engineer in Charge.

SQM 5.8

3

MICRO LEVEL SITE CLEARENCE: Micro levelling and surface dressing where heaps ar e 230 mm height or less and depression 230 mm or less. Job includes me chanical dressing, making surface to line and level, compact ion of undulations filled with mechanical roller etc. all complete as directed by Engineer in Charge.

SQM 9.5

EXCAVATION:

EXCAVATION for foundation upto required depth below existing ground level in any type of soil except hard rock. Rate to include dressing the sides and bottom, bailing out water if encountered, shoring, strutting, back filling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within /outside HPCL's premises to an unobjectionable plac e, as directed by the Engineer in Charge including spreading, waterin g and compaction, complete .

4 Up to 2 mtr depth CUM 93.5

5 Above 2 mtr and upto 4 mtr depth CUM 121

EXCAVATION IN HARD ROCK: Description same as excavation except the soil will be hard rock and excavation shall be done by chiselling / pneumatic drilling (blasting is probhited)

6 For 0-2 mtr depth CUM 640


EXCAVATION IN SOFT ROCK: Earth work in excavation in soft rock above / below ground level. Rate to include dressing the sites and bottom, bailing o f water if encountered, shoring, shuttering, stacking the usab le material as per Engineer-In-Charge directions, disposal of surpus u nwanted materials to an unobjectionable place as directed by Engineer -in-charge. Job includes backfilling the excavated pit / trenches w ith available excavated usable material in layers 150 mm compacte d thickness, including watering, compaction by saturation, earth rammer, hand rammer, all complete as per specifications, drawing and Engineer-in-charge directions.

SIGN SEAL OF BIDDER

Line No.


8 For 0-2 mtr depth CUM 305


10

SAND FILLING: Supply and filling with clean locally available app roved quality sand in layers of 150 mm each including compacting by hand ramming and watering.

CUM 275

BOULDER PACKING: Providing and laying boulder packing / soling using 150 / 230 mm thick naturally formed quarry boulders for foundation tre nches / pits etc. (not R R stone) of approved quality, including dewaterin g contineously of accumulated water from any source and keeping the s urface dry for subsequent works, hand packing to line and level, f illing the voids with smaller size stone, binding material, hand ramming to desired levels, tools and plant complete etc., all labour, material s as per drawing and Engineer-in-charge directions.

11 150 mm thick SQM 66

12 230 mm thick SQM 102

13

DRY STONE PACKING: Providing rough stone dry packing in trapezoidal sh ape waste water / storm water drain in front of Retail Outlet. Job in cludes making earth profile as per Engineer-in-charge directions at sit e, to the natural slope and line, compacting the earth surface with hand ra mmer, placing of minimum 230 mm thick dry stone with flat surface to wards drain face, filling the voids with smaller size packing stones and merging with spall. The stone used shall be locally available Kh ondolite stone with flat surface making drain.

CUM 434

PCC WORK:

14

PCC 1:4:8 FOR FOUNDATION: Providing and laying PCC 1:4:8 using 40 mm and down size graded stone aggregates including machine mixing, providin g form work if required, placing, compacting by hand ramming, curi ng etc. complete.

CUM 1700

15

PCC 1:3:6 FOR FOUNDATION: Providing and laying PCC 1:3:6 using 40 mm and down size graded stone aggregates including machine mixing, providin g form work if required, placing, compacting by hand ramming, curi ng etc. complete.

CUM 1900

16

PCC 1:2:4 FOR DPC: Providing and laying 50 mm thick DPC in PCC 1:2:4 m ix with 6 to 12 mm size HBG aggregate in two layers of 20 mm thick wit h two coats of hot bitumen (Grade A- 90/S-90 conforming to IS:73) appl ied at rate 1.7 Kg per sq.mtr. over each layers as per specifications including cleaning, watering, the top surface of walls, centering, shut tering, placing, tamping, curing, sprinkling each layer of dry and s harp sand over the hot bitumen etc. all complete as per drawing, Engin eer-in-charge direction.

SQM 300

SIGN SEAL OF BIDDER

Line No.


17

PCC 1:2:4 FOR COPING: Providing and laying 60 mm average thickness coping in CC 1:2:4 mix using 6 to 12 mm stone aggregate with 40 mm project ion on either side of wall with drip mould. Rate to include 20 mm thic k plaster in CM 1:4 for fixing of glass pieces including mixing, provid ing necessary shuttering, compaction and curing. Thickness of cop ing at the ends shall be 40 mm and 80 mm at centre.

CUM 3100

18

PCC 1:2:4 FOR GROUTING ANGLE: Providing and laying PCC 1:2:4 mix using 20 mm to 1 2 mm stone aggregate including mixing, providing necessary shu ttering, compaction and curing.

CUM 3500

REINFORCEMENT CEMENT CONCRETE: Providing, mixing and placing RCC 1:1.5:3 mix with Ordinary Portland Cement using 20 mm and down size graded crushed agg regate including providing and fixing necessary plywood / steel shuttering, scaffolding, machine mixing, compacting by vibrator s, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel Reinforcement, which will be paid under a separate item. Concrete conforming to relevant specificatio ns of IS:456 Latest Edition.

19 FOOTINGS / PILE CAPS CUM 3600

20 COLUMNS / BEAMS CUM 3800

21 CULVERT SLAB / PRECAST SLABS CUM 4200

UNDER REAMED PILES: Providing RCC 1:1.5:3 for under reamed piles up to required depth with double bulbs as per IS:2911 etc. all complete. Rein forcement steel shall be paid separately. Pile cap shall be paid separate ly.

22 300 mm dia. pile RMT 757

23 230 mm dia. pile RMT 694

24

REINFORCEMENT STEEL: Supply, fabrication, hoisting and placing in positi on HYSD reinforcement bars conforming to IS:1786-Latest Edi tion Grade Fe 415 as per detailed drawing and specifications includin g cutting, bending and tying with 18 SWG binding wire complete. The ra tes shall be applicable for all heights and depths. Payment shal l be made as per reinforcement drawings and with theoretical weights only including all authorised laps and hooks.

MT 45000

BRICK MASONRY WORKS: Providing and constructing following brick masonry in CM 1:5 using first quality bricks of Class designation 35 (minim um) and conforming to IS:1077-1986 including providing all openings an d projections, raking the joints to 1 cm deep, scaffolding, soaking of br icks in water prior to use and curing etc. complete as per specifications.

SIGN SEAL OF BIDDER

Line No.


25SUB STRUCTURE: Providing and laying brick masonry as above for fou ndation below DPC level.

CUM 1756

26SUPER STRUCTURES: Providing and laying brick Masonry as above for sup erstructure above DPC level including scaffolding.

CUM 1896

RANDOM RUBBLE MASONRY: Providing and constructing Random Rubble Masonry wi th good quality stone in CM 1:5 for substructure & superstructure a s per IS:1597, Part-1, latest edition. Rate to include raking the joint s to 1 cm deep, providing through stones @ 2m C/C and curing etc. c omplete.

27 SUB STRUCTURE CUM 1381

28 SUPER STRUCTURE including scaffolding CUM 1569

29

RUBLE PITCHING: Providing 230mm thick Rubble pitching including sur face dressing, making required slope. Rate to exclude flush pointi ng which will be paid separately .

SQM 153

POINTING:

30Providing flush pointing in Ruble pitching with 1:3 cement mortar including curing etc. complete.

SQM 55

31Providing 12mm raised pointing in RR Masonry wall w ith 1:3 cement mortar including curing etc. complete.

SQM 62

32

PLASTERING: Providing and laying average 15 mm thick sand faced cement plaster in single coat in CM 1:4. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of bri ck and concrete surfaces, with a minimum overlap of 150 mm in all d irections and curing complete. No extra payment shall be made for additional thickness if required to achieve perfect line and l evel.

SQM 105

33

WATER PROOF CEMENT PAINT (SNOWCEM): Providing and applying 2 coats of snowcem to plaste red and concrete surfaces including providing necessary scaffolding, surface preparation etc. complete. If additional coats are required to obtain uniform and smooth finish, the same shall be carrie d out at no extra cost.

SQM 35

34

WEEP HOLES: Providing, fabricating and installing in place, 75 mm dia. PVC Pipes of various lengths & at places as directed at site on the masonry wall for water drainage.

RMT 196

SIGN SEAL OF BIDDER

Line No.


CHAIN LINK FENCING / BARBED WIRE FENCING:

35

STRUCTURAL STEEL: ANGLE IRON POST: Supply, fabrication, erection and grouting of 65 x 65 x 6 ISA post and supporting angles of specified length in 1:1.5:3 concrete grout at every 2.4 m C/C or as advised. Ra te to include fabrication of the post as per the specification, e recting, placing, grouting and painting of the posts with two coats o f synthetic enamel over two coats of Zinc Phosphate primer. Paints and primer shall be of SHALIMAR / BERGER / ASIAN make first quality only. Excavation and concrete will be paid separately under their respec tive items.

MT 51000

36

PIPE RAILING: Supply and fixing of 40 NB medium quality MS pipes confirming to IS:1239 latest edition for top and bottom railings to angle iron posts for fixing the edges of the chain link fencing. Rate in cludes fabricating, cutting, bending of the MS pipe, supply and fixing of MS clamps at every post, with nuts and bolts (all proper sized) and painting the railing with two coats of Zinc Phosphate primer and two coats of synthetic enamel paint after proper cleaning / scra pping. Paint and primer used shall be of SHALIMAR / BERGER / ASIAN m ake 1st quality only.

RMT 500

37

CHAIN LINK FENCING: Supply and fixing of 50 x 50 mm opening size 10 SWG GI chain link fencing to the angle iron post with 8 SWG GI hooks and nuts and railing with 14 SWG GI continuous wire (all details shall b e as per enclosed drawing ) up to a height of 1.8 m from the ground l evel. Rate to include unrolling the bundle, erecting, tightening and fixi ng at 300 mm C/C on the vertical portion of the posts to every top and bottom railing with 14 gauge MS wire.

SQM 325

38

BARBED WIRE FENCING: Providing and fixing 13 rows horizontal and two dia gnols with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm C /C. Angle iron post shall be paid separately. For payment purpose measurement shall be taken for the length of plot boundary. No measur ement shall be taken for 13 rows individually.

RMT 200

HUME PIPE:

39

Supplying, laying, joining and aligning 900mm NB NP 3 class RCC Hume pipes conforming to IS:458 Latest Edition below app roach road as directed. Rate to include joining with cement morta r, excavation up to required depth and providing and laying PCC 1:2:4 h aunching @ 1m C/C. Test certificates from manufacturer shall be s ubmitted and approved by EIC before use. (PCC 1:3:6 shall be pai d extra as per relevant item).

RMT 2629

SIGN SEAL OF BIDDER

Line No.


40

Supplying, laying, joining and aligning 600mm NB NP 3 class RCC Hume pipes conforming to IS:458 Latest Edition below app roach road /driveway as directed to the true line and level. R ate to include joining with cement mortar, providing and laying PCC 1:2:4 haunching @ 1m C/C. The PCC haunching shall be minimum 1.1m X 0.3m X 0.35m, curing of PCC haunching. Test certificates from manufactur er shall be submitted and approved by EIC before use. (PCC 1:3: 6 shall be paid extra as per relevant item).

RMT 1337

41

Supplying, laying, joining and aligning 300mm NB NP 3 class RCC Hume pipes conforming to IS:458 Latest Edition below app roach road /driveway as directed to the true line and level. R ate to include joining with cement mortar, providing and laying PCC 1:2:4 haunching @ 1m C/C. The PCC haunching shall be minimum 0.8m X 0.3m X 0.35m, curing of PCC haunching. Test certificates from manufactur er shall be submitted and approved by EIC before use. (PCC 1:3: 6 shall be paid extra as per relevant item)

RMT 563

SIGN SEAL OF BIDDER

Line No


PART -B : SALES BLDG. / CANOPY FOUNDATION

42

PRE-CONSTRUCTION ANTI TERMITE TREATMENT: Providing anti-termite treatment including diluting and injecting Neem base solution and creating a continuous barrier und er and alround the column pits, wall trenches, basement excavation, to p surface of plinth.

SQM 120

43

POST-CONSTRUCTION ANTI TERMITE TREATMENT: Providing post-construction anti-termite treatment in top surface of plinth filling, external perimeter of building belo w D.P.C. external perimeter of building over D.P.C. under apron, foun dation etc.

SQM 150

44

RUBBLE SOLING : Providing and laying 230 mm thick rubble soling inc luding hand packing, filling the interstices with chips, spalls and binding with grit and selected murrum, watering, compacting by hand r amming.

SQM 145

45

MURRUM FILLING: Supplying and filling good quality murrum in layers of 150 mm thick including watering and compacting till maximum comp action is achieved as directed by Engineer In Charge. Compact ed volume shall be considered for measurements.

CUM 200

PLAIN CEMENT CONCRETE: Providing and laying PCC of following mix including providing and fixing form work, machine mixing, compaction and cu ring etc. complete as per specification.

46

PCC BEDDING : Providing and laying Plain Cement Concrete of 1:2:4 mix grade with 12mm and down size HBG as coarse aggregate, river s and as fine aggregate and cement min. 330 Kg./Cu.M. for bedding etc., including providin

CUM 2747

BRICK MASONARY: Providing and constructing brick masonry in CM 1:5 using bricks having minimum compressive strength 35 Kg/cm2 and c onforming to IS: 1077- Latest Edition including providing all op enings and projections as per the drawing, raking the joints to 1 cm deep, scaffolding, soaking of bricks prior to use and curing etc. complete as per specifications.

47

115 mm thick in partition walls in CM 1:4. Rate to include providing 75 mm thick RCC 1:1.5:3 bands using 2 nos., 8 mm dia. Torsteel reinforcement at every 1 M height of wall including shuttering. Steel reinforcement shall be paid for separately.

SQM 217

SIGN AND SEAL OF BIDDER

Line No


PLASTERING:

48

SMOOTH CEMENT PLASTER FOR CEILING / CHAJJA: Providing and applying 6 mm thick plaster in CM 1:3 to ceiling and bottom surface of chajja using screened sand includ ing finishing smooth and providing drip moulds at chajja edges, s caffolding and curing etc. complete

SQM 95

49

SMOOTH CEMENT PLASTERING (INTERNAL WALL): Providing and laying 15mm thick smooth cement plast ering in 1:4 CM in single coat to all the interior walls including pro viding necessary scaffolding, chicken wire mesh at all joints of bri ck and concrete surfaces, with a minimum overlap of 150 mm in all d irections and additional thickness if required to achieve perfect line and level without any extra cost.

SQM 100

CERAMIC TILE FLOORING : Providing and laying matt finish 1st quality Ceram ic tiles of 6/8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design an d pattern over bedding of cement mortar of 30mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete.

50 400mmx400mm SQM 600

51 300mmx300mm SQM 575

52

CERAMIC TILE SKIRTING : Ceramic tiles skirting 150 mm in height using C.M. bedding 1:3 & fixed with neat cement slurry.Rate to include all necessa ry chipping of brick masonary/concrete so that skirting is projecting un iformly 6mm from plaster thickness. All vertical joints of skirting shall match with floor tile spacing uniformly as per standard specifications an d EIC directions.

RMT 100

POLISHED VITRIFIED CERAMIC TILE FLOORING: Providing and laying 1st quality polished vitrified Ceramic tiles of 8 mm thick of followg sizes on flooring (approved make & shade, free from cracks, warpage, fissures and flakes, straight edge s and perfect corner) laid at right angle as per design and pattern over a bedding of cement mortar of 30 mm thick CM 1:5, finishing the joints neatly with white cement mixed with matching colour pigment and finis h in all respect and all material and labour complete.

53600mm X 600mm of Jonson make. Catlog No. J/N- 2'x2' -Salt & Pepper. Basic rate @ Rs.850/sqm.

SQM 1400


Line No


54

VITRIFIED CERAMIC TILE SKIRTING : Ceramic tiles skirting 150 mm in height using C.M. bedding 1:3 & fixed with neat cement slurry. Rate to include all necess ary chipping of brick masonry / concrete so that skirting is projecting u niformly 6mm from plaster thickness. All vertical joints of skirting shall match with floor tile spacing uniformly as per standard specifications an d EIC directions.

SQM 1020


Line No


55

IPS FLOORING: Providing, mixing and laying 50 mm thick Indian Pat ent Stone flooring in PCC 1:2:4 mix concrete with 12 mm and down size gra ded crushed aggregate including providing and fixing 4 x 25 mm size glass strips in 1m X 1m panels, casting the concrete compacting and finishing the surface smooth using cement slurry.

SQM 170

56

GRANITE SKIRTING : Providing and fixing 10mm thick jet black granite s kirting of 100 mm height free from crack fissures & flakes with strai ght edges & perfect corners fixed at right angles with neat cement past e and finishing the joint with white cement mixed with matching colour pigment.

RMT 160


Line No


57

CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 X 200 mm size (Kajaria make ) first quality, free from crack fissures & flakes wi th straight edges & perfect corners fixed at right angles as per the de sign and pattern, including applying 12mm thick backing plaster in 1: 4 CM and fixing the tiles with neat cement paste, finishing the joints with white cement mixed with colouring pigments to match the colour o f tiles properly cured & finished in all respects etc. complete.

SQM 600

58 Same as above but laying and fixing designed bord er tile SQM 750

59

20MM THICK GRANITE CLADDING FOR CURTAIN WALL: Providing and fixing machine cut and polished black Granite slab of thickness of 20 mm selected & sorted for uniformity in colour, free from cracks, fissures and flakes with straight edges and perfect corners using 50mm X 20mm X 3mm SS T shaped cleats of 100mm long. The cleats are fixed over the wall with M12X100mm long GI fasteners by providing 2 nos. 12mm X 25mm size slots and drillin g the wall. Rate to include making necessary grooves in granite slab, f inishing the joints neatly with white cement mixed with coloring pigmen t to match colour, polished and finished in all respect, all materials and labour complete.

SQM 3000

60

KOTA STONE STEPS: Providing and fixing 20 mm thick one piece Kota sto ne slabs with 25mm bedding CM 1:3, cement slurry and machine polishing on one side for risers of steps, treads and shelf slab including no sing etc. complete.

SQM 800

61

SILL SLAB : Providing and laying 20 mm thick machine cut & mach ine polished jet black granite strips over a bedding of 20 mm thick 1:5 CM for window sills. The strips shall be of single piece only as per width of window wall and project 12 mm beyond the face of the wall.

SQM 2300

62

ULTRA CHUTURA WALK WAY TILING : Supply and fixing concrete tile of EUROCON make, ap proved shade of 20mm thickness for flooring including providing 20 mm thick 1:5 cement mortar bed and a floating coat of neat cemen t slurry, finishing the joints with white cement mixed with matching co lour pigment, cleaning the surface with dilute sulphuric acid etc . complete.

SQM 1000

63 Same as above item 62 but for treads and risers SQ M 1000

WATER PROOFING


Line No


64

TERRACE: Providing and laying integral cement based water pr oofing of average 100 mm thick as per specifications given below: a) cleaning RCC slab and applying neat cement slurry mixed with waterpro ofing compound. b) Providing and laying brickbat coba in CM 1:4 mix ed with water proofing compound and curing for a period of 24 hou rs. c) Laying of 25 mm thick PCC 1:1.5:3 mix with 6 mm and down size co arse aggregate and water proofing compound, finishing smooth, maki ng half round vata at the junction of parapet wall and slab and c uring for 10 days. Note: Contractor will be required to submit a guara ntee in respect of performance of waterproofing for 10 years on a stam p-paper. In addition to this, an amount equal to 10% of cost of waterproofing items shall be retained as retention money for 2 years fr om the date of completion, which shall be returned with out intere st only after successful completion of this period.

SQM 350

65

Water proofing on top of chajja with 25mm thick PCC 1:1.5:3 with 6mm and down size stone aggregate mixed with water proo fing compound, finishing smooth, making half round vata at the jun ction of chajja and wall, curing etc. complete.

SQM 220

66

R.C.C FOR PRECAST COVER SLABS : Providing and laying precast RCC slabs of required size with 1:2:4 nominal mix using 20 mm and down size crushed stone aggregatess including wooden form work, plywood sheet shutterin g, mixing, compacting, pond curing for 14 days etc. as per IS: 456, transporting from the place of casting. Reinforcement shall be p aid separately.

CUM 3600


Line No


PAINTING :

67

WHITEWASH : Providing and applying 3 coats of white wash to pl astered and concrete surfaces including providing necessary sca ffolding, surface preparation, mixing DDL binder, blue etc. complete as per IS: 712- Latest Edition. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost.

SQM 10

68

APEX PAINT: Providing and applying 2 coats of apex paint to all exterior surfaces over a coat of premier as per manufacturer's specif ication including necessary scaffolding, curing etc., complete. If ad ditional coats are required to obtain uniform and smooth finish, the s ame shall be carried out at no extra cost.

SQM 80

69

OIL BOUND DISTEMPER: Providing and applying 2 coats ( first coat with br ush and final coat with Roller) of OBD of approved make and shade on all su rfaces and heights to give an even shade including priming coat and f ull putty after thoroughly brushing the surface free from mortar dr opping and other foreign matter and also including preparing the sur face even and sand papered smooth etc., all material and labour comple te.

SQM 45

70

ACRYLIC EMULSION PAINT (INTERIOR GRADE): Providing and applying 2 coats (first coat with bru sh and final coat with Roller) of Acrylic Emulsion paint of approved make and shade on all surfaces and heights to give an even shade includin g primer and full putty after thoroughly brushing the surface free fr om mortar dropping and other foreign matter and also including prepari ng the surface even and sand papered smooth etc., all material and labo ur complete.

SQM 70

71

ACRYLIC EMULSION PAINT (EXTERIOR GRADE): Providing and applying 3 coats of acrylic anti fung al cement paint including primer of BERGER (Weather coat) or approv ed equivalent make and shade to all the exterior surfaces as per manufacturer's specifications including providing necessary scaffo lding, curing, etc. complete. If additional coats are required to obtai n uniform finish, the same shall be carried out at no extra cost as direc ted by Engineer In Charge.

SQM 85

72

WATER PROOF CEMENT PAINT: Providing and applying 2 coats of water proof cemen t paint of SNOWCEM INDIA make and of required shades on all s urfaces and heights to give an even shade after thoroughly brus hing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material, scaffolding and labour complete.

SQM 35


Line No


73

SANDTEX MATT: Providing and applying 2 coats of Sandtex matt pain t of SNOWCEM INDIA make and of required shades on all surfaces a nd heights to give an even shade including primer coat of snowcem afte r thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface eve n and sand papered smooth etc., all material, scaffolding and labour c omplete.

SQM 70

74

SYNTHETIC ENAMEL PAINT OVER WALL: Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and of required shades on wal l to give an even shade including a priming coat after thoroughly bru shing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material, scaffolding and labour complete.

SQM 60

75

SYNTHETIC ENAMEL PAINT OVER STEEL SURFACE : Providi ng and applying 2 coats of synthetic enamel paint 1st qual ity of approved manufacturer and shades on steel surface to give an even shade including two coats of red oxide primer after thoro ughly brushing the surface free from rust and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material labour complete.

SQM 65

76Providing and fixing MS grill fabricated from MS fl at / square bar as per approved design including painting with two coats o f red oxide and two coats of synthetic enamel paint.

KG 50

77Providing and fixing MS ladder fabricated from MS a ngle and plain rod as per approved design including painting with two coats of red oxide and two coats of synthetic enamel paint.

KG 55

DOORS, WINDOWS, VENTILATORS:

78

ALUMINUM GLAZED DOOR / FIXED GLAZING WITH 12MM GLASS: Providing and fixing Aluminum glazed door/ fixed gl azing with 25 micron coloured anodized aluminum section minimum w all thickness of not less than 2 mm with extruded built up section o f approved make and weight ratio joints mitred ad joint with heavy duty aluminium pressure die cast cleats with fins to match the sec tion of frames conforming to approved section and shutterconformin g to approved sections and glazed with 12 mm thick glass fixed to shutter with aluminium snap beading and neoprene / PVC gaskets/C P brass/stainless steel screws and fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expans ion hold fastners including necessary filling up of gaps at junctions , at top, bottom and sides with requisite PVC/neoprene felt/polysulphide sealant/sillicon sealant etc. all complete as per architectural draw ing. Aluminium anodised shop front (Doors & fixed glazing) with fr ames at top & bottom and at two ends of INDAL make or equivalent with section no. 9205 of size 101.5 x 44.45x 3 with weight of 2.342 kg/m. Round acrylic handle and locking arrangement to be provided for m a

SQM 3000


Line No


79

HYDRAULIC FLOOR SPRINGS: Providing and fixing double action hydrauclic floor springs of approved brand ( HARDWYN/EVERITE) conforming to IS:6315 for aluminium doors. Rate to include cutting of floors as require d, embeding in floors and cover plates etc. complete as per specification s.

Nos 1900

80

ALUMINIUM PANELLED DOOR: Providing and fixing 25 micron colored anodised sin gle leaf aluminium door with minimum wall thickness of not less than 2 mm, joints mitred ad jointed with heavy duty aluminium pressure die c ast cleats with fins to match the section of frames conforming to INDAL section 9221or equivalent section (Jindal/HIndalco) and shutter co nforming to INDAL section 9200, 9201, 9202 and 9240 or equivalent sec tion (Jindal/Hindalco), fully panelled with 9 mm thick p relaminated 3 layers medium density (exterior grade) particle board Grad e-1, type -II conforming to IS:12823 bonded with phenolformaldehy de synthetic resin of approved brand and manufacturer fixed to s hutter with aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wall with requ isite rawl plugs and screw or with fixing clips or with expansion hold f astners including necessary filling up of gaps at junctions, at top, bottom and sides with requisitePVC/neoprene felt/polysulphide sealant/sillicon sea lant etc. all complete as per architectural drawing. Aluminium door section of IN DAL make or equivalent make with the following section: Main frame on all sides - 9221 -101.5 x 44.45 x 2.5 of weight 1.975 kg/mtr. S hutter vertical frame- 9202 - 50 x 44.5 x 2.5 of weight 1.202 kg/mtr. Shut ter top frame - 9201- 50x44.5x2.5 of weight 1.299 kg/mtr. Shutter middle frame - 9129-50x45x2.5 of weight 1.292 kg/mtr. Shutter bottom frame - 9200-100x44.5 x2.5 of weight 1.974 kg/mtr. Door handle -5140 - 100x 30 x 2.5 of weight 0.988 kg/mtr. Glazing clip - 4660 - 17.8 x 17.6x 1.3 of weight 0.169 kg/mtr.

SQM 2800


Line No


ALUMINIUM WINDOWS:

81

ALUMINIUM WINDOWS(OPENABLE): Providing and fixing 25 micron colour anodised alum inium glazed windows with 4 mm glass & extruded built up section of wall thickness not less than 1.5 mm and approve make with glass pa nel fixed to side hung shutter with aluminium snap beading and neopre ne / PVC gasket / CP Brass / Stainless Steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expans ion hold fasteners including

SQM 2600

necessary filling up of gaps at junctions,at top,bo ttom and sides with PVC/neoprene felt/polusilphide sealant /silicon sea lant including heavy duty handle cum locking arrangement etc. all comple te as advised by EIC. Al. window section of INDAL make or equivalent approved make with following section:

Outer frame -2082 - 34 X 44.45 X 28.5 X 2 of weigh t @ 0.554 Kg/Mtr

Shutter frame - 4124 - 34 X 44.5 x 28.5 X 1.5 of weight @ 0.494 Kg/Mtr

Mullion - 9139 - 57 X 34 x 25 X 2 of weight @ 0.81 0 Kg/Mtr

Cleat angle - 2081 - 50 X 50 x 4.9 of weight @ 1. 177 Kg/Mtr

Glazing clip : 4125 - 31 X 17.5 X 1.2 of weight @ 0 .184 kg/mtr

82 Same as above but Aluminium sliding windows SQM 300 0

83

ALUMINIUM LOUVRED VENTILATOR: Providing and fixing colour anodised aluminium vent ilator with extruded built up section of wall thickness not les s than 1.5 mm and approved make glazed with 4 mm thick opaque glass louver 100mm wide.

SQM 2600

84

ALUMINIUM DOOR/FIXED GLAZING WITH 6MM GLASS: Providing and fixing 25 micron coloured anodised al uminium fixed glazing/aluminium door with 6 mm glass extruded bui lt up section of wall thickness not less than 1.5 mm and approved ma ke with glass panel fixed with aluminium snap beading / neoprene / PVC gasket / CP Brass / Stainless Steel screws fixed to the wall wi th requisite rawl plugs and screw or with fixing clips or with expansion ho ld fasteners including necessary filling up of gaps at junctions , at top, bottom and sides with PVC/neoprene felt/polusilphide sealant / silicon sealant etc. all complete as advised by EIC. Al. section of INDA L make or equivalent approved make with following sections:

SQM 3500

Outer frame -2082 - 34 X 44.45 X 28.5 X 2 of weigh t @ 0.554 Kg/Mtr

Mullion - 9139 - 57 X 34 x 25 X 2 of weight @ 0.81 0 Kg/Mtr

Cleat angle - 2081 - 50 X 50 x 4.9 of weight @ 1. 177 Kg/Mtr


Line No


Glazing clip : 4125 - 31 X 17.5 X 1.2 of weight @ 0 .184 kg/mtr

Bottom 900 mm height shall be with 9mm thick both s ide prelaminated NOVOPAN board. The door shall be provided with Al. handle towerbolt, locking arrangement etc. complete .

85

ALUMINIUM PANELLED DOOR WITH BISON LAM: Providing and fixing aluminium door to concrete and brick wor k with minimum wall thickness of not less than 2 mm , with outer door frame section of frames conforming to INDAL series section 9221 or equivalent section( Jindal/HIndalco)and Door shutter conforming to INDA L section 9200, 9201, 9202,9219 and 9240 or equivalent section (Jin dal/Hindalco) with 9 mm thk Pre laminated both side Bison lam sheet ( Ce ment particle Board)fixed to shutter with aluminum snap beading a nd Neopren/ PVC gasket/CP Brass/SS screws .fixed to the wall with r equisite rawl plugs and screw or with fixing clips or with expansion ho ld fastners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC/neoprene felt/polysulphide sealant/si llicon sealant etc all complete including hard ware such as tower bolts fr om inside and Aluminum handle and Aluminum aldrop on both sides e tc complete as per architectural drawing.

SQM 3200

86

STEEL WINDOWS: Supply, fabrication and fixing of MS glazed window s using approved Z sections with 4mm plain glass including providing g rill with 12mm sqare bar @100mm c/c, painting with two coats of re d oxide primer and two coats of sysnthetic enamel paint, handle, stay arrangement etc. complete.

SQM 2100

87

STEEL DOORS : Supply, fabrication and fixing of MS door using 35x 35x5mm angle frame and 25x25x3 mm angle members including bracings wit h 16 gauge MS sheet stich welded to Door shutter frame complete a s per approved drawing, painting with two coats of red oxide prime r and two coats of synthetic enamel paint, handle, stay arrangement, tower bolt etc. complete.

SQM 2280

FLUSH DOOR : Providing and fixing solid core flush door in singl e leaf 35mm thick commercial plywork of seasoned wood without ventila tor. Door frame to be made of 60mm x 100mm teak wood with wrough ir on hold fasts. Door to be fitted with brass fitting-hinges, handle s on both sides, tower bolts etc. complete. Frame to be painted in three c oats of sysnthetic enamel paint over a coat of wood primer including s crapping, surface preparation etc. complete. Door (leaf) to be lamina ted on both sides with laminations 1.5 mm thick and grey in colour of approved make/brand.

88 (i) door size 900mm x 2100mm NOS 3168

89 (ii) door size 750mm x 2100mm NOS 3916


Line No


90

ALUMINIUM PANEL DOOR: Providing and fixing door shutters made of Aluminiu m panel sheets 3"x1.5" aluminium styles and rails and EPDN rubber for pasted sealing with Aluminium frame, hinges, handles, tower bolts etc., complete.

SQM 2500

91

ROLLING SHUTTER : Supply, fabrication and fixing of MS rolling shutte r of the following specifications including grill window of 300 mm hei ght at eye level for visibility even in closed position. Code: Conformin g to IS 6248-1979 Type: Self Coiling type (manual), Curtains: Interlo cking cold rolled lath section of 0.8 mm thickness. Lock plate: MS sheet o f 3.15 mm thick reinforced with MS angles of 35 X 35 mm. Guide chan nel: MS sheets of 3.5 mm thick. Bracket Plate: MS sheet of 0.9 mm thi ck hood covers. Locking handle : To be provided suitably. Rate shal l include providing and fixing holdfasts and painting two coats of enam el paint of approved make and shade over two ocats of zinc phosphate pri mer.

SQM 1600

92 Grill in rolling shutter SQM 2260


Line No


DISPLAY SHELVING / STORAGE

93

DISPLAY SHELF: Providing & fixing (as shown in standard drawing) i n position 12 mm thk plain glass of Modi Guard / Asahi make with pol ished edges in the grooves between the 25 mm thick exterior grade MDF board planks at 375 mm C/C & 300 wide. The vertical memebers of the MDF planks are at every 1200 mm C/C. The exposed surface of the MD F board shall be finished with 1.5 mm thick lamination of approved c olour & combination of colours with teak wood beadings on edges. The ap proved brand for the lamination shall be Formica / Greenlam / Sundek . The shelf shall be movable type fixed with wheels.

SQM 3030

94Same as above but for storage and shelves shall be with 25mm MDF board

SQM 7110

MISCELLANEOUS

95Providing & fixing MS fan hooks with 16 mm dia MS b ar bent to shape with hooked ends in RCC Slab during laying includin g painting the exposed portion.

Nos 95

96MORTICE LOCK: Providing & fixing GODREJ or equivalent make six le ver lock (Cylindrical/ Round Head ) including all necessary hardware etc.

NOS 855

97 DOOR CLOSER : Providing and fixing door closer of Hardwin/Everit e make size no. 2

NOS 1765

98

STRUCTURAL STEEL WORK FOR SERVICE BAY: Supplying, erecting and fixing in position Pre- fab ricated structures at all elevations for service bay using structural ste el sections conforming to IS:2062, including cutting, welding or bolting, supply of bolts/nuts/washers etc. complete as per drawings in cluding surface preparation and applying one coat of Zinc Phosphate Primer before erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complet e. (No welding is permitted at site). The rate quoted shall include c ost of bolts, nuts, washers, welding and electrodes and any other consu mables required for completing the work.

MT 51000

Supply, erection and fixing of corrugated asbestos cement sheet of Everest make or approved equivalent for service bay including supply and fixing of bitumen / GI washer, J bolt etc.

99 For roof SQM 225

100 For side sheet including gable end SQM 2120

101

GYPSUM BOARD FALSE CEILING : Providing and fixing Gyp board false ceiling with r equired accessories INDIA GYPSUM make including painting with two coat s of plastic emulsion paint.

SQM 570

102Supply, fabrication and erection of MS spiral stair way as per approved design, section etc.

KG 55


Line No


PLUMBING AND SANITARY WORK:WATER CLOSETS

103

EUROPEAN TYPE : Supplying and fixing coloured (pastel colour) vitre ous china European type water closet comprising of the the following a ccessories including cutting and making good the walls & floors wherever required complete as directed by Engineer In Charge A) Coloured (past el colour) viterous china pedestal type European water closet with P or S trap of Hindware sanitaryware standard model or equivalent approved make as per the direction of Engineer In Charge. B) 15mm NB brass a ngle valve as per ISI of approved brand as per the direction of Engin eer In Charge C) 15 mm NB CP inlet connection with Brass unions at the ends. D) Commander make or equivalent matching colour polypr opylene seat cover with necessary brass hinges and rubber bushes etc. E) WC connector with neoprene rubber etc. F) 10 litres ca pacity low level plastic cistern of matching colour parry slimline m ake or approved equivalent with necessary fittings, brackets, screw s, etc. all complete.

NOS 3525


Line No


104

INDIAN WATER CLOSET : Supplying and fixing coloured (pastel colour) vitre ous china Orissa Pan type water closet comprising of the the following a ccessories including cutting and making good the walls & floors wherever required complete as directed by Engineer In Charge A). Coloured (pas tel colour) viterous china 580 mm orissa pan water closet of Hinduatn sa nitaryware or any equivalent make with P or S trap B) 10 litres capac ity hi-grade engineering plastic low level flushing cistern of m atching colour parry slimline make, model no. 8068 or approved equivalen t make with necessary fittings, brackets, screws etc. all compl ete C) 32 mm PVC flush pipe 10Kg/sq.cm quality of approved length wi th necessary fittings, clamps etc D) 15 mm NB CP inlet connectio ns with brass union at the ends E) 15mm NB brass angle valve as per ISI of approved brand as per the direction of Engineer In Charge F) WC co nnector with neoprene rubber.

NOS 3767

105

URINALS : Supplying and fixing coloured (pastel colours) vite rous china flat back urinal of size 300mm X 400mm with integrated overfl ow of Hindustan Sanitary or equivalent approved make with CP flush valve, CP pipe connection, CP waste coupling, CP Brass bottle trap , 32 mm PVC waste line of required length etc. all complete as per the direction of Engineer In Charge.

NOS 1200

106

URINAL DIVISION PLATE : Providing and fixing 1200 x 450 x 20 mm size granit e partition plate between urinals including cutting masonary / concre te surface to required size, fixing the division plate on the cer amic tiles by means of SS clamps, nuts & bolts, polishing all exposed surf ace etc. all complete as directed by Engineer In Charge.

NOS 2200

107

HAND WASH BASIN: Providing and fixing coloured (pastel colours) wash basins of size 550 x 400 mm without pedestal Including the following acc essories: -15mm brass CP Jaquar make (Cat.no.093) stop cock -1 No . -15mm CP connections from the above stop cock to pillar cock - 1 No. -32mm dia waste coupling, CP brass chain and rubber stopper. -30mm bottle trap Jaquar make with cleaning eye, extension piece and wall flange. -Providing and fixing brass CP Jaquar make 13mm half turn pillar cock.(Cat. no.011). Rate to include supply, paintin g and fixing of necessary CI brackets with nuts and bolts and fixin g the wash basin with all necessary connections in walls.

NOS 2225

108

MIRROR : Providing and fixing bevelled edge mirror of superi or glass of 5.5 mm thick & 600 x 600 mm size of BELGIUM GLASS or any o ther equivalent make, 3mm thick felt backing or 6 mm asbestos sheet or with wooden beads allround of specified size and fixed with woo den plugs with CP brass screws and cup washers etc all complete as di rected by Engineer In Charge.

NOS 600


Line No


109SOAP TRAY: Providing and fixing readymade CP brass soap tray n ear wash basin with CP brass screws of approved make.

NOS 200


Line No


110LIQUID SOAP DISPENSERS : Providing and fixing readymade CP brass liquid soap dispenser near wash basin with CP brass screws of approved make.

NOS 510

111

TOILET PAPER HOLDER : Supplying and fixing of 150 x 150 mm pastel coloure d toilet paper holder of Hindustan Sanitary ware or equivalent app roved make at required position and elevation as directed. Rate t o include making good the chases in walls after fixing the above.

NOS 350

112

TOWEL RAIL: Providing and fixing CP brass towel rail of 20 mm d ia and 600 mm long including all accessories such as brackets (coloure d), fixed and anchoring etc. complete as directed.

NOS 400

STOP COCKS AND BIB COCKS: Providing and fixing in position CP brass stop cock s and bib cocks of heavy duty type ISI marked of approved make:

113 15mm dia stop cocks NOS 350

114 15mm dia bib cocks NOS 300

115 15mm dia Pillar cocks (Short body) NOS 465

116 15mm dia Half turn cocks NOS 395

CONCEALED GI PIPING : Providing & fixing followg size medium grade GI pip es of TATA/ JINDAL make conforming to IS:1239 concealed in the walls/u nder the concrete floors including making chases in the walls/concret e floors,fixing with clamps at every 1m C/C, necessary tees, bends, elbo ws, plugs, nipples, unions, testing of pipelines for leaks upto a pres sure of 6 Kg/sq cm. , painting the pipes with hot bitumen, wrapping the p ipes with hessian cloth and making chases of the walls good after pip ing complete.

117 15 mm nominal bore RMT 125


EXPOSED GI PIPING : Description same as above but providing, laying and fixing GI medium grades pipes in open on brick or RCC surface with t he help of MS 'U' clamps at every 1 m and at every turn.




Providing & fixing following size brass full way ga te valve ISI marked & of Leader/GG make or approved equivalent as directe d by Enginner In Charge.

122 25 mm dia NOS 600

123 15 mm dia NOS 400


Line No


124

WATER TANK : Supplying and installation of HDPE water tanks Sint ex / Fusion / Polycon make of 1000 litre capacity including 300 m m high brick masonry pedestal of 230mm thick in CM 1:5, providi ng 75mm thick RCC 1:2:4 slab with reinforcement 8mm tor @150mm c/c, lifting the tank, making all necessary GI connections to inlet, outle t, and overflow nozzles and cleaning the tank before commissioning.

NOS 5650

PVC SOIL / WASTE / RAIN WATER PIPES : Supplying and laying the following size PVC pipes o f 4 Kg/sq cm. pressure rating including plain or door type bends , shoes, offsets, clamps junctions, tees, etc, complete.

125 110 mm dia RMT 275


Line No


126 80 mm dia RMT 210

UPVC PIPES : Providing and laying unplasicides polyvinyl chlorid e (UPVC) pipes confirming to IS : 4985 including all necessary fit ting to IS/BS 4514 and other accessories including connections etc., compl ete as per drawings or as directed at site.

127 90 mm dia 4Kg/sqcm RMT 150




131

NAHANI (FLOOR) TRAP : Providing and fixing PVC floor trap of self cleansi ng design conforming to IS specs with 100mm inlet, 75mm outlet and 150mm CP hinged grating of 6mm thick with rim. Rate shall include m aking all necessary leak proof connections etc.

NOS 610

132

STONE WARE PIPES : Providing and laying 150mm dia. salt glazed stonewa re pipes conforming to IS 651 Grade-A including bends, tees etc, excavation of trenches, 100 mm thick PCC 1:4:8 bedding, providing PCC 1:2:4 haunches @ 0.5m c/c, filing the joints with tarred gasket, plastering with 1:3 cement mortar smoke testing of joints, backfill ing the trenches with excavated earth, watering, ramming etc., complete.

RMT 225

GULLY TRAP WITH CHAMBER : Providing and fixing square mouth gully trap includ ing constructing 300 X 300 MM internal size brick masonry chamber with 2 30mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thi ck PCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover with frame etc. complete.

133 600 x 600 mm (Internal dimensions) with 750 mm d epth NOS 1165

134 450 x 450 mm (Internal dimensions) with 600 mm d epth NOS 3220

135

SEPTIC TANK : Providing & constructing septic tank of size 1200x2 000x1800mm depth with excavation, PCC1:4:8 100mm thick bed, 345/230m m thick brick masonry wall in CM 1:5, RCC1:2:4 100mm thick slab w ith 8mm tor steel @150c/c both way, 115mm thick baffle wall with RCC beam at bottom,12mm thick smooth cement plaster with water proofing compound inside and exposed outside portion, provid ing 600mm X 600mm size medium duty CI cover, providing 75mm dia PVC vent pipe etc. complete.

NOS 18140

136SOAK PIT : Providing and constructing soak pit of 2.5m dia (in ternal) and 2m depth as per drawing.

NOS 8370

ELECTRIFICATION


Line No


137

POINT WIRING FOR LIGHT / FAN WITH MODULAR PLATE SWITCHES ANCHOR / MK / LEGRAND: Providing and laying point wiring in concealed cond uits for the following points using specified 1100V grade PVC in sulated, FRLS multistranded 3 x 1.5 sqmm copper conductor wires. Rate to include supplying, laying and securing in position in roof slabs and brick walls or concrete columns 25 mm dia rigid PVC conduits of approved make with necessary accessories and junction boxes/pull boxes. Providing and fixing in the brick wall flush type metal switc h boxes of approved make, shade and sufficient size to accommodate all 6A Modular switches / 3 pin socket, screws, holders, ceiling r oses and the fan regulator wherever required. Rate to include wall c hasing and rough plastering. Providing and fixing single pole 5A mod ular plate switches of MK or ANCHOR ROMA make of approved colour. One s witch shall be provided for each light and fan point. Rate to incl ude providing main circuit wiring from DB to switch boards with 2.5 sqmm copper wire also.

NOS 540

138 Same as above but for 5A socket controlled by one 5A switch on the same lighting board

Nos 865

139Same as above but for 5A socket controlled by one 5 A switch independently mounted including providing wiring w ith 3 runs of 1.5 sqmm pvc insulated copper wire through PVC conduit

Nos 775

140

Same as above but for 5/15A socket controlled by 15 A switch independently mounted including providing wiring w ith 2 runs of 2.5 sqmm and 1 run of 1.5 sqmm PVC insulated copper wir e through PVC conduit.

Nos 375


Line No


141

Same as above but for AC point with 2 runs of 4 sqm m (P&N) and 1 run of 2.5 sqmm (earthing) PVC insulated, FRLS multistr and copper cable in 25 mm dia PVC conduit from MCBDB to 20 A power sock et. The conduit shall be partly/fully concealed in all types of wal l, ceiling etc. complete with all accessories, wiring, termination, connecte d civil works, rough plastering etc. including supply and fixing of 20A industrial socket controlled by 20A SPMCB of MDS/HAVELS make.

NOS 695

Supply, laying, and commissioning of wiring using f ollowing sizes of PVC insulated, FRLS, unsheathed, multistraned copp er wire drawn in PVC conduits. Rate to include supply of 16 GI fish wire, conduits & accessories, wiring, terminations etc. complete.

1424 runs of 10 sq mm and 1 run of 6 sqmm copper wire in 40 mm dia PVC conduit from panel to Distribution Boards.

RMT 285

1434 runs of 6 sqmm and 1 run of 4 sqmm copper wire in 32 mm dia PVC conduict from panel to Distribution Boards.

RMT 170

144CEILING FANS : Supplying and fixing of the ceiling fans of Crompto n/GE/Polar with detail as below :

NOS 1960

Sweep :1400 mm

Colour :White

Bearing type :Double ball bearing

Down Rod : Clear 300 mm long

Regulator : Electronic type ANCHOR/MK make

Accessories : Screws, wall nuts etc.

EXHAUST FANS

145Supply, fixing and commissioning of 305 mm dia. Exh aust fans including bird louvers, frame works and other civil works like chipping and making the surface good etc.

NOS 1570

146 SAME AS ABOVE BUT 230MM DIA NOS 1350

LIGHT FIXTURES: Supply, fixing and commissioning of following light fittings. Rate to include all accessories, interconnection of wires f rom ceiling rose to the fittings and fluorescent tube /GLS/PL lamps, copper choke etc.

1471 x 36 W tube light fitting with lamp Philips make cat no. TCS 19/136 HPF or equivalent .

NOS 1750

1481 x 60W spot light luminaire with 1 meter track inc luding lamp Philips make cat no. DGN 451 or equivalent for display she lving

NOS 300

1491 x 60 W Bulk head luminaire including lamp Phillps cat no. NXC 101 or equivalent (Outside building).

NOS 513

150 Angle holder Anchor make including lamp 60W (To ilets). NOS 60

1511 x 36 W tube light fitting including lamp Phillps cat no TMS 21/136 HPF or equivalent ( stores, service area)

NOS 797


Line No


1522 x 36 W tube light fitting including lamp Phillps cat no TBS 50/236 HPF or equivalent (for false ceiling area)

NOS 2760

Corner/wall slim (corner luminar with lamp , reflec tor clear reeded acrylic cover Acrade make) as follws.


Line No


153 ACW/N -1 X 18W NOS 710

154 ACW/N -1 X 36W NOS 950

Decorative luminar with lamp reflector, opal/clear reeeded acrylic cover Arcade make as follows:

155 AMA-1 X 18W NOS 660

156 AMA-1 X 36W NOS 750

Philiphs Energy essential as follws

157 11 W NOS 230

158 14 W NOS 290

159 18 W NOS 320

160

Supply and fixing of spot light in sales room oppos ite to sales display shelving using Philiphs make Catalog 303-21 X 12 V , 50 W halogen Dichotic or equivalent inclusive of necessary conne ction , accessories , lamp etc.

NOS 1000

161

TELEPHONE SOCKET POINT : Supply and laying 2 pairs of 0.5 mm dia screened an d shielded telephone wire in 20 mm dia PVC conduit partly/full y concealed in all types of walls, floor etc. complete with all access ories, wiring terminations, connected civil works, rough plasteri ng etc. including supply of 16 GI fish wire conduit & accessories etc .

EA 11

Supply, fixing and commissioning of following pairs of telephone tag block of Krone type enclosed in suitable MS box. Ra te shall include all accessories, connected civil works for fixing the s ame as per specifications.

162 5 pairs NOS 70

163Supply and installation of modular type telephone s ocket MK make in a suitable size box concealed to wall including all civil works

NOS 400


Line no.


PART C :- EXTERNAL ELECTRIFICATION

164

Supply and fixing of wall mounting type meter board made out of 16 SWG CRCA sheet steel and single iron with 3 nos 200 A Fuse cutouts N.L , 1 no. earth link, 1 no. neutral link and spac e for accommodating 1 no. 3 ph, 4 wire KWH meter complete with adequate s ize of copper wire interconnections, powder coating etc. complete .

NO 2100

165

Supply, erection, testing and commissioning of floo r mounting type cubical panel board made out of 16 SWG CRCA sheet s teel with 300 A TPN copper bus bars, interconnections, earthing, po wder coating and comprising of the followings as required.(TYPE I AS PER ENCLOSED DRAWING): Incomer : 2 nos 125A TP switch fuse unit with HRC f uses for DG and EB with interlocking 1 no.125A TP bus coupler / 2 n os. volt meter with volt meter selector switch / 2 no. ammeter with CT & Ammeter selector switch / 2 sets of Phase indicating lamp (RYB) / Ou tgoings : 3 nos 63A and 6 nos 32A TP fuse switch unit with HRC fuse / 5 KVAR capacitor : 2 nos.

NO 31500

166

Supply, erection, testing and commissioning of floo r mounting type cubical panel board made out of 16 SWG CRCA sheet s teel with 200 A TPN copper bus bars, interconnections, earthing, po wder coating and comprising of the following as required. (TYPE II A S PER ENCLOSED DRAWING): Incomer : 2 nos. 125A TP switch fuse unit with HRC fuses for DG and EB / 125A 4 pole change over switch (on line) / 2 n o volt meter with volt meter selector switch / 2 no ammeter with CT & amm eter selector switch / 2 sets of Phase indicating lamp (RYB) / Ou tgoings : 2nos 63A and 3nos 32A TP fuse switch unit with HRC fuse/5 KV AR capacitor : 1 no

NO 43500

167

Same as above but with following details:- Incomer :2 nos 63A TP switch fuse unit with HRC fuses for DG and EB / 1no . 63A 4 pole change over switch (on line) / 2 no volt meter with volt meter selector switch / 2 no ammeter with CT & ammeter selector s witch / 2 sets of Phase indicating lamp (RYB) / Outgoings : 1 no 63A and 3 nos 32A TP fuse switch unit with HRC fuse, 5 KVAR capacitor : 1 no (TYPE III AS PER ENCLOSED DRAWING)

NO 50000

168Supply, installation and commissioning of 63A TPN M CB DB Incomer : 1 no 63 A , 4 Pole MCB Outgoings : 18 nos, 10A/16A /20A SP MCBs

NOS 5500

169Supply, installation and commissioning of 32A TPN M CB DB Incomer : 1 no 32 A , 4 Pole MCB Outgoings : 12 nos, 10A/16A/ 20A SP MCBs

NOS 4900

Supply and laying following size PVC insulated, sh eathed, armoured cable of approved make

170 3.5C X 35 sqmm AL cable RMT 200

171 4C X 16 sqmm AL cable RMT 145


Line no.


172 4C X 6 sqmm AL cable RMT 105

173 4C X 2.5 sqmm copper cable RMT 110

174 3C X 2.5 sqmm copper cable RMT 100

End termination of following cables with double com pression NFLP gland and crimping sockets

175 3.5C X 35 sqmm AL cable NO 190

176 4C X 16 sqmm AL cable NO 165

177 4C X 6 sqmm AL cable NO 115

178 4C X 2.5 sqmm copper cable NO 140


End termination of following cables with double com pression FLP gland and crimping sockets


YARD LIGHTING:

CABLE TRENCH:

181

Excavation in any type of soil including WBM / asph alt up to 600mm depth and 300mm wide including supply and laying 15 0mm thick sand on top and bottom of cable, supply and laying brick s laid flat on top, back filling trench etc. complete.

RMT 160

182 Junction box for yard light pole; NO 706

Supplying and fixing 150mm x150mm x125mm weather pr oof out door junction box fabricated out of 14 SWG CRCA sheet of IP 54 category of protection with rubber gasket and having locking ar rangement including required connector, 10A SPMCB.

Yard light pole:

183

Supply, Fabrication and Erection of 7 mtrs high gal vanised Pole having a base plate of size 300x300x16 with 1000 mm long 4 0mm MS pipe suitable for mounting 1 no. fixture as per attache d detail specificaton. Job also includes foundation for the same. Pole to be made up of 100mm dia MS pipe of 3.0 m length, 80mm dia MS pipe of 3.0m length and 50mm dia pipe of 1.0m length with 65mm dia cap, gusset plates, etc., complete.

NO 6500

184 Same as above but with double arm NO 7000

Street light fitting

185

Supply of street light fixture of WIPRO make cat n o. WST 65250 1 x 250W metal hallide lamp including lamp single piece die cast aluminium housing complete with all accessories, ch oke, acrylic cover etc. complete.

NO 5450


Line no.


186Providing and fixing MS angle / channel supports an d edge protection for trench etc. including providing hold fast, pain ting with two coats of red oxide primer and two coats of synthetic enamel etc.

KG 46

187

Providing pipe electrode pipe earthing as per IS 30 43 and attached drawing including excavation supplying 50mm dia GI pipe medium quality, filling the pit with alternate layers of c harcoal and salt, back filling, constructing chamber 400mmx400mx400mm inte rnal size with 100mm thick PCC 1:2:4, providing CI cover with fram e etc. complete.

NO 2203

188Supply and fixing 10 SWG copper wire for earthing c onnection to pumps, canopy columns etc.

KG 290

189 Supply and fixing 25x3 copper flat for earth con nection of panel KG 300

190Providing and fixing 6mm thick MS chequered plate i ncluding making holding arrangements, painting with two coats of r ed oxide primer and two coats of synthetic enamel paint etc.

KG 60

191 Supply and fixing 20mm thick ISI marked rubber m at. SQM 260


Line no.


PART D :- DRIVEWAY DEVELOPMENT

192

MURRUM FILLING : Supply and filling murrum in 200mm thick layers inc luding levelling with doser, watering, Compacting each layer with 8/ 10 MT road roller to obtain field dry density 92% of MDD, Dressing to p layer to the required slope, Testing of murum sample for OMC & M DD and testing of field dry density by core cutter for checking co mpaction. Payment will be made only for compacted thickness.

CUM 215

193

RUBBLE SOLING : Providing and laying dry trap rubble stone soling 2 30 mm thick including hand packing, filling the interstices wit h chips, spalls and binding with grit and selected murrum, watering, co macting by power rolling with 8/10 ton roller complete.

SQM 156

WATER BOUND MACADUM : Providing and laying WBM in layers of 75 mm compact ed thickness each using well graded stone aggregates of 40 mm to 63 mm size of approved quality. Rate includes spreading metals, h and packing, filling the interstices with spalls, chips, and approved qu ality binder and rolling each layer with 10 MT power roller with sim ultaneous watering till the metal is bound by the water binder paste t o achieve maximum compaction, finishing the surface to proper grade a nd level. Rate also to include carrying out the following tests on aggr egates and test result to be submitted to EIC before use and shall meet the following stength requirements. LA Abrasion value:40% ,Flakin ess Index : 15%.

194 First Layer 75 mm thick SQM 57

195 Second Layer 75 mm thick SQM 53

196 Third layer of 75mm thick using 53 to 22.2 mm si ze stone metal SQM 48

RCC DRIVEWAY :

197

Providing and laying 150mm thick RCC driveway with 1:1.5:3 nominal mix using 20mm and down size crushed stone aggregat es in panels using slotted MS channel shuttering, machine mixing , vibrating with screed board vibrator, pond curing for 14 days, vac cum dewatering, finished with power trowelling. Concreting shall be carried out as per IS 456.

CUM 3740

Rate shall also include providing approved quality polythene paper below the driveway, constructing horizontal and lon gitudinal vatas with 1:10 CM for curing, levelling depressions if a ny in the base with 20mm stone aggregates and stone dust.


Line no.


Proper slope to be provided in driveway for easy dr aining of rain water. Job shall include cutting grooves 4mm wide a nd 20mm deep by machine and filling the groove with polysulpide com pound, providing 12mm thick Shalitek board in the joints between pre cast cover of pipeline trench or top slab of U/G tank and RCC dri veway.

Testing of cube, reinforcement steel, stone aggreg ates, sand, cement etc. to be carried out by contractor at no extra c ost.Tubing, ducting, trenching and other necessary embedded items in con crete shall be checked with architect/HPCL representative before concreting.

The cement consumption for 1:1.5:3 mix shall be 410 kg/cum and compressive strength shall be 140 kg/sqcm and 230 k g/sqcm after 7 days and 28 days respectively. Rate shall be exclud ing reinforcement steel which shall be paid separately.

198Same as above but without vaccum dewatering and pow er trowelling with 1:1.5:3 nominal mix

CUM 3640

199

RCC PRECAST SLAB : Providing and laying RCC precast slabs of required size with 1:1.5:3 nominal mix using 20mm and down size crushed stone aggregates including shuttering, mixing, compacting, pond curi ng for 14 days etc. as per IS 456, transporting from the place of casti ng. Reinforcent steel shall be paid separately.

CUM 3600

200

STEEL REINFORCEMENT : Supply, fabrication and placing in position High yi eld strength deformed bars conforming to IS 1786 - Latest editio n grade FE 415 as required and directed at site for driveway includin g cutting, bending, placing in position and tying with 20 SWG binding w ire, complete. Quantity shall be measured as per reinforcement dra wing and with theoretical weights including all authorized laps. Unauthorized chairs, spacers and laps will not be measured and paid for. Reinforcement to be provided

MT 45000

201

ASPHALTING : Providing & laying 50 mm compacted thickness premix asphalt carpet and 12 mm thick seal coat (total compacted thicknes s 62 mm) on top of WBM surface as per procedure given below.

SQM 213

1) Applying a tack coat of hot 80/100 asphalt to it @ 5 kg for 10 sqm. for bitumenous surface and 10 Kg for 10 sqm. for no n bituminous surface after thorough cleaning of WBM surface.

2) Spreading a layer of premix at the rate specifi ed below in (a) and roll to full compaction with 10 MT roller to the re quired slope and compacted thickness of this layer shall be 50mm.

3) Spreading a layer of seal coat and rolling with 10 MT roller to the required slope and the total compacted thickness sh all be 62mm. Asphalt required for seal coat is 6.8 Kg for 10 sqm .


Line no.


a) Materials to be used per 10 sqm of 50 mm thick p remix asphalt carpet : 20mm stone metal: 0.34 cum 12mm stone met al : 0.17 cum. Asphalt 80/100 @ 2.5 KG

202

Surface preparation through cleaning of the exposed surface by wire brush to remove the loose sand, pebbles and any ino rganic material. Applying tack coat of 80/100 bitumen @ 9.5 Kg / 10 sqm, after surface preparation as per above. (Total compacted thicknes s of 112 mm) ( a) Providing 75 mm thick BT concrete using 1 Cum. of 4 0 mm hard broken granite metal (machine crushed) with 35 Kg. 80/100 grade bitumen and 0.13 CuM. of 12 mm hard broken granite aggregate for 10 Sqm. well mixed in machine mixer in correct proport ion including supply of material. Cost of machine mixer, power ro lling with 10 tonnes power roller and all labour charges etc., co mplete in all respect of stisfaction of H.P.C.L. (b) Providing 25 mm thick Black top surface using 0.27 CuM. of 12 mm hard broken granite chips (machine crushed) with 25.00 Kg. of 80/100 grade bitumen per 10 SqM. including cost of machine mixing, power rolling with 10 tonne s power roller and all labour charges etc., complete in all respect of satisfaction of H.P.C.L. (c) Providing 12 mm thick Black top seal coat using 0 .09 CuM. of 6 mm hard broken granite chips with 10 Kg. of 80/100 grade bitumen per 10 SqM. including sprinkling of sand over the black top, supply of material, machine mixing and rolling with 10 ton roller, lab our charges etc., to the satisfaction of H.P.C.L.

SQM 345

203

PAVER BLOCK : Providing and laying approved brand / make 80 mm th ick cement coloured paving blocks of M40 grade over a bed of 5 0 mm thick well compacted sand bed laid over well prepared sub base to the required line and level including all materials, labour, mac hinery, transportation etc., paving blocks should have chamfered top edges of not less than 4 mm and shall be laid and interlocked with a minim um of 2 mm gap which in turn packed with sand, compacting with pla te vibrator etc.complete. Edge restraint with RCC 1:1.5:3 will be paid separately.

SQM 470

204 SAME AS ABOVE WITH COLOURED PAVER BLOCKS SQM 525

HUME PIPE : Supplying, laying, joining and aligning following s ize NP3 class RCC Hume pipes conforming to IS-458 Latest Edition belo w approach road whereever directed. Rate to include joining with ce ment mortar, excavation up to required depth and providing and l aying PCC 1:2:4 haunching @ 1m C/C. Test certificates from manufact ure shall be submitted and approved by EIC before use.

205 300mm NB RMT 450

206 225mm NB RMT 390


Line no.


207 150mm NB RMT 310

INSPECTION CHAMBER : Providing and constructing following size inspectio n chambers with 230mm thick brick masonry in 1:5 cement mortar, exc avation, 75mm thick PCC 1:4:8 bed, plastering with neat cement fi nish, providing 12mm thick MS plate cover with 35X35X6 angle stiffn er and 50X50X6 angle frame etc. complete.

208 600mm X 600mm internal size X 700mm depth NO 4490

209 450mm X 450mm internal size X 700mm depth NO 4038


Line no.


PART E :TANK INSTALLATION AND PIPELINE

210

TRANSPORTATION OF TANK : Transportation of following capacity horizontal tan ks to outlet site including loading, unloading etc. complete. (m inimum 100 kms distance one way for each tank of capacity 22Kl /16Kl/9Kl). Only one way shall be paid.

NO 6000

211Additional mileage beyond 100 kms per tank. Only on e way shall be paid.

KM 24

212

EXCAVATION IN SOIL : Excavation for foundation upto 4m depth below exist ing ground level in any type of soil except hard rock. Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within / outside HPCL's premises to an unobjectionable place , as directed by the Engineer in Charge including spread ing, watering and compaction, complete.

CUM 110

EXCAVATION IN HARD ROCK : Discription same as item no. 212 except the soil wi ll be hard rock and excavation shall be done by chiselling.

213 upto 2 meter depth CUM 640

214 above 2 meter upto 4 meter depth CUM 915

215

PCC 1:4:8 : Providing and laying PCC 1:4:8 (1cement:4 coarse sa nd: 8 graded stone aggregate) with 40mm and dowm Size sto ne aggregates in foundation trenches, including comp acting, curing etc. complete.

CUM 1369

R.C.C. 1:1.5:3

Providing and laying RCC 1:1.5:3, providing steel o r plywood shuttering with proper supports, removal of form wo rk as per IS code, preparing mix using mechanical mixer, compact ing using mechanical vibrator, curing with potable water for 14 days etc. complete. Work shall be carried out as per IS 456 l atest edition. Rate shall be excluding reinforcement steel which w ill be paid separately vide item no 5.

216 Bottom raft CUM 3240

217Top slab (Rate shall be including providing Polythe ne paper below the slab, providing 12 mm thick shalicatek bo ard in jionts to separate pieces. Top slab to be cast in 4/3 piec es).

CUM 3460


Line no.


218

REINFORCEMENT STEEL WORKS : Supply, straightening, cutting, placing in position as per drawing, binding at every intersection with two st rands of annealed 20 gauge steel wire, HYSD bars Grade Fe-41 5 conforming to IS 1786.

MT 45000

TANK INSTALLATION : Installaion of HPCL supplied Tanks of following cap acity in earth pit / under driveway including lowering, pro viding holding down arrangement, Hydrostatic testing to pr essure of 3.5m water column, supplying & filling with water w ith necessary 50 mm dia pipe & on successful completion emptying out the water from tank, cleaning & drying the inner surfaces with cloth / cotton waste etc., doping wit h three coats of tank mastic paint of STP make and hot 30/40 bitu men (total doping thickness 3mm), fixing all fittings as requi red.

219 22 KL NO 10400

220 16 KL NO 9000

221 9 KL NO 8450

222

BRICK MASONRY : Providing 345mm thick brick wall with bricks having compressive strength of minimum 35 kg/sqcm in cemen t mortar 1:5 (1 cement: 5 coarse sand) in foundation and superstructure, plain or curved including providin g necessary scaffolding, raking the joints on both faces, curin g for 7 days etc. complete.

CUM 1825

223

SMOOTH CEMENT PLASTERING : Providing and laying smooth cement plaster of 15mm thick in single coat in 1:3 cement mortar mixed with water p roofing compound to interior walls including providing nece ssary scaffolding, curing etc. Complete.

SQM 100

224

SAND FILLING : Supply and filling coarse river sand in layers of 2 00mm thickness inside masonary pit / earth pit after tan k installation including watering, compaction etc. complete.

CUM 300

225

MANHOLE COVER : Supply, fabrication and fixing of manhole cover of size 900x900 mm with 65x65x6 angle frame and 16mm thick MS plate with 50x50x6 stiffener including painting with two coats of red oxide primer and two coats of synthetic enamel paint. The manhole cover to be fitted with providing and fixing 3mm th ick RAF Gasket packing (Champion make) of 750mm dia.

NO 8975

PUMP ISLAND AND INSTALLATION OF PUMPS

PUMP ISLAND


Line no.


226

Construction of pump island 1m wide with 230mm thic k brick masonry in CM 1:5, 12mm thick plastering in CM 1:4 roughened to receive granite tiles including excavation, 75mm thick PCC 1:4:8, sand filling and constructing the wall 300mm above the finished driveway level and 600mm below the finish ed driveway level .

RMT 1270

INSTALLATION OF DISPENSING PUMPS

Installation of MONO / DUAL / MPD pumps on pedestal including providing & fixing MS angle frame 65x65x6 & connecting suction pipe, electrical, earthing conne ctions to the pump. Job includes providing, fabricating and grout ing in proper level MS angle frame made out of 50 x 50 x 6 mm MS angles with holdfast etc. complete.

227 Installation of MONO / DUAL pumps NO 700

228 Installation of MPD pumps NO 2035

PIPE LINES

Supplying & Laying 'C' Class MS ERW black steel scr ewed pipeline conforming to IS:1239 (part I) – latest ed ition to the required slope & alignment with heavy duty MS fitti ngs like elbows, tees including doping pipe line with 1 Coat of red oxide primer and 3 coats of shalimastic HD THIXOTROPIC of STP cold applied anti corrosive treatment after prepari ng the surface as per manufacturer specifications.The join ts are to be made leak proof by using jointing materials like L itharge, Glycerin, Shellac, holdite. The pipes laid above gr ound shall be painted with two coats of synthetic enamal over two coat of zinc chromate primer of approved quality and shall be colour coded as per instruction of EIC. The pipeline shall be tested at a pressure of 5 kg/sqm.

229 40mm dia RMT 440

230 50mm dia RMT 490

231 80mm dia fill pipe RMT 647

ANGULAR CHECK VALVE : Supply and fixing ISI marked angular check valve o f Leader/GG make

232 40mm dia NO 1100

233 50mm dia NO 1275

FILL CAP & VENT HOOD

234Supply and fixing MS fill cap with locking arrangem ent including Godrej 6 lever brass lock

NO 395

235 Supply and fixing 40mm dia vent hood in vent pip e NO 390


Line no.


GRANITE WORKS

236

Providing and fixing 20 mm thick pre polished water cut black granite slab for pump island top including providin g 25mm thk bed cement mortar 1:5 (1 cement : 5 coarse sand), f loating cement slurry and finishing the joints with white c ement mixed with matching colour pigment.

SQM 2575

237

Providing and fixing 10 mm thick pre polished water cut black granite tiles for pump island dado including provid ing 12mm thk bed cement mortar 1:4 (1 cement : 4 coarse sand ), fixing the tiles with neat cement paste and finishing the join ts with white cement mixed with matching colour pigment.

SQM 1530

PIPELINE TRENCH

238

Providing pipeline trench as per drawing with inter nal size 300mm wide x 400mm depth including excavation, 100m m thick PCC 1:4:8, 230mm thick brick masonry in 1:5 CM, 12m m thick plastering inside in 1:4 CM, filling trench with sw eet river sand, 150mm thick RCC 1:1.5:3 cover with reinforcement 10 mm tor @ 125mm c/c both way as main steel and 8 mm tor ring as destribution, 50x50x6 angle edging, curing etc. com plete.

RMT 1290

239SAME AS ITEM NO 238 WITH INTERNAL SIZE OF 450MM WID E X 400MM DEPTH.

RMT 1700


Line no.


PART G : DISMANTLING WORKS

240Dismantling of existing pump island 1m wide and car ting away debris including removal of pump and disconnecting pipeline etc. complete.

RMT 345

241 Dismantling of existing building/structures CUM 5 25

242Dismantling of RCC roof, beam, column including ca rting away debris

CUM 70

243 Removal of AC sheet from roof and stacking as di rected by EIC SQM 32

244 Removal of structural steel and stacking as dire cted by EIC MT 3400

245Dismantling of brick masonry / PCC / RR masonry inc luding carting away debris

CUM 180

246Removal of MS / Aluminium doors / windows / fixe d glazing and stacking as directed by EIC.

SQM 70

247

Shifting of GEB / AEC Main, laisoning with AEC / GE B officials, including payment of all incidental charges etc., a ll complete ( Payment made to AEC / GEB shall be reimbursed to co ntractor by HPCL on submission of original receipt).

LS 900

248

Removing of existing ID sign carefully without dama ge and shifting the same or refixing the same at new place within the primises as per HPCL instructions. Job includes mak ing necessary electrical connecitons etc., complete.

NO 1850

249Removing the existing yard light poles including re moving of light fixtures carefully and with out damage and st acking at designated place as directed by HPCL.

NO 350

250Trimming the branches of trees above a minimum heig ht of 4m from ground level and carting away the same from th e site when and whenever required as per instruction of HPCL

Job 250

251Removing existing chainlink / barbed wire fencing i ncluding removing the grouted angles, rods etc., and stackin g the same carefully as directed.

RMT 18

252Breaking of RCC slab over tank and driveway by manu al means or by using pneumatic breaker and carting away the debris to unobjectionable place outside RO premises.

SQM 120

253Removal of existing paver blocks carefully and with out damage and refixing the same after the job completion in p roper line and level and compaction etc, complete.

SQM 35

Removing exiting dispensing pumps after disconnecti ng pipeline, electrical connection etc, and stacking c arefully as directed.

254 Single Pumps NO 460

255 Dual / 2T Mix Pumps NO 510


Line no.


256 MPD pumps NO 690

Laying of MS threaded pipeline to the required slop e of alignment with providing and fixing necessary MS he avy duty fittings like elbows, tees, including providing and applying doping the pipeline with shalimastic HD 2 coats.

257 40 mm dia pipeline RMT 330

258 50 mm dia pipeline. RMT 390

259 80 mm dia piipeline. RMT 620


Line no.


PART H : CLUB HP WORKS

260Installing Club HP Signage Board with necessary CC 1:2:4 foundation upto required depth. Job also supply 4 n os. of 12mm dia x 750mm long MS foundation bolts etc, complete.

NO 2050

261Installing Air Tower facility with necessary CC 1:2 :4 foundation of required size and also with necessary electrical connection.

NO 1250

262Positioning of Q & Q Tower Board to shown place wit h necessary foundation.

LS 1700

263Fixing of water cooler with necessary electrical co nnections of 5/15 Amp switch board with necessary wiring.

NO 950

264Providing and painting work for Quick Care Point as per standard design.

JOB 800

265Installing Ingress and Egress Signage Board with ne cessary CC 1:2:4 foundation and with necessary electrical conn ection.

NO 1000

266Installing Credit Card Counter with providing and m aking electrical connections of 5 Amp Switch socket and t elephone socket connection with necessary wiring.

NO 1300

267 PROVIDING AND FIXING 930 PROF GI PERFORATED SHEET SMT 650

268

SUPPLY AND LAYING GRANULAR SUB BASE: Filling materi al with GSB (Granular Sub Base) of 60 cm thick: The GS B shall consists of the following material 40 to 53MM size metal : 40% 20 to 40MM size metal 20% 10 to 20MM size metal 20% 0 to 10MM size metal 20% Job shall include supply and filling GSB materials in two compacted layers of 300MM each. Payment shall be re leased on the compacted layer provided by the vendor at site. Compaction shall be carriedout only with Vibro roller of requi red capacity. Contractor has to obtain necessary clerance from HP CL or its autorised reprensatative for first layer. Only afte r obtaining the second layer GSB shall be provided. Job includes al l material and transporation cost of the required to be comple ted as per the directions of the HPCL

CUM 700

Line no. Description UnitUnit Rate

269

Filling in ground, plinth and surrounding areas wit h good yellow earth (quality shall be approved by engineer) brou ght from outside in layers of 15 to 20 cms including watering, conso lidating the same complete as directed. The filling shall be don e strictly in layers and the same shall be compacted and sprinkli ng of water shall be done simultaneously to get the compacted s urface in required gradient. The contractor has to get the so il sample approved from the site engineer, and required testi ng also shall be done, no extra charges will be given for that.

CUM 130

270Providing Garden Soil and Farm Yard Manure, mixing same in the proporaiton of 3:1 (by volume) and filling in the Panter wiht this mixture as per plan.

CUM 240

Providing and Laying 60mm THK (Compacted Thickness) Premix asphlt carpet on top of WBM or Compacted Surface. R ate to inclde Cleaning the Existing surface with wire brush to re move excess surface materials, rolling the existing surface to receive carpert, providing and spreading tack coat wiht asphalt of 60/70 OR 80/100 OR Equivalent grade dependingon site conditions and approved by EIC @ 9.8 Kg/10Sqm, Premixing the aggregates of spe cified grading as detailed in the specifications with hot molten asphalt in Mixers, laying on top of WBM surface using mechanic al mixers or mixers arrangement approved by EIC depending on Qty to be executed at a perticular site. The rate ATEI Includ e rolling with 10Mt Roller till Maximum Compaction is Acheived, Te sting the surface for camber if Required, Correcting Depressi ons with additional fresh mix and rerolling as per specifica tions. providing 20mm Thick seal coat on top of asphalt carpet immed iately rolling to full compaction. rate to include premixing the a ggregates (6mm cown sized/coarse sand) wiht pre-heated asphalt ( 8 0Kg/CUM) In mechanical mixera and ,

Spreading & Rolling to acheive Maximum Compaction a s per attached specs. Rate analysis also to include provi ding of quary dust/sand (As Approved by EIC) After Completion of seal coat. The combined thickness of asphalt carpet & seal coat sh all be minimym 80mm. Compact thickness of asphalt carpet s hall be minimum 60mm in case seal coat is not layed immedia tely over the asphalt carpet, Tack coat @ 6Kg/10Sqm of carpet are a with asphalt of grade as specified above shall be Spread before laying seat coat.

272

Supply of precast RCC Kerbing blocks of various sha pes in PCC 1:2:4 of size 18" Height, 6" Thickness and 12" wide including installing the same in ground. The rate includes ex cavation up to 6" Deep and 6" wide Compacting the base and 75mm PC C 1:4:8 & Installation by joining Pointing it with cement mix 1:3 If Required back Filling Excavated stuff with wo coats of appro ved oil dispemper etc complete as per satisf action of EIC.

RMT 1500

271 SMT 280



273Providing and planting mexican lawn type - Ready ma de grass in area alongwith top soil filling of 150mm with manur e good earth etc or as per direction of EIC.

SMT 500

274Supplying and fixing mehendi red 150mm height plant in area as per layout and instruction of EIC. Including wateri ng etc complete till the plant has survived.

NO 20



275Supplying and fixing mehendi golden 100mm height pl ant in area as per layout and instruction of EIC. Including wat ering etc complete till the plant has survived.

NO 20

276Supplying and fixing mehendi bitter (Green Hedge Ty pe) type of 150mm Plant in area as per layout and instruction o f EIC. Including watering etc complete till the plant has survived.

NO 15

277

Providing and fixing prefabricated 500mm High crash barrior in tubes 2mm THK outside pump island, at both side end s of island with grouting in CC 1:2:4 size and 450X450X300mm & including transportation etc complete. ( The details to be so ught as per new format island). Note party to quote rate for only o ne side of Island.

NO 9000

278

SUPPLY AND LAYING POLISHED KOTA STONE 550 mmx 550 mm : Providing and fixing 20 mm thick one piece Kota sto ne slabs with 25mm bedding CM 1:3, cement slurry and machine po lishing on one side for risers of steps, treads and shelf slab including nosing etc. complete.

SMT 700

279

POLISHED VITRIFIED TILES (600mmx600mm) SALT PEPPER GREY FROM MARBONITE:Providing and laying polished vitrified Ceramic til es of above sizes on flooring (approved make & shade, free from crack s, warpage, fissures and flakes, straight edges and perfect cor ner).600mmx600mm of marbonite brand

SMT 1800

280

POLISHED VITRIFIED CERAMIC TILES (900MMx900MM) SNOW CARARA FROM MARBONITE :Providing and laying polished vitrified Ceramic til es of followg sizes on flooring (approved make & shade, free from cracks, warpage, fissures and flakes, straight edges and pe rfect corner). 900mmx900mm SNOW CARARA of MARBONITE brand.

SMT 2200

281

POLISHED VITRIFIED TILES (600MMx600MM) FROM MARBONITE :Providing and laying 1st quality polished vitrified ceramic tiles of 8 mm thick of followg sizes on flooring (approved mak e & shade, free from cracks, warpage, fissures and flakes, str aight edges and perfect corner).600mmx600mm of MARBONITE brand.

SMT 1500



282

POLISHED VITRIFIED CERAMIC TILES (600MMx600MM) OLYMPUS FROM MARBONITE :Providing and laying 1st quality polished vitrified TILES on flooring (approved make & shade, free from cracks, warpage, fissures and flakes, straight edges and perfect corner).600mmx600mm of MARBONITE, OLYMPUS.

SMT 1600



283

S&L ACRYLIC DISTEMPER FOR CEILING (ASAIN PAINTS/ BERGER) : Providing and applying 2 coats ( first coat with br ush and final coat with Roller) of ACRYLIC DISTEMPER of approved make and shade on all surfaces and heights to give an even shade i ncluding priming coat and full putty.

SMT 65

284

Supply and fixing mineral fibre grid false ceiling of armstrong make as per manufactururer's recommendation.

SMT 950

285

SUPPLY AND LAYING ECONOMY EMULSION PAINT (ASIAN/BERGER/ICI).Providing and applying 2 coats ( first coat with br ush and final coat with Roller) of ECONOMY EMULSION PAINT of appr oved make and shade on all surfaces and heights to give an even shade including priming coat and full putty.

SMT 65

286

S&L EXTERIOR ACRYLIC EMULSION (WHITE) PAINT - ASIAN/BERGER/ICIProviding and applying 2 coats (first coat with bru sh and final coat with Roller) of ACRYLIC EMULSION (WHITE) of approve d make and shade on all surfaces and heights to give an even s hade including priming coat and full putty.

SMT 85

287Supply and Laying 600MM x 300 MM Wakk glazed Tiles of Approved Make (Johnson -Riveira).

SMT 920

288Supplying and Laying External Mosaic chequred Tiles of Size 300mm x 300 mm (Red & Gray Combination With 20mm TH K Cement Mortar. Make of Nitco - RY36S, GY 36S.

SMT 480

289

PLAIN CEMENT CONCRETE: Providing and laying PCC of following mix includin g providing and fixing form work, machine mixing, compaction and cu ring etc complete as per specification.PCC 1:3:6 mix using 20 mm and down size graded cru shed aggregates below flooring, plinth protection etc.

CUM 1800


Line no. Description Unit Unit Rate

290

BRICK MASONARY - 230 MM THICK IN 1:4 CM FOR KERBING : Providing and constructing brick masonry in CM 1:4 using bricks having minimum compressive strength 35 Kg/cm 2 and conforming to IS: 1077- Latest Edition including pr oviding all openings and projections.

CUM 1850

291

18-20MM THICK GRANITE SLAB :Providing and fixing machine cut and polished spott ed grey or black Granite slab of thickness of 18-20 mm selecte d & sorted for uniformity in colour.

SMT 4000

292

EARTH FILLING YELLOW : Supplying and filling good quality yellow earth in layers of 150 mm thick including watering and compacting till max imum compaction is achieved as directed by Engineer In C harge.

CUM 150

293Supply and fixing as per manufacturer's specificati on vitrified ocean mist tiles of 1m X 1m of NITCO make.

SMT 2050

294Supply and painting yellow thermoplastic road marki ng paints of approved make at asphalted / pavered and RCC Dri veways with HPCL approved symbols signages and letterings.

SMT 950

295

Supply & Fixing rolling shutter in enamel paint,1.2 mm THK MS Sheet slats as per approved DRG enclosed. SMT 2000

296

Supply, fabrication and fixing staircase railing wi th polished stainless steel pipe at two levels of 40mm & 30mm w ith SS plate balusters with 4 row of 12mm DIA steel tubes (detai ls as per drawings) of any SS structure as per drawing suppli ed by HPCL like island guard etc. Stainless Steel should be of best grade i.e 304 grade.

KG 560

297

Supply and fixing deep blue powder coated, extruded aluminium section frames with clear glass / prelaminated part icle board infill paneles, glass should be of modi / saint gob ain and all sections to be of jindal make. ( Refer DRG Enclosed for more details).

SMT 3500

298

Providing and fixing Al fixed glazing as per format drawing enclosed. Glazing frame should be poweder coated wi th HP blue.

SMT 3900

299 SUPPLY AND FIXING DOOR SPRING OF EVERITE / HARDW YN. NO 1500

300SUPPLY AND FIXING OF DOOR CLOSER OF HARDWYN / EVERITE MAKE. NO 1200



301

Providing & Fixing under ground / open 100 mm dia P VC pipe for Rain water line, conduit, cabling, draingange e tc. as per details including necessary specials, fixing the cl amps & applying approved paint. The pipes shall be of Prin ce / kissan or equivalent ISI make including fixing the jonts with pidilite/ Aralidate type sealent complete.

RMT 200

302

Providing & fixing under ground / open PVC pipe 75m m dia. PVC pipe for Rain water line, conduit, cabling, dra inage etc. as per details including necessary specials, fixing th e clamps & applying approved paint. The pipes shall be of Prin ce / Kishan or equivalent ISI make including fixing the joints with pidilite/ Araldite type sealant complete.

RMT 170

303

Providing and fixing 40 mm dia PVC pipe of 6 kg/sq cm of PRINCE / SUPREME or approved make for rain water / sewage with all necessary fitting like bend, coupling, tee etc.

RMT 120

304

Provding and fixing cast iron floor trap Heavy Duty of self cleansing design conforming to IS specs with 100mm inlet, 75mm outlet and 150mm CP hinged grating of 6mm thic k with rim. Rate shall include making all necessary leak proof connections etc.

NO 100

305

Supplying and laying the following cast iron socket and spigot end pipes including plain or plug type bends, shoes , offsets, clamps junctions, tees, etc caulking of joints with lead, smoke testing the pipeline before commissioning and apply ing 3 coats of black enamel paint over a coat of primer after n ecessary surface preparation complete.100 mm dia soil down take pipes upto gully trap wit h 45 mm deep joint as per IS 1729 - 1979.

RMT 150

306

Supplying and laying the following cast iron socket and spigot end pipes including plain or plug type bends, shoes , offsets, clamps junctions, tees, etc, caulking of joints wit h lead, smoke testing the pipeline before commissioning and apply ing 3 coats of black enamel paint over a coat of primer after n ecessary surface preparation complete.150 mm dia soil down take pipes upto gully trap wit h 45 mm deep joint as per IS 1729 - 1979.

RMT 210

307

Supplying and fixing in position 225mm x 150mm (9 x 6) S.W. Gully Trap, make of jaguar-Continental in brick mas onary chamber of required size with C.I. Covers and frame s of approved quality (Heavy Duty 100 kg.) including exc avations and back filling, cement concrete 1:3:6 in foundati on and bed in brick masonry in CM 1:2,Plastering 20mm with CM 1:1 finished with a neat coat of cement etc. complete as per HPC L specifications and Architects instructions.

NO 500



308

Providing and constructing inspection chamber as g iven below & as per the enclosed sketch.900 x 900 mm (Internal dimensions) with 750 mm dept h for main chamber with top RCC slab in 1:1.5:3 mix, excavati on, BBCC/PCC wherever required & floor concrete 1:3:6 m ix. complete as per drawing .The inside walls should be duly plastered with 15mm cement slurry & channels made i n cement concrete in 1:2:4 mix, with CI frame & cover weighi ng 125 kg confirming to IS 1726-1974 pattern-2 (Part VI/Sec I ), curing testing, complete.

NO 5000

309

Providing and constructing inspection chamber as gi ven below & as per the enclosed sketch.600mm x 600 mm (clear Internal dimensions) with 600 mm depth with brick masonry 230mm thick wall inside & top fi nish plaster with necessary excavation, B.B.C.C. etc. complete f or outlets of all water closets and at all bends in the sewerage pipes with CI frame & cover weighing 125 kg confirming to IS 1726 -1974 pattern-2 (Part VI/Sec I).

NO 3500

310Supply and fixing WC Orrisa pan with low level cist ern. WC-0109/17, CISTERN-0709 PARRYWARE, 20028 HINDWARE. NO 6 000

311

SUPLY AND FIXING URINAL: Flat back large with auto flush of 0575 new magnum: PARRYWARE 60006 - OLYMPUS.

NO 9000

312

SUPPLY AND FITTING COUNTER TAP WASH BASIN : Oval below counter basin 5500418 Parryware/10016 Ov al Hindware with sensor Tap (Faucet) 51071 Sensor - Ja guar with complete accessories etc complete.

NO 10000

313

Supplying and laying underground 15mm dia G.I. "B" Class pipe lines of TATA / Zenith / Jindal or equivalent appro ved ISI make only for water connections including supplying and fixing of all special fittings and fixtures like elbows, bends, t ees, reducers, coupling and threading including excavation upto 60 0 deep, back filling of trenches and making good the damage d surface for underground pipes and fixing pipeline with suit able G.I. clamps, making water tight threading joints back fi lling of trenches, consolidating, watering etc. including pa inting above ground P/L with 3 coats of aluminium / synthetic en amel paint as per HPC specifications and Architects instructio ns.

RMT 225



314


RMT 270

315


RMT 470

316Supply & fixing fullway valve of 15mm dia for GI pi peline of GG / LEADER make. NO 800



319

Providing and fixing bevelled edge mirror of superi or glass of 5/6 mm thick of MODI GUARD GLASS make, 3mm thick fe lt backing over 8mm water proof ply KITPLY/ANCHOR or equivalent make and with wooden beading allround of 600 X 600 size and fixed with wooden plugs with CP brass scre ws and cup washers etc. all complete as directed by Engineer I n Charge.

SFT 250



320Supply & Fixing towel rings - CP ring mounted on wa ll of 1576 Classic Line- Parko.

NO 300

321

Supplying and filling good quality Yellow/ Red Murr um in layers including watering and compacting till maximum comp action is achieved as directed by engineer in charge. The spe cification meeting to the latest standards of IS code.

CUM 200

322

Providing and constructing brick masonry in CM 1:4 using bricks having compressive strength 35 Kg/cm2 and conformin g to IS: 1077- Latest Edition including providing all openin gs and projections as per the drawing, raking the joints t o 1 cm deep, scaffolding, soaking of bricks prior to use and cur ing etc complete as per specifications.230 mm & above thickness in walls / foundations etc .

CUM 1750

323

Providing and laying average 20 mm thick sand faced cement plaster as per following procedure :Apply 12 mm thick coat of CM 1:4 mixed with CICO/ I MPERMO/ ACCOPROOF water proofing compound mixed as per manufacturer's specifications as 1st coat and leavi ng the surface rough. Apply 2nd coat of 8 mm thick of CM 1:4 and f inishing the surface by rubbing with sponge till uniform texture is obtained. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of brick and concrete surfaces, with a minimum overlap of 150 mm in all directions and curing comp lete.

SMT 145

324

Providing and laying following thick cement plaster ing in single coat to all the interior walls / ceiling including scaffolding, chicken wire mesh at all joints of brick and concre te required to achieve perfect line and level. 12mm thick plasteri ng in CM 1:4 for walls with NEERU/LIME finish.

SMT 130

325

Supplying fixing AC corrugated sheet of "Charminar or Everest"or approved make for roofing including supply of 'J' b olts and 75 mm MS Pipe with red oxide paint and bitumen and GI wa shers etc. complete.

SMT 250

326Providing and fixing AL coloured sheet for roofing of Track Make of 1-1.5mm thickness.

SMT 1250

327Supply and fixing structural steel work with Pipe r ailing and Baluster as per DRG enclosed.

KG 51

328Supplyand fixing conventional mangalore tiles for s loping and Chajja.

SMT 700

329Supply and fixing tube light mirror optic of 2 X 36 w of PHLIPS- TBS300 / 418 M1, WIPRO- CAT NO. WCF93418NS or cromp ton- CAT NO. CRFN 42 HSB.

NO 1900

330Supply and fixing with complete fixtures 1X36W Box Type fitting Luminaries of WIPRO CAT NO.14140, PHILIPS-CAT NO. T MC 501/136 or CAT NO. DJB 14 of Crompton.

NO 500



331providing and fixing 1 x13W CFL down light with com plete fixtures of WIPRO / PHILIPS or CROMPTON make

NO 1750



332

Providing of cable trench by excavation in any type of soil including WBM/ Asphalt upto 450mm depth and 300mm w ide including supply and laying of 150mm thick sand top and bottom of cable, supply and laying bricks laid flat on top , backfilling trench etc. complete.

RMT 700

333

Providing and laying PVC armored cable of CI, ASIAN , Trapdoor (Seimens) or equivalent make confirming to IS: 1554 (part-1) 1976 for power/light wiring and providing necessary conn ections as directed A) 4x4 core Copper cable.

RMT 140

334

Providing and laying RCC 1:1.5:3 concrete for works using 20 mm and down size graded crushed aggregate including pr oviding and fixing necessary shuttering, scaffolding, machine m ixing, compacting by mechanical vibrators, curing etc com plete. Concrete shall conform to IS 456-Latest edition. Ra te shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item.

CUM 3800

335

Supply/ Fabricating & Construction of Electrode Typ e Earting Pit as per IS 3043 and Electrode with Typical Earthing chamber including PCC Chamber, cast Iron cover, and 600X600 CU Plate & 40mm GI Pipe with funnel / mesh and two runs of 40X 6mm CU Strip as per drawing enclosed in " Appendix-5 compl ete. The cost includes excavation / charcoal / sand etc complete. The clamping arrangenent shall be done by proper NUT BOLTS / WAS HERS etc complete. Note all scope as shown in the appendix-5 (Enclosed) Should be kept in mind the earthing chambers, cover s etc all should be included in the rates. Please ref\er draw ing No. Appendix-5 Enclosed.

NO 9000

336Providing and fixing 75mm dia `B' CLASS GI pipes wi th plugs, nipples, unions, etc including all acessories. The pipes should be buried underground in trenches etc complete

RMT 680

337Providing and fixing 60mm dia `B' CLASS GI pipes wi th plugs, nipples, unions etc including all acessories. The p ipes should be buried underground in trenches etc complete

RMT 560

338Providing and fixing 100mm dia `B' CLASS GI pipes w ith plugs, nipples, unions, etc including all acessories. The pipes should be buried underground in trenches etc complete

RMT 780

339

Providing and laying RCC 1:2:4 concrete for works u sing 20 mm and down size graded crushed aggregate including pr oviding and fixing necessary shuttering, scaffolding, machine m ixing, compacting by mechanical vibrators, curing, etc. c omplete. Concrete shall conform to IS 456-Latest edition. Ra te shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item.

CUM 2960



340

Supplying and fixing in position 7M meter height Ba jaj Make Octagonal Yard light poles of single arm including 3 wires x 2.5 sq.mm copper wire from fuse cut out to luminaire an d 8 SWG coil earthing with salt & coal for each pole. The rate s hall include light fixture suitable for 250 Watt metal halide light la mp of "phillips/ crompton / wipro" make includding supplying of cond enser, ballast, igniter and cost of lamp also. ( Excluding Foundation)

NO 18500

341

Supplying and fixing in position 7M meter height Ba jaj Make Octagonal Yard light poles of double arm including 3 wires x 2.5 sq.mm copper wire from fuse cut out to luminaire an d 8 SWG coil earthing with salt & coal for each pole. The rate s hall include light fixture suitable for 250 Watt metal halide light la mp of "phillips/ crompton/wipro" make includding supplying of conden ser, ballast, igniter and cost of lamp also.

NO 24000

342

Supplying & erection of fire buckets with covers fi lled with good quality sand with stands of angle frames of the sam e at appropriate place. Rate to include painting with 2 coats of red oxide primer and 2 coats of enamel paint of approve d make and shade. The stand should be 1.5 mtrs. height fabrica ted with 50x50x6 angles with required shading arrangements o n top of buckets with 18 guage MS sheet on 25x25x4 MS angles (each stand to have four buckets).

NO 5500

343Supply & Fixing / Grouting of MS foundation J bolts for foundation in RCC. Job includes supply of J bolts & check nuts .

KG 55

344

Exhuming 22 kl tank from earth / masonry pit. The j ob includes taking out the balance product from tank, opening n ut bolts from raft, excavation / clearing the sand/soil & lifting under ground tank from RCC / Earth pit by crane only and loading the same at cariier / truck or storing safely at places as drected by E IC. All tool tackles, machinary crane labour etc will be borne b y the party

NO 10000

345

Exhuming 16/14 kl tank from earth / masonry pit. Th e job includes taking out the balance product from tank, opening n ut bolts from raft, excavation /clearing the sand/soil & lifting under ground tank from RCC / Earth pit by crane only and loading the same at carrier / truck or storing safely at places as drected by E IC. All tool tackles, machinary crane labour etc will be borne b y the party

NO 9500

346Supply of DCP (B&C) type 10 kgs. Fire extinguishers as per ISI specifications and ISO 9002 certified company of ap proved make like Minimax, Firex, Bharat, Safex with complete ac cessories.

NO 1850

347

Supply of CO2 type 4.5 kgs. Fire extinguishers as p er ISI & CCE approved and specifications and ISO 9002 certified company of approved make like Minimax, Firex, Bharat, Safex wi th complete accessories.

NO 4500



348Providing, spreading and rolling 10mm black grit ( black basaltic rock) on the drive way with consolidate thickness o f 25mm.

SMT 35

349Supply and Fixing 1" X 5mm thick copper braided str ip of IS quality / make and clamping the same with earthing grid and earthing clip of as advised by EIC complete

RMT 235

350

Supply and Fixing ISI Mark crocodile CLIP Including Fixing / Connecting the same with braided STRIP/WIRE. The cr ocodile clip should have CU / BRASS connecting point and should be of ISI mark.

NO 100

351

Supply and fixing fill cap of cast iron having clam p /stud for earthing arrangement with BIS threading suitable ma le - female coupling with unloading hose. The fill cap shall ha ve cast iron cap with locking arrangement and earthing clamp/stud to facilitate fixing of CU braided strip.

NO 700

352Supply and installation of 1HP Kirloskar make subme rsible water motor pumpset including fitting of switch/STARTER/C ABLE/panel at electrical room within 25 RMT distance.

NO 9500

353

Installation of air tower in RCC foundation OF 1:2: 4 (0.5 m wide and 1 m long) of 100m height from FGL and 150mm bel ow FGL with excavation supply & grouting of necessary nut foundation / bolting ( included in rate) of base frame etc compl ete in all respects. The job includes base plaster 12mm thk of CEMENT RATIO 1:4 & fixing granite tiles of 10mm thick as p er standard procedure.

NO 2500

354

Supply, transportaion & laying of prefabricated FI BRE REINFORCEMENT CONCRETE trench cover of size 600mm x 450mm and 100 thickness of M30 grade including tran sporation, laying etc complete. The rate includes supply and f ixing of 18 guage MS sheet on periphery of trench cover etc com plete including providing of hooks made with 12mm thick reinforcement steel bar by moulding the bar.

NO 700

355

Installation of Master pole with Logo Box. The scop e includes installing the same by crane, supply and fixing 6"x 6" single choke Sintex make Junction box, supply of 2.5 sqmm. 3 cor e cable of polycab / mecab / Finolex / Avocab / Procab / Power cab make from JB to logo box including testing electrical sy stem and commissioning the same etc complete.

NO 3200

356

Installation of Grand ID Signage post. The scope in cludes installing the same at existing foundation by crane including end termination of cables from the point, testing the l ights / electrical connection and commissioning the same etc complete.

NO 8500



357

Installing Curtain wall Logo Box with Logo. The sco pe includes fixing the same in the curtain wall gap / depressio n, sealing the gap by cement slurry and matching it with granite, carrying out electrical connection of cable from nearest point a nd testing the same and commissioning etc complete.

NO 600

358

Installing Q&Q tower at site. The job includes inst alling the same at existing foundation with providing 4 nos of anch or fastners with bolts etc complete the fastner and bolts shoul d be included in rates.

NO 750

359Supply & Fixing 6 Amp or 16 Amp DP MCB of indokopp Gold / Legrend Make at existing panel or wall or as direct ed by EIC.

NO 245

360Supply and fixing SINTEX make single choke outdoor junction box. Including fixing the same at post or places as directed by EIC.

NO 750

361Supply and fixing SINTEX make Double choke outdoor junction box. Including fixing the same at post or places as directed by EIC.

NO 1400

362Supply and fixing cable jointing kit of Araldite ma ke to cables of 4 CORE 2.5 SQMM cable at places as directed by EIC.

NO 1900



363 TPT OF D/Us UPTO 100 KMS NO

Transportation of Dispensing Unit / Master pole/ Curtain Wa ll Logo / AirTower / Q&Q Tower / Club HP Pole / Yard Lght Pole / Air Compresso r / CityPylon from storage point to various Retail Outlets includin g loading andunloading at both ends.

364 TPT OF D/Us 101 TO 200 KMS NO

Transportation of Dispensing Unit / Master pole / Curtain Wa ll Logo / AirTower / Q&Q Tower / Club HP Pole / Yard Lght Pole / Air Compresso r / CityPylon from storage point to various Retail Outlets includin g loading andunloading at both ends.

365 TPT OF D/Us 201 TO 300 KMS NO

Transportation of Dispensing Unit / Master pole / Curtain Wa ll Logo / AirTower / Q&Q Tower / Club HP Pole / Yard Lght Pole / Air Compresso r / CityPylon from storage point to various Retail Outlets includin g loading andunloading at both ends.

366 TPT OF EXISTING MS HOARDING 0 TO 10 TON WEIGHT UPTO 100 KM. MT

TPT of existing MS Hoarding board including loading & Unload ing at bothends carefully.

367 TPT OF EXISTING MS HOARDING 0 TO 10 TON WEIGHT 101 TO 250 KM. MT

TPT of existing MS Hoarding board including loading & Unload ing at bothends carefully.

368 REMOVAL OF EXISTING MS HOARDING UPTO 5 TON. WEIGHT MT

Removing of existing Hoarding Board with removing of electr ical connection& fixtures. Job also including of put the material at safe place.

369 REM OF EXISTING MS HOARDING 5 TO 10 TON. WEIGHT MT

Removing Of Existing Hoarding Board with Removing of Electr icalConnection & Fixtures. Job also including of put th e material at safe place.

370 ERECTION OF HOARDING BOARD UPTO 5 TON WEIGHT MT

Erection of supplied Hoarding Board with necessary bolting and minorreparing work completed.

371 ERECTION OF HOARDING BOARD 5 TO 10 TON WEIGHT MT

Erection of supplied Hoarding Board with necessary bolting and minorreparing work completed.

372 HOARDING PAINTING - ARTISTIC SQM

Painting of MS Hoarding : Painting of MS Hoarding as per messa ge (ARTWORK) given by HPCL at various Outlets under Region. Job Incl udes surfacepreparation, applying two coats of synthetic enemel paint o f approve make.Job also inludes providing scaffoldings / tool tack les etc complete.

2200

120

2800

2400

3500

3000

3800

4500

1700

2200



373 S&F G.I. SHEET ON HOARDINGS SQM

Supplying and Fixing of 22 gauge GI Sheet on Hoardings Board s tructure byAlluminium Reverting arrangement of size 20mm long and 6mm d ia asshown In the Drg. Job also includes painting of GI sheet with 2 coats of RedOxide. Job includes scaffoldings / tools / tackels etc complete.

374S&L. OF PRECAST FRC TRENCH COVER W/O MS SHEET

CUM

Supply & Laying of precast 150mm thk. RCC trench cover in M30 C ementConcrete grade with 12mm dia TMT reinforcement steel bar in 1 00mm c/cboth way job also including of laying of cover on pipeline tre nch in line andlevel completed.

375 S&F 150 WATT METAL HALIDE NO

S&F 150 watts MH Light fixtures on the Hoarding of WIPRO/BAJA J/PHILIPSmake suitable for outdoor use with prior approval of HPCL and complete inall respects. Job insludes clamping arrangement for light t o focus on theHoarding.

376 S&F NFLP JUNCTION BOX NO

Supplying and fixing NFLP Junction box of size 6"X4" Sintex B ox NFLPglands for lighting.

377 S&F 16 AMP DP MCB SWITCH NO

Supply and fixing of 16 Amp MCB DP Switch of " INDOKUPP" LEGARN D,HAGER -L&T Brands ISI make in distrubition board or if requir ed PVC covercompleted with switch.

378 P&L OF 1.5 SQMM 3 CORE FLEXIBLE CABLE RMT

P&L of 1.5 SQ.MM 3 Core flexible cable in 1.5sqmm dia screened andshielded wire in 20mm dia PVC conduit partly / fully conceale d in types ofwalls, floor etc. complete with all accessories, wiring ter minations,connected Civil works , rough plastering etc.

379 P&L OF 2 PAIR TELEPHONE WIRE RMT

Providing and Laying 2 Pair of 0.5mm Dia screened and shielde d Telephonewire in 20mm dia PVC conduit partly / fully concealed in all ty pes of walls,floor etc complete with all accessories, wiring terminatio ns, connected Civilworks , rough plastering etc including tools tackles clamps pins etccomplete.

380 P&F OF 63 AMP CHANGE OVER SWITCH NO

Supply and installation of 63 AMP Change Over Switch in sheet steelenclosure suitable for wall mounting with necessary access ories and fixingitems. " KEW & L&T" brand ISI make.

381 P&F OF CASSING CAPPING PATTI RMT

P& F of cassing capping patti of required size for open wiring in side salesbuilding with line and level completed.

382 P&F OF ELECTRONICS TYPE ELECTRICAL TUBE LIGHT/ CHOK E NO

500

4500

5300

400

575

55

18

4500

32



Providing & Fixing of Tube Light with electronick Chock of 'P hilips' &'Crompton' make in Grand ID Tower and curtain wall logo box.

350



383 P&F OF 40 AMP. ELCB NO

Providing & Fixing of 40 Amp ELCB 4 pole switch of " INDOKUPP /LEGARND / HAGER / L&T Brand ISI Make

384 P&L OF 25MM DIA FLEXIBLE PVC CONDUIT PIPE RMT

P&L of 25mm dia flexible PVC conduit pipe for conducting of wi re fordistribution board MCB switch cable laying.

385 P&L OF TWO WAY POINT WIRING NO

Providing and Laying of Point Wiring in concealed conduits f or the followingpoints using specified grade PVC insulated, ERLS multistra nded 3X1.5Sqmm copper wire. Job also including of preparation of wall i n plasteringwork completed.

386 PAINTING OF AIR TOWER & Q&Q TOWER NO

P&A of 2 coats of synthetic enamel paint 1st quality of approv edmanufacturer and shades on steel srface to give an even shade includingtwo coats of red oxide primer after thoroughly brus h.

387 EXHUMING OF 9/11 KL TANK NO

Degassing exhuming tank from the Pit including excavation e tc. Job coversdismantling all fittings and piping etc. Job also includes r emoval of products& store in safe place as advised by HPCL's represen tative (9/11KL tank)

388 BM EARTHING CHAMBER NO

Providing and constructing earthing inspection chamber of 450X450mm(internal dimensions) with 4450 mm chamber and medium duty r ectangulartype CI frame & cover confirming to IS 1726-1974 pattern (Par t VI/Sec l). Therate includes excavation, PCC 1:3:6, brcik masonry, cover C I plate (man holecover) of 12mm thick etc complete including earth resistant / testing platecomplete.

389 INST.OF YARD LIGHT POLE NO

Inst. of existing Yard light Pole with arm & light fixtures. J ob also includingof electrical flexible cable and necessary electric al connection completed.

390 INST. OF AIR COMPRESSOR NO

Inst. of supplied Air Compressor in cement concrete base in C C 1:1.5:3 M-20grade with foundation bolt completed.

391 S&I OF AIR COMPRESSOR SHAED NO

Suppling & Installation of prefabricated MS squre pipe stru ctural shade withFinolex make 1.3 mm thk. PVC roofing sheet with necessory bol tingcompleted. Jjob also including of excavation, errection in CC M-15 gradegrouting, aplying of two coat of red oxide and two coats of ena mel paint etccomplete.

392 S&F Of FRP SHEET SHED SQM

Suppling & Fixing of FRP roofing sheet shade in hollow pipe se ction framestructure approved colour with necessory bolting complete d job alsoincluding of excavation, errection in CC M-15 grade groutin g, aplying of twocoats of red oxcide and 2 coats of synthetic enamel paints etc complete.

3700

15

1200

850

10500

1850

2500

2500

12500

2000



393 S& F Of 300MM DIA AIR GAUGE NO

Supplying & Fixing of 300mm dia Air Gauge approved quality of Air Mastermake or equalent brand with nesscery fitting & conn ecation complete.

394 P&L OF 12MM DIA BRADED WIRE FLEXIBLE AIR PIPE RMT

P&L of 12mm dia braided wire flexible air pipe for Air Filling connecting AirGauge.

395 REMOVING OF DEAD STOCK / WATER FROM U/G PRODUCT TA NK UPTO 50 KM.

NO

Removing of dead stock / water from U/G product tank by hand pu mpmanually upto 50 km.

396 REMOVING OF DEAD STOCK / WATER FROM U/G PRODUCT TAN K 51 TO 200 KM.

NO

Removing of dead stock / water from U/G product tank by hand pu mpmanualy 51 to 200 km.

397REMOVING OF 80MM DIA FILL CAP/ 40MM DIA NRV & DIP C AP UP TO 50 KM.

NO

Removing of existing 80mm dia Fill Cap / 40mm dia NRV and Dip Ca p - inCity area

398REMOVING OF 80MM DIA FILL CAP/ 40MM DIA NRV &DIP CA P 50 TO 200 KM.

NO

Removing of existing 80mm Dia Fill Cap / 40mm dia NRV and Dip Ca p - in 51to 200 km.

399 REMOVING OF FACIA BAND RMT

Rem. of existing red & blue facia band from canopy or sales bld g carefullywith disconnect elec. supply completed.

400 REMOVING OF Q&Q TOWER NO

Removing of Q&Q Tower or Air Tower with dismantling of CC base anddebris removing to unobjected place with removing with disc onnectElectrical power supply.

401 REMOVING OF CURTAIN WAL LOGO NO

Removing of Curtain Wall Logo and put it at safe place with dis connectElectrical power supply.

402 REM OF MASTER POLES NO

Removing of Master Pole / Club HP Pole and put it at safe place w ithdisconnect Electrical power supply.

403 REMOVING. OF 40/50MM DIA PIPE LINE RMT

Removing of 40 / 50mm dia existing concealed Pipe Line with ex cavation,back filling and preparation of drive-way completed .

404 REMOVING. OF 80MM DIA PIPE LINE RMT

Removing of 80mm dia existing concealed Pipe Line with excav ation, backfilling and preparation of drive-way completed.

405 DISM.OF CERAMIC / GLAZE TILES WITH BACKING PLASTER SQM

3500

80

1250

1600

150

350

90

350

250

2500

50

75

85SIGN AND SEAL OF BIDDER

Line no. Description Unit Unit RateDism. of Ceramic / Glaze tiles with backing Plaster from existing wall andfloor. Job also including of removing of debris to out side of unobjectedplace.

85



406 DISM.OF EXISTING ASHALT D/W SQM

Dismantling of exiting 80mm thk. Asphalting D/W with 2 layer of 75mm thk.WBM and 230mm thk rubber soling job including of removing of d ebris tounobjected place.

407 APPLYING OF RED OXIDE SQ.MT

P&A of 2 coats of Red Oxide 1st quality of approved manufactur er on steelsurface by thoroughly brush.

408 P&A OF ENAMEL PAINT ON CURBING WALL RMT.

Providing & Applying of One coat of Primer & Two co ats of synthetic paint yellow & black paints as per chequred pattern 300mm to 300mm size.

409 P&L OF PRECAST RCC CURBING RMT.

Providing & Laying of precast RCC curbing block in CC 1:1.5:3 concrete M-20 grade of 300mm x 450mm x 150mm thk. size with excavation, 75 mm thk.PCC & pointing on joint completed.

410 DISMANTILING OF BM WALL CUM

Dismantiling of existing BM wall job also including of debri s to unobjectedplace completed.

411 DISMANTLING OF PCC CUM

Dismantling of existing PCC on D/W or foundation job also inc luding ofdebris to unobjected place completed.

412 DISMANTLING OF RCC CUM

Dismantiling of existing RCC column base/ column / beam and s lab job alsoincluding of debris to unobjected place completed.

413150MM GI PIPE

RMT.

P&F of 150mm 'B' class GI pipes with plugs, nipplex, unions, e tc including allacessories. The pipes should be buried underground in trenc hes etccomplete.

414 200MM GI PIPE RMT.

P&F of 200mm dia 'B' class GI pipes with plugs, nipplex, union s, etcincluding all acessories. The pipes should be buried underg round intrenches etc complete.

415 GROOVE CUTTING RMT.

Groove cutting 15mm wide & 25mm deep in trimix floor after 10 d ays curingof the side floor by working groove cutter & the sand mix in the reafter fillingthe with 40 grade grout proporation 1:1

416 STONE WARE SOIL PIPE [100MM DIA] RMT.

P&L of 100mm dia salt glazed stoneware pipes comple ted.

417 EXPANSION JOINT RMT.

120

32

150

750

55

550

1500

1350

2250

85

195



P&L of expansion joint in RCC D/W slab in salitex board with bi tuminiousprimer 20mm thk. 200mm depth job also including of 35mmx35mm x5mm thk.Angle on top age both side as per detailes drawing.

625



418 INSP. CHAMBER WITH CI COVER 600X600X700 NO

P&C of following size inspection chambers with 230mm thick brick masonryin 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering withneat cement finish, providing 35 kg. CI cover with frame completed.

419 S&F OF CHEQUERED PLATE KG

Supplying, fabricating & fixing at all levels chequred plate including twocoats approved synthetic enamal paint over a primer coat on the exposedsurface wereever necessory and grouting of pocket where ever requiredcompleted.

420 S&F OF GI SHEET SQM

S&F of 18 guage GI sheet board with ISBM Channel by aluminium rivettingarangement of size 20mm long and 6mm dia as shown in the drg. Job alsoincludes painting of GI sheet with 2 coats of red oxide including scafoldingtools/tackles etc complete.

421 Supply and filling Silica Gel Anhydrous Crystals as per standards of HPCL. KG 700

422

S&F Silica Gel double flanged trap made up of MS or as per HPCL Standards to be fitted in 40mm DIA MS Vent Pipeline. The Silica GEL Trap should be of 12-12.5mm MS flanged plate thickness. The cost includes supply and fixing of the same in Petrol / Power Vent Pipeline, inlcuding cost of Labor, tools tackles etc complete.

NO

2300

72

525

3800


Date post:	22-Feb-2018
Category:	Documents
Upload:	lyanh
View:	220 times
Download:	1 times

schedule of Rates - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/2420/Notice/GUJ... ·...

Documents