Schneider PLA Ormani

POLYESTER ENCLOSURES

Presentation 3/2

Selection guide 3/4

SYSTEM 27 Insulating modular boxes 3/14

POLYMEL PLM Monobloc polyester enclosures 3/38

PLAPolyester enclosures 3/68

PLDPolyester enclosures and plinths 3/118

03_000_001_EN.ndd 303_000_001_EN.ndd 3 2/4/08 12:38:532/4/08 12:38:53

3/2

Fibreglass-reinforced polyester enclosures

PLM enclosure installed inside or outside in harsh environments: petrochemical, cement plants, paper plants, iron and steel producers, etc.

PLA enclosures resistant to corrosive chemical and atmospheric agents.

PLD enclosure with incorporated ZD plinth, electrical distribution application.

Inst

alla

tio

n s

yste

ms

Enc

losu

re

feat

ures

WALL MOUNTING

POLYMELSystem 27

Page 3/14 3/38

Degree of protection IP65/IK09 IP66/IK10

No. of sizes/models 14/35 8/26

Dimensions (mm) from 180 270 180 310 215 160

up to 540 720 230 1056 852 350

Mounting plates

Metal

Insulating

Universal

Distribution Chassis

18 mm modules up to 48 up to 240

Internal doors

Canopies

Plinths Acc

es-

sorie

s

03_002_013_EN.indd 203_002_013_EN.indd 2 2/4/08 12:40:282/4/08 12:40:28

3/3

c Insulating modular boxes system 27: composed of the base, with high and low cover variations, transparent and opaque, made of polycarbonate or polyester.

c POLYMEL polyester enclosures:monobloc construction, one single piece highly resistant body, with possible enclosure coupling.

c PLA polyester enclosures and plinths:4 construction systems: – fully closed enclosures, – enclosures with self-ventilated top with canopy and closed bottom, – enclosures with closed top and open plinth-type bottom, – enclosures with self-ventilated top with canopy and open plinth-type bottom.Enclosures with front door, and enclosures with front door and back door. 3 versions of doors: plain, transparent or ribbed.

c PLD-ZD polyester enclosures and plinths:prepared to directly incorporate the fuse holder plinths for electrical distribution.

FLOOR STANDING

3/68 3/118

PLA PLD-ZD

IP65/54/IK10 IP43/54/IK10

40/960 5/5

500 500 320 850 465 320

1500 1250 420 850 1115 320

up to 364

03_002_013_EN.indd 303_002_013_EN.indd 3 2/4/08 12:40:322/4/08 12:40:32

3/4

Hot-press moulded polyester enclosures Selection guide

180 270 180 PLS 1827 - PLSO 1827 - PLSP 1827 FPLS 1827 N TPLS 1827 -


270 270 230 - PLS 2727 A - PLSO 2727A - FPLS 2727 N - TPLS 2727 A


270 360 230 - PLS 2736 A - PLSO 2736 A - FPLS 2736 N - TPLS 2736 A 270 540 180 PLS 2754 - PLSO 2754 - PLSP 2754 FPLS 2754 N TPLS 2754 -

270 540 230 - PLS 2754 A - PLSO 2754 A - FPLS 2754 N - TPLS 2754 A








Low cover ref.Height Width Depth

Page 3/17 3/17 3/17 3/17 3/17 3/17 3/17 3/17

High cover ref. Low cover ref.High cover ref. Low cover ref.High cover ref.

TABLE OF MODELS, DIMENSIONS AND REFERENCES

Transparent cover boxes Opaque cover boxes Polyester box cover Bases Transparent covers

System 27

Box dimensions (mm)

310 215 160 PLM-32 - PLM-32/KT - MB-32 MP-32 MM-32 MF-32 MR-32 -

308 255 160 PLM-3025 - PLM-3025/KT - MB-3025 MP-3025 MM-3025 MF-3025 MR-3025 -

430 330 200 PLM-43 PLM-43/CME PLM-43/KT PLM-43 KT/CME MB-43 MP-43 MM-43 MF-43 MR-43 DPLM-200



747 536 300 PLM-75 PLM-75/CME PLM-75/KT PLM-75 KT/CME MB-75 MP-75 MM-75 MF-75 MR-75 DPLM-300N

847 636 300 PLM-86 PLM-86/CME PLM-86/KT PLM-86 KT/CME MB-86 MP-86 MM-86 MF-86 MR-86 DPLM-300N

1000 800 350 PLM-108 - PLM-108/KT - MB-108 MP-108 MM-108 MF-108 MR-108 DPLM-350

Enclosure dimensions (mm)

Height Width Depth


Plain Three-point Plain Three-point MetalMicroper-

foratedUniversalperforated

Enclosures with plain doors

Enclosures with transparent doors

Mounting platesAdjustable

plate support

Page 3/41 3/41 3/41 3/41 3/48 3/48 3/48 3/48 3/48 3/49

Lock Lock

Bakelite

Polymel

Polyester

Insulating

03_002_013_EN.indd 403_002_013_EN.indd 4 2/4/08 12:40:332/4/08 12:40:33

3/5

TPLSO 1827 - TPLSP 1827 PMM 1827 PMA 1827 PMA/B 1827 12 1 S27 DL/12 DL 27/12

TPLSO 2727 - TPLSP 2727 PMM 2727 PMA 2727 PMA/B 2727 24 2 S27 DL24 DL 27/24

- TPLSO 2727 A - PMM 2727 PMA 2727 PMA/B 2727 - - - DL 27/24

TPLSO 2736 - TPLSP 2736 PMM 2736 PMA 2736 PMA/B 2736 24 2 S27 DL/24-2 DL 27/24-2

S27 DL/36 DL 27/36

- TPLSO 2736 A - PMM 2736 PMA 2736 PMA/B 2736 - - - DL 27/24-2

DL 27/36

TPLSO 2754 - TPLSP 2754 PMM 2754 PMA 2754 PMA/B 2754 48 4 S27 DL748 DL 27/48

- TPLSO 2754 A - PMM 2754 PMA 2754 PMA/B 2754 - - - DL 27/48

TPLSO 3636 - TPLSP 3636 PMM 3636 PMA 3636 PMA/B 3636 - - - -


- TPLSO 3654 A - PMM 3654 PMA 3654 PMA/B 3654 - - - -





3/17 3/17 3/17 3/17 3/17 3/17 3/35 3/17

Steel Polyester Bakelite No. of rows ReferenceLow cover ref. High cover ref.No. of modules

18 mm

Opaque covers Polyester covers Boxes with DINMEL modular chassis DINMEL chassis Mounting plates

- - - - - - - -

DL/PLM18 2 2 18 - PI-3025/PLM - -

DLA-24 2 2 24 - PIP-43 SFP-300 -

DLA-48 3 3 48 - PIP-54 SFP-400 SFS/PLM

DLA-48P 3 3 48 - PIP-64 SFP-400 SFS/PLM

DLA-66 4 3 66 1

PIP-75 SFP-500 - 4 4 88 -

DLA-84 4 3 84 1 PIP-86 SFP-600 -

DLA112 4 4 112 -

DLA-240 6 6 234 - PIP-108 - -

Reference No. of rows Quantity

Automatic rail

No. of modules 18 mm

No. of plates

DINIMEL chassis Internal door set Post fixing set Floor-mounting pillar

3/63 3/45 3/45 3/43

03_002_013_EN.indd 503_002_013_EN.indd 5 2/4/08 12:40:412/4/08 12:40:41

3/6



Height Width DepthNo. of doors

Nominal dimensions (mm)

IP65

120°

Flat

PlainDoor

Lock

Door opening

Degree of protection

Ribbed Transparent

Completely closedPLA enclosures with rear panel

500 500 320 1 PLA 553 PLA 553 R PLA 553 KT PLA 553 T PLA 553 TR PLA 553 TKT

420 1 PLA 554 PLA 554 R PLA 554 KT PLA 554 T PLA 554 TR PLA 554 TKT

750 320 1 PLA 573 PLA 573 R PLA 573 KT PLA 573 T PLA 573 TR PLA 573 TKT






































IP54

120°

Handle

Plain Ribbed Transparent

Self-ventilated top with canopy

Page 3/73 3/73 3/73 3/75 3/75 3/75

PLA

03_002_013_EN.indd 603_002_013_EN.indd 6 2/4/08 12:40:432/4/08 12:40:43

3/7

PLAZ 553 PLAZ 553 R PLAZ 553 KT PLAZ 553 T PLAZ 553 TR PLAZ 553 TKT








































IP54

120°

Handle


Open plinth-type base

IP54

180°

Handle


Self-ventilating top with canopy and open plinth-type base

3/77 3/77 3/77 3/79 3/79 3/79

03_002_013_EN.indd 703_002_013_EN.indd 7 2/4/08 12:40:442/4/08 12:40:44

3/8

Page 3/73 3/73 3/73 3/75 3/75 3/75





IP65

120°

Flat

PlainDoor

Lock

Door opening

Degree of protection

Ribbed Transparent

Completely closedPLA enclosures with rear door

500 500 320 1 PLA 553 P PLA 553 PR PLA 553 PKT PLA 553 TP PLA 553 TPR PLA 553 TPKT

420 1 PLA 554 P PLA 554 PR PLA 554 PKT PLA 554 TP PLA 554 TPR PLA 554 TPKT

750 320 1 PLA 573 P PLA 573 PR PLA 573 PKT PLA 573 TP PLA 573 TPR PLA 573 TPKT






































IP54

120°

Handle


Self-ventilated top with canopy

PLA

03_002_013_EN.indd 803_002_013_EN.indd 8 2/4/08 12:40:452/4/08 12:40:45

3/9

3/77 3/77 3/77 3/79 3/79 3/79

PLAZ 553 P PLAZ 553 PR PLAZ 553 PKT PLAZ 553 TP PLAZ 553 TPR PLAZ 553 TPKT








































IP54

120°

Handle


Open plinth-type base

IP54

180°

Handle


Self-ventilating top with canopy and open plinth-type base

03_002_013_EN.indd 903_002_013_EN.indd 9 2/4/08 12:40:452/4/08 12:40:45

3/10




500 500 320 1 PMM 55 PMB 55 PMA 55 PMR 55 - - -

420 1 PMM 55 PMB 55 PMA 55 PMR 55 - - -

750 320 1 PMM 75 PMB 75 PMA 75 PMR 57 - - -

420 1 PMM 75 PMB 75 PMA 75 PMR 57 - - -

1000 320 2 PMM 510 PMB 510 PMA 510 PMR 55 + PMR 55 - - -

420 2 PMM 510 PMB 510 PMA 510 PMR 55 + PMR 55 - - -

1250 320 2 PMM 55 + PMM 75 PMB 55 + PMB 75 PMA 55 + PMA 75 PMR 55 + PMR 57 - - -

420 2 PMM 55 + PMM 75 PMB 55 + PMB 75 PMA 55 + PMA 75 PMR 55 + PMR 57 - - -

750 500 320 1 PMM 75 PMB 75 PMA 75 PMR 75 MOL 75 DLP 57/76 57/76

420 1 PMM 75 PMB 75 PMA 75 PMR 75 MOL 75 DLP 57/76 57/76

750 320 1 PMM 77 PMB 77 PMA 77 PMR 77 MOL 75 DLP 99/132 99/132


1000 320 2 PMM 710 PMB 710 PMA 710 PMR 75 + PMR 75 MOL 75 DLP 57/76 + DLP 57/76 114/152

420 2 PMM 710 PMB 710 PMA 710 PMR 75 + PMR 75 MOL 75 DLP 57/76 + DLP 57/76 114/152



1000 500 320 1 PMM 105 PMB 105 PMA 105 PMR 105 MOL 100 DLP 95/114 95/114


750 320 1 PMM 107 PMB 107 PMA 107 PMR 107 MOL 100 DLP 165/198 165/198






1250 500 320 1 PMM 125 PMB 125 PMA 125 PMR 125 MOL 125 DLP 114 P/133 114/133

420 1 PMM 125 PMB 125 PMA 125 PMR 125 MOL 125 DLP 114 P/133 114/133

750 320 1 PMM 127 PMB 127 PMA 127 PMR 127 MOL 125 DLP 198 P/231 198/231

420 1 PMM 127 PMB 127 PMA 127 PMR 127 MOL 125 DLP 198P/231 198/231

1000 320 2 PMM 1210 PMB 1210 PMA 1210 PMR 125 + PMR 125 MOL 125 DLP 114P/133 + DLP 114P/133 228/266

420 2 PMM 1210 PMB 1210 PMA 1210 PMR 125 + PMR 125 MOL 125 DLP 114P/133 + DLP 114P/133 228/266

1250 320 2 PMM 1212 PMB 1212 PMA 1212 PMR 125 + PMR 127 MOL 125 DLP 114P/133 + DLP 198P/231 312/364

420 2 PMM 1212 PMB 1212 PMA 1212 PMR 125 + PMR 127 MOL 125 DLP 114P/133 + DLP 198P/231 312/364

1500 500 320 1 PMM 155 PMB 155 - PMR 155 MOL 150 - -

420 1 PMM 155 PMB 155 - PMR 155 MOL 150 - -

750 320 1 PMM 157 PMB 157 - PMR 157 MOL 150 - -

420 1 PMM 157 PMB 157 - PMR 157 MOL 150 - -

1000 320 2 PMM 1510 PMB 1510 - PMR 155 + PMR 155 MOL 150 - -

420 2 PMM 1510 PMB 1510 - PMR 155 + PMR 155 MOL 150 - -

1250 320 2 PMM 1512 PMB 1512 - PMR 155 + PMR 157 MOL 150 - -

420 2 PMM 1512 PMB 1512 - PMR 155 + PMR 157 MOL 150 - -

Metal mounting plate

Insulating mounting plate Universal perforated mounting plate

Set of 2 profiles for universal chassis

Modular distribution chassis


No. of modules 18 mm

Reference

Page 3/93 3/94 3/94 3/95 3/97 3/112

(1) Only for enclosures with closed base reference PLA…(2) Only for enclosures with open plinth-type base reference PLAZ…

PLA

Bakelite Polyester

03_002_013_EN.indd 1003_002_013_EN.indd 10 2/4/08 12:40:462/4/08 12:40:46

3/11

PIPLA 55 ZNPLA 53 ZHPLA 53 TJPLA 53


BRF 8 PLA 8 - - PIPLA 57 ZNPLA 73 ZHPLA 73 TJPLA 73

BRF 8 PLA 8 BRP 7 PLA 7 PIPLA 57 ZNPLA 74 ZHPLA 74 TJPLA 74

PIPLA 55 + PIPLA 55 ZNPLA 103 ZHPLA 103 TJPLA 103




































19” fixed rack

19” pivoting rack

Internal doors Bases (1) Plinths (2) Canopies

No. of units1 = 44.45 mm

3/118 3/118 3/89 3/85 3/86 3/86

No. of units1 = 44.45 mm

03_002_013_EN.indd 1103_002_013_EN.indd 11 2/4/08 12:40:542/4/08 12:40:54

3/12


Height Width Depth Reference Reference Reference ReferenceNo. of doors

No. of locks

No. of plates per enclosure

850 465 320 PLD-85/00 1 1 APLD-85 1 ZD-53/00 BPLD

850 590 320 PLD-86/0 1 1 APLD-86 1 ZD-63/0 BPLD

850 785 320 PLD-88/1 1 1 APLD-88 1 ZD-83/1 BPLD

850 1115 320 PLD-812/2 2 1 APLD-812 2 ZD-123/2 BPLD

850 1115 320 PLD-812/2C 2 2 APLD-812 2 ZD-123/2 BPLD


PLD-ZD

Page 3/121 3/121 3/123 3/125

Enclosure dimensions (mm)

Enclosures Mounting plates Plinth Rack

03_002_013_EN.indd 1203_002_013_EN.indd 12 2/4/08 12:40:562/4/08 12:40:56

3/13

03_002_013_EN.indd 1303_002_013_EN.indd 13 2/4/08 12:41:002/4/08 12:41:00

6 5

321

8 7

4

3/14

Insulating modular boxes resistant against outdoor conditions System 27

03_014_015_EN.indd 1403_014_015_EN.indd 14 2/4/08 12:42:162/4/08 12:42:16

3/15

5 Internal view without protective panel with detail of the neutral-earth terminal block of the modular chassis.

1 Possibility of using the interior part of the TPLSP cover (in PLSP polyester boxes) to fix the plates using an M5 insert.

2 Side lock (optional), may be available with key lock.

4 Rear view of box with PF-27 wall-fixing piece in place.

8 M6 inserts for fixing the mounting plate or various equipment.

7 Sealable cover-base lock, screwdriver operated (standard supply).

6 Box completely mounted with detail of hinge, protective panel and removable blanking plate fixing.

3 Insulating polyester mounting plate fixed to the back. Option of metallic or bakelite plate.

03_014_015_EN.indd 1503_014_015_EN.indd 15 2/4/08 12:42:172/4/08 12:42:17

3/16

SYSTEM 27 Insulating modular boxesIP55 (EN 60529)

PLS 3654

Insulating modular boxes comprised of BASES made of fibreglass-reinforced polyester and COVERS made of polycarbonate or fibreglass-reinforced polyester, depending on the model.PLS and PLSO boxes with polycarbonate covers on the transparent and opaque versions.PLSP boxes with fibreglass-reinforced polyester covers.Opaque bases and covers in greyRAL-7032.

c Modular dimensions that, in addition to its individual use, permit coupling

of boxes.

c Self-extinguishing, double insulation.

c Sealing gasket between base and cover.

c Dielectric rigidity > 5 kV, insulation resistance > Ω.

c Operating temperature from –30 °C to 120 °C for PLS and PLSO models

and 150 °C for PLSP models.

c Easily machined with conventional tools.

c Locking screw, screwdriver operated (standard supply).

c IK09.

03_016_024_EN.indd 1603_016_024_EN.indd 16 2/4/08 12:46:032/4/08 12:46:03

3/17

Insulating modular boxesIP55 (EN 60529)SYSTEM 27

180 270 180 PLS 1827 PLSO 1827 PLSP 1827 - -

270 270 180 PLS 2727 PLSO 2727 PLSP 2727 - -

270 270 230 - - - PLS 2727 A PLSO 2727 A

270 360 180 PLS 2736 PLSO 2736 PLSP 2736 - -

270 360 230 - - - PLS 2736 A PLSO 2736 A

270 540 180 PLS 2754 PLSO 2754 PLSP 2754 - -

270 540 230 - - - PLS 2754 A PLSO 2754 A

360 360 180 PLS 3636 PLSO 3636 PLSP 3636 - -

360 540 180 PLS 3654 PLSO 3654 PLSP 3654 - -

360 540 230 - - - PLS 3654 A PLSO 3654 A

360 720 230 - - - PLS 3672 A PLSO 3672 A

540 540 180 PLS 5454 PLSO 5454 PLSP 5454 - -

540 540 230 - - - PLS 5454 A PLSO 5454 A

540 720 230 - - - PLS 5472 A PLSO 5472 A

Height(mm)

Width(mm)

Depth(mm)

Transparent Opaque Polyester Transparent

High cover boxes

Opaque

Low cover boxes

TABLE OF MODELS, DIMENSIONS AND REFERENCES, MODULAR BOXES

Height(mm)

Width(mm)

Depth(mm)

180 270 180 FPLS 1827 N TPLS 1827 TPLSO 1827 TPLSP 1827 - -


270 270 230 FPLS 2727 N - - - TPLS 2727 A TPLSO 2727 A












Base 135 mm

Opaque 45 mm Polyester 45 mm Transparent 95 mm

High cover

Opaque 95 mm

Low cover

TABLE OF MODELS, DIMENSIONS AND REFERENCES, BASES AND COVERS

Transparent45 mm

Mounting plates Modular chassis

To be coupled to boxes(dimensions)

Metal Polyester Bakelite

To be coupled to boxes(dimensions)

Height (mm) Width (mm) Height (mm) Width (mm) Reference No. of modules

180 270 PMM 1827 PMA 1827 PMA/B 1827 180 270 DL 27/12 12

270 270 PMM 2727 PMA 2727 PMA/B 2727 270 270 DL 27/24 24

270 360 PMM 2736 PMA 2736 PMA/B 2736 360 270DL 27/24-2DL 27/36

2436

270 540 PMM 2754 PMA 2754 PMA/B 2754 540 270 DL 27/48 48

360 540 PMM 3636 PMA 3636 PMA/B 3636

360 540 PMM 3654 PMA 3654 PMA/B 3654

360 720 PMM 3672 PMA 3672 PMA/B 3672

540 540 PMM 5454 PMA 5454 PMA/B 5454

540 720 PMM 5472 PMA 5472 PMA/B 5472

TABLE OF MODELS, DIMENSIONS AND REFERENCES, PLATES AND CHASSIS

03_016_024_EN.indd 1703_016_024_EN.indd 17 2/4/08 12:46:052/4/08 12:46:05

3/18

SYSTEM 27 Insulating modular boxesIP55 (EN 60529)

45

2

270200

2494 2

1

3

249

24924

9

270

200

122.2122.3

138 95

23*

45

2

180110

1591 3

2

4

159

24924

9

270

200

122.2122.3

138

45

2

360290

3394 2

1

3

339

24924

9

270

200

122.2122.3

138 95

23*

45

3

360290

339

4 2

1

3

339

339

339

360

290

122.212

2.7

138

54070200 200

5196 3

1 2

5 4

260 260

249

249

270

200

45

2.5122.2122.7

138 95

2.53*

72070290 290

6997 4

8 3

1 2

6 5

350 350

260

260

519

540

7020

020

0

122.212

2.7

138 95

4

72070290 290

699

6 3

1 2

5 4

350 350

339

339

360

290

122.212

2.7

138 95

3.5

54070200 200

5197 4

8 3

1 2

6 5

260 26026

026

0

519

540

7020

020

0

122.212

2.7

138 45 95

3 3

54070200 200

519

6 3

1 2

5 4

260 260

339

339

360

290

122.212

2.7

138 45 95

3 3

1827…

2727…

2736…

3636…

2754…

* The thickness of 3 mm corresponds to the polyester cover.

5472…

3672…

5454…

3654…

Dimensions (mm)

A Coupling to the back with low cover.B Coupling to the back with high cover..C D Interior view of back corner, detail of the bosses with M6 inserts.E F Interior view of the corner of the polyester cover with housing for the expandable nut.Ref.: TE-25 for M5 screws.

A C E

B D F

03_016_024_EN.indd 1803_016_024_EN.indd 18 2/4/08 12:46:062/4/08 12:46:06

3/19

Example of couplingSuite of general, busbar, meter and distribution boxes.

All boxes may be coupled on any of their sides. The coupling may be done using UM modular joints and PS fastening pieces.

Insulating modular boxesIP65 (EN 60529)SYSTEM 27

PS 2C-27 UM-27/270

S27-DL/48

Cover TL-27/270 with cable glands

TL-27/270UM-27/270EGB-27TL-27/270

03_016_024_EN.indd 1903_016_024_EN.indd 19 2/4/08 12:46:082/4/08 12:46:08

3/20

SYSTEM 27 Composition accessories

Manufactured with fibreglass-reinforced polycarbonate. Pieces prepared for coupling the boxes on any of their lateral sides.

c Sealing gasket on both sides.

c Supplied with all the hardware necessary for fixing and the openings template.

Modular couplings

ReferenceTo couple to openings (mm)

110 (nominal 180) UM 27/180

200 (nominal 270) UM 27/270

290 (nominal 360) UM 27/360

Side cut-out press, Ref.: PUC-27.

To order boxes with lateral openings, you must add the numbers of the sides that you wish to have cut to the reference of the basic box.These numbers are indicated on the dimensions panel as well as raised on the bases themselves. Example: a 270 × 540 mm box with low transparent cover and openings on sides 1, 3 and 5 would be: PLS-2754/1-3-5.

Openings

03_016_024_EN.indd 2003_016_024_EN.indd 20 2/4/08 12:46:102/4/08 12:46:10

3/21

Composition accessoriesSYSTEM 27

For coupling 2, 3, or 4 boxes with the possibility of wall fixing.

Box coupling pieces

ReferenceTo couple

2 boxes PS2C-27

3 or 4 boxes PS4C-27

M6×18 cylinder head screws.

Manufactured with fibreglass-reinforced polyester. Easily machined with conventional tools for cable entry.

c With a sealing gasket.

c Supplied with all the hardware necessary for fixing and the openings template.

Side covers

ReferenceTo couple to openings (mm) )

200 (nominal 270) TL 27/270

290 (nominal 360) TL 27/360

Wall-fixing parts

ReferenceMaterial

Passivated zinc-coated steel PF-27

Stainless steel PF-27/ I

03_016_024_EN.indd 2103_016_024_EN.indd 21 2/4/08 12:46:112/4/08 12:46:11

3/22

Transport handle

ReferenceMaterial

Polyamide ATM-27

Rail-fixing pieces

Stud∅ 8

Rail fixing Direct wall-fixing

RailCNT-20

M6×30cylinder head screw

50 mm long ribbedhead screw

NutBN-206

SYSTEM 27 Composition accessories

Has incorporated all the elements necessary for fixing and adjusting to a post.

Post fixing

ReferenceTo couple to module width (mm)

270 FSP-27/270

360 FSP-27/360

540 FSP-27/540

03_016_024_EN.indd 2203_016_024_EN.indd 22 2/4/08 12:46:132/4/08 12:46:13

Fig. 1

Fig. 2

Fig. 2Fig. 1

PPA-27

CL-27

CLL-27

TCD-27/4 N TCM-27/4 N

TCT-27/4 N

LT-27

3/23

Composition accessoriesSYSTEM 27

Locks for insulated modular boxes

Specifications ReferenceTypes of operation with

Set of 4 locks Screwdriver TCD-27/4 N

Set of 6 locks Standard supply in boxes (PLS) Screwdriver TCD-27/6 N

Set of 8 locks Screwdriver TCD-27/8 N

Set of 4 locks Manual TCM-27/4 N

Set of 6 locks Standard in boxes (S27DL) Manual TCM-27/6 N

Set of 8 locks Manual TCM-27/8 N

Set of 4 triangle locks LT-27 TCT-27/4 N



Double bar side lock, possibility DBP CL-27 of fixing the wing key to the lock

Side lock with key operation CLL-27

Metal sealing sheet PPA-27 (included in standard supply)

Insulated seal PPS-27

Triangle key LT-27

* In rows of 12 modules mounted vertically.** In rows of 17 modules mounted horizontally.

Allow access to the interior of the enclosure, maintaining the IP65 degree of protection.Made of transparent polycarbonate.

Windows for automatic switches

Fig. No.Low cover

Reference

High cover A B Low cover High coverNo. of

modules

C

VA 27/2M VA 27/2MA 2 1 78 60 15 25

VA 27/4M VA 27/4MA 4 1 78 95 15 25

VA 27/6M VA 27/6MA 6 1 78 130 15 25

VA 27/8M VA 27/8MA 8 1 78 165 15 25

VA 27/10M VA 27/10MA 10 1 78 200 15 25

VA 27/12M VA 27/12MA 12 1 78 235 15 25

VA 27/16M - 16 2 195 165 13 -

VA 27/24M - 24* 2 196 235 13 -

VA 27/36M - 36* 2 248 235 13 -

VA 27/51M - 51** 2 248 325 13 -

03_016_024_EN.indd 2303_016_024_EN.indd 23 2/4/08 12:46:142/4/08 12:46:14

3/24

SYSTEM 27 Mounting accessories

Mounting plates for fixing single-phase or three-phase meters made of polyester with fibre-glass, in RAL-7032.

Plates for meters

Single-phase Three-phaseTo couple to boxes

Height Width No. of meters Reference No. of meters Reference

270 270 1M P1M-27 - -

1M (displaced) P1M-P27 - -

270 360 1M P1M-2736 1T P1T-27

2M P2M-27 - -

270 540 2M P2M-27E 1T P1T-27E(1)

2M (vertical) P2M-27V - -

3M P3M-27 - -

360 540 4M P4M-27V 2T P2T-27

- - 3T P3T-27

540 540 6M P6M-27V 2T P2T-27E

- - 3T P3T-27E

360 720 5M P5M-27 3T P3T-27H

6M P6M-27V 4T P4T-27

540 720 8M P8M-27 3T P3T-27G

9M P9M-27 6T P6T-27

10M P10M-27 - -

(1) 1 vertical three-phase.

Metal insert nuts for fixing equipment on polyester and bakelite insulated mounting plates.

Fixing nuts

Thread MReference

TE-3 3

TE-4 4

TE-5 5

TE-6 6

TE-8 9

TE-10 10

TE-12 12

03_016_024_EN.indd 2403_016_024_EN.indd 24 2/4/08 12:46:172/4/08 12:46:17

3/25

Current distribution accessories

Made of 6.6 nylon in natural colour or black for outdoor conditions.

Adjustable ties

White BlackL ∅

minimum∅

maximum

M

Reference Use

LZ25100 LN25100 100 2.5 1.6 22

LZ25200 LN25200 200 2.5 1.6 49

LZ35150 LN35150 150 3.5 1.6 35

LZ35200 LN35200 200 3.5 1.6 49

LZ35300 LN35300 300 3.5 1.6 75

LZ46150 LN46150 150 4.6 1.6 36

LZ46200 LN46200 200 4.6 1.6 49

LZ48270 LN48270 270 4.8 1.6 73

LZ46390 LN46390 390 4.6 1.6 109

LZ76390 LN76390 390 7.6 4.7 108

To tighten and cut the adjustable ties to size. They facilitate wiring and save time, preventing the packets of cables from loosening.

Tool adjustable according to the thickness of the tie. Can be used with the following models: LZ25100 up to LZ46390. Ref.: MARK3.

A very light and ergonomic tool, the cut on the tie is done by twisting the tool. Can be used on the following models of ties: LZ25100 up to LZ46390. Ref.: MARK20, 21.

Tightening tools

Reference

MARK3 2.5 ÷ 4.8

Admissible width ties

Reference

MARK20 2.5 ÷ 4.8

MARK21 4.6 ÷ 7.6


SYSTEM 27

03_025_037_EN.indd 2503_025_037_EN.indd 25 2/4/08 12:47:452/4/08 12:47:45

3/26


To use with soft materials: 7 mm Ø hole, or hard materials: 8 mm Ø hole. Ties up to 9 mm in width can be coupled. Material: black 6.6 nylon.

Ref.: LOK01.

Stud

To attach one or two ties, mounted with a single screw. Material: 6.6 nylon. Allows for attaching ties from the entire range.

Tie fixing support

Reference A B Fixing screwAdmissible width

tiesC

KR6 12 18 9 M4 2.5 ÷ 4.8

KR8 14.5 25 12 M6 2.5 ÷ 7.6

Allows fixing ties from the series LZ25100 up to LZ46390 on panels up to 3.2 mm thick. Material: 6.6 nylon.

Locking clips

Reference

SFC1 6 3.2 1

SFC2 6 1 2

FigureMax. panel

thickness mm∅ perforation

mm

SFC2 SFC1

Fig. 1 Fig. 2

SYSTEM 27

03_025_037_EN.indd 2603_025_037_EN.indd 26 2/4/08 12:47:462/4/08 12:47:46

adhesive support

3/27


Permits insertion of 1 tie from 4 points at a 90º angle. Attaches ties from the series LZ25100 up to LZ46390. Material: 6.6 nylon.

Self-adhesive support base

Reference A B C EAdmissible width

tiesD

MB3A 19.1 19.1 4.8 3.2 13.2 2.5 ÷ 3.5

MB4A 28.5 28.5 5.5 4 20.2 2.5 ÷ 4.8

To attach ties from any series. Material: 6.6 nylon.

Tie fixing support

Reference

LKC 2.5 7.6 M5

Fixing screwAdmissible width

ties mm

To transform normal ties into ties with fixing heads, introduce a tie into this head before closing it on the cable bundle. Material: 6.6 nylon.

Support heads


tiesC

FH18 7.1 13.3 4 M4 2.5

FH30 9.5 17.9 4.7 M5 3.5

FH50 11.3 22.2 6.2 M6 4.7

SYSTEM 27

03_025_037_EN.indd 2703_025_037_EN.indd 27 2/4/08 12:47:482/4/08 12:47:48

3/28


2 versions, fixed and adjustable, ∅ from 5 to 25.4 mm. Material: black 6.6 nylon.

Fixing loop for tubes, hoses, etc.

NX 1-3-5 NX 8-11-14

Reference∅ A

min. - max.B D EC

NX1 5 3.5 1 6.2 13.7

NX3 8 3.9 1 9.4 20.5

NX5 12 3.9 1 9.4 24

NX8* 14.3 ÷ 15.8 4 1.3 12.6 32

NX11 17.4 ÷ 20 4 1.3 12.6 37

NX14 22.2 ÷ 25.4 4.3 1.5 16 45

*The NX8 model only has 3 adjustment holes.

For tube or cable entry. Models EGB-27 made of neoprene.

Membrane gland

Covers the head of the tie in its end, thus obtaining neater cabling.

Material: 6.6 nylon.

Lateral tie fixing support

Reference

LKM/HE 2.5 7.6 M5


ties mm

SYSTEM 27

03_025_037_EN.indd 2803_025_037_EN.indd 28 2/4/08 12:47:492/4/08 12:47:49

Ø A

Ø B

3/29


Insulating membrane glands made of PVC with entry that can be adjusted for cables or tubes (see page 3/30).

Adjustable membrane glands

Reference Fig. Ø A Ø B* Ø C Ø D E FØ cable Tube

Capacity

ECPC-3 1 25 21.5 18 5 3.2 13 5 to 18 Pg 9 to 11

ECPC-5 1 33 29.5 26 5 3.2 20 5 to 26 Pg 9 to 16

ECPC-6 1 43 38.5 36 5 3.2 22 5 to 36 Pg 9 to 21

ECPC-9 2 70 63 60 28 3 20 28 to 60 Pg 21 to 48

ECPC-15 2 98 90 87 28 3 23 28 to 87 Pg 21 to 48

* Mounting perforation.

SYSTEM 27

Fig. 1 Fig. 2

Small protective sleeves for cables coming out of tubes, as indicated in the instructions for MI BT 019. Made of flexible and durable PVC, in light grey colour.

Protective sleeves

Reference A Ø B Tube

PC-1 15.2 12.7 Pg 9

PC-2 18.6 16 Pg 11

PC-3 20.4 17.8 Pg 13.5

PC-4 22.5 19.8 Pg 16

PC-5 28.3 25.3 Pg 21

PC-6 37 33.6 Pg 29

PC-7 47 43 Pg 36

03_025_037_EN.indd 2903_025_037_EN.indd 29 2/4/08 12:47:502/4/08 12:47:50

3/30

Current distribution accessoriesSYSTEM 27

ASE 27/360

AE-25

AI-25

No. of platesTo couple to the side of

box (mm)ReferencePlate width (mm)

360 4 15/20 ASE 27/360

270 4 15/20 AE 25

- 1 15/20/30 AI 25

Insulators

To form busbars. Made of fibreglass-reinforced polycarbonate.

Useful information about Pg tubes and HIMEL accessories to be coupled

Desig-nation

Øexterior

SteelFlexible

steelPVC Insert Thread

Protective sleeves

Adjustable membrane

glandsPlain plugs

Adjustablemembrane glands

Flexible steel with

PVC

Cables inserted*Ø interior To the perforationsTo the tube

4 EC-1 to EC-7

Pg 9 15.2 12.7 12.4 12 11.1 6 2.5 - - 16 14 ECPC-3 to ECPC-6 PC-1 - -

ECN-5 to ECN-10

10 4 2.5 EC-2 to EC-7 EC-1

Pg 11 18.6 16 15.5 14.5 14.2 16 6 4 2.5 19 17.5 ECPC-5; ECPC-6 PC-2 EC-2 TC-1

25 ECN-5 to ECN-10 ECN-1

EC-3 to EC-7 EC-3

Pg 13.5 20.4 17.8 17.5 16.3 16 35 10 6 4 21 19.5 ECPC-5; ECPC-6 PC-3 ECPC-3 TC-2

ECN-5 to ECN-10

EC-4 to EC-7

Pg 16 22.5 19.8 18.7 18.5 17.6 50 16 10 6 23 21.5 ECPC-5; ECPC-6 PC-4 EC-4 TC-3

ECN-5 to ECN-10

EC-5 to EC-7 EC-5

Pg 21 28.3 25.3 24.7 23 23 70 25 16 10 29 27 ECPC-6 to ECPC-15 PC-5 ECPC-5 TC-4

ECN-6 to ECN-10 ECN-5

95 35 25 16 EC-6; EC-7 EC-6 TC-5

Pg 29 37 33.6 33.5 31 31 120 50 35 25 38 35.5 ECPC-9; ECPC-15 PC-6 ECPC-6 TCP-5

150 ECN-7; ECN-10 ECN-6

185 35 EC-7 EC-7

Pg 36 47 43 41.5 41 40.3 240 70 50 50 48 45.5 ECPC-9; ECPC-15 PC-7 ECN-7 TC-6

300 ECN-10

95 70 ECPC-9; ECPC-15

Pg 42 54 50 48 48 47 - 120 95 70 55 52.5 ECN-10 - - -

120 95 ECPC-9; ECPC-15

Pg 48 60 56 54.2 52.5 51.4 - 150 150 120 61 58 ECN-10 - - -

* Number and section in mm2 of the conductors that may be housed inside each tube (orientative).

For more information, consult the electrotechnical rules for low voltage (MI BT 019).

1 2 3 4

MODELS, DIMENSIONS AND REFERENCES

No. of conductors

Tubes HIMEL accessories to be coupled

Ø perforations to

03_025_037_EN.indd 3003_025_037_EN.indd 30 2/4/08 12:47:512/4/08 12:47:51

3/31


Split bridges

ReferenceCable section mm2

95 TS-25/95

150 TS-25/150

240 TS-25/240

Base of safety terminals made of black matte self-extinguishing polyamide-6; terminal of brass MS-58

(DIN17660); ring of tempered steel zinc dichromate; cap made of orange self-extinguishing polypropylene.

c Anti-cut. The connection is made using a tightening mechanism that spreads the pressure out throughout the entire contact surface, avoiding the occasional rubs and stresses that damage the conductors.

c Loosening proof. The ring that surrounds the brass body ensures that the pressure exerted by the conductors cannot open the terminal and loosen the connection.

c Total insulation. All the SIGMA terminals are supplied with a terminal cap, avoiding any accidental contact with live parts.

All the calibres may be coupled one to the other, allowing the formation of strips of any length. Service voltage: 500 V.

Sigma safety terminals

Reference

S.04 1 × 4 30 20 13 21 4

S.06 1 × 6 33 25 16 24 7

S.10 1 × 10 38 28 16 28 6

S.16 1 × 16 42 32 19 32 9

S.25/35 1 × 35 46 38 23 34 11

S.50 1 × 50 52 45 27 40 15

S.70 1 × 70 55 50 30 40 15

S.95/100 1 × 100 58 54 33 40 20

NOTE: each terminal accepts up to 2 conductors of the section indicated.

Section m/m2 A B C D E

03_025_037_EN.indd 3103_025_037_EN.indd 31 2/4/08 12:47:522/4/08 12:47:52

3/32

ReferenceCable bypass section (mm2)

Plate thickness (mm) Figure


Terminals especially designed for branching cables on plates; their main application is busbar connection.

BBH terminals are made of a tinned, hot cast copper alloy and are suitable for connecting to a conductor of copper or aluminium indistinctly (bimetal).

Bimetal BBH terminals

Reference

BBH-29 6-50 -

BBH-29C* 6-50 -

BBH-30 10-95 -

BBH-31 16-150 -

BBH-32 50-240 -

BBH-29D 6-50 6-50

BBH-29DC* 6-50 6-50

BBH-30D 10-95 10-95

BBH-31D 25-150 16-150

BBH-32D 95-240 5-240

Main section(mm2)

Bypass section(mm2)

Reference

BBH-29P 6-50 -

BBH-29PC* 6-50 -

BBH-29DP 6-50 6-50

BBH-29DPC* 6-50 6-50

* Include terminal cover CBBH-29.

Main section (mm2)

Bypass section(mm2)

BBH-29 BBH-29D

BBH-29P BBH-29DP

Plate entry and bypass by cable.

Plate/cable terminals

1

* Included in standard supply.

Number of terminals × section in (mm2)

Earth and neutral bypass terminal blocks with insulated plinth.

Direct fixing by pressure on the profile supplied by the chassis itself.

Bypass terminal blocks

RBLZ/21656* 2 × 16 mm2 + 5 × 6 mm2

RBLZ/21686 2 × 16 mm2 + 8 × 6 mm2

RBLZ/216146 2 × 16 mm2 + 14 × 6 mm2

RBLZ/216296 2 × 16 mm2 + 29 × 6 mm2

Reference

2

BPCH 516 1.5 to 16 5 2

BPCH 550 1.5 to 50 5 2

BPCH 5120 16 to 120 5 2

BPCH 1016 1.5 to 16 10 1

BPCH 1050 1.5 to 50 10 1

BPCH 10120 16 to 120 10 1

03_025_037_EN.indd 3203_025_037_EN.indd 32 2/4/08 12:47:532/4/08 12:47:53

3/33

Natural ventilation accessoriesComplementary accessories

Ventilation devices

To connect the inside of the enclosure with the exterior atmosphere and prevent condensation.

Specifications Reference

∅ 19 VM-25

∅ 29 VM-27

SYSTEM 27

VM-25 VM-27

03_025_037_EN.indd 3303_025_037_EN.indd 33 2/4/08 12:47:582/4/08 12:47:58

3/34

SYSTEM 27 Applications

c Opening for cable entry with TL cover.

c Double-insulation mounting.

c Excellent resistance to corrosive environments.

c Exterior hinges, allowing a door opening of approximately 180°.

c Removable blanking plate with a width of 36 mm (2 modules), standard

supply one per row.

c A lateral double bar lock CL-27 or key CLL-27 can be incorporated.

S27 DL/48

Modular PLS boxes composed of base and transparent low cover, with hinges and manually-operated and screwdriver-operated locks.DL incorporated chassis composed of automatic DIN-35 rails, insulated panel protector and neutral-earth terminal blocks of 2 × 16 + 5 × 6 mm2.

Insulating modular boxes with distribution chassis

03_025_037_EN.indd 3403_025_037_EN.indd 34 2/4/08 12:47:582/4/08 12:47:58

S27 DL/12

S27 DL/24

S27 DL/24-2

S27 DL/48

S27 DL/36

3/35

External dimensions (mm)

ReferenceTotal capacity in 18 mm

modulesNo. of rows Approx. weight (kg)

Height (A)

Width (B)

Depth (C)

180 270 180 S27 DL/12 12 1 1.7

270 270 180 S27 DL/24 24 2 2.5

360 270 180 S27 DL/24-2 24 2 2.7

360 270 180 S27 DL/36 36 3 2.8

540 270 180 S27 DL/48 48 4 3.8

ApplicationsSYSTEM 27

Dimensions (mm)


03_025_037_EN.indd 3503_025_037_EN.indd 35 2/4/08 12:47:592/4/08 12:47:59

3/36

SYSTEM 27 Applications

Blanking plate in self-extinguishing insulating material for total or partial coverage of the window for automatic switches.

c Easily cut to the desired size.

For the distribution in a single row of automatic switches with a total of 12 modules.

1 2

3 4

Blanking plate

No. of modules Reference Length (mm)

6 ATP6/DTM 108

24 ATP24/DTM 432

Cut to size ATP/UND 1100

Distribution bars

No. of barsNo. of poles

per barReference Figure No.

1 12 BDS 1/12 1

2 6 BDS 2/6 2

3 4 BDS 3/4 3

4 3 BDS 4/3 4

03_025_037_EN.indd 3603_025_037_EN.indd 36 2/4/08 12:48:022/4/08 12:48:02

3/37

03_025_037_EN.indd 3703_025_037_EN.indd 37 2/4/08 12:48:042/4/08 12:48:04

1 2 3 4 65

1112 10 9 8 7

3/38

POLYMEL polyester monobloc enclosures

5 Enclosure with a tempered glass transparent door, maintaining the IP66 and IK08 (5J) degrees of protection.

1 The built-in canopy protects the door and the sealing gasket.

9 Depth adjustable mounting plate supports with positions every 12.5 mm.

03_038_039.indd 3803_038_039.indd 38 21/2/08 10:23:1021/2/08 10:23:10

3/39

2 Wall fixing from the outside with stainless steel or polyester wall brackets.

3 The fixing strips, notched every 25 mm, located at the back of the enclosure allow direct attachment of mounting rails or other devices, thus reducing assembly time.

6 The lock system is located outside the sealed area to maintain the IP66 degree of protection.

4 Four moulded bosses on the inside of the door help to assemble accessories. For maximum usable space, the door has a grid pattern for centring components. Door opening more than 180°.

12 Self-ventilation windows at the rear of the enclosure.

10 Direct wall fixing with a plug to maintain the double insulation and watertightness.4 inserts at the back for fixing the mounting plate.

11 Reversible polyester internal door with grid pattern for industrial control.

7 Interior hinges fixed into the door. The built-inpolyurethane sealing gasket guarantees IP66.

8 Ventilation louvers provide natural ventilation of the interior of enclosure, thus preventing condensation.

03_038_039.indd 3903_038_039.indd 39 21/2/08 10:23:1221/2/08 10:23:12

3/40

POLYMEL Polyester enclosuresIP66 (EN 60529)

PLM-75 PLM-75/CME

Hot-press moulded fibreglass-reinforced polyester enclosure, in grey RAL-7032.

Construction specifications

c Body of one single piece: monobloc.

c Fully reversible.

c Intended for use in both indoor and outdoor environments.

c A wide range of accessories enabling use in distribution, control and

measurement panels for industrial and infrastructure facilities.

c Standard double bar lock or three-point lock with handle (without insert).

Technical specifications

c Conforms to general rules for empty enclosures established in IEC and EN 62208.

c IP66 conforming to IEC 60529 (EN 60529).

c High resistance to mechanical impacts IK10 (20 J) conforming to IEC and EN 62262.

c Self-extinguishing, conforming to IEC 60695-2-1 (960°).

c Extreme operating temperatures from –50 to +150 ºC.

c Suitable for double insulation profiles conforming to IEC 60439-1 (EN 60439-1).

c Resistant to corrosion.

03_040_050_EN.indd 4003_040_050_EN.indd 40 2/4/08 12:50:102/4/08 12:50:10

3/41


* PLM-32 model in polycarbonate.

(1) Four-point locking system.



Plain Transparent door door

Plain door Mounting plates

Adjustable plate

support

Modular chassis

Internal door

No. of locks

Plain Transparent door door

Height(A)

Width(B)

Depth(C) Standard double bar lock

Three-point lock with handle (without insert)

Withinsulating mounting

plate MetalInsu-lating

Microper-forated Universal

310 215 160 PLM-32* PLM-32/KT* 1 - - PLM-32MB - - -

308 255 160 PLM-3025 PLM-3025/KT 2 - - PLM-3025MB -

430 330 200 PLM-43 PLM-43/KT 2 PLM-43/CME PLM-43 KT/CME PLM-43MB





1056 852 350 PLM-108 (1) PLM-108KT (1) 1 - - PLM-108MB

03_040_050_EN.indd 4103_040_050_EN.indd 41 2/4/08 12:50:132/4/08 12:50:13

3/42

PLM-32...108

PLM-3025


Dimensions (mm)

5 C

N

HRJ

M8

M8

B

Ø 8

D

A E

G

I

F H

16

Q

ML

I

K

P

Ø 8

PLM-… ENCLOSURE DIMENSIONS (EXCEPT PLM-3025)

Reference PLM-...

32 43 54 64 75 86 108

A 310 430 530 647 747 847 1056

B 215 330 430 436 536 636 852

C 160 200 200 250 300 300 350

D 310 280 380 480 580 680 864

E 215 200 300 300 400 500 694

F 270 380 480 580 680 780 980

G 170 260 360 360 460 560 760

H 225 325 425 525 625 725 925

I 125 225 325 325 425 525 725

J 275 375 475 575 675 775 975

K 75 150 250 250 350 450 650

L 8 13 13 13 15 15 15

M 144 181 181 228 278 278 327

N 2.3 2.7 2.9 2.9 3 3 4

P 132 179 279 279 379 479 684

Q 129 168 168 212 261 261 304

R 186 247 347 388 487 587 776

03_040_050_EN.indd 4203_040_050_EN.indd 42 2/4/08 12:50:142/4/08 12:50:14

355 165

200405

800

130

200

160100

160100165

251

398/635148

185

3/43

For the protection of cabling of outdoor installations, distribution panels for campgrounds, leisure harbours, etc. at which it is necessary to maintain a distance between the installation and the floor. Manufactured with fibreglass-reinforced polyester.

c Steel frame for fixing to the floor.

c Easy installation.

c High impact resistance.

Floor fixing using a frame (1)

Fixing to the enclosure

Floor-mounting pillar

PLM-54 SFS/PLM

PLM-64

ReferenceFor attachment to enclosures

(1) Frame supplied

For the lateral or vertical coupling of two enclosures.

c Made of fibreglass-reinforced self-extinguishing polyester.

c Sealing gasket built in, which guarantees the IP66 degree of protection.

c Mounting with screws (included in the standard supply).

Enclosure fastening ties

PLM-75 y 86 lateral BU/PLM

PLM-108 lateral BU-108/PLM

ReferenceType of couplingFor attachment to enclosures

POLYMEL Composition accessories

03_040_050_EN.indd 4303_040_050_EN.indd 43 2/4/08 12:50:142/4/08 12:50:14

15H1

V2H2

V1

8*

* For PLM-32 modeland PFI/PLM

3/44

Plain polyester cable entry plates, with sealing gasket and fastening hardware.

Cable entry plate

PLM-75/86/108 TLA-4420

PLM-108 TLA-6420


Composition accessories

Wall fixing can be done directly by drilling the back of the enclosure or with the PF/PLM polyester brackets or PFI/PLM stainless steel brackets. The brackets are mounted from the exterior to the back of the enclosure, using inserts and M8 screws (included in the standard supply).

Model PLM-32 is mounted using self-tapping screws.

The fixing pieces can be positioned vertically or horizontally.

The set is not included in the standard supply of the enclosure.

PFI/PLM

PF/PLM PFI/PLM

Wall fixing

Insulated

For attachment to enclosures

Stainless steel

Reference Horizontal position Vertical position

Fixing centres (mm)

Height (H1) Width (H2) Height (V1) Width (V2)

PLM-32 PF/PLM-32 - 247 239 334 152

PLM-3025 PF/PLM - 275 355 410 220

PLM-43 PF/PLM PFI/PLM 355 360 490 225

PLM-54 PF/PLM PFI/PLM 455 460 590 325

PLM-64 PF/PLM PFI/PLM 555 465 690 330

PLM-75 PF/PLM PFI/PLM 655 565 790 430

PLM-86 PF/PLM PFI/PLM 755 665 890 530

PLM-108 PF/PLM PFI/PLM 955 885 1090 750

POLYMEL

03_040_050_EN.indd 4403_040_050_EN.indd 44 2/4/08 12:50:162/4/08 12:50:16

B

A

3/45


Allows the enclosure to be fixed to concrete, wood or aluminium posts up to diameters of 675 mm.

c For exterior installations, provisional works or fairs, public lighting panels, etc.

c Galvanised steel fixing loop and profiles.

c Profiles attach to the back of the enclosure using M8 screws in the inserts (included in the standard supply).

c Recommended maximum weight of the installation: 100 kg.

Post fixing set

PLM-43 SFP-300

PLM-54 and PLM-64 SFP-400

PLM-75 SFP-500

PLM-86 SFP-600

PLM-108 SFP-800


Internal door set in fibre-glass reinforced polyester, except model PI-3025/PLM, made of sheet steel finished with polyester-epoxy RAL-7032 paint.

Insulating door specifications:

c Self-extinguishing.

c Grid pattern on the inside of the door for alignment of equipment.

c Quick locking through 1/4 turn sealable screws.

c Door opens in both directions.

C

D

* Plain internal door, dimensions A and B corresponding to the usable surface of the door.

Internal doors

PI-3025/PLM* 248 165 62 76

PIP-43 315 205 152 26

PIP-54 415 305 152 26

PIP-64 515 305 194 32

PIP-75 615 405 244 32

PIP-86 715 505 244 32

PIP-108 850 650 269 37

Reference A B C D

POLYMEL

03_040_050_EN.indd 4503_040_050_EN.indd 45 2/4/08 12:50:172/4/08 12:50:17

3/46

Doors to be changed or repositioned on PLM enclosures.

c Made of fibreglass-reinforced self-extinguishing polyester in grey RAL-7032.

c For maximum usable surface, the plain door has a grid pattern for centring components.

c Door opening to > 180°.

Spare doors

PLM-3025 PUPLM-3025 KTPLM-3025







TransparentPlain

For attachment to enclosuresType of door


Locks up to PLM-86

Standard double bar lock, with zinc-alloy inserts, operation with LDB 5 or DBP wing key (conforming to DIN 43668).

Reference: CDB/PLM.

TRANSFORMING INSERT OF STANDARD LOCK INTO STANDARDISED VERSIONS

Specifications ReferenceType of key operation ref.

v 6 mm square lock LC-7 TC6/CRN



Triangle lock with ∆ 6.5 mm side LT-8 TT7/CRN

Triangle lock with ∆ 8 mm side LT-8 TT8/CRN

Handle lock with 405 key

TL/PLM

Handle lock with key 220

TL220/PM

Stainless steel padlocking

device (up to PLM 86) KPLM

Fixed wing lock CDB/PLM

Double bar wing

DBP

Locks for polyester enclosures

POLYMEL

03_040_050_EN.indd 4603_040_050_EN.indd 46 2/4/08 12:50:182/4/08 12:50:18

3/47


Four-point locks for PLM-108

Standard double-bar lock for model PLM-108 in its plain door and KT transparent door versions. Operation with LDB 5 key or DBP wing key (conforming to DIN 43668).

TRANSFORMATION FROM FOUR-POINT LOCK TO DIFFERENT TYPES OF LOCKS OR FOR ENCLOSURES


v 6 mm square lock LC-7 TC 6/PL



Triangle lock with ∆ 7 mm side LT-8 TT 7/PL

Triangle lock with ∆ 8 mm side LT-8 TT 8/PL

Padlocking device BC/PL

STANDARD TRANSFORMATION FOR PLM-108 ENCLOSURE RETRACTABLE HANDLE LOCK WITH DIFFERENT TYPES


Double bar lock LDB 5 TEDB/PL

v 6 mm square lock LC-7 TEC 6/PL



Triangle lock with ∆ 7 mm side LT-8 TET 7/PL

Triangle lock with ∆ 8 mm side LT-8 TET 8/PL

Lock with key type 405 TEL/PL

Key-operated Lock

Reinforced type TER/PL

Lock with JIS key

TEL-JIS/PL

Lock with FAC key

TEL-FAC/PL

Manual lock TEM/PL

Handle without lock TE/PL

Padlocking device

BCME/PL

Handle for PLM-108 TEM/PL

LOCKS (INSERTS) FOR PLM...CME ENCLOSURES


Double bar lock LDB 5 TDB/PLD

Triangle lock with ∆ 8 mm side LT-8 TT7/PLD

Lock with key type 405 TCL/PLD

Key-operated Lock TLR/PLD

Reinforced type

Key-operated Lock

TJIS/PLD

Padlock lock

BCME/PL

Manual lock TEM/PLD

PLM... CME locks

POLYMEL

Standard handle locks without insert in models PLM… CME.

03_040_050_EN.indd 4703_040_050_EN.indd 47 2/4/08 12:50:212/4/08 12:50:21

3/48


Metal

Insulated

Perforated Universal

Bakelite Polyester

Height(A)

Width(B)

P S ReferenceThickness

(mm)Weight

(kg)Reference

Thickness(mm)

Weight(kg)

ReferenceThickness

(mm)Weight

(kg)Reference

Thickness(mm)

Weight(kg)

Reference D E

310 215 265 150 MM-32 2 0.6 MB-32 4 0.2 MP-32 4 0.3 MF-32 2 0.3 MR-32 255 154

308 255 265 200 MM-3025 2 0.6 MB-3025 4 0.3 MP-3025 4 0.4 MF-3025 2 0.5 MR-3025 253 228

430 330 365 250 MM-43 2 1.6 MB-43 4 0.5 MP-43 4 0.7 MF-43 2 1.5 MR-43 348 251

530 430 465 350 MM-54 2 2.5 MB-54 4 0.9 MP-54 4 1.2 MF-54 2 2.4 MR-54 450 351

647 435 565 350 MM-64 2 3.1 MB-64 4 1.1 MP-64 4 1.4 MF-64 2 3 MR-64 555 351

747 536 665 450 MM-75 2 4.6 MB-75 4 1.7 MP-75 4 2.1 MF-75 2 4.3 MR-75 645 451

847 636 765 550 MM-86 2.5 9.9 MB-86 4 2.3 MP-86 5 3.8 MF-86 2.5 9 MR-86 750 551

1056 812 965 750 MM-108 2.5 16.9 MB-108 5 5.7 MP-108 5 6.5 MF-108 2.5 16 MR-108 945 751

Mounting accessoriesPOLYMEL

A complete range of mounting plates comprised of 4 versions able to provide all the mountings required for this installation system.

c Metal plates of galvanised sheet steel.

c Microperforated plates made of galvanised sheet steel with 3.6 mm ∅ holes, 12.5 mm apart.

c Universal perforated plates for fast fixing of equipment, made of zinc steel.

c Insulating bakelite or polyester plates.

E

D

15

12,5

P

S

10,5 10,5

12,5 25 25

2525

20

B-75

A-7

5

ø6,5

ø8,5

P

S

12,5

P

S

B-75

A-7

5

12,5

12,5

12,5

12,5

ø3,6

P

S

Metal BakelitePerforated UniversalMetal

Bakelite

Microperforated

Universal perforated

Mounting plates

Polyester

Polyester

03_040_050_EN.indd 4803_040_050_EN.indd 48 2/4/08 12:50:262/4/08 12:50:26

B

A

1126 mm

30 30

1515

3/49


Supports designed to fit 200, 250, 300 and 350 mm deep enclosures.

With positioning notches along its entire length for depth adjustment of the mounting plate every 12.5 mm.

c Made of galvanised sheet steel.

c Quick fixing to the enclosure.

Adjustable plate support

PLM-43 and 54 DPLM-200 156 94

PLM-64 DPLM-250 200 100

PLM-75 and 86 DPLM-300N 250 100

PLM-108 DPLM-350 306 106

For attachment to enclosures Reference A B

Fixing accessories for universal plates

Length(mm)

Fixing nut Fixing screw with washer

Thread typePackaging Packaging

M3 TFP 3 100 - - -

M4 TFP 4 100 TOR 10/4 A 10 100

TOR 16/4 A 16 100

M5 TFP 5 100

TOR 12/5 A 12 100

TOR 18/5 A 18 100

M6 TFP 6 100

TOR 12/6 A 12 100

TOR 18/6 A 18 100

03_040_050_EN.indd 4903_040_050_EN.indd 49 2/4/08 12:50:272/4/08 12:50:27

25

3/50


c Insulating support and self-tapping screw for quick fixing of L brackets and 35 mm symmetrical rails (Ref. TCO/PLM).

c Insulating support and M6 inserted bolt for quick fixing of L brackets and 35 mm symmetrical rails (Ref. TCO-M6/PLM).

Rail fixing set

TCO/PLM Self-tapping

TCO-M6/PLM M6

Type of screwReference

35 mm symmetrical rails to support equipment, specially adapted to the width of the enclosures.

Fixing at the back of the enclosure using the TCO/PLM set.

35 mm symmetrical rail

PLM-32 CO-200/PLM 180

PLM-43 CO-300/PLM 280

PLM-54 and 64 CO-400/PLM 380

PLM-75 CO-500/PLM 480

PLM-86 CO-600/PLM 580

PLM-108 CO-800/PLM 795

For attachment to enclosures Reference Width

TCO/PLM

03_040_050_EN.indd 5003_040_050_EN.indd 50 2/4/08 12:50:292/4/08 12:50:29

3/51

Current distribution accessoriesPOLYMEL

Clip in fasteners to be installed directly on 19” racks and on slotted MR mounting plates.

Reference: GCR.

GCR ties


Adjustable ties

White BlackL ∅

minimum∅

maximum

M

Reference Use

LZ25100 LN25100 100 2.5 1.6 22

LZ25200 LN25200 200 2.5 1.6 49

LZ35150 LN35150 150 3.5 1.6 35

LZ35200 LN35200 200 3.5 1.6 49

LZ35300 LN35300 300 3.5 1.6 75

LZ46150 LN46150 150 4.6 1.6 36

LZ46200 LN46200 200 4.6 1.6 49

LZ48270 LN48270 270 4.8 1.6 73

LZ46390 LN46390 390 4.6 1.6 109

LZ76390 LN76390 390 7.6 4.7 108

To tighten and cut to size the adjustable ties. They facilitate wiring and save time, preventing the packets of cables from loosening.



Tightening tools

Reference

MARK3 2.5 ÷ 4.8


Reference

MARK20 2.5 ÷ 4.8

MARK21 4.6 ÷ 7.6


03_051_062_EN.indd 5103_051_062_EN.indd 51 2/4/08 12:51:542/4/08 12:51:54

3/52


To use with soft materials: 7 mm Ø hole, or hard materials: 8 mm Ø hole. Ties are attached up to 9 mm width. Material: black 6.6 nylon.

Ref.: LOK01.

Stud


Tie fixing support


tiesC

KR6 12 18 9 M4 2.5 ÷ 4.8

KR8 14.5 25 12 M6 2.5 ÷ 7.6


Locking clips

Reference

SFC1 6 3.2 1

SFC2 6 1 2

FigureMax. panel

thickness mm∅ Perforation

mm

SFC2 SFC1

Fig. 1 Fig. 2

03_051_062_EN.indd 5203_051_062_EN.indd 52 2/4/08 12:51:552/4/08 12:51:55

adhesive support

3/53



Support heads


tiesC

FH18 7.1 13.3 4 M4 2.5

FH30 9.5 17.9 4.7 M5 3.5

FH50 11.3 22.2 6.2 M6 4.7




tiesD

MB3A 19.1 19.1 4.8 3.2 13.2 2.5 ÷ 3.5

MB4A 28.5 28.5 5.5 4 20.2 2.5 ÷ 4.8


Tie fixing support

Reference

LKC 2.5 7.6 M5


ties mm

03_051_062_EN.indd 5303_051_062_EN.indd 53 2/4/08 12:51:572/4/08 12:51:57

3/54


2 versions, fixed and graduated, ∅ from 5 to 25.4 mm. Material: black 6.6 nylon.


Reference∅ A

min. - max.B D EC

NX1 5 3.5 1 6.2 13.7

NX3 8 3.9 1 9.4 20.5

NX5 12 3.9 1 9.4 24

NX8* 14.3 ÷ 15.8 4 1.3 12.6 32

NX11 17.4 ÷ 20 4 1.3 12.6 37

NX14 22.2 ÷ 25.4 4.3 1.5 16 45


NX 1-3-5 NX 8-11-14

Covers the head of the tie in its end, thus obtaining neater cabling. Material: 6.6 nylon.


Reference

LKM/HE 2.5 7.6 M5


ties mm

03_051_062_EN.indd 5403_051_062_EN.indd 54 2/4/08 12:51:582/4/08 12:51:58

Ø A

Ø B

3/55


Insulating membrane glands made of PVC with entry that can be adjusted for cables.



Capacity

ECPC-3 1 25 21.5 18 5 3.2 13 5 to 18 Pg 9 to 11

ECPC-5 1 33 29.5 26 5 3.2 20 5 to 26 Pg 9 to 16

ECPC-6 1 43 38.5 36 5 3.2 22 5 to 36 Pg 9 to 21

ECPC-9 2 70 63 60 28 3 20 28 to 60 Pg 21 to 48

ECPC-15 2 98 90 87 28 3 23 28 to 87 Pg 21 to 48


Fig. 1 Fig. 2


Protective sleeves


PC-1 15.2 12.7 Pg 9

PC-2 18.6 16 Pg 11

PC-3 20.4 17.8 Pg 13.5

PC-4 22.5 19.8 Pg 16

PC-5 28.3 25.3 Pg 21

PC-6 37 33.6 Pg 29

PC-7 47 43 Pg 36

03_051_062_EN.indd 5503_051_062_EN.indd 55 2/4/08 12:51:592/4/08 12:51:59

3/56


Øexterior

SteelFlexible


Protective sleeves

Adjustable membrane

glandsPlain plugs


Flexible steel with

PVC

Cables inserted*Ø interior To the perforationsTo the tubes

4 EC-1 to EC-7

Pg 9 15.2 12.7 12.4 12 11.1 6 2.5 - - 16 14 ECPC-3 to ECPC-6 PC-1 - -

ECN-5 to ECN-10

10 4 2.5 EC-2 to EC-7 EC-1



EC-3 to EC-7 EC-3


ECN-5 to ECN-10

EC-4 to EC-7


ECN-5 to ECN-10

EC-5 to EC-7 EC-5



95 35 25 16 EC-6; EC-7 EC-6 TC-5


150 ECN-7; ECN-10 ECN-6

185 35 EC-7 EC-7


300 ECN-10

95 70 ECPC-9; ECPC-15

Pg 42 54 50 48 48 47 - 120 95 70 55 52.5 ECN-10 - - -

120 95 ECPC-9; ECPC-15

Pg 48 60 56 54.2 52.5 51.4 - 150 150 120 61 58 ECN-10 - - -



1 2 3 4


No. of conductors



Ø perforations to

Desig-nation

03_051_062_EN.indd 5603_051_062_EN.indd 56 2/4/08 12:52:002/4/08 12:52:00

3/57


Base of safety terminals made of black matte self-extinguishing polyamide-6; terminal of brass MS-58.







Reference

S.04 1 × 4 30 20 13 21 4

S.06 1 × 6 33 25 16 24 7

S.10 1 × 10 38 28 16 28 6

S.16 1 × 16 42 32 19 32 9

S.25/35 1 × 35 46 38 23 34 11

S.50 1 × 50 52 45 27 40 15

S.70 1 × 70 55 50 30 40 15

S.95/100 1 × 100 58 54 33 40 20


Section m/m2 A B C D E


Number of terminals section in mm2

Earth and neutral bypass terminal blocks with insulated plinth.



RBLZ/21656* 216 mm2 + 56 mm2

RBLZ/21686 216 mm2 + 86 mm2

RBLZ/216146 216 mm2 + 146 mm2

RBLZ/216296 216 mm2 + 296 mm2

Reference

03_051_062_EN.indd 5703_051_062_EN.indd 57 2/4/08 12:52:002/4/08 12:52:00

1 2

3/58





Reference

BBH-29 6-50 -

BBH-29C* 6-50 -

BBH-30 10-95 -

BBH-31 16-150 -

BBH-32 50-240 -

BBH-29D 6-50 6-50

BBH-29DC* 6-50 6-50

BBH-30D 10-95 10-95

BBH-31D 25-150 16-150

BBH-32D 95-240 5-240

Main section mm2 Bypass section mm2

Reference

BBH-29P 6-50 -

BBH-29PC* 6-50 -

BBH-29DP 6-50 6-50

BBH-29DPC* 6-50 6-50



BBH-29 BBH-29D

BBH-29P BBH-29DP



ReferenceCable bypass section

(mm2)Plate thickness (mm) Figure

BPCH 516 1.5 to 16 5 2

BPCH 550 1.5 to 50 5 2

BPCH 5120 16 to 120 5 2

BPCH 1016 1.5 to 16 10 1

BPCH 1050 1.5 to 50 10 1

BPCH 10120 16 to 120 10 1

03_051_062_EN.indd 5803_051_062_EN.indd 58 2/4/08 12:52:042/4/08 12:52:04

35590

7066

3/59

Lighting accessoriesPOLYMEL

Compact lamp

Specifications TensionPlugReference

Lamp fixed with a magnet or

on 35 mm symmetric LAM-75 220 V/16 A 220 V/50 Hz

DIN rail.

Lamp fixed on a 35 mm

symmetric DIN rail. LAC-75 220 V/16 A 220 V/50 Hz

Lamp fixed with a magnet

or on 35 mm symmetric LAM-75/120 120 V/15 A 120 V/60 Hz

DIN rail.


symmetric DIN rail. LAC-75/120 120 V/15 A 120 V/60 Hz

Compact fluorescent lamps, designed especially for use in electronic enclosures. May be fixed with a magnet.

c Connection voltage 220 V/50 Hz.

c Consumption 11 W.

c Connection/disconnection switch.

c 200 V/16 A socket with earthing.

c Maximum ambient temperature 60 °C.

c Lighting output = 75 W bulb.

Magnetic-fixing flat lamps equipped with energy efficient light bulbs, with or without a plug.

c Electronic ballast.

c Power: 11 W.

c Luminosity: 900 lm.

c Lifespan: 10000 h.

c Plastic casing UL94 V0.

c IP20.

c Class I.

Slimline lamp

Reference Plug Socket Approval

LAMS75 AC 230 V/16 A SCHUKO VDE

LAMX75 AC 230 V/- - VDE

LAMU75 AC 120 V/15 A USA UL

03_051_062_EN.indd 5903_051_062_EN.indd 59 2/4/08 12:52:062/4/08 12:52:06

396

67

100

500

3/60

Lighting accessoriesPOLYMEL

Dual lamp

1

2

3

4

Specifications Support fixing Figure Reference Tension

Motion-activated

Magnetic, using screws LAMDP 220 V/56 Hz

and/or (1) 35 DIN rail 1 LAMDP 120 120 V/60 Hz

On/off switch with the possibility Magnetic, using screws LAMIN 220 V/50 Hz

of connection of door switch and/or (1) 35 DIN rail 2 LAMIN 120 120 V/60 H

Mobile lamp, connection Adhesive or screws

LAMPO 220 V/50 Hz

via cable 3 LAMPO 120 120 V/60 Hz

Support for LAMDP, LAMIN, Adhesive or screws

LAMPO lamp 4 SOLAM

(1) DIN rail not provided.

Light fixtures designed especially for use in electronic enclosures with various possibilities for fixing and operating.

c Energy efficient electronic lamp E27, 20 W, 220-240 V/50-60 Hz or 120 V/60 Hz.


c Fixed models connection via 2.5 mm2 terminal strip and the mobile model via cable.

c Degree of protection IP20.

c Insulation class II.

c Conforming to EN 55014 and EN 50082-1.

Incandescent lamp designed especially for use in electronic enclosures.

c Connection voltage 220 V/50-60 Hz.

c Consumption 60 W.


c Terminal connection entry.

Incandescent lamp

Reference

LAI/OL 68

03_051_062_EN.indd 6003_051_062_EN.indd 60 2/4/08 12:52:072/4/08 12:52:07

3/61

Natural ventilation accessoriesPOLYMEL

To connect the inside of the enclosure with the exterior atmosphere and prevent condensation. Can be fixed onto the outside, Ref.: VM-25 and VM-27 or onto the internal sides connected with the rear self-ventilating windows of the POLYMEL enclosures, Ref.: VM-35.

VM-25 VM-27

VM-35

Ventilation devices

VM-25 For coupling to the outside of all polyester enclosures

VM-27

VM-35 For coupling to the interior of POLYMEL enclosures

SpecificationsReference

To remove condensation water.

Mounted on the ∅ 9 mm housing on the inside of the bottom of the enclosure. Degree of protection IP55.

Purging device

VEA-9 For attachment to all enclosures


Rear blanking plates in insulating material to protect against unwanted elements entering into the self-ventilating window of the enclosure.

Not included in standard supply with the enclosure except for model 108 which has it built in.

Rear blanking plates

PLM-32 CE-PLM/A

PLM-43 and 54 CE-PLM/B

PLM-64, 75 and 86 CE-PLM/C


03_051_062_EN.indd 6103_051_062_EN.indd 61 2/4/08 12:52:092/4/08 12:52:09

174

188 22 278 40

234

3/62

Complementary accessoriesPOLYMEL

Dodge-type brass nuts designed to be incorporated into the bosses of PLM enclosures.

Expandable nuts

M5 PLM-43 and 54 TEX 5


M8 For the back of the enclosure TEX 8

ReferenceSpecifications For attachment to enclosures

PP-A models made of thermo-plastic in grey RAL-7035.

c Fixed with adhesive tape or screws.

For holding A4 or A5-sized plans.

Document pocket

Ref.: PP-A5 Ref.: PP-A4

Plan size

A4 PP-A4

A5 PP-A5

Reference

Insulated

TEX 8 TEX 6 TEX 5

03_051_062_EN.indd 6203_051_062_EN.indd 62 2/4/08 12:52:102/4/08 12:52:10

3/63

c Rigid structure made of galvanised steel.

c Insulating cover and frame in self-extinguishing material in RAL-7035.

Quick mounting, without the need for screws.

c System for identifying circuits included in the standard supply.

c Earth and neutral bypass terminal blocks. Ref.: RBLZ/21656 (included in

standard supply).

PLM-64/KT + DLA-48P

POLYMEL Applications

Distribution chassis set for modular equipment, Ref.: DLA-... with a distance between the 35 mm symmetric profile and the cover, which is adjustable as needed by the customer from 40 to 85 mm.

Dinimel DLA distribution chassis

03_063_067_EN.indd 6303_063_067_EN.indd 63 2/4/08 12:52:592/4/08 12:52:59

3/64

* Models DLA-48P, 66, 88, 84 and 112.


Dimensions (mm)

DLA-24 DLA-48 DLA-48P DLA-66 DLA-88

DLA-84 DLA-112 DLA-240

* For PLM.../CME enclosures with three-point locks, factory assembly

To be coupled to enclosures*

Reference

Plain door Transparent door No. of rowsQuantity

No. of 18 mm modules

Distribution of rows

Automatic rail

No. of plates A B

Dimensions

C D min. E min.

PLM-3025 PLM-3025/KT DL/PLM18 2 2 18 - - - - - -

PLM-43 PLM-43/KT DLA-24 2 2 24 - 216 115 137 38 88

PLM-54 PLM-54/KT DLA-48 3 3 48 - 288 90 112 38 88

PLM-64 PLM-64/KT DLA-48P 3 3 48 - 288 140 170 80 130

PLM-75 PLM-75/KT DLA-66 4 3 66 1 395 115 145 129 179

PLM-75 PLM-75/KT DLA-88 4 4 88 - 395 115 145 129 179

PLM-86 PLM-86/KT DLA-84 4 3 84 1 504 165 195 129 179

PLM-86 PLM-86/KT DLA-112 4 4 112 - 504 165 195 129 179

PLM-108 PLM-108/KT DLA-240 6 6 234 - 704 115 146 170 220

03_063_067_EN.indd 6403_063_067_EN.indd 64 2/4/08 12:53:002/4/08 12:53:00

3/65

Insulating cover in self-extinguishing material in RAL-7035 to protect non-modular equipment. Height: 150 mm (1 row).

Plain Dinimel DLA cover

DLA-24 CTL300/DLA 256

DLA-48 and 48P CTL400/DLA 356

DLA-66 and 88 CTL500/DLA 456

DLA-84 and 112 CTL600/DLA 555

DLA-240 CTL800/DLA 755

ReferenceReferenceTo be coupled to chassis


Mounting plate in galvanised steel for fixing non-modular equipment. Height: 150 mm (1 row).

Dinimel DLA mounting plate

DLA-24 PMP300/DLA 215

DLA-48 and 48P PMP400/DLA 315

DLA-66 and 88 PMP500/DLA 415

DLA-84 and 112 PMP600/DLA 514

DLA-240 PMP800/DLA 714

WidthReferenceTo be coupled to chassis

Blanking plate of self-extinguishing insulating material for total or partial coverage of the windows for automatic switches. Easily cut to the desired size.

Blanking plate

ATP6/DTM 108 6

ATP24/DTM 432 24

ATP/UND 1100 Cut to size

No. of modulesLength (mm)Reference

03_063_067_EN.indd 6503_063_067_EN.indd 65 2/4/08 12:53:012/4/08 12:53:01

3/66


Number of terminals 3 section in mm2

Earth and neutral bypass terminal blocks with insulating plinth.



RBLZ/21656* 216 mm2 + 56 mm2

RBLZ/21686 216 mm2 + 86 mm2

RBLZ/216146 216 mm2 + 146 mm2

RBLZ/216296 216 mm2 + 296 mm2

Reference



1 2

3 4

Distribution bars

No. of bars No. of poles per bar Reference Figure No.

1 12 BDS 1/12 1

2 6 BDS 2/6 2

3 4 BDS 3/4 3

4 3 BDS 4/3 4

03_063_067_EN.indd 6603_063_067_EN.indd 66 2/4/08 12:53:012/4/08 12:53:01

3/67


Due to the quality of the plastic materials and their constructive characteristics, POLYMEL enclosures are suitable for panels in installations subjected to contact with chemical agents and harsh environments, usually, for example, in the petrochemical, cement making, etc. industries.

Their resistance to corrosion and UV rays permits POLYMEL enclosures to be adapted to panels in exterior installations subjected to long exposures to the sun: winter sport stations, installations close to the sea, etc.

POLYMEL enclosures in leisure facilities

Their high degree of protection (IP66) and their high resistance to impacts and temperature make POLYMEL enclosures particularly ideal for industrial installations subjected to processes with frequent water projection, such as the paper-making and agri-food industries or automobile washes.

POLYMEL enclosures in interior industrial installations

POLYMEL enclosures in exterior industrial installations

03_063_067_EN.indd 6703_063_067_EN.indd 67 2/4/08 12:53:052/4/08 12:53:05

1 2 3 4 5 6 7

10 814 13 12 11 9

3/68

5 Detail of fixing the glass to the inside of the door.

1 Wall fixing brackets.

PLA polyester modular enclosures

8 Detail of bosses on the doors, back and lower part of the enclosure for fixing of various materials.

12 Mounting plate fixing support, adjustable every 25 mm.

03_068_069.indd 6803_068_069.indd 68 22/2/08 18:35:3022/2/08 18:35:30

3/69

7 The locking system is outside the sealed area, which guarantees the IP over time. Handle lock with detail of the cover that hides the lock device.

6 Ribbed door to make fixing of posters difficult. Likewise, this uneven surface makes the door thicker and also improves the robustness of the enclosure.

4 Detail of 120º hinge with easily removable stainless steel safety pin. Seal that guarantees IP65 watertightness.

3 The enclosures with canopies allow self-ventilation of the enclosure, preventing condensation and maintaining the IP54.

2 2-point locking system (up to 750 mm height) or 4-point locking system (from 1,000 mm height).

11 Door retainer.

14 Metal, insulating or universal mounting plates to be fixed directly to the back of the enclosure or by using adjustable supports.

10 Door opening to 180º, which improves accessibility to the interior of the enclosure with plinth and canopy. The plinth-type base allows direct floor fixing.

9 Anti-vandalism reinforcement.

13 PLAZ... enclosures with open plinth-type bottom for easy cable entry.

03_068_069.indd 6903_068_069.indd 69 22/2/08 18:35:3222/2/08 18:35:32

3/70

CONSTRUCTION SYSTEMS

PLA 1054 PLA 1054 T PLAZ 1054 PLAZ 1054 T

PLA 1054 KT PLA 1054 TKT PLAZ 1054 KT PLAZ 1054 TKT

PLA 1054 R PLA 1054 TR PLAZ 1054 R PLAZ 1054 TR

PLA 1054 P PLA 1054 TP PLAZ 1054 P PLAZ 1054 TP

PLA 1054 PKT PLA 1054 TPKT PLAZ 1054 PKT PLAZ 1054 TPKT

PLA 1273 PR PLA 1273 TPR PLAZ 1273 PR PLAZ 1273 TPR

Plain doorPLA/PLAZ...

Transparent doorPLA/PLAZ...KT

Ribbed doorPLA/PLAZ...R

Plain front andback doorsPLA/PLAZ...P

Transparent front door andplain back doorPLA/PLAZ...PKT

Ribbed front and back doorsPLA/PLAZ...PR

Closed topSelf-ventilated top with

canopy

Enclosures with open plinth-type baseEnclosures with closed baseTable of formation references

General table with the construction systems on the horizontal axis and the various versions of doors on the vertical axis, offering apanoramic view of the formation of all the possibilities of references.

Closed topSelf-ventilated top with

canopy

PLA... PLA...T PLAZ... PLAZ...T

120° 120°

IP65

Door opening

Degree of protection IP54

120°

IP54

180°

IP54

EXAMPLES OF FORMING REFERENCES

Height: 1,000 Width: 500 Depth: 420

Top and bottom closed, with transparent door.

Ref.: PLA 1054 KT

Height: 1,200 Width: 750 Depth: 320

Self-ventilated top with canopy, open plinth-type bottom, ribbed front and back doors.

Ref.: PLA Z 1273 TPR

With base

Construction systems

Dimensions (mm)

Closed Open, plinth-type Height Width DepthExamples of enclosures

PLA -

- PLAZ XX XX X

PLA - 10 5 4

- PLAZ 12 7 3

03_070_083_EN.indd 7003_070_083_EN.indd 70 5/3/08 11:20:505/3/08 11:20:50

3/71

The table showing each of the dimensions (height, width and depth) determines the digits to use when forming the references.The tables in grey and blue have to do with to the examples of the reference formation table.

Height Width Depth


5 00

5 00

7 50 3 20

7 50

10 00

10 00

12 50 4 20

12 50

15 00

Door versionWith top

ClosedSelf-ventilatedwith canopy Plain Transparent Ribbed Plain front cover and back Ribbed front cover and back

- T - KT R P PR

- - - KT - - -

- T - - - - PR

03_070_083_EN.indd 7103_070_083_EN.indd 71 5/3/08 11:20:525/3/08 11:20:52

3/72


c Resistance to the main chemical agents and corrosive environments.

c Stabilised against UV rays.

c Door reversibility with opening to 120º, with max. admissible load of 30 kg/m2.

c Lock outside of the sealed area, with a 2-point locking system up to 750 mm height, 4-point locking system from 1000 mm height.

c Interior of the enclosure equipped with bosses for M8 inserts. They allow direct fixing of mounting plates and/or the desired installation system, accessories, etc.




c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262).





PLA 1253

PLA . . . Polyester enclosures completely closedIP65 (EN 60529)

PLA 12123

Hot-press moulded fibreglass-reinforced polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).

03_070_083_EN.indd 7203_070_083_EN.indd 72 5/3/08 11:20:535/3/08 11:20:53

3/73

PLA. . . Completely closed polyester enclosuresIP65 (EN 60529)

Basic composition

c Enclosure with top and base completely closed.

c Sealing gasket.

c Plain, transparent or ribbed door.

c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to EN 62262.

c ..R model: ribbed door to make fixing of posters difficult and with “anti-lever” hinges.

c Back panel or door.

c Reversible door with 2 hinges up to 750 mm height, and 4 from 1000 mm height.

c Standard double bar lock, operated by key LDB5.

c Two-door enclosures have a central profile.

SELECTION TABLE FOR CLOSED POLYESTER ENCLOSURES

Height Width Depth No. of doors


500 500 320 1 PLA 553 PLA 553 R PLA 553 KT PLA 553 P PLA 553 PR PLA 553 PKT

420 1 PLA 554 PLA 554 R PLA 554 KT PLA 554 P PLA 554 PR PLA 554 PKT

750 320 1 PLA 573 PLA 573 R PLA 573 KT PLA 573 P PLA 573 PR PLA 573 PKT






































03_070_083_EN.indd 7303_070_083_EN.indd 73 5/3/08 11:20:555/3/08 11:20:55

3/74










c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262.





PLA. . .TPolyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)

Hot-press moulded, fibreglass-reinforced, self-ventilated polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).

PLA 1253T

03_070_083_EN.indd 7403_070_083_EN.indd 74 5/3/08 11:20:565/3/08 11:20:56

3/75

PLA. . .TPolyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)

SELECTION TABLE FOR CLOSED BASE, SELF-VENTILATED POLYESTER ENCLOSURES



500 500 320 1 PLA 553 T PLA 553 TR PLA 553 TKT PLA 553 TP PLA 553 TPR PLA 553 TPKT

420 1 PLA 554 T PLA 554 TR PLA 554 TKT PLA 554 TP PLA 554 TPR PLA 554 TPKT

750 320 1 PLA 573 T PLA 573 TR PLA 573 TKT PLA 573 TP PLA 573 TPR PLA 573 TPKT






































Basic composition

c Open top with canopy.

c Base completely closed.

c Sealing gasket.


c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to IEC and EN 62262.




c Standard double bar handle lock, operated by key LDB5.


03_070_083_EN.indd 7503_070_083_EN.indd 75 5/3/08 11:20:575/3/08 11:20:57

3/76










c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262.





PLAZ. . .Polyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)

PLAZ 1253

Hot-press moulded fibreglass-reinforced polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).

03_070_083_EN.indd 7603_070_083_EN.indd 76 5/3/08 11:20:575/3/08 11:20:57

3/77

PLAZ. . .Polyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)

Basic composition

c Closed top.

c Open plinth-type base.

c Sealing gasket.


c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to IEC and EN 62262.






SELECTION TABLE FOR POLYESTER ENCLOSURES WITH CLOSED TOP AND OPEN PLINTH-TYPE BASE



500 500 320 1 PLAZ 553 PLAZ 553 R PLAZ 553 KT PLAZ 553 P PLAZ 553 PR PLAZ 553 PKT

420 1 PLAZ 554 PLAZ 554 R PLAZ 554 KT PLAZ 554 P PLAZ 554 PR PLAZ 554 PKT

750 320 1 PLAZ 573 PLAZ 573 R PLAZ 573 KT PLAZ 573 P PLAZ 573 PR PLAZ 573 PKT






































03_070_083_EN.indd 7703_070_083_EN.indd 77 5/3/08 11:20:585/3/08 11:20:58

3/78










c High resistance to mechanical impacts IK10 (20 J) conforming to IEC and EN 62262.





PLAZ. . .TPolyester enclosures with self-ventilated top with canopy and open plinth-type baseIP54 (EN 60529)

PLAZ 7103T

Hot-press moulded, fibreglass-reinforced, self-ventilated polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).

03_070_083_EN.indd 7803_070_083_EN.indd 78 5/3/08 11:20:595/3/08 11:20:59

3/79

Basic composition

c Open top with canopies.

c Open plinth-type base.

c Sealing gasket.


c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to EN 50102.







SELECTION TABLE FOR POLYESTER ENCLOSURES WITH SELF-VENTILATED TOP WITH CANOPY AND OPEN PLINTH-TYPE BASE



500 500 320 1 PLAZ 553 T PLAZ 553 TR PLAZ 553 TKT PLAZ 553 TP PLAZ 553 TPR PLAZ 553 TPKT

420 1 PLAZ 554 T PLAZ 554 TR PLAZ 554 TKT PLAZ 554 TP PLAZ 554 TPR PLAZ 554 TPKT

750 320 1 PLAZ 573 T PLAZ 573 TR PLAZ 573 TKT PLAZ 573 TP PLAZ 573 TPR PLAZ 573 TPKT






































03_070_083_EN.indd 7903_070_083_EN.indd 79 5/3/08 11:21:005/3/08 11:21:00

A-1

50

A-1

50

B-150B-150

37.5 75

C-8

25

28.5

C

A260

28.521

25

A-2

55

C-140

C-42

B-95

A-9

5

A-9

5

B-95

1

4

2

1 1

4

2

1

1

C-170

A-2

00

25

A-1

50

B-150

B-120

C-1

25

37.5

C-1

40

B-205

M8

C-13

25

28.5

C

A260

28.521

25

A-2

55

C-140

C-42

B = 500 / 750

17 / 28*

B-95

A-9

5

A-2

53

285/535

A-1

50

B-150

B-120

C-1

25

75

C-1

40

B-205

M840

B =1000/1250

500/750

405 405/655

500

37

A-9

5

B-95A-2

53

285 285/535

1

4

2

3

1

3

1

1

1

4

2

1

3

311

1 1

4 4

1

25

C-170

A-2

00

3/80

FIG. 1

PLA...

FIG. 2

PLA...KT

PLA. . . Polyester enclosures completely closedIP65 (EN 60529)

Dimensions (mm)

03_070_083_EN.indd 8003_070_083_EN.indd 80 5/3/08 11:21:015/3/08 11:21:01

A-1

50

A-1

50

B-150B-150

B-120

C-1

25

B-120C

-125

37.5

B = 500 / 750

C-1

40

B-205

M8

75

C-8

25

28.5

C

A+

38

C-1

40

B-205

M8

B =1000/1250

500 500/750

405 405/655

260

28.5

21

25

A-2

55

C-140

C-42

40

23 / 28* 37

38

B-95

A-9

5

A-9

5

B-954

2

1

4

2

1

1

1

3

4

2

4

3

1

3

3

1

1 1

C-170

A-2

00

25

3/81

FIG. 1

PLA...T

1 Bosses on the back of enclosures starting with 1000 mm wide allow the fixing of partial mounting plates (see plates section). Bosses at the top and bottom are used for fixing depth adjustable supports, internal doors, 19” racks, etc.

In general, all bosses- including those on the sides and on the interior of the door- are prepared for M8 inserts Ref.: TEX 8 for fixing various material.

2 Bosses with M8 inserts equipped with studs for fixing the mounting plates.

3 Centres for floor or plinth fixing.

4 Dimensions of the door opening.

NOTE: in 1250 mm width enclosures, the left door is 500 mm and the right is 750 mm.

PLA. . .TPolyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)

* For mounting plates with reinforcement wing.

Dimensions (mm)

03_070_083_EN.indd 8103_070_083_EN.indd 81 5/3/08 11:21:015/3/08 11:21:01

B-150

A-1

50

A-1

50

37.5

A-1

50

B-150

75

C-42

C-8 260

25

A-2

55

C-140

A+

55

28.5

C

28.521

55

B-95

A-9

5

A-9

5

B-95

1

4

2

1

1

4

2

1

1

33

C-170

A-2

00

25

A-1

50A

-150

B-150

A-9

5

B-95

75

1

4

2

1

B-60

C-1

60

B =1000/1250

500 500/750

405 405/655

C-6

8

B-81

M840

37

6.5 6.5

3

44

3

25

C-42

C-8 260

25

A-2

55

C-140

A+

55

28.5

C

28.521

55

1

C-170

A-2

00

B-150

A-1

50

B-95

A-9

5

37.5

1

4

2

1

B-60

C-1

60

23 / 28*

M8

B = 500/750

C-6

8

B-81

6.5 6.5

3

3

3/82

FIG. 1

PLAZ...

FIG. 2

PLAZ...R

PLAZ. . .Polyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)

Dimensions (mm)

03_070_083_EN.indd 8203_070_083_EN.indd 82 5/3/08 11:21:015/3/08 11:21:01

B-95

A-9

5

A-9

5

B-95

B-150

A-1

50

37.5

B-60

C-1

60

23 / 28*

M8

B = 500/750

C-6

8

B-81

6.5 6.5

B-60

C-1

60

B =1000/1250

500 500/750

405 405/655

C-6

8

B-81

M840

37

6.5 6.5

A-1

50A

-150

B-150

75

C-42

C-8 260

25

A-2

55

C-140

A+

93

28.5

C

28.521

3855

1

4

2

1

1

4

2

1

1

3

44

3

3

3

C-170

A-2

00

25

3/83

FIG. 1

PLAZ...T

1 Bosses on the back of enclosures starting with 1000 mm wide allow the fixing of partial mounting plates (see plates section). Bosses at the top and bottom are used for fixing depth adjustable supports, internal doors, 19“ racks, etc.

In general, all bosses- including those on the sides and on the interior of the door- are prepared for M8 inserts Ref.: TEX 8 for fixing various material.

2 Bosses with M8 inserts equipped with studs for fixing the mounting plates.

3 Centres for floor or plinth fixing.

4 Dimensions of the door opening.

* For mounting plates with reinforcement wing.

NOTE: in 1250 mm width enclosures, the left door is 500 mm and the right is 750 mm.


Dimensions (mm)

03_070_083_EN.indd 8303_070_083_EN.indd 83 5/3/08 11:21:025/3/08 11:21:02

3/84

PLA Composition accessories

PVC frame with sealing gasket that permits lateral coupling of enclosures PLA or PLA...T.

They complement the MUPLA coupling frame for lateral union of enclosures.2 versions: SUPLA for enclosures without canopy and SUPLAT for enclosures with canopy.

Horizontal coupling frame for PLA and PLA...T enclosures

Height (A)

Enclosure dimensions

Depth (C)

Reference

500 320 MUPLA 53

750 320 MUPLA 73

1000 320 MUPLA 103

1250 320 MUPLA 123

1500 320 MUPLA 153

500 420 MUPLA 54

750 420 MUPLA 74

1000 420 MUPLA 104

1250 420 MUPLA 124

1500 420 MUPLA 154

Supplements for coupling PLA and PLA...T enclosures

Depth (C)

Enclosure dimensionsPLA

320 SUPLA 3 SUPLA 3T

420 SUPLA 4 SUPLA 4T

PLA...T

MUPLA...SUPLA...

MUPLA...SUPLA...

03_084_100_EN.indd 8403_084_100_EN.indd 84 2/4/08 12:55:052/4/08 12:55:05

A +

38

C = 320/420

3/85


Coupling enclosures using an adhesive gasket that guarantees watertightness at the vertical joint of the enclosures PLA.

Ref.: UVPLA.

Application Reference

Adhesive gasket UVPLA

Vertical coupling of enclosures

Made of reinforced pressed polyester, for exterior installation of closed enclosures.

c Colour RAL-7032.

c Self-extinguishable; high resistance to impacts and temperature.

c Excellent resistance to outdoor conditions.

c The nominal height of the enclosure is increased 38 mm.

Canopies

Width (B) Depth (C) No. of doors


500 320 1 TJPLA 53

750 320 1 TJPLA 73

1000 320 2 TJPLA 103

1250 320 2 TJPLA 123

500 420 1 TJPLA 54

750 420 1 TJPLA 74

1000 420 2 TJPLA 104

1250 420 2 TJPLA 124

03_084_100_EN.indd 8503_084_100_EN.indd 85 2/4/08 12:55:062/4/08 12:55:06

3/86


B+35

200

B

C

305

C-10

395

To be coupled to enclosures with open bases, Ref.: PLAZ…

Made of fiberglass reinforced polyester.

c Colour RAL-7032.


c Double insulation; excellent resistance to weather conditions.

c 200 mm front cover accessible from the interior.

c 305 mm height fixed front panel, allowing the enclosure to be completely or partially flush built in.

c Fixing profile for cable entry.

c Sides with knock-out entry PG-36.

Plinths



500 320 1 ZHPLA 53

750 320 1 ZHPLA 73

1000 320 2 ZHPLA 103

1250 320 2 ZHPLA 123

500 420 1 ZHPLA 54

750 420 1 ZHPLA 74

1000 420 2 ZHPLA 104

1250 420 2 ZHPLA 124

aaaaaaaaB+20

B

C

300/420

60

65To be coupled to enclosures with closed bases, Ref.: PLA…


c Colour RAL-7032.


c Excellent resistance to outdoor conditions.

Bases



500 320 1 ZNPLA 53

750 320 1 ZNPLA 73

1000 320 2 ZNPLA 103

1250 320 2 ZNPLA 123

500 420 1 ZNPLA 54

750 420 1 ZNPLA 74

1000 420 2 ZNPLA 104

1250 420 2 ZNPLA 124

03_084_100_EN.indd 8603_084_100_EN.indd 86 2/4/08 12:55:062/4/08 12:55:06

26

(1)

B+52A-3

7518

7,5

3/87


To be coupled to the models of enclosures with open plinth-type bases, Ref.: PLAZ…


c Colour RAL-7032.

c Self-extinguishing; excellent resistance to outdoor conditions.

c Easily machined.

1-door enclosures 2-door enclosures

Cable entry plate



500 320 1 ECPLAZ 53

750 320 1 ECPLAZ 73

1000 320 2 ECPLAZ 103

1250 320 2 ECPLAZ 123

500 420 1 ECPLAZ 54

750 420 1 ECPLAZ 74

1000 420 2 ECPLAZ 104

1250 420 2 ECPLAZ 124

100

C-7

8

C-2

04

25

63

1011

430

21 10 31

B-40

B-40

C-7

8

C-2

04

25

11

63

10

Set of 6 metal pieces in passivated zinc-coated steel.

c Fixing to the sides with 4 or 6 pieces in horizontal (1).

c In all cases, the maximum admissible load is that which corresponds to 150 kg/m2 of plate surface. See the enclosure lifting table, page 3/111.

Ref.: FMPLA.

Wall mounting kit

03_084_100_EN.indd 8703_084_100_EN.indd 87 2/4/08 12:55:082/4/08 12:55:08

C-160

B-60

3/88


Frame for fixing those enclosures with open plinth-type bases directly to the floor, Ref.: PLAZ…

Fixing enclosures with open bases to the floor, Ref.: PLA… is done directly, with the solution being a stud with a standard screw via the ZNPLA bottom.



Ref.: FS/PLA2.

Floor-fixing frame

500 320 1 MFPLAZ 53

750 320 1 MFPLAZ 73

1000 320 2 MFPLAZ 103

1250 320 2 MFPLAZ 123

500 420 1 MFPLAZ 54

750 420 1 MFPLAZ 74

1000 420 2 MFPLAZ 104

1250 420 2 MFPLAZ 124

Set of 4 studs for floor fixing

Door retainers to be directly incorporated into the indicated enclosures.

c Opening of the retainer: 90º or 120º for all models. Ref. RET/PLAU.

c Opening of the retainer: 110º for models PLA, PLA...T and PLAZ.Ref. RET/PLA.

RET/PLAU

RET/PLA

Door retainer

03_084_100_EN.indd 8803_084_100_EN.indd 88 2/4/08 12:55:092/4/08 12:55:09

25

C

30*

C-40

E

D

3/89


Internal door manufactured in painted aluminium, grey RAL-7032.

Double bar locks, allowing change for triangle, square, etc. inserts of CRN enclosures (see general catalogue).

In enclosures with a closed bottom, Ref.: PLA, the internal PIPLA doors are coupled directly.

In models with open plinth-type base, Ref.: PLAZ..., the PTZ adapter plates must be ordered separately (see footnote).

Depth of the positioning of the internal door is adjustable 25 mm.* In enclosures with a transparent KT door, subtract 5 mm.

Internal doors

No. of doors Individual internal doors in 2-door enclosure reference*Width (B)Height (A)

Total lower door reference*D E

Weight (kg)

For attachment to enclosures Dimensions

* To be coupled to enclosures with open bottom, Ref.: PLAZ, adaptor plates must be ordered separately, Ref.: PTZ 320 or PTZ 420, for 320 or 420 mm depth one-door enclosures.

PTZ 320/2P or PTZ 420/2P must be ordered for two-door enclosures.

500 500 1 PIPLA 55 - 398 398 1.6

500 750 1 PIPLA 57 - 398 648 2.2

500 1000 2 - PIPLA 55 + PIPLA 55 - - -

500 1250 2 - PIPLA 55 + PIPLA 57 - - -

750 500 1 PIPLA 75 - 648 398 2.2

750 750 1 PIPLA 77 - 648 648 3.1

750 1000 2 - PIPLA 75 + PIPLA 75 - - -

750 1250 2 - PIPLA 75 + PIPLA 77 - - -

1000 500 1 PIPLA 105 - 898 398 2.8

1000 750 1 PIPLA 107 - 898 648 4.1

1000 1000 2 - PIPLA 105 + PIPLA 105 - - -

1000 1250 2 - PIPLA 105 + PIPLA 107 - - -

1250 500 1 PIPLA 125 - 1148 398 3.4

1250 750 1 PIPLA 127 - 1148 648 5

1250 1000 2 - PIPLA 125 + PIPLA 125 - - -

1250 1250 2 - PIPLA 125 + PIPLA 127 - - -

1500 500 1 PIPLA 155 - 1398 398 4

1500 750 1 PIPLA 157 - 1398 648 6

1500 1000 2 - PIPLA 155 + PIPLA 155 - - -

1500 1250 2 - PIPLA 155 + PIPLA 157 - - -

03_084_100_EN.indd 8903_084_100_EN.indd 89 2/4/08 12:55:102/4/08 12:55:10

3/90


Direct-action 5 mm double bar lock, operated with key LDB5. Included in standard supply.Accepts all the types of operation referenced in the following table by changing the inserts of the standard lock.

Embellishing kit for direct-action key-operated lock (without handle): Ref.: EB/PLA.

Standard lock for completely closed enclosures

CHANGING INSERTS OF THE STANDARD LOCK

Specifications ReferenceType of lock Type of operation

6.5 mm triangle

lock, operated TT6/CRN

with key LT6,5.

7 mm triangle

ock, operated TT7/CRN

with key LT8.

8 mm triangle

lock, operated TT8/CRN

with key LT8.

6 mm square

lock, operated TC6/CRN

with key LC7.

7 mm square


with key LC7.

8 mm square


with key LC8.

Double bar

lock, operated

with key LDB5. TDB/PLA

Included in

standard supply.

Padlock BC/PLA

* To obtain the complete lock, in addition to the EBM/PLA trim, the T…/OLN or T…/PLA types of locks, indi-cated on the following page, must be ordered separately.

CHANGING TO HANDLE LOCK

Specifications ReferenceType of operation

Embellishing kit

with handle lock.* EBM/PLA*

03_084_100_EN.indd 9003_084_100_EN.indd 90 2/4/08 12:55:112/4/08 12:55:11

3/91


Double bar handle lock, operated by key LDB5. Included in standard supply.Accepts all the types of operation referenced in the following table by changing the inserts.

Embellishing kit with handle Ref.: EBM/PLA.

* To obtain the complete lock, in addition to the CBCM/PLA trim, the T…/OLN type of lock, indicated on this page, must be ordered separately.** To obtain the complete lock, in addition to the EB/PLA trim, the T…/CRN or TDB/PLA types of locks, indi-cated on the previous page, must be ordered separately.

Standard lock for enclosures with open top or open base

CHANGING INSERTS OF THE STANDARD LOCK

7 mm triangle

lock, operated TT7/OLN

with key LT8.

8 mm triangle

lock, operated TT8/OLN

with key LT8.

6 mm square

lock, operated TC6/OLN

with key LC7.

7 mm square


with key LC7.

8 mm square


with key LC8.

Lock with key type 405. TL/OLN

Lock with key type JIS. TJIS/OLN

Lock with reinforced-type key TLR/OLN

Lock with key type FAC. TFAC/OLN

DIN insert

adapter. ABDIN/OLN

Pushbutton operated. TS/PLA

5 mm double

bar lock included TDBM/PLA

in standard supply.

Handle lock with CBCM/PLA*

padlocking device.*

Protective cover (optional). TPBM/PLA

CHANGING TO LOCK WITHOUT HANDLE



Embellishing kit without

handle lock.** EB/PLA**

03_084_100_EN.indd 9103_084_100_EN.indd 91 2/4/08 12:55:122/4/08 12:55:12

A - 158

A - 200

1

1

C -

116

C -

170

27

21 21

3/92


Support set made of the fixing supports and all the necessary hardware, for fixing the PPTR transparent protective screens to the corresponding PLA enclosures.

Made of 4 mm transparent polycarbonate. Supplied without the SPTR 77 support set, which must be purchased separately.

Transparent protective screens

Height Width

ReferenceEnclosure dimensions

500 500 PPTR 55

500 750 PPTR 57

750 500 PPTR 75

750 750 PPTR 77

Fixing supports for protective screens

Reference Application

SPTR 77 PPTR 55/57/75/77

03_084_100_EN.indd 9203_084_100_EN.indd 92 2/4/08 12:55:132/4/08 12:55:13

G

E

D F

350

437.5

H-87.5

H

E

e10.5

150

100

75

12.5

10.5 25 25

2525

25

25

25

25

Ø6.5

Ø8.5

Ø6.5

Ø8.5

150

100

75

10.5

2525

10.5

25 25

Ø 6.5

Ø 8.5

Ø 6.5Ø 8.5

3/93

PLA Mounting accessories

Made of galvanised steel sheet, with reinforcement fold on models starting with a height of 1000 mm.

Directly joined to the bottom of the enclosure itself or to the depth adjustable supports.

On two-door enclosures, a full plate or 2 partial plates may be fitted. See table.

Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMM plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.

c Maximum load 150 kg/m2.

models from PMM 1010

FIG. 1 FIG. 2

Metal mounting plates

500 500 1 PMM 55 1 - - 390 375 350 350 - 2 2.5

500 750 1 PMM 75 1 - - 640 375 600 350 - 2 3.8

500 1000 2 PMM 510 2 PMM 55 + PMM 55 1 390 875 350 -0 437.5 2.5 6.3

500 1250 2 - - PMM 55 + PMM 75 1 -0 -0 -0 -0 - - -

750 500 1 PMM 75 1 - - 640 375 600 350 - 2 3.8

750 750 1 PMM 77 1 - - 640 625 600 600 - 2.5 7.8

750 1000 2 PMM 710 2 PMM 75 + PMM 75 1 640 875 600 -0 437.5 2.5 10.6

750 1250 2 PMM 712 2 PMM 75 + PMM 77 1 640 1125 600 -0 687.5 2.5 17.6

1000 500 1 PMM 105 1 - - 890 375 850 350 - 2.5 6.5

1000 750 1 PMM 107 1 - - 890 625 850 600 - 2.5 10.8

1000 1000 2 PMM 1010 2 PMM 105 + PMM 105 1 875 875 850 -0 437.5 2.5 15

1000 1250 2 PMM 1012 2 PMM 105 + PMM 107 1 875 1125 850 -0 687.5 2.5 19.3

1250 500 1 PMM 125 1 - - 1125 375 1100 350 - 2.5 8.6

1250 750 1 PMM 127 1 - - 1125 625 1100 600 - 2.5 14.2

1250 1000 2 PMM 1210 2 PMM 125 + PMM 125 1 1125 875 1100 -0 437.5 2.5 19.4

1250 1250 2 PMM 1212 2 PMM 125 + PMM 127 1 1125 1125 1100 -0 687.5 2.5 24.9

1500 500 1 PMM 155 1 - - 1375 375 1350 350 - 2.5 10.6

1500 750 1 PMM 157 1 - - 1375 625 1350 600 - 2.5 17.3

1500 1000 2 PMM 1510 2 PMM 155 + PMM 155 1 1375 875 1350 -0 437.5 2.5 23.8

1500 1250 2 PMM 1512 2 PMM 155 + PMM 157 1 1375 1125 1350 -0 687.5 2.5 30.5

(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PMM of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure

Height (A) Width (B)

No. of doors

Fig. No.Reference Fig. No. D E F G H e (kg)

To couple to enclosures with dimensions (1) Full plate Individual plates, two-door

enclosuresDimensions full plate

Reference

03_084_100_EN.indd 9303_084_100_EN.indd 93 2/4/08 12:55:152/4/08 12:55:15

G

E

D F

350

437.5

H-87.5

H

E

e10.510.5

150

100

75

150

100

75

10.5

10.5

3/94


Made of bakelite in black RAL-9005 (Ref.: PMB..) or in polyester in grey RAL-7032 (Ref.: PMA..).


On two-door enclosures, a full plate or 2 partial plates may be fitted. See table.

Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMB plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.


FIG. 1 FIG. 2

Insulating mounting plates

(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PM.. of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure.

(2) PMA: polyester, PMB: bakelite.

500 500 1 PM.. 55 1 - - 390 375 350 350 - 4 0.9

500 750 1 PM.. 75 1 - - 640 375 600 350 - 4 1.3

500 1000 2 PM.. 510 2 PM.. 55 + PM.. 55 1 390 875 350 -0 437.5 5 2.4

500 1250 2 - - PM.. 55 + PM.. 75 1 -0 -0 -0 -0 - - -

750 500 1 PM.. 75 1 - - 640 375 600 350 - 4 1.3

750 750 1 PM.. 77 1 - - 640 625 600 600 - 5 2.8

750 1000 2 PM.. 710 2 PM.. 75 + PM.. 75 1 640 875 600 -0 437.5 5 3.9

750 1250 2 PM.. 712 2 PM.. 75 + PM.. 77 1 640 1125 600 -0 687.5 5 5

1000 500 1 PM.. 105 1 - - 890 375 850 350 - 5 2.3

1000 750 1 PM.. 107 1 - - 890 625 850 600 - 5 3.9

1000 1000 2 PM.. 1010 2 PM.. 105 + PM.. 105 1 890 875 850 -0 437.5 5 5.5

1000 1250 2 PM.. 1012 2 PM.. 105 + PM.. 107 1 890 1125 850 -0 687.5 5 7.1

1250 500 1 PM.. 125 1 - - 1140 375 1100 350 - 5 3

1250 750 1 PM.. 127 1 - - 1140 625 1100 600 - 5 5

1250 1000 2 PM.. 1210 2 PM.. 125 + PM.. 125 1 1140 875 1100 -0 437.5 5 7

1250 1250 2 PM.. 1212 2 PM.. 125 + PM.. 127 1 1140 1125 1100 -0 687.5 5 9

1500 500 1 PMB 155 1 - - 1390 375 1350 350 - 5 3.7

1500 750 1 PMB 157 1 - - 1390 625 1350 600 - 5 6.1

1500 1000 2 PMB 1510 2 PMB 155 + PMB 155 1 1390 875 1350 -0 437.5 5 8.6

1500 1250 2 PMB 1512 2 PMB 155 + PMB 157 1 1390 1125 1350 -0 687.5 5 11


No. of doors

Fig. No.Reference (2) Fig. No. D E F G H e (kg)

To couple to enclosures with dimensions (1) Full plate Individual plates, two-door

enclosuresDimensions full plate

Reference (2)

Bakelite Polyester

03_084_100_EN.indd 9403_084_100_EN.indd 94 2/4/08 12:55:192/4/08 12:55:19

3/95


Plates specially designed for quick mounting of equipment using the TFP locking nuts. Made of zinc-coated steel.


Possibility of incorporating 2 individual plates on two-door enclosures. See table.

Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMR plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.


Universal perforated mounting plates

(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PMM of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure.


No. of doors

Reference Reference D E F GThickness

(mm))Weight (kg)

To join the enclosures (1) Full plate Individual plates, two-door enclosures

Dimensions full plate

500 500 1 PMR 55 - 370 376 350 350 2 1.1

500 750 1 PMR 57 - 370 626 350 600 2 1.7

500 1000 2 - PMR 55 + PMR 55 370 376/376 350 350/350 2 -

500 1250 2 - PMR 55 + PMR 57 370 376/626 350 350/600 2 -

750 500 1 PMR 75 - 620 376 600 350 2 1.7

750 750 1 PMR 77 - 620 626 600 600 2 2.7

750 1000 2 - PMR 75 + PMR 75 620 376/376 350 350/350 2 -

750 1250 2 - PMR 75 + PMR 77 620 376/626 350 350/600 2 -

1000 500 1 PMR 105 - 870 376 850 350 2 2.1

1000 750 1 PMR 107 - 870 626 850 600 2 4.1

1000 1000 2 - PMR 105 + PMR 105 870 376/376 850 350/350 2 -

1000 1250 2 - PMR 105 + PMR 107 870 376/626 850 350/600 2 -

1250 500 1 PMR 125 - 1120 376 1100 350 2 3.3

1250 750 1 PMR 127 - 1120 626 1100 600 2 4.8

1250 1000 2 - PMR 125 + PMR 125 1120 376/376 1100 350/350 2 -

1250 1250 2 - PMR 125 + PMR 127 1120 376/626 1100 350/600 2 -

1500 500 1 PMR 155 - 1370 376 1350 350 2 4.2

1500 750 1 PMR 157 - 1370 626 1350 600 2 6.3

1500 1000 2 - PMR 155 + PMR 155 1370 376/626 1350 350/350 2 -

1500 1250 2 - PMR 155 + PMR 157 1370 376/626 1350 350/600 2 -

F

D

GE

15

03_084_100_EN.indd 9503_084_100_EN.indd 95 2/4/08 12:55:212/4/08 12:55:21

3/96


c Allow for depth adjustment of PMM, PMB and PMR mounting plates, on any model of enclosure.

c Set of 4 adjustable supports on the profile of the aluminium guide, able to be fixed at any point along its entire length and with reference positioning every 25 mm.

c Models with a closed base. Ref.: PLA...The DPLA adjustable supports can be coupled directly without the need for other accessories.

Detail of DPLA plate supports in enclosure with closed base.

62*

C

35

C-70

62*

C

35

C-70

* For enclosures with a transparent KT door, subtract 5 mm.

enclosure with open plinth-type base, reference PLAZ… , with two doors, with adjustable plate fixed with DPLA supports and PTZ adaptor plates.

Set of 4 adjustable fixing supports for fixing an additional plate.

Ref.: EDPLA.

Detail of the DPLA plate supports with an additional set of fixing supports, Ref.: EDPLA, allowing the placement of two plates (back to back), for example in enclosures with a rear door.

PTZ 420

PTZ 420/2P

Set of adjustable mounting plate supports

c Two-door modelsTwo sets of DPLA adjustable supports must be ordered, and for the models open bottom, add one PTZ.../2P set.

* In two-door enclosures, in order to mount a full plate or two individual plates, 2 DPLA plate fixing sets must

be ordered, as indicated in the table.

To be installed in enclosures To be installed in enclosures reference

Depth (C) No. of doors PLA... PLAZ...

320 1 DPLA 320 DPLA 320 + PTZ 320

420 1 DPLA 420 DPLA 420 + PTZ 420

320 2 (2) DPLA 320* (2) DPLA 320* + PTZ 320/2P

420 2 (2) DPLA 420* (2) DPLA 420* + PTZ 420/2P

c Models with open plinth-type base. Ref.: PLAZ... In addition to the DPLA adjustable supports, a set of PTZ adaptor plates must be ordered.

DPLA 420

Set of fixing supports for additional plate

03_084_100_EN.indd 9603_084_100_EN.indd 96 2/4/08 12:55:222/4/08 12:55:22

Detail of the MOL profile fixed to the back of the enclosure.

3/97

CDP double profile DIN rail for direct fixing of equipment. Detail of the TDC sliding nut.

Detail of the MOL profile and TDM nut.The notches in the profile permit adjustment every 2.5 mm.

Set of two vertical profiles for direct fixing to the back of the enclosure.The notches in the profile every 2.5 mm and the marks every 25 mm facilitate the positioning of plates, rails, etc.

To make depth adjustment of the chassis possible, the MOL profiles must be fixed on a set of DPLA or DPLA + PTZ adjustable mounting plate supports, as in the following table.

Detail of the MOL profile fixed to the set of DPLA adjustable plate support.


Universal chassis system

Set of profiles for universal chassis

Depth (C) No. of doors PLA... PLAZ...

To be installed in enclosures To be installed in enclosures reference

320 1 DPLA 320 DPLA 320 + PTZ 320

420 1 DPLA 420 DPLA 420 + PTZ 420

320 2 (2) DPLA 320 (2) DPLA 320 + PTZ 320/2P

420 2 (2) DPLA 420 (2) DPLA 420 + PTZ 420/2P

To couple to enclosures with height (A) Reference

750 MOL 75

1000 MOL 100

1250 MOL 125

1500 MOL 150

Universal chassis made up of a set of 2 MOL profiles prepared for partial mounting plates and DIN rails, for fixing any type of equipment.

The chassis can be fixed directly to the back of the enclosure or on the set of adjustable mounting plate supports, in this case making depth adjustment possible.

In two-door enclosures with 1000 and 1250 mm width, two 500 mm chassis, or 1 of 500 + 1 of 750 mm width, respectively, can be mounted.

03_084_100_EN.indd 9703_084_100_EN.indd 97 2/4/08 12:55:242/4/08 12:55:24

B - 100

A - 100

45°

40

20

44,5

7

77

44,5

40

7

10

B-95

H

3/98

Insulating polyester mounting plates, to be installed on the side of PLA enclosures.

The TEX8 inserts must be ordered separately.

Lateral mounting plates

Height Depth

ReferenceEnclosure dimensions

500 320 PMLA 53

500 420 PMLA 54

750 320 PMLA 73

750 420 PMLA 74

1000 320 PMLA 103

1000 420 PMLA 104

1250 320 PMLA 123

1250 420 PMLA 124

Made of galvanised steel. They are placed on the MOL profiles using TDM 8 nuts and TOR 16/8A screws, which must be ordered separately.

To couple to enclosures with width (B)

Plate height (H)

Reference

500 247 PMP 2550

750 247 PMP 2575

1000* 247 PMP 25100

500 397 PMP 4050

750 397 PMP 4075

1000* 397 PMP 40100

* The 1000 mm width enclosures allow for mounting 2 chassis with PMP...50 plates.


Partial mounting plates for universal chassis

03_084_100_EN.indd 9803_084_100_EN.indd 98 2/4/08 12:55:312/4/08 12:55:31

3/99


Rails of galvanised steel. They are placed on the MOL profiles using TDM 6 nuts and TOR 12/6A screws, which must be ordered separately.

* The 1000 mm width enclosures allow for mounting 2 chassis with C...50 rails.

Metal rails and nuts

To couple to enclosures with width (B)

Double profile reference

Symmetric DIN reference35 7.5

Symmetric DIN reference35 15

Asymmetric DIN reference

500 - CSPLA 50 CAPLA 50 -

750 - CSPLA 75 CAPLA 75 -

1000 - CSPLA 100 CAPLA 100 -

In 2 metre strips CO 35 - CA 32 CDP 200

In 2 metre strips COT 35 - CAT 32 -

In 2 metre strips - CO 35/15 - -

In 2 metre strips - COT 35/15 - -

(1) For symmetrical rails, Ref.: CO, COT and CSPLA, and double profile CDP...

(2) For double profile rails CDP...

Thread typeUnits per package Units per package Length (mm) Units per package

Nuts for fixing equipment Nuts for MOL profiles Fixing screw with washer

Units per package

M4 TDE 4 100 - 100 - - TOR 10/4A 10 100

M4 - - - - - - TOR 16/4A 16 100

M5 TDE 5 100 - - - - TOR 12/5A 12 100

M5 - - TDC 56 100 - - TOR 18/5A 18 100

M6 TDE 6 100 TDC 56 100 TDM 6 10 TOR 12/6A 12 100

M6 - - - - - - TOR 18/6A 18 100

M8 - - - - TDM 8 10 TOR 16/8A 16 50

M8 - - - - - - TOR 20/8A 20 10

Sheet ∅ 4.8 mm TOR 16/5AT 16 100

MOUNTING ACCESSORIES

(2)(1)

03_084_100_EN.indd 9903_084_100_EN.indd 99 2/4/08 12:55:332/4/08 12:55:33

12

18

C-1

00

25

B-4227

12

250

200

200

200

200

11x13

3/100


BANPLA tray to be placed horizontally to support various materials, or simply as a separator. Designed to be installed in one-door enclosures.

It is mounted directly on the bottom of the enclosure using the lateral bosses.

If you want to place the tray, or various trays, at differing heights, 2 sets of 2 SPLA vertical profiles (total of 4), must be ordered, as indicated in the table.

Maximum load:Depth 320: 60 kgDepth 420: 50 kg

* Are only necessary if you want to place the tray at differing heights.

(1) For the 1250 mm enclosures, these trays may be placed using the SBPLA profiles, on the 500 and

750 mm side.

Support tray

Height (A) Width (B) Depth (C)

ReferenceTo couple to enclosures (1)

500 500 320 BANPLA 53 -

500 750 320 BANPLA 73 -

750 500 320 BANPLA 53 2 SPLA 75

750 750 320 BANPLA 73 2 SPLA 75

1000 500 320 BANPLA 53 2 SPLA 100

1000 750 320 BANPLA 73 2 SPLA 100

1250 500 320 BANPLA 53 2 SPLA 125

1250 750 320 BANPLA 73 2 SPLA 125

1500 500 320 BANPLA 53 2 SPLA 150

1500 750 320 BANPLA 73 2 SPLA 150

500 500 420 BANPLA 54 -

500 750 420 BANPLA 74 -

750 500 420 BANPLA 54 2 SPLA 75

750 750 420 BANPLA 74 2 SPLA 75

1000 500 420 BANPLA 54 2 SPLA 100

1000 750 420 BANPLA 74 2 SPLA 100

1250 500 420 BANPLA 54 2 SPLA 125

1250 750 420 BANPLA 74 2 SPLA 125

1500 500 420 BANPLA 54 2 SPLA 150

1500 750 420 BANPLA 74 2 SPLA 150

Tray Supports*

For 19” RACK accessories, consult the VDI catalogue.

Ref.: SB/PLA.

19” rack support and trays for two-door enclosures

03_084_100_EN.indd 10003_084_100_EN.indd 100 2/4/08 12:55:382/4/08 12:55:38

3/101

PLA Current distribution accessories

Clip in fasteners to be installed directly on 19” racks and on slotted MR mounting plates.

Reference: GCR.

GCR ties


Adjustable ties

White BlackL ∅

minimum∅

maximum

M

Reference Use

LZ25100 LN25100 100 2.5 1.6 22

LZ25200 LN25200 200 2.5 1.6 49

LZ35150 LN35150 150 3.5 1.6 35

LZ35200 LN35200 200 3.5 1.6 49

LZ35300 LN35300 300 3.5 1.6 75

LZ46150 LN46150 150 4.6 1.6 36

LZ46200 LN46200 200 4.6 1.6 49

LZ48270 LN48270 270 4.8 1.6 73

LZ46390 LN46390 390 4.6 1.6 109

LZ76390 LN76390 390 7.6 4.7 108

To tighten and cut to size the adjustable ties. They facilitate wiring and save time, preventing the packets of cables from loosening.



Tightening tools

Reference

MARK3 2.5 ÷ 4.8


Reference

MARK20 2.5 ÷ 4.8

MARK21 4.6 ÷ 7.6


03_101_107_EN.indd 10103_101_107_EN.indd 101 2/4/08 12:57:002/4/08 12:57:00

3/102


To use with soft materials: 7 mm Ø hole, or hard materials: 8 mm Ø hole. Ties are attached up to 9 mm width. Material: 6.6 nylon

Ref.: LOK01.

Stud


Tie fixing support


tiesC

KR6 12 18 9 M4 2.5 ÷ 4.8

KR8 14.5 25 12 M6 2.5 ÷ 7.6


Locking clips

Reference

SFC1 6 3.2 1

SFC2 6 1 2

FigureMaximum width

panel mm∅ perforation

mm

SFC2 SFC1

Fig. 1 Fig. 2

03_101_107_EN.indd 10203_101_107_EN.indd 102 2/4/08 12:57:012/4/08 12:57:01

3/103



Support heads

Reference A B Fixing screwAdmissible width ties

C

FH18 7.1 13.3 4 M4 2.5

FH30 9.5 17.9 4.7 M5 3.5

FH50 11.3 22.2 6.2 M6 4.7




tiesD

MB3A 19.1 19.1 4.8 3.2 13.2 2.5 ÷ 3.5

MB4A 28.5 28.5 5.5 4 20.2 2.5 ÷ 4.8


Tie fixing support

Reference

LKC 2.5 7.6 M5


ties mm

adhesive support

03_101_107_EN.indd 10303_101_107_EN.indd 103 2/4/08 12:57:032/4/08 12:57:03

3/104


2 versions, fixed and graduated, ∅ from 5 to 25.4 mm. Material: black 6.6 nylon.


Reference∅ A

min. - max.B D EC

NX1 5 3.5 1 6.2 13.7

NX3 8 3.9 1 9.4 20.5

NX5 12 3.9 1 9.4 24

NX8* 14.3 ÷ 15.8 4 1.3 12.6 32

NX11 17.4 ÷ 20 4 1.3 12.6 37

NX14 22.2 ÷ 25.4 4.3 1.5 16 45


NX 1-3-5 NX 8-11-14



Reference

LKM/HE 2.5 7.6 M5


ties mm

03_101_107_EN.indd 10403_101_107_EN.indd 104 2/4/08 12:57:042/4/08 12:57:04

3/105


Insulating membrane glands made of PVC with entry that can be adjusted for cables.



Capacity

ECPC-3 1 25 21.5 18 5 3.2 13 5 to 18 Pg 9 to 11

ECPC-5 1 33 29.5 26 5 3.2 20 5 to 26 Pg 9 to 16

ECPC-6 1 43 38.5 36 5 3.2 22 5 to 36 Pg 9 to 21

ECPC-9 2 70 63 60 28 3 20 28 to 60 Pg 21 to 48

ECPC-15 2 98 90 87 28 3 23 28 to 87 Pg 21 to 48


Fig. 1 Fig. 2

Ø A

Ø B


Protective sleeves


PC-1 15.2 12.7 Pg 9

PC-2 18.6 16 Pg 11

PC-3 20.4 17.8 Pg 13.5

PC-4 22.5 19.8 Pg 16

PC-5 28.3 25.3 Pg 21

PC-6 37 33.6 Pg 29

PC-7 47 43 Pg 36

03_101_107_EN.indd 10503_101_107_EN.indd 105 2/4/08 12:57:042/4/08 12:57:04

3/106


Øexterior

SteelFlexible


Protective sleeves

Adjustable membrane

glandsPlain plugs


Flexible steel with

PVC


4 EC-1 to EC-7

Pg 9 15.2 12.7 12.4 12 11.1 6 2.5 - - 16 14 ECPC-3 to ECPC-6 PC-1 - -

ECN-5 to ECN-10

10 4 2.5 EC-2 to EC-7 EC-1



EC-3 to EC-7 EC-3


ECN-5 to ECN-10

EC-4 to EC-7


ECN-5 to ECN-10

EC-5 to EC-7 EC-5



95 35 25 16 EC-6; EC-7 EC-6 TC-5


150 ECN-7; ECN-10 ECN-6

185 35 EC-7 EC-7


300 ECN-10

95 70 ECPC-9; ECPC-15

Pg 42 54 50 48 48 47 - 120 95 70 55 52.5 ECN-10 - - -

120 95 ECPC-9; ECPC-15

Pg 48 60 56 54.2 52.5 51.4 - 150 150 120 61 58 ECN-10 - - -



1 2 3 4


No. of conductors



Ø perforations to




Reference

BBH-29 6-50 -

BBH-29C* 6-50 -

BBH-30 10-95 -

BBH-31 16-150 -

BBH-32 50-240 -

BBH-29D 6-50 6-50

BBH-29DC* 6-50 6-50

BBH-30D 10-95 10-95

BBH-31D 25-150 16-150

BBH-32D 95-240 5-240

Main section (mm2)

Bypass section (mm2) Reference

BBH-29P 6-50 -

BBH-29PC* 6-50 -

BBH-29DP 6-50 6-50

BBH-29DPC* 6-50 6-50


Main section (mm2)

Bypass section (mm2)

BBH-29 BBH-29D

BBH-29P BBH-29DP

Desig-nation

03_101_107_EN.indd 10603_101_107_EN.indd 106 2/4/08 12:57:052/4/08 12:57:05

3/107

ReferenceCable bypass section

(mm2)Plate thickness (mm) Figure

BPCH 516 1.5 to 16 5 2

BPCH 550 1.5 to 50 5 2

BPCH 5120 16 to 120 5 2

BPCH 1016 1.5 to 16 10 1

BPCH 1050 1.5 to 50 10 1

BPCH 10120 16 to 120 10 1









Reference

S.04 1 × 4 30 20 13 21 4

S.06 1 × 6 33 25 16 24 7

S.10 1 × 10 38 28 16 28 6

S.16 1 × 16 42 32 19 32 9

S.25/35 1 × 35 46 38 23 34 11

S.50 1 × 50 52 45 27 40 15

S.70 1 × 70 55 50 30 40 15

S.95/100 1 × 100 58 54 33 40 20


Sectionm/m2 A B C D E



1 2

03_101_107_EN.indd 10703_101_107_EN.indd 107 2/4/08 12:57:072/4/08 12:57:07

35590

7066

3/108

PLA Lighting accessories

Compact lamp



or on 35 mm symmetric LAM-75 220 V/16 A 220 V/50 Hz

DIN rail


symmetric DIN rail LAC-75 220 V/16 A 220 V/50 Hz


or on 35 mm symmetric LAM-75/120 120 V/15 A 120 V/60 Hz

DIN rail


symmetric DIN rail LAC-75/120 120 V/15 A 120 V/60 Hz



c Consumption 11 W.







c Power: 11 W.

c Luminosity: 900 lm

c Lifespan: 10000 h.


c IP20.

c Class I.

Slimline lamp





03_108_109_EN.indd 10803_108_109_EN.indd 108 5/3/08 11:29:425/3/08 11:29:42

3/109

PLA Lighting accessories

396

67

100

Dual lamp

1

2

3

4


Motion-activated



On/off switch with the possibility Magnetic, via connection LAMIN 220 V/50 Hz

of door switch, screws and/or 35 DIN rail (1) 2 LAMIN 120 120 V/60 H


LAMPO 220 V/50 Hz


Support for LAMDP, Adhesive or screws

LAMIN, LAMPO lamp 4 SOLAM

(1) DIN rail not provided..










c Consumption 60 W.



Incandescent lamp

Reference

LAI/OL 68

500

03_108_109_EN.indd 10903_108_109_EN.indd 109 5/3/08 11:29:485/3/08 11:29:48

3/110

PLA Natural ventilation accessories

To connect the inside of the enclosure with the exterior atmosphere and prevent condensation. Can be fixed onto the outside.

VM-25 VM-27

Ventilation devices


VM-27


03_110_117_EN.indd 11003_110_117_EN.indd 110 2/4/08 12:58:142/4/08 12:58:14

174

188 22 278 40

234

3/111

Plan size

A4 PP-A4

A5 PP-A5

Reference

Insulated

PLA Complementary accessories

PP-A models made of thermoplastic in grey RAL-7035.


For holding DIN A3-A4 or A5-sized plans.

Document pocket


Dodge-type brass nuts designed to be incorporated into the bosses of PLM enclosures.

Expandable nuts



M8 For the back of the enclosure TEX 8

ReferenceSpecifications For attachment to enclosures

There is a set of slings to cover the most common enclosure or suite lifting needs.

Ref: ELS 1520.

c Table of dimensions indicating the maximum weight in kg anticipated for each enclosure or suite. The fields highlighted indicate the dimensional range of use planned for the lifting equipment ELS 1520.

(A) and (B) correspond, respectively, to the nominal height and width in mm of the enclosures or suites.

Lifting the enclosures

500 750 1000 1250 1500 1750 2000

1500 113 169 225 281 338 394 450

1200 94 141 188 234 281 328 375

1000 75 113 150 188 225 263 300

750 56 84 113 141 169 197 225

500 38 56 75 94 113 131 150

Width (B)Height (A)

TEX 8 TEX 6 TEX 5

03_110_117_EN.indd 11103_110_117_EN.indd 111 2/4/08 12:58:142/4/08 12:58:14

3/112

DLP distribution chassis set for modular equipment, to be coupled to all models of PLA enclosures.

c Distance of 40 to 85 mm, adjustable as needed by the customer, between the symmetric profile for equipment fixing and the interior protective cover.

c Rigid structure made of galvanised steel.

c Cover and frame insulating in self-extinguishing material in RAL-7032. Quick mounting, without the need for screws.

c System for identifying circuits included in the standard supply.

c Earth and neutral bypass terminal block, Ref.: RBLZ/21656 (included in standard supply).

c Possibility of installing plain mounting plates and covers to mount various material.

In enclosures with a closed base, Ref.: PLA… the 1500 height DLP chassis are coupled directly.

In models with open plinth-type bottom, Ref.: PLAZ should be ordered separately from the PTZ adapter plates (see footnote).

PLA Applications

* To be coupled to enclosures with open bottom, Ref.: PLAZ adaptor plates must be ordered separately, Ref.: PTZ 320 or PTZ 420, for 320 or 420 mm depth one-door enclosures.

PTZ 320/2P or PTZ 420/2P must be ordered for two-door enclosures.


No. of doors Individual chassis on two-door enclosures reference*Width (B)Height (A)

Total chassis reference*No. of rows

Automatic switch rail

Quantity No. of 18 mm modulesNo. of plates

For attachment to enclosures Distribution of rows

750 500 1 DLP 76 - 4 4 76 -

750 500 1 DLP 57 - 4 3 57 1

750 750 1 DLP 132 - 4 4 132 -

750 750 1 DLP 99 - 4 3 99 1

750 1000 2 - DLP 76 + DLP 76 4 + 4 4 + 4 152 -

DLP 57 + DLP 57 4 + 4 3 + 3 114 1 + 1

750 1250 2 - DLP 76 + DLP 132 4 + 4 4 + 4 208 -

DLP 57 + DLP 99 4 + 4 3 + 3 156 1 + 1

1000 500 1 DLP 114 - 6 6 114 -

1000 500 1 DLP 95 - 6 5 95 1

000 750 1 DLP 198 - 6 6 198 -

1000 750 1 DLP 165 - 6 5 165 1

1000 1000 2 - DLP 114 + DLP 114 6 + 6 6 + 6 228 -

DLP 95 + DLP 95 6 + 6 5 + 5 190 1 + 1

1000 1250 2 - DLP 114 + DLP 198 6 + 6 6 + 6 312 -

DLP 95 + DLP 165 6 + 6 5 + 5 260 1 + 1

1250 500 1 DLP 133 - 7 7 133 -

1250 500 1 DLP 114P - 7 6 114 1

1250 750 1 DLP 231 - 7 7 231 -

1250 750 1 DLP 198P - 7 6 198 1

1250 1000 2 - DLP 133 + DLP 133 7 + 7 7 + 7 266 -

DLP 114P + DLP 114P 7 + 7 6 + 6 228 1 + 1

1250 1250 2 - DLP 133 + DLP 231 7 + 7 7 + 7 364 -

DLP 114P + DLP 198P 7 + 7 6 + 6 312 1 + 1

1500 500 1 DLP 171 - 9 9 171 -

1500 500 1 DLP 152 - 9 8 152 1

1500 750 1 DLP 297 - 9 9 297 -

1500 750 1 DLP 264 - 9 8 264 1

1500 1000 2 - DLP 171 + DLP 171 9 + 9 9 + 9 342 -

1500 1000 2 - DLP 152 + DLP 152 9 + 9 8 + 8 304 -

1500 1250 2 - DLP 171 + DLP 297 9 + 9 9 + 9 468 1 + 1

1500 1250 2 - DLP 152 + DLP 264 9 + 9 8 + 8 416 1 + 1

DLP distribution system chassis

03_110_117_EN.indd 11203_110_117_EN.indd 112 2/4/08 12:58:182/4/08 12:58:18

85

40

2546

150

85

440

8585

40

85

40

45C-178C-mín.

40

16

C

3/113

Detail of the depth-adjustable rail using a graduated support included in the standard supply.

Covers that are quick fixing by pressure and removable using screwdriver.

Label for identifying circuits included in the standard supply.

FIG. 1

FIG. 2

Positioning the adjustable chassis at a depth of 25 mm.

* For enclosures with a transparent KT door, subtract 5 mm.

PLA Applications

(500)(1500)

DLP 171

(500)(1250)

DLP 133

(500)(1000)

DLP 114

(500)(750)

DLP 76

(750)(1500)

DLP 297

(750)(1250)

DLP 231

(750)(1000)

DLP 198

(750)(750)

DLP 132

(500)(1500)

DLP 152

(500)(1250)

DLP 114P

(500)(1000)

DLP 95

(500)(750)

DLP 57

(750)(1000)

DLP 165DLP 99

(750)(750)

(750)(1500)

DLP 264

(750)(1250)

DLP 198P

03_110_117_EN.indd 11303_110_117_EN.indd 113 2/4/08 12:58:182/4/08 12:58:18

3/114

Self-extinguishing plain cover to protect non-modular material.

c Colour RAL-7032.

c Easily machined.

c Quick mounting.

c 150 mm nominal height for 1 row.

2 mm thick mounting plate for fixing non-modular equipment, made of galvanised steel.

c Direct fixing to the adjustable support, which permits a depth adjustment of between 40 and 85 mm with respect to the cover.

c 150 mm nominal height for 1 row.

149

D

10×45°

E

PLA Applications

Plain cover

Mounting plate

Plate heightEnclosure width

(B)Reference D E

150 500 PMP500/DLP 361 149

150 750 PMP750/DLP 611 149

150 500 PMP500/2DLP 361 298

300 750 PMP750/2DLP 611 298

25 25

146

2113

D

To be coupled to nominal-width enclosures (B)

Reference D

500 CTL500/DLP 402

750 CTL750/DLP 652

500 CTL500/2DLP 402

750 CTL750/2DLP 652

03_110_117_EN.indd 11403_110_117_EN.indd 114 2/4/08 12:58:202/4/08 12:58:20

3/115

Earth or neutral bypass terminal blocks with insulating plinth.

Fixed to the back of the enclosure using the metal profile.


1 2

3 4

PLA Applications

Blanking plate



Reference Number of terminals 3 section in mm2

RBLZ/21656* 2 16 mm2 + 5 6 mm2

RBLZ/21686 2 16 mm2 + 8 6 mm2

RBLZ/216146 2 16 mm2 + 14 6 mm2

RBLZ/216296 2 16 mm2 + 29 6 mm2

Distribution bars

No. of bars No. of poles per bar Reference Figure No.

1 12 BDS 1/12 1

2 6 BDS 2/6 2

3 4 BDS 3/4 3

4 3 BDS 4/3 4

Blanking plate of self-extinguishing insulating material for total or partial coverage of the windows for automatic switches. Easily cut to the desired size.

ATP6/DTM 108 6

ATP24/DTM 432 24

ATP/UND 1100 Cut to size

No. of modulesLength (mm)Reference

03_110_117_EN.indd 11503_110_117_EN.indd 115 2/4/08 12:58:222/4/08 12:58:22

3/116

System of very robust 19” metal racks, to be coupled to all versions of PLA enclosures with dimensions indicated on the following page.

c Fixed and pivoting racks, permitting direct installation (using standardised perforations) of all types of 19” modular switchgear.

c Fixing the racks on the upper part and the sides of the corresponding enclosure, using SPLA vertical profiles, which must be ordered separately from 750 mm height enclosures. See tables on the next page.

c Both the fixed and the pivoting racks can be installed as partial racks in enclosures that are larger than the foreseen normal. See tables on the next page.

c Maximum load: 3 kg per unit, with a maximum of 40 kg for pivoting racks.

c Finish: polyester-epoxy RAL-7032 paint.

c Pivoting racks with opening to 120º, 5 mm key-operated double bar lock.

➀ Fixed rack BRF 17PLA fixed using the set of two vertical profiles SPLA 100.

➁ Pivoting rack BRP 16PLA fixed using the set of two vertical profiles SPLA 100.

➂ Pivoting rack BRP 7PLA installed as a partial rack in enclosure. PLA 1074KT fixed using the set of two vertical profiles SPLA 100.

➂

➁

➀

PLA Applications

System of 19” racks

For 19” accessories, consult the VDI catalogue.

Ref.: SB/PLA.

19” rack support and trays for two-door enclosures

03_110_117_EN.indd 11603_110_117_EN.indd 116 2/4/08 12:58:232/4/08 12:58:23

31.7

5

485

465

450

55

750

77

300

420

12.7

44.4

544

.45

8.5 x 8.5

750

31.7

512

.7

44.4

544

.45

420

465

450

8.5 x 8.5

325

44

3/117

BRF racks prepared to be coupled to all 750 mm width PLA enclosure models.From the 750 mm height enclosures, the set of two vertical profiles SPLA, indicated in the table, must be ordered.

BRF...

SPLA...

BRP racks prepared to be coupled to all 750 mm width and 420 mm depth PLA enclosure models.From the 750 mm height enclosures, the set of two vertical profiles SPLA, indicated in the table, must be ordered separately.

BRP...

SPLA...

PLA Applications

19” fixed rack

* Can be installed in taller enclosures as a partial rack, using the vertical profiles that correspond to the height of the enclosure. In all cases, the SPLA vertical profiles must be ordered separately.(1) It can also be installed in the 1250 mm enclosures, on the 750 mm side, using the SBPLA profiles.

Height (A)


Width (1) (B)No. of units Reference rack Set of two profiles

500* 750 8 BRF 8PLA* -

750* 750 12 BRF 12PLA* SPLA 75

1000* 750 17 BRF 17PLA* SPLA 100

1250* 750 21 BRF 21PLA* SPLA 125

1500* 750 26 BRF 26PLA SPLA 150

19” pivoting rack

* Can be installed in taller enclosures as a partial rack, using the vertical profiles that correspond to the height of the enclosure. In all cases, the SPLA vertical profiles must be ordered separately.

Height (A)


Width (B)No. of units Reference rack Set of two profiles

500* 750 7 BRP 7PLA* -

750* 750 11 BRP 11PLA* SPLA 75

1000* 750 16 BRP 16PLA* SPLA 100

1250* 750 20 BRP 20PLA* SPLA 125

1500* 750 25 BRP 25PLA SPLA 150

19” fixed rack 19” pivoting rack

03_110_117_EN.indd 11703_110_117_EN.indd 117 2/4/08 12:58:242/4/08 12:58:24

11

1 3 4

10 8a-8b

5

6712

2

9

3/118

PLD and ZD polyester enclosures and plinths for LV electrical distribution

Self-ventilating polyester enclosures, prepared to directly incorporate fuse blocks for electrical distribution, conforming to DIN standards.

03_118_119.indd 11803_118_119.indd 118 21/2/08 11:53:2021/2/08 11:53:20

3/119

8b Detail of the enclosure with central profile joined to the left door and one single lock.

8a Detail of the profile joined directly to the enclosure and locks on the left and right doors.

2 Back with system of bosses with inclusions for fixing various materials.

1 Insulating bakelite mounting plates in black RAL-9005. To be coupled directly to the back of the enclosure.

7 Lower side view once the cable entry opening has been accessed.

12 Detail of the opening of the blanking plate of the auxiliar outlet.

5 PLD enclosures are designed to be installed directly on the floor or on ZD plinths.

4 Self-ventilating IP43 profile in standard supply. Possibility of IP54 by applying the synthetic rubber seal.

3 Expandable metal nuts to be included in the prepared housings in the enclosures for fixing of equipment, rails, etc.

11 View of the front crossbar dismounted, thus facilitating access to the interior of the enclosure.

10 Set of two metal supports for fixing the enclosure directly to the floor.

9 Detail of the easily removable interior hinge and bosses located at the back and on the door for fixing various materials.

6 Folding upper front cover, easily accessible from the interior of the enclosure.

03_118_119.indd 11903_118_119.indd 119 21/2/08 11:53:2321/2/08 11:53:23

3/120

PLD-ZDPolyester enclosuresSelf-ventilated IP43IP54 watertight (EN 60529)

Applications

c Self-ventilated polyester enclosures, prepared to directly incorporate fuse

blocks for electrical distribution.

c Extremely versatile for any type of assembly.

c Self-extinguishing and easily machined material.

c High resistance to mechanical impacts, temperature and corrosive

environments.


c Resistance to the main chemical agents and corrosive atmospheres.


c Reversible door opening to more than 180º in every case.

c Internal hinges easily removed.

c Back of enclosure with a system of bosses equipped with M8 and M10

inclusions allowing direct fixing of the mounting plates, bar supports and/or

various materials that offers great versatility for carrying out any type of

assembly.

c Removable front crossbar that enables better access to the interior of the

enclosure.

c Canopy and body of the enclosure of equal perimeter enabling enclosures to

be coupled both laterally and posteriorly.

PLD-86/0

Hot-press moulded fibreglass-reinforced polyester enclosure in grey RAL-7032 (able to withstand weather conditions).

03_120_137_EN.indd 12003_120_137_EN.indd 120 2/4/08 12:59:322/4/08 12:59:32

3/121



c Conforms to general rules for empty enclosures established in IEC and

EN 62208.

c Degree of protection IP43/IK10.

c High resistance to mechanical impacts IK10 (20 J) conforming to IEC and

EN 62262.


c Extreme operating temperatures from –50 a 150 ºC.

c Suitable for double insulation mounting conforming to IEC 60439-1

(EN 60439-1).

Basic composition

c Open top with canopy.

c Completely closed base.

c Reversible door opening to more than 180º.

c Three-point lock, handle operated without catch.

c Front crossbar easily removable.

Optional accessories

c Designed to be directly fixed to the ground or on a plinth ZD.

c Possibility of installing APLD mounting plates and BPLDN racks.

c Equipped with a system of bosses in the interior for fixing light fixtures.

c Possibility of IP54 when using a JED gasket.

E: Screws that connect the entry to the connection.

External dimensions (mm) Enclosures

Mounting plates APLD

Plinth ZD

Maximum No. of fuse blocks

Height(A)

Width (B)

Depth(C)

Reference DIN sizeNo. of doors

No. of locks

D

850 465 320 PLD-85/00 00 1 1 360 APLD-85 ZD-53/00 3 + E

850 590 320 PLD-86/0 0 1 1 495 APLD-86 ZD-63/0 4 + E

850 785 320 PLD-88/1 1 1 1 690 APLD-88 ZD-83/1 6 + E

850 1115 320 PLD-812/2 2 2 1 - APLD-812 ZD-123/2 9 + E

850 1115 320 PLD-812/2C 2 2 2 - APLD-812 ZD-123/2 9 + E

03_120_137_EN.indd 12103_120_137_EN.indd 121 2/4/08 12:59:332/4/08 12:59:33

3/122

FIG. 1

PLD-85/00; 86/0; 88/1 PLD-812/2; 812/2C

D


Dimensions (mm)

1 M10 inserts for installing plates and fuse holder plinths or other material.

2 M6 inserts for fixing mounting plates, rails in general and other material.

3 Bosses prepared for M8 inserts for fixing adjustable plate supports, Ref.: TEX 8.

4 Housings for installing floor fixing supports, Ref.: SPLD. Permit the insertion of M8 nuts, Ref.: TE/PLD-M8 for fixing various material.

5 Lock on right and left door on model PLD-812/2C.

Interior canopy prepared for bosses for inserting nuts, Ref.: TEX 6 for fixing auxiliary material, lighting, etc.

03_120_137_EN.indd 12203_120_137_EN.indd 122 2/4/08 12:59:332/4/08 12:59:33

3/123

PLD-ZD Composition accessories

Hot-press moulded fibreglass-reinforced polyester plinths, in grey RAL-7032 (able to withstand extreme weather conditions).

c Self-extinguishing material; easily machined; high resistance to impacts, temperature and corrosive environments.

c Partially ground embedded plinths prepared for direct fixing to the PLD enclosure.

c Folding front cover, accessible from the interior.

c Bosses on the rear panel prepared for inserting nuts, Ref.: TEX 6 for M6 screws, allowing for fixing of the the neutral plate, rails and other material.

c The sides have an auxiliary outlet with a passing diameter of Pg 36 (48 mm), fitted with a plug.

c Adjustable metal interior profiles in U and L for cable fixing.

c Possibility to cut out the interior part of the side for cable passage.


Height (A)


Width (B) Depth (C)Reference To couple to enclosures

900 465 310 ZD-53/00 00 360 PLD-85/00

900 590 310 ZD-63/0 0 495 PLD-86/0

900 785 310 ZD-83/1 1 690 PLD-88/1

900 1115 310 ZD-123/2 2 - PLD-812/2; PLD-812/2C

DDIN size

ZD Plinths

Dimensions (mm)

ZD-53/00; 63/0; 83/1 ZD-123/2

03_120_137_EN.indd 12303_120_137_EN.indd 123 2/4/08 12:59:352/4/08 12:59:35

3/124

PLD-ZD Composition accessories

To be coupled directly to the door and the back of the enclosure, obtaining IP54.

c Manufactured in black synthetic rubber.

Sealing gasket

To couple to enclosures Reference

PLD-85/00 JED-85/00

PLD-86/0 JED-86/0

PLD-88/1 JED-88/1

PLD-812/2 and 2C JED-812/2

Direct-action standard lock, operated by a retractable handle.

Locks

CATCHES FOR LOCKS

Specifications ReferenceType of key

operation, Ref.:

Double bar lock LDB 5 TDB/PLD

Side triangle lock ∆ 8 mm LT-8 TT7/PLD

Lock with key type 405 TCL/PLD

Lock with reinforced key type

TLR/PLD

Manual lock TEM/PLD

Padlock

BCME/PL

Set of two metal supports for fixing the enclosure directly to the floor.

Ref.: SPLD.

KL

max.Enclosure reference

number

PLD-85/00 360 320 224

PLD-86/0 495 455 224

PLD-88/1 690 650 224

PLD-812/2 and 2C 1020 980 224

Mmax.

Floor fixing supports

03_120_137_EN.indd 12403_120_137_EN.indd 124 2/4/08 12:59:392/4/08 12:59:39

3/125

PLD-ZD Mounting accessories

To be coupled directly to the back of PLD enclosures.

c Insulating bakelite plates in black RAL-9005.

Possibility of depth adjustment. See notes on use of bosses 3 on page 3/122.

Mounting plates

ReferenceNo. of plates per

enclosure

Plate reference

D EFor attachment to enclosures Thickness

(mm)

PLD-85/00 1 APLD-85 356 304 5

PLD-86/0 1 APLD-86 481 429 5

PLD-88/1 1 APLD-88 676 624 5

PLD-812/2 and 2C 2 APLD-812* 448 396 5

* The reference includes the 2 plates.

Insulating rail in hot-pressed fibreglass-reinforced polyester, in grey RAL-7032.

c Direct lateral fixing to PLD enclosures.

c Possibility of directly fixing busbars.

Ref.: BPLDN.

Rack for fixing equipment

03_120_137_EN.indd 12503_120_137_EN.indd 125 2/4/08 12:59:402/4/08 12:59:40

3/126

PLD-ZD Current distribution accessories


Adjustable ties

White BlackL ∅

minimum∅

maximum

M

Reference Use

LZ25100 LN25100 100 2.5 1.6 22

LZ25200 LN25200 200 2.5 1.6 49

LZ35150 LN35150 150 3.5 1.6 35

LZ35200 LN35200 200 3.5 1.6 49

LZ35300 LN35300 300 3.5 1.6 75

LZ46150 LN46150 150 4.6 1.6 36

LZ46200 LN46200 200 4.6 1.6 49

LZ48270 LN48270 270 4.8 1.6 73

LZ46390 LN46390 390 4.6 1.6 109

LZ76390 LN76390 390 7.6 4.7 108

To tighten and cut the adjustable ties to size. They facilitate wiring and save time, preventing the packets of cables from loosening.



Tightening tools

Reference

MARK3 2.5 ÷ 4.8


Reference

MARK20 2.5 ÷ 4.8

MARK21 4.6 ÷ 7.6



Locking clips

Reference

SFC1 6 3.2 1

SFC2 6 1 2

FigureMax. panel

thickness mm∅ perforation

mm

SFC2 SFC1

Fig. 1 Fig. 2

03_120_137_EN.indd 12603_120_137_EN.indd 126 2/4/08 12:59:422/4/08 12:59:42

3/127


To use with soft materials: 7 mm Ø hole, or hard materials: 8 mm Ø hole. Ties up to 9 mm in width can be coupled. Material: black 6.6 nylon.

Ref.: LOK01.

Stud


Tie fixing support


C

KR6 12 18 9 M4 2.5 ÷ 4.8

KR8 14.5 25 12 M6 2.5 ÷ 7.6


Support heads


C

FH18 7.1 13.3 4 M4 2.5

FH30 9.5 17.9 4.7 M5 3.5

FH50 11.3 22.2 6.2 M6 4.7

03_120_137_EN.indd 12703_120_137_EN.indd 127 2/4/08 12:59:442/4/08 12:59:44

adhesive support

3/128





tiesD

MB3A 19.1 19.1 4.8 3.2 13.2 2.5 ÷ 3.5

MB4A 28.5 28.5 5.5 4 20.2 2.5 ÷ 4.8


Tie fixing support

Reference

LKC 2.5 7.6 M5


ties mm



Reference

LKM/HE 2.5 7.6 M5


ties mm

03_120_137_EN.indd 12803_120_137_EN.indd 128 2/4/08 12:59:452/4/08 12:59:45

3/129


2 versions, fixed and adjustable, ∅ from 5 to 25.4 mm. Material: black 6.6 nylon.


Reference∅ A

min. - max.B D EC

NX1 5 3.5 1 6.2 13.7

NX3 8 3.9 1 9.4 20.5

NX5 12 3.9 1 9.4 24

NX8* 14.3 ÷ 15.8 4 1.3 12.6 32

NX11 17.4 ÷ 20 4 1.3 12.6 37

NX14 22.2 ÷ 25.4 4.3 1.5 16 45

* The NX8 model only has 3 adjustment holes.

NX 1-3-5 NX 8-11-14

Insulated membrane glands made of PVC with entry that can be adjusted for cables.



Capacity

ECPC-3 1 25 21.5 18 5 3.2 13 5 a 18 Pg 9 a 11

ECPC-5 1 33 29.5 26 5 3.2 20 5 a 26 Pg 9 a 16

ECPC-6 1 43 38.5 36 5 3.2 22 5 a 36 Pg 9 a 21

ECPC-9 2 70 63 60 28 3 20 28 a 60 Pg 21 a 48

ECPC-15 2 98 90 87 28 3 23 28 a 87 Pg 21 a 48


Fig. 1 Fig. 2

03_120_137_EN.indd 12903_120_137_EN.indd 129 2/4/08 12:59:462/4/08 12:59:46

Ø A

Ø B

3/130



Protective sleeves


PC-1 15.2 12.7 Pg 9

PC-2 18.6 16 Pg 11

PC-3 20.4 17.8 Pg 13.5

PC-4 22.5 19.8 Pg 16

PC-5 28.3 25.3 Pg 21

PC-6 37 33.6 Pg 29

PC-7 47 43 Pg 36

Desig-nation

Ø exterior

SteelFlexible


Protective sleeves

Adjus. mem-brane glands

Plain plugsAdjustable mem-

brane glands

Flexible steel with

PVC


1 2 3 4


No. of conductors



Ø perforations to

4 EC-1 al EC-7

Pg 9 15.2 12.7 12.4 12 11.1 6 2.5 - - 16 14 ECPC-3 al ECPC-6 PC-1 - -

ECN-5 al ECN-10

10 4 2.5 EC-2 al EC-7 EC-1


25 ECN-5 al ECN-10 ECN-1

EC-3 al EC-7 EC-3


ECN-5 al ECN-10

EC-4 al EC-7


ECN-5 al ECN-10

EC-5 al EC-7 EC-5

Pg 21 28.3 25.3 24.7 23 23 70 25 16 10 29 27 ECPC-6 al ECPC-15 PC-5 ECPC-5 TC-4

ECN-6 al ECN-10 ECN-5

95 35 25 16 EC-6; EC-7 EC-6 TC-5


150 ECN-7; ECN-10 ECN-6

185 35 EC-7 EC-7


300 ECN-10

95 70 ECPC-9; ECPC-15

Pg 42 54 50 48 48 47 - 120 95 70 55 52.5 ECN-10 - - -

120 95 ECPC-9; ECPC-15

Pg 48 60 56 54.2 52.5 51.4 - 150 150 120 61 58 ECN-10 - - -


For more information consult the rules

03_120_137_EN.indd 13003_120_137_EN.indd 130 2/4/08 12:59:472/4/08 12:59:47

3/131



DIN17660); ring of tempered steel zinc dichromate; cap made of orange self-extinguishing polypropylene.






Reference

S.04 1 × 4 30 20 13 21 4

S.06 1 × 6 33 25 16 24 7

S.10 1 × 10 38 28 16 28 6

S.16 1 × 16 42 32 19 32 9

S.25/35 1 × 35 46 38 23 34 11

S.50 1 × 50 52 45 27 40 15

S.70 1 × 70 55 50 30 40 15

S.95/100 1 × 100 58 54 33 40 20


Sectionm/m2 A B C D E

03_120_137_EN.indd 13103_120_137_EN.indd 131 2/4/08 12:59:482/4/08 12:59:48

3/132

ReferenceSection Cable bypass (mm2)

Plate thickness (mm) Figure

BPCH 516 1.5 to 16 5 2

BPCH 550 1.5 to 50 5 2

BPCH 5120 16 to 120 5 2

BPCH 1016 1.5 to 16 10 1

BPCH 1050 1.5 to 50 10 1

BPCH 10120 16 to 120 10 1



The BBH terminals are made of a tinned, hot cast copper alloy and are suitable for connecting to a conductor of copper or aluminium indistinctly (bimetal).


Reference

BBH-29 6-50 -

BBH-29C* 6-50 -

BBH-30 10-95 -

BBH-31 16-150 -

BBH-32 50-240 -

BBH-29D 6-50 6-50

BBH-29DC* 6-50 6-50

BBH-30D 10-95 10-95

BBH-31D 25-150 16-150

BBH-32D 95-240 5-240


Reference

BBH-29P 6-50 -

BBH-29PC* 6-50 -

BBH-29DP 6-50 6-50

BBH-29DPC* 6-50 6-50



BBH-29 BBH-29D

BBH-29P BBH-29DP



1 2

03_120_137_EN.indd 13203_120_137_EN.indd 132 2/4/08 12:59:482/4/08 12:59:48

35590

7066

3/133

PLD-ZD Lighting accessories

Compact lamp


Lamp fixed with a magnet or

on 35 mm symmetrical LAM-75 220 V/16 A 220 V/50 Hz

DIN rail.


symmetrical DIN rail. LAC-75 220 V/16 A 220 V/50 Hz

L amp fixed with a magnet or

on 35 mm symmetrical LAM-75/120 120 V/15 A 120 V/60 Hz

DIN rail.


symmetrical DIN rail. LAC-75/120 120 V/15 A 120 V/60 Hz



c Consumption 11 W.







c Power: 11 W.

c Luminosity: 900 lm

c Lifespan: 10000 h

c Carcasa de plástico UL94 V0.


c IP20.

c Class I.

Slimline lamp





03_120_137_EN.indd 13303_120_137_EN.indd 133 2/4/08 12:59:502/4/08 12:59:50

396

67

100

500

3/134

PLD-ZD Lighting accessories

Dual lamp

1

2

3

4


Motion-activated



On/off switch with the possibility Magnetic, using screws LAMIN 220 V/50 Hz

of connecting door switch and/or (1) 35 DIN rail 2 LAMIN 120 120 V/60 H


LAMPO 220 V/50 Hz


Support for LAMDP, LAMIN, Adhesive or screws

LAMPO lamp 4 SOLAM

(1) DIN rail not provided.










c Consumption 60 W.



Incandescent lamp

Reference

LAI/OL 68

03_120_137_EN.indd 13403_120_137_EN.indd 134 2/4/08 12:59:512/4/08 12:59:51

3/135

To connect the inside of the enclosure with the exterior atmosphere and prevent condensation. Can be fixed onto the outside.

VM-25 VM-27

Ventilation devices


VM-27


PLD-ZD Natural ventilation accessories

03_120_137_EN.indd 13503_120_137_EN.indd 135 2/4/08 12:59:532/4/08 12:59:53

174

188 22 278 40

234

TEX 8 TEX 6 TEX 5

3/136

PLD-ZD Complementary accessories

PP-A models made of thermoplastic in grey RAL-7035.


For holding DIN A3-A4 or A5-sized plans.

Document pocket


Plan size

A4 PP-A4

A5 PP-A5

Reference

Insulated

Expandable metal nuts to be included in the prepared housings in the enclosures for fixing of equipment, rails, etc.

Specifications Reference

M5 TEX 5

M6 TEX 6

M8 TEX 8

Expandable nuts

03_120_137_EN.indd 13603_120_137_EN.indd 136 2/4/08 12:59:532/4/08 12:59:53

3/137

One of the main applications is the LV distribution. For this reason, they are prepared for the incorporation of fuse blocks, insulators and busbars.

PLD enclosure equipped with:

c 3F + N 50 × 10 copper busbar.

c Floor fixing supports SPLD.

c Prepared for installing fuse block (not included).

c Triangle lock.

PLD enclosure equipped with:

c Plinth ZD.

c 3F + N 50 × 10 copper busbar.

c Prepared for installing fuse block (not included).

c Triangle lock.

(Bases not included)

Reference Dimensions (mm) Capacity, vertical s/c III*

PLZD-85/B 1720 × 465 × 320 3+E

PLZD-86/B 1720 × 590 × 320 4+E

PLZD-88/B 1720 × 785 × 320 6+E

PLZD-812/B 1720 × 1115 × 320 9+E

PLZD-812-C/B 1720 × 1115 × 320 9+E

E: screws that connect the entry to the connection.

Distribution enclosures in BT

PLD-B enclosures

PLZD-B enclosures

E: screws that connect the entry to the connection.

Reference Dimensions (mm) Capacity, vertical s/c III*

PLD-85/B 850 × 465 × 320 3+E

PLD-86/B 850 × 590 × 320 4+E

PLD-88/B 850 × 785 × 320 6+E

PLD-812/B 850 × 1115 × 320 9+E

PLD-812-C/B 850 × 1115 × 320 9+E

PLD-ZD Applications

SPECIAL ARTICLES ON REQUEST

03_120_137_EN.indd 13703_120_137_EN.indd 137 2/4/08 12:59:562/4/08 12:59:56

Date post:	10-Dec-2015
Category:	Documents
Upload:	mikcomi
View:	29 times
Download:	3 times

Schneider PLA Ormani

Documents