PARTS MANUALSECTION 40
Published 08/15 - Revised 08/18 MATERIAL HANDLING PARTS MANUAL
BSR8 HAY RAKEBSR10 HAY RAKE BSR12 HAY RAKE
SUSPENSION RAKE
©2009 Alamo Group Inc.
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in pro-cessing purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organiza-tion ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:
BUSH HOG2501 Griffin Ave. Selma, AL 36703www.bushhog.comContact Us800-304-2836
To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-mindedoperator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer hasdesigned this implement to be used with all its safety equipment properly attached to minimize the chance ofaccidents.
BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rulesof safety and common sense!
WARRANTY INFORMATION:Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWarranty Card and on the Warranty Form that you retain.
LIMITED WARRANTY
Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized BushHog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year fornon-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Theobligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defectiveparts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warrantyperiod, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hogdealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which areclaimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESBush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied orexpressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale oruse of the items warranted. Such incidental and consequential damages shall include but not be limited to:transportation charges other than normal freight charges; cost of installation other than cost approved by BushHog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental ofsubstitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or partsresulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgementof Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in thesole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, wornblades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in thecompany’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITEDWARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE INWRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA36703.
Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.
MAKE CERTAIN THE WARRANTY
HAS BEEN FILED WITH BUSH HOG
SELMA, ALABAMA
MODEL NUMBER ________________________________
SERIAL NUMBER ________________________________
DATE OF RETAIL SALE ___________________________
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
TABLE OF CONTENTSBSR SUSPENSION RAKE
ITEM PAGE NUMBER
Center Frame & Related Parts - BSR8 & BSR10. . . . . . . . . . . . . . . . . . . .40-1-2, 40-1-3
Center Frame & Related Parts - BSR12 . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-4, 40-1-5
RH Wheel Arm Assy, Short Arm Assy and Wing Frame . . . . . . . . . . . . . . .40-1-6, 40-1-7
LH Wheel Arm Assy, Short Arm Assy and Wing Frame . . . . . . . . . . . . . . .40-1-8, 40-1-9
Wheels & LH & RH Rake Arm Assembly . . . . . . . . . . . . . . . . . . . . . . . .40-1-10, 40-1-11
Rake Arm Hub & Spindle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-12
Hydraulic Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-1-13
Leveling Valve Kit (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-13
Hydraulic Cylinder - Kicker Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-14, 40-1-15
Hydraulic Cylinder - Wing Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-16
Kicker Wheel Kit (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-17
Hydraulic Kit, Kicker Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-18
Rake Wheel & Tire Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-19
Led Light Kit (Rear Light Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-20
Reduced Ground Pressure Cam Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-21
Ground Pressure Cam Kit w/Dowel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-22
Wing Set Plate Slotted Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-23
40-1-1
40-1-2
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
1816
1719
203
32
21
22
4
15
14
10
8
5
9
7
6
12
13
11
1E
NH
AN
CE
MO
DU
LE(L
ED
LIG
HT
KIT
)
23
25
2423
26
27
CENTER FRAMEAND RELATED PARTS
MODELS BSR8 & BSR10
40-1-3
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
Item Part No. Description Qty.
1 50072845 Center Frame Weldment 1
2 50073508 Decal, Haymaker 2
3 D617 Decal, Oil Leak High Pressure 2
4 50065309 Decal, Bush Hog 2
5 50078238 Tongue w/Decals, Modified 1
6 50073512 Decal, Important Chain 1
7 50073507 Decal, Warning Speed 1
8 D859 Decal, Genuine Parts Warning 1
9 50074260 Decal, Model - BSR Series 2
10 50072954 Hitch Weldment 1
11 50074816 Hitch Pin Assembly 2
12 20558BH Lynch Pin, 7/16” x 2” 2
13 ------- Capscrew, 5/8” x 2” Gr 5 4
14 9162000 Locknut, 5/8” Gr C 4
15 94359 Sign, SMV 1
16 2438621 Bracket, Spade - SMV Mounting 1
17 1160807 Capscrew, 1/4” x 7/8” Gr 5 2
18 15905 Lockwasher, 1/4” 2
19 15531BH Hex Nut, 1/4” 2
20 50035829 Tube, Owner’s Manual 1
21 50080009 Jackstand Assembly 1
22 ------- Machine Screw, Slt Pan Hd, #10 x 1 2
23 17020600 Flatwasher, #10 4
24 44520BH Locknut, #10 2
25 50074259 Decal, Made in USA 2
26 91074 Safety Tow Chain 1
27 D884 Decal, Warining - Jack Capacity 1
CENTER FRAME-MODIFIEDAND RELATED PARTS
MODELS BSR8 & BSR10
40-1-4
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
1816
1719
20
2425
2627
32
1
3
21
4
13
14
23
13
14
10
5
31
9
7
6
12
11
11
EN
CH
AN
CE
MO
DU
LE(L
ED
LIG
HT
KIT
)
32
29
30
28
22
15
28
8
CENTER FRAMEAND RELATED PARTS
MODELS BSR12
40-1-5
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
CENTER FRAMEAND RELATED PARTS
MODELS BSR12
Item Part No. Description Qty.
1 50072845 Center Frame Weldment 1
2 50073508 Decal, Haymaker 2
3 D617 Decal, Oil Leak High Pressure 2
4 50065309 Decal, Bush Hog 2
5 50078238 Tongue w/Decals, Modified 1
6 50073512 Decal, Important Chain 1
7 50073507 Decal, Warning Speed 1
8 D859 Decal, Genuine Parts Warning 1
9 50074260 Decal, Model - BSR Series 2
10 50072954 Hitch Weldment 1
11 50074816 Hitch Pin Assembly 2
12 20558BH Lynch Pin, 7/16” x 2” 2
13 ------- Capscrew, 5/8” x 2” Gr 5 8
14 9162000 Locknut, 5/8” Gr C 8
15 94359 Sign, SMV 1
16 2438621 Bracket, Spade - SMV Mounting 1
17 1160807 Capscrew, 1/4” x 7/8” Gr 5 2
18 15905 Lockwasher, 1/4” 2
19 15531BH Hex Nut, 1/4” 2
20 50035829 Tube, Owner’s Manual 1
21 50080009 Jackstand Assembly 1
22 50073481 Assembly, Tongue Extension 1
23 50074146 Plate, Cylinder Lug 1
24 20103 Capscrew, 1” x 3” Gr 5 4
25 ------- Spacer, Cylinder 2
26 9163200 Locknut, 1” Gr C 4
27 ------- Machine Screw, Slt Pan Hd, #10 x 1 2
28 17020600 Flatwasher, #10 4
29 44520BH Locknut, #10 2
30 50074259 Decal, Made in USA 2
31 91074 Safety Tow Chain 1
32 D884 Decal, Warning - Jack Capacity 1
40-1-6
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
4912
1310
46
247 R
ight
Sid
e D
ual L
ED
Lam
p(L
ED
Lig
ht K
it)
11
1
3233
3231
45
14
2
1626
15
36
7
37
47 48
47
4836
415
2135
20
19
2927
1724
23
25
26
2230 18
5
38
34
39
9
38
40
50
1533
43
2826
26341
42
26
26
44
31
52
51Sp
ring
Mou
nt P
atch
Kit
Req
uire
d on
ly fo
r H
igh
Hou
r Rak
es8
RIGHT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS
MODELS BSR8, BSR10 & BSR12
40-1-7
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
Item Part No Description Qty
1 50078208 Wheel Arm Weldment, RH 1
2 50073080 Bushing, Rake Pivot 2
3 50031212 Reflector, Amber, 2” x 9” 2
4 50031214 Reflector, Red 1
5 50073078 Hub & Spindle Assy, Rake Wheel 1
6 45187BH Capscrew, 1/2” x 3-1/2” Gr 5 1
7 15554 Locknut, 1/2” 1
8 50073496 Decal, Ground Pressure- RH 1
9 50073077 Wheel & Tire Assembly, Rake 1
10 50078206 Cam Assembly, RH 1
11 50017304 Pin, Lynch 1
12 50078203 Pin, Dowel 3/8” x 2-1/2” 1
13 50073510 Decal, RH 1
14 50076440 Pin Assembly, Pivot 1
15 1273BH Pin, Presto 9 Ga x 3” D Plated 3
16 50072918 Pin Assembly, Pivot Arm Lock 1
17 7977 Hub Assembly 1
18 50073BH Bearing, Cone Roller 1
19 50076BH Bearing, Cone Roller 1
20 7967 Seal, Triple Lip 1
21 50072962 Spindle, Single - Rake 1
22 15920 Flatwasher, 3/4” 1
23 120BH Hex Nut, Slotted 3/4”-16 UNF 1
24 121BH Cap, Hub 1
25 296 Pin, Cotter 1/8” x 1-1/2” 1
26 449BH Grease Fitting 6
27 15445 Bolt 1/2”-20UNF x 1-5/8” 5
28 15515BH Nut 1/2” -20UNF 5
Item Part No Description Qty
29 14-6-197 Bearing Cup 1
30 14-6-198 Bearing Cup 1
31 20063 Capscrew, 1” x 6-1/2” Gr 5 3
32 15908BH Flatwasher, 1” Hard 4
33 9163200 Locknut, 1” Gr C 3
34 50073519 Short Arm Assy, RH w/Decals 1
35 D628 Decal, Crushing Hazard 1
36 50073511 Decal, Important Transport Latch 1
37 50076179 Roll Pin, 1/2” x 3” 1
38 50072951 Pin Assembly, Wing Angle 2
39 50072895 Wing Arm Adjustment Assembly 1
40 45328BH Capscrew, 3/4” x 6” Gr 8 2
41 15921 Flatwasher, 3/4” SAE 2
42 19517 Hex Nut, 3/4” 2
43 50078204 Wing Set Plate Weldment 1
44 50073504 Wing Frame Weldment - RH 1
45 50073087 Cylinder, Hyd. 2.5” Bore x 12” Str. 1
46 44186BH Capscrew, 1/4” x 1” Gr 5 4
47 15918BH Flatwasher, 1/4” 8
48 15608 Locknut, 1/4” 4
49 50074735 Cable Clamp 2
50 50077995 Nord Washer 1
51 50078220 Spring Mount Patch Kit 8 Wheel 1
50078221 Spring Mount Patch Kit 10 Wheel 1
50078222 Spring Mount Patch Kit 12 Wheel 1
52 50078219 Spring Pad Gusset 1
RIGHT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS
MODELS BSR8, BSR10 & BSR12
40-1-8
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
52
51Sp
ring
Mou
nt P
atch
Kit
Req
uire
d on
ly fo
r H
igh
Hou
r Rak
es
928
24
25
2318 30
1727
2919
205
26
1012 132
15
3536
3831
26
40
33
5015
43
3938
26
44
3
42
41
2626
45
14
211
3437 48
47 26
156
213 7
16 49
498
4
47
46
32
33
3132
1
Left
Sid
e D
ual L
ED
Lam
p(L
ED
Lig
ht K
it)
LEFT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS
MODELS BSR8, BSR10 & BSR12
40-1-9
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
Item Part No Description Qty
1 50078209 Wheel Arm Weldment, LH 1
2 50073080 Bushing, Rake Pivot 2
3 50031212 Reflector, Amber, 2” x 9” 2
4 50031214 Reflector, Red 1
5 50073078 Hub & Spindle Assy, Rake Wheel 1
6 45187BH Capscrew, 1/2” x 3-1/2” Gr 5 1
7 15554 Locknut, 1/2” 1
8 50073497 Decal, Ground Pressure- LH 1
9 50073077 Wheel & Tire Assembly, Rake 1
10 50078207 Cam Assembly, LH 1
11 50017304 Pin, Lynch 1
12 50078203 Pin, Dowel 3/8” x 2-1/2” 1
13 50073509 Decal, LH 1
14 50076440 Pin Assembly, Pivot 1
15 1273BH Pin, Presto 9 Ga x 3” D Plated 3
16 50072918 Pin Assembly, Pivot Arm Lock 1
17 7977 Hub Assembly 1
18 50073BH Bearing, Cone Roller 1
19 50076BH Bearing, Cone Roller 1
20 7967 Seal, Triple Lip 1
21 50072962 Spindle, Single - Rake 1
22 15920 Flatwasher, 3/4” 1
23 120BH Hex Nut, Slotted 3/4”-16 UNF 1
24 121BH Cap, Hub 1
25 296 Pin, Cotter 1/8” x 1-1/2” 1
26 449BH Grease Fitting 6
27 15445 Bolt 1/2” -20UNF x 1-5/8” 5
Item Part No Description Qty
28 15515BH Nut, 1/2”-20UNF 5
29 14-6-197 Bearing Cup 1
30 14-6-198 Bearing Cup 1
31 20063 Capscrew, 1” x 6-1/2” Gr 5 3
32 15908BH Flatwasher, 1” Hard 4
33 9163200 Locknut, 1” Gr C 3
34 50073518 Short Arm Assy, LH w/Decals 1
35 D628 Decal, Crushing Hazard 1
36 50073511 Decal, Important Transport Latch 1
37 50076179 Roll Pin, 1/2” x 3” 1
38 50072951 Pin Assembly, Wing Angle 2
39 50072895 Wing Arm Adjustment Assembly 1
40 45328BH Capscrew, 3/4” x 6” Gr 8 2
41 15921 Flatwasher, 3/4” SAE 2
42 19517 Hex Nut, 3/4” 2
43 50078204 Wing Set Plate Weldment 1
44 50073503 Wing Frame Weldment - LH 1
45 50073087 Cylinder, Hyd. 2.5” Bore x 12” Str. 1
46 44186BH Capscrew, 1/4” x 1” Gr 5 4
47 15918BH Flatwasher, 1/4” 8
48 15608 Locknut, 1/4” 4
49 50074735 Cable Clamp 2
50 50077995 Nord Washer 1
51 50078220 Spring Mount Patch Kit 8 Wheel 1
50078221 Spring Mount Patch Kit 10 Wheel 1
50078222 Spring Mount Patch Kit 12 Wheel 1
52 50078219 Spring Pad Gusset 1
LEFT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS
MODELS BSR8, BSR10 & BSR12
40-1-10
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
18
15, 1
6
1921
17
22
20
30
2716
5
2
3
264 27 28 29
LH
WIN
G
FR
AM
E
RH
WIN
G
FR
AM
E
10A
4 712
24
23
2510
B,
10C
9
14
2423
2510
B,
10C
9
13
8 10B
,10
C25
23
2410
B,
10C
811
25
23
24610
A4
15
1
5
34
26
2729 28
6
10A
10A
7
WHEELS & LH & RH RAKE ARMASSEMBLY w/RELATED PARTSMODELS BSR8, BSR10 & BSR12
40-1-11
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
WHEELS & LH & RH RAKE ARMASSEMBLY w/RELATED PARTSMODELS BSR8, BSR10 & BSR12
Item Part No. Description Qty Qty Qty
BSR8 BSR10 BSR12
1 50075265 Assembly, Rake Arm - RH 4 5 6
2 50075266 Assembly, Rake Arm - LH 4 5 6
3 50073514 Rake Wheel Hub & Spindle Assembly 8 10 12
4 50073061 Bushing, Rake Arm 16 20 24
5 50073485 Spring, Rake Arm 8 10 12
6 50072964 Arm Stop Assembly, RH 4 4 5
7 50072978 Arm Stop Assembly, LH 4 4 5
8 50072973 Lock Pin Assembly, Front Stop - RH - 1 1
9 50072976 Lock Pin Assembly, Front Stop - LH - 1 1
10A 53065 Spiral Pin, 3/8” x 2-1/2” 8 8 10
10B 20327 (OUTER) Roll Pin, 3/8” x 2-1/2” - 2 2
10C 45325BH (INNER) Roll Pin, 7/32” x 2-1/2” - 2 2
11 50072905 Weldment, RH Wing Frame - BSR10 - 1 -
12 50072969 Weldment, LH Wing Frame - BSR10 - 1 -
13 50072970 Weldment, RH Wing Frame - BSR12 - - 1
14 50072908 Weldment, LH Wing Frame - BSR12 - - 1
15 50075555 Assy, Rake Wheel - RH 4 5 6
S/N 1HCKR1171500069 & Below
50075253 Assy, Rake Wheel - RH 4 5 6
S/N 1HCKR1171500070 & Above
16 50075554 Assy, Rake Wheel - LH 4 5 6
S/N 1HCKR1171500069 & Below
50075252 Assembly, Rake Wheel - LH 4 5 6
S/N 1HCKR1171500070 & Above
17 50074099 Flange, Rake Wheel 8 10 12
S/N 1HCKR1171500069 & Below
50075254 Flange, Rake Wheel 8 10 12
S/N 1HCKR1171500070 & Above
18 50074098 Ring, Rake Wheel 8 10 12
S/N 1HCKR1171500069 & Below
50075255 Ring, Rake Wheel 8 10 12
S/N 1HCKR1171500070 & Above
19 50074097 Finger, Rake Wheel (Set of 40) 320 400 480
S/N 1HCKR1171500069 & Below
50075256 Finger, Rake Wheel (Set of 40) 320 400 480
S/N 1HCKR1171500070 & Above
20 50074096 Plate, Clamp - Rake Wheel 80 100 120
S/N 1HCKR1171500069 & Below
50075257 Plate, Clamp - Rake Wheel 80 100 120
S/N 1HCKR1171500070 & Above
21 70631C4 Bolt, M10 x 1.5 x 25 160 200 240
22 50075259 Nut, M10 160 200 240
23 50072980 Assembly, Front Stop Lock Pin - 2 2
24 1273BH Pin, Presto 9 GA x 3” D Plated - 2 2
25 50031212 Reflector, Amber 2” x 9” - 2 2
26 1161010 Capscrew, 5/16” x 1” Gr 5 8 10 12
27 15915BH Flatwasher, 3/8” 56 70 84
28 15907BH Flatwasher, 5/16” 8 10 12
29 15528 Hex Nut, 5/16” 8 10 12
30 8151200 Hex Nut, 3/8” 48 60 72
40-1-12
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
RAKE ARM HUB & SPINDLE ASSEMBLY
Item Part No. Description Qty.
50073514 Rake Arm Hub & Spindle Assy 1
1 50074256 Seal, Hub (N906282) 1
2 50072962 Spindle, Single - Rake 1
3 21020416 Pin, Cotter 1/8” x 1-3/4” 1
4 50074101 Washer 1
5 50074102 Hub Cap 1
6 50074103 Nut, Slotted 3/4”-16UNF 1
7 50074104 Bearing Cone (L44649) 2
8 50074100 Protector, Seal 1
9 50074257 Hub w/Studs & Cups 1
10 50074276 Rake Stud, 3/8”-16UNC x 1.25 6
11 170BH Bearing Cone, 1” Bore x .5 2
40-1-13
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
CYL ROD END
CYL BASEEND
1
2
2
1
3
3
4
4
5
5
6
6
HYDRAULIC KIT50073523
Item Part No. Description Qty.
1 14-40-98 Elbow, 90° 4
2 50068458 Restrictor 2
3 53330BH Assembly, Hydraulic Hose, 42” 4
4 53339BH Tee, G-Flare 2
5 24-6-434 Adapter, Hyd. Str. 1/2” Male NPT x 9/16” M JIC 2
6 50015063 Assembly, Hydraulic Hose, 196” 2
Item Part No. Description Qty.
1 50077055 Leveling Valve Assembly 1
2 50077057 Cartridge Assembly 2
3 53340BH Hydraulic Adapter 3
4 14-40-98 90º Elbow 1
5 6050072 Swivel Nut Tee 1
6 97339 Swivel Nut Branch Tee 1
7 ------- Instruction Sheet (50077046) 1
8 50077041 Leveling Valve Kit 1
qww
e
e
r
t
yi LEVELING VALVE KIT (Optional)
(Use to raise both arms at the same time)
40-1-14
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
2
98
14
1213
46 7
3
12
5
10
11
9
8
15
1
HYDRAULIC CYLINDER - KICKER WHEELBailey
(Replaced by Monarch)
Item Part No. Description Qty.
1 50074129 Assembly, Hydraulic Cylinder 1
2 ------- Clevis Cap 1
3 ------- Rod Cap 1
4 ------- Piston 1
5 ------- Rod, 1.125” Dia 1
6 ------- Cylinder Tube 1
7 ------- Tie Rod 4
8 ------- Pin, 1” Dia 2
9 ------- Cotter Pin, 3/16” x 1-1/2” 4
10 ------- Rod Clevis 1
11 ------- Set Screw 1
12 ------- Hex Nut 8
13 ------- Hex Nut 1
14 ------- Plug, 3/4” 1
15 50074138 Seal Kit 1
40-1-15
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
2
98
14
1213
46 7
3
12
5
10
11
9
8
15
1
916
HYDRAULIC CYLINDER - KICKER WHEELMonarch
(Replaces Bailey)
Item Part No. Description Qty.
1 50079045 Assembly, Hydraulic Cylinder 1
2 ------- Clevis Cap 1
3 ------- Rod Cap 1
4 ------- Piston 1
5 ------- Rod, 1.125” Dia 1
6 ------- Cylinder Tube 1
7 ------- Tie Rod 4
8 ------- Pin, 1” Dia 2
9 ------- Cotter Pin, 3/16” x 1-1/2” 4
10 ------- Rod Clevis 1
11 ------- Bolt 1
12 ------- Hex Nut 8
13 ------- Hex Nut 1
14 ------- Plug, 3/4” 1
15 ------- Hex Nut 1
16 50079046 Seal Kit 1
40-1-16
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
2
98
14
1213
4
6 7
3
12
5
10119 8
15
1
HYDRAULIC CYLINDER - WING LIFT
Item Part No. Description Qty.
1 50073087 Assembly, Hydraulic Cylinder 1
2 ------- Clevis Cap 1
3 ------- Rod Cap 1
4 ------- Piston 1
5 ------- Rod, 1.125” Dia 1
6 ------- Cylinder Tube 1
7 ------- Tie Rod 4
8 95425 Pin, 1” Dia 2
9 ------- Cotter Pin, 3/16” x 1-1/2” 4
10 50077191 Rod Clevis 1
11 ------- Set Screw 1
12 ------- Hex Nut 8
13 ------- Hex Nut 1
14 ------- Plug, 3/4” 1
15 50073528 Seal Kit 1
40-1-17
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
KICKER WHEEL KIT (OPTIONAL) - (Includes 50074130 Hyd. Kit)50074095
19
18
13
14
815
212
1411
7
754
4
7
9
6
1 10
13
13
3
16
17
Item Part No. Description Qty.
1 50074105 Weldment, Kicker Main 1
2 50074113 Bracket, Kicker Slide 1
3 50074118 Carrier, Rake Wheel 1
4 50073061 Bushing, Rake Arm 2
5 20570 Flatwasher, 1-1/4” SAE 1
6 53065 Pin, Spirol 3/8” x 2-1/2” 1
7 449BH Fitting, Grease 1/4-28 UNF Str. 3
8 15908BH Flatwasher, 1” Hard 1
9 45196BH Capscrew, 1/2” x 4” Gr 5 2
10 45104 Locknut, 1/2” Gr C 2
11 50079045 Cylinder, Tie Rod, 2” Bore x 8” Stroke x 1.125” Rod 1
12 1273BH Pin, Presto 9 Ga x 3” D 1
13 50074125 Shackle, Anchor 3
14 50074127 Stay, Spring 2
15 50074128 Spring, Kicker 1
16 50074126 Turn Buckle (5/16” x 18”), 9” Closed x 4.5” Adjust. 1
17 50075555 Assembly, Rake Wheel - RH 1
S/N 1HCKR1171500069 & Below
50075253 Assembly, Rake Wheel - RH 1
S/N 1HCKR1171500070 & Above
18 45063 Flatwasher, 3/8” 6
19 45073 Hex Nut, 3/8” 6
20 ------- Hyd. Kit, Kicker Wheel (50074130) [Not Shown] 1
2
1
3
5
6
4
40-1-18
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
HYDRAULIC KIT, KICKER WHEEL50074130
Item Part No. Description Qty.
1 25H46118 Hose Assembly, Hydraulic - 25” Lg 1
2 25H41146 Hose Assembly, Hydraulic - 31” Lg 1
3 50074133 Tee, Male Branch, 9/16”-18 MJIC x 9/16”-18 MJIC x 3/4”-16 MORB 1
4 50074134 Tee, Male Branch, 9/16”-18 MJIC x 9/16”-18 MJIC x 3/8” NPT 1
5 50074132 Valve, Hydraulic Ball 1
6 50074135 Adaptor, 3/4”-16 MORB x 3/8” NPT 1
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL March, 2014
RAKE WHEEL & TIRE ASSEMBLY
Item Part No. Description Qty.
1 50073077 Assembly, Rake Wheel & Tire 1
2 50073075 Rim, 15 x 5.0 BW Rolled 5-0.53” 1
3 50073076 Tire, ST205/75 D15 K550 6P TL 1
2
3
1
40-1-19
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
LED LIGHT KIT (REAR LIGHTS ONLY)50074720
Item Part No. Description Qty.
50074720 LED Light Kit 11 50072057 Module, Enhance 1
2 50074721 Main Harness (7 Pin, 16’ Long) 1
3 50074725 Wishbone Harness (8’ Long) 2
4 50074723 Dual LED Ag Lamp, Left Side, Amber/Red 1
5 50074724 Dual LED Ag Lamp, Right Side, Red/Amber 1
6 50072062 Lens, Red Replacement 2
7 50072063 Lens, Amber Replacement 2
8 50072064 Cover, Black Replacement Lens 4
9 ------- Slt Pn Hd Mach Screw, #10 x 1” 2
10 17020600 Flatwasher, #10 3
11 44520BH Locknut, #10 2
12 44186BH Capscrew, 1/4” x 1” Gr. 5 8
13 15918BH Flatwasher, 1/4” 16
14 15608 Locknut, 1/4” Gr. C 8
15 50074735 Clamp 4
40-1-20
7
815
1312
4 13
6
14
1
9
10
10
11
2
3
13
1215
8
7
5
6
13
14
Left Side
Right Side
Wiring Harnesses
40-1-21
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
REDUCED GROUND PRESSURE CAM KIT(For Earlier Models w/Too Much Ground Pressure)
Item Part No. Description Qty.
50074277 Reduced Ground Pressure Cam Kit, Ø4.75” 1
1 50074273 Cam Assembly, Ø4.75”, RH 1
50074274 Cam Assembly, Ø4.75”, LH 1
2 ------- Down Pressure Cam, Ø4.75” 1
3 50073510 Decal, RH 1
50073509 Decal, LH 1
4 20327 Roll Pin, 3/8” x 2-1/2” 1
5 45325BH Roll Pin, 7/32” x 2-1/2” 1
2
3
45
1
40-1-22
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
GROUND PRESSURE CAM ASSEMBLY KIT w/DOWEL
Item Part No. Description Qty.
50080677 Ground Pressure Cam Assembly Kit w/Dowel 1
1 50078206 Cam Assembly, RH 1
50078207 Cam Assembly, LH 1
2 ------- Down Pressure Cam, Dowel Pin 1
3 50073510 Decal, RH 1
50073509 Decal, LH 1
4 50078203 Dowel Pin, 3/8” x 2-1/2” 1
2
3
4
1
40-1-23
BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018
WING SET PLATE SLOTTED KIT(For Earlier Models Having Trouble Leveling Rake Arms)
Item Part No. Description Qty.
1 50078622 Wing Set Plate Slotted Kit 1
2 50078204 Wing Set Plate Weldment, Slotted 2
3 50077995 Nord-Lock, 3/4” 2
2
3
1