® RAZOR-BACK

Secondary Belt Cleaner

®Razor-Back secondary belt cleaner features tough self-adjusting replaceable tungsten carbide blades (non-carbide also available) for extremely effective belt cleaning.

• - tungsten carbide blades provides and maintains Longwearing Abrasion Resistant a great cleaning edge against the belt.

• - tension each individual blade to the belt for aImpact Absorbing Tension Cushions controlled and effective belt cleaning across the entire width of the belt.

• - allows for an installation that requires less then 9” of clearance Compact Design to be installed and maintained.

• - The Razor-Back can be installed on belts with me-Mechanical Splices? No Problem ®

chanical splices, due to the laid-back wiping blade angle and impact- absorbing tensioning cushions, allowing the mechanical splices to pass without damaging the belt cleaner or the splice.

• - Available with ™ ™ ™Bolt-Up , Duo-Spring , or Spring-Shoc Tensioning Systems

• - Available with Optional Spray-Bar. Spray nozzle sizes can be customized for any desired spray pattern and water pressure.

PRODUCT SPECIFICATIONS

Maximum Belt Speed - 1000 fpm (5.0 m/sec)

Application Coal Fired Power Plants, Hard Rock Mining, -

Steel Mills, Iron Ore, Aggregate and Mineral

(Phosphate, Potash, Salt) Mining.

Shown with ™Duo-Spring

Tensioner

1

2

3

4

5

6

7

1. Mounting Bracket

2. Slide Block

3. Thru-Hole Spring Bushing

4. Compressions Spring

5. Thread Push-Up Plate

6. Push-Up ACME Adjustment

7. Push-Up Spring Bushing

Other Available Tensioners

®RAZOR-BACK ™ Also available with Spring-Shoc Tensioner

™Spring-Shoc Secondary Tensioner ®developed by ASGCO “Complete Conveyor

Solutions”, utilizes a unique patent pending mounting plate that allows the cleaning

blade to be spring tensioned in either a pull-up or push-up position. This specially

designed configurability features two different mounting options that leave extra

clearance above or below the bracket where necessary.

Available Blade Tips

F-Tip C-Tip V-Tip UrethaneBlade

XC Ceramic Blade

™Duo-Spring ™Bolt-Up

®Razor-Back with Spray Bar®Razor-Back with Spray Bar is a secondary belt cleaner that uses a row of spray nozzles to spray

a fine sharp stream of water at a 30° degree angle onto the conveyor belt where the carry-back material is difficult to remove. Water is applied to the belt in an overlapping spray pattern which places the particles into a fluid suspension, while moistening the belt. The blades of the Razor-

®Back with Spray Bar are then able to make consistent contact with the conveyor belt surface to remove nearly 98% or more of bulk material coarse carry-back.

Advantages• Lubricate the conveyor - belt/cleaners interface and require much lighter tensioning.• Fully adjustable sprays - are built in enabling installation in the tightest of spaces.• Performance - is improved by a minimum of 75% over similar dry systems and maintenance is reduced because of the lubricating action of the water.• Customized spray nozzle - can be sized for any desired spray pattern and water pressure.• - can be replaced which provides a long service life with a high level Tungsten carbide tips of resistance to impact damage and/or acid leaching.

®Razor-Back

™with Bolt-Up Tensioner and Spray Bar

Part NumberBelt Width Wt.

Lbs.in mm

®Razor-Back Mounting Tube

ASG-RBMT-18 18 450 0ASG-RBMT-24 24 600 0ASG-RBMT-30 30 750 0ASG-RBMT-36 36 900 0ASG-RBMT-42 42 1070 0ASG-RBMT-48 48 1200 0ASG-RBMT-54 54 1350 0ASG-RBMT-60 60 1500 0ASG-RBMT-72 72 1800 0ASG-RBMT-84 84 2100 0ASG-RBMT-96 96 2400 0

Part NumberBelt Width Wt.

Lbs.in mm

®Razor-Back Blade Holder

ASG-RBBH-18 18 450 0ASG-RBBH-24 24 600 0ASG-RBBH-30 30 750 0ASG-RBBH-36 36 900 0ASG-RBBH-42 42 1070 0ASG-RBBH-48 48 1200 0ASG-RBBH-54 54 1350 0ASG-RBBH-60 60 1500 0ASG-RBBH-72 72 1800 0ASG-RBBH-84 84 2100 0ASG-RBBH-96 96 2400 0

®Razor-Back System

X: AR (F-Tip)

X: TC-C (C-Tip)

X: TC (V-Tip)

X: CER (XC- Ceramic Blade)

X: UB (Urethane Blade)

XX ™: BU (Bolt-Up Tensioner)

XX ™: RSS (Duo-Spring Tensioner)

XX ™: ST (Spring-Shoc Tensioner)

M-RB -SYS-18- 18 450X XXM-RB -SYS-24- 24 600X XXM-RB -SYS-30- 30 750X XXM-RB -SYS-36- 36 900X XXM-RB -SYS-42- 42 1070X XXM-RB -SYS-48- 48 1200X XXM-RB -SYS-54- 54 1350X XXM-RB -SYS-60- 60 1500X XXM-RB -SYS-66- 66 1600X XXM-RB -SYS-72- 72 1800X XXM-RB -SYS-84- 84 2100X XX

BW - Belt Width

Part Number

®Razor-Back Replacement Parts

ASG-BLD-RZ-6-AR F-Tip Blade

ASG-BLD-NW3-6-TC-C C-Tip Blade

ASG-BLD-RZ-6-TC V-Tip Blade

M-ASG-CUS-CER-6 XC-Ceramic

ASG-BLD-RZ-6-U Urethane Blade

ASG-CUS-RZ-6C Blade Cushion

ASG-SPRAYBAR-[BW] Spraybar

Description

®Razor-Back Spray Bar

Part Numberin mm

Belt Width

®© 6/2015 ASGCO “Complete Conveyor Solutions”