Section 3 Schedule 40 PVC Piping Systems

175174

GF Piping Systems

Schedule 40 PVC Piping Systems

Section 3

175

176175

Glossary

FPT = Female Pipe Thread

MPT = Male Pipe Thread

S = Tapered Socket

SPG = Spigot End (same dimension as pipe outside diameter)

* = Non-Returnable / Non-cancellable

^ = 40% Restocking Fee

BUSH = Assembled Fitting from Molded Components

FAB = Fabricated Fitting

The technical information given in this publication implies no warranty of any kind and is subject to

change without notice. Please consult our Terms and Conditions of Sale.

For complete technical information, please consult the Vinyl Catalog and Technical Information

For more information about any of our product lines, please visit www.gfps.com

176

177175

Glossary



S = Tapered Socket










177

Table of contents Page

Harvel® Industrial Schedule 40 PVC Pressure Pipe - White 179

Harvel® Industrial PLUS Schedule 40 PVC Pressure Pipe - White 180

Harvel®Schedule 40 PVC Pressure Pipe - Gray 181

Schedule 40 PVC Pressure Fittings 182

177

178178

Specifications and Standards

Specifications and StandardsNSF/ANSI Standard 14

NSF/ANSI Standard 61

ASTM D 1784 : Material PVC Type I, Grade I White or Gray (cell classification 12454)

ASTM D 1785 : PVC Schedule 40 Pipe

ASTM D 2665 : PVC Schedule 40 Drain, Waste, and Vent (DWV)

ASTM D 2466 : PVC Schedule 40 Socket and Threaded Fittings

ASTM F 1498 : PVC Schedule 40 Taper Threads

ASTM D 2672 : PVC Schedule 40 Tapered Sockets for Bell End Pipe

ANSI B1.20.1 : PVC Schedule 40 NPT Threads

P0800892

178

179178

Specifications and Standards



ASTM D 1784 : Material PVC Type I, Grade I White or Gray (cell classification 12454)


ASTM D 2665 : PVC Schedule 40 Drain, Waste, and Vent (DWV)

ASTM D 2466 : PVC Schedule 40 Socket and Threaded Fittings




P0800892

179

Harvel® Industrial Schedule 40 PVC Pressure Pipe - White

Plain End Pipe - 20 ft lengths

• Refer to Industrial PLUS for sizes 3-1/2", 5", 14"-24"• Max Water Pressure at 73°F (22.7°C) with solvent-cemented joints• Meets NSF®-pw-G• Non - CSA Approved Size(inch)

P/L Plain EndPart No.

Lift Qty( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

Max WaterPressure

(psi)1∕2 H17 H0400050PW2000 5700 0.840 0.109 0.161 6003∕4 H17 H0400075PW2000 5260 1.050 0.113 0.214 4801 H17 H0400100PW2000 4280 1.315 0.133 0.315 450

1 1∕4 H17 H0400125PW2000 2360 1.660 0.140 0.426 3701 1∕2 H17 H0400150PW2000 2060 1.900 0.145 0.509 330

2 H17 H0400200PW2000 1660 2.375 0.154 0.682 2802 1∕2 H17 H0400250PW2000 1080 2.875 0.203 1.076 300

3 H17 H0400300PW2000 840 3.500 0.216 1.409 2604 H17 H0400400PW2000 520 4.500 0.237 2.006 2206 H17 H0400600PW2000 340 6.625 0.280 3.535 1808 H17 H0400800PW2000 220 8.625 0.322 5.305 160

10 H17 H0401000PW2000 80 10.750 10.750 7.532 14012 H17 H0401200PW2000 60 12.750 12.750 9.949 130

Belled End Pipe - 20 ft length Less Bell

Size(inch)

P/L Belled EndPart No.

A-Socket Entrance(Belled Pipe)

B-Socket Bottom(Belled Pipe)

C-Min. (BelledPipe)

1∕2 H17 H0400050PW200B 0.848±0.004 0.836±0.004 1.0003∕4 H17 H0400075PW200B 1.058±0.004 1.046±0.004 1.2501 H17 H0400100PW200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H17 H0400125PW200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H17 H0400150PW200B 1.912±0.006 1.894±0.006 2.000

2 H17 H0400200PW200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H17 H0400250PW200B 2.889±0.007 2.861±0.007 2.500

3 H17 H0400300PW200B 3.516±0.008 3.484±0.008 3.2504 H17 H0400400PW200B 4.518±0.009 4.482±0.009 4.0006 H17 H0400600PW200B 6.647±0.011 6.603±0.011 6.0008 H17 H0400800PW200B 8.655±0.015 8.598±0.015 6.000

10 H17 H0401000PW200B 10.776±0.015 10.722±0.015 7.50012 H17 H0401200PW200B 12.778±0.015 12.721±0.015 8.500

179

180180

Harvel® Industrial PLUS Schedule 40 PVC Pressure Pipe - White


• Max Water Pressure at 73°F (22.7°C) with solvent-cemented joints• Meets NSF®-pw-G• Meets CAN/CSA B137.3 Requirements Size(inch)


Lift Qty( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

Max WaterPressure

(psi)1∕2 H51 HX400050PW2000 5700 0.840 0.109 0.161 6003∕4 H51 HX400075PW2000 5260 1.050 0.113 0.214 4801 H51 HX400100PW2000 4280 1.315 0.133 0.315 450

1 1∕4 H51 HX400125PW2000 2360 1.660 0.140 0.426 3701 1∕2 H51 HX400150PW2000 2060 1.900 0.145 0.509 330

2 H51 HX400200PW2000 1660 2.375 0.154 0.682 2802 1∕2 H51 HX400250PW2000 1080 2.875 0.203 1.076 300

3 H51 HX400300PW2000 840 3.500 0.216 1.409 2603 1∕2 H51 H0400350PW2000 680 4.000 0.226 1.697 240

4 H51 HX400400PW2000 520 4.500 0.237 2.006 2205 H51 H0400500PW2000 400 5.563 0.258 2.726 1906 H51 HX400600PW2000 340 6.625 0.280 3.535 1808 H51 HX400800PW2000 220 8.625 0.322 5.305 160

10 H51 HX401000PW2000 80 10.750 0.365 7.532 14012 H51 HX401200PW2000 60 12.750 0.406 9.949 13014 H51 H0401400PW2000 60 14.000 0.437 11.810 13016 H51 H0401600PW2000 60 16.000 0.500 15.416 13018 H51 H0401800PW2000 60 18.000 0.562 20.112 13020 H51 H0402000PW2000 40 20.000 0.593 23.624 12024 H51 H0402400PW2000 40 24.000 0.687 32.873 120


Size(inch)




C-Min. (BelledPipe)

1∕2 H51 HX400050PW200B 0.848±0.004 0.836±0.004 1.0003∕4 H51 HX400075PW200B 1.058±0.004 1.046±0.004 1.2501 H51 HX400100PW200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H51 HX400125PW200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H51 HX400150PW200B 1.912±0.006 1.894±0.006 2.000

2 H51 HX400200PW200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H51 HX400250PW200B 2.889±0.007 2.861±0.007 2.500

3 H51 HX400300PW200B 3.516±0.008 3.484±0.008 3.2503 1∕2 H51 H0400350PW200B 4.016±0.008 3.984±0.008 3.500

4 H51 HX400400PW200B 4.518±0.009 4.482±0.009 4.0005 H51 H0400500PW200B 5.583±0.010 5.543±0.010 4.0006 H51 HX400600PW200B 6.647±0.011 6.603±0.011 6.0008 H51 HX400800PW200B 8.655±0.015 8.598±0.015 6.000

10 H51 HX401000PW200B 10.776±0.015 10.722±0.015 7.50012 H51 HX401200PW200B 12.778±0.015 12.721±0.015 8.50014 H51 H0401400PW200B 14.035±0.015 13.985±0.015 9.00016 H51 H0401600PW200B 16.045±0.015 15.980±0.015 10.00018 H51 H0401800PW200B 18.055±0.020 17.980±0.020 12.00020 H51 H0402000PW200B 20.065±0.025 19.980±0.025 12.00024 H51 H0402400PW200B 24.075±0.030 23.970±0.030 12.000

180

181180

Harvel® Industrial PLUS Schedule 40 PVC Pressure Pipe - White


• Max Water Pressure at 73°F (22.7°C) with solvent-cemented joints• Meets NSF®-pw-G• Meets CAN/CSA B137.3 Requirements Size(inch)


Lift Qty( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

Max WaterPressure

(psi)1∕2 H51 HX400050PW2000 5700 0.840 0.109 0.161 6003∕4 H51 HX400075PW2000 5260 1.050 0.113 0.214 4801 H51 HX400100PW2000 4280 1.315 0.133 0.315 450

1 1∕4 H51 HX400125PW2000 2360 1.660 0.140 0.426 3701 1∕2 H51 HX400150PW2000 2060 1.900 0.145 0.509 330

2 H51 HX400200PW2000 1660 2.375 0.154 0.682 2802 1∕2 H51 HX400250PW2000 1080 2.875 0.203 1.076 300

3 H51 HX400300PW2000 840 3.500 0.216 1.409 2603 1∕2 H51 H0400350PW2000 680 4.000 0.226 1.697 240

4 H51 HX400400PW2000 520 4.500 0.237 2.006 2205 H51 H0400500PW2000 400 5.563 0.258 2.726 1906 H51 HX400600PW2000 340 6.625 0.280 3.535 1808 H51 HX400800PW2000 220 8.625 0.322 5.305 160

10 H51 HX401000PW2000 80 10.750 0.365 7.532 14012 H51 HX401200PW2000 60 12.750 0.406 9.949 13014 H51 H0401400PW2000 60 14.000 0.437 11.810 13016 H51 H0401600PW2000 60 16.000 0.500 15.416 13018 H51 H0401800PW2000 60 18.000 0.562 20.112 13020 H51 H0402000PW2000 40 20.000 0.593 23.624 12024 H51 H0402400PW2000 40 24.000 0.687 32.873 120


Size(inch)




C-Min. (BelledPipe)

1∕2 H51 HX400050PW200B 0.848±0.004 0.836±0.004 1.0003∕4 H51 HX400075PW200B 1.058±0.004 1.046±0.004 1.2501 H51 HX400100PW200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H51 HX400125PW200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H51 HX400150PW200B 1.912±0.006 1.894±0.006 2.000

2 H51 HX400200PW200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H51 HX400250PW200B 2.889±0.007 2.861±0.007 2.500

3 H51 HX400300PW200B 3.516±0.008 3.484±0.008 3.2503 1∕2 H51 H0400350PW200B 4.016±0.008 3.984±0.008 3.500

4 H51 HX400400PW200B 4.518±0.009 4.482±0.009 4.0005 H51 H0400500PW200B 5.583±0.010 5.543±0.010 4.0006 H51 HX400600PW200B 6.647±0.011 6.603±0.011 6.0008 H51 HX400800PW200B 8.655±0.015 8.598±0.015 6.000

10 H51 HX401000PW200B 10.776±0.015 10.722±0.015 7.50012 H51 HX401200PW200B 12.778±0.015 12.721±0.015 8.50014 H51 H0401400PW200B 14.035±0.015 13.985±0.015 9.00016 H51 H0401600PW200B 16.045±0.015 15.980±0.015 10.00018 H51 H0401800PW200B 18.055±0.020 17.980±0.020 12.00020 H51 H0402000PW200B 20.065±0.025 19.980±0.025 12.00024 H51 H0402400PW200B 24.075±0.030 23.970±0.030 12.000

181

Harvel® Schedule 40 PVC Pressure Pipe - Gray


• Max Water Pressure at 73°F (22.7°C) with solvent-cemented joints• Meets NSF®-pw-G• Non - CSA Approved Size(inch)


Lift Qty( ft)

Average O.D.(inch)

min. wall(inch)

Wt/Ft(lbs ⁄ ft)

Max WaterPressure

(psi)1∕8 H16 H0400013PG2000 5700 0.405 0.068 0.045 8101∕4 H16 H0400025PG2000 5700 0.540 0.088 0.081 7803∕8 H16 H0400038PG2000 5700 0.675 0.091 0.109 6201∕2 H16 H0400050PG2000 5700 0.840 0.109 0.161 6003∕4 H16 H0400075PG2000 5260 1.050 0.113 0.214 4801 H16 H0400100PG2000 4280 1.315 0.133 0.315 450

1 1∕4 H16 H0400125PG2000 2360 1.660 0.140 0.426 3701 1∕2 H16 H0400150PG2000 2060 1.900 0.145 0.509 330

2 H16 H0400200PG2000 1660 2.375 0.154 0.682 2802 1∕2 H16 H0400250PG2000 1080 2.875 0.203 1.076 300

3 H16 H0400300PG2000 840 3.500 0.216 1.409 2603 1∕2 H16 H0400350PG2000 680 4.000 0.226 1.697 240

4 H16 H0400400PG2000 520 4.500 0.237 2.006 2205 H16 H0400500PG2000 400 5.563 0.258 2.726 1906 H16 H0400600PG2000 340 6.625 0.280 3.535 1808 H16 H0400800PG2000 220 8.625 0.332 5.305 160

10 H16 H0401000PG2000 80 10.750 0.365 7.532 14012 H16 H0401200PG2000 60 12.750 0.406 9.949 13014 H16 H0401400PG2000 60 14.000 0.437 11.810 13016 H16 H0401600PG2000 60 16.000 0.500 15.416 13018 H16 H0401800PG2000 40 18.000 0.562 20.112 13020 H16 H0402000PG2000 40 20.000 0.593 23.624 12024 H16 H0402400PG2000 40 24.000 0.687 32.873 120


Size(inch)


A-Socket En-trance (Belled

Pipe)

B-Socket Bot-tom (Belled

Pipe)

C-Min. (BelledPipe)

1∕2 H16 H0400050PG200B 0.848±0.004 0.836±0.004 1.0003∕4 H16 H0400075PG200B 1.058±0.004 1.046±0.004 1.2501 H16 H0400100PG200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H16 H0400125PG200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H16 H0400150PG200B 1.912±0.005 1.894±0.006 2.000

2 H16 H0400200PG200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H16 H0400250PG200B 2.889±0.007 2.861±0.007 2.500

3 H16 H0400300PG200B 3.516±0.008 3.484±0.008 3.2503 1∕2 H16 H0400350PG200B 4.016±0.008 3.984±0.008 3.500

4 H16 H0400400PG200B 4.518±0.009 4.482±0.009 4.0005 H16 H0400500PG200B 5.583±0.010 5.543±0.010 4.0006 H16 H0400600PG200B 6.647±0.011 6.603±0.011 6.0008 H16 H0400800PG200B 8.655±0.015 8.598±0.015 6.000

10 H16 H0401000PG200B 10.776±0.015 10.722±0.015 7.50012 H16 H0401200PG200B 12.778±0.015 12.721±0.015 8.50014 H16 H0401400PG200B 14.035±0.015 13.985±0.015 9.00016 H16 H0401600PG200B 16.045±0.015 15.980±0.015 10.00018 H16 H0401800PG200B 18.055±0.020 17.980±0.020 12.00020 H16 H0402000PG200B 20.065±0.025 19.980±0.025 12.00024 H16 H0402400PG200B 24.075±0.030 23.970±0.030 12.000

181

182

table continued on the next page182

Schedule 40 PVC Pressure Fittings

Tee (S x S x S)

Size(inch)

P/L Part No. PackQty

H(inch)

G(inch)

Design

1∕2 601 401-005 50 1.25 0.383∕4 601 401-007 50 1.38 0.561 601 401-010 50 1.69 0.69

1 1∕4 601 401-012 25 2.13 0.881 1∕2 601 401-015 25 2.31 1.00

2 601 401-020 25 2.63 1.252 1∕2 601 401-025 10 3.50 1.50

3 601 401-030 10 3.81 1.814 601 401-040 5 4.31 2.316 601 401-060 4 7.06 3.508 601 401-080 2 9.00 4.50

10 B09 401-100 1 10.94 5.8812 B09 401-120 1 13.06 7.0014 A32 401-140N 1 19.38 10.06 FAB16 A32 401-160N 1 21.63 11.75 FAB18 A32 401-180N 1 24.50 12.88 FAB20 A32 401-200N 1 26.25 14.31 FAB24 A32 401-240N 1 33.13 16.75 FAB

Reducing Tee (S x S x S)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

3∕4 x 1∕2 x 1∕2 601 401-094 50 1.31 1.31 0.50 0.563∕4 x 1∕2 x 3∕4 601 401-095 50 1.31 1.31 0.56 0.563∕4 x 3∕4 x 1∕2 601 401-101 50 1.31 1.38 0.50 0.633∕4 x 3∕4 x 1 601 401-102 50 1.50 1.56 0.69 0.561 x 1∕2 x 1 601 401-122 50 1.69 1.69 0.69 0.751 x 3∕4 x 3∕4 601 401-125 50 1.56 1.44 0.53 0.691 x 3∕4 x 1 601 401-126 50 1.69 1.69 0.75 0.691 x 1 x 1∕2 601 401-130 50 1.50 1.50 0.50 0.691 x 1 x 3∕4 601 401-131 50 1.56 1.50 0.56 0.69

1 x 1 x 1 1∕4 601 401-132 50 1.88 1.94 0.88 0.691 x 1 x 1 1∕2 601 401-133 25 2.00 2.00 1.00 0.691 1∕4 x 1 x 3∕4 601 401-157 25 2.06 1.63 0.88 0.881 1∕4 x 1 x 1 601 401-158 25 2.06 2.00 0.88 0.88

1 1∕4 x 1 1∕4 x 1∕2 601 401-166 25 1.75 1.63 1.25 0.881 1∕4 x 1 1∕4 x 3∕4 601 401-167 25 1.88 1.69 0.56 0.881 1∕4 x 1 1∕4 x 1 601 401-168 25 1.94 1.88 0.69 0.881 1∕2 x 1 1∕2 x 1∕2 601 401-209 25 1.81 1.81 0.50 1.001 1∕2 x 1 1∕2 x 3∕4 601 401-210 25 1.94 1.81 0.63 1.001 1∕2 x 1 1∕2 x 1 601 401-211 25 2.00 2.00 0.69 1.00

1 1∕2 x 1 1∕2 x 1 1∕4 601 401-212 25 2.19 2.25 0.88 1.062 x 1 1∕2 x 3∕4 601 401-238 10 2.00 2.06 0.56 1.252 x 1 1∕2 x 1 601 401-239 10 2.63 2.25 1.25 1.19

2 x 2 x 1∕2 601 401-247 10 1.88 2.00 0.50 1.252 x 2 x 3∕4 601 401-248 10 2.00 2.00 0.56 1.252 x 2 x 1 601 401-249 10 2.06 2.25 0.69 1.25

2 x 2 x 1 1∕4 601 401-250 10 2.25 2.50 0.88 1.252 x 2 x 1 1∕2 601 401-251 10 2.38 2.56 1.00 1.25

2 1∕2 x 2 1∕2 x 3∕4 601 401-288 10 2.44 2.31 0.56 1.50

182

183



Tee (S x S x S)

Size(inch)


H(inch)

G(inch)

Design

1∕2 601 401-005 50 1.25 0.383∕4 601 401-007 50 1.38 0.561 601 401-010 50 1.69 0.69

1 1∕4 601 401-012 25 2.13 0.881 1∕2 601 401-015 25 2.31 1.00

2 601 401-020 25 2.63 1.252 1∕2 601 401-025 10 3.50 1.50

3 601 401-030 10 3.81 1.814 601 401-040 5 4.31 2.316 601 401-060 4 7.06 3.508 601 401-080 2 9.00 4.50


Reducing Tee (S x S x S)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

3∕4 x 1∕2 x 1∕2 601 401-094 50 1.31 1.31 0.50 0.563∕4 x 1∕2 x 3∕4 601 401-095 50 1.31 1.31 0.56 0.563∕4 x 3∕4 x 1∕2 601 401-101 50 1.31 1.38 0.50 0.633∕4 x 3∕4 x 1 601 401-102 50 1.50 1.56 0.69 0.561 x 1∕2 x 1 601 401-122 50 1.69 1.69 0.69 0.751 x 3∕4 x 3∕4 601 401-125 50 1.56 1.44 0.53 0.691 x 3∕4 x 1 601 401-126 50 1.69 1.69 0.75 0.691 x 1 x 1∕2 601 401-130 50 1.50 1.50 0.50 0.691 x 1 x 3∕4 601 401-131 50 1.56 1.50 0.56 0.69

1 x 1 x 1 1∕4 601 401-132 50 1.88 1.94 0.88 0.691 x 1 x 1 1∕2 601 401-133 25 2.00 2.00 1.00 0.691 1∕4 x 1 x 3∕4 601 401-157 25 2.06 1.63 0.88 0.881 1∕4 x 1 x 1 601 401-158 25 2.06 2.00 0.88 0.88

1 1∕4 x 1 1∕4 x 1∕2 601 401-166 25 1.75 1.63 1.25 0.881 1∕4 x 1 1∕4 x 3∕4 601 401-167 25 1.88 1.69 0.56 0.881 1∕4 x 1 1∕4 x 1 601 401-168 25 1.94 1.88 0.69 0.881 1∕2 x 1 1∕2 x 1∕2 601 401-209 25 1.81 1.81 0.50 1.001 1∕2 x 1 1∕2 x 3∕4 601 401-210 25 1.94 1.81 0.63 1.001 1∕2 x 1 1∕2 x 1 601 401-211 25 2.00 2.00 0.69 1.00

1 1∕2 x 1 1∕2 x 1 1∕4 601 401-212 25 2.19 2.25 0.88 1.062 x 1 1∕2 x 3∕4 601 401-238 10 2.00 2.06 0.56 1.252 x 1 1∕2 x 1 601 401-239 10 2.63 2.25 1.25 1.19

2 x 2 x 1∕2 601 401-247 10 1.88 2.00 0.50 1.252 x 2 x 3∕4 601 401-248 10 2.00 2.00 0.56 1.252 x 2 x 1 601 401-249 10 2.06 2.25 0.69 1.25

2 x 2 x 1 1∕4 601 401-250 10 2.25 2.50 0.88 1.252 x 2 x 1 1∕2 601 401-251 10 2.38 2.56 1.00 1.25

2 1∕2 x 2 1∕2 x 3∕4 601 401-288 10 2.44 2.31 0.56 1.50

183

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

2 1∕2 x 2 1∕2 x 1 601 401-289 10 2.56 2.63 0.69 1.502 1∕2 x 2 1∕2 x 1 1∕4 601 401-290 10 2.88 2.75 0.88 1.502 1∕2 x 2 1∕2 x 1 1∕2 601 401-291 10 3.13 2.75 1.00 1.50

2 1∕2 x 2 1∕2 x 2 601 401-292 10 3.13 2.88 1.25 1.503 x 3 x 3∕4 601 401-334 10 2.56 2.56 0.56 1.813 x 3 x 1 601 401-335 10 2.69 2.88 0.69 1.81

3 x 3 x 1 1∕4 601 401-336 10 2.88 3.06 0.88 1.813 x 3 x 1 1∕2 601 401-337 10 3.00 3.19 1.00 1.81

3 x 3 x 2 601 401-338 10 3.25 3.19 1.25 1.814 x 4 x 3∕4 601 401-416 4 2.56 3.00 0.56 2.314 x 4 x 1 601 401-417 4 2.75 3.31 0.69 2.31

4 x 4 x 1 1∕4 601 401-418 5 2.88 3.56 0.88 2.314 x 4 x 2 601 401-420 5 3.25 3.69 1.25 2.31

4 x 4 x 1 1∕2 601 401-419 5 3.00 3.63 1.00 2.314 x 4 x 3 601 401-422 5 3.81 4.38 1.81 2.316 x 6 x 2 601 401-528 5 4.75 4.94 1.25 3.506 x 6 x 3 601 401-530 5 5.38 5.56 1.81 3.566 x 6 x 4 601 401-532 5 5.88 5.56 2.38 3.508 x 8 x 4 601 401-582 2 6.81 6.94 2.31 4.888 x 8 x 6 601 401-585 2 8.00 8.06 3.50 4.50

10 x 10 x 4 B09 401-624 1 10.50 7.94 5.44 5.9410 x 10 x 6 B09 401-626 1 10.50 8.94 5.44 5.9410 x 10 x 8 B09 401-628 1 10.50 9.88 5.44 5.8812 x 12 x 4 B09 401-664 1 11.50 9.00 5.44 6.9412 x 12 x 6 B09 401-666 1 11.50 10.00 5.44 6.9412 x 12 x 8 B09 401-668 1 11.50 11.00 5.44 7.00

12 x 12 x 10 B09 401-670 1 13.06 13.50 7.00 8.4414 x 14 x 4 A32 401-696N 1 12.18 12.00 5.18 10.00 FAB14 x 14 x 6 A32 401-698N 1 13.12 13.63 6.12 10.63 FAB14 x 14 x 8 A32 401-700N 1 14.25 15.25 7.25 11.75 FAB

14 x 14 x 10 A32 401-702N 1 15.31 16.75 8.31 11.75 FAB14 x 14 x 12 A32 401-704N 1 16.00 18.00 9.00 12.00 FAB

16 x 16 x 4 A32 401-730N 1 14.00 13.38 6.00 11.38 FAB16 x 16 x 6 A32 401-732N 1 15.00 14.50 7.00 11.50 FAB16 x 16 x 8 A32 401-734N 1 16.00 16.25 8.00 12.25 FAB

16 x 16 x 10 A32 401-736N 1 16.50 17.75 8.50 12.75 FAB16 x 16 x 12 A32 401-738N 1 19.25 19.50 9.63 13.50 FAB16 x 16 x 14 A32 401-740N 1 19.18 20.50 11.18 13.50 FAB

18 x 18 x 6 A32 401-786N 1 15.63 15.75 6.63 12.75 FAB18 x 18 x 8 A32 401-788N 1 16.63 17.00 7.63 13.00 FAB

18 x 18 x 10 A32 401-790N 1 17.75 18.38 8.75 13.38 FAB18 x 18 x 12 A32 401-792N 1 18.75 20.50 9.75 14.50 FAB18 x 18 x 14 A32 401-794N 1 19.56 21.38 10.56 14.38 FAB18 x 18 x 16 A32 401-796N 1 20.63 22.50 11.63 14.50 FAB

20 x 20 x 8 A32 401-818N 1 18.94 18.13 8.94 14.13 FAB20 x 20 x 10 A32 401-820N 1 19.69 19.75 9.69 14.75 FAB20 x 20 x 12 A32 401-822N 1 21.00 21.13 11.00 15.13 FAB20 x 20 x 14 A32 401-824N 1 21.63 22.75 11.63 15.75 FAB20 x 20 x 16 A32 401-826N 1 23.00 24.50 13.00 16.50 FAB20 x 20 x 18 A32 401-828N 1 23.81 24.50 13.81 15.50 FAB

24 x 24 x 6 A32 401-906N 1 27.75 18.50 7.88 15.50 FAB24 x 24 x 8 A32 401-908N 1 20.69 20.50 8.69 16.50 FAB

24 x 24 x 10 A32 401-910N 1 21.88 21.63 9.88 16.63 FAB24 x 24 x 12 A32 401-912N 1 23.00 23.00 11.00 17.00 FAB24 x 24 x 14 A32 401-914N 1 23.88 25.00 11.88 18.00 FAB24 x 24 x 16 A32 401-916N 1 24.94 26.31 12.94 18.31 FAB24 x 24 x 18 A32 401-918N 1 25.88 27.75 13.88 18.75 FAB24 x 24 x 20 A32 401-920N 1 26.94 30.00 14.94 20.00 FAB

183

184184

Tee (S x S X FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 402-005 50 1.25 1.25 0.50 0.753∕4 601 402-007 50 1.38 1.38 0.56 0.811 601 402-010 50 1.69 1.69 0.69 1.00

1 1∕4 601 402-012 25 2.13 2.13 0.88 0.941 1∕2 601 402-015 25 2.31 2.31 1.00 0.88

2 601 402-020 10 2.63 2.19 1.25 0.943 601 402-030 10 3.81 3.19 1.81 1.444 601 402-040 5 4.31 4.00 2.31 1.69

Reducing Tee (S x S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

3∕4 x 3∕4 x 1∕2 601 402-101 50 1.31 1.31 0.50 0.751 x 1 x 1∕2 601 402-130 50 1.50 1.43 0.50 0.691 x 1 x 3∕4 601 402-131 50 1.56 1.50 0.56 0.75

1 1∕4 x 1 1∕4 x 3∕4 601 402-167 25 1.81 1.63 0.56 0.691 1∕4 x 1 1∕4 x 1 601 402-168 25 1.94 1.88 0.69 0.881 1∕2 x 1 1∕2 x 1∕2 601 402-209 25 1.81 1.75 0.50 0.751 1∕2 x 1 1∕2 x 3∕4 601 402-210 25 1.88 1.81 0.56 0.691 1∕2 x 1 1∕2 x 1 601 402-211 25 2.00 2.00 0.69 1.00

1 1∕2 x 1 1∕2 x 1 1∕4 601 402-212 25 2.19 2.25 0.88 1.252 x 2 x 1∕2 601 402-247 10 1.88 2.00 0.50 0.752 x 2 x 3∕4 601 402-248 10 2.00 2.06 0.56 0.812 x 2 x 1 601 402-249 10 2.06 2.25 0.69 1.00

2 x 2 x 1 1∕4 601 402-250 10 2.25 2.50 0.88 0.942 x 2 x 1 1∕2 601 402-251 10 2.38 2.56 1.00 0.94

2 1∕2 x 2 1∕2 x 1 1∕2 601 402-291 10 3.00 2.50 1.00 1.002 1∕2 x 2 1∕2 x 2 601 402-292 10 3.25 2.88 1.25 1.06

3 x 3 x 1 1∕2 601 402-337 10 6.00 2.81 1.00 0.943 x 3 x 2 601 402-338 10 6.56 2.88 1.25 1.06

4 x 4 x 1 1∕2 601 402-419 5 6.06 3.69 1.00 1.384 x 4 x 2 601 402-420 5 6.50 3.38 1.25 1.134 x 4 x 3 601 402-422 5 7.63 4.63 1.81 1.636 x 6 x 3 601 402-530 5 10.69 5.50 2.31 2.006 x 6 x 4 601 402-532 5 11.69 5.50 2.31 2.00

184

185184

Tee (S x S X FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 402-005 50 1.25 1.25 0.50 0.753∕4 601 402-007 50 1.38 1.38 0.56 0.811 601 402-010 50 1.69 1.69 0.69 1.00

1 1∕4 601 402-012 25 2.13 2.13 0.88 0.941 1∕2 601 402-015 25 2.31 2.31 1.00 0.88

2 601 402-020 10 2.63 2.19 1.25 0.943 601 402-030 10 3.81 3.19 1.81 1.444 601 402-040 5 4.31 4.00 2.31 1.69

Reducing Tee (S x S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

3∕4 x 3∕4 x 1∕2 601 402-101 50 1.31 1.31 0.50 0.751 x 1 x 1∕2 601 402-130 50 1.50 1.43 0.50 0.691 x 1 x 3∕4 601 402-131 50 1.56 1.50 0.56 0.75

1 1∕4 x 1 1∕4 x 3∕4 601 402-167 25 1.81 1.63 0.56 0.691 1∕4 x 1 1∕4 x 1 601 402-168 25 1.94 1.88 0.69 0.881 1∕2 x 1 1∕2 x 1∕2 601 402-209 25 1.81 1.75 0.50 0.751 1∕2 x 1 1∕2 x 3∕4 601 402-210 25 1.88 1.81 0.56 0.691 1∕2 x 1 1∕2 x 1 601 402-211 25 2.00 2.00 0.69 1.00

1 1∕2 x 1 1∕2 x 1 1∕4 601 402-212 25 2.19 2.25 0.88 1.252 x 2 x 1∕2 601 402-247 10 1.88 2.00 0.50 0.752 x 2 x 3∕4 601 402-248 10 2.00 2.06 0.56 0.812 x 2 x 1 601 402-249 10 2.06 2.25 0.69 1.00

2 x 2 x 1 1∕4 601 402-250 10 2.25 2.50 0.88 0.942 x 2 x 1 1∕2 601 402-251 10 2.38 2.56 1.00 0.94

2 1∕2 x 2 1∕2 x 1 1∕2 601 402-291 10 3.00 2.50 1.00 1.002 1∕2 x 2 1∕2 x 2 601 402-292 10 3.25 2.88 1.25 1.06

3 x 3 x 1 1∕2 601 402-337 10 6.00 2.81 1.00 0.943 x 3 x 2 601 402-338 10 6.56 2.88 1.25 1.06

4 x 4 x 1 1∕2 601 402-419 5 6.06 3.69 1.00 1.384 x 4 x 2 601 402-420 5 6.50 3.38 1.25 1.134 x 4 x 3 601 402-422 5 7.63 4.63 1.81 1.636 x 6 x 3 601 402-530 5 10.69 5.50 2.31 2.006 x 6 x 4 601 402-532 5 11.69 5.50 2.31 2.00

185

Tee (FPT x FPT x FPT)

Size(inch)


H(inch)

T(inch)

1∕2 601 405-005 50 1.25 0.723∕4 601 405-007 50 1.38 0.811 601 405-010 50 1.69 1.00

1 1∕4 601 405-012 25 2.13 0.881 1∕2 601 405-015 25 2.31 1.31

90° Ell (S x S)

Size(inch)


H(inch)

G(inch)

Design

1∕2 601 406-005 50 1.25 0.503∕4 601 406-007 50 1.38 0.561 601 406-010 50 1.69 0.69

1 1∕4 601 406-012 25 2.13 0.881 1∕2 601 406-015 25 2.25 1.00

2 601 406-020 25 2.56 1.252 1∕2 601 406-025 10 3.50 1.50

3 601 406-030 10 3.81 1.814 601 406-040 5 4.38 2.316 601 406-060 4 7.00 3.508 601 406-080 3 9.00 4.50


185

186186

Reducing 90° Ell (S x S)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

3∕4 x 1∕2 601 406-101 50 1.31 1.31 0.50 0.561 x 1∕2 601 406-130 50 1.50 1.38 0.50 0.691 x 3∕4 601 406-131 50 1.56 1.50 0.56 0.69

90° Ell (S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 407-005 50 1.25 1.19 0.50 0.753∕4 601 407-007 50 1.38 1.38 0.63 0.811 601 407-010 50 1.63 1.69 0.69 1.00

1 1∕4 601 407-012 25 2.19 1.81 0.88 0.881 1∕2 601 407-015 25 2.31 2.31 1.00 1.31

2 601 407-020 10 2.63 2.63 1.25 1.382 1∕2 601 407-025 10 3.38 2.75 1.50 1.25

3 601 407-030 10 3.75 3.19 1.75 1.564 601 407-040 5 4.38 4.19 2.38 0.88

Reducing 90° Ell (S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

3∕4 x 1∕2 601 407-101 50 1.38 1.25 0.56 0.681 x 1∕2 601 407-130 50 1.56 1.38 0.56 0.691 x 3∕4 601 407-131 50 1.56 1.50 0.56 0.81

1 1∕4 x 1 601 407-168 25 1.94 1.88 0.69 1.001 1∕2 x 1 601 407-211 25 1.94 2.75 1.06 1.00

1 1∕2 x 1 1∕4 601 407-212 25 2.19 2.25 0.88 0.942 x 1 601 407-249 25 2.19 2.44 0.81 0.88

2 x 1 1∕4 601 407-250 10 2.25 2.44 0.88 0.882 x 1 1∕2 601 407-251 10 2.44 2.63 1.06 0.94

186

187186

Reducing 90° Ell (S x S)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

3∕4 x 1∕2 601 406-101 50 1.31 1.31 0.50 0.561 x 1∕2 601 406-130 50 1.50 1.38 0.50 0.691 x 3∕4 601 406-131 50 1.56 1.50 0.56 0.69

90° Ell (S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 407-005 50 1.25 1.19 0.50 0.753∕4 601 407-007 50 1.38 1.38 0.63 0.811 601 407-010 50 1.63 1.69 0.69 1.00

1 1∕4 601 407-012 25 2.19 1.81 0.88 0.881 1∕2 601 407-015 25 2.31 2.31 1.00 1.31

2 601 407-020 10 2.63 2.63 1.25 1.382 1∕2 601 407-025 10 3.38 2.75 1.50 1.25

3 601 407-030 10 3.75 3.19 1.75 1.564 601 407-040 5 4.38 4.19 2.38 0.88

Reducing 90° Ell (S x FPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

3∕4 x 1∕2 601 407-101 50 1.38 1.25 0.56 0.681 x 1∕2 601 407-130 50 1.56 1.38 0.56 0.691 x 3∕4 601 407-131 50 1.56 1.50 0.56 0.81

1 1∕4 x 1 601 407-168 25 1.94 1.88 0.69 1.001 1∕2 x 1 601 407-211 25 1.94 2.75 1.06 1.00

1 1∕2 x 1 1∕4 601 407-212 25 2.19 2.25 0.88 0.942 x 1 601 407-249 25 2.19 2.44 0.81 0.88

2 x 1 1∕4 601 407-250 10 2.25 2.44 0.88 0.882 x 1 1∕2 601 407-251 10 2.44 2.63 1.06 0.94

187

90° Ell (FPT x FPT)

Size(inch)


H(inch)

T(inch)

1∕2 601 408-005 50 1.31 0.813∕4 601 408-007 50 1.38 0.811 601 408-010 50 1.69 1.00

1 1∕4 601 408-012 25 2.13 1.191 1∕2 601 408-015 25 2.31 1.38

2 601 408-020 10 2.63 1.38

90° Street Ell (S x SPG)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 409-005 50 1.31 1.13 0.56 0.813∕4 601 409-007 50 1.63 1.25 0.81 0.751 601 409-010 50 1.88 1.44 0.88 0.88

1 1∕4 601 409-012 25 2.38 2.13 1.06 1.311 1∕2 601 409-015 25 2.63 2.31 1.25 1.31

2 601 409-020 10 2.88 2.63 1.44 1.382 1∕2 601 409-025 10 4.06 3.38 2.00 1.94

3 601 409-030 10 4.44 4.19 2.31 2.00

90° Street Ell (S x MPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 410-005 50 1.25 1.31 0.69 0.633∕4 601 410-007 50 1.25 1.56 0.75 0.811 601 410-010 50 1.56 1.88 1.00 0.88

1 1∕4 601 410-012 25 2.06 1.94 1.13 0.811 1∕2 601 410-015 25 2.31 2.31 1.25 1.06

2 601 410-020 10 2.69 2.25 1.50 0.75

187

188188

90° Street Ell (FPT x MPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 412-005 50 1.44 1.06 0.81 0.313∕4 601 412-007 50 1.63 1.19 0.81 0.441 601 412-010 50 1.88 1.44 0.88 0.56

1 1∕4 601 412-012 25 1.94 2.13 1.13 1.191 1∕2 601 412-015 25 2.31 2.31 1.25 1.31

2 601 412-020 10 2.75 2.31 1.56 1.06

Side Outlet Elbow (S x S x S)

Size(inch)


H(inch)

G(inch)

1∕2 601 413-005 50 1.31 0.563∕4 601 413-007 50 1.38 0.561 601 413-010 25 1.69 0.69

1 1∕2 601 413-015 25 2.44 1.002 601 413-020 10 2.63 1.25

188

189188

90° Street Ell (FPT x MPT)

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

1∕2 601 412-005 50 1.44 1.06 0.81 0.313∕4 601 412-007 50 1.63 1.19 0.81 0.441 601 412-010 50 1.88 1.44 0.88 0.56

1 1∕4 601 412-012 25 1.94 2.13 1.13 1.191 1∕2 601 412-015 25 2.31 2.31 1.25 1.31

2 601 412-020 10 2.75 2.31 1.56 1.06

Side Outlet Elbow (S x S x S)

Size(inch)


H(inch)

G(inch)

1∕2 601 413-005 50 1.31 0.563∕4 601 413-007 50 1.38 0.561 601 413-010 25 1.69 0.69

1 1∕2 601 413-015 25 2.44 1.002 601 413-020 10 2.63 1.25

189

45° Ell (S x S)

Size(inch)


H(inch)

J(inch)

Design

1∕2 601 417-005 50 1.06 0.253∕4 601 417-007 50 1.19 0.381 601 417-010 50 1.44 0.31

1 1∕4 601 417-012 25 1.63 0.381 1∕2 601 417-015 25 1.69 0.44

2 601 417-020 25 2.00 0.692 1∕2 601 417-025 10 2.69 0.69

3 601 417-030 10 2.75 0.754 601 417-040 5 3.00 1.006 601 417-060 4 5.38 1.818 601 417-080 4 6.50 2.00


Cross (S x S x S x S)

Size(inch)


L(inch)

H(inch)

G(inch)

1∕2 601 420-005 50 2.44 1.19 0.503∕4 601 420-007 50 2.63 1.31 0.561 601 420-010 50 3.38 1.69 0.69

1 1∕4 601 420-012 25 4.25 2.13 0.881 1∕2 601 420-015 25 4.63 2.31 1.00

2 601 420-020 10 5.25 2.63 1.252 1∕2 601 420-025 8 7.00 3.50 1.50

3 601 420-030 10 7.63 3.81 1.814 601 420-040 5 8.69 4.31 2.31

189

190190

Reducing Cross (S x S x S x S)

Size(inch)


H(inch)

H1(inch)

G(inch)

G1(inch)

3 x 1 1∕2 601 420-337 10 3.00 3.13 1.00 1.813 x 2 601 420-338 10 3.25 3.19 1.25 1.81

4 x 1 1∕2 601 420-419 5 3.00 3.63 1.00 2.314 x 2 601 420-420 5 3.25 3.69 1.25 2.31

Coupling (S x S)

Size(inch)


L(inch)

N(inch)

Design

1∕2 601 429-005 100 1.69 0.133∕4 601 429-007 50 1.69 0.131 601 429-010 50 2.06 0.13

1 1∕4 601 429-012 25 2.63 0.131 1∕2 601 429-015 25 2.75 0.13

2 601 429-020 25 2.88 0.132 1∕2 601 429-025 10 4.06 0.19

3 601 429-030 10 4.19 0.194 601 429-040 5 4.25 0.196 601 429-060 5 7.31 0.318 601 429-080 4 9.25 0.25


190

191190

Reducing Cross (S x S x S x S)

Size(inch)


H(inch)

H1(inch)

G(inch)

G1(inch)

3 x 1 1∕2 601 420-337 10 3.00 3.13 1.00 1.813 x 2 601 420-338 10 3.25 3.19 1.25 1.81

4 x 1 1∕2 601 420-419 5 3.00 3.63 1.00 2.314 x 2 601 420-420 5 3.25 3.69 1.25 2.31

Coupling (S x S)

Size(inch)


L(inch)

N(inch)

Design

1∕2 601 429-005 100 1.69 0.133∕4 601 429-007 50 1.69 0.131 601 429-010 50 2.06 0.13

1 1∕4 601 429-012 25 2.63 0.131 1∕2 601 429-015 25 2.75 0.13

2 601 429-020 25 2.88 0.132 1∕2 601 429-025 10 4.06 0.19

3 601 429-030 10 4.19 0.194 601 429-040 5 4.25 0.196 601 429-060 5 7.31 0.318 601 429-080 4 9.25 0.25


191

Reducing Coupling (S x S)

Size(inch)


L(inch)

N(inch)

Design

3∕4 x 1∕2 601 429-101 50 1.63 0.131 x 3∕4 601 429-131 50 2.13 0.25

1 1∕4 x 1 601 429-168 25 2.56 0.311 1∕2 x 1 1∕4 601 429-212 25 2.75 0.25

2 x 1 1∕2 601 429-251 10 3.13 0.443 x 2 601 429-338 5 4.06 0.634 x 3 601 429-422 4 4.63 0.636 x 4 601 429-532 4 6.63 1.198 x 4 601 429-582 4 8.94 2.388 x 6 601 429-585 4 9.06 1.06

10 x 6 B09 429-626 1 10.81 2.6910 x 8 B09 429-628 1 10.75 1.6912 x 8 B09 429-668 1 12.88 2.69

12 x 10 B09 429-670 1 13.06 1.9414 x 4 A32 429-696N 1 10.50 4.75 FAB14 x 6 A32 429-698N 1 11.50 4.50 FAB14 x 8 A32 429-700N 1 13.25 5.50 FAB

14 x 10 A32 429-702N 1 17.00 5.00 FAB14 x 12 A32 429-704N 1 17.00 4.00 FAB

16 x 4 A32 429-730N 1 10.75 4.50 FAB16 x 6 A32 429-732N 1 11.75 4.50 FAB16 x 8 A32 429-734N 1 12.25 6.00 FAB


18 x 6 A32 429-786N 1 12.75 5.00 FAB18 x 8 A32 429-788N 1 14.00 6.00 FAB

18 x 10 A32 429-790N 1 15.75 6.00 FAB18 x 12 A32 429-792N 1 22.38 7.38 FAB18 x 14 A32 429-794N 1 22.25 6.25 FAB18 x 16 A32 429-796N 1 22.38 5.38 FAB

20 x 8 A32 429-818N 1 14.00 5.75 FAB20 x 10 A32 429-820N 1 34.50 19.25 FAB20 x 12 A32 429-822N 1 34.75 17.00 FAB20 x 14 A32 429-824N 1 33.00 15.75 FAB20 x 16 A32 429-826N 1 23.75 5.75 FAB20 x 18 A32 429-828N 1 23.50 4.50 FAB

24 x 6 A32 429-906N 1 14.50 5.25 FAB24 x 8 A32 429-908N 1 16.00 6.00 FAB


191

192192

Coupling (FPT x FPT)

Size(inch)


L(inch)

T(inch)

1∕2 601 430-005 100 1.56 0.693∕4 601 430-007 50 1.81 0.971 601 430-010 50 1.56 1.002 601 430-020 25 1.75 0.94

Female Adapter (S x FPT)

Size(inch)


L(inch)

N(inch)

1∕2 601 435-005 100 1.75 0.313∕4 601 435-007 50 1.75 0.311 601 435-010 50 2.19 0.13

1 1∕4 601 435-012 25 2.25 0.061 1∕2 601 435-015 25 2.25 0.06

2 601 435-020 25 2.44 0.062 1∕2 601 435-025 10 3.75 0.19

3 601 435-030 10 3.75 0.194 601 435-040 5 4.00 0.196 601 435-060 4 5.75 0.258 601 435-080 4 6.94 0.25

192

193192

Coupling (FPT x FPT)

Size(inch)


L(inch)

T(inch)

1∕2 601 430-005 100 1.56 0.693∕4 601 430-007 50 1.81 0.971 601 430-010 50 1.56 1.002 601 430-020 25 1.75 0.94

Female Adapter (S x FPT)

Size(inch)


L(inch)

N(inch)

1∕2 601 435-005 100 1.75 0.313∕4 601 435-007 50 1.75 0.311 601 435-010 50 2.19 0.13

1 1∕4 601 435-012 25 2.25 0.061 1∕2 601 435-015 25 2.25 0.06

2 601 435-020 25 2.44 0.062 1∕2 601 435-025 10 3.75 0.19

3 601 435-030 10 3.75 0.194 601 435-040 5 4.00 0.196 601 435-060 4 5.75 0.258 601 435-080 4 6.94 0.25

193

Reducing Female Adapter (S x FPT)

Size(inch)


L(inch)

N(inch)

T(inch)

3∕4 x 1∕2 601 435-101 50 1.56 0.13 0.693∕4 x 1 601 435-102 50 1.75 0.06 1.001 x 3∕4 601 435-131 50 1.88 0.00 0.88

1 x 1 1∕2 601 435-211 25 2.19 0.19 1.00

Male Adapter (MPT x S)

Size(inch)


HL(inch)

L(inch)

1∕2 601 436-005 100 0.69 1.563∕4 601 436-007 50 0.25 1.561 601 436-010 50 1.00 2.00

1 1∕4 601 436-012 25 1.25 2.501 1∕2 601 436-015 25 1.19 2.50

2 601 436-020 25 1.31 2.692 1∕2 601 436-025 10 1.88 3.88

3 601 436-030 10 1.94 3.944 601 436-040 5 2.06 4.066 601 436-060 4 2.38 5.888 601 436-080 4 2.56 7.13

12 A32 436-120N 1 5.00 10.50

Reducing Male Adapter (MPT x S)

Size(inch)


HL(inch)

L(inch)

1∕2 x 3∕4 601 436-074 50 0.88 1.753∕4 x 1∕2 601 436-101 50 0.94 1.693∕4 x 1 601 436-102 50 0.81 1.811 x 3∕4 601 436-131 50 1.00 2.31

1 x 1 1∕4 601 436-132 25 1.19 2.881 1∕4 x 1 601 436-168 25 1.00 2.00

1 1∕4 x 1 1∕2 601 436-169 25 0.94 2.311 1∕2 x 1 1∕4 601 436-212 25 1.19 2.50

1 1∕2 x 2 601 436-213 10 1.25 2.632 x 1 1∕2 601 436-251 10 1.25 2.56

193

194194

Reducer Bushing (SPG x S)

Size(inch)


HL(inch)

L(inch)

3∕4 x 1∕2 601 437-101 100 0.25 1.061 x 1∕2 601 437-130 100 0.50 1.251 x 3∕4 601 437-131 100 0.44 1.25

1 1∕4 x 1∕2 601 437-166 25 0.81 1.561 1∕4 x 3∕4 601 437-167 25 0.75 1.501 1∕4 x 1 601 437-168 25 0.44 1.501 1∕2 x 1∕2 601 437-209 25 0.88 1.631 1∕2 x 3∕4 601 437-210 25 0.81 1.631 1∕2 x 1 601 437-211 25 0.69 1.69

1 1∕2 x 1 1∕4 601 437-212 25 0.38 1.562 x 1∕2 601 437-247 10 0.94 1.692 x 1 601 437-249 10 0.56 1.632 x 3∕4 601 437-248 10 0.88 1.69

2 x 1 1∕4 601 437-250 10 0.44 1.692 x 1 1∕2 601 437-251 25 0.38 1.692 1∕2 x 1 601 437-289 10 1.31 2.31

2 1∕2 x 1 1∕4 601 437-290 10 1.00 2.252 1∕2 x 1 1∕2 601 437-291 10 1.00 2.31

2 1∕2 x 2 601 437-292 10 0.88 2.253 x 1 601 437-335 10 1.44 2.38

3 x 1 1∕4 601 437-336 10 1.25 2.443 x 1 1∕2 601 437-337 10 1.13 2.38

3 x 2 601 437-338 10 1.00 2.383 x 2 1∕2 601 437-339 10 0.38 2.38

4 x 2 601 437-420 5 1.00 2.384 x 2 1∕2 601 437-421 5 0.56 2.44

4 x 3 601 437-422 5 0.38 2.386 x 3 601 437-530 5 2.06 4.066 x 4 601 437-532 5 2.00 4.008 x 4 601 437-582 5 3.25 5.258 x 6 601 437-585 5 1.75 5.25

10 x 4 B09 437-624 1 4.38 6.3810 x 6 B09 437-626 1 2.44 5.4410 x 8 B09 437-628 1 1.38 5.4412 x 3 B09 437-661 1 5.38 7.3812 x 4 B09 437-664 1 5.63 7.6312 x 6 B09 437-666 1 4.13 7.6912 x 8 B09 437-668 1 2.38 6.44

12 x 10 B09 437-670 1 1.44 6.50

194

195194

Reducer Bushing (SPG x S)

Size(inch)


HL(inch)

L(inch)

3∕4 x 1∕2 601 437-101 100 0.25 1.061 x 1∕2 601 437-130 100 0.50 1.251 x 3∕4 601 437-131 100 0.44 1.25

1 1∕4 x 1∕2 601 437-166 25 0.81 1.561 1∕4 x 3∕4 601 437-167 25 0.75 1.501 1∕4 x 1 601 437-168 25 0.44 1.501 1∕2 x 1∕2 601 437-209 25 0.88 1.631 1∕2 x 3∕4 601 437-210 25 0.81 1.631 1∕2 x 1 601 437-211 25 0.69 1.69

1 1∕2 x 1 1∕4 601 437-212 25 0.38 1.562 x 1∕2 601 437-247 10 0.94 1.692 x 1 601 437-249 10 0.56 1.632 x 3∕4 601 437-248 10 0.88 1.69

2 x 1 1∕4 601 437-250 10 0.44 1.692 x 1 1∕2 601 437-251 25 0.38 1.692 1∕2 x 1 601 437-289 10 1.31 2.31

2 1∕2 x 1 1∕4 601 437-290 10 1.00 2.252 1∕2 x 1 1∕2 601 437-291 10 1.00 2.31

2 1∕2 x 2 601 437-292 10 0.88 2.253 x 1 601 437-335 10 1.44 2.38

3 x 1 1∕4 601 437-336 10 1.25 2.443 x 1 1∕2 601 437-337 10 1.13 2.38

3 x 2 601 437-338 10 1.00 2.383 x 2 1∕2 601 437-339 10 0.38 2.38

4 x 2 601 437-420 5 1.00 2.384 x 2 1∕2 601 437-421 5 0.56 2.44

4 x 3 601 437-422 5 0.38 2.386 x 3 601 437-530 5 2.06 4.066 x 4 601 437-532 5 2.00 4.008 x 4 601 437-582 5 3.25 5.258 x 6 601 437-585 5 1.75 5.25

10 x 4 B09 437-624 1 4.38 6.3810 x 6 B09 437-626 1 2.44 5.4410 x 8 B09 437-628 1 1.38 5.4412 x 3 B09 437-661 1 5.38 7.3812 x 4 B09 437-664 1 5.63 7.6312 x 6 B09 437-666 1 4.13 7.6912 x 8 B09 437-668 1 2.38 6.44

12 x 10 B09 437-670 1 1.44 6.50

195

Reducer Bushing (SPG x FPT)

Size(inch)


L(inch)

T(inch)

1∕2 x 1∕4 601 438-072 100 1.19 0.691∕2 x 3∕8 601 438-073 100 1.25 0.633∕4 x 1∕4 601 438-098 50 1.13 0.633∕4 x 1∕2 601 438-101 100 1.06 0.811 x 1∕2 601 438-130 100 1.25 0.751 x 3∕4 601 438-131 100 1.25 0.69

1 1∕4 x 1∕2 601 438-166 25 1.56 1.061 1∕4 x 3∕4 601 438-167 25 1.56 0.751 1∕4 x 1 601 438-168 25 1.56 1.001 1∕2 x 1∕2 601 438-209 25 1.56 0.691 1∕2 x 3∕4 601 438-210 25 1.56 0.691 1∕2 x 1 601 438-211 25 1.56 0.88

1 1∕2 x 1 1∕4 601 438-212 25 1.63 1.382 x 1∕2 601 438-247 10 1.69 0.752 x 3∕4 601 438-248 10 1.69 0.692 x 1 601 438-249 10 1.75 1.13

2 x 1 1∕4 601 438-250 10 1.69 1.382 x 1 1∕2 601 438-251 10 1.69 0.94

2 1∕2 x 1 1∕2 601 438-291 10 2.31 1.312 1∕2 x 2 601 438-292 10 2.31 1.503 x 1 1∕2 601 438-337 10 2.38 0.88

3 x 2 601 438-338 10 2.38 1.003 x 2 1∕2 601 438-339 10 2.38 1.50

4 x 2 601 438-420 5 2.44 1.004 x 2 1∕2 601 438-421 5 2.44 1.31

4 x 3 601 438-422 5 2.38 1.386 x 4 601 438-532 5 3.88 1.69

Reducer Bushing (MPT x FPT)

Size(inch)


L(inch)

T(inch)

1∕2 x 1∕4 601 439-072 50 1.13 0.631∕2 x 3∕8 601 439-073 50 1.13 0.693∕4 x 1∕4 601 439-098 50 1.13 0.693∕4 x 1∕2 601 439-101 50 1.00 0.751 x 1∕2 601 439-130 50 1.06 0.751 x 3∕4 601 439-131 50 1.13 0.75

1 1∕4 x 1∕2 601 439-166 25 1.31 0.751 1∕4 x 3∕4 601 439-167 25 1.31 0.501 1∕4 x 1 601 439-168 25 1.31 1.001 1∕2 x 1∕2 601 439-209 25 1.38 0.751 1∕2 x 3∕4 601 439-210 25 1.44 0.811 1∕2 x 1 601 439-211 25 1.44 1.13

1 1∕2 x 1 1∕4 601 439-212 25 1.44 1.002 x 1 601 439-249 10 1.44 1.00

2 x 1 1∕4 601 439-250 10 1.44 1.002 x 1 1∕2 601 439-251 10 1.50 1.002 1∕2 x 2 601 439-292 10 1.81 1.06

3 x 2 601 439-338 5 2.06 1.06

195

196196

Cap (S)

Size(inch)


W(inch)

Design

1∕2 601 447-005 100 1.193∕4 601 447-007 100 1.311 601 447-010 50 1.75

1 1∕4 601 447-012 25 1.751 1∕2 601 447-015 25 2.00

2 601 447-020 25 2.192 1∕2 601 447-025 10 3.06

3 601 447-030 10 3.194 601 447-040 5 3.506 601 447-060 5 5.388 601 447-080 4 6.69

10 B09 447-100 1 8.5012 B09 447-120 1 9.6314 A32 447-140N 1 5.00 FAB16 A32 447-160N 1 5.25 FAB18 A32 447-180N 1 6.25 FAB20 A32 447-200N 1 6.75 FAB24 A32 447-240N 1 8.00 FAB

Cap (FPT)

Size(inch)


W(inch)

T(inch)

1∕2 601 448-005 100 1.06 0.753∕4 601 448-007 100 1.13 0.811 601 448-010 50 1.25 1.00

1 1∕4 601 448-012 25 1.50 1.311 1∕2 601 448-015 25 1.56 1.06

2 601 448-020 10 1.75 1.442 1∕2 601 448-025 10 2.56 2.13

3 601 448-030 10 3.13 2.004 601 448-040 5 3.25 2.19

196

197196

Cap (S)

Size(inch)


W(inch)

Design

1∕2 601 447-005 100 1.193∕4 601 447-007 100 1.311 601 447-010 50 1.75

1 1∕4 601 447-012 25 1.751 1∕2 601 447-015 25 2.00

2 601 447-020 25 2.192 1∕2 601 447-025 10 3.06

3 601 447-030 10 3.194 601 447-040 5 3.506 601 447-060 5 5.388 601 447-080 4 6.69

10 B09 447-100 1 8.5012 B09 447-120 1 9.6314 A32 447-140N 1 5.00 FAB16 A32 447-160N 1 5.25 FAB18 A32 447-180N 1 6.25 FAB20 A32 447-200N 1 6.75 FAB24 A32 447-240N 1 8.00 FAB

Cap (FPT)

Size(inch)


W(inch)

T(inch)

1∕2 601 448-005 100 1.06 0.753∕4 601 448-007 100 1.13 0.811 601 448-010 50 1.25 1.00

1 1∕4 601 448-012 25 1.50 1.311 1∕2 601 448-015 25 1.56 1.06

2 601 448-020 10 1.75 1.442 1∕2 601 448-025 10 2.56 2.13

3 601 448-030 10 3.13 2.004 601 448-040 5 3.25 2.19

197

Plug (SPG)

Size(inch)


L(inch)

R(inch)

1∕2 601 449-005 50 1.00 0.253∕4 601 449-007 50 1.06 0.251 601 449-010 50 1.25 0.25

1 1∕4 601 449-012 25 1.56 0.311 1∕2 601 449-015 25 1.63 0.31

2 601 449-020 10 1.69 0.312 1∕2 601 449-025 10 2.38 0.38

3 601 449-030 10 2.38 0.384 601 449-040 5 2.38 0.38

Plug (MPT)

Size(inch)


L(inch)

R(inch)

1∕2 601 450-005 50 1.00 0.253∕4 601 450-007 50 1.06 0.311 601 450-010 50 1.13 0.31

1 1∕4 601 450-012 25 1.25 0.441 1∕2 601 450-015 25 1.38 0.31

2 601 450-020 10 1.38 0.312 1∕2 601 450-025 10 1.94 0.38

3 601 450-030 10 2.00 0.314 601 450-040 5 2.13 0.386 A32 450-060N 1 2.00 1.008 A32 450-080N 1 2.00 1.00

10 A32 450-100N 1 2.00 1.0012 A32 450-120N 1 2.00 1.00

197

198198

Union (S x S)

• 150 psi @ 73ºF (10.3 bar @ 22.7ºC)• O-ring material Buna-N Size(inch)


L(inch)

N(inch)

1∕2 601 457-005 10 1.75 0.253∕4 601 457-007 10 1.88 0.251 601 457-010 10 2.38 0.25

1 1∕4 601 457-012 5 2.81 0.381 1∕2 601 457-015 5 3.00 0.38

2 601 457-020 5 3.13 0.38

Union (FPT x FPT)

• 150 psi @ 73ºF (10.3 bar @ 22.7ºC)• O-ring material Buna-N Size(inch)


L(inch)

T(inch)

1∕2 601 458-005 10 1.75 0.753∕4 601 458-007 10 1.88 0.811 601 458-010 10 2.44 1.06

1 1∕4 601 458-012 5 2.81 1.131 1∕2 601 458-015 5 3.00 1.06

2 601 458-020 5 3.13 1.19

198

107106

GF Piping Systems

Schedule 80 PVC Piping Systems

Section 1

107

108107

Glossary



S = Tapered Socket




HS = High Strength Design

SL = Streamline Design







108

109107

Glossary



S = Tapered Socket




HS = High Strength Design

SL = Streamline Design







109

Table of contents Page

Harvel®Industrial PVC Pressure Pipe 111

Harvel® Industrial PLUS PVC Pressure Pipe 112

Schedule 80 PVC Pressure Fittings 113

Schedule 80 PVC Low Pressure Fittings 133

Schedule 80 PVC DWV Fittings 135

Schedule 80 PVC Metal Transition Fittings 138

Schedule 80 PVC Expansion Joints 140

109

110110

Specifications, Standards and Tolerances



ASTM D 1784 : Material PVC Type I, Grade I Gray (cell classification 12454)


ASTM D 2467 : PVC Schedule 80 Socket & Threaded Fittings

ASTM D 2464 : PVC Schedule 80 Threaded Fittings



ASTM F 1970 : PVC Schedule 80 Unions

ANSI B16.5 : Outside Diameter & Flange Bolt Hole Patterns


CSA B137.3 : PVC Schedule 80 Pipe

Molded Dimension TolerancesA Piston Position; Expansion Joints : ±0.03

D Outside Diameter : ± 0.06

G, G1 Intersections of centerlines to bottom of socket; 90° Ells, Tees : up to 4" ±0.03; 6" and above ±0.06

GJ, GN Intersections of centerlines to bottom of socket; 45° Wyes : up to 4" ±0.03; 6" and above ±0.06

H, HJ, HN Intersections of centerlines to face of fitting; 90° Ells, 45° Ells, Tees, 45° Wyes : up to 4" ±0.03; 6" and above ±0.06

HL Socket Bottom to Face of Fitting : up to 4" ±0.03; 6" and above ±0.06

J Intersections of centerlines to bottom of socket; 45° & 30° Ells : up to 4" ±0.03; 6" and above ±0.06

L Overall Length of fitting : ± 0.06

N Socket Bottom to Socket Bottom; Couplings, Unions : ± 0.06

N1 Socket Bottom to Face of Flange : ± 0.06

R Thickness on Plugs, Flanges : ± 0.03

T, T1 Effective Thread Length : Reference Only

W Height of Cap : ± 0.06

110

111110

Specifications, Standards and Tolerances



ASTM D 1784 : Material PVC Type I, Grade I Gray (cell classification 12454)


ASTM D 2467 : PVC Schedule 80 Socket & Threaded Fittings

ASTM D 2464 : PVC Schedule 80 Threaded Fittings



ASTM F 1970 : PVC Schedule 80 Unions

ANSI B16.5 : Outside Diameter & Flange Bolt Hole Patterns


CSA B137.3 : PVC Schedule 80 Pipe

Molded Dimension TolerancesA Piston Position; Expansion Joints : ±0.03

D Outside Diameter : ± 0.06

G, G1 Intersections of centerlines to bottom of socket; 90° Ells, Tees : up to 4" ±0.03; 6" and above ±0.06

GJ, GN Intersections of centerlines to bottom of socket; 45° Wyes : up to 4" ±0.03; 6" and above ±0.06

H, HJ, HN Intersections of centerlines to face of fitting; 90° Ells, 45° Ells, Tees, 45° Wyes : up to 4" ±0.03; 6" and above ±0.06

HL Socket Bottom to Face of Fitting : up to 4" ±0.03; 6" and above ±0.06

J Intersections of centerlines to bottom of socket; 45° & 30° Ells : up to 4" ±0.03; 6" and above ±0.06

L Overall Length of fitting : ± 0.06

N Socket Bottom to Socket Bottom; Couplings, Unions : ± 0.06

N1 Socket Bottom to Face of Flange : ± 0.06

R Thickness on Plugs, Flanges : ± 0.03

T, T1 Effective Thread Length : Reference Only

W Height of Cap : ± 0.06

111

Harvel® Industrial PVC Pressure Pipe


• Refer to Industrial PLUS for sizes 1/8", 1/4", 3/8", 3-1/2", 5", 14"-24"• Max Water Pressure at 73°F (22.7°C) with solvent-cemented joints• Meets NSF®-pw-G• Non - CSA Approved Size(inch)


Lift Qty.(20ft

Lgths)( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

Max WaterPressure

(psi)

1/2 H18 H0800050PG2000 5700 0.840 0.147 0.202 8503/4 H18 H0800075PG2000 5260 1.050 0.154 0.273 690

1 H18 H0800100PG2000 4280 1.315 0.179 0.402 6301 1/4 H18 H0800125PG2000 2360 1.660 0.191 0.554 5201 1/2 H18 H0800150PG2000 2060 1.900 0.200 0.673 470

2 H18 H0800200PG2000 1660 2.375 0.218 0.932 4002 1/2 H18 H0800250PG2000 1080 2.875 0.276 1.419 420

3 H18 H0800300PG2000 840 3.500 0.300 1.903 3704 H18 H0800400PG2000 520 4.500 0.337 2.782 3206 H18 H0800600PG2000 340 6.625 0.432 5.313 2808 H18 H0800800PG2000 220 8.625 0.500 8.058 250

10 H18 H0801000PG2000 80 10.750 0.593 11.956 23012 H18 H0801200PG2000 60 12.750 0.687 16.437 230


Size(inch)



Pipe)


C-Min.(Belled

Pipe)1∕2 H18 H0800050PG200B 0.848±0.004 0.836±0.004 1.0003∕4 H18 H0800075PG200B 1.058±0.004 1.046±0.004 1.2501 H18 H0800100PG200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H18 H0800125PG200B 1.678±0.002 1.653±0.005 1.8701 1∕2 H18 H0800150PG200B 1.910±0.004 1.884±0.004 2.000

2 H18 H0800200PG200B 2.387±0.006 2.369±0.006 2.2502 1∕2 H18 H0800250PG200B 2.889±0.007 2.868±0.007 2.500

3 H18 H0800300PG200B 3.516±0.008 3.492±0.008 3.2504 H18 H0800400PG200B 4.518±0.009 4.491±0.009 4.0006 H18 H0800600PG200B 6.647±0.011 6.614±0.011 6.0008 H18 H0800800PG200B 8.655±0.015 8.610±0.015 6.000

10 H18 H0801000PG200B 10.776±0.015 10.737±0.015 8.00012 H18 H0801200PG200B 12.778±0.015 12.736±0.015 8.500

111

112112

Harvel® Industrial PLUS PVC Pressure Pipe


• Meets NSF®-pw-G• Meets CAN/CSA B137.3 Requirements Size(inch)


Lift Qty.(20ft

Lgths)( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

MaxWaterPres-sure

(psi)1∕8 H50 H0800013PG2000 5700 0.405 0.095 0.058 12301∕4 H50 H0800025PG2000 5700 0.540 0.119 0.100 11303∕8 H50 H0800038PG2000 5700 0.675 0.126 0.138 9201∕2 H50 HX800050PG2000 5700 0.840 0.147 0.202 8503∕4 H50 HX800075PG2000 5260 1.050 0.154 0.273 6901 H50 HX800100PG2000 4280 1.315 0.179 0.402 630

1 1∕4 H50 HX800125PG2000 2360 1.660 0.191 0.554 5201 1∕2 H50 HX800150PG2000 2060 1.900 0.200 0.673 470

2 H50 HX800200PG2000 1660 2.375 0.218 0.932 4002 1∕2 H50 HX800250PG2000 1080 0.287 0.276 1.419 420

3 H50 HX800300PG2000 840 3.500 0.300 1.903 3703 1∕2 H50 H0800350PG2000 680 4.000 0.318 2.322 350

4 H50 HX800400PG2000 520 4.500 0.337 2.782 3205 H50 H0800500PG2000 400 5.563 0.375 3.867 2906 H50 HX800600PG2000 340 6.625 0.432 5.313 2808 H50 HX800800PG2000 220 8.625 0.500 8.058 250

10 H50 HX801000PG2000 80 10.750 0.593 11.956 23012 H50 HX801200PG2000 60 12.750 0.687 16.437 23014 H50 H0801400PG2000 60 14.000 0.750 19.790 22016 H50 H0801600PG2000 60 16.000 0.843 25.430 22018 H50 H0801800PG2000 40 18.000 0.937 31.830 22020 H50 H0802000PG2000 40 20.000 1.031 40.091 22024 H50 H0802400PG2000 40 24.000 1.218 56.882 210


Size(inch)



Pipe)


C-Min.(Belled

Pipe)1∕2 H50 HX800050PG200B 0.848±0.004 0.836±0.004 1.0003∕4 H50 HX800075PG200B 1.058±0.004 1.046±0.004 1.2501 H50 HX800100PG200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H50 HX800125PG200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H50 HX800150PG200B 1.912±0.006 1.894±0.006 2.000

2 H50 HX800200PG200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H50 HX800250PG200B 2.889±0.007 2.861±0.007 2.500

3 H50 HX800300PG200B 3.516±0.008 3.484±0.008 3.2503 1∕2 H50 H0800350PG200B 4.016±0.008 3.984±0.008 3.500

4 H50 HX800400PG200B 4.518±0.009 4.482±0.009 4.0005 H50 H0800500PG200B 5.583±0.010 5.543±0.010 4.0006 H50 HX800600PG200B 6.647±0.011 6.603±0.011 6.0008 H50 HX800800PG200B 8.655±0.015 8.598±0.015 6.000

10 H50 HX801000PG200B 10.776±0.015 10.722±0.015 7.50012 H50 HX801200PG200B 12.778±0.015 12.721±0.015 8.50014 H50 H0801400PG200B 14.035±0.015 13.985±0.015 9.00016 H50 H0801600PG200B 16.045±0.015 15.980±0.015 10.00018 H50 H0801800PG200B 18.055±0.020 17.980±0.020 12.00020 H50 H0802000PG200B 20.065±0.025 19.980±0.025 12.00024 H50 H0802400PG200B 24.075±0.030 23.970±0.030 12.000

112

113112

Harvel® Industrial PLUS PVC Pressure Pipe


• Meets NSF®-pw-G• Meets CAN/CSA B137.3 Requirements Size(inch)


Lift Qty.(20ft

Lgths)( ft)

AverageO.D.(inch)

Min. Wall(inch)

Wt/Ft(lbs ⁄ ft)

MaxWaterPres-sure

(psi)1∕8 H50 H0800013PG2000 5700 0.405 0.095 0.058 12301∕4 H50 H0800025PG2000 5700 0.540 0.119 0.100 11303∕8 H50 H0800038PG2000 5700 0.675 0.126 0.138 9201∕2 H50 HX800050PG2000 5700 0.840 0.147 0.202 8503∕4 H50 HX800075PG2000 5260 1.050 0.154 0.273 6901 H50 HX800100PG2000 4280 1.315 0.179 0.402 630

1 1∕4 H50 HX800125PG2000 2360 1.660 0.191 0.554 5201 1∕2 H50 HX800150PG2000 2060 1.900 0.200 0.673 470

2 H50 HX800200PG2000 1660 2.375 0.218 0.932 4002 1∕2 H50 HX800250PG2000 1080 0.287 0.276 1.419 420

3 H50 HX800300PG2000 840 3.500 0.300 1.903 3703 1∕2 H50 H0800350PG2000 680 4.000 0.318 2.322 350

4 H50 HX800400PG2000 520 4.500 0.337 2.782 3205 H50 H0800500PG2000 400 5.563 0.375 3.867 2906 H50 HX800600PG2000 340 6.625 0.432 5.313 2808 H50 HX800800PG2000 220 8.625 0.500 8.058 250

10 H50 HX801000PG2000 80 10.750 0.593 11.956 23012 H50 HX801200PG2000 60 12.750 0.687 16.437 23014 H50 H0801400PG2000 60 14.000 0.750 19.790 22016 H50 H0801600PG2000 60 16.000 0.843 25.430 22018 H50 H0801800PG2000 40 18.000 0.937 31.830 22020 H50 H0802000PG2000 40 20.000 1.031 40.091 22024 H50 H0802400PG2000 40 24.000 1.218 56.882 210


Size(inch)



Pipe)


C-Min.(Belled

Pipe)1∕2 H50 HX800050PG200B 0.848±0.004 0.836±0.004 1.0003∕4 H50 HX800075PG200B 1.058±0.004 1.046±0.004 1.2501 H50 HX800100PG200B 1.325±0.005 1.310±0.005 1.500

1 1∕4 H50 HX800125PG200B 1.670±0.005 1.655±0.005 1.7501 1∕2 H50 HX800150PG200B 1.912±0.006 1.894±0.006 2.000

2 H50 HX800200PG200B 2.387±0.006 2.363±0.006 2.2502 1∕2 H50 HX800250PG200B 2.889±0.007 2.861±0.007 2.500

3 H50 HX800300PG200B 3.516±0.008 3.484±0.008 3.2503 1∕2 H50 H0800350PG200B 4.016±0.008 3.984±0.008 3.500

4 H50 HX800400PG200B 4.518±0.009 4.482±0.009 4.0005 H50 H0800500PG200B 5.583±0.010 5.543±0.010 4.0006 H50 HX800600PG200B 6.647±0.011 6.603±0.011 6.0008 H50 HX800800PG200B 8.655±0.015 8.598±0.015 6.000

10 H50 HX801000PG200B 10.776±0.015 10.722±0.015 7.50012 H50 HX801200PG200B 12.778±0.015 12.721±0.015 8.50014 H50 H0801400PG200B 14.035±0.015 13.985±0.015 9.00016 H50 H0801600PG200B 16.045±0.015 15.980±0.015 10.00018 H50 H0801800PG200B 18.055±0.020 17.980±0.020 12.00020 H50 H0802000PG200B 20.065±0.025 19.980±0.025 12.00024 H50 H0802400PG200B 24.075±0.030 23.970±0.030 12.000



Tee (S x S x S) Schedule 80 Harvel® PVC

Size(inch)


H(inch)

G(inch)

Design

1∕4 608 801-002 50 0.95 0.27 HS3∕8 608 801-003 50 1.16 0.38 HS1∕2 608 801-005 25 1.41 0.51 SL3∕4 608 801-007 25 1.60 0.58 SL1 608 801-010 20 1.85 0.71 SL

1 1∕4 608 801-012 10 2.17 0.91 SL1 1∕2 608 801-015 10 2.43 1.04 SL

2 608 801-020 10 2.81 1.30 SL2 1∕2 608 801-025 5 3.31 1.55 SL

3 608 801-030 5 3.71 1.81 SL4 608 801-040 5 4.60 2.33 SL6 608 801-060 2 6.53 3.51 SL8 608 801-080 1 8.66 4.58 SL

10 602 801-100 1 10.79 5.78 SL12 602 801-120 1 12.96 6.94 SL14 A33 801-140N 1 19.50 10.88 FAB16 A33 801-160N 1 22.75 12.13 FAB18 A33 801-180N 1 26.00 13.38 FAB20 A33 801-200N 1 28.25 14.63 FAB24 A33 801-240N 1 34.50 17.13 FAB

Reducing Tee (S x S x S) Schedule 80 Harvel® PVC

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

3∕4 x 1∕2 608 801-101 25 1.62 1.62 0.60 0.72 SL1 x 1∕2 608 801-130 25 1.87 1.64 0.72 0.74 SL1 x 3∕4 608 801-131 20 1.86 1.89 0.72 0.75 SL

1 1∕4 x 1∕2 608 801-166FB 20 1.99 2.35 0.73 1.47 BUSH1 1∕4 x 3∕4 608 801-167FB 20 1.99 2.35 0.73 1.33 BUSH1 1∕4 x 1 608 801-168 20 2.01 2.05 0.73 0.91 SL1 1∕2 x 1∕2 608 801-209 5 1.92 1.91 0.53 1.03 SL1 1∕2 x 3∕4 608 801-210 5 1.99 2.07 0.60 1.05 SL1 1∕2 x 1 608 801-211 5 2.12 2.17 0.72 1.03 SL

1 1∕2 x 1 1∕4 608 801-212FB 5 2.44 2.74 1.04 1.47 BUSH2 x 1∕2 608 801-247 5 1.99 2.16 0.54 1.28 SL2 x 3∕4 608 801-248 5 2.22 2.31 0.60 1.30 SL2 x 1 608 801-249 5 2.24 2.42 0.72 1.27 SL

2 x 1 1∕4 608 801-250FB 5 2.81 3.11 1.30 1.84 BUSH2 x 1 1∕2 608 801-251 5 2.54 2.66 1.03 1.27 SL2 1∕2 x 1∕2 608 801-287FB 5 3.05 3.35 1.28 2.44 BUSH2 1∕2 x 3∕4 608 801-288FB 5 3.05 3.35 1.28 2.33 BUSH2 1∕2 x 1 608 801-289FB 5 3.05 3.36 1.28 2.22 BUSH

2 1∕2 x 1 1∕4 608 801-290FB 5 3.05 3.34 1.28 2.07 BUSH2 1∕2 x 1 1∕2 608 801-291FB 5 3.05 3.35 1.28 1.94 BUSH

2 1∕2 x 2 608 801-292 5 3.05 3.05 1.28 1.54 SL3 x 1∕2 608 801-333FB 5 3.20 3.68 1.30 2.77 BUSH3 x 3∕4 608 801-334FB 5 3.20 3.68 1.30 2.66 BUSH3 x 1 608 801-335FB 5 3.20 3.69 1.30 2.55 BUSH

3 x 1 1∕4 608 801-336FB 5 3.20 3.67 1.30 2.40 BUSH3 x 1 1∕2 608 801-337FB 5 3.20 3.68 1.30 2.27 BUSH

3 x 2 608 801-338 5 3.20 3.39 1.30 1.87 SL3 x 2 1∕2 608 801-339FB 5 3.73 4.07 1.81 2.17 BUSH

4 x 1∕2 608 801-415FB 5 3.52 4.19 1.27 3.28 BUSH4 x 3∕4 608 801-416FB 5 3.52 4.19 1.27 3.17 BUSH

113

114


Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

4 x 1 608 801-417 5 2.99 3.49 0.74 2.36 SL4 x 1 1∕4 608 801-418FB 5 3.52 4.18 1.27 2.91 BUSH4 x 1 1∕2 608 801-419FB 5 3.52 4.19 1.27 2.78 BUSH

4 x 2 608 801-420 5 3.54 3.87 1.27 2.37 SL4 x 2 1∕2 608 801-421FB 5 4.14 4.62 1.85 2.73 BUSH

4 x 3 608 801-422 5 4.13 4.26 1.85 2.35 SL6 x 1∕2 608 801-523FB 2 6.56 7.42 3.56 6.52 BUSH6 x 3∕4 608 801-524FB 2 6.56 7.43 3.49 6.41 BUSH6 x 1 608 801-525FB 2 6.56 7.44 3.49 6.29 BUSH

6 x 1 1∕4 608 801-526FB 2 6.56 7.42 3.49 6.15 BUSH6 x 1 1∕2 608 801-527FB 2 6.56 7.42 3.49 6.02 BUSH

6 x 2 608 801-528 2 4.45 5.25 1.43 3.74 SL6 x 2 1∕2 608 801-529FB 2 6.56 7.52 3.49 5.62 BUSH

6 x 3 608 801-530FB 2 6.56 7.21 3.49 5.25 BUSH6 x 4 608 801-532 2 6.57 6.80 3.49 4.47 HS6 x 5 H04 801-533FS 1 9.00 9.50 5.75 6.50 FAB8 x 4 608 801-582 2 8.41 8.53 4.29 6.30 SL8 x 6 608 801-585 1 7.65 7.54 3.55 4.63 SL

10 x 1 1∕2 A33 801-618N 1 10.75 12.45 5.75 11.04 FAB10 x 2 A33 801-619N 1 10.75 11.50 5.75 9.50 FAB10 x 3 A33 801-621N 1 10.75 11.50 5.25 9.50 FAB10 x 4 A33 801-623N 1 10.75 11.50 5.75 9.50 FAB10 x 6 602 801-626FB 1 10.83 11.43 5.78 8.33 BUSH10 x 6 A33 801-626N 1 11.88 12.50 6.88 9.50 FAB10 x 8 602 801-628FB 1 10.83 11.46 5.78 7.36 BUSH10 x 8 A33 801-628N 1 13.00 13.50 8.00 9.50 FAB12 x 2 A33 801-659N 1 12.00 12.75 6.00 10.75 FAB12 x 3 A33 801-661N 1 12.00 12.75 6.00 10.75 FAB12 x 4 A33 801-663N 1 12.00 12.75 6.00 10.75 FAB12 x 6 A33 801-666N 1 13.13 13.75 7.13 10.75 FAB12 x 8 602 801-668FB 1 12.99 13.67 6.94 9.58 BUSH12 x 8 A33 801-668N 1 14.13 14.75 8.13 10.75 FAB

12 x 10 602 801-670FB 1 12.99 13.68 6.94 8.57 BUSH12 x 10 A33 801-670N 1 15.13 15.75 9.13 10.75 FAB

14 x 2 A33 801-692N 1 13.13 13.50 6.13 11.50 FAB14 x 3 A33 801-694N 1 12.63 13.50 6.13 11.50 FAB14 x 4 A33 801-696N 1 13.13 13.50 6.13 11.50 FAB14 x 6 A33 801-698N 1 14.25 14.50 7.25 11.50 FAB14 x 8 A33 801-700N 1 15.25 15.50 8.25 11.50 FAB

14 x 10 A33 801-702N 1 16.25 16.50 9.25 11.50 FAB14 x 12 A33 801-704N 1 17.25 18.50 10.25 12.50 FAB


16 x 10 A33 801-736N 1 17.50 17.75 9.50 12.75 FAB16 x 12 A33 801-738N 1 18.50 19.75 10.50 13.75 FAB16 x 14 A33 801-740N 1 19.13 20.75 11.13 13.75 FAB


18 x 10 A33 801-790N 1 18.75 19.00 9.75 14.00 FAB18 x 12 A33 801-792N 1 19.75 21.00 10.75 15.00 FAB18 x 14 A33 801-794N 1 20.38 22.00 11.38 15.00 FAB18 x 16 A33 801-796N 1 21.38 24.00 12.38 16.00 FAB



114

115


Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design

4 x 1 608 801-417 5 2.99 3.49 0.74 2.36 SL4 x 1 1∕4 608 801-418FB 5 3.52 4.18 1.27 2.91 BUSH4 x 1 1∕2 608 801-419FB 5 3.52 4.19 1.27 2.78 BUSH

4 x 2 608 801-420 5 3.54 3.87 1.27 2.37 SL4 x 2 1∕2 608 801-421FB 5 4.14 4.62 1.85 2.73 BUSH

4 x 3 608 801-422 5 4.13 4.26 1.85 2.35 SL6 x 1∕2 608 801-523FB 2 6.56 7.42 3.56 6.52 BUSH6 x 3∕4 608 801-524FB 2 6.56 7.43 3.49 6.41 BUSH6 x 1 608 801-525FB 2 6.56 7.44 3.49 6.29 BUSH

6 x 1 1∕4 608 801-526FB 2 6.56 7.42 3.49 6.15 BUSH6 x 1 1∕2 608 801-527FB 2 6.56 7.42 3.49 6.02 BUSH

6 x 2 608 801-528 2 4.45 5.25 1.43 3.74 SL6 x 2 1∕2 608 801-529FB 2 6.56 7.52 3.49 5.62 BUSH

6 x 3 608 801-530FB 2 6.56 7.21 3.49 5.25 BUSH6 x 4 608 801-532 2 6.57 6.80 3.49 4.47 HS6 x 5 H04 801-533FS 1 9.00 9.50 5.75 6.50 FAB8 x 4 608 801-582 2 8.41 8.53 4.29 6.30 SL8 x 6 608 801-585 1 7.65 7.54 3.55 4.63 SL

10 x 1 1∕2 A33 801-618N 1 10.75 12.45 5.75 11.04 FAB10 x 2 A33 801-619N 1 10.75 11.50 5.75 9.50 FAB10 x 3 A33 801-621N 1 10.75 11.50 5.25 9.50 FAB10 x 4 A33 801-623N 1 10.75 11.50 5.75 9.50 FAB10 x 6 602 801-626FB 1 10.83 11.43 5.78 8.33 BUSH10 x 6 A33 801-626N 1 11.88 12.50 6.88 9.50 FAB10 x 8 602 801-628FB 1 10.83 11.46 5.78 7.36 BUSH10 x 8 A33 801-628N 1 13.00 13.50 8.00 9.50 FAB12 x 2 A33 801-659N 1 12.00 12.75 6.00 10.75 FAB12 x 3 A33 801-661N 1 12.00 12.75 6.00 10.75 FAB12 x 4 A33 801-663N 1 12.00 12.75 6.00 10.75 FAB12 x 6 A33 801-666N 1 13.13 13.75 7.13 10.75 FAB12 x 8 602 801-668FB 1 12.99 13.67 6.94 9.58 BUSH12 x 8 A33 801-668N 1 14.13 14.75 8.13 10.75 FAB

12 x 10 602 801-670FB 1 12.99 13.68 6.94 8.57 BUSH12 x 10 A33 801-670N 1 15.13 15.75 9.13 10.75 FAB


14 x 10 A33 801-702N 1 16.25 16.50 9.25 11.50 FAB14 x 12 A33 801-704N 1 17.25 18.50 10.25 12.50 FAB







115

Size(inch)


HJ(inch)

HN(inch)

G(inch)

G1(inch)

Design


24 x 10 A33 801-910N 1 22.50 22.50 10.50 17.50 FAB24 x 12 A33 801-912N 1 23.50 24.50 11.50 18.50 FAB24 x 14 A33 801-914N 1 24.13 25.50 12.13 18.50 FAB24 x 16 A33 801-916N 1 25.13 27.50 13.13 19.50 FAB24 x 18 A33 801-918N 1 26.13 30.50 14.13 20.50 FAB24 x 20 A33 801-920N 1 27.13 32.50 15.13 20.50 FAB

Tee (S x S x FPT) Schedule 80 Harvel® PVC

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

Design

1∕2 608 802-005 25 1.41 1.30 0.53 0.81 HS3∕4 608 802-007 25 1.60 1.37 0.60 0.71 HS1 608 802-010 15 1.83 1.73 0.69 0.99 HS

1 1∕2 608 802-015 5 2.41 2.08 1.02 1.04 HS2 608 802-020 5 2.79 2.37 1.29 1.08 HS

Tee (FPT x FPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


H(inch)

T(inch)

Design

1∕4 608 805-002 50 0.94 0.59 HS3∕8 608 805-003 50 1.01 0.60 HS1∕2 608 805-005 25 1.26 0.76 HS3∕4 608 805-007 25 1.36 0.72 HS1 608 805-010 15 1.79 0.99 HS

1 1∕4 608 805-012 10 1.93 1.01 HS1 1∕2 608 805-015 5 2.08 1.03 HS

2 608 805-020 5 2.39 1.06 HS2 1∕2 608 805-025 5 2.87 1.35 HS

3 608 805-030 5 3.52 1.65 HS4 608 805-040 5 4.07 1.72 HS

115

116116

90° Ell (S x S) Schedule 80 Harvel® PVC

Size(inch)


H(inch)

G(inch)

Design

1∕4 608 806-002 50 0.96 0.35 HS3∕8 608 806-003 50 1.15 0.39 HS1∕2 608 806-005 25 1.41 0.51 SL3∕4 608 806-007 25 1.60 0.57 SL1 608 806-010 10 1.83 0.68 SL

1 1∕4 608 806-012 10 2.18 0.90 SL1 1∕2 608 806-015 10 2.43 1.04 SL

2 608 806-020 20 2.80 1.27 SL2 1∕2 608 806-025 5 3.33 1.53 SL

3 608 806-030 5 3.73 1.81 SL4 608 806-040 5 4.63 2.32 SL6 608 806-060 2 6.56 3.53 SL8 608 806-080 1 8.68 4.55 SL


90° Ell (S x FPT) Schedule 80 Harvel® PVC

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

Design

1∕2 608 807-005 25 1.40 1.31 0.50 0.81 HS3∕4 608 807-007 25 1.59 1.36 0.58 0.72 HS1 608 807-010 10 1.81 1.70 0.67 1.00 HS

1 1∕4 608 807-012 10 2.15 1.92 0.90 1.03 HS1 1∕2 608 807-015 10 2.39 2.05 1.01 1.05 HS

2 608 807-020 5 2.77 2.36 1.24 1.09 HS3 608 807-030 5 3.73 3.47 1.83 1.66 HS

116

117116


Size(inch)


H(inch)

G(inch)

Design

1∕4 608 806-002 50 0.96 0.35 HS3∕8 608 806-003 50 1.15 0.39 HS1∕2 608 806-005 25 1.41 0.51 SL3∕4 608 806-007 25 1.60 0.57 SL1 608 806-010 10 1.83 0.68 SL

1 1∕4 608 806-012 10 2.18 0.90 SL1 1∕2 608 806-015 10 2.43 1.04 SL

2 608 806-020 20 2.80 1.27 SL2 1∕2 608 806-025 5 3.33 1.53 SL

3 608 806-030 5 3.73 1.81 SL4 608 806-040 5 4.63 2.32 SL6 608 806-060 2 6.56 3.53 SL8 608 806-080 1 8.68 4.55 SL


90° Ell (S x FPT) Schedule 80 Harvel® PVC

Size(inch)


HJ(inch)

HN(inch)

G(inch)

T(inch)

Design

1∕2 608 807-005 25 1.40 1.31 0.50 0.81 HS3∕4 608 807-007 25 1.59 1.36 0.58 0.72 HS1 608 807-010 10 1.81 1.70 0.67 1.00 HS

1 1∕4 608 807-012 10 2.15 1.92 0.90 1.03 HS1 1∕2 608 807-015 10 2.39 2.05 1.01 1.05 HS

2 608 807-020 5 2.77 2.36 1.24 1.09 HS3 608 807-030 5 3.73 3.47 1.83 1.66 HS

117

90° Ell (FPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


H(inch)

T(inch)

Design

1∕4 608 808-002 50 0.94 0.61 HS3∕8 608 808-003 50 1.00 0.63 HS1∕2 608 808-005 25 1.27 0.78 HS3∕4 608 808-007 25 1.36 0.72 HS1 608 808-010 10 1.71 1.00 HS

1 1∕4 608 808-012 10 1.92 1.01 HS1 1∕2 608 808-015 10 2.08 1.06 HS

2 608 808-020 5 2.36 1.08 HS2 1∕2 608 808-025 5 3.36 1.51 HS

3 608 808-030 5 3.53 1.63 HS4 608 808-040 5 4.17 1.75 HS


Size(inch)


H(inch)

J(inch)

Design

1∕4 608 817-002 50 0.81 0.18 HS3∕8 608 817-003 50 0.94 0.19 HS1∕2 608 817-005 25 1.22 0.30 SL3∕4 608 817-007 20 1.29 0.28 SL1 608 817-010 25 1.48 0.32 SL

1 1∕4 608 817-012 15 1.78 0.47 SL1 1∕2 608 817-015 10 1.88 0.45 SL

2 608 817-020 5 2.16 0.60 SL2 1∕2 608 817-025 5 2.56 0.79 SL

3 608 817-030 5 2.67 0.77 SL4 608 817-040 5 3.31 1.04 SL6 608 817-060 2 4.86 1.77 SL8 608 817-080 2 6.15 2.07 SL


117

118118


Size(inch)


H(inch)

T(inch)

Design

1∕4 608 819-002 50 0.69 0.59 HS3∕8 608 819-003 50 0.86 0.68 HS1∕2 608 819-005 25 1.02 0.76 SL3∕4 608 819-007 20 1.14 0.81 SL1 608 819-010 25 1.33 0.97 SL

1 1∕4 608 819-012 15 1.42 1.01 SL1 1∕2 608 819-015 10 1.47 1.07 SL

2 608 819-020 5 1.74 2.37 SL3 608 819-030 5 2.43 1.66 SL4 608 819-040 5 2.78 1.76 SL

Coupling (S x S) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

N(inch)

Design

3∕8 608 829-003 50 1.65 0.11 HS1∕2 608 829-005 25 1.93 0.12 SL3∕4 608 829-007 20 2.18 0.12 SL1 608 829-010 25 2.41 0.12 SL

1 1∕4 608 829-012 10 2.67 0.13 SL1 1∕2 608 829-015 10 2.94 0.15 SL

2 608 829-020 20 3.18 0.13 SL2 1∕2 608 829-025 5 3.77 0.19 SL

3 608 829-030 5 4.04 0.26 SL4 608 829-040 5 4.80 0.26 SL6 608 829-060 2 6.40 0.36 SL8 608 829-080 2 8.40 0.35 SL


118

119118


Size(inch)


H(inch)

T(inch)

Design

1∕4 608 819-002 50 0.69 0.59 HS3∕8 608 819-003 50 0.86 0.68 HS1∕2 608 819-005 25 1.02 0.76 SL3∕4 608 819-007 20 1.14 0.81 SL1 608 819-010 25 1.33 0.97 SL

1 1∕4 608 819-012 15 1.42 1.01 SL1 1∕2 608 819-015 10 1.47 1.07 SL

2 608 819-020 5 1.74 2.37 SL3 608 819-030 5 2.43 1.66 SL4 608 819-040 5 2.78 1.76 SL

Coupling (S x S) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

N(inch)

Design

3∕8 608 829-003 50 1.65 0.11 HS1∕2 608 829-005 25 1.93 0.12 SL3∕4 608 829-007 20 2.18 0.12 SL1 608 829-010 25 2.41 0.12 SL

1 1∕4 608 829-012 10 2.67 0.13 SL1 1∕2 608 829-015 10 2.94 0.15 SL

2 608 829-020 20 3.18 0.13 SL2 1∕2 608 829-025 5 3.77 0.19 SL

3 608 829-030 5 4.04 0.26 SL4 608 829-040 5 4.80 0.26 SL6 608 829-060 2 6.40 0.36 SL8 608 829-080 2 8.40 0.35 SL



Reducing Coupling (S x S) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

N(inch)

Design

3∕4 x 1∕2 608 829-101 20 2.13 0.13 HS1 x 1∕2 608 829-130 25 2.17 0.12 HS1 x 3∕4 608 829-131 25 2.26 0.11 HS

1 1∕4 x 1 608 829-168 10 2.52 0.10 HS1 1∕2 x 1∕2 608 829-209FB 10 2.94 0.66 BUSH1 1∕2 x 3∕4 608 829-210 10 2.50 0.09 BUSH1 1∕2 x 1 608 829-211 10 2.65 0.11 HS

1 1∕2 x 1 1∕4 608 829-212 10 2.82 0.09 HS2 x 1∕2 608 829-247FB 5 3.44 0.87 BUSH2 x 3∕4 608 829-248 5 3.14 0.34 HS2 x 1 608 829-249 5 3.15 0.32 HS

2 x 1 1∕4 608 829-250 5 3.05 0.14 HS2 x 1 1∕2 608 829-251 5 3.06 0.07 HS

2 1∕2 x 1 1∕2 608 829-291 5 3.36 0.14 HS2 1∕2 x 2 608 829-292FB 5 4.08 0.66 BUSH

3 x 1 608 829-335FB 5 4.56 1.53 BUSH3 x 1 1∕4 608 829-336FB 5 4.29 1.07 FAB3 x 1 1∕2 608 829-337FB 5 4.58 1.15 BUSH

3 x 2 608 829-338 5 3.61 0.17 HS3 x 2 1∕2 608 829-339FB 5 4.42 0.63 BUSH

4 x 2 608 829-420FB 5 4.94 1.08 BUSH4 x 3 608 829-422 5 4.38 0.22 HS6 x 2 608 829-528FB 2 10.61 4.60 BUSH6 x 4 608 829-532 2 10.17 3.46 HS8 x 4 608 829-582FB 2 9.81 3.53 BUSH8 x 6 608 829-585 2 9.18 2.11 HS

10 x 4 A33 829-623N 1 17.00 10.00 FAB10 x 6 602 829-626FB 1 11.42 3.29 BUSH10 x 6 A33 829-626N 1 13.00 5.00 FAB10 x 8 602 829-628FB 1 11.45 2.32 BUSH10 x 8 A33 829-628N 1 12.75 3.75 FAB12 x 4 A33 829-663N 1 26.25 18.25 FAB12 x 6 A33 829-666N 1 20.50 11.50 FAB12 x 8 602 829-668FB 1 13.54 3.41 BUSH12 x 8 A33 829-668N 1 15.50 5.50 FAB

12 x 10 602 829-670FB 1 13.24 2.13 BUSH12 x 10 A33 829-670N 1 15.00 4.00 FAB


14 x 10 A33 829-702N 1 17.00 5.00 FAB14 x 12 A33 829-704N 1 16.50 3.50 FAB






20 x 10 A33 829-820N 1 47.25 32.25 FAB20 x 12 A33 829-822N 1 37.00 21.00 FAB

119

120120

Size(inch)


L(inch)

N(inch)

Design




Coupling (FPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

Design

1∕4 608 830-002 50 1.29 0.61 HS3∕8 608 830-003 50 1.35 0.62 HS1∕2 608 830-005 25 1.68 0.77 SL3∕4 608 830-007 20 1.75 0.80 SL1 608 830-010 25 2.13 0.99 SL

1 1∕4 608 830-012 10 2.19 1.03 SL1 1∕2 608 830-015 10 2.22 1.03 SL

2 608 830-020 5 2.29 1.08 SL2 1∕2 608 830-025 5 3.33 1.51 SL

3 608 830-030 5 3.53 1.65 SL4 608 830-040 5 3.76 1.75 SL

120

121120

Size(inch)


L(inch)

N(inch)

Design




Coupling (FPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

Design

1∕4 608 830-002 50 1.29 0.61 HS3∕8 608 830-003 50 1.35 0.62 HS1∕2 608 830-005 25 1.68 0.77 SL3∕4 608 830-007 20 1.75 0.80 SL1 608 830-010 25 2.13 0.99 SL

1 1∕4 608 830-012 10 2.19 1.03 SL1 1∕2 608 830-015 10 2.22 1.03 SL

2 608 830-020 5 2.29 1.08 SL2 1∕2 608 830-025 5 3.33 1.51 SL

3 608 830-030 5 3.53 1.65 SL4 608 830-040 5 3.76 1.75 SL

121

Reducing Coupling (FPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

T1(inch)

Design

3∕8 x 1∕4 608 830-052 50 1.29 0.60 0.59 HS1∕2 x 1∕4 608 830-072 50 1.44 0.75 0.59 HS1∕2 x 3∕8 608 830-073 50 1.46 0.74 0.60 HS3∕4 x 1∕2 608 830-101 25 1.68 0.78 0.78 HS1 x 1∕2 608 830-130 25 1.84 0.98 0.77 HS1 x 3∕4 608 830-131 25 1.88 0.98 0.80 HS

1 1∕4 x 3∕4 608 830-167 25 1.90 1.00 0.79 HS1 1∕2 x 1 608 830-211 20 2.06 1.02 0.95 HS2 x 1 1∕2 608 830-251 10 2.18 1.05 1.02 HS

Female Adapter (S x FPT) Schedule 80 Harvel® PVC

Size(inch)


HL(inch)

L(inch)

T(inch)

Design

1∕4 608 835-002 50 0.75 1.43 0.58 HS3∕8 608 835-003 50 0.75 1.56 0.62 HS1∕2 608 835-005 25 0.91 1.80 0.75 HS3∕4 608 835-007 25 0.95 1.96 0.79 HS1 608 835-010 25 1.11 2.27 0.98 HS

1 1∕4 608 835-012 10 1.18 2.44 1.02 HS1 1∕2 608 835-015 10 1.19 2.59 1.03 HS

2 608 835-020 5 1.25 2.76 1.06 HS2 1∕2 608 835-025 5 1.77 3.53 1.51 HS

3 608 835-030 5 1.91 3.80 1.65 HS4 608 835-040 5 2.02 4.29 1.74 HS6 608 835-060 2 3.27 6.37 2.37 SL8 608 835-080 2 4.35 8.36 2.35 HS

10 602 835-100 2 5.68 10.78 2.68 HS12 A33 835-120N 1 6.00 11.13 2.13 FAB

Male Adapter (S x MPT) Schedule 80 Harvel® PVC

Size(inch)


HL(inch)

L(inch)

Design

1∕2 608 836-005 50 0.94 1.85 SL3∕4 608 836-007 25 1.05 2.03 HS1 608 836-010 25 1.22 2.38 HS

1 1∕4 608 836-012 15 1.28 2.56 HS1 1∕2 608 836-015 10 1.30 2.69 HS

2 608 836-020 5 1.32 2.83 HS2 1∕2 608 836-025 5 1.87 3.70 HS

3 608 836-030 5 1.99 3.90 HS4 608 836-040 5 2.15 4.40 HS6 A33 836-060N 1 3.25 6.25 FAB8 A33 836-080N 1 3.50 7.50 FAB

10 A33 836-100N 1 4.18 9.18 FAB12 A33 836-120N 1 4.63 10.63 FAB

121

122


Flush Style Reducer Bushing (SPG x S) Schedule 80 Harvel® PVC

Size(inch)


HL(inch)

L(inch)

Design

1∕2 x 1∕4 608 837-072 50 0.47 1.15 FLUSH1∕2 x 3∕8 608 837-073 50 0.33 1.09 FLUSH3∕4 x 1∕2 608 837-101 50 0.42 1.30 FLUSH1 x 1∕2 608 837-130 50 0.55 1.44 FLUSH1 x 3∕4 608 837-131 50 0.41 1.43 FLUSH

1 1∕4 x 1∕2 608 837-166 25 0.66 1.55 FLUSH1 1∕4 x 3∕4 608 837-167 25 0.56 1.57 FLUSH1 1∕4 x 1 608 837-168 25 0.44 1.59 FLUSH1 1∕2 x 1∕2 608 837-209 25 0.78 1.69 FLUSH1 1∕2 x 3∕4 608 837-210 25 0.67 1.68 FLUSH1 1∕2 x 1 608 837-211 25 0.55 1.69 FLUSH

1 1∕2 x 1 1∕4 608 837-212 25 0.44 1.72 FLUSH2 x 1∕2 608 837-247 10 0.91 1.81 FLUSH2 x 3∕4 608 837-248 10 0.79 1.82 FLUSH2 x 1 608 837-249 10 0.68 1.83 FLUSH

2 x 1 1∕4 608 837-250 10 0.54 1.81 FLUSH2 x 1 1∕2 608 837-251 10 0.40 1.81 FLUSH

2 1∕2 x 1 1∕2 608 837-291 5 0.79 2.31 FLUSH2 1∕2 x 2 608 837-292 5 0.47 2.10 FLUSH

3 x 1 608 837-335 5 1.27 2.42 FLUSH3 x 1 1∕4 608 837-336FB 5 1.43 2.71 BUSH3 x 1 1∕2 608 837-337 5 0.89 2.43 FLUSH

3 x 2 608 837-338 5 0.86 2.42 FLUSH3 x 2 1∕2 608 837-339 5 0.38 2.27 FLUSH

4 x 2 608 837-420 5 1.14 2.70 FLUSH4 x 3 608 837-422 5 0.77 2.74 FLUSH6 x 3 608 837-530 2 1.74 3.65 FLUSH6 x 4 608 837-532 2 1.42 3.67 FLUSH8 x 6 608 837-585 2 1.69 4.66 FLUSH

10 x 4 602 837-623FB 1 4.01 6.26 BUSH10 x 6 602 837-626 1 2.59 5.69 FLUSH10 x 8 602 837-628 1 1.62 5.72 FLUSH12 x 6 602 837-666FB 1 4.26 7.35 BUSH12 x 8 602 837-668 1 2.66 6.76 FLUSH

12 x 10 602 837-670 1 1.66 6.77 FLUSH14 x 4 A33 837-696N 1 5.50 7.50 FAB14 x 6 A33 837-698N 1 4.50 7.50 FAB14 x 8 A33 837-700N 1 3.50 7.50 FAB

14 x 10 A33 837-702N 1 2.50 7.50 FAB14 x 12 A33 837-704N 1 1.50 7.50 FAB







122

123


Flush Style Reducer Bushing (SPG x S) Schedule 80 Harvel® PVC

Size(inch)


HL(inch)

L(inch)

Design

1∕2 x 1∕4 608 837-072 50 0.47 1.15 FLUSH1∕2 x 3∕8 608 837-073 50 0.33 1.09 FLUSH3∕4 x 1∕2 608 837-101 50 0.42 1.30 FLUSH1 x 1∕2 608 837-130 50 0.55 1.44 FLUSH1 x 3∕4 608 837-131 50 0.41 1.43 FLUSH



2 x 1 1∕4 608 837-250 10 0.54 1.81 FLUSH2 x 1 1∕2 608 837-251 10 0.40 1.81 FLUSH

2 1∕2 x 1 1∕2 608 837-291 5 0.79 2.31 FLUSH2 1∕2 x 2 608 837-292 5 0.47 2.10 FLUSH

3 x 1 608 837-335 5 1.27 2.42 FLUSH3 x 1 1∕4 608 837-336FB 5 1.43 2.71 BUSH3 x 1 1∕2 608 837-337 5 0.89 2.43 FLUSH

3 x 2 608 837-338 5 0.86 2.42 FLUSH3 x 2 1∕2 608 837-339 5 0.38 2.27 FLUSH

4 x 2 608 837-420 5 1.14 2.70 FLUSH4 x 3 608 837-422 5 0.77 2.74 FLUSH6 x 3 608 837-530 2 1.74 3.65 FLUSH6 x 4 608 837-532 2 1.42 3.67 FLUSH8 x 6 608 837-585 2 1.69 4.66 FLUSH

10 x 4 602 837-623FB 1 4.01 6.26 BUSH10 x 6 602 837-626 1 2.59 5.69 FLUSH10 x 8 602 837-628 1 1.62 5.72 FLUSH12 x 6 602 837-666FB 1 4.26 7.35 BUSH12 x 8 602 837-668 1 2.66 6.76 FLUSH

12 x 10 602 837-670 1 1.66 6.77 FLUSH14 x 4 A33 837-696N 1 5.50 7.50 FAB14 x 6 A33 837-698N 1 4.50 7.50 FAB14 x 8 A33 837-700N 1 3.50 7.50 FAB

14 x 10 A33 837-702N 1 2.50 7.50 FAB14 x 12 A33 837-704N 1 1.50 7.50 FAB







123

Size(inch)


HL(inch)

L(inch)

Design



Flush Style Reducer Bushing (SPG x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

Design

3∕8 x 1∕4 608 838-052E 50 1.59 0.60 Extended1∕2 x 1∕4 608 838-072 50 1.14 0.61 FLUSH1∕2 x 3∕8 608 838-073 50 1.21 0.60 FLUSH3∕4 x 1∕4 608 838-098 50 1.13 0.61 FLUSH3∕4 x 1∕2 608 838-101 50 1.28 0.77 FLUSH1 x 1∕2 608 838-130 50 1.42 0.76 FLUSH1 x 3∕4 608 838-131 50 1.41 0.81 FLUSH



2 x 1 1∕4 608 838-250 10 1.81 1.02 FLUSH2 x 1 1∕2 608 838-251 10 1.88 1.04 FLUSH

2 1∕2 x 1 1∕2 608 838-291 5 2.24 1.07 FLUSH2 1∕2 x 2 608 838-292 5 2.12 1.10 FLUSH

3 x 2 608 838-338 5 2.42 1.07 FLUSH3 x 2 1∕2 608 838-339 5 2.25 1.61 FLUSH

4 x 2 608 838-420 5 2.71 1.10 FLUSH4 x 3 608 838-422 5 2.75 1.62 FLUSH

123

124124

Flush Style Reducer Bushing (MPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

Style

3∕8 x 1∕4 608 839-052 50 0.80 0.60 FLUSH1∕2 x 1∕4 608 839-072 50 0.95 0.60 FLUSH1∕2 x 3∕8 608 839-073 50 0.96 0.61 FLUSH3∕4 x 1∕4 608 839-098 50 1.01 0.61 FLUSH3∕4 x 3∕8 608 839-099 50 1.02 0.61 FLUSH3∕4 x 1∕2 608 839-101 50 1.08 0.75 FLUSH1 x 1∕4 608 839-128 25 1.23 0.58 FLUSH1 x 1∕2 608 839-130 25 1.24 0.76 FLUSH1 x 3∕4 608 839-131 25 1.28 0.80 FLUSH

1 1∕4 x 1∕2 608 839-166 25 1.29 0.76 FLUSH1 1∕4 x 3∕4 608 839-167 25 1.29 0.79 FLUSH1 1∕4 x 1 608 839-168 25 1.30 1.00 FLUSH1 1∕2 x 3∕4 608 839-210 25 1.33 0.78 FLUSH1 1∕2 x 1 608 839-211 25 1.34 0.98 FLUSH


2 x 1 1∕4 608 839-250 10 1.43 1.01 FLUSH2 x 1 1∕2 608 839-251 10 1.35 1.02 FLUSH

3 x 2 608 839-338 5 2.02 1.09 FLUSH4 x 2 608 839-420 5 2.07 1.10 FLUSH4 x 3 608 839-422 5 2.06 1.60 FLUSH

Cap (S) Schedule 80 Harvel® PVC

Size(inch)


W(inch)

Design

1∕4 608 847-002 50 0.96 HS3∕8 608 847-003 50 1.11 HS1∕2 608 847-005 50 1.30 HS3∕4 608 847-007 50 1.46 HS1 608 847-010 25 1.66 HS

1 1∕4 608 847-012 15 1.89 HS1 1∕2 608 847-015 10 2.08 HS

2 608 847-020 5 2.32 HS2 1∕2 608 847-025 5 2.61 HS

3 608 847-030 5 3.06 HS4 608 847-040 5 3.69 HS6 608 847-060 2 4.86 HS8 608 847-080 2 6.25 SL

10 602 847-100 1 7.92 SL12 602 847-120 1 9.37 SL14 A33 847-140N 1 5.75 FAB16 A33 847-160N 1 7.00 FAB18 A33 847-180N 1 8.25 FAB20 A33 847-200N 1 8.75 FAB24 A33 847-240N 1 10.25 FAB

124

125124

Flush Style Reducer Bushing (MPT x FPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

T(inch)

Style

3∕8 x 1∕4 608 839-052 50 0.80 0.60 FLUSH1∕2 x 1∕4 608 839-072 50 0.95 0.60 FLUSH1∕2 x 3∕8 608 839-073 50 0.96 0.61 FLUSH3∕4 x 1∕4 608 839-098 50 1.01 0.61 FLUSH3∕4 x 3∕8 608 839-099 50 1.02 0.61 FLUSH3∕4 x 1∕2 608 839-101 50 1.08 0.75 FLUSH1 x 1∕4 608 839-128 25 1.23 0.58 FLUSH1 x 1∕2 608 839-130 25 1.24 0.76 FLUSH1 x 3∕4 608 839-131 25 1.28 0.80 FLUSH

1 1∕4 x 1∕2 608 839-166 25 1.29 0.76 FLUSH1 1∕4 x 3∕4 608 839-167 25 1.29 0.79 FLUSH1 1∕4 x 1 608 839-168 25 1.30 1.00 FLUSH1 1∕2 x 3∕4 608 839-210 25 1.33 0.78 FLUSH1 1∕2 x 1 608 839-211 25 1.34 0.98 FLUSH


2 x 1 1∕4 608 839-250 10 1.43 1.01 FLUSH2 x 1 1∕2 608 839-251 10 1.35 1.02 FLUSH

3 x 2 608 839-338 5 2.02 1.09 FLUSH4 x 2 608 839-420 5 2.07 1.10 FLUSH4 x 3 608 839-422 5 2.06 1.60 FLUSH

Cap (S) Schedule 80 Harvel® PVC

Size(inch)


W(inch)

Design

1∕4 608 847-002 50 0.96 HS3∕8 608 847-003 50 1.11 HS1∕2 608 847-005 50 1.30 HS3∕4 608 847-007 50 1.46 HS1 608 847-010 25 1.66 HS

1 1∕4 608 847-012 15 1.89 HS1 1∕2 608 847-015 10 2.08 HS

2 608 847-020 5 2.32 HS2 1∕2 608 847-025 5 2.61 HS

3 608 847-030 5 3.06 HS4 608 847-040 5 3.69 HS6 608 847-060 2 4.86 HS8 608 847-080 2 6.25 SL

10 602 847-100 1 7.92 SL12 602 847-120 1 9.37 SL14 A33 847-140N 1 5.75 FAB16 A33 847-160N 1 7.00 FAB18 A33 847-180N 1 8.25 FAB20 A33 847-200N 1 8.75 FAB24 A33 847-240N 1 10.25 FAB

125

Cap (FPT) Schedule 80 Harvel® PVC

Size(inch)


W(inch)

T(inch)

Design

1∕4 608 848-002 50 0.93 0.54 HS3∕8 608 848-003 50 0.94 0.62 HS1∕2 608 848-005 50 1.14 0.74 HS3∕4 608 848-007 25 1.25 0.80 HS1 608 848-010 25 1.51 0.97 HS

1 1∕4 608 848-012 15 1.59 1.00 HS1 1∕2 608 848-015 10 1.70 1.01 HS

2 608 848-020 5 1.82 1.06 HS2 1∕2 608 848-025 5 2.61 1.45 HS

3 608 848-030 5 2.80 1.83 HS4 608 848-040 5 3.16 1.80 HS

Plug (SPG) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

R(inch)

1∕2 608 849-005 50 1.08 0.183∕4 608 849-007 50 1.25 0.221 608 849-010 25 1.41 0.25

1 1∕2 608 849-015 20 1.72 0.312 608 849-020 10 1.90 0.384 608 849-040 5 2.65 0.39

Plug (MPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

R(inch)

Design

1∕4 608 850-002 50 0.81 0.22 HS3∕8 608 850-003 50 0.83 0.22 HS1∕2 608 850-005 50 0.98 0.22 HS3∕4 608 850-007 50 1.06 0.25 HS1 608 850-010 25 1.24 0.27 HS

1 1∕4 608 850-012 25 1.33 0.31 HS1 1∕2 608 850-015 20 1.38 0.34 HS

2 608 850-020 10 1.47 0.39 HS2 1∕2 608 850-025 10 1.95 0.38 HS

3 608 850-030 5 1.98 0.38 HS4 608 850-040 5 2.16 0.39 HS6 A33 850-060N 1 2.00 0.75 FAB8 A33 850-080N 1 2.00 0.75 FAB

10 A33 850-100N 1 2.00 0.75 FAB12 A33 850-120N 1 2.00 0.75 FAB

125

126126

Flange - One Piece (S) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 150 psi @ 73ºF (10.3 bar @ 22.7ºC)• HC = Honeycomb (Face) Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

N1(inch)

R(inch)

Design

1∕2 608 851-005 5 4 1∕2 2.38 3.50 1.02 0.13 0.39 HC3∕4 608 851-007 5 4 1∕2 2.75 3.89 1.14 0.13 0.45 HC1 608 851-010 5 4 1∕2 3.13 4.28 1.30 0.16 0.52 HC

1 1∕4 608 851-012 5 4 1∕2 3.50 4.64 1.45 0.14 0.59 HC1 1∕2 608 851-015 5 4 1∕2 3.88 5.01 1.54 0.16 0.68 HC

2 608 851-020 5 4 5∕8 4.75 6.01 1.73 0.16 0.69 HC2 1∕2 608 851-025 5 4 5∕8 5.50 7.00 1.99 0.17 0.75 HC

3 608 851-030 5 4 5∕8 6.00 7.51 2.46 0.57 1.10 HC4 608 851-040 5 8 5∕8 7.50 9.04 2.79 0.52 1.19 HC6 608 851-060 2 8 3∕4 9.50 11.13 3.88 0.36 1.38 HC8 608 851-080 2 8 3∕4 11.75 13.54 4.90 0.42 1.45 HC

Flange - One Piece (FPT) Schedule 80 Harvel® PVC



#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

T(inch)

R(inch)

Design

1∕2 608 852-005 5 4 1∕2 2.38 3.51 0.89 0.77 0.39 HC3∕4 608 852-007 5 4 1∕2 2.75 3.89 0.91 0.79 0.45 HC1 608 852-010 5 4 1∕2 3.13 4.28 1.13 1.00 0.53 HC

1 1∕4 608 852-012 5 4 1∕2 3.50 4.62 1.20 1.06 0.58 HC1 1∕2 608 852-015 5 4 1∕2 3.88 4.99 1.19 1.03 0.68 HC

2 608 852-020 5 4 5∕8 4.75 6.02 1.22 1.06 0.70 HC2 1∕2 608 852-025 5 4 5∕8 5.50 7.00 1.72 1.53 0.75 HC

3 608 852-030 5 4 5∕8 6.00 7.50 2.15 1.63 1.15 HC4 608 852-040 5 8 5∕8 7.50 9.00 2.30 1.77 1.23 HC

126

127126

Flange - One Piece (S) Schedule 80 Harvel® PVC



#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

N1(inch)

R(inch)

Design

1∕2 608 851-005 5 4 1∕2 2.38 3.50 1.02 0.13 0.39 HC3∕4 608 851-007 5 4 1∕2 2.75 3.89 1.14 0.13 0.45 HC1 608 851-010 5 4 1∕2 3.13 4.28 1.30 0.16 0.52 HC

1 1∕4 608 851-012 5 4 1∕2 3.50 4.64 1.45 0.14 0.59 HC1 1∕2 608 851-015 5 4 1∕2 3.88 5.01 1.54 0.16 0.68 HC

2 608 851-020 5 4 5∕8 4.75 6.01 1.73 0.16 0.69 HC2 1∕2 608 851-025 5 4 5∕8 5.50 7.00 1.99 0.17 0.75 HC

3 608 851-030 5 4 5∕8 6.00 7.51 2.46 0.57 1.10 HC4 608 851-040 5 8 5∕8 7.50 9.04 2.79 0.52 1.19 HC6 608 851-060 2 8 3∕4 9.50 11.13 3.88 0.36 1.38 HC8 608 851-080 2 8 3∕4 11.75 13.54 4.90 0.42 1.45 HC

Flange - One Piece (FPT) Schedule 80 Harvel® PVC



#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

T(inch)

R(inch)

Design

1∕2 608 852-005 5 4 1∕2 2.38 3.51 0.89 0.77 0.39 HC3∕4 608 852-007 5 4 1∕2 2.75 3.89 0.91 0.79 0.45 HC1 608 852-010 5 4 1∕2 3.13 4.28 1.13 1.00 0.53 HC

1 1∕4 608 852-012 5 4 1∕2 3.50 4.62 1.20 1.06 0.58 HC1 1∕2 608 852-015 5 4 1∕2 3.88 4.99 1.19 1.03 0.68 HC

2 608 852-020 5 4 5∕8 4.75 6.02 1.22 1.06 0.70 HC2 1∕2 608 852-025 5 4 5∕8 5.50 7.00 1.72 1.53 0.75 HC

3 608 852-030 5 4 5∕8 6.00 7.50 2.15 1.63 1.15 HC4 608 852-040 5 8 5∕8 7.50 9.00 2.30 1.77 1.23 HC

127

Flange - Van Stone (S) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 1/2" - 12" pressure rating is 150 psi @ 73°F (10.3 bar @ 22.7°C)• 14" - 24" pressure rating is 100 psi @ 73°F (6.9 bar @ 22.7°C) - Steel Ring• HC = Honeycomb (Face) Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

N1(inch)

R(inch)

ID(inch)

Design

1∕2 608 854-005 5 4 1∕2 2.38 3.53 1.10 0.18 0.57 0.60 HC3∕4 608 854-007 5 4 1∕2 2.75 3.87 1.23 0.18 0.59 0.82 HC1 608 854-010 5 4 1∕2 3.13 4.25 1.38 0.20 0.66 1.03 HC

1 1∕4 608 854-012 5 4 1∕2 3.50 4.62 1.52 0.21 0.69 1.36 HC1 1∕2 608 854-015 5 4 1∕2 3.88 5.01 1.68 0.25 0.75 1.60 HC

2 608 854-020 5 4 5∕8 4.75 6.02 1.84 0.29 0.82 2.06 HC2 1∕2 608 854-025 5 4 5∕8 5.50 7.01 2.15 0.33 0.98 2.49 HC

3 608 854-030 5 4 5∕8 6.00 7.50 2.33 0.39 1.02 3.09 HC4 608 854-040 5 8 5∕8 7.50 8.99 2.75 0.24 1.10 4.06 HC6 608 854-060 2 8 3∕4 9.50 10.98 3.55 0.48 1.25 6.11 HC8 608 854-080 2 8 3∕4 11.75 13.51 4.60 0.51 1.71 8.00 HC

10 602 854-100 2 12 7∕8 14.25 15.97 5.66 0.53 1.73 10.10 HC12 602 854-120 2 12 7∕8 17.00 18.95 6.71 0.57 1.72 11.96 HC14 A33 854-140N 1 12 1 18.75 21.00 11.75 4.75 0.50 12.50 FAB16 A33 854-160N 1 16 1 21.25 23.50 13.50 5.50 0.50 14.31 FAB18 A33 854-180N 1 16 1 1∕8 22.75 25.00 14.50 5.50 0.50 16.13 FAB20 A33 854-200N 1 20 1 1∕8 25.00 27.50 17.25 7.25 0.50 18.00 FAB24 A33 854-240N 1 20 1 1∕4 29.50 32.00 19.50 7.50 0.50 21.56 FAB

Flange - Van Stone (FPT) Schedule 80 Harvel® PVC



#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

T(inch)

R(inch)

ID(inch)

Design

1∕2 608 855-005 5 4 1∕2 2.38 3.53 1.10 0.79 0.57 0.63 HC3∕4 608 855-007 5 4 1∕2 2.75 3.87 1.23 0.82 0.59 0.83 HC1 608 855-010 5 4 1∕2 3.13 4.25 1.39 1.01 0.66 1.06 HC

1 1∕4 608 855-012 5 4 1∕2 3.50 4.62 1.50 1.02 0.69 1.38 HC1 1∕2 608 855-015 5 4 1∕2 3.88 5.01 1.67 1.06 0.75 1.61 HC

2 608 855-020 5 4 5∕8 4.75 6.02 1.82 1.09 0.82 2.08 HC2 1∕2 608 855-025 5 4 5∕8 5.50 7.01 2.13 1.58 0.98 2.50 HC

3 608 855-030 5 4 5∕8 6.00 7.50 2.36 1.71 1.02 3.08 HC4 608 855-040 5 8 5∕8 7.50 8.99 2.78 1.72 1.10 4.09 HC

127

128128

Flange - Van Stone (SPG) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 1/2" - 12" pressure rating is 150 psi @ 73°F (10.3 bar @ 22.7°C)• 14" - 24" pressure rating is 100 psi @ 73°F (6.9 bar @ 22.7°C) - Steel RingHC = Honeycomb (Face)

Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

R(inch)

ID(inch)

Design

1∕2 608 856-005 5 4 1∕2 2.38 3.53 1.72 0.57 0.84 HC3∕4 608 856-007 5 4 1∕2 2.75 3.87 1.85 0.59 1.05 HC1 608 856-010 5 4 1∕2 3.13 4.25 2.10 0.66 1.32 HC

1 1∕4 608 856-012 5 4 1∕2 3.50 4.62 2.28 0.69 1.66 HC1 1∕2 608 856-015 5 4 1∕2 3.88 5.01 2.48 0.75 1.90 HC

2 608 856-020 5 4 5∕8 4.75 6.02 2.80 0.82 2.38 HC2 1∕2 608 856-025 5 4 5∕8 5.50 7.01 3.27 0.98 2.86 HC

3 608 856-030 5 4 5∕8 6.00 7.50 3.60 1.02 3.49 HC4 608 856-040 5 8 5∕8 7.50 8.99 4.10 1.10 4.49 HC6 608 856-060 2 8 3∕4 9.50 10.98 5.10 1.25 6.60 HC8 608 856-080 1 8 3∕4 11.75 13.51 6.88 1.71 8.62 HC

10 602 856-100 1 12 7∕8 14.25 15.97 8.30 1.73 10.70 HC12 602 856-120 1 12 7∕8 17.00 18.95 9.55 1.72 12.69 HC14 A33 856-140N 1 12 1 18.75 21.00 13.00 0.50 11.41 FAB16 A33 856-160N 1 16 1 21.25 23.50 14.00 0.50 13.08 FAB18 A33 856-180N 1 16 1 1∕8 22.75 25.00 16.00 0.50 14.76 FAB20 A33 856-200N 1 20 1 1∕8 25.00 27.50 18.00 0.50 16.43 FAB24 A33 856-240N 1 20 1 1∕4 29.50 32.00 20.00 0.50 19.79 FAB

Flange (Blind) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 1/2" - 8" 150 psi @ 73°F (10.3 bar @ 22.7°C)• 10" - 24" 50 psi @73°F (3.5 bar @ 22.7°C)• HC = Honeycomb (Face) Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

R(inch)

Design

1∕2 608 853-005 5 4 1∕2 2.38 3.51 0.48 0.39 HC3∕4 608 853-007 5 4 1∕2 2.75 3.90 0.55 0.45 HC1 608 853-010 5 4 1∕2 3.13 4.29 0.66 0.53 HC

1 1∕4 608 853-012 5 4 1∕2 3.50 4.62 0.73 0.59 HC1 1∕2 608 853-015 5 4 1∕2 3.88 5.01 0.81 0.68 HC

2 608 853-020 5 4 5∕8 4.75 6.02 0.90 0.70 HC2 1∕2 608 853-025 5 4 5∕8 5.50 7.00 0.97 0.76 HC

3 608 853-030 5 4 5∕8 6.00 7.45 1.03 1.03 HC4 608 853-040 5 8 5∕8 7.50 8.96 1.14 1.14 HC6 608 853-060 2 8 3∕4 9.50 10.95 1.51 1.27 HC8 608 853-080 2 8 3∕4 11.75 13.51 1.62 1.45 HC

10 A33 853-100N 1 12 7∕8 14.25 16.00 1.00 1.00 SOLID12 A33 853-120N 1 12 7∕8 17.00 19.00 1.00 1.00 SOLID14 A33 853-140N 1 12 1 18.75 21.00 1.00 1.00 SOLID16 A33 853-160N 1 16 1 21.25 23.50 1.00 1.00 SOLID18 A33 853-180N 1 16 1 1∕8 22.75 25.00 1.00 1.00 SOLID20 A33 853-200N 1 20 1 1∕8 25.00 27.50 1.00 1.00 SOLID24 A33 853-240N 1 20 1 1∕4 29.50 32.00 1.00 1.00 SOLID

128

129128

Flange - Van Stone (SPG) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 1/2" - 12" pressure rating is 150 psi @ 73°F (10.3 bar @ 22.7°C)• 14" - 24" pressure rating is 100 psi @ 73°F (6.9 bar @ 22.7°C) - Steel RingHC = Honeycomb (Face)

Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

R(inch)

ID(inch)

Design

1∕2 608 856-005 5 4 1∕2 2.38 3.53 1.72 0.57 0.84 HC3∕4 608 856-007 5 4 1∕2 2.75 3.87 1.85 0.59 1.05 HC1 608 856-010 5 4 1∕2 3.13 4.25 2.10 0.66 1.32 HC

1 1∕4 608 856-012 5 4 1∕2 3.50 4.62 2.28 0.69 1.66 HC1 1∕2 608 856-015 5 4 1∕2 3.88 5.01 2.48 0.75 1.90 HC

2 608 856-020 5 4 5∕8 4.75 6.02 2.80 0.82 2.38 HC2 1∕2 608 856-025 5 4 5∕8 5.50 7.01 3.27 0.98 2.86 HC

3 608 856-030 5 4 5∕8 6.00 7.50 3.60 1.02 3.49 HC4 608 856-040 5 8 5∕8 7.50 8.99 4.10 1.10 4.49 HC6 608 856-060 2 8 3∕4 9.50 10.98 5.10 1.25 6.60 HC8 608 856-080 1 8 3∕4 11.75 13.51 6.88 1.71 8.62 HC

10 602 856-100 1 12 7∕8 14.25 15.97 8.30 1.73 10.70 HC12 602 856-120 1 12 7∕8 17.00 18.95 9.55 1.72 12.69 HC14 A33 856-140N 1 12 1 18.75 21.00 13.00 0.50 11.41 FAB16 A33 856-160N 1 16 1 21.25 23.50 14.00 0.50 13.08 FAB18 A33 856-180N 1 16 1 1∕8 22.75 25.00 16.00 0.50 14.76 FAB20 A33 856-200N 1 20 1 1∕8 25.00 27.50 18.00 0.50 16.43 FAB24 A33 856-240N 1 20 1 1∕4 29.50 32.00 20.00 0.50 19.79 FAB

Flange (Blind) Schedule 80 Harvel® PVC

• ANSI 150 Class according to ANSI B16.5• 1/2" - 8" 150 psi @ 73°F (10.3 bar @ 22.7°C)• 10" - 24" 50 psi @73°F (3.5 bar @ 22.7°C)• HC = Honeycomb (Face) Size(inch)


#holes

BoltDia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

R(inch)

Design

1∕2 608 853-005 5 4 1∕2 2.38 3.51 0.48 0.39 HC3∕4 608 853-007 5 4 1∕2 2.75 3.90 0.55 0.45 HC1 608 853-010 5 4 1∕2 3.13 4.29 0.66 0.53 HC

1 1∕4 608 853-012 5 4 1∕2 3.50 4.62 0.73 0.59 HC1 1∕2 608 853-015 5 4 1∕2 3.88 5.01 0.81 0.68 HC

2 608 853-020 5 4 5∕8 4.75 6.02 0.90 0.70 HC2 1∕2 608 853-025 5 4 5∕8 5.50 7.00 0.97 0.76 HC

3 608 853-030 5 4 5∕8 6.00 7.45 1.03 1.03 HC4 608 853-040 5 8 5∕8 7.50 8.96 1.14 1.14 HC6 608 853-060 2 8 3∕4 9.50 10.95 1.51 1.27 HC8 608 853-080 2 8 3∕4 11.75 13.51 1.62 1.45 HC

10 A33 853-100N 1 12 7∕8 14.25 16.00 1.00 1.00 SOLID12 A33 853-120N 1 12 7∕8 17.00 19.00 1.00 1.00 SOLID14 A33 853-140N 1 12 1 18.75 21.00 1.00 1.00 SOLID16 A33 853-160N 1 16 1 21.25 23.50 1.00 1.00 SOLID18 A33 853-180N 1 16 1 1∕8 22.75 25.00 1.00 1.00 SOLID20 A33 853-200N 1 20 1 1∕8 25.00 27.50 1.00 1.00 SOLID24 A33 853-240N 1 20 1 1∕4 29.50 32.00 1.00 1.00 SOLID

129

Flange - Van Stone 300 (S) Schedule 80 Harvel® PVC

• ANSI 300 Class according to ANSI B16.5• 150 psi @ 73ºF (10.3 bar @ 22.7ºC) Size(inch)


#holes

Bolt Dia.(inch)

bolt cir.dia.

(inch)

D(inch)

L(inch)

N1(inch)

R(inch)

Design

1∕2 608 854-005-300 5 4 1∕2 2.63 3.75 1.03 0.11 0.57 FAB3∕4 608 854-007-300 5 4 5∕8 3.25 4.63 1.15 0.13 0.59 FAB1 608 854-010-300 5 4 5∕8 3.50 4.88 1.38 0.11 0.66 FAB

1 1∕4 608 854-012-300 5 4 5∕8 3.88 5.25 1.45 0.14 0.69 FAB1 1∕2 608 854-015-300 5 4 3∕4 4.50 6.13 1.59 0.15 0.75 FAB

2 608 854-020-300 5 8 5∕8 5.00 6.50 1.76 0.20 0.82 FAB2 1∕2 608 854-025-300 5 8 3∕4 5.88 7.50 2.05 0.22 0.98 FAB

3 608 854-030-300 5 8 3∕4 6.63 8.25 2.25 0.30 1.02 FAB4 608 854-040-300 5 8 3∕4 7.88 10.00 2.65 0.34 1.10 FAB6 608 854-060-300 2 12 3∕4 10.63 12.50 3.45 0.35 1.25 FAB8 608 854-080-300 2 12 7∕8 13.00 15.00 4.50 0.40 1.71 FAB

10 602 854-100-300 2 16 1 15.25 17.50 5.63 0.50 1.73 FAB12 602 854-120-300 2 16 1 1∕8 17.75 20.50 6.69 0.56 1.72 FAB

Union Type 375 (S x S) Schedule 80 Harvel® PVC

235 psi @ 73°F (16.2 bar @ 22.7°C)

Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

N(inch)

1∕2 608 897-375-005 857-375-005 5 2.56 0.783∕4 608 897-375-007 857-375-007 5 2.80 0.761 608 897-375-010 857-375-010 5 3.22 0.89

1 1∕4 608 897-375-012 857-375-012 5 3.56 0.991 1∕2 608 897-375-015 857-375-015 5 3.76 0.92

2 608 897-375-020 857-375-020 2 4.18 1.11

129

130130

Union (S x S) Schedule 80 Harvel® PVC

150 psi @ 73°F (10.3 bar @ 22.7°C)

Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

N(inch)

3 608 897-030 857-030 1 4.74 0.964 608 897-040 857-040 1 5.62 1.11

Union Type 375 (FPT X FPT) Schedule 80 Harvel® PVC

• 235 psi @ 73°F (16.2 bar @ 22.7°C) Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

T(inch)

1∕2 608 898-375-005 858-375-005 5 2.06 0.753∕4 608 898-375-007 858-375-007 5 2.11 0.791 608 898-375-010 858-375-010 5 2.60 1.01

1 1∕4 608 898-375-012 858-375-012 5 2.80 1.061 1∕2 608 898-375-015 858-375-015 5 2.76 1.06

2 608 898-375-020 858-375-020 2 2.93 1.09

130

131130

Union (S x S) Schedule 80 Harvel® PVC

150 psi @ 73°F (10.3 bar @ 22.7°C)

Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

N(inch)

3 608 897-030 857-030 1 4.74 0.964 608 897-040 857-040 1 5.62 1.11

Union Type 375 (FPT X FPT) Schedule 80 Harvel® PVC

• 235 psi @ 73°F (16.2 bar @ 22.7°C) Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

T(inch)

1∕2 608 898-375-005 858-375-005 5 2.06 0.753∕4 608 898-375-007 858-375-007 5 2.11 0.791 608 898-375-010 858-375-010 5 2.60 1.01

1 1∕4 608 898-375-012 858-375-012 5 2.80 1.061 1∕2 608 898-375-015 858-375-015 5 2.76 1.06

2 608 898-375-020 858-375-020 2 2.93 1.09


Union (FPT X FPT) Schedule 80 Harvel® PVC

• 150 psi @ 73ºF (10.3 bar @ 22.7ºC) Size(inch)

P/L EPDMPart No.

FKMPart No.

PackQty

L(inch)

T(inch)

3 608 898-030 858-030 1 4.75 1.334 608 898-040 858-040 1 5.71 1.78

Nipple (MPT x MPT) Schedule 80 Harvel® PVC

Size(inch)


L(inch)

Design

1/2 x CL 608 861-077 50 1.13 MOLD1/2 x 2 608 861-079 25 2.00 MOLD1/2 x 3 608 861-081 25 3.00 MOLD1/2 x 4 608 861-082 25 4.00 MOLD1/2 x 5 608 861-083 25 5.00 MOLD1/2 x 6 608 861-084 25 6.00 MOLD1/2 x 8 608 861-086 25 8.00 FAB

1/2 x 10 608 861-087 25 10.00 FAB1/2 x 12 608 861-088 25 12.00 FAB3/4 x CL 608 861-104 25 1.38 MOLD

3/4 x 2 608 861-020 25 2.00 MOLD3/4 x 3 608 861-106 25 3.00 MOLD3/4 x 4 608 861-107 25 4.00 MOLD3/4 x 5 608 861-108 25 5.00 MOLD3/4 x 6 608 861-109 25 6.00 MOLD3/4 x 8 608 861-110 25 8.00 FAB

3/4 x 10 608 861-111 25 10.00 FAB3/4 x 12 608 861-112 25 12.00 FAB

1 x CL 608 861-133 25 1.50 MOLD1 x 2 608 861-134 25 2.00 MOLD1 x 3 608 861-135 25 3.00 MOLD1 x 4 608 861-136 25 4.00 MOLD1 x 5 608 861-137 25 5.00 MOLD1 x 6 608 861-138 25 6.00 MOLD1 x 8 608 861-139 25 8.00 FAB

1 x 10 608 861-140 25 10.00 FAB1 x 12 608 861-141 25 12.00 FAB

1 1/4 x CL 608 861-170 25 1.63 MOLD1 1/4 x 2 608 861-171 25 2.00 MOLD1 1/4 x 3 608 861-172 25 3.00 MOLD1 1/4 x 4 608 861-173 25 4.00 MOLD1 1/4 x 5 608 861-174 25 5.00 MOLD

131

132132

Size(inch)


L(inch)

Design

1 1/4 x 6 608 861-175 25 6.00 MOLD1 1/4 x 8 608 861-176 25 8.00 FAB

1 1/4 x 10 608 861-177 25 10.00 FAB1 1/4 x 12 608 861-178 25 12.00 FAB1 1/2 x CL 608 861-213 25 1.75 MOLD

1 1/2 x 2 608 861-214 25 2.00 MOLD1 1/2 x 3 608 861-215 25 3.00 MOLD1 1/2 x 4 608 861-216 25 4.00 MOLD1 1/2 x 5 608 861-217 25 5.00 MOLD1 1/2 x 6 608 861-218 25 6.00 MOLD1 1/2 x 8 608 861-219 25 8.00 FAB

1 1/2 x 10 608 861-220 25 10.00 FAB1 1/2 x 12 608 861-221 25 12.00 FAB

2 x CL 608 861-251 25 2.00 MOLD2 x 2 1/2 608 861-252 25 2.50 MOLD

2 x 3 608 861-253 25 3.00 MOLD2 x 4 608 861-254 25 4.00 MOLD2 x 5 608 861-255 25 5.00 MOLD2 x 6 608 861-256 25 6.00 MOLD2 x 8 608 861-257 25 8.00 FAB

2 x 10 608 861-258 25 10.00 FAB2 x 12 608 861-259 25 12.00 FAB

2 1/2 x CL 608 861-291 10 2.50 FAB2 1/2 x 4 608 861-295 10 4.00 FAB2 1/2 x 3 608 861-292 10 3.00 FAB2 1/2 x 5 608 861-296 10 5.00 FAB2 1/2 x 6 608 861-297 10 6.00 FAB2 1/2 x 8 608 861-298 10 8.00 FAB

2 1/2 x 10 608 861-299 10 10.00 FAB2 1/2 x 12 608 861-300 10 12.00 FAB

3 x CL 608 861-338 10 2.63 FAB3 x 3 608 861-340 10 3.00 FAB3 x 4 608 861-341 10 4.00 FAB3 x 5 608 861-342 10 5.00 FAB3 x 6 608 861-343 10 6.00 FAB3 x 8 608 861-344 10 8.00 FAB

3 x 10 608 861-345 10 10.00 FAB3 x 12 608 861-346 10 12.00 FAB4 x CL 608 861-422 10 2.88 FAB

4 x 4 608 861-423 10 4.00 FAB4 x 5 608 861-425 10 5.00 FAB4 x 6 608 861-426 10 6.00 FAB4 x 8 608 861-427 5 8.00 FAB

4 x 10 608 861-428 5 10.00 FAB4 x 12 608 861-429 5 12.00 FAB

132

133132

Size(inch)


L(inch)

Design

1 1/4 x 6 608 861-175 25 6.00 MOLD1 1/4 x 8 608 861-176 25 8.00 FAB

1 1/4 x 10 608 861-177 25 10.00 FAB1 1/4 x 12 608 861-178 25 12.00 FAB1 1/2 x CL 608 861-213 25 1.75 MOLD

1 1/2 x 2 608 861-214 25 2.00 MOLD1 1/2 x 3 608 861-215 25 3.00 MOLD1 1/2 x 4 608 861-216 25 4.00 MOLD1 1/2 x 5 608 861-217 25 5.00 MOLD1 1/2 x 6 608 861-218 25 6.00 MOLD1 1/2 x 8 608 861-219 25 8.00 FAB

1 1/2 x 10 608 861-220 25 10.00 FAB1 1/2 x 12 608 861-221 25 12.00 FAB

2 x CL 608 861-251 25 2.00 MOLD2 x 2 1/2 608 861-252 25 2.50 MOLD

2 x 3 608 861-253 25 3.00 MOLD2 x 4 608 861-254 25 4.00 MOLD2 x 5 608 861-255 25 5.00 MOLD2 x 6 608 861-256 25 6.00 MOLD2 x 8 608 861-257 25 8.00 FAB

2 x 10 608 861-258 25 10.00 FAB2 x 12 608 861-259 25 12.00 FAB

2 1/2 x CL 608 861-291 10 2.50 FAB2 1/2 x 4 608 861-295 10 4.00 FAB2 1/2 x 3 608 861-292 10 3.00 FAB2 1/2 x 5 608 861-296 10 5.00 FAB2 1/2 x 6 608 861-297 10 6.00 FAB2 1/2 x 8 608 861-298 10 8.00 FAB

2 1/2 x 10 608 861-299 10 10.00 FAB2 1/2 x 12 608 861-300 10 12.00 FAB

3 x CL 608 861-338 10 2.63 FAB3 x 3 608 861-340 10 3.00 FAB3 x 4 608 861-341 10 4.00 FAB3 x 5 608 861-342 10 5.00 FAB3 x 6 608 861-343 10 6.00 FAB3 x 8 608 861-344 10 8.00 FAB

3 x 10 608 861-345 10 10.00 FAB3 x 12 608 861-346 10 12.00 FAB4 x CL 608 861-422 10 2.88 FAB

4 x 4 608 861-423 10 4.00 FAB4 x 5 608 861-425 10 5.00 FAB4 x 6 608 861-426 10 6.00 FAB4 x 8 608 861-427 5 8.00 FAB

4 x 10 608 861-428 5 10.00 FAB4 x 12 608 861-429 5 12.00 FAB

133

Schedule 80 PVC Low Pressure Fittings

Tee Low Pressure (SxSxS) Schedule 80 Harvel® PVC


P/L Part No. Pack Qty H(inch)

G(inch)

10 B11 H801100LP 1 10.83 5.7712 B11 H801120LP 1 13.38 6.91

90° Ell Low Pressure (S x S) Schedule 80 Harvel® PVC



G(inch)

10 B11 H806100LP 1 10.75 5.7512 B11 H806120LP 1 12.96 6.91

133

134134




J(inch)

10 B11 H817100LP 1 7.50 2.5012 B11 H817120LP 1 9.00 3.00

Coupling Low Pressure (S x S) Schedule 80 Harvel® PVC


P/L Part No. Pack Qty L(inch)

N(inch)

10 B11 H829100LP 1 10.81 0.7512 B11 H829120LP 1 12.81 0.75

134

135134




J(inch)

10 B11 H817100LP 1 7.50 2.5012 B11 H817120LP 1 9.00 3.00

Coupling Low Pressure (S x S) Schedule 80 Harvel® PVC


P/L Part No. Pack Qty L(inch)

N(inch)

10 B11 H829100LP 1 10.81 0.7512 B11 H829120LP 1 12.81 0.75


Schedule 80 PVC DWV Fittings

1/4 Bend Short Sweep (SxS) Schedule 80 Harvel® PVC

Size(inch)

P/L Part No. Pack Qty G(inch)

1 1/2 608 806-015SS 4 1.752 608 806-020SS 4 2.313 608 806-030SS 1 3.064 608 806-040SS 1 3.88

1/4 Bend Long Sweep (SxS) - (FAB) Schedule 80 Harvel® PVC

Size(inch)


1 1/2 A33 806-015LSN 4 4.132 A33 806-020LSN 4 4.753 A33 806-030LSN 1 7.004 A33 806-040LSN 1 9.00

45° Wye (S x S x S) Schedule 80 Harvel® PVC

1-1/2" - 2" 235 psi @ 72°F (16.2 bar @ 22.7°C)3" - 6" 150 psi @ 72°F (10.3 bar @ 22.7°C)8" - 24" 100 psi @ 72°F (6.9 bar @ 22.7°C)

Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

1 1∕2 608 870-015 20 2.79 1.20 2.60 4.18 6.80 4.02 SL2 608 870-020 10 3.56 1.36 2.87 5.07 7.99 4.97 SL

2 1∕2 H02 870-025S 1 3.97 0.84 2.59 5.72 8.31 3.97 SL3 608 870-030 4 4.91 1.82 3.73 6.83 10.45 6.62 SL4 608 870-040 4 6.26 2.06 4.41 8.61 12.94 8.24 SL6 608 870-060 2 8.38 1.85 4.90 11.44 16.50 10.39 HS8 608 870-080 1 11.09 1.90 5.92 15.11 21.35 13.30 HS

10 A33 875-100N 1 19.75 5.50 11.25 24.75 31.75 21.75 FAB12 A33 875-120N 1 22.63 6.50 12.50 28.63 37.50 25.50 FAB14 A33 875-140N 1 25.75 7.00 14.00 32.75 41.75 27.75 FAB

135

136


Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

16 A33 875-160N 1 28.88 7.75 16.00 36.88 47.25 31.25 FAB18 A33 875-180N 1 32.50 8.50 17.50 41.50 53.00 35.00 FAB20 A33 875-200N 1 35.50 9.50 19.50 45.50 58.75 38.75 FAB24 A33 875-240N 1 42.00 11.00 23.00 54.00 70.00 46.00 FAB

Reducing 45° Wye (S x S x S) Schedule 80 Harvel® PVC

2" 235 psi @ 72°F (16.2 bar @ 22.7° C)3" - 6" 150 psi @ 72°F (10.3 bar @ 22.7°C)8" - 24" 100 psi @ 72°F (6.9 bar @ 22.7°C)

Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

2 x 1 1∕2 608 870-251FB 10 3.96 1.36 2.87 5.37 7.99 4.97 BUSH3 x 1 1∕2 608 870-337FB 4 5.80 1.82 3.73 7.34 10.45 6.62 BUSH

3 x 2 608 870-338FB 4 5.77 1.82 3.73 7.33 10.45 6.62 BUSH4 x 2 608 870-420FB 4 7.40 2.06 4.41 7.40 12.94 8.24 BUSH4 x 3 608 870-422FB 4 7.03 2.06 4.41 9.00 12.94 8.24 BUSH6 x 2 608 870-528FB 2 8.24 1.87 4.91 8.24 16.49 10.42 BUSH6 x 3 608 870-530FB 2 7.88 1.87 4.91 9.84 16.49 10.42 BUSH6 x 4 608 870-532 2 7.14 1.87 4.91 9.36 16.49 10.42 HS8 x 3 608 870-580FB 1 10.23 0.41 4.43 12.20 15.98 7.95 BUSH8 x 4 608 870-582 1 9.46 0.41 4.43 11.73 15.98 7.95 HS8 x 6 608 870-585FB 1 12.78 1.90 5.92 15.76 21.35 13.30 BUSH

10 x 4 A33 875-623N 1 14.00 1.25 6.25 16.00 23.00 13.00 FAB10 x 6 A33 875-626N 1 16.13 2.75 7.50 19.13 26.00 16.00 FAB10 x 8 A33 875-628N 1 17.50 4.00 9.25 21.50 28.00 18.75 FAB12 x 4 A33 875-663N 1 15.50 0.50 6.00 17.50 25.75 13.75 FAB12 x 6 A33 875-666N 1 16.68 2.00 8.00 20.50 28.68 16.68 FAB12 x 8 A33 875-668N 1 19.00 3.50 9.50 23.00 31.50 19.50 FAB

12 x 10 A33 875-670N 1 21.25 5.00 11.00 26.25 34.50 22.50 FAB14 x 4 A33 875-696N 1 16.25 0.25 7.25 18.25 28.25 14.25 FAB14 x 6 A33 875-698N 1 18.50 1.75 8.63 21.50 31.25 17.25 FAB14 x 8 A33 875-700N 1 19.75 3.00 10.00 23.75 34.00 20.00 FAB

14 x 10 A33 875-702N 1 22.00 4.50 11.50 27.00 37.00 23.00 FAB14 x 12 A33 875-704N 1 23.50 6.00 13.00 29.50 39.75 25.75 FAB

16 x 4 A33 875-730N 1 17.75 -0.75 7.50 19.75 31.00 15.00 FAB16 x 6 A33 875-732N 1 19.88 1.00 9.00 22.88 34.00 18.00 FAB16 x 8 A33 875-734N 1 21.25 2.50 10.25 25.25 36.75 20.75 FAB

16 x 10 A33 875-736N 1 23.50 4.00 12.00 28.50 39.75 23.75 FAB16 x 12 A33 875-738N 1 25.00 5.50 14.25 31.00 42.75 26.75 FAB16 x 14 A33 875-740N 1 27.25 6.25 14.25 34.25 44.50 28.50 FAB



20 x 4 A33 875-814N 1 20.50 -1.75 8.50 22.50 36.75 16.75 FAB20 x 6 A33 875-816N 1 22.75 -0.25 10.00 25.75 39.75 19.75 FAB20 x 8 A33 875-818N 1 24.25 1.50 11.50 28.25 42.75 22.75 FAB

20 x 10 A33 875-820N 1 26.50 3.00 13.00 31.50 45.75 25.75 FAB20 x 12 A33 875-822N 1 28.00 4.25 14.25 34.00 48.50 28.50 FAB20 x 14 A33 875-824N 1 30.25 5.25 15.00 37.25 50.25 30.25 FAB20 x 16 A33 875-826N 1 31.75 6.50 16.50 39.75 53.00 33.00 FAB20 x 18 A33 875-828N 1 34.00 8.00 18.00 43.00 56.00 36.00 FAB

24 x 4 A33 875-904N 1 23.25 -3.00 9.25 25.25 42.50 18.50 FAB24 x 6 A33 875-906N 1 25.50 -1.50 10.75 28.50 45.50 21.54 FAB

136

137


Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

16 A33 875-160N 1 28.88 7.75 16.00 36.88 47.25 31.25 FAB18 A33 875-180N 1 32.50 8.50 17.50 41.50 53.00 35.00 FAB20 A33 875-200N 1 35.50 9.50 19.50 45.50 58.75 38.75 FAB24 A33 875-240N 1 42.00 11.00 23.00 54.00 70.00 46.00 FAB

Reducing 45° Wye (S x S x S) Schedule 80 Harvel® PVC

2" 235 psi @ 72°F (16.2 bar @ 22.7° C)3" - 6" 150 psi @ 72°F (10.3 bar @ 22.7°C)8" - 24" 100 psi @ 72°F (6.9 bar @ 22.7°C)

Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

2 x 1 1∕2 608 870-251FB 10 3.96 1.36 2.87 5.37 7.99 4.97 BUSH3 x 1 1∕2 608 870-337FB 4 5.80 1.82 3.73 7.34 10.45 6.62 BUSH

3 x 2 608 870-338FB 4 5.77 1.82 3.73 7.33 10.45 6.62 BUSH4 x 2 608 870-420FB 4 7.40 2.06 4.41 7.40 12.94 8.24 BUSH4 x 3 608 870-422FB 4 7.03 2.06 4.41 9.00 12.94 8.24 BUSH6 x 2 608 870-528FB 2 8.24 1.87 4.91 8.24 16.49 10.42 BUSH6 x 3 608 870-530FB 2 7.88 1.87 4.91 9.84 16.49 10.42 BUSH6 x 4 608 870-532 2 7.14 1.87 4.91 9.36 16.49 10.42 HS8 x 3 608 870-580FB 1 10.23 0.41 4.43 12.20 15.98 7.95 BUSH8 x 4 608 870-582 1 9.46 0.41 4.43 11.73 15.98 7.95 HS8 x 6 608 870-585FB 1 12.78 1.90 5.92 15.76 21.35 13.30 BUSH

10 x 4 A33 875-623N 1 14.00 1.25 6.25 16.00 23.00 13.00 FAB10 x 6 A33 875-626N 1 16.13 2.75 7.50 19.13 26.00 16.00 FAB10 x 8 A33 875-628N 1 17.50 4.00 9.25 21.50 28.00 18.75 FAB12 x 4 A33 875-663N 1 15.50 0.50 6.00 17.50 25.75 13.75 FAB12 x 6 A33 875-666N 1 16.68 2.00 8.00 20.50 28.68 16.68 FAB12 x 8 A33 875-668N 1 19.00 3.50 9.50 23.00 31.50 19.50 FAB


14 x 10 A33 875-702N 1 22.00 4.50 11.50 27.00 37.00 23.00 FAB14 x 12 A33 875-704N 1 23.50 6.00 13.00 29.50 39.75 25.75 FAB


16 x 10 A33 875-736N 1 23.50 4.00 12.00 28.50 39.75 23.75 FAB16 x 12 A33 875-738N 1 25.00 5.50 14.25 31.00 42.75 26.75 FAB16 x 14 A33 875-740N 1 27.25 6.25 14.25 34.25 44.50 28.50 FAB



20 x 4 A33 875-814N 1 20.50 -1.75 8.50 22.50 36.75 16.75 FAB20 x 6 A33 875-816N 1 22.75 -0.25 10.00 25.75 39.75 19.75 FAB20 x 8 A33 875-818N 1 24.25 1.50 11.50 28.25 42.75 22.75 FAB

20 x 10 A33 875-820N 1 26.50 3.00 13.00 31.50 45.75 25.75 FAB20 x 12 A33 875-822N 1 28.00 4.25 14.25 34.00 48.50 28.50 FAB20 x 14 A33 875-824N 1 30.25 5.25 15.00 37.25 50.25 30.25 FAB20 x 16 A33 875-826N 1 31.75 6.50 16.50 39.75 53.00 33.00 FAB20 x 18 A33 875-828N 1 34.00 8.00 18.00 43.00 56.00 36.00 FAB

24 x 4 A33 875-904N 1 23.25 -3.00 9.25 25.25 42.50 18.50 FAB24 x 6 A33 875-906N 1 25.50 -1.50 10.75 28.50 45.50 21.54 FAB

137

Size(inch)


GJ(inch)

GN(inch)

H(inch)

HJ(inch)

L(inch)

N(inch)

Design

24 x 8 A33 875-908N 1 27.00 0.00 12.00 31.00 48.25 24.25 FAB24 x 10 A33 875-910N 1 29.25 1.75 13.50 34.25 51.25 27.25 FAB24 x 12 A33 875-912N 1 30.50 3.25 15.00 36.50 54.25 30.25 FAB24 x 14 A33 875-914N 1 33.00 4.00 16.00 40.00 56.00 32.00 FAB24 x 16 A33 875-916N 1 34.50 5.50 17.50 42.50 58.75 34.75 FAB24 x 18 A33 875-918N 1 36.75 6.75 18.75 45.75 61.50 37.50 FAB24 x 20 A33 875-920N 1 38.25 8.25 20.25 48.25 64.50 40.50 FAB

Sanitary Tee (SxSxS) Schedule 80 Harvel® PVC

Size(inch)


N(inch)

1 1/2 608 37R461501 5 1.75 2.752 608 37R461502 5 2.31 3.693 608 37R461503 5 3.06 4.884 608 37R461504 5 3.88 6.13

Cleanout Tee with Plug (SxSxFPT) Schedule 80 Harvel® PVC

Size(inch)

P/L Part No. Pack Qty HL(inch)

N(inch)

1 1/2 608 37R461101 2 2.07 1.802 608 37R461102 2 2.35 2.323 608 37R461103 2 3.51 3.634 608 37R461104 2 4.07 4.25

137

138138

Schedule 80 PVC Metal Transition Fittings

PVC-to-316SS Female Adapter (SxFPT) Schedule 80 Harvel® PVC



L(inch)

T(inch)

W(inch)

1∕2 A35 868-005SS 10 1.49 2.38 0.84 1.253∕4 A35 868-007SS 10 1.67 2.68 0.92 1.501 A35 868-010SS 6 1.98 3.11 0.96 1.75

1 1∕4 A35 868-012SS 5 2.19 3.45 1.04 2.121 1∕2 A35 868-015SS 5 2.35 3.73 1.04 2.50

2 A35 868-020SS 4 2.63 4.14 1.29 3.00

PVC-to-316SS Male Adapter (SxMPT) Schedule 80 Harvel® PVC



L(inch)

T(inch)

W(inch)

1∕2 A35 869-005SS 10 1.49 2.38 0.70 1.253∕4 A35 869-007SS 10 1.67 2.68 0.74 1.501 A35 869-010SS 6 1.98 3.11 0.92 1.75

1 1∕4 A35 869-012SS 5 2.19 3.45 0.95 2.121 1∕2 A35 869-015SS 5 2.35 3.73 0.99 2.50

2 A35 869-020SS 4 2.64 4.14 1.03 3.00

Metal Union End Connectors Type 375 (316 SS)

150 psi @ 73°F (10.3 bar @ 22.7°C)Union Sold Separately

Size(inch)


1∕2 A35 37X003314 13∕4 A35 37X003315 11 A35 37X003316 1

1 1∕4 A35 37X003317 11 1∕2 A35 37X003318 1

2 A35 37X003319 1

138

139138

Schedule 80 PVC Metal Transition Fittings

PVC-to-316SS Female Adapter (SxFPT) Schedule 80 Harvel® PVC



L(inch)

T(inch)

W(inch)

1∕2 A35 868-005SS 10 1.49 2.38 0.84 1.253∕4 A35 868-007SS 10 1.67 2.68 0.92 1.501 A35 868-010SS 6 1.98 3.11 0.96 1.75

1 1∕4 A35 868-012SS 5 2.19 3.45 1.04 2.121 1∕2 A35 868-015SS 5 2.35 3.73 1.04 2.50

2 A35 868-020SS 4 2.63 4.14 1.29 3.00

PVC-to-316SS Male Adapter (SxMPT) Schedule 80 Harvel® PVC



L(inch)

T(inch)

W(inch)

1∕2 A35 869-005SS 10 1.49 2.38 0.70 1.253∕4 A35 869-007SS 10 1.67 2.68 0.74 1.501 A35 869-010SS 6 1.98 3.11 0.92 1.75

1 1∕4 A35 869-012SS 5 2.19 3.45 0.95 2.121 1∕2 A35 869-015SS 5 2.35 3.73 0.99 2.50

2 A35 869-020SS 4 2.64 4.14 1.03 3.00

Metal Union End Connectors Type 375 (316 SS)

150 psi @ 73°F (10.3 bar @ 22.7°C)Union Sold Separately

Size(inch)


1∕2 A35 37X003314 13∕4 A35 37X003315 11 A35 37X003316 1

1 1∕4 A35 37X003317 11 1∕2 A35 37X003318 1

2 A35 37X003319 1

139

PVC-to-Brass Transition Fittings (SPG x FPT) Schedule 80 Harvel® PVC

150 psi @ 73°F (10.3 bar @ 22.7°C)

Size(inch)


HL(inch)

L(inch)

T(inch)

W(inch)

1∕2 A35 878-005BR 25 1.02 1.75 0.70 1.273∕4 A35 878-007BR 15 1.07 2.07 0.74 1.521 A35 878-010BR 15 1.32 2.44 0.81 1.93

1 1∕4 A35 878-012BR 15 1.38 2.49 0.85 2.291 1∕2 A35 878-015BR 10 1.44 2.74 0.87 2.60

2 A35 878-020BR 5 1.43 2.81 1.11 3.36

PVC-to-316 SS Transition Fittings (SPG x FPT) Schedule 80 Harvel® PVC

150 psi @ 73°F (10.3 bar @ 22.7°C)

Size(inch)


HL(inch)

L(inch)

T(inch)

W(inch)

1∕2 A35 878-005SS 25 1.02 1.75 0.70 1.273∕4 A35 878-007SS 15 1.07 2.07 0.74 1.521 A35 878-010SS 15 1.32 2.44 0.81 1.93

1 1∕4 A35 878-012SS 15 1.38 2.49 0.85 2.291 1∕2 A35 878-015SS 10 1.45 2.74 0.87 2.60

2 A35 878-020SS 5 1.43 2.81 1.11 3.36

139

140140

Schedule 80 PVC Expansion Joints

Expansion Joint 6" Travel (S x S) Schedule 80 Harvel® PVC

To order SxSPG add "P" to end of part number.To order FxF add "F" to end of part number.

Size(inch)

P/L EPDMPart No.

FKMPart No.

A(inch)

D(inch)

L(inch)

N(inch)

1∕2 634 826-005X6 836-005X6 3.00 1.86 13.97 12.173∕4 634 826-007X6 836-007X6 3.00 2.23 14.44 12.401 634 826-010X6 836-010X6 3.00 2.50 14.98 12.69

1 1∕4 634 826-012X6 836-012X6 3.00 2.89 15.56 12.981 1∕2 634 826-015X6 836-015X6 3.00 3.51 16.00 13.21

2 634 826-020X6 836-020X6 3.00 4.40 18.05 15.013 634 826-030X6 836-030X6 3.00 5.52 19.75 16.004 634 826-040X6 836-040X6 3.00 7.92 28.29 23.766 634 826-060X6 836-060X6 3.00 9.80 27.79 21.738 634 826-080X6 836-080X6 3.00 10.75 25.35 17.31

10 634 826-100X6 836-100X6 3.00 12.75 29.64 19.60

Expansion Joint 12" Travel (S x S) Schedule 80 Harvel® PVC

To order SxSPG add "P" to end of part number.To order FxF add "F" to end of part number.

Size(inch)

P/L EPDMPart No.

FKMPart No.

A(inch)

D(inch)

L(inch)

N(inch)

1∕2 634 826-005X12 836-005X12 6.00 1.86 23.10 21.303∕4 634 826-007X12 836-007X12 6.00 2.23 23.57 21.521 634 826-010X12 836-010X12 6.00 2.50 24.11 21.81

1 1∕4 634 826-012X12 836-012X12 6.00 2.89 24.69 22.111 1∕2 634 826-015X12 836-015X12 6.00 3.51 25.12 22.34

2 634 826-020X12 836-020X12 6.00 4.40 27.05 24.013 634 826-030X12 836-030X12 6.00 5.52 28.75 25.004 634 826-040X12 836-040X12 6.00 7.92 37.28 32.766 634 826-060X12 836-060X12 6.00 9.80 26.79 30.738 634 826-080X12 836-080X12 6.00 10.75 28.35 20.31

10 634 826-100X12 836-100X12 6.00 12.75 32.64 22.60

140

+ 27 21 702 0059

[email protected]

www.gf-africa.com

GF Africa Contact Details

Authorised Distributor

Date post:	03-Feb-2022
Category:	Documents
Upload:	others
View:	7 times
Download:	0 times

Section 3 Schedule 40 PVC Piping Systems

Documents