Section 3.1: Wires, Cables, and Connectors
Section 3.1: Wires, Cables, and Connectors
Scott Glogovsky andJonathon Sturm
Scott Glogovsky andJonathon Sturm
What the section covers…
What the section covers…
• Kinds and forms of wires• Kinds of cables• Connectors and their applications• Frequency effects within wires and cables
• Weird behaviors in cables• Impedance matching• Standing waves• Techniques for matching Impedances
• Kinds and forms of wires• Kinds of cables• Connectors and their applications• Frequency effects within wires and cables
• Weird behaviors in cables• Impedance matching• Standing waves• Techniques for matching Impedances
WiresWires• Wire diameter is expressed in terms of a gauge number
• The smaller the gauge, the larger the wire
• The larger the wire, the lower the resistance
• If too much current is sent through a wire, it is possible to heat the wire to its melting point
• See table 3.1
• Wire diameter is expressed in terms of a gauge number
• The smaller the gauge, the larger the wire
• The larger the wire, the lower the resistance
• If too much current is sent through a wire, it is possible to heat the wire to its melting point
• See table 3.1
Wire FormsWire Forms• Solid core
Useful for wiring bread boards Tend to break if flexed too many times
• Stranded wire Compromised of a number of individual strands Tends to conduct better due to its greater surface
area Doesn’t break as easily as solid core wire
• Braided wire Identical to stranded, only braided Often used as an electromagnetic shield in noise
reduction cables and as a wire conductor (like in coaxial cables)
• Solid core Useful for wiring bread boards Tend to break if flexed too many times
• Stranded wire Compromised of a number of individual strands Tends to conduct better due to its greater surface
area Doesn’t break as easily as solid core wire
• Braided wire Identical to stranded, only braided Often used as an electromagnetic shield in noise
reduction cables and as a wire conductor (like in coaxial cables)
Kinds of WireKinds of Wire• Pretinned solid bus wire
Includes a tin-lead alloy to enhance solderability
Often insulated with PVC, polyethylene, or Teflon
• Speaker wire High copper content Stranded wire
• Magnetic wire Used for building coils and electromagnets or anything requiring a large number of loops
Solid core insulated by a varnish coating
• Pretinned solid bus wire Includes a tin-lead alloy to enhance solderability
Often insulated with PVC, polyethylene, or Teflon
• Speaker wire High copper content Stranded wire
• Magnetic wire Used for building coils and electromagnets or anything requiring a large number of loops
Solid core insulated by a varnish coating
Cables-Typical Wire Configurations-
Cables-Typical Wire Configurations-
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Kinds of CablesKinds of Cables
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Cables DescribedCables Described• Paired and Twisted
Two individually insulated conductors Often used in DC or low frequency AC applications
• Twin Lead Flat, two wire line Maintains a 300 ohm impedance Primarily a transmission line between an antenna and a receiver
• Shielded Twin Lead Similar to paired, but contains a metal shield that is connected
to a ground• Unbalanced and Dual Coaxial
• Typically used to high-frequency signals like radio frequencies• Very reliable in terms of interference• Contains a solid core wire acting as the hot which is insulated
by polyurethane separating it from its ground shield. The shield is also insulated by an outer jacket
• Paired and Twisted Two individually insulated conductors Often used in DC or low frequency AC applications
• Twin Lead Flat, two wire line Maintains a 300 ohm impedance Primarily a transmission line between an antenna and a receiver
• Shielded Twin Lead Similar to paired, but contains a metal shield that is connected
to a ground• Unbalanced and Dual Coaxial
• Typically used to high-frequency signals like radio frequencies• Very reliable in terms of interference• Contains a solid core wire acting as the hot which is insulated
by polyurethane separating it from its ground shield. The shield is also insulated by an outer jacket
Cables Described (cont.)
Cables Described (cont.)
• Balanced Coaxial Same as coaxial, however it’s shield does not act as one
of the conductive paths• Ribbon
Used in low voltage applications where several wires are needed
Very flexible Often used in digital equipment
• Multiple Conductor An example would be phone lines or cat-5 ethernet and
communication cables• Fiberoptic
Transmit light through a glass material One cable generally consists of a number of individual
fibers
• Balanced Coaxial Same as coaxial, however it’s shield does not act as one
of the conductive paths• Ribbon
Used in low voltage applications where several wires are needed
Very flexible Often used in digital equipment
• Multiple Conductor An example would be phone lines or cat-5 ethernet and
communication cables• Fiberoptic
Transmit light through a glass material One cable generally consists of a number of individual
fibers
ConnectorsConnectors
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Connectors (Cont.)Connectors (Cont.)
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Connectors (Cont. again…)
Connectors (Cont. again…)
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Wiring SymbolsWiring Symbols
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Connector SymbolsConnector Symbols
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.