Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 00a. Assembly Beam Section 7 on Pile Cap.b. Assembly End closure beam on Beam Section 7 .

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 01a. Connected section 8 to strand jack.b. Make sure all connector are save to lift.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 02a. Lift the Section 8 until 700 mm up to top of pedestal.b. Install beam of temporary bridge for slide.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 03a. Make sure temporary bridge for slide.b. Degrading section 8 to temporary bridge.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 04a. Slide section 8 over than pedestal.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 05a. Connected Section 7 to strand jack.b. Make sure all connection in save condition.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 06a. Lift Section 7 until to true position.b. Connected all connector on true condition.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 07a. Slide section 8 to position for lift.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 8a. Connect section 8 to strand jack.b. Lift Section 8 up to 100 mm.c. Uninstall temporary bridge.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 09a. Uninstall temporary bridge.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 10a. Degrading Section 8 until on true position.

Title of Drawing:

PREPARED

DESIGN

APPROVED

CHECKED

Dwg.No:

Dwg. No:Referensi

REVISION

SCALEDIVISION RIGGING DEPARTMENTDIMENSIONS IN MILLIMETERS

PEMBANGUNAN JEMBATAN MERAH PUTIH BENTANG TENGAHRIGGING STUDY AND LIFTING PLAN

Step 11Finish

Section 8+ Step 00-Layout1Section 8+ Step 01-Layout1Section 8+ Step 02-Layout1Section 8+ Step 03-Layout1Section 8+ Step 04-Layout1Section 8+ Step 05-Layout1Section 8+ Step 06-Layout1Section 8+ Step 07-Layout1Section 8+ Step 08-Layout1Section 8+ Step 09-Layout1Section 8+ Step 10-Layout1Section 8+ Step 11-Layout1