+ All Categories
Home > Documents > SellosU Packing

SellosU Packing

Date post: 18-Jul-2016
Category:
Upload: andres
View: 227 times
Download: 1 times
Share this document with a friend
Description:
sellos
48
Catalog 5225A USA Rod and Piston U-Packing Seals/ Rod Wipers
Transcript
Page 1: SellosU Packing

Catalog 5225A USA

Rod and PistonU-Packing Seals/Rod Wipers

Page 2: SellosU Packing

Parker Hannifin CorporationEPS (formerly Packing) DivisionSalt Lake City, UtahPh: 801-972-3000

Rod and Piston Seals and Rod Wipers

i

Table of Contents

Introduction ........................................................................1

Available Elastomer Materials ............................................3

8400/8500 Series U-cups...................................................4

Rectangular, AN6226, US Series U-Cups ..........................5

BS, UR Series U-Rings.......................................................6

UP E4, E5 Series Seals.......................................................7

8400/8500 Series U-Rings Installation Dimensions............8

E4 Series Piston Seal Installation Dimensions..................14

E5 Series Rod Seal Installation Dimensions.....................16

AN6226 U-Ring Seal Installation Dimensions ..................18

US & UP Series Pistion Seal Installation Dimensions .......22

US, UR & BS Series Rod Seal Installation Dimensions ...30

BT & BR Profiles and Advanced Sealing System.............37

BT & BR Series Rod Seal Installation Dimensions ...........38

8600 Wipers .....................................................................39

Parker Rod Wiper Profiles ................................................42

Terms and Conditions of Sale ................ Inside Back Cover

© 1997, Parker Hannifin Corporation. All Rights Reserved.

Page 3: SellosU Packing
Page 4: SellosU Packing
Page 5: SellosU Packing
Page 6: SellosU Packing
Page 7: SellosU Packing
Page 8: SellosU Packing
Page 9: SellosU Packing
Page 10: SellosU Packing
Page 11: SellosU Packing
Page 12: SellosU Packing
Page 13: SellosU Packing
Page 14: SellosU Packing
Page 15: SellosU Packing
Page 16: SellosU Packing
Page 17: SellosU Packing
Page 18: SellosU Packing
Page 19: SellosU Packing
Page 20: SellosU Packing
Page 21: SellosU Packing
Page 22: SellosU Packing
Page 23: SellosU Packing
Page 24: SellosU Packing
Page 25: SellosU Packing
Page 26: SellosU Packing
Page 27: SellosU Packing
Page 28: SellosU Packing
Page 29: SellosU Packing
Page 30: SellosU Packing
Page 31: SellosU Packing
Page 32: SellosU Packing
Page 33: SellosU Packing
Page 34: SellosU Packing
Page 35: SellosU Packing
Page 36: SellosU Packing
Page 37: SellosU Packing
Page 38: SellosU Packing
Page 39: SellosU Packing
Page 40: SellosU Packing
Page 41: SellosU Packing

860000250 1/4 .250 +.000/-.001 .251 +.002/-.000 .370 +.002/-.000 .552 +.002/-.000 .203 +.005/-.000

860000312 5/16 .312 +.000/-.001 .313 +.002/-.000 .432 +.002/-.000 .614 +.002/-.000 .203 +.005/-.000

860000375 3/8 .375 +.000/-.001 .376 +.002/-.000 .495 +.002/-.000 .677 +.002/-.000 .203 +.005/-.000

860000437 7/16 .437 +.000/-.001 .438 +.002/-.000 .557 +.002/-.000 .739 +.002/-.000 .203 +.005/-.000

860000500 1/2 .500 +.000/-.001 .501 +.002/-.000 .620 +.002/-.000 .802 +.002/-.000 .203 +.005/-.000

860000562 9/16 .562 +.000/-.001 .563 +.002/-.000 .682 +.002/-.000 .864 +.002/-.000 .203 +.005/-.000

860000625 5/8 .625 +.000/-.001 .626 +.002/-.000 .745 +.002/-.000 .927 +.002/-.000 .203 +.005/-.000

860000687 11/16 .688 +.000/-.001 .689 +.002/-.000 .808 +.002/-.000 .990 +.002/-.000 .203 +.005/-.000

860000750 3/4 .750 +.000/-.001 .751 +.002/-.000 .870 +.002/-.000 1.052 +.002/-.000 .203 +.005/-.000

860000875 7/8 .875 +.000/-.001 .876 +.002/-.000 1.010 +.002/-.000 1.240 +.002/-.000 .218 +.005/-.000

860001000 1 1.000 +.000/-.001 1.001 +.002/-.000 1.135 +.003/-.000 1.365 +.003/-.000 .218 +.005/-.000

860001062 1-1/16 1.062 +.000/-.001 1.063 +.002/-.000 1.197 +.003/-.000 1.427 +.003/-.000 .218 +.005/-.000

860001125 1-1/8 1.125 +.000/-.001 1.126 +.002/-.000 1.260 +.003/-.000 1.490 +.003/-.000 .218 +.005/-.000

860001250 1-1/4 1.250 +.000/-.001 1.251 +.002/-.000 1.385 +.003/-.000 1.615 +.003/-.000 .218 +.005/-.000

860001312 1-5/16 1.312 +.000/-.001 1.313 +.002/-.000 1.447 +.003/-.000 1.667 +.003/-.000 .218 +.005/-.000

860001375 1-3/8 1.375 +.000/-.001 1.376 +.002/-.000 1.510 +.003/-.000 1.740 +.003/-.000 .218 +.005/-.000

860001500 1-1/2 1.500 +.000/-.001 1.501 +.002/-.000 1.635 +.003/-.000 1.865 +.003/-.000 .218 +.005/-.000

860001625 1-5/8 1.625 +.000/-.001 1.626 +.002/-.000 1.760 +.003/-.000 1.990 +.003/-.000 .218 +.005/-.000

860001750 1-3/4 1.750 +.000/-.001 1.751 +.002/-.000 1.885 +.003/-.000 2.115 +.003/-.000 .218 +.005/-.000

860001875 1-7/8 1.875 +.000/-.001 1.876 +.002/-.000 2.010 +.003/-.000 2.240 +.003/-.000 .218 +.005/-.000

Parker Hannifin CorporationPacking DivisionSalt Lake City, Utah

39

Rod and Piston Seals and Rod Wipers

Rod Wipers 8600 SeriesInstallation Dimensions

8600 WIPER NOMINAL "N" "P" "S: "D" "E"

PART PART ROD THROAT GROOVE GROOVE

NUMBER SIZE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE WIDTH TOLERANCE

8600 WIPERTYPICAL PART NUMBER

4181860001000

NOTE: Not all Wiper sizes listed are tooled in all compounds. Compound 4181 (80 Durometer Nitrile) is the standardmaterial. Other compounds available upon request. Special tooling may be required for other compounds.Nominal Rod Diameter to nearest fraction. Rod Diameter can vary from the dimension shown by +.005/-.005.However, more effective wiping action and optimum life will result if close tolerances are held.

Consult Parker Packing Customer Service at (801) 972-3000 for compound availability and additional sizes.

Page 42: SellosU Packing

Parker Hannifin CorporationPacking DivisionSalt Lake City, Utah

40

Rod and Piston Seals and Rod Wipers

Rod Wipers 8600 SeriesInstallation Dimensions

8600 WIPER NOMINAL "N" "P" "S: "D" "E"

PART PART ROD THROAT GROOVE GROOVE

NUMBER SIZE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE WIDTH TOLERANCE

860002000 2 2.000 +.000/-.001 2.001 +.002/-.000 2.135 +.003/-.000 2.365 +.003/-.000 .218 +.005/-.000

860002125 2-1/8 2.125 +.000/-.001 2.126 +.002/-.000 2.260 +.003/-.000 2.490 +.003/-.000 .218 +.005/-.000

860002187 2-3/16 2.188 +.000/-.001 2.189 +.002/-.000 2.323 +.003/-.000 2.683 +.003/-.000 .281 +.005/-.000

860002250 2-1/4 2.250 +.000/-.001 2.251 +.002/-.000 2.385 +.003/-.000 2.745 +.003/-.000 .281 +.005/-.000

860002437 2-7/16 2.437 +.000/-.001 2.438 +.002/-.000 2.572 +.003/-.000 2.932 +.003/-.000 .281 +.005/-.000

860002500 2-1/2 2.500 +.000/-.001 2.501 +.002/-.000 2.635 +.003/-.000 2.995 +.003/-.000 .281 +.005/-.000

860002687 2-11/16 2.688 +.000/-.001 2.689 +.002/-.000 2.823 +.003/-.000 3.183 +.003/-.000 .281 +.005/-.000

860002750 2-3/4 2.750 +.000/-.001 2.751 +.002/-.000 2.885 +.003/-.000 3.245 +.003/-.000 .281 +.005/-.000

860002875 2-7/8 2.875 +.000/-.001 2.876 +.002/-.000 3.010 +.003/-.000 3.370 +.003/-.000 .281 +.005/-.000

860002937 2-15/16 2.937 +.000/-.001 2.939 +.002/-.000 3.073 +.003/-.000 3.433 +.003/-.000 .281 +.005/-.000

860003000 3 3.000 +.000/-.002 3.001 +.003/-.000 3.135 +.003/-.000 3.495 +.003/-.000 .281 +.005/-.000

860003250 3-1/4 3.250 +.000/-.002 3.251 +.003/-.000 3.385 +.003/-.000 3.745 +.003/-.000 .281 +.005/-.000

860003437 3-7/16 3.437 +.000/-.002 3.439 +.003/-.000 3.573 +.003/-.000 3.933 +.003/-.000 .281 +.005/-.000

860003500 3-1/2 3.500 +.000/-.002 3.501 +.003/-.000 3.635 +.003/-.000 3.995 +.003/-.000 .281 +.005/-.000

860003687 3-11/16 3.688 +.000/-.002 3.689 +.003/-.000 3.823 +.003/-.000 4.183 +.003/-.000 .281 +.005/-.000

860003750 3-3/4 3.750 +.000/-.002 3.751 +.003/-.000 3.885 +.003/-.000 4.245 +.003/-.000 .281 +.005/-.000

860004000 4 4.000 +.000/-.002 4.001 +.003/-.000 4.135 +.003/-.000 4.495 +.003/-.000 .281 +.005/-.000

860004250 4-1/4 4.250 +.000/-.002 4.251 +.003/-.000 4.385 +.003/-.000 4.745 +.003/-.000 .281 +.005/-.000

860004437 4-7/16 4.437 +.000/-.002 4.439 +.003/-.000 4.573 +.003/-.000 4.933 +.003/-.000 .281 +.005/-.000

860004500 4-1/2 4.500 +.000/-.002 4.501 +.003/-.000 4.635 +.003/-.000 4.995 +.003/-.000 .281 +.005/-.000

8600 WIPERTYPICAL PART NUMBER

4181860001000

NOTE: Not all Wiper sizes listed are tooled in all compounds. Compound 4181 (80 Durometer Nitrile) is the standardmaterial. Other compounds available upon request. Special tooling may be required for other compounds.Nominal Rod Diameter to nearest fraction. Rod Diameter can vary from the dimension shown by +.005/-.005.However, more effective wiping action and optimum life will result if close tolerances are held.

Consult Parker Packing Customer Service at (801) 972-3000 for compound availability and additional sizes.

Page 43: SellosU Packing

Parker Hannifin CorporationPacking DivisionSalt Lake City, Utah

41

Rod and Piston Seals and Rod Wipers

Rod Wipers 8600 SeriesInstallation Dimensions

860005000 5 5.000 +.000/-.002 5.001 +.003/-.000 5.135 +.003/-.000 5.495 +.003/-.000 .281 +.005/-.000

860005187 5-3/16 5.187 +.000/-.002 5.189 +.003/-.000 5.323 +.003/-.000 5.683 +.003/-.000 .281 +.005/-.000

860005500 5-1/2 5.500 +.000/-.002 5.501 +.003/-.000 5.635 +.003/-.000 5.995 +.003/-.000 .281 +.005/-.000

860005625 5-5/8 5.625 +.000/-.002 5.626 +.003/-.000 5.760 +.003/-.000 6.120 +.003/-.000 .281 +.005/-.000

860006000 6 6.000 +.000/-.002 6.002 +.003/-.000 6.135 +.003/-.000 6.495 +.003/-.000 .281 +.005/-.000

860006375 6-3/8 6.375 +.000/-.002 6.377 +.003/-.000 6.510 +.003/-.000 6.870 +.003/-.000 .281 +.005/-.000

860006750 6-3/4 6.750 +.000/-.002 6.752 +.003/-.000 6.885 +.003/-.000 7.245 +.003/-.000 .281 +.005/-.000

860007000 7 7.000 +.000/-.002 7.002 +.003/-.000 7.135 +.003/-.000 7.495 +.003/-.000 .281 +.005/-.000

860007250 7-1/4 7.250 +.000/-.002 7.252 +.003/-.000 7.385 +.003/-.000 7.745 +.003/-.000 .281 +.005/-.000

860007750 7-3/4 7.750 +.000/-.002 7.752 +.003/-.000 7.885 +.003/-.000 8.245 +.003/-.000 .281 +.005/-.000

860008000 8 8.000 +.000/-.002 8.002 +.003/-.000 8.135 +.003/-.000 8.495 +.003/-.000 .281 +.005/-.000

860009000 9 9.000 +.000/-.002 9.002 +.003/-.000 9.135 +.003/-.000 9.495 +.003/-.000 .281 +.005/-.000

860010000 10 10.000 +.000/-.002 10.002 +.003/-.000 9.885 +.003/-.000 10.245 +.003/-.000 .281 +.005/-.000

8600 WIPER NOMINAL "N" "P" "S: "D" "E"

PART PART ROD THROAT GROOVE GROOVE

NUMBER SIZE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE DIAMETER TOLERANCE WIDTH TOLERANCE

8600 WIPERTYPICAL PART NUMBER

4181860001000

NOTE: Not all Wiper sizes listed are tooled in all compounds. Compound 4181 (80 Durometer Nitrile) is the standardmaterial. Other compounds available upon request. Special tooling may be required for other compounds.Nominal Rod Diameter to nearest fraction. Rod Diameter can vary from the dimension shown by +.005/-.005.However, more effective wiping action and optimum life will result if close tolerances are held.

Consult Parker Packing Customer Service at (801) 972-3000 for compound availability and additional sizes.

Page 44: SellosU Packing

42

Page 45: SellosU Packing

43

Page 46: SellosU Packing

44

Page 47: SellosU Packing

Build With The Best!

PPD 5225

Rod & U-Cup Seals

Parker Hannifin CorporationPacking DivisionSalt Lake City, UTPhone: (801) 972-3000Fax: (801) 972-4777

The items described in this document are hereby offered for sale at pricesto be established by Parker Hannifin Corporation, its subsidiaries and itsauthorized distributors. This offer and its acceptance by any customer(“Buyer”) shall be governed by all of the following Terms and Conditions.Buyerís order for any item described in its document, when communicatedto Parker Hannifin Corporation, its subsidiary or any authorized distributor(“Seller”) verbally or in writing, shall constitute accept of this offer.

1. Terms and Conditions of Sale: All descriptions, quotations,proposals, offers, acknowledgements, acceptance and sales of Seller’sproducts are subject to and shall be governed exclusively by the terms andconditions stated herein. Buyer’s acceptance of any offer to sell is limitedto these terms and conditions. Any terms or conditions in addition to, orinconsistent with those stated herein, proposed by Buyer in any accep-tance of an offer by Seller, are hereby objected to. No such additional,different or inconsistent terms and conditions shall become part of thecontract between Buyer and Seller unless expressly accepted in writing bySeller. Seller’s acceptance of any offer to purchase by Buyer is expresslyconditional upon Buyer’s assent to all the terms and conditions statedherein, including any terms in addition to, or inconsistent with thosecontained in Buyer’s offer. Acceptance of Seller’s products shall in allevents constitute such assent.

2. Payment: Payment shall be made by Buyer net 30 days from the dayof invoice of the items purchased hereunder. Parker reserves the right tocharge interest on all past due amounts. Any claims by Buyer foromissions or shortages in a shipment shall be waived unless Sellerreceives notice thereof within 30 days after Buyerís receipt of the shipment.

3. Delivery: Unless otherwise provided in the face hereof, delivery shallbe made F.O.B. Seller’s plant. Regardless of the method of delivery,however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier.Any delivery dates shown are approximate only and Seller shall have noliability for any delays in delivery.

4. Warranty. Seller warrants that the items sold hereunder shall be freefrom defects in material or workmanship at the time of delivery. THISWARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAIN-ING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHERWARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KINDWHATSOEVER. ALL OTHER WARRANTIES, INCLUDING, BUT NOTLIMITED TO, MERCHANTIBILITY AND FITNESS FOR PURPOSE,WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED.

NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIESWHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY,TO BUYERíS DESIGNS OR SPECIFICATIONS.

5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR INANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACTSHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THEITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BY BUYER, ATSELLERíS SOLE OPTION, IN NO EVENT SHALL SELLER BE LIABLE FORANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANYKIND OR NATURE WHATSOEVER, INCLUDING, BUT NOT LIMITED TOLOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THISAGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TOARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIED WAR-RANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE,FAILURE TO WARN OR STRICT LIABILITY.

6. Changes, Reschedules and Cancellations: Buyer may requestto modify the designs or specifications for the items sold hereunder as wellas the quantities and delivery dates thereof, or may request to cancel all orpart of this order, however, no such requested modification or cancellationshall become part of the contract between Buyer and Seller unlessaccepted by Seller in a written amendment to this Agreement. Acceptanceof any such requested modification or cancellation shall be at Seller’sdiscretion, and shall be upon such terms and conditions as Seller mayrequire.

7. Special Tooling: A tooling charge may be imposed for any specialtooling, including without limitation, dies, fixtures, molds and patterns,acquired to manufacture items sold pursuant to this contract. Such specialtooling shall be and remain Seller’s property notwithstanding payment ofany charges buy Buyer. In no event will Buyer acquire any interest inapparatus belonging to Seller which is utilized in the manufacture of theitems sold hereunder, even if such apparatus has been specially converted

8. Buyer’s Property: Any designs, tools, patterns, materials, drawings,confidential information or equipment furnished by Buyer or any other itemswhich become Buyer’s property, may be considered obsolete and may bedestroyed by Seller after two (2) consecutive years have elapsed withoutBuyer placing an order for the items which are manufactured using suchproperty. Seller shall not be responsible for any loss or damage to suchproperty while it is in Sellerís possession or control.

9. Taxes: Unless otherwise indicated on the face hereof, all prices andcharges are exclusive of excise, sales, use, property, occupational or liketaxes which may be imposed by any taxing authority upon the manufacture,sale or delivery of the items sold hereunder. If any such taxes must be paidby Seller or if Seller is liable for the collection of such tax, the amount thereofshall be in addition to the amounts for the items sold. Buyer agrees to pay allsuch taxes or to reimburse Seller therefore upon receipt of its invoice. IfBuyer claims exemption from any sales, use or other tax imposed by anytaxing authority, Buyer shall save Seller harmless from and against any suchtax, together with any interest or penalties thereon which may be assessed ifthe items are held to be taxable.

10. Indemnity For Infringement of Intellectual Property Rights: Seller shallhave no liability for infringement of any patents, trademarks, copyrights, tradedress, trade secrets or similar rights except as provided in this Part 10. Sellerwill defend and indemnify Buyer against allegations of infringement of U.S.patents, U.S. trademarks, copyrights, trade dress and trade secrets(hereunder “Intellectual Property Rights”). Seller will defend at its expenseand will pay the cost of any settlement or damages awarded in an actionbrought against Buyer based on an allegation that an item sold pursuant tothis contract infringes the Intellectual Property Rights of a third party. Seller’sobligation to defend and indemnify Buyer is contingent on Buyer notifyingSeller within ten (10) days after the Buyer becomes aware of such allegationsof infringement, and Seller having sole control over the defense of anyallegations or actions including all negotiations for settlement or compromise.If an items sold hereunder is subject to a claim that it infringes the IntellectualProperty Rights of a third party, Seller may, at its sole expense and option,procure for Buyer the right to continue using said item, place or modify saiditem so as to make it noninfringing, or offer to accept return of said item andreturn the purchase price less a reasonable allowance for depreciation.Notwithstanding the foregoing, Seller shall have no liability for claims ofinfringement based on information provided by Buyer, or directed to itemsdelivered hereunder for which the designs are specified in whole or part byBuyer, or infringements resulting from the modification, combination or use ina system of any item sold hereunder. The foregoing provisions of this Part 10shall constitute Seller’s sole and exclusive liability and Buyer’s sole andexclusive remedy for infringement of Intellectual Property Rights.

If a claim is based on information provided by Buyer or if the design for anitem delivered hereunder is specified in whole or in party by Buyer, Buyershall defend and indemnify Seller for all costs, expenses or judgementsresulting from any claim that such item infringes any patent, trademark,copyright, trade dress, trade secret or any similar right.

11. Force Majeure: Seller does not assume the risk of and shall not beliable for delay or failure to perform any of Seller’s obligations by reason ofcircumstances beyond the reasonable control of Seller (hereinafter “Events ofForce Majeure”). Events of Force Majeure shall include without limitation,accidents, acts of God, strikes or labor disputes, acts, laws, rules orregulations of any government or government agency, fires, floods, delays orfailures in delivery of carriers or suppliers, shortages of materials and anyother cause beyond Seller’s control.

12. Any special requirements for items to be provided by Seller hereunderincluding without limitation; compliance with military specifications, specialdocumentation, or testing requirements, must be communicated to Seller inwriting at the time the items are first requested. Any such requests that arecommunicated to Seller after preparation to manufacture an item hascommenced may result in additional charges for rework or remanufacture ofthe item.

13. Entire Agreement/Governing Law: The terms and conditions setforth herein, together with any amendments, modifications and any differentterms or conditions expressly accepted by Seller in writing, shall constitutethe entire Agreement concerning the items sold, and there are no oral orother representations or agreements which pertain thereto. This Agreementshall be governed in all respects by the law of the State of Ohio. No actionsarising out of the sale of the items sold hereunder or this Agreement may bebrought by either more than two (2) years after the cause of action accrues.

Offer Of Sale

Page 48: SellosU Packing

For fast, easy and accurate seal designassistance, ask for the latest version ofParker’s inPHorm™ Seal Design andMaterial Selection Software. Now avail-able for: Parker O-Rings Tech-Seal Static Seals CSS Standard Products Parker Hydraulic & Pneumatic Seals Chomerics EMI & Thermal Management Products

Parker Hannifin CorporationEPS Division (formerly Packing)2220 South 3600 WestSalt Lake City, UT 84119Phone: (801) 972-3000Fax: (801) 973-4019

Build With The Best!

Your Authorized Parker Seal Distributor:

For the latest information on all Parker Hannifin seal products, visit our website at www.parkerseals.com

10/99-2.5M-CTdigital rev. 12/2006

Parker Prädifa GmbHPostfach 1641, D-74306Bietigheim-Bissingen, GermanyPhone: (49) 7142-3510Fax: (49) 7142-351293


Recommended