The Department of Standards Malaysia (Standards Malaysia) a government agency under the Ministry of Science, Technology and Innovation (MOSTI) has established the Working Group (WG) on Stationary Source Emissions under the authority of Industry Standards Committee on Environmental Management. The working group had developed MS 1723:2017, Performance Evaluation of Air Pollution Control and Treatment Systems – Dry Dust Collectors – Specification (First Revision), this Malaysian Standard cancels and replaces MS 1723:2003, Performance Evaluation of Air Pollution Control and Treatment Systems: Mechanical Dust Collectors. The revised standard requires simultaneous inlet/outlet isokinetic measurements, implying a two sets of standard isokinetic measuring equipment and teams. The standard now allows for a different testing method that simplifies the test measurements to be more practical and safer in certain restrictive situations. Introduction Organised by: Objectives Target Groups 02 November 2017 (Thursday), Grand BlueWave Hotel, Shah Alam SEMINAR ON MS 1723:2017, PERFORMANCE EVALUATION OF AIR POLLUTION CONTROL AND TREATMENT SYSTEMS - DRY DUST COLLECTORS - SPECIFICATION (FIRST REVISION) The scope of the standard had been broadened to include all Dry Collection Systems, which now include Electrostatic Precipitators, Media Filters, Axial Flow Vortex Tubes Filter, Cyclones and Multicyclone Filters, etc. Due to the difficulties encountered in certain restrictive situation, an alternative method had been added to use the collected dust from the dust collector. An accurate flow measurements is used whereby the collected dust is compared with the emission concentration. Once this is done, the same principle is used to calculate the Dust Collector Performance. • Organisations and individuals involved in Air Pollution Control especially Consultants and Accredited Testing Laboratories that would like to expand their services to include Air Pollution Performance Evaluation leading to Environmental Technology Verification (ETV) • Government agency/Local authorities/Regulatory agency • Industries • Universities/Academia/Researcher Tel.: 03-5544 6343 (Rohayah)/[email protected]Tel.: 03-5544 6341 (Badariah)/[email protected]Fax: 03-5510 8830 Fees : Package A: RM150 (excluding standard) *Package B: RM200 (including standard) * Package fees exclusive of 6% GST. • Hardcopy Standard will be available if purchased 2 days before seminar. Dry Dust Collector System for a Palm Oil Mill Boiler
Transcript
The Department of Standards Malaysia (Standards
Malaysia) a government agency under the Ministry of
Science, Technology and Innovation (MOSTI) has
established the Working Group (WG) on Stationary
Source Emissions under the authority of Industry
Standards Committee on Environmental Management.
The working group had developed MS 1723:2017,
Performance Evaluation of Air Pollution Control and
Treatment Systems – Dry Dust Collectors – Specification
(First Revision), this Malaysian Standard cancels and
replaces MS 1723:2003, Performance Evaluation of Air
Pollution Control and Treatment Systems: Mechanical
Dust Collectors.
The revised standard requires simultaneous inlet/outlet
isokinetic measurements, implying a two sets of standard
isokinetic measuring equipment and teams. The standard
now allows for a different testing method that simplifies the
test measurements to be more practical and safer in
certain restrictive situations.
Introduction
Organised by:
Objectives
Target Groups
02 November 2017 (Thursday), Grand BlueWave Hotel, Shah Alam
SEMINAR ON MS 1723:2017, PERFORMANCE
EVALUATION OF AIR POLLUTION CONTROL AND TREATMENT
SYSTEMS - DRY DUST COLLECTORS - SPECIFICATION
(FIRST REVISION)
The scope of the standard had been broadened to include
all Dry Collection Systems, which now include
Electrostatic Precipitators, Media Filters, Axial Flow
Vortex Tubes Filter, Cyclones and Multicyclone Filters,
etc. Due to the difficulties encountered in certain
restrictive situation, an alternative method had been
added to use the collected dust from the dust collector. An
accurate flow measurements is used whereby the
collected dust is compared with the emission
concentration. Once this is done, the same principle is
* Package fees exclusive of 6% GST.• Hardcopy Standard will be available if purchased 2 days
before seminar.
Dry Dust Collector System for a Palm Oil Mill Boiler
Who are we?
Governed by the Standards of Malaysia Act 1996 (Act 549), the Department of Standards Malaysia
(Standards Malaysia) is an agency established on 28 August 1996 under the purview of the Ministry of
Science, Technology and Innovation (MOSTI). Standards Malaysia is the National Standards and
Accreditation Body of Malaysia providing confidence to various stakeholders, through credible
standardisation and accreditation services for global competitiveness. Our aspiration is to create a culture of
quality amongst Malaysians, to make standards an accepted component of businesses locally and to achieve
global recognition for our products and services; thus improving the overall quality of life. As the National
Standards Body, Standards Malaysia is entrusted to develop national standards (Malaysian Standards –
MS). Standards Malaysia has appointed six Standards Development Agencies (SDAs) to manage the
development of MS and coordinate Malaysia’s participation at international standardisation activities, i.e. ISOand IEC. The SDAs are:
SIRIM Berhad
Malaysian Timber Industry Board (MTIB)
Institut Kimia Malaysia (IKM)
Malaysian Association of Standards Users (Standards Users)
Malaysian Plastics Manufacturers Association (MPMA)
Malaysian Rubber Board (Lembaga Getah Malaysia, LGM)
Where to get MS, ISO and IEC standards?
For more than 20 years, we have successfully developed more than 6,000 MS and actively participated in
ISO and IEC standards development activities. This has contributed to Malaysia’s competitive edge by
facilitating trade through international recognition of our products and services that complied with MS orinternational standards. The MS can be purchased online through www.msonline.gov.my.
Need more information, further enquiries or interested in buying MS, ISO and IEC Standards?
Disclaimer: SIRIM STS SDN BHD is committed in ensuring the confidentiality,protection, security and accuracy of personal information made available toSIRIM Group in accordance with the Personal Data Protection Act 2010. It is yourobligation to ensure that all personal information submitted and retained isaccurate, not misleading, updated and complete in all aspects. SIRIM Group or itsauthorized officers shall not be responsible for any personal informationsubmitted by SIRIM Group Staff that is inaccurate, misleading, incomplete or notupdated.
Please refer to our Personal Data Protection Policy at http://www.sirim.my/privacy/pdpa for further information.
