Service Informationservicenet.indesitcompany.com/data/img_sm/sm60678.pdf · 2016. 5. 18. ·...

Whirlpool UK Appliances Ltd© 2016 Reg. Office: Peterborough PE2 9JB Registered in London: 106725

ServiceInformation

INDESIT60 cmT BOX

COOKER HOODS

Models Comm.Covered Code

IHT6.5CMIX 83656IHT6.5FCMIX 84326IHT6.5SCMIX 87344

5413427 Issue 1 May 2016

C00309618 ~ SM004053

Changes in this Issue• New Service Manual• New Models Introduced

2 of 25

Service Manual UK

Whirlpool UK Appliances Ltd

English

SAFETY NOTES & GENERAL SERVICING ADVICE1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.2. It should ONLY be used by suitably qualified persons having technical competence applicable

product knowledge and suitable tools and test equipment.3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)

from the electrical supply.4. Servicing must be preceded by Earth Continuity and Insulation Resistance checks.5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances which

are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.) checks must be made for leaks from seals gaskets and pipe work and rectification carried out where necessary.

7. It can be dangerous to attempt ‘DIY repairs / maintenance on complex equipment and the Company recommends that any problem with the appliance is referred to its own Service Organisation.

8. Whilst the Company has endeavoured to ensure the accuracy of the data within this publication they cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.

SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION

Serial Number Example

3 10 02 0895

Four remaining digits = Build number that day 895th builtThird two digits = Day of manufacture 2nd of monthSecond two digits = Month of manufacture OctoberFirst digit = Year of manufacture 2013

Industrial Code Example

37 24455 0010

Last four digits = 0000 original production.

Second five digits = COMMERCIAL CODE*

First two digits = Factory of origin* Vital for correct model information and system identification

Other numbers denote major production changes

3 of 25


Service Manual UK English

INDEX

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Installation of the Cooker Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 11How Best to Use the Cooker Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Installation & Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 15The Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Maintenance & Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 - 17Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Servicing & Dismantling Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 - 23Items Supplied. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4 of 25

Service Manual UK


English

INTRODUCTION OF INDESIT T BOX COOKER HOODSModel IHT6.5CMIX was introduced to the Indesit range during June 2013.Model IHT6.5FCMIX was introduced to the Indesit range during July 2013.Model IHT6.5SCMIX was introduced into the Indesit range during September 2014.They have mechanical push button controls, 2 halogen lamps, 3 speeds and washable grease filters.Models IHT6.5CMIX and IHT6.5SCMIX are not supplied with a carbon filter.

Legend

TECHNICAL SPECIFICATIONSModel Comm. Code Colour First ProducedIHT6.5CMIX 83656 Stainless Steel June 2014IHT6.5FCMIX 84326 Stainless Steel July 2014IHT6.5SCMIX 87344 Stainless Steel September 2014

Country of Origin Poland

General Mechanical push button controls2 Halogen Lamps3 SpeedsDishwasher safe metal filter

Dimensions - cm Height Width Depth61 - 82 59.8 50.6

Sound 61 dB @ maximum speed

IEC Extraction Rate 490 (m3/h)

Electrical Supply 230/240Volts AC @ 50Hz

Cable Length Overall length 1.5 Metres - 2 core double insulatedHAR H05VVH2-F 2 x 0.75, no plug fitted

Fuse Rating 5 amp

PowerIHT6.5CMIX Total rating 140W @ 230V, 0.60 ampsIHT6.5FCMIX Total rating 185W @ 230 volts, 0.80 ampsIHT6.5SCMIX Total rating 205W @ 230 volts, 0.90 amps

Grease Filter C00298161 x 2

I H T 6 F.5 C M I X

I = Indesit 6 = 600 mmT = T Box F = CarbonFilterBlank = NoCarbon Filter

C = HalogenLamp 25W

I = S SteelFilter

X = StainlessSteel

M = MechanicalButtons

H = DecorativeHood

.5 = GPZ500Motor.5S = GPZ500SMotor

5 of 25



Carbon Filter C00298735 supplied (not IHT6.5CMIX or IHT6.5SCMIX)

Air Outlet 120 - 150 mm

MotorIHT6.5CMIX & IHT6.5FCMIX 90W, GPZ500IHT6.5SCMIX 155W, GPZ500S, FIME VEN0092509

Lamp Halogen Lamps x 2 - 25 Watt, G9, 230V

These appliances conform to the following EEC Directives: -

2006/95/EC of 12/12/2006 (Low Voltage) and subsequent modifications;2004/108/EEC of 15/12/2004 (Electromagnetic Compatibility) and subsequent modifications;

6 of 25

Service Manual UK


English

DISPOSALTo minimise the risk of injury to children please dispose of your product carefully and safely.This unit is marked for conformity with European Directive 2012/19/EC, Waste Electrical and Electronic Equipment (WEEE). By ensuring that the unit is scrapped properly, the use contributes to safeguarding the environment and public health.Remove all doors and lids where applicable. Remove the mains cable (where fitted) by cutting off flush with the appliance and always ensure that no plug is left in a condition where it could be connected to the electricity supply.To help the environment, Local Authority instructions should be followed for the disposal of the product.

Disposal of Old Electrical Appliances The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.The crossed out 'wheeled bin' symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

7 of 25



INSTALLATION OF THE COOKER HOOD

Not supplied withIHT6.5CMIX &IHT6.5SCMIX

8 of 25

Service Manual UK


English

INSTALLATION OF THE COOKER HOOD

9 of 25



INSTALLATION OF THE COOKER HOOD continued

10 of 25

Service Manual UK


English


11 of 25




12 of 25

Service Manual UK


English

HOW BEST TO USE THE COOKER HOODCorrect use and maintenance of the hood require a few very simple operations, allowing the product to reach its full potential.

Incorrect Use

Switching on the hood only when there are unpleasant odours.

Correct Use

The hood must ALWAYS be switched on when you start cooking and kept running for a few minutes after cooking has finished.

Always using the hood at maximum speed.

The hood must initially be switched on at the minimum speed, then the speed must be increased when the cooking produces large amounts of smoke and vapour. Only in extreme situations should the booster speed be used.

Not replacing the charcoal filter (filter version).

Not replacing the charcoal filter when necessary generates an increase in the noise level of the hood due to a malfunctioning of the motor.

Connecting the hood to narrow ducting.

The connection of the hood to ducting with a small diameter or multiple bends creates power loss and affects product efficiency.

Testing performance from within the room.Appliance function is tested against the performance data from the vent outlet position only.

13 of 25



GENERAL SAFETY

Taken from the User Handbook.Keep the instruction book for reference. If you sell, transfer or move the unit to another location, make sure to keep the book with the product.Read the instructions carefully - they contain important installation, user and safety information.Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts.

The distance between the cookware support surface on top of the cooking appliance and the lowest part of the cooker hood must be at least:65 cm if the hood is installed over a gas cooktop55 cm if the hood is installed over an electric cooktop.If the installation instruction manual for the gas cooking appliance specifies a greater distance, this measurement should be taken into account.The cooker hood comes complete with anchor plugs which are suitable for use with most walls/ceilings.However, you must contact a qualified technician to check the suitability of the materials in relation to the type of wall / ceiling, which must be strong enough to support the weight of the unit.Caution! Do not connect the unit up to its electrical power supply until the installation has been completed.Before cleaning or servicing the unit, disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker.Always wear work gloves when installing and servicing the unit.It is not intended for use by children or persons with sensory or mental disability and lack of experience or familiarity, except under the supervision or instruction of a person responsible for their safety.Make sure children do not play with the unit.Never operate the unit without its grease filter.Never use the hood as a support, unless expressly instructed to do so.The room must be adequately ventilated if the hood is used at the same time with other equipment burning gas or other fuels.Extracted air must not be conveyed into a duct used for exhausting combustion fumes from gas or other fuel-fired equipment.Observe all regulations in relation to air extraction.NEVER cook food with an open flame under the hood; open flames will damage the filters and may cause fires. Never do this.Always supervise frying to make sure the heated oil does not catch fire.Strictly observe all local regulations in relation to the technical and safety measures to be employed in fumes extraction.Clean the product frequently, inside and out (AT LEAST ONCE A MONTH), and in observance of the maintenance instruction given in this manual).Failure to observe the hood cleaning and filter cleaning / replacement instructions can result in fires.Never use the hood without its bulbs properly installed - electrocution hazard.The manufacturer is not liable for any inconvenience, damage or fire caused by the by the unit as a result of failure to observe the instructions given in this manual.Caution! The unit’s accessible parts can get very hot when used with cooking equipment.

14 of 25

Service Manual UK


English

INSTALLATION

ELECTRICAL CONNECTIONThe mains voltage must match that given on the ratings label inside the hood itself. If the hood has a power plug, connect the hood to an easily accessible regulatory power socket. If it does not (direct connection to the mains), or the socket is not easily accessible, install a two-pole regulatory switch to enable total disconnection from the mains in case of category III over voltage, as required by the installation regulations.Caution! Always check that the mains cable is connected up properly and check that it operates correctly before reconnecting the hood to the mains.

Air Exhaust (for Ducted Units)Connect the hood to a duct and wall exhaust hole of a diameter equal to that of the air outlet flange. Using a smaller diameter tube and exhaust hole reduces the extraction capacity of the hood and also increases its running noise.The manufacturer is not liable for any consequences of doing so.• Use the shortest duct required to achieve the purpose.• Use a duct with as few bends as possible.• Avoid suddenly changing the diameter of the duct.• The duct must have as smooth an inner surface as possible.• The duct must be made of regulatory material.• Do not connect the hood to flues carrying combustion fumes from other equipment (boilers,

chimneys, stoves, etc.).• Observe the instructions of the competent authorities in relation to the air exhaust. The air being

exhausted may not be exhausted into a wall cavity unless the cavity in question is specifically intended for this purpose.

• Equip the room with air intakes to prevent the hood creating suction pressure in the interior (this must not exceed 0.04 mbar).

• The manufacturer is not liable for any consequences of failure to observe these instructions.

Filter or Ducted?Your hood is supplied as a ducted unit.If you wish to use it as a filter unit, you must install the proper ACCESSORY KIT.Note: Supplied with the hood (not IHT6.5CMIX & IHT6.5SCMIX), the accessory active charcoal filter unit may already be installed.Instructions for transforming the hood from the ducted to the filter version are given in this manual See 'Filter Version'.

Ducted VersionThe hood purifies the air and expels it outdoors via an exhaust duct (diameter 150mm) connected to its outlet flange.The diameter of the exhaust tube must be equal to that of the outlet flange.Caution! The exhaust duct is not supplied and must be purchased separately.When routed horizontally, the tube must be angled slightly upwards (around 10°) to enable the air to be conveyed more easily. If the hood is fitted with charcoal filters, they must first be removed.

15 of 25



Filter VersionThe hood purifies the air and returns it to the room. This version of the hood requires installation of an accessory active charcoal filter unit.This version requires an air deflector. a reduction adaptor and the charcoal filter. The top tube must have its air outlet slots uppermost.

THE CONTROLS

T1 Motor ResetPress the button while the hood is in operation turns it OFF.

T2 Speed 1Pressing the button sets the hood to speed 1.



T5 Lights ON/OFFThis button is independent of the other controls.

T1 T2 T3 T4 T5

16 of 25

Service Manual UK


English

MAINTENANCE & CARECaution:Before cleaning or servicing the unit disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker.

First Cleaning• Remove the protective film.• Clean with a damp sponge and a little neutral soap.• Rinse off with a damp cloth.• Dry with a soft cloth; if the hood is stainless steel, dry along the metal's grain.

Periodic CleaningThe hood must be cleaned frequently (at least as often as you service the grease filter), inside and out. Use a damp cloth and a neutral liquid detergent with lukewarm water.Do not use abrasive or corrosive products.Warning: Failure to observe the hood cleaning and filter cleaning/replacement instructions can result in fires. Follow the instructions carefully. The manufacturer is not liable for any damage to the motor or fires caused by incorrect care or failure to follow the above instructions.

Servicing the Grease Filter (A)The grease filter retains the particles of grease produced during cooking; it must be cleaned at least once a month with a non-aggressive detergent, either by hand or with a low temperature, short dishwasher cycle.To extract the grease filter, pull the spring loaded handle.If washed in a dishwasher, the metal filter may change colour, but this does not affect performance.

Servicing the Charcoal Filter (B) (if fitted)The charcoal filter retains unpleasant cooking odours.The filter saturates after a variable time, depending on the type of cooking and how often the grease filter is cleaned. The cartridge must be replaced at least once every twenty months.This filter CANNOT be washed or regenerated.Disassembly: Remove the activated carbon filter by pressing the two front levers which secure it to the hood.Assembly: Secure the activated carbon filter first in the back using the hoods metal tabs and then in the front by pressing the two levers.

A

B

B

17 of 25



Replacing the BulbsDisconnect the unit from the mains and remove the grease filter.Caution! Make sure the bulbs are cool before touching them.1. Extract the guard by prising it out with a small flat head

screwdriver or something similar.2. Replace the faulty bulb. Use only bulbs of the same type.3. Refit the guard (push it in).

TROUBLESHOOTINGIf something does not work, first check the following:

If the hood does not operate:Check that:• The unit is powered up;• A speed has been set.

If the hood is not working effectively:Check that:• The selected motor speed is sufficient to handle the amount of smoke and steam being

produced.• The kitchen is adequately ventilated for the unit to take air in.• The charcoal filter is not exhausted (filter version).

If the hood turns off during normal operation:Check that:• The unit is powered up;• The circuit breaker has not tripped.

In the case of faulty operation, first disconnect the machine from the mains for at least 5 seconds by pulling its plug, then reconnect it.

18 of 25

Service Manual UK


English

WIRING DIAGRAM

MOTOREROSSO (COM.)

BLU (VEL. 1)

GRIGIO (VEL. 2)

NERO (VEL. 3)

ALO 220V

ALO 220V

230V

3.leV2.leV1.leVECUL Reset

L

N

5413370wd.pdfHHP6.5/7.5/9.5CM16002911100

19 of 25



SERVICING & DISMANTLING PROCEDURES

Safety Notes1. Refer to the Safety Notes on Page 2 of this manual.2. Before carrying out any work ensure that the appliance is disconnected from the mains

supply.3. To undertake any dismantling, with the exception of the light bulbs and filter

replacement, remove the hood from its location and place on a protected surface.4. Personal safety precautions must be taken to protect against accidents caused by sharp

edges on metal, glass and plastic parts.All illustrations / photographs show model IHT6.5SCMIX

A) Grease & Carbon Filter (if fitted)1. To extract the grease filters, pull the spring loaded handle, (Fig. A).2. The carbon filter (Fig. B) if used, remove by pressing the two front levers which secure it to the

hood.Assembly: Secure the carbon filter first in the back using the hoods metal tabs (Fig. C) and then in the front by pressing the two levers.

B) Lamp Assembly1. Disconnect the unit from the mains and remove the grease filters.2. Remove the two screws securing the lamp assembly trim and lower the trim, Fig. 1.

continued ....

B

ABC

Fig. 1

Fig. 3

20 of 25

Service Manual UK


English

3. Disconnect the wiring to the lamp assembly to be replaced, also remove the cable tie, Fig. 2.4. Squeeze the tabs either side and push the lamp assembly out, Fig. 3.

5. Connect the wiring to the new lamp assembly and reassemble in reverse order.

C) Halogen Lamp ReplacementCaution! Make sure the bulbs are cool before touching them and avoid touching them with bare hands.

1. Remove the glass cover and frame using a small screwdriver or similar tool, Figs. 4 & 5.2. Replace the bulb with same type G9, 25 Watts.

Note: Do not touch the lamp with bare hands.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

21 of 25



D) Control Switch Bank (incuding Cables)1. Remove the grease filters as in (A).2. Remove the lamp assembly trim, two screws, Fig. 1.3. Remove the two fixing screws along the front edge of the canopy, Fig. 6 and lower the bracket.4. To remove the switch bank from the bracket, release the two screws that secure it to the bracket,

Fig. 7.

5. Release the cover by removing the four screws circled in Fig. 8. On reassembly ensure no wires are trapped under the cover.

6. Unclip the button trim by pressing on the 4 securing tabs, Fig. 9.7. Disconnect the power supply cable (if required) to the switch bank by releasing the 2 screws

circled, Fig. 10.

8. Disconnect the wiring to the lamps.

Fig. 6 Fig. 7

Fig. 8

Fig. 10

Fig. 9

22 of 25

Service Manual UK


English

9. Using a small flatbladed screwdriver, carefully release at the top first and then completely remove the controls / motor cable cover, Fig. 11.

10. Disconnect the cable to the motor, Fig. 12, by squeezing the tabs and pulling out the plug.

11. While supporting the motor, remove the four screws (red circles) that secure the motor in order to extract the cable fully out of the slot, Fig. 13. Remove the two screws securing the power supply cable (yellow circle), Fig. 13.

12. Reassemble in reverse order.

E) Motor1. Remove the grease filters as in (A).2. While supporting the motor, remove the four screws that secure the motor, Fig. 13.3. Using a small flatbladed screwdriver, carefully release at the top first and then completely remove

the controls / motor cable cover, Fig. 11.4. Disconnect the cable to the motor by squeezing the tabs and pulling out the plug, Fig. 12.

continued...

Fig. 11 Fig. 12

Fig. 13

23 of 25

Service Manual UK


English

5. In order to remove the motor, the surround may need to be released (six screws) and either pulled forward or after feeding through both cables, lifting to allow space for the removal of the motor.

6. Reassemble in reverse order.

Fig. 13

24 of 25

Service Manual UK


English

ITEMS SUPPLIED

NOTE: - The Carbon Filter and Air Deflector are not shown and are only supplied with model IHT6.5FCMIX.

25 of 25

Service Manual UK


English

Date post:	17-Mar-2021
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

Service Informationservicenet.indesitcompany.com/data/img_sm/sm60678.pdf · 2016. 5. 18. ·...

Documents