1
SERVICE MANUAL FE-2 CHASSISMODEL COMMANDER DEST CHASSIS NO.
KV-21LT1B RM-887 French SCC-Q54C-A
KV-21LT1E RM-887 Spanish SCC-Q53C-A
KV-21LT1K RM-887 OIRT SCC-Q51C-A
KV-21LT1U RM-887 UK SCC-Q52C-A
MODEL COMMANDER DEST CHASSIS NO.
KV-21FT2K RM-887 OIRT SCC-Q51E-A
RM-889
KV-21LT1
RM-887
KV-21FT2
2
TABLE OF CONTENTS
Section Title Page Section Title Page
Specifications .................... 3Connectors .................... 5Self Diagnostic Software .................... 6
1. GENERALSwitching On the TV andAutomatically Tuning .................... 7Introducing the Menu System .................... 8Teletext .................... 10Connecting Optional Equipment.................... 10Using Optional Equipment .................... 10Troubleshooting .................... 11
2. DISASSEMBLY
KV-21LT1
2-1. Rear Cover Removal .................... 122-2. A Board PWB Removal 1 .................... 122-3. A Board PWB Removal 2 .................... 122-4. Service Position .................... 122-5. Wire Dressing .................... 122-6. Picture Tube Removal .................... 13
KV-21FT2
2-7. Rear Cover Removal .................... 142-8. Chassis Removal .................... 142-9. Service Position .................... 142-10. Wire Dressing .................... 142-11. Picture Tube Removal .................... 15
3. SET-UP ADJUSTMENTS3-1. Beam Landing .................... 163-2. Convergence .................... 173-3. Focus Adjustment .................... 193-4. Screen (G2), White Balance .................... 19
4. CIRCUIT ADJUSTMENTS4-1. Electrical Adjustments .................... 204-2. Test Mode 2 .................... 22
5. DIAGRAMS5-1. Circuit Board Location .................... 245-2. Block Diagrams .................... 255-3. Schematic Diagrams and
Printed Wiring Boards .................... 24* C Board .................... 29* A Board .................... 31
5-4. Semiconductors .................... 395-5. IC Blocks .................... 41
6. EXPLODED VIEWS6-1. Chassis (KV-21LT1) .................... 42
Chassis (KV-21FT2) .................... 446-2. Picture Tube(KV-21LT1) .................... 43
Picture Tube(KV-21FT2) .................... 45
7. ELECTRICAL PARTS LIST .................... 46
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THEANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THECARBON PAINTED ON THE CRT, AFTER REMOVAL OF THEANODE CAP.
WARNING !!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING ANYSERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TOLIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS DIRECTLYCONNECTED TO THE POWER LINE.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY SHADING AND MARKED £ ONTHE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THEPARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACETHESE COMPONENTS WITH SONY PARTS WHOSE PARTNUMBERS APPEAR AS SHOWN IN THIS MANUAL OR INSUPPLEMENTS PUBLISHED BY SONY.
ATTENTION
APRES AVOIR DECONNECTE LE CAP DE’LANODE,COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET CELUIDE L’ANODE DU CAP AU CHASSIS METALLIQUE DE L’APPAREIL,OU AU COUCHE DE CARBONE PEINTE SUR LE TUBECATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE.
ATTENTION !!
AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANTD’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEURD’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGELE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈÁ L’ALIMENTATION SECTEUR.
ATTENTION AUX COMPOSANTS RELATIFS ÁLA SECURITÈ!!
LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNEMARQUE £ SUR LES SCHÈMAS DE PRINCIPE, LES VUESEXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR-TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT,NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LENUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUELOU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
3
LEDOMMETI metsySnoisiveleT egarevoClennahC metsySroloC
hcnerF I,L,H/G/B
01F-2F,21E-2E:FHV96E-12E:FHU
Q-B,02S-1S,30S-10S:VTELBAC14S-12S:REPYH
96F-12F,01F-20FL96B-12B:FHUI
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
hsinapS H/G/B
21E-2E:FHV96E-12E:FHU
02S-1S,30S-10S:VTELBAC14S-12S:REPYH
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
TRIO K/D,H/G/B
21R-10R,21E-2E:FHV96R-12R,96E-12E:FHU
02S-1S,30S-10S:VTELBAC14S-12S:REPYH
MACES,LAP85.3CSTN,34.4CSTN
)NIOEDIV(
KU I 96B-12BFHU:IMACES,LAP
85.3CSTN,34.4CSTN)NIOEDIV(
ledoM K2TF12-VK B1TL12-VK E1TL12-VK K1TL12-VK U1TL12-VK
noitpmusnoCrewoP W55 W55 W55 W55 W67
ebuTerutciP
nortinirTDFyalpsiDtalF)sehcni12(mc55.xorppA
derusaemerutcipmc15.xorppA()yllanogaid
noitcelfedeerged011
tuptuodnuoS
:U1TL12/K1TL12/E1TL12/B1TL12)rewoPcisuM(W8x1
)onoMSMR(W4x1
:K2TF12)rewoPcisuM(W6x2
)onoMSMR(W3x2
]RAER[slanimreTtuptuO/tupnI stnemeriuqeRrewoP V042-022
rotcennocoruEnip-12:1)dradnatsCELENEC(
.slangisoediVdnaoiduArofstupnI.BGRrofstupnI
.slangisoiduAdnaoediVVTfostuptuOsnoisnemiD
:U1TL12/K1TL12/E1TL12/B1TL12mm784x874x415xorppA
:K2TF12mm774x084x884xorppA
]TNORF[slanimreTtuptuO/tupnI thgieW:U1TL12/K1TL12/E1TL12/B1TL12
gk42xorppAgk1.62xorppA:K2TF12
tupnioediV kcajonohp seirosseccAdeilppuS)1(rednammoCetomeR788-MR
)2(yrettab6RdetangisedCEI
tupnioiduA kcajonohp serutaeFrehtO,kniltramS,remiTpeelS,txeteleT
noitcetedotuAmetsysVT
kcajenohpdaeH kcajinimoerets
metsyslortnocetomeR lortnocderarfnI
stnemeriuqerrewoPcdV3
noitangisedCEIseirettab2)AAezis(6R
.ecitontuohtiwegnahcottcejbuserasnoitacificepsdnangiseD
4
WARNING (UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused plughaving a fuse of 5 AMP rating. Should the fuse need to be replaced, usea 5 AMP FUSE approved by ASTA to BS 1362, ie one that carries theASAT mark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLEFOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUTOFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVEREDFROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITHBARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with a5 AMP FUSE, otherwise the circuit should be protected by a 5 AMPFUSE at the distribution board.
How to replace the fuse.Open the fuse compartment witha screwdriver blade and replacethe fuse.
FUSE
emaNledoMmetI
K2TF12-VK B1TL12-VK E1TL12-VK K1TL12-VK U1TL12-VK
bmoClaP FFO FFO FFO FFO FFO
PIP FFO FFO FFO FFO FFO
ytiroirPBGR FFO NO NO FFO NO
xoBrefooW FFO FFO FFO FFO FFO
1tracS NO NO NO NO NO
2tracS FFO FFO FFO FFO FFO
)3(nitnorF FFO FFO FFO FFO FFO
4tracS FFO FFO FFO FFO FFO
rotcejorP FFO FFO FFO FFO FFO
edom9:61niBKA FFO FFO FFO FFO FFO
G/BmroN NO NO NO NO FFO
ImroN FFO NO FFO FFO NO
K/DmroN NO FFO NO FFO FFO
SUAmroN FFO FFO FFO FFO FFO
LmroN FFO NO FFO FFO FFO
TASmroN FFO FFO FFO FFO FFO
MmroN FFO FFO FFO FFO FFO
txeteleT NO NO NO NO NO
oeretSmaciN FFO FFO FFO FFO FFO
5
21 pin connector
Connected Not Connected (open) * at 20Hz - 20kHz
Pin No 1 2 4 Signal Signal level
1 Audio output B(right)
Standard level : 0.5V rmsOutput impedence : Less than 1kohm*
2Audio output B(right)
Standard level : 0.5V rmsOutput impedence : More than 10kohm*
3Audio output A(left)
Standard level : 0.5V rmsOutput impedence : Less than 1kohm*
4 Ground (audio)
5 Ground (blue)
6 Audio input A(left)
Standard level : 0.5V rmsOutput impedence : More than 10kohm*
7 Blue input 0.7 +/- 3dB, 75 ohms positive
8 Function select(AV control)
High state (9.5-12V) : Part mode Low state (0-2V) : TV modeInput impedence : More than 10K ohmsInput capacitance : Less than 2nF
9 Ground (green)
10 Open
11 Green Green signal : 0.7 +/- 3dB, 75 ohms, positive
12 Open
13 Ground (red)
14 Ground (blanking)
15
_ _ Red input 0.7 +/- 3dB, 75 ohms, positive
_ (S signal Chroma input)
0.3 +/- 3dB, 75 ohms, positive
16 Blanking input(Ys signal)
High state (1-3V) Low state (0-0.4V)Input impedence : 75 ohms
17 Ground (video output)
18 Ground (video input)
19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
20
_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
_ Video inputY (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V(-3+10dB)
21 Common ground(plug, shield)
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
Front Connection Panel
KV-21LT1
Rear Connection Panel
KV-21FT2
KV-21LT1 KV-21FT2
6
FE-2 SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event ofone of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) andthen communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will bedisplayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.Each time the software detects an error it is stored within the NVM. See Table 2.
Flash Timing Example : e.g. error number 3
StBy LED
ON ON ON
OFF OFF
egasseMrorrEDELedoC
rorreoN 00devreseR 10
)noitcetorPtnerruCrevO(PCO 20devreseR 30
cnySlacitreVoN 40BKAelbatsnU 50
norewoptawolsenilatadro/dnakcolcsubCII 60norewoptaegdelwonkcasubCIIonMVN 70
desUtoN 80norewoptaegdelwonkcaonrenuT 90
desutoN 01NOrewoPtaegdelwonkcaonrellortnocelgnuJ 11
Table 1 How to enter into Table 2
1. Turn on the main power switch of the TV set and enter into the‘Stanby Mode’.
2. Press the following sequence of buttons on the RemoteCommander.
i+ 5 -(ON SCREEN (DIGIT 5) (VOLUME -) (TV) DISPLAY)
3. The following table will be displayed indicating the error count.
Table 2
Note: To clear the error count data press ‘80’ on the Remote commander.
UNEMRORRE
20E30E40E50E60E70E80E90E01E11E
GNIKROWEMIT
SRUOHSETUNIM
PCOA/NPVO
CNYSVRKI
CIIMVN
ELGNUJRENUT
PDNUOSV8
)552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0(
0000000000
00
7
8
Firs
t Ti
me
Op
erat
ion
ME
NU
You
r T
V is
now
rea
dy fo
r us
e
5A
new
men
u ap
pear
s on
the
scre
en a
skin
g yo
u to
che
ck
that
the
aeri
al is
con
nect
ed. E
nsur
e th
e ae
rial
is c
onne
cted
an
d th
en p
ress
the
OK
but
ton
to s
tart
the
auto
mat
ic
tuni
ng. The
TV
sta
rts
to a
utom
atic
ally
sea
rch
and
sto
re a
ll
avai
labl
e ch
anne
ls (T
V B
road
cast
) for
you
.
Thi
s pr
oced
ure
coul
d ta
ke s
ome
min
utes
. Ple
ase
be
pati
ent a
nd d
o no
t pre
ss a
ny b
utto
n. O
ther
wis
e th
e
auto
mat
ic tu
ning
will
not
be
com
plet
ed.
6A
fter
all
avai
labl
e ch
anne
ls a
re c
apti
oned
and
sto
red
,
the
Pro
gram
me
Sor
tin
g m
enu
appe
ars
auto
mat
ical
ly
on th
e sc
reen
ena
blin
g yo
u to
cha
nge
the
ord
er in
w
hich
the
chan
nels
app
ear
on th
e sc
reen
.
a)If
you
do
not w
ish
to c
hang
e th
e ch
anne
l ord
er, g
o to
st
ep 7
.
b)
If y
ou w
ish
to c
hang
e th
e ch
anne
l ord
er:
1Pr
ess
the
orbu
tton
to s
elec
t the
pro
gram
me
num
ber
wit
h th
e ch
anne
l (T
V B
road
cast
) you
wis
h
to r
earr
ange
, the
n pr
ess
the
butt
on.
2Pr
ess
the
orbu
tton
to s
elec
t the
new
prog
ram
me
num
ber
posi
tion
for
your
sel
ecte
d
chan
nel (
TV
Bro
adca
st),
then
pre
ss
.
3R
epea
t ste
ps b
)1 a
nd b
)2 if
you
wis
h to
cha
nge
the
ord
er o
f the
oth
er c
hann
els.
7Pr
ess
the
ME
NU
but
ton
to r
emov
e th
e m
enu
from
the
sc
reen
.M
EN
U
Ple
ase
conf
irm th
atae
rial i
s co
nnec
ted
Con
firm
OK
Pro
gram
me:
01
Sys
tem
:
B/G
Cha
nnel
:
C
21
Aut
o Tu
ning
Sea
rchi
ng...
Pro
gram
me
Sor
ting
Sel
ect c
hann
el:
Exi
t:
ME
NU
Pro
gram
me:
01
T
VE
02
T
VE
2
03
TV
3
04
C33
05
C
27
06
C
58
OK
Pro
gram
me
Sor
ting
Sel
ect n
ew p
ositi
on:
Exi
t:
ME
NU
Pro
gram
me:
01
T
VE
02
T
VE
2
03
TV
3
04
C33
05
C
27
06
C
58
05
C
27
OK
K KK
7
GB
Lang
uage
Sel
ect L
angu
age:
Eng
lish
Esp
añol
Fra
nçai
s I
talia
no M
agya
r N
eder
land
s
OK
Cou
ntry
Sel
ect c
ount
ry:
- Бъ
лгa
pия
Čes
ká r
ep.
Mag
yaro
rszá
g P
olsk
a R
omân
ia
OK
Do
you
wan
t to
star
t au
tom
atic
tuni
ng?
Yes
No
OK
K KK
Sw
itch
ing
On
th
e T
V a
nd
Au
tom
ati
call
y T
un
ing
The
firs
t tim
e yo
u sw
itch
on
your
TV
, a s
eque
nce
of m
enu
scre
en a
ppea
r on
the
TV
ena
blin
g yo
u to
: 1) c
hoos
e th
e la
ngua
ge o
f the
men
u sc
reen
, 2) c
hoos
e th
e co
untr
y in
whi
ch y
ou w
ish
to o
pera
te th
e T
V, 3
) sea
rch
and
sto
re a
ll av
aila
ble
chan
nels
(TV
Bro
adca
st) a
nd 4
) cha
nge
the
ord
er in
whi
ch th
e ch
anne
ls (T
V B
road
cast
) app
ear
on th
e sc
reen
.H
owev
er, i
f you
nee
d to
cha
nge
the
lang
uage
men
u, c
hang
e or
repe
at th
e tu
ning
(e.g
. whe
n yo
u m
ove
hous
e) o
r re
arra
nge
agai
n th
e or
der
of t
he c
hann
els
afte
rwar
ds,
you
can
do
that
by
sel
ecti
ng th
e ap
prop
riat
e m
enu
in th
e (S
et U
p). F
or m
ore
info
rmat
ion,
ref
er to
the
“Men
u G
uid
e” s
ecti
on o
f thi
s in
stru
ctio
n m
anua
l. Y
ou c
an a
lso
do
that
by
pres
sing
the
Aut
o St
art U
p B
utto
n
on
the
TV
set
.
Firs
t Ti
me
Op
erat
ion
cont
inue
d...
1
Con
nect
the
TV
plu
g to
the
mai
ns s
ocke
t (22
0-24
0V A
C,
50H
z)Pr
ess
the
on/
off b
utto
n on
the
TV
set
to tu
rn o
n th
e T
V.
The
firs
t tim
e yo
u pr
ess
this
but
ton,
a L
angu
age
men
u d
ispl
ays
auto
mat
ical
ly o
n th
e T
V s
cree
n.
2
Pres
s th
e or
butt
on o
n th
e re
mot
e co
ntro
l to
sele
ct
the
lang
uage
, the
n pr
ess
the
OK
but
ton
to c
onfi
rm y
our
sele
ctio
n. F
rom
now
on
all t
he m
enus
will
app
ear
in th
e se
lect
ed la
ngua
ge.
3
The
Cou
ntr
y
men
u ap
pear
s au
tom
atic
ally
on
the
TV
sc
reen
. Pre
ss th
e or
butt
on to
sel
ect t
he c
ount
ry in
w
hich
you
will
ope
rate
the
TV
set
, the
n pr
ess
the
OK
bu
tton
to c
onfi
rm y
our
sele
ctio
n.
Sele
ct “
-“ in
stea
d o
f a c
ount
ry
• If
the
coun
try
in w
hich
you
wan
t to
use
the
TV
set
doe
s no
t app
ear
in th
e lis
t.•
If y
ou d
o no
t wan
t you
r ch
anne
ls (T
V B
road
cast
)
st
ored
in a
giv
en c
hann
el s
eque
nce
star
ting
from
prog
ram
me
posi
tion
1.
4
The
Au
to T
un
ing
men
u ap
pear
s on
the
scre
en. P
ress
the
OK
butt
on to
sel
ect
Yes
.
The
ope
ratin
g in
stru
ctio
ns m
entio
ned
here
are
par
tial a
bstr
acts
fro
m t
he ‘O
pera
ting
Inst
ruct
ion
Man
ual’.
The
pag
e nu
mbe
rs o
f th
e ‘O
pera
ting
Inst
ruct
ion
Man
ual’
rem
ain
as in
the
man
ual.
SECTION 1 GENERAL
8
9
GB
Intr
od
uci
ng
an
d U
sin
g t
he M
en
u S
yst
em
You
r T
V u
ses
an o
n-sc
reen
men
u sy
stem
to g
uid
e yo
u th
roug
h th
e op
erat
ions
. Use
the
follo
win
g bu
tton
s on
the
Rem
ote
Con
trol
to o
pera
te th
e m
enu
syst
em:
1Pr
ess
the
ME
NU
but
ton
to s
wit
ch th
e fi
rst l
evel
men
u on
.M
EN
U
Men
u S
yste
m
2•
To
high
light
the
des
ired
men
u or
opt
ion,
pre
ssor
.•
To
ente
r to
the
sele
cted
men
u or
opt
ion,
pre
ss.
• T
o re
turn
to th
e la
st m
enu
or o
ptio
n, p
ress
.•
To
alte
r se
ttin
gs o
f you
r se
lect
ed o
ptio
n, p
ress
/
/or
.
• T
o co
nfir
m a
nd s
tore
you
r se
lect
ion,
pre
ss O
K.
3Pr
ess
the
ME
NU
but
ton
to r
emov
e th
e m
enu
from
the
scre
en.
cont
inue
d...
ME
NUK
Men
u G
uid
e
PIC
TUR
E A
DJU
STM
ENT
The
“Pi
ctur
e A
dju
stm
ent”
men
u al
low
s yo
u to
al
ter
the
pict
ure
adju
stm
ents
.
To
do
that
: aft
er s
elec
ting
the
item
you
wan
t to
alte
r pre
ss, t
hen
pres
s re
peat
edly
//
orto
ad
just
it a
nd fi
nally
pre
ss O
K to
st
ore
the
new
ad
just
men
t.T
his
men
u al
so a
llow
s yo
u to
cus
tom
ise
the
pict
ure
mod
e ba
sed
on
the
prog
ram
me
you
are
wat
chin
g: P
erso
nal
(for
ind
ivid
ual s
etti
ngs)
. L
ive
(for
live
bro
adca
st p
rogr
amm
es).
Mo
vie
(for
film
s).
Leve
l 1
Leve
l 2
Leve
l 3 /
Fu
nct
ion
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
•B
righ
tnes
s, C
olou
r an
d Sh
arpn
ess
can
only
be
alte
rate
d if
“Per
sona
l” m
ode
is s
elec
ted.
•H
ue is
onl
y av
aila
ble
for
NT
SC c
olou
r si
gnal
(e.g
: USA
vid
eo ta
pes)
.•
Sele
ct R
eset
and
pre
ss O
K to
res
et th
e pi
ctur
e to
the
fact
ory
pres
et le
vels
.
10M
enu
Sys
tem
SLEE
P TI
MER
The
“Sl
eep
Tim
er”
opti
on in
the
“Tim
er”
men
u al
low
s yo
u to
sel
ect a
tim
e pe
riod
for
the
TV
to
swit
ch it
self
aut
omat
ical
ly in
to th
e st
and
by
mod
e.
To
do
that
: aft
er s
elec
ting
the
opti
on p
ress
, th
en p
ress
orto
set t
he ti
me
peri
od d
elay
(m
ax. o
f 4 h
ours
) and
fina
lly p
ress
OK
to s
tore
. •
Whi
le w
atch
ing
the
TV
, you
can
pre
ss th
e
butt
on o
n th
e re
mot
e co
ntro
l to
disp
lay
the
ti
me
rem
aini
ng.
•O
ne m
inut
e be
fore
the
TV
sw
itch
es it
self
into
st
andb
y m
ode,
the
tim
e re
mai
ning
is d
ispl
ayed
on
th
e T
V s
cree
n au
tom
atic
ally
.
ON
TIM
ERT
he “
On
Tim
er”
opti
on in
the
“Tim
er”
men
u al
low
s yo
u to
sel
ect a
tim
e pe
riod
for
the
TV
to
swit
ch it
self
aut
omat
ical
ly o
n fr
om s
tand
by
mod
e.
To
do
that
: aft
er s
elec
ting
the
opti
on p
ress
,
then
pre
ssor
to se
t the
tim
e pe
riod
del
ay
(max
. 12
hour
s) a
nd p
ress
OK
to s
tore
. Fin
ally
pr
ess
the
stan
dby
but
ton
on
the
rem
ote
cont
rol.
Aft
er th
e se
lect
ed le
ngth
of t
ime
the
TV
sw
itch
es o
n au
tom
atic
ally
.
•T
he s
tand
by in
dica
tor
on th
e T
V s
et fl
ashe
s
regu
larl
y to
indi
cate
that
“O
n T
imer
” is
act
ive.
•
Any
loss
of p
ower
will
cau
se th
ese
sett
ings
to b
e
clea
red.
LAN
GU
AG
E /
CO
UN
TRY
The
“L
angu
age/
Cou
ntry
” op
tion
in th
e “S
et
Up”
men
u al
low
s yo
u to
sel
ect t
he la
ngua
ge
that
the
men
us a
re d
ispl
ayed
in. I
t als
o al
low
s yo
u to
sel
ect t
he c
ount
ry in
whi
ch y
ou w
ish
to
oper
ate
the
TV
set
.
To
do
that
: aft
er s
elec
ting
the
opti
on, p
ress
an
d th
en p
roce
ed in
the
sam
e w
ay a
s in
the
step
s 2
and
3 o
f the
sec
tion
“Sw
itch
ing
On
the
TV
and
Aut
omat
ical
ly T
unin
g”.
Leve
l 1
Leve
l 2
Leve
l 3 /
Fu
nct
ion
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Tim
er
Sle
ep T
imer
:
O
ff
On
Tim
er:
O
ff
OK
Tim
er
Sle
ep T
imer
:
O
ff
On
Tim
er:
O
ff OK
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Tim
er
Sle
ep T
imer
:
O
ff
On
Tim
er:
i O
ff
OK
Tim
er
Sle
ep T
imer
:
O
ff
On
Tim
er:
O
ff OK
cont
inue
d...
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
9
11
GB
Men
u S
yste
m
cont
inue
d...
AU
TO T
UN
ING
The
“A
uto
Tun
ing”
opt
ion
in th
e “S
et U
p”
men
u al
low
s yo
u to
aut
omat
ical
ly s
earc
h fo
r an
d s
tore
all
avai
labl
e T
V c
hann
els.
To
do
that
: aft
er s
elec
ting
the
opti
on, p
ress
an
d th
en p
roce
ed in
the
sam
e w
ay a
s in
TV
st
eps
4 an
d 5
of t
he s
ecti
on “
Swit
chin
g O
n th
e T
V a
nd A
utom
atic
ally
Tun
ing”
.
PRO
GR
AM
ME
SOR
TIN
GT
he “
Prog
ram
me
Sort
ing”
opt
ion
in th
e “S
et
Up”
men
u al
low
s yo
u to
cha
nge
the
ord
er in
w
hich
the
chan
nels
(TV
Bro
adca
st) a
ppea
r on
th
e sc
reen
.
To
do
that
: aft
er s
elec
ting
the
opti
on, p
ress
and
then
pro
ceed
in th
e sa
me
way
as
in s
tep
6 b)
of
the
sect
ion
“Sw
itch
ing
On
the
TV
and
A
utom
atic
ally
Tun
ing”
.
MA
NU
AL
PRO
GR
AM
ME
PRES
ETT
he “
Man
ual P
rogr
amm
e Pr
eset
” op
tion
in th
e “S
et U
p” m
enu
allo
ws
you
to:
a) P
rese
t cha
nnel
s or
a v
ideo
inpu
t sou
rce
one
b
y on
e to
the
prog
ram
me
ord
er o
f you
r
cho
ice.
To
do
that
:
1A
fter
sel
ecti
ng th
e ”M
anua
l Pro
gram
me
Pres
et”
opti
on, p
ress
then
wit
h P
rogr
amm
e op
tion
hig
hlig
hted
pre
ss.
Pres
sor
to s
elec
t on
whi
chpr
ogra
mm
e nu
mbe
r yo
u w
ant t
o pr
eset
the
ch
anne
l (fo
r V
CR
, sel
ect p
rogr
amm
e nu
mbe
r
“0”)
. The
n pr
ess
.
2A
fter
sel
ecti
ng th
e S
yste
m o
ptio
n, p
ress
.
The
n pr
ess
orto
sel
ect t
he T
V
Bro
adca
st s
yste
m (B
/G fo
r w
este
rn E
urop
ean
co
untr
ies
or D
/K fo
r ea
ster
n E
urop
ean
coun
trie
s). T
hen
pres
s .
Leve
l 1
Leve
l 2
Leve
l 3 /
Fu
nct
ion
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Man
ual P
rogr
amm
e P
rese
t
Pro
gram
me:
S
yste
m:
C
hann
el:
L
abel
:
A
FT:
S
kip:
Dec
oder
:
C
onfir
m
OK
01 B/G
C 2
1--
TV
EO
nN
oO
ff
12M
enu
Sys
tem
cont
inue
d...
3A
fter
sel
ecti
ng th
e C
han
nel
opt
ion,
pre
ss
.
The
n pr
ess
orto
sel
ect t
he c
hann
eltu
ning
(“C
” fo
r ter
rest
rial
cha
nnel
s or
“S
” fo
r ca
ble
chan
nels
). N
ext p
ress
. Aft
er th
at,
pres
s the
num
ber b
utto
ns to
ent
er d
irec
tly
the
chan
nel n
umbe
r of
the
TV
Bro
adca
st o
r th
e ch
anne
l of t
he V
CR
sig
nal.
If y
ou d
o no
t kn
ow th
e ch
anne
l num
ber,
pre
ssor
to
sear
ch fo
r it
. Whe
n yo
u tu
ne th
e d
esir
ed
chan
nel,
pres
s O
K tw
ice
to s
tore
.
Rep
eat a
ll th
e ab
ove
step
s to
tune
and
sto
re m
ore
chan
nels
.
b)N
orm
ally
the
auto
mat
ic fi
ne tu
ning
(AFT
) is
oper
atin
g, h
owev
er y
ou c
an m
anua
lly fi
ne
tune
the
TV
to o
btai
n a
bett
er p
ictu
rere
cept
ion
in th
e ca
se th
at th
e pi
ctur
e is
dis
tort
ed.
To
do
that
: whi
le w
atch
ing
the
chan
nel (
TV
B
road
cast
) you
wis
h to
fine
tune
, sel
ect t
he
AFT
opt
ion
and
pre
ss. N
ext p
ress
or
to a
dju
st th
e fi
ne tu
ning
bet
wee
n -1
5 an
d +
15. F
inal
ly p
ress
OK
twic
e to
sto
re.
c) S
kip
any
unw
ante
d p
rogr
amm
e nu
mbe
rs
whe
n th
ey a
re s
elec
ted
wit
h th
e PR
OG
R +
/-
butt
ons.
To
do
that
: Hig
hlig
htin
g th
e P
rogr
amm
e
opti
on, p
ress
the
PR
OG
R +
/- b
utto
n to
sel
ect
the
prog
ram
me
num
ber
you
wan
t to
skip
. W
hen
the
prog
ram
me
you
wan
t to
skip
appe
ars
on th
e sc
reen
, sel
ect t
he S
kip
opt
ion
and
pre
ss
. Nex
t pre
ssor
to s
elec
t Y
es. F
inal
ly p
ress
OK
twic
e to
con
firm
and
st
ore.
To
canc
el th
is fu
ncti
on a
fter
war
ds, s
elec
t “N
o”
inst
ead
of “
Yes
” in
the
step
abo
ve.
d) L
abel
a c
hann
el u
sing
up
to fi
ve c
hara
cter
s.
To
do
that
: Hig
hlig
htin
g th
e P
rogr
amm
e op
tion
, pre
ss th
e P
RO
GR
+/-
but
ton
to s
elec
t th
e pr
ogra
mm
e nu
mbe
r w
ith
the
chan
nel
you
wis
h to
nam
e. W
hen
the
prog
ram
me
you
wan
t to
nam
e ap
pear
s on
the
scre
en, s
elec
t th
e L
abel
opt
ion
and
pre
ss. N
ext
pres
sor
to s
elec
t a le
tter
, num
ber
or
“-“
for
a bl
ank.
Pre
ss
to c
onfi
rm th
is
char
acte
r. S
elec
t the
oth
er fo
ur c
hara
cter
s in
th
e sa
me
way
. Aft
er s
elec
ting
all
the
char
acte
rs, p
ress
OK
twic
e to
sto
re.
Leve
l 1
Leve
l 2
Leve
l 3 /
Fu
nct
ion
Pic
ture
Adj
ustm
ent
Mod
e: P
erso
nal
C
ontr
ast
B
right
ness
C
olou
r
Sha
rpne
ss
Hue
R
eset
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Set
Up
Lan
guag
e/C
ount
ry A
uto
Tuni
ng P
rogr
amm
e S
ortin
g M
anua
l Pro
gram
me
Pre
set
Adv
ance
d F
eatu
res
OK
Man
ual P
rogr
amm
e P
rese
t
Pro
gram
me:
S
yste
m:
C
hann
el:
L
abel
:
A
FT:
S
kip:
Dec
oder
:
C
onfir
m
OK
01 B/G
C 2
1--
TV
EO
nN
oO
ff
10
15
GB
Tele
text
Tel
etex
t is
an in
form
atio
n se
rvic
e tr
ansm
itte
d b
y m
ost T
V s
tati
ons.
The
ind
ex p
age
of th
e
tele
text
ser
vice
(usu
ally
pag
e 10
0) g
ives
you
info
rmat
ion
on h
ow to
use
the
serv
ice.
To
op
erat
e te
lete
xt, u
se th
e re
mot
e co
ntro
l but
tons
as
ind
icat
ed b
elow
.
Mak
e su
re to
use
a c
hann
el (T
V B
road
cast
) wit
h a
stro
ng s
igna
l, ot
herw
ise
tele
text
err
ors
m
ay o
ccur
.
To S
wit
ch O
n T
elet
ext
: A
fter
sel
ect t
he c
hann
el (T
V B
road
cast
) whi
ch c
arri
es th
e te
lete
xt y
ou w
ish
to v
iew
, pre
ss
.
To S
elec
t a
Tele
text
pag
e:In
put 3
dig
its
for
the
page
num
ber,
usi
ng th
e nu
mbe
red
but
tons
.•
If y
ou h
ave
mad
e a
mis
take
, ret
ype
the
corr
ect p
age
num
ber.
• If
the
coun
ter
on th
e sc
reen
con
tinu
es s
earc
hing
, it i
s be
caus
e th
is p
age
is n
ot a
vaila
ble.
In th
at c
ase,
inpu
t ano
ther
pag
e nu
mbe
r
To a
cces
s th
e n
ext
or
pre
ced
ing
pag
e:Pr
ess
PR
OG
R +
() o
r P
RO
GR
- (
).
To s
up
erim
po
se t
elet
ext
on
to
th
e TV
:W
hils
t you
are
vie
win
g te
lete
xt, p
ress
. P
ress
it a
gain
to c
ance
l tel
etex
t mod
e.
To f
reez
e a
tele
text
pag
e:So
me
tele
text
pag
es h
ave
sub-
page
s w
hich
follo
w o
n au
tom
atic
ally
. To
stop
them
, pre
ss
/. P
ress
it a
gain
to c
ance
l the
free
ze.
To r
evea
l co
nce
aled
info
rmat
ion
(e.
g: a
nsw
er t
o a
qu
iz):
Pres
s /
. Pre
ss it
aga
in to
con
ceal
the
info
rmat
ion.
To S
wit
ch O
ff T
elet
ext:
Pr
ess
.
Fast
ext
Fast
ext s
ervi
ce le
ts y
ou a
cces
s pa
ges
wit
h on
e bu
tton
pus
h.W
hile
you
are
in T
elet
ext m
ode
and
Fas
text
is b
road
cast
, a c
olou
r co
ded
men
u ap
pear
s at
th
e bo
ttom
of t
he te
lete
xt p
age.
Pre
ss th
e co
lour
but
ton
(red
, gre
en, y
ello
w o
r blu
e) to
acc
ess
th
e co
rres
pond
ing
page
.
Tele
text
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
TELE
TEX
TIn
dex
Prog
ram
me
New
sSp
ort
Wea
ther
25 153
101 98
16
Co
nn
ect
ing
Op
tio
nal
Eq
uip
men
tU
sing
the
follo
win
g in
stru
ctio
ns, y
ou c
an c
onne
ct a
wid
e ra
nge
of o
ptio
nal e
quip
men
t to
yo
ur T
V s
et. (
Con
nect
ing
cabl
es a
re n
ot s
uppl
ied
).
Con
nec
tin
g a
VC
R:
To
conn
ect a
VC
R, p
leas
e re
fer
toth
e se
ctio
n “C
onne
ctin
g th
eae
rial
and
VC
R”
of th
is in
stru
ctio
n m
anua
l. W
e re
com
men
d y
ou
conn
ect y
our
VC
R u
sing
a s
cart
le
ad. I
f you
do
not h
ave
a sc
art
lead
, tun
e in
the
VC
R te
st s
igna
l to
TV
pro
gram
me
num
ber
“0”.
by
usi
ng “
Man
ual P
rogr
amm
e Pr
eset
” op
tion
. (fo
r d
etai
ls h
ow
to m
anua
l pro
gram
me,
see
pag
e 11
, ste
p a)
.A
lso
refe
r to
you
r V
CR
in
stru
ctio
n m
anua
l to
find
out
how
to fi
nd th
e ou
tput
cha
nnel
of
you
r V
CR
.
If y
ou h
ave
con
nec
ted
a d
ecod
erto
a V
CR
wh
ich
su
pp
orts
Sm
artl
ink
fea
ture
:Se
lect
the
“Man
ual P
rogr
amm
e Pr
eset
” op
tion
in th
e “S
et U
p” m
enu
and
aft
er e
nter
ing
in th
e “D
ecod
er*”
opt
ion,
sel
ect “
On”
(by
usin
gor
) to
each
scr
ambl
ed c
hann
el.
*Thi
s op
tion
is o
nly
avai
labl
e d
epen
din
g th
e co
untr
y yo
u ha
ve s
elec
ted
in th
e “C
ount
ry”
men
u.
** “
Pla
ySta
tion
” is
a p
rod
uct o
f Son
y C
ompu
ter
Ent
erta
inm
ent,
Inc.
** “
Pla
ySta
tion
” is
a tr
adem
ark
of S
ony
Com
pute
r E
nter
tain
men
t, In
c.
Usi
ng
Op
tio
nal
Eq
uip
men
t1
Con
nect
you
r eq
uipm
ent t
o th
e d
esig
nate
d T
V s
ocke
t, as
ind
icat
ed a
bove
.
2T
o w
atch
the
pict
ure
of th
e co
nnec
ted
equ
ipm
ent,
pres
s th
e b
utto
n re
peat
edly
unt
il th
e
corr
ect i
nput
sym
bol a
ppea
rs o
n th
e sc
reen
.
Sym
bo
lIn
pu
t Si
gn
als
1
•A
udio
/ v
ideo
inpu
t sig
nal t
hrou
gh th
e Sc
art c
onne
ctor
C
•R
GB
inpu
t sig
nal t
hrou
gh th
e Sc
art c
onne
ctor
C. T
his
sym
bol a
ppea
rs o
nly
if
a R
GB
sou
rce
has
been
con
nect
ed.
2
•V
ideo
inpu
t sig
nal t
hrou
gh th
e ph
ono
sock
et A
and
Aud
io in
put s
igna
l
thro
ugh
B.
3Sw
itch
on
the
conn
ecte
d e
quip
men
t.
4Pr
ess
but
ton
on th
e re
mot
e co
ntro
l to
retu
rn to
the
norm
al T
V p
ictu
re.
AB
12
C
8mm
/H
i8/
DV
Cca
mco
rder
Ad
dit
ion
al In
form
atio
n
“Pla
ySta
tion
”**
VC
R
Dec
oder
11
18
Tro
ub
lesh
oo
tin
g H
ere
are
som
e si
mpl
e so
luti
ons
to th
e pr
oble
ms
whi
ch m
ay a
ffec
t the
pic
ture
and
sou
nd.
Ad
dit
ion
al In
form
atio
n
Pro
ble
m
No
pict
ure
(scr
een
is d
ark)
and
no
soun
d.
Poor
or
no p
ictu
re (s
cree
n is
dar
k),
but g
ood
sou
nd.
No
pict
ure
or n
o m
enu
info
rmat
ion
from
the
equi
pmen
t con
nect
ed to
the
Scar
t con
nect
or.
Goo
d p
ictu
re, n
o so
und
.
No
colo
ur o
n co
lour
pro
gram
mes
.
Dis
tort
ed p
ictu
re w
hen
chan
ging
pr
ogra
mm
es o
r se
lect
ing
tele
text
.
Pict
ure
slan
ted
(onl
y fo
r K
V-2
1LT
1K)
Noi
sy p
ictu
re w
hen
view
ing
a T
V
chan
nel.
Rem
ote
cont
rol d
oes
not f
unct
ion.
The
sta
ndby
ind
icat
or
on
the
TV
fl
ashe
s ev
en th
ough
the
“On
Tim
er”
Solu
tio
n
•C
heck
the
aeri
al c
onne
ctio
n.•
Plu
g th
e T
V in
and
pre
ss th
e b
utto
n on
the
fron
t of
T
V.
•If
the
stan
dby
ind
icat
or
is o
n, p
ress
b
utto
n on
th
e re
mot
e co
ntro
l.
•U
sing
the
men
u sy
stem
, sel
ect t
he “
Pict
ure
Ad
just
men
t” m
enu
and
sel
ect “
Res
et”
to r
etur
n to
the
fa
ctor
y se
ttin
gs.
•C
heck
that
the
opti
onal
equ
ipm
ent i
s on
and
pre
ss th
e
but
ton
repe
ated
ly o
n th
e re
mot
e co
ntro
l unt
il th
e
corr
ect i
nput
sym
bol i
s d
ispl
ayed
on
the
scre
en.
• P
ress
the
+
/- b
utto
n on
the
rem
ote
cont
rol.
• U
sing
the
men
u sy
stem
, sel
ect t
he “
Pict
ure
Ad
just
men
t” m
enu
and
sel
ect “
Res
et”
to r
etur
n to
fa
ctor
y se
ttin
gs.
• T
urn
off a
ny e
quip
men
t con
nect
ed to
the
Scar
t
conn
ecto
r on
the
rear
of t
he T
V.
• U
sing
the
men
u sy
stem
, sel
ect t
he “
Pict
ure
Rot
atio
n”
opti
on in
the
“Ad
vanc
ed F
eatu
res”
men
u to
cor
rect
the
pi
ctur
e sl
ant.
• U
sing
the
men
u sy
stem
, sel
ect t
he “
Man
ual
Prog
ram
me
Pres
et”
men
u an
d a
dju
st F
ine
Tun
ing
(A
FT) t
o ob
tain
bet
ter
pict
ure
rece
ptio
n.•
Usi
ng th
e m
enu
syst
em, s
elec
t the
“N
oise
Red
ucti
on”
op
tion
in th
e “A
dva
nced
Fea
ture
s” m
enu
and
sel
ect
“O
n” to
red
uce
the
nois
e in
the
pict
ure.
• R
epla
ce th
e ba
tter
ies.
• C
onta
ct to
you
r ne
ares
t Son
y se
rvic
e ce
ntre
.
In c
ase
of p
robl
ems,
hav
e yo
ur T
V s
ervi
ced
by
qual
ifie
d p
erso
nnel
. Nev
er o
pen
the
casi
ng y
ours
elf.
12
SECTION 2 DISASSEMBLY
2-3. A Board PWB Removal [ Step 2 ]
2-2. A Board PWB Removal [ Step 1 ]
2-5. Wire Dressing
Ensure that all wires do not touch heat-sinks and hightemperature hot spots. All wires must be kept at a minimumdistance of 20mm away from the EHT lead.
2-1. Rear Cover Removal
2-4. Service Position
Release the mains power cable from its securing posts.Remove the rear cover fixing screws indicated. Pull the rearcover away from the front beznet until clear of chassis.
Note : Use a cross-head screwdriver with a blade length of atleast 200mm.
KV-21LT1
Remove screw.<=
Remove FBTsupport bracket.
<=
Release the 2 securingclips located at eitherside of the chassis andslide the PWB clear ofthe bracket.
<=
Place the A Board PWB in theposition indicated to carry outservicing.
=>
=> <=
<=
13
Anode button
a
* REMOVING PROCEDURES.
Turn up one side of the rubber cap inthe direction indicated by the arrow a
1 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b
3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c
b
b
c
How to handle the Anode-Cap
1. To prevent damaging the surface of the anode-cap do not usesharp materials.
2. Do not apply too great a pressure on the rubber, as this may causedamage to the anode connector.
3. A metal fitting called a shatter hook terminal is fitted inside therubber cap.
4. Do not turn the rubber foot over excessively, this may cause damageif the shatter hook sticks out.
Removal of the Anode-Cap
2-6. Picture Tube Removal
WARNING:BEFORE REMOVING
THE ANODE CAP
High voltage remains in the CRT evenafter the power is disconnected. Toavoid electric shock, discharge CRTbefore attempting to remove the anodecap. Short between anode and CRTcoated earth ground strap.
Coated EarthGround Strap
1. Discharge the anode of the CRT and remove the anode cap.2. Release the EHT lead from its CRT support bracket.3. Unplug all interconnecting leads from the Deflection yoke,
degaussing coils and CRT grounding strap.4. Remove the C Board from the CRT.5. Remove the chassis assembly.6. Loosen the Deflection yoke fixing screw and remove.7. Place the set with the CRT face down on a cushion.8. Unscrew the four CRT fixing screws [ located on each CRT
corner ] and remove the CRT.9. Remove the Degaussing Coils.
Remove the CRT grounding strap and spring tentioners.[Take care not to handle the CRT by the neck.]
1
3
4
2
5
6
7
8
9
14
Remove the rear cover fixing screws indicated. Pull the rearcover straight back until clear of chassis.
2-7. Rear Cover Removal
To remove the chassis release the clips indicated at oppositesides of the main bracket and slide the chassis away from thebeznet. Ensure that the interconnecting leads are released fromtheir purse locks to prevent damage being caused.
Position the A board as shown to gain access to its solder side.Take care not to trap the interconnecting leads in the process.
2-9. Service Position
2-8. Chassis Removal and Refitting
2-10. Wire Dressing
Ensure that all wires do not touch heat-sinks and high tempera-ture hot spots. All wires must be kept at a minimum distance of20mm away from the EHT lead.
KV-21FT2
=>
=>
=> =>
=>
=>
=>
15
Anode button
a
* REMOVING PROCEDURES.
Turn up one side of the rubber cap inthe direction indicated by the arrow a
1 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b
3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c
b
b
c
How to handle the Anode-Cap
1. To prevent damaging the surface of the anode-cap do not usesharp materials.
2. Do not apply too great a pressure on the rubber, as this may causedamage to the anode connector.
3. A metal fitting called a shatter hook terminal is fitted inside therubber cap.
4. Do not turn the rubber foot over excessively, this may cause damageif the shatter hook sticks out.
Removal of the Anode-Cap
2-11. Picture Tube Removal
WARNING:BEFORE REMOVING
THE ANODE CAP
High voltage remains in the CRT evenafter the power is disconnected. Toavoid electric shock, discharge CRTbefore attempting to remove the anodecap. Short between anode and CRTcoated earth ground strap.
Coated EarthGround Strap
1. Discharge the anode of the CRT and remove the anode cap.2. Unplug all interconnecting leads from the Deflection yoke, neck
assy, degaussing coils and CRT grounding strap.3. Remove the C Board from the CRT.4. Remove the chassis assembly.5. Loosen the Deflection yoke fixing screw and remove.6. Place the set with the CRT face down on a cushion and remove
the Degaussing Coil holders.7. Remove the Degaussing Coils.8. Remove the CRT grounding strap and spring tentioners.9. Unscrew the four CRT fixing screws [ located on each CRT
corner ] and remove the CRT.[Take care not to handle the CRT by the neck.]
1
3
5
2
4
8
7
6
9
16
Purity control correctsthis area
Disk magnets orrotatable diskmagnets correctthese areas (a-d)
Deflection yoke positioningcorrects these areas
a
c d
b
Disk Magnets
GREEN
BLUERED
Preparation:1. In order to reduce the influence of geomagnetism on the
set’s picture tube, face it in an easterly or westerly direction.2. Switch on the set’s power and degauss with the degausser.
1. Input an all white signal from the pattern generator. Set theContrast and Brightness to normal.
2. Set the pattern generator raster signal to Red.3. Move the deflection yoke forward and adjust with the
purity control so that the Red is at the centre and the Blueand Green take up equally sized areas on each side of thescreen. [See Fig.3-1 - 3-3].
4. Move the deflection yoke backwards and adjust so that theentire screen becomes Red. [See Fig.3-1]
5. Switch the raster signal to Blue, then to Green and verifythe condition.
6. When the position of the deflection yoke has beendetermined, fasten the deflection yoke with the screws.
7. If the beam does not land correctly in all the corners, use amagnet to correct it. [See Fig.3-4]
• When complete readjustment is necessary or a new picturetube is installed, carry out the following adjustments.
• Unless there are specific instructions to the contrary, carryout these adjustments with the rated power supply.
• Unless there are specific instructions to the contrary, set thecontrols and switches to the following settings :
Contrast .................... 80% [or remote control normal]
Brightness ................... 50%
Carry out the adjustments in the following order :3-1. Beam Landing.3-2. Convergence.3-3. Focus.3-4. White Balance.
Note : Test equipment required.1. Color bar/pattern generator.2. Degausser.3. Oscilloscope.4. Digital multimeter.
SECTION 3 SET-UP ADJUSTMENTS
3-1. Beam Landing
Caution :
High voltages are present on the Deflection yoke terminals- take care when handling the Deflection yoke whilst carryingout adjustments.
Fig.3-4
Fig. 3-1.
Fig. 3-3.
Fig. 3-2. Purity
17
4. If the V.STAT magnet is moved in the direction of the (a)and (b) arrows, the Red, Green and Blue points move as
indicated below.
3-2. Convergence
1. [Moving horizontally], adjust the H.STAT control so thatthe Red, Green and Blue points are on top of each other atthe centre of the screen.
2. [Moving vertically], adjust the V.STAT magnet so that theRed, Green and Blue points are on top of each other at thecentre of the screen.
3. If the H.STAT variable resistor is unable to bring the Red,Green and Blue points together at the centre of the screen,adjust the horizontal convergence with the H.STAT variableresistor and the V.STAT magnet in the manner indicatedbelow.[In this case, the H.STAT variable resistor and the V.STATmagnet influence each other].
The movement of the magnets interact with each other and sothe respective dot position should be monitored while carryingout this adjustment.Use the H.STAT VR to adjust the Red, Green and Blue dots sothat they coincide at the centre of the screen(by moving the dots in the horizontal direction).
Operation of the BMC (Hexapole) magnet.
G BR G BR G BR
GBR G BR G
BR
Preparation:
� Before starting this adjustment, adjust the focus, horizontalsize and vertical size.
� Minimize the Brightness setting.
� Input a dot pattern from the pattern generator.
Horizontal and Vertical Static Convergence
Fig.3-5
� Tilt the V.STAT magnet and adjust the static convergence byopening or closing the V.STAT magnet.
V.STAT Vertical Static Magnet
H.STATconvergence
control
RV5375 (H STAT)H STAT Convergence(on mount side)
Center dot
R G B
R
G
B
B
G
R
B
G
R
a
a
b
b
a b
BGR
a
a
BGR
b
b
B
G
R
a
b
R
G
B
ba
18
If you are unable to adjust the corner convergence properly, thiscan be corrected with the use of permalloy magnets.
HTIL correction can be performed by adding a TLH correctionassembly to the Deflection yoke.
HTIL Adjustment
YCH Adjustment
TLV Adjustment
Geometry Adjustment.
Preparation:
Before starting this adjustment, adjust the horizontal and verticalstatic convergence.
1. Remove the deflection yoke spacer.2. Tilt the deflection yoke as indicated in the figure below and
optimise the geometry.Tilting the DY Up and Down will balance the upper andlower pin adjustment.Tilting the DY Left and Right will balance the H-Trapadjustment.
3. Re-install the deflection yoke spacer.
+YCH VR
Deflection Yoke
+
+
Deflection Yoke
+ TLV VR
Screen Corner Convergence
TLH pieces
Deflection Yoke
Tilt Direction
a-d: screen-cornerconvergence defect
a b
c d
a
b
d
Permalloy AssyX-4387-214-1
c
Install the permalloy assemblyfor the area that needs correcting.
Convergence adjustment with permalloy
19
3-3. Focus Adjustment
1. Receive a television broadcast signal.2. Normalize the picture setting.3. Adjust the focus control located on the flyback transformer
to obtain the best focus at the centre of the screen.Bring only the centre area of the screen into focus, themagenta-ring appears on the screen. In this case, adjust thefocus to optimize the screen uniformly.
3-4. Screen (G2), White Balance
[Adjustment in the service mode using the remotecommander]
G2 adjustment
1. Input a dot signal from the pattern generator.2. Set the Picture, Brightness and Colour to minimum.3. Apply 175V DC from an external power supply to the R, G
and B cathodes of the CRT.4. Whilst watching the picture, adjust the G2 control [SCREEN]
located on the Flyback Transformer to the point just beforethe flyback return lines disappear.
Layout of each control
1. Input an all-white signal from the pattern generator.2. Enter into the ‘Service Mode’ by pressing ‘TEST’, ‘TEST’
and ‘MENU’ on the Service Commander.3. Select ‘Service’ from the on screen menu display and press
the right arrow button on the remote commander.4. The ‘Service’ menu will appear on the screen.
[See Page 18]5. Set the ‘Contrast’ to MAX.6. Set the ‘R-Drive’ to 25.7. Adjust the ‘G-Drive’ and the ‘B-Drive’ so that the white
balance becomes optimum.8. Press the ‘OK’ button to write the data for each item.9. Set the ‘Contrast’ to MIN.10. Adjust the ‘G-Cutoff’, and the ‘R-Cutoff’ with the left and
right buttons on the remote commander so that the whitebalance becomes optimum.
11. Press the ‘OK’ button to write the data for each item.
White balance adjustment for TV mode
V.STAT
BMC (Hexapole)
Purity
Screen
Focus
20
SECTION 4 CIRCUIT ADJUSTMENTS
4-1. Electrical Adjustments
Service adjustments to this model can be performed using the suppliedRemote Commander RM-887.
How to enter into the Service Mode
‘TT—’ will appear in the upper right corner of the screen.Other status information will also be displayed.
3. Press ‘MENU’ on the remote commander to obtain the followingmenu on the screen.
4. Move to the corresponding adjustment item using theup or down arrow buttons on the Remote Commander.
5. Press the right arrow button to enter into the required menu item.6. Press the ‘Menu’ button on the Remote Commander to quit the
Service Mode when all adjustments have been completed.
Note :
• Before performing any adjustments ensure that the correct model has been selected in the ‘Model Setting’ menu.
• After carrying out the service adjustments, to prevent the customeraccessing the ‘Service Menu’ switch the TV set OFF and then ON.
i+ 5 +(ON SCREEN (DIGIT 5) (VOLUME +) (TV) DISPLAY)
TSUJDAFI
tsujdACGAetumotuA
niaGoiduAgnitaGL
)552,0()552,0()552,0()552,0(
0101
UNEMRORRE
20E30E40E50E60E70E80E90E01E11E
GNIKROWEMIT
SRUOHSETUNIM
PCOA/NPVO
CNYSVRKI
CIIMVN
ELGNUJRENUT
PDNUOSV8
)552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0()552,0(
0000000000
00
1. Turn on the main power switch and enter into the stand-by mode.2. Press the following sequence of buttons on the Remote
Commander.
yrtemoeGecivreS
ngiseDsutatS
tsujdaFIuneMrorrE
21.1vonoM2-EFh00h00atadyrotcaF
ECIVRES
R-tesffOG-tesffOevirD-RevirD-GevirD-B
qerF-kaePyaleD-amuL
0CSkaeP-etihW
tnocbuSthgirbuS
locbuSprahsbuS
DSOrBTXTrB
)51,0()51,0()36,0()36,0()36,0(
)3,0()51,0(
)3,0()51,0()51,0()36,0()36,0()36,0()51,0()51,0(
jdAjdA
52jdAjdA
08351
jdAjdAjdA
13118
YRTEMOEG
klBH-tfeLklBH-thgiR
elgnA-VwoB-V
ertneC-HeziS-H
pmA-niPniP-renroC-UniP-renroC-L
esahPniPytiraeniL-V
eziS-VnoitcerroC-S
ertneC-VmooZ-V
)51,0()51,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0(
319
jdAjdAjdAjdAjdAjdAjdAjdAjdAjdAjdAjdA
52
21
Deflection System Adjustment
Sub Brightness Adjustment
1. Input a Monoscope pattern.2. Press ‘TEST’ ‘TEST’ 13 on the Remote Commander.3. Adjust the ‘Sub-Brightness’ data so that there is barely a
difference between the 0 IRE and 10 IRE signal levels.
1. Input a video signal that contains a small 100% white area on ablack background.
2. Connect an digital voltmeter to Pin 10 of J701 [C Board].3. Adjust the Sub-Contrast [‘TT11’] to obtain a voltage of
95 +0,- 5V.
Sub Contrast Adjustment
Sub Colour Adjustment
1. Receive a PAL colour bar signal.2. Connect an oscilloscope to Pin 3 of CN504 [A Board].3. Enter into the ‘Service’ service menu.4. Adjust the ‘Sub Colour’ data so that the Cyan, Magenta and
Blue colour bars are of equal levels as indicated below.Note:
Ensure that no signal is applied to the Antenna socket whilecarrying out the following IF adjustments.
Same Level
B-Out Waveform
Tuner AGC Adjustment
1. Set the “AGC adjust” register value :
• For destination France set the value to 6.• All other destinations set the value to 0.
2. Receive a signal of 64dBuV / 75 ohm terminated [62dBuV / 75ohms for B model] via the tuner antenna socket.
3. Connect a voltmeter to pin1 of TU101 [print side of A Board] orto the AGC pin of CN001 [mount side of A Board].
4. Confirm that the AGC voltage is 3.5volts +/- 0.3volts.5. If adjustment is required, enter into the ‘Test Menu’.6. Select the ‘AGC Adjust’ menu item.7. Adjust the data using the left and right arrow buttons on the
Remote Commander to obtain a voltage of 3.5V +/- 0.3V.
1. Enter into the ‘Geometry’ service menu.2. Select and adjust each item in order to obtain the optimum image.
[ Print side of A board ]
YRTEMOEG
klBH-tfeLklBH-thgiR
elgnA-VwoB-V
ertneC-HeziS-H
pmA-niPniP-renroC-UniP-renroC-L
esahPniPytiraeniL-V
eziS-VnoitcerroC-S
ertneC-VmooZ-V
)51,0()51,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0()36,0(
319
jdAjdAjdAjdAjdAjdAjdAjdAjdAjdAjdAjdA
52
22
V SIZE
V LIN
S CORRECTION
V CENTRE
H CENTRE
H SIZE
PIN AMP
PIN PHASE
CORNER PIN
V ANGLE
4-2. TEST MODE 2:
Is available by pressing the ‘TEST’ button twice, OSD ‘TT’ appears.The functions described below are available by selecting the twonumbers. To release the ‘Test mode 2’, press 00, 10, 20 ... twice orswitch the TV set into Stand-by mode. In ‘TT Menu’ mode, it ispossible to remove the Menu from the screen by pressing the SpeakerOff button once. Pressing the Speaker OFF button a second time willcause the Menu to reappear. The function is kept even when the menu isnot displayed on screen !!.
00 ffoedom'TT'
10 mumixamerutciP
20 muminimerutciP
30 %53otemuloVenohpdaeh/rekaepsteS
40 %05otemuloVenohpdaeh/rekaepsteS
50 %56otemuloVenohpdaeh/rekaepsteS
60 %08otemuloVenohpdaeh/rekaepsteS
70 edomgniegA
80 noitidnoCgnippihS
11 tnemtsujdaerutcipbuS
21 tnemtsujdaruolocbuS
31 tnemtsujdassenthgirBbuS
41 tnemtsujdanoitisoPHtxeT
51 tseTnoitatoRerutciP
61 %05levelerutciP
91 edoMyrotcaFelggoT
12 EDAnoitanitseD
22 LBnoitanitseD
32 EDAnoitanitseD
42 UnoitanitseD
52 EDAnoitanitseD
62 LBnoitanitseD
72 RKnoitanitseD
82 RKnoitanitseD
13 elbanE/elbasiDffotuSotuA
33 FFO/NOnoitatoR
53 noitcnuFoN
63 noitcnuFoN
83 tnemtsujdA2GretnE
14 )95gorP(MVNesilaitini-eR
24 )95gorP(yrtemoegesilaitini-eR
84 )95gorP(nigrivnonsaMVNteS
94 )95gorP(nigrivsaMVNteS
16 tnemtsujdaCGAotuA
36 noitcnuFoN
46 ytiroirpBGRelbasid/elbanE
56 elbasid/elbanetceted-otuaBGR
66 elbasid/elbaneremitnO
76 tnemtsujdaCGAlaunaM
86 )melborpN(erusaemretnuoc62Xelbasid/elbanE
17 )ylnOesUyrotcaF(oedivLAPecroF
27 )noitidnocoedivlamronerotser(LAPecrof-nU
78 tsetsyeklacoL
88 noitcnuFoN
98 godhctawelbasid/elbanE
99 unememiTgnikroWdnarorrEyalpsiD
23
Memo
24
5-2. CIRCUIT BOARD LOCATION
5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDSNote :• All capacitors are in µF unless otherwise noted.• pF : µµF 50WV or less are not indicated except for
electrolytic types.• Indication of resistance, which does not have one for
rating electrical power, is as follows.
Pitch : 5mmElectrical power rating : 1/4W
• Chip resistors are 1/10W• All resistors are in ohms.
k = 1000 ohms, M = 1000,000 ohms
• : nonflammable resistor.
• : fusible resistor.
• : internal component.
• : panel designation or adjustment for repair.
• All variable and adjustable resistors have characteristic curve B, unless otherwise noted.
• All voltages are in Volts.• Readings are taken with a 10Mohm digital mutimeter.• Readings are taken with a color bar input signal.• Voltage variations may be noted due to normal production
tolerences.
• : B + bus.
• : B - bus.
• : RF signal path.
• : earth - ground.
• : earth - chassis.
Reference Information
RESISTOR RN : METAL FILM
RC : SOLID
FPRD : NON FLAMMABLE CARBON
FUSE : NON FLAMMABLE FUSIBLE
RS : NON FLAMMABLE METAL OXIDE
RB : NON FLAMMABLE CEMENT
RW : NON FLAMMABLE WIREWOUND
: ADJUSTMENT RESISTOR
COIL LF-8L : MICRO INDUCTOR
CAPACITOR TA : TANTALUM
PS : STYROL
PP : POLYPROPYLENE
PT : MYLAR
MPS : METALIZED POLYESTER
MPP : METALIZED POLYPROPYLENE
ALB : BIPOLAR
ALT : HIGH TEMPERATURE
ALR : HIGH RIPPLE
Les composants identifiés par une trame etpar une marque sont d'une importancecritique pour la sécurité. Ne les remplacerque par des pièces de numéro spécifié.specified.
Note :
The components identified by shadingand marked are critical for safety.Replace only with the part numbers specified in the parts list.
Note :
CVM Board
A Board
S1 Board
VM
C
H
D1A
JA2
N
D
A1D2
C
A
2526
2728
5-2.
B
LO
CK
DIA
GR
AM
S (
1)
LOW
B
5 4 1
CN
001
J401
(1/2
)
79
63
5 7
4 32 15 4
RE
LAY
SW
ITC
HQ
601
T60
3S
RT
16 151718
18 16
1 2
15
81112
12
IC60
3E
RR
OR
AM
P
PH
601
ISO
LAT
OR
+B
D63
9R
EC
TA
UD
IOV
CC
+B
LOW
B
3.3V
RE
G
H-O
UT
Q53
3
ST
BY
+3.3
V
IC60
8
7
5
IC50
1V
OU
TP
UT
3 1
VD
+
BO
OS
T
RE
F
OU
T
PIN
OU
TQ
532
6 5 4 3 2 1
D57
1,Q
571,
574
T51
1F
BT
FV A
BL
12
341 5 6
13 8911 10 7
V D
Y
V-
DY
+
DY
AS
SY
V-
DY
-
H D
Y
H-
DY
+
H-
DY
-
V-
DY
+
V-
DY
-
H-
DY
+
H-
DY
+
TO
C B
OA
RD
CN
70
7
H1
200
V
TO
PIC
TU
RE
TU
BE
2365
+- + -
17
IC53
1P
IN C
OR
RE
CT
ION
EW
HP
PR
OT
EC
TIN
VP
VD
-
41 2
3
T53
1H
DT
IC60
9S
TA
ND
BY
PO
WE
R
HD
DC
T60
2
D63
2R
EC
T
IC00
1M
ICR
O,
VID
EO
PR
OC
ES
SO
R,
RO
M,
AU
DIO
, V
IDE
O S
WIT
CH
CN
601
CN
510
VD
VG
CH
VS
HP
+B
HV
CN
508
XT
AL
OU
T
RE
D
NV
M W
P
LED
L A
UD
IO
TO
SP
EA
KE
RS
A (
)
PO
WE
R S
UP
PLY
, D
EF
LEC
TIO
N,
SM
ALL
SIG
NA
L B
OA
RD
,A
UD
IO A
MP
LIF
IER
IC60
1
D51
4-1
5V R
EC
T
VID
EOL
+5V
ST
BY
1 2 1 3D
GC
DG
C
DG
C
DG
CC
HE
CK
DG
C C
HE
CK
CN
603
CN
602
PO
WE
R
S60
1
21
H-
DY
-
H-
DY
-
TO
C B
OA
RD
CN
706
G2
21
IC60
4D
UA
L D
C R
EG
ULA
TO
R+8
V
D11
6
D61
7
D60
8
LIN
E F
ILT
ER
T60
1R
ELA
YR
Y60
1
MA
IN R
EC
TD
601
1 3 4 6 7 9
CT
VS
EN
SE
RT
TIM
ER
SS
OC
P
12V
G(G
)
Q60
6
Q60
7
6 5 47 3
LOW
B
D62
4
D62
2
D61
8
D61
9
VM
VC
C
QC
P D
ET
EC
TQ
612,
602
14
CN
1201
J120
0
R A
UD
IO
64
XT
AL
IN
48
AU
DIO
MU
TE
5
AU
D O
UT
/CV
6520
6 672
1V
CC
OU
T
IC00
2R
EM
OT
E C
ON
TR
OL
RE
CE
IVE
R
+3.
3VS
TB
Y
6523
+- + -
71
+5V
ST
BY
IC20
1A
UD
IO A
MP
MU
TE
1IN
/INL
10
14O
UT
/L
H-D
RIV
EQ
535
FU
NC
TIO
N S
WIT
CH
S00
1 -
S00
668
IC40
1A
V L
INK
+5V
ST
BY
69
R0
58
A10
B10 1 2 3 4
G0
57
B0
56
IK55
GR
EE
N
BLU
E IK
EW
D17
VD
-18
VD
+19
AB
L54 73
TO
C B
OA
RD
CN
703
TO
C B
OA
RD
CN
1705
7
CN
504
J401
(2/2
)
NS
C C
OR
RE
CT
RO
T C
OIL
AG
C
SC
L
SD
A
VID
EO
IC00
4S
DA
6S
CL
5
7W
P
71
SC
L
72
SD
A
36C
VB
S2/
CV
BS
Y2
2K
EY
/CS
3A
GC
53B
2/U
IN
1M
OD
E1
80M
OD
E2
52G
2/Y
IN
51R
2/V
IN
46-/
C4
50IN
SS
W2
40C
VB
S1
45-/
CV
BS
4Y4
65K
EY
/CS
32A
UD
IO 1
29A
UD
IO 2
42C
VB
S3
A8
A11A7
B8
A15 A16
B20
B15
A20
A2
BLU
E IN
MO
DE
1
MO
DE
2
GR
EE
N IN
RE
D IN
C2
IN
BLK
V IN
1
Y/V
IN 2
IC00
3R
ES
ET
BU
FF
ER
Q40
1,41
1
A19
TU
101
MU
TE
SW
Q21
2
AU
DIO AU
DIO
VID
EO
ST
BY
70
2F
B
D51
3+
15V
RE
CT
5 1
G D
RIV
E,
BK
GQ
705,
706
B D
RIV
E, B
KG
Q70
8, 7
09
R O
UT
Q70
4
G O
UT
Q 7
07
B O
UT
Q71
0
H2
H1
RV
702
H S
TA
T
PIC
TU
RE
T
UB
E
5
CN
703
R G B H2
CN
707
TO
A B
OA
RD
CN
502
TO
A B
OA
RD
T51
1 (F
BT
)
HR C V
1+2
00V
R G B
H V
RC
V
G2
G 4G 2
TO
A B
OA
RD
CN
504
6 5 4
R D
RIV
E, B
KG
Q70
2, 7
03
1
CN
706
TO
T51
1 F
BT
G2
1000
V
3
CN
1801
TO
RO
TA
TIO
NC
OIL
1
3
CN
1705
TO
A B
OA
RD
CN
510
3 8
2 71
IC18
01
2930
3231
[ C
PR
INT
ED
WIR
ING
BO
AR
D ]
C [
R, G
, B O
UT
]
[ A
PR
INT
ED
WIR
ING
BO
AR
D ]
feR
)e()
b()c(
feR
)e()
b()c(
feR
)e()
b()c(
107Q
2.4218.421
202607
Q5.7
1.80.521
217Q
8.5214.621
9.102
207Q
3.20.3
5.7707
Q6.421
8.5215.5
317Q
0.3314.231
9.102
307Q
5.71.8
6.131807
Q5.3
1.25.7
517Q
3.2315.131
1.8
407Q
1314.231
2.5907
Q5.7
1.83.321
617Q
8.5210.521
1.8
507Q
5.21.3
5.7017
Q0.321
3.4215.5
717Q
2.4214.321
1.8
C b
oar
d S
emic
on
du
cto
r Vo
ltag
e Ta
ble
elbaT
egatl
oVCI o
NfeR
oN
niP
)V(
egatl
oV
1081CI
13.1
23.1
34.1
51.4
61.4
70.7
80.8
C b
oar
d I
C V
olt
age
Tab
le
A b
oard
Wav
efor
ms
1.83
Vp-
p (V
)
20
us
/div
TP
72
0u
s/d
iv
TP
6
16.8
Vp-
p (H
)
5m
s/d
iv
49.8
Vp-
p (V
)
TP
8
20
us
/div
1.86
Vp-
p (H
)
TP
32
0u
s/d
iv
6.0
Vp-
p (H
)
TP
4
20
us
/div
5.4
Vp-
p (H
)
TP
5
20
us
/div
1.84
Vp-
p (H
)
TP
22
0u
s/d
iv
1.88
Vp-
p (H
)
TP
1
5m
s/d
iv
488
mV
p-p
(V)
TP
9T
P10 1.
06 k
Vp-
p (H
)20
us
/div
5m
s/d
iv
50.8
Vp-
p (V
)
TP
11
NO
TE
:P
ort
ion
s o
f th
e ci
rcu
it m
arke
d a
s sh
ow
n a
re h
igh
volt
age
area
s. U
se c
are
to p
reve
nt
elec
tric
sh
ock
du
rin
g in
spec
tio
n o
r re
pai
r.
elbaT
egatl
oVCI
oNfe
Ro
Nni
P)
V(e
gatloV
oNfe
Ro
Nni
P)
V(e
gatloV
100CI
10
100CI
768.4
22.3
864.0
39.2
960
50
070
60.2
170
83.2
270
90.8
371.7
010.5
470.5
210
571.8
310
675.3-
410.4
770
614.1
872.3
715.1
972.3
810
080
910
105CI
13.0
028.3
36.21-
128.3
52.0
220.5
69.31
620
73.0
825.3
135CI
14.1
926.3
23.2
039.1
38.1
133.0
54.2
236.3
66.1
439.1
74.6
534.1
106CI
14.08-
639.3
25.08-
838.1
32.08-
043.3
42.08-
243.3
55.18-
344.1
66.18-
540
78.77-
640
98.18-
746.3
0167-
848.2
119.18-
943.2
214.97-
052.0
415.61
155.2
5111
255.2
614.41
355.2
814.68
451.2
1021CI
111
552.5
39.4
650.3
50
751.3
60
851.3
73.11
952.3
93.0
260
010
360
210
460
4153.11
560
feR
)e()
b()c(
feR
)e()
b()c(
310Q
07.0
0406
Q0
05.2
610Q
00
3.3806
Q0
06.5
212Q
07.0
0906
Q6.5
6.50
104Q
8.42.4
8.1
114Q
1.17.1
2.4fe
R)s(
)g(
)d(
106Q
6.58.4
3.5606
Q9.01
5.417.68
206Q
2.411.5
8706
Q4.28-
9.97-9.01
306Q
88
0535
Q0
5.22.59
ED
OID
534D
2-
A436
D01
-F
100D
2-
J634
D3
-A
936D
6-I
200D
4-
J105
D9
-D
046D
5-
L
300D
2-
J205
D9
-D
1021D
1-
H
400D
8-
M305
D1
-I3021
D4
-I
600D
8-
M405
D2
-H
4021D
4-
H
700D
2-
J505
D1
-J
CI
800D
1-
L605
D5
-D
100CI
2-
K
010D
2-
G705
D1
-J
200CI
8-
M
110D
2-
H215
D8
-D
300CI
2-I
210D
2-
J315
D9
-D
400CI
4-
K
310D
8-
M415
D9
-C
104CI
2-I
410D
8-
M435
D4
-D
105CI
01-
D
610D
2-
J535
D6
-E
135CI
4-
E
710D
1-
L635
D6
-B
106CI
01-
F
810D
2-
G735
D4
-C
206CI
7-
F
910D
1-
L835
D6
-F
406CI
5-
H
020D
8-
M935
D5
-B
806CI
6-
L
530D
2-
L375
D5
-F
906CI
6-
L
630D
2-
L106
D9
-I1021
CI4
-H
150D
1-
K206
D5
-K
ROT
SIS
NA
RT
101D
1-
B406
D9
-F
310Q
3-
K
301D
2-
E016
D5
-J
610Q
3-I
401D
2-
E116
D5
-G
212Q
5-I
012D
5-I
216D
5-
G104
Q1
-C
112D
5-I
316D
6-
J114
Q1
-D
212D
5-I
416D
8-
K235
Q4
-D
204D
2-
B516
D5
-H
335Q
6-
A
404D
2-I
616D
6-
G535
Q4
-B
504D
2-
B716
D6
-G
106Q
5-
K
604D
2-
B816
D6
-H
206Q
5-
G
704D
3-
B916
D6
-H
306Q
5-
G
804D
2-
B026
D5
-M
406Q
5-
G
214D
3-
C126
D5
-J
606Q
01-
G
414D
3-
B326
D5
-J
706Q
9-
G
024D
1-
B726
D7
-K
806Q
6-
J
124D
2-
C136
D6
-L
906Q
6-
J
324D
2-
B236
D5
-L
424D
2-
M336
D5
-L
A b
oar
d S
emic
on
du
cto
r Vo
ltag
e Ta
ble
A b
oar
d L
oca
tio
n T
able
A b
oar
d I
C V
olt
age
Tab
leA
BC
DE
FG
HI
JK
LM
1 2 3 4 5 6 7 8 9 10
20
us
/div
20
us
/div
20
us
/div
20
us
/div
20
us
/div
20
us
/div
10
us
/div
1.77
Vp-
p (H
)1.
88 V
p-p
(H)
1.88
Vp-
p (H
)
74 V
p-p
(H)
74 V
p-p
(H)
TP
1T
P2
TP
3T
P4
C b
oard
Wav
efor
ms
1.76
Vp-
p (H
)
74 V
p-p
(H)
TP
4
TP
5T
P6
TP
7
A
B
C
D
E
F
G
R
S
T
U
V
W
X
Y
Z
H
I
J
K
L
M
N
O
P
Q
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
35
34
33
31
32
30
29
3435
33
feR
B1TL12-VK
E1TL12-VK
K1TL12-VK
U1TL12-VK
K2TF12-VK
3021C
Fu0001Fu0001
Fu0001Fu0001
mm0. 5
WJ
8221C
--
--
Fu0022
1021N
C,
GUL
PP3
ROT
CE
NN
OC
,G
ULP
P3R
OTC
EN
NO
C,
GUL
PP3
ROT
CE
NN
OC
,G
ULP
P3R
OTC
EN
NO
C,
GUL
PP4
ROT
CE
NN
OC
306LHu3. 3
Hu3. 3Hu3. 3
Hu3. 3m
m0. 5WJ
0021Lm
m0. 5WJ
mm0. 5
WJm
m0. 5WJ
mm0. 5
WJ−
101U
T114
FE-
FT
B104
CE-
FT
B104
PE-
FT
B106
UE-
FT
B104
PE-
FT
B
B
A
3435
36
A
DEFG
B
C
R
ST
VW
X
YZ
1234
5
6
789
10
11
1213
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2829
30
31
32
33
34
35
U
M
N
OPQ
H
I
J
K
L
3637
38
39
241
25
40
4164
65
80
E C B
1 23
1 V OUT
2 V IN3 GND
C
B
E
DTA144ESADTA144ESA-TPDTC114EKADTC114EKA-T146DTC143TKA-T146DTC144EKA-T-146R2SA1037K-T-146-RR2SA1162-G2SA1037K-T-146-QR2SD601A-QTX2SC1623-L5-L62SC2412K-QR2SC2412K-T-146-R
BF421-AMMO2SA1091-O
SE-135NSE135N-LF12
TOP209P
( TOP VIEW )1 4
8 5
BC E
8 7 6 5
1 3 4
( TOP VIEW )
2
LM393DTTDA2822MTEA2124
IRF614-LF
5-4. SEMICONDUCTORS
BCE
LETTER SIDE
2SA933AS-QRT2SAG33ASQT2SA933AS-RT2SC1740S-RT
2SC2785-HFE
E CB
2
1
3
132
DAN202KDAN202K-T146
2SK2251-01-F19
E B C
CATHODE
ANODE
D4SB60L-F
AK04-V1AU-01Z-V1BYD33GBYD33G-AMMODINL20-U-TA2DINL40-U-TR2ERB44-06TP1EGP20GEG-1Z-V1EL1ZERD28-06S
ERD28-06SERC06-15SLFMN-G12SGP08DPKG23RG1CLF-B1RGP10GPKG23RU-3AMRU3YX-LF-C4RU3YX-V1RU-4AM-T31SS292T-77
TDA9392H
40
CATHODE
ANODE
SLA-570KT3F
CATHODE
ANODE
ERA81-004TP1ERA83-006MTZJ-3.6AMTZJ-T-77-2.2AHZS9.INBZMTZJ-T-77-3.6BMTZJ-T-77-5.6BMTZJ-T-77-5.6CMTZJ-T-77-6.8AMTZJ-T-77-6.8CMTZJ-T-77-8.2BMTZJ-T-77-7.5BMTZJ-T-77-9.1AMTZJ-T-77-9.1CMTZJ-T-77-10
MTZJ-T-77-15BMTZJ-T-77-33AMTZJ-33CMTZJ-7.5BRD3.9ES-B2RD5.6ESB2RD6.8ES-B2RD7.5ESB2RD9.1ES-B3RD10ESB2RD15ESB21SS119-25TD1SS133T-77
CATHODE
ANODE
UF4005PKG23
CATHODE
ANODE
1SS355TE-17RD12SB2UDZS-TE-17-4.7BUDZS-TE-17-5.6BUDZS-TE-17-6.8BUDZS-TE-17-9.1BUDZ-TE-17-22B
41
5-5 IC BLOCK DIAGRAMS
2
5
SW
3
1
4
Vref -
-
+
+
GND
1
2
3
7
5
-
+
-
+
6
4 3 2 6 7
1
5
Vsense
RemoteDVLD Internal OFF
Latch
Centre
OscSS
F/B Timer
TSD
OCP
Control
Logic
LevelShift
Sel=34vref 5v15v/8vDriver
Reg. 10v
18 8
14
16
15
10
12
11
9
14
2
6
5
SW
1
VOL PWR
15
3
Pwr Gnd
Sgn Gnd
2K
4 3 7 9 10
MUTE/STBY
PROTECTION
13+Vcc
A BOARD IC604 BA41W12ST
A BOARD IC401/IC531 LM393TD
A BOARD IC601 MCZ3001D
A BOARD IC1201 TDA7494
REF. NO. PART.NO DESCRIPTION REMARK
42
REF. NO. PART.NO DESCRIPTION REMARK
SECTION 6EXPLODED VIEWS
• Items with no part number and no description are not stocked because they are seldom required for routine service.
• The construction parts of an assembled part are indi-cated with a collation number in the remarks column.
• Items marked “ * “ are not stockedsince they are seldom required forroutine service. Some delay shouldbe anticipated when ordering these items.
6-1. KV-21LT1 CHASSIS
NOTE :
1 £ 1-571-433-21 SWITCH, PUSH (AC POWER)2 *4-202-531-01 AC CORD LOCK (SC)3 £ 1-765-286-11 CORD, POWER (KV-21LT1B/21LT1E/21LT1K)
£ 1-776-860-11 POWER CORD, FILTER (KV-21LT1U)4 £ 1-453-345-11 TRANSFORMER ASSY, FLYBACK (NX1748//M3A4)5 8-598-535-00 FRONTEND BTF-EF411(KV-21LT1B)
8-598-531-00 FRONTEND BTF-EC401(KV-21LT1E) 8-598-537-00 FRONTEND BTF-EP401(KV-21LT1K) 8-598-527-00 FRONTEND BTF-EU601(KV-21LT1U)
6 *A-1632-893-A A BOARD, COMPLETE (KV-21LT1B)*A-1632-880-A A BOARD, COMPLETE (KV-21LT1E)*A-1632-892-A A BOARD, COMPLETE (KV-21LT1K)*A-1632-894-A A BOARD, COMPLETE (KV-21LT1U)
7 *4-204-143-02 BRACKET, MAIN8 4-205-362-01 REAR COVER9 7-685-663-71 SCREW +BVTP 4X16 TYPE 2 IT-3
1 2
5
7 8 4
6
UK models only
3
9
43
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
6-2. KV-21LT1 PICTURE TUBE
51 X-4200-621-1 BEZNET ASSY 52-5952 4-047-464-01 CATCHER, PUSH53 4-205-364-01 DOOR54 4-205-365-01 SHAFT DOOR55 4-205-376-01 MULTI BUTTON56 4-205-550-01 COVER MULTI BUTTON57 4-205-363-01 BUTTON, POWER58 4-204-426-01 SPRING59 4-205-375-01 GUIDE, LIGHT60 4-204-666-01 SHEET, BLOTTING61 £ 8-738-836-05 PICTURE TUBE (A51LPT60X) (SD-313)62 £ 8-451-505-11 DEFLECTION YOKE (Y21RSA-S)63 1-452-728-61 COIL, NA ROTATION (RT-154)64 *A-1639-004-A C BOARD, COMPLETE
65 4-369-318-21 SPRING, TENSION66 £ 1-419-187-11 COIL, DEGAUSSING67 *4-204-900-01 BAND, DGC68 *4-202-554-01 HOLDER, HV CABLE69 £ 1-251-839-21 CAP ASSY, HIGH VOLTAGE70 3-704-495-01 SPACER, DY71 4-365-808-01 SCREW (5), TAPPING72 1-529-711-11 SPEAKER, (8CM)73 4-308-870-00 CLIP, LEAD WIRE74 1-452-094-00 MAGNET, ROTATABLE DISK; 15MM Ø75 1-452-032-00 MAGNET, DISK; 10MM Ø76 X-4387-214-1 PERMALLOY ASSY, CORRECTION77 3-701-007-00 BAND, BINDING
72
62
53
76
77
74
54
63
69 71
61
70
73
68
57
51
55
52
58
59
60
75
65
66
67
56
64
REF. NO. PART.NO DESCRIPTION REMARK
44
REF. NO. PART.NO DESCRIPTION REMARK
SECTION 6EXPLODED VIEWS
• Items with no part number and no description are not stocked because they are seldom required for routine service.
• The construction parts of an assembled part are indi-cated with a collation number in the remarks column.
• Items marked “ * “ are not stockedsince they are seldom required forroutine service. Some delay shouldbe anticipated when ordering these items.
6-3. KV-21FT2 CHASSIS
NOTE :
1 2
6
8 9
5
4
7
3
10
1 £ 1-571-433-21 SWITCH, PUSH (AC POWER)2 *4-202-531-01 AC CORD LOCK (SC)3 £ 1-765-286-11 CORD, POWER4 *4-204-517-03 SUPPORT, FBT5 £ 1-453-345-11 TRANSFORMER ASSY, FLYBACK (NX1748//M3A4)
6 8-598-537-00 FRONTEND BTF-EP4017 *A-1632-898-A A BOARD, COMPLETE 8 *4-204-143-11 BRACKET, MAIN9 4-205-399-01 REAR COVER10 7-685-663-71 SCREW +BVTP 4X16 TYPE 2 IT-3
45
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
6-4. KV-21FT2 PICTURE TUBE
51 X-4200-622-1 BEZNET ASSY (KV-21LT1) 52-5652 4-205-398-01 SPRING, DOOR53 4-205-396-11 BUTTON, POWER (BARE)54 4-205-392-11 WINDOW ORNAMENTAL (BARE)55 4-204-426-01 SPRING56 4-205-389-01 GUIDE, LIGHT57 4-204-666-01 SHEET, BLOTTING58 £ 8-738-836-05 PICTURE TUBE (A51LPT60X) (SD-313)59 £ 8-451-505-11 DEFLECTION YOKE (Y21RSA-S)60 1-452-728-61 COIL, NA ROTATION (RT-154)61 *A-1639-004-A C BOARD, COMPLETE62 4-369-318-21 SPRING, TENSION63 £ 1-419-187-11 COIL, DEGAUSSING
64 4-203-390-11 CUSHION, DGC65 4-204-900-01 BAND, DGC66 4-202-554 01 HOLDER, HV CABLE67 £ 1-251-839-21 CAP ASSY, HIGH VOLTAGE68 3-704-495-01 SPACER, DY69 4-365-808-01 SCREW (5), TAPPING70 1-529-710-11 SPEAKER, (5X9CM)71 7-685-648-79 SCREW +BVTP 3X12 TYPE 2 IT-372 4-308-870-00 CLIP, LEAD WIRE73 1-452-094-00 MAGNET, ROTATABLE DISK; 15MM Ø74 1-452-032-00 MAGNET, DISK; 10MM Ø75 X-4387-214-1 PERMALLOY ASSY, CORRECTION76 3-701-007-00 BAND, BINDING
71
59
51
75
76
73
52
60
66
70
58
69
72
67
53
57
74
62
64
65
54 55
56
61 63
64
68
71
70
46
PARTS LISTING TABLE OF CONTENTS
Page
A BOARD COMMON Parts List : Parts common to all models listed in this manual .......................................... 47
A BOARD VARIANT Parts List : Parts that belong only to the model specified
Model
KV-21LT1 ......................................................................................................... 53
KV-21FT2 ......................................................................................................... 53
C BOARD COMPLETE Parts List : ......................................................................................................... 53
MISCELLANEOUS : ......................................................................................................... 55
ACCESSORIES AND PACKAGING MATERIALS : .................................................................................................. 55
Note : Refer to the designated variant parts list when seeking a part indicated by an asterisk (*)
Parts indicated (#) on the Schematic Diagram are not used in this model andtherefore do not appear in the Parts List.
SECTION 7ELECTRICAL PARTS LIST
47
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
4-203-258-01 HOLDER, LED *4-374-846-01 COVER, CAPACITOR, CAP TYPE 4-382-854-01 SCREW (M3X8), P, SW (+) 4-382-854-01 SCREW (M3X8), P, SW (+)
< CAPACITOR >
C001 1-126-933-11 ELECT 100UF 20.00% 16VC002 1-163-233-11 CERAMIC CHIP 18PF 5.00% 50VC004 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC005 1-126-935-11 ELECT 470UF 20.00% 16VC006 1-163-233-11 CERAMIC CHIP 18PF 5.00% 50V
C007 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC008 1-164-337-11 CERAMIC CHIP 2.2UF 16VC009 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC010 1-164-005-11 CERAMIC CHIP 0.47UF 16VC011 1-163-005-11 CERAMIC CHIP 470PF 10.00% 50V
C012 1-126-963-11 ELECT 4.7UF 20.00% 50VC013 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC014 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC015 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC017 1-126-960-11 ELECT 1UF 20.00% 50V
C018 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC020 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25VC021 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC022 1-126-925-11 ELECT 470UF 20.00% 10VC024 1-126-961-11 ELECT 2.2UF 20.00% 50V
C025 1-126-935-11 ELECT 470UF 20.00% 16VC026 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC027 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25VC028 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC030 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50V
C032 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC033 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC035 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC036 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC037 1-137-354-11 FILM 0.01UF 5.00% 100V
C038 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC039 1-164-505-11 CERAMIC CHIP 2.2UF 16VC040 1-163-017-00 CERAMIC CHIP 0.0047UF 10.00% 50VC042 1-162-625-11 CERAMIC CHIP 0.0047UF 5.00% 50VC043 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50V
C044 1-164-346-11 CERAMIC CHIP 1UF 16VC045 1-164-489-11 CERAMIC CHIP 0.22UF 10.00% 16VC046 1-163-037-11 CERAMIC CHIP 0.022UF 10.00% 50VC047 1-126-935-11 ELECT 470UF 20.00% 16VC051 1-163-109-00 CERAMIC CHIP 47PF 5.00% 50V
C053 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25VC055 1-216-295-91 SHORT 0C100 1-126-933-11 ELECT 100UF 20.00% 16VC103 1-126-965-11 ELECT 22UF 20.00% 50VC105 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50V
C106 1-126-933-11 ELECT 100UF 20.00% 16VC110 1-163-113-00 CERAMIC CHIP 68PF 5.00% 50VC111 1-163-113-00 CERAMIC CHIP 68PF 5.00% 50VC253 1-164-336-11 CERAMIC CHIP 0.33UF 25VC403 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50V
C408 1-164-348-11 CERAMIC CHIP 0.12UF 10.00% 25VC409 1-126-964-11 ELECT 10UF 20.00% 50VC410 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC415 1-164-346-11 CERAMIC CHIP 1UF 16VC416 1-126-964-11 ELECT 10UF 20.00% 50V
C421 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC426 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC437 1-164-346-11 CERAMIC CHIP 1UF 16VC438 1-164-346-11 CERAMIC CHIP 1UF 16VC449 1-164-492-11 CERAMIC CHIP 0.15UF 10.00% 16V
C501 1-126-968-11 ELECT 100UF 20.00% 50VC502 1-163-038-91 CERAMIC CHIP 0.1UF 25VC503 1-126-968-11 ELECT 100UF 20.00% 50VC504 1-106-220-00 MYLAR 0.1UF 10.00% 100VC505 1-137-194-81 MYLAR 0.47UF 5.00% 50V
C506 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC508 1-163-035-00 CERAMIC CHIP 0.047UF 50VC509 1-107-364-11 MYLAR 0.01UF 10.00% 400VC510 1-163-005-11 CERAMIC CHIP 470PF 10.00% 50VC513 1-128-560-11 ELECT 22UF 20.00% 100V
C515 1-104-666-11 ELECT 220UF 20.00% 25VC517 1-104-666-11 ELECT 220UF 20.00% 25VC518 1-106-375-12 MYLAR 0.022UF 10.00% 250VC519 1-163-275-11 CERAMIC CHIP 0.001UF 5.00% 50VC520 1-163-038-91 CERAMIC CHIP 0.1UF 25V
C524 1-216-295-91 SHORT 0C525 1-123-024-21 ELECT 33UF 160VC531 1-126-964-11 ELECT 10UF 20.00% 50VC532 1-163-017-00 CERAMIC CHIP 0.0047UF 10.00% 50VC535 1-163-251-11 CERAMIC CHIP 100PF 5.00% 50V
C536 1-117-667-11 FILM 0.47UF 5.00% 250VC537 1-106-351-00 MYLAR 0.0022UF 99% 200V
A Board, Common Parts
A
*A-1632-893-A A Board, Complete (KV-21LT1B)*A-1632-880-A A Board, Complete (KV-21LT1E)*A-1632-892-A A Board, Complete (KV-21LT1K)*A-1632-894-A A Board, Complete (KV-21LT1U)*A-1632-898-A A Board, Complete (KV-21FT2K)
48
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
A
C538 1-165-319-11 CERAMIC CHIP 0.1UF 50VC539 1-107-642-91 ELECT 3.3UF 20.00% 200VC540 1-136-206-11 MYLAR 0.033UF 10.00% 400VC541 1-106-383-00 MYLAR 0.047UF 10.00% 200VC542 1-162-131-11 CERAMIC 220PF 10.00% 2KV
C545 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25VC546 1-135-840-51 FILM 0.036UF 3% 400VC547 1-117-671-21 FILM 1UF 5.00% 250VC550 1-107-638-11 ELECT 33UF 20.00% 160VC552 1-102-212-00 CERAMIC 820PF 10.00% 500V
C555 1-117-644-31 FILM 10000PF 3.00% 1.2KVC580 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50VC582 1-163-255-11 CERAMIC CHIP 150PF 5.00% 50VC583 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50VC600 1-119-888-51 CERAMIC 2200PF 20.00% 250V
C601 £ 1-136-516-12 FILM 0.1UF 20.00% 300VC602 £ 1-136-516-12 FILM 0.1UF 20.00% 300VC603 £ 1-119-888-51 CERAMIC 2200PF 20.00% 250VC604 £ 1-119-888-51 CERAMIC 2200PF 20.00% 250VC605 1-126-935-11 ELECT 470UF 20.00% 16V
C606 1-125-991-11 ELECT 180UF 20% 450VC607 1-126-964-11 ELECT 10UF 20.00% 50VC608 1-126-963-11 ELECT 4.7UF 20.00% 50VC610 1-126-941-11 ELECT 470UF 20.00% 25VC611 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50V
C612 £ 1-104-571-91 CERAMIC 0.0015UF 10.00% 2KVC613 £ 1-104-571-91 CERAMIC 0.0015UF 10.00% 2KVC614 £ 1-161-964-51 CERAMIC 0.0047UF 250VC615 1-115-339-11 CERAMIC CHIP 0.1UF 10.00% 50VC617 1-164-644-11 CERAMIC 330PF 10.00% 500V
C618 1-126-949-11 ELECT 220UF 20.00% 35VC619 1-164-644-11 CERAMIC 330PF 10.00% 500VC620 1-135-871-21 FILM 15000PF 3% 800VC621 1-164-644-11 CERAMIC 330PF 10.00% 500VC622 £ 1-104-571-91 CERAMIC 0.0015UF 10.00% 2KV
C623 £ 1-104-571-91 CERAMIC 0.0015UF 10.00% 2KVC624 1-126-935-11 ELECT 470UF 20.00% 16VC625 £ 1-117-703-11 CERAMIC 0.0047UF 99% 250VC626 1-126-967-11 ELECT 47UF 20.00% 50VC627 1-126-964-11 ELECT 10UF 20.00% 50V
C628 1-126-963-11 ELECT 4.7UF 20.00% 50VC630 1-107-640-41 ELECT 100UF 20.00% 160VC631 1-126-942-61 ELECT 1000UF 20.00% 25VC632 1-126-964-11 ELECT 10UF 20.00% 50VC633 1-163-009-11 CERAMIC CHIP 0.001UF 10.00% 50V
C635 1-136-165-00 MYLAR 0.1UF 5.00% 50VC636 1-136-479-11 FILM 0.001UF 2.00% 50V
C637 1-126-967-11 ELECT 47UF 20.00% 50VC638 1-107-679-91 ELECT 10UF 20.00% 450VC639 1-104-665-11 ELECT 100UF 20.00% 25VC640 1-104-664-11 ELECT 47UF 20.00% 25VC641 1-111-036-11 ELECT 470UF 20.00% 16V
C642 1-104-665-11 ELECT 100UF 20.00% 25VC643 1-164-644-11 CERAMIC 330PF 10.00% 500VC645 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25VC648 1-125-782-91 CERAMIC 4700PF 10.00% 1KVC657 1-126-952-11 ELECT 1000UF 20.00% 35V
C1201 1-126-952-11 ELECT 1000UF 20.00% 35VC1205 1-163-033-91 CERAMIC CHIP 0.022UF 50VC1207 1-115-340-11 CERAMIC CHIP 0.22UF 10.00% 25VC1208 1-535-143-61 LEAD,JUMPER (5.0MM)C1218 1-109-982-11 CERAMIC CHIP 1UF 10.00% 10V
C1219 1-104-666-11 ELECT 220UF 20.00% 25VC1220 1-164-346-11 CERAMIC CHIP 1UF 16VC1221 1-115-339-11 CERAMIC CHIP 0.1UF 10.00% 50VC1223 1-163-125-00 CERAMIC CHIP 220PF 5.00% 50VC1226 1-110-501-11 CERAMIC CHIP 0.33UF 10.00% 16V
C1227 1-163-125-00 CERAMIC CHIP 220PF 5.00% 50V
< CONNECTOR >
CN001 *1-564-508-11 PLUG, CONNECTOR 5PCN501 *1-580-798-11 CONNECTOR PIN (DY)CN504 *1-564-509-11 PLUG, CONNECTOR 6PCN506 1-695-915-11 TAB (CONTACT)CN508 *1-564-508-11 PLUG, CONNECTOR 5P
CN510 *1-564-506-11 PLUG, CONNECTOR 3PCN601 £ *1-580-843-11 PIN, CONNECTOR (POWER)CN602 £ 1-508-765-00 PIN, CONNECTOR (5MM PITCH) 3PCN603 £ *1-508-786-00 PIN, CONNECTOR (5MM PITCH) 2PCN604 £ 1-695-915-11 TAB (CONTACT)
< DIODE >
D001 8-719-069-55 DIODE UDZS-TE17-5.6BD002 8-719-069-55 DIODE UDZS-TE17-5.6BD003 8-719-109-69 DIODE MTZJ-T-77-3.6BD004 8-719-302-45 DIODE SEL1210S-DD005 8-719-110-08 DIODE MTZJ-T-77-8.2B
D006 8-719-109-89 DIODE MTZJ-T-77-5.6BD007 8-719-069-55 DIODE UDZS-TE17-5.6BD008 8-719-074-43 DIODE BAS316-115D010 8-719-074-43 DIODE BAS316-115D011 8-719-074-43 DIODE BAS316-115
D012 8-719-110-08 DIODE MTZJ-T-77-8.2BD013 8-719-109-69 DIODE MTZJ-T-77-3.6B
49
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
D014 8-719-422-12 DIODE UDZ-TE-17-3.9BD016 8-719-109-89 DIODE MTZJ-T-77-5.6BD017 8-719-109-97 DIODE MTZJ-T-77-6.8BD018 8-719-109-69 DIODE MTZJ-T-77-3.6BD019 8-719-109-97 DIODE MTZJ-T-77-6.8B
D020 8-719-109-89 DIODE MTZJ-T-77-5.6BD035 8-719-069-55 DIODE UDZS-TE17-5.6BD036 8-719-069-55 DIODE UDZS-TE17-5.6BD051 8-719-978-33 DIODE UDZS-TE17-6.8BD101 8-719-977-81 DIODE MA8330-TX
D103 8-719-978-33 DIODE UDZS-TE17-6.8BD104 8-719-069-55 DIODE UDZS-TE17-5.6BD210 8-719-069-55 DIODE UDZS-TE17-5.6BD211 8-719-069-60 DIODE UDZS-TE17-9.1BD212 8-719-914-43 DIODE DAN202K-T-146
D402 8-719-978-33 DIODE UDZS-TE17-6.8BD404 8-719-109-89 DIODE MTZJ-T-77-5.6BD405 8-719-978-33 DIODE UDZS-TE17-6.8BD406 8-719-978-33 DIODE UDZS-TE17-6.8BD407 8-719-978-33 DIODE UDZS-TE17-6.8B
D408 8-719-978-33 DIODE UDZS-TE17-6.8BD412 8-719-978-33 DIODE UDZS-TE17-6.8BD414 8-719-978-33 DIODE UDZS-TE17-6.8BD420 8-719-978-33 DIODE UDZS-TE17-6.8BD421 8-719-049-26 DIODE RB721QT-77
D423 8-719-978-33 DIODE UDZS-TE17-6.8BD424 8-719-069-60 DIODE UDZS-TE17-9.1BD435 8-719-069-60 DIODE UDZS-TE17-9.1BD436 8-719-069-60 DIODE UDZS-TE17-9.1BD501 8-719-908-03 DIODE GP08DPKG23
D502 8-719-056-95 DIODE UDZ-TE-17-22BD503 8-719-069-55 DIODE UDZS-TE17-5.6BD504 8-719-074-43 DIODE BAS316-115D505 8-719-988-61 DIODE 1SS355TE-17D506 8-719-908-03 DIODE GP08DPKG23
D507 8-719-070-59 DIODE PDZ6.8B-115D512 8-719-908-03 DIODE GP08DPKG23D513 8-719-908-03 DIODE GP08DPKG23D514 8-719-908-03 DIODE GP08DPKG23D534 8-719-908-03 DIODE GP08DPKG23
D535 8-719-908-03 DIODE GP08DPKG23D536 8-719-945-80 DIODE ERC06-15SLD537 8-719-110-14 DIODE MTZJ-T-77-9.1CD538 8-719-908-03 DIODE GP08DPKG23D539 8-719-928-08 DIODE ERD28-06S
D541 1-535-143-61 LEAD, JUMPER (5.0MM)D573 8-719-976-96 DIODE UDZ-TE-17-4.7B
D601 8-719-510-53 DIODE D4SB60L-FD602 8-719-911-19 DIODE 1SS119-25TDD604 8-719-979-64 DIODE UF4005PKG23D608 8-719-063-70 DIODE D1NL20U-TA2D610 8-719-110-41 DIODE RD15ES-T1B2
D611 8-719-991-33 DIODE 1SS133T-77D612 8-719-991-33 DIODE 1SS133T-77D613 8-719-911-19 DIODE 1SS119-25TDD614 8-719-077-76 DIODE D2SB60A-F04D615 8-719-110-08 DIODE MTZJ-T-77-8.2B
D616 8-719-052-90 DIODE D1NL40-TA2D617 8-719-052-90 DIODE D1NL40-TA2D618 8-719-022-97 DIODE D2S4MTA1D619 8-719-022-97 DIODE D2S4MTA1D620 8-719-109-85 DIODE MTZJ-T-77-5.1B
D621 8-719-109-89 DIODE MTZJ-T-77-5.6BD623 8-719-911-19 DIODE 1SS119-25TDD627 8-719-063-70 DIODE D1NL20-TAD629 8-719-073-23 DIODE ST02D-200TAD631 8-719-921-63 DIODE MTZJ-T-77-7.5B
D632 8-719-063-70 DIODE D1NL20U-TA2D633 8-719-109-69 DIODE MTZJ-T-77-3.6BD634 8-719-074-43 DIODE BAS316-115D639 8-719-080-59 DIODE EK19-V0D640 8-719-921-63 DIODE MTZJ-T-77-7.5B
D1201 8-719-069-55 DIODE UDZS-TE17-5.6BD1203 8-719-914-43 DIODE DAN202K-T-146D1204 8-719-069-55 DIODE UDZS-TE17-5.6B
< FUSE >
F601 £ 1-576-232-21 FUSE (H.B.C.) 5A/250V £ *1-533-725-11 HOLDER, FUSE (F601)
< FERRITE BEAD >
FB601 1-410-397-21 FERRITE 1.1UHFB604 1-410-397-21 FERRITE 1.1UHFB605 1-410-397-21 FERRITE 1.1UHFB606 1-412-911-11 FERRITE 0UHFB607 1-412-911-11 FERRITE 0UH
< IC >
IC001 8-759-671-88 IC TDA9392H/N1/4/0131/T3IC002 8-749-017-44 IC TSOP1540SE1IC003 8-759-672-39 IC PST573IMTIC004 8-759-575-72 IC M24C08-WMN6TIC401 8-759-665-11 IC LM393DT
IC501 8-759-339-59 IC TDA8177
A
50
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
IC531 8-759-665-11 IC LM393DTIC601 8-759-671-30 IC MCZ3001DIC602 8-749-016-19 IC SE135N-LF4IC604 8-759-668-87 IC BA41W12ST-V5IC608 8-759-591-02 IC L78L33ABZ-AP
IC609 8-759-468-89 IC TOP209PIC1201 8-759-665-29 IC TDA7494S
< SOCKET >
J401 1-770-130-11 CONNECTOR (SQUARE TYPE) 21PJ402 1-794-344-11 JACK, PIN 2PJ1200 1-568-267-21 JACK
< COIL >
L001 1-408-611-31 INDUCTOR 47UHL002 1-410-119-11 INDUCTOR 1MHL004 1-408-611-31 INDUCTOR 47UHL006 1-408-611-31 INDUCTOR 47UHL027 1-216-295-91 SHORT 0
L101 1-412-533-21 INDUCTOR 47UHL102 1-408-611-31 INDUCTOR 47UHL405 1-535-143-61 LEAD, JUMPER (5.0MM)L407 1-535-143-61 LEAD, JUMPER (5.0MM)L410 1-216-025-91 RES-CHIP 100 5% 1/10W
L446 1-216-295-91 SHORT 0L501 1-414-187-11 INDUCTOR 47UHL502 1-412-531-31 INDUCTOR 33UHL503 1-412-521-31 INDUCTOR 4.7UHL504 1-535-143-61 LEAD, JUMPER (5.0MM)
L505 1-412-533-21 INDUCTOR 47UHL507 1-412-533-21 INDUCTOR 47UHL532 1-412-553-11 INDUCTOR 3.3MHL533 1-406-989-21 INDUCTOR 10MHL535 1-459-111-00 INDUCTOR 10MH
L537 1-419-552-11 COIL, HORIZONTAL LINEARITYL538 1-419-263-11 COIL, WITH COREL601 1-408-603-31 INDUCTOR 10UHL602 1-408-611-31 INDUCTOR 47UHL1203 1-535-143-61 LEAD, JUMPER (5.0MM)
< PHOTO COUPLER >
PH601 £ 8-749-016-21 IC TCET1103G
< TRANSISTOR >
Q013 8-729-120-28 TRANSISTOR 2SC2412K-T-146-RQ016 8-729-120-28 TRANSISTOR 2SC2412K-T-146-RQ212 8-729-422-33 TRANSISTOR 2PD601AR-115
Q401 8-729-026-49 TRANSISTOR 2SA1037AK-T146-QRQ411 8-729-120-28 TRANSISTOR 2SC2412K-T-146-RQ532 8-729-053-33 TRANSISTOR IRF614-037Q533 8-729-051-82 TRANSISTOR BU4508DX-ON5210Q535 8-729-053-33 TRANSISTOR IRF614-037
Q601 8-729-026-49 TRANSISTOR 2SA1037AK-T146-QRQ602 8-729-119-78 TRANSISTOR 2SC1740S-RTQ603 8-729-029-56 TRANSISTOR DTA144ESA-TPQ604 8-729-030-02 TRANSISTOR DTC144ESA-TPQ606 8-729-052-29 TRANSISTOR 2SK2876-01MR-F122
Q607 8-729-052-29 TRANSISTOR 2SK2876-01MR-F122Q608 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QRQ609 8-729-026-49 TRANSISTOR 2SA1037AK-T146-QR
< RESISTOR >
JR002 1-216-295-91 SHORT 0JR009 1-216-295-91 SHORT 0JR023 1-216-295-91 SHORT 0JR208 1-216-295-91 SHORT 0JR403 1-216-295-91 SHORT 0
JR404 1-216-295-91 SHORT 0JR406 1-216-295-91 SHORT 0JR408 1-216-296-91 SHORT 0JR409 1-216-295-91 SHORT 0JR420 1-216-295-91 SHORT 0
JR508 1-216-295-91 SHORT 0JR516 1-216-296-91 SHORT 0JR517 1-216-296-91 SHORT 0JR601 1-216-296-91 SHORT 0
R003 1-216-065-91 RES-CHIP 4.7K 5% 1/10WR004 1-216-033-00 RES-CHIP 220 5% 1/10WR005 1-216-190-00 RES-CHIP 470 5% 1/8WR006 1-216-025-91 RES-CHIP 100 5% 1/10WR007 1-216-025-91 RES-CHIP 100 5% 1/10W
R008 1-216-025-91 RES-CHIP 100 5% 1/10WR009 1-216-049-91 RES-CHIP 1K 5% 1/10WR010 1-216-059-00 RES-CHIP 2.7K 5% 1/10WR011 1-216-295-91 SHORT 0R012 1-216-113-00 RES-CHIP 470K 5% 1/10W
R014 1-216-065-91 RES-CHIP 4.7K 5% 1/10WR017 1-216-174-00 RES-CHIP 100 5% 1/8WR018 1-216-689-11 METAL CHIP 39K 0.5% 1/10WR020 1-216-077-91 RES-CHIP 15K 5% 1/10WR021 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R022 1-216-089-91 RES-CHIP 47K 5% 1/10WR023 1-216-180-00 RES-CHIP 180 5% 1/8WR024 1-216-025-91 RES-CHIP 100 5% 1/10W
A
51
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
R025 1-216-025-91 RES-CHIP 100 5% 1/10WR026 1-216-025-91 RES-CHIP 100 5% 1/10WR027 1-216-025-91 RES-CHIP 100 5% 1/10WR028 1-216-025-91 RES-CHIP 100 5% 1/10WR029 1-216-061-00 RES-CHIP 3.3K 5% 1/10W
R031 1-216-210-00 RES-CHIP 3.3K 5% 1/8WR032 1-216-061-00 RES-CHIP 3.3K 5% 1/10WR033 1-216-073-00 RES-CHIP 10K 5% 1/10WR034 1-216-121-91 RES-CHIP 1M 5% 1/10WR035 1-216-101-00 RES-CHIP 150K 5% 1/10W
R036 1-216-083-00 RES-CHIP 27K 5% 1/10WR038 1-216-295-91 SHORT 0R039 1-216-214-00 RES-CHIP 4.7K 5% 1/8WR040 1-216-049-91 RES-CHIP 1K 5% 1/10WR041 1-216-025-91 RES-CHIP 100 5% 1/10W
R042 1-216-025-91 RES-CHIP 100 5% 1/10WR044 1-216-073-00 RES-CHIP 10K 5% 1/10WR045 1-216-025-91 RES-CHIP 100 5% 1/10WR046 1-216-025-91 RES-CHIP 100 5% 1/10WR047 1-216-025-91 RES-CHIP 100 5% 1/10W
R048 1-216-073-00 RES-CHIP 10K 5% 1/10WR050 1-216-174-00 RES-CHIP 100 5% 1/8WR051 1-216-295-91 SHORT 0R055 1-216-174-00 RES-CHIP 100 5% 1/8WR056 1-216-081-00 RES-CHIP 22K 5% 1/10W
R057 1-216-083-00 RES-CHIP 27K 5% 1/10WR060 1-216-174-00 RES-CHIP 100 5% 1/8WR061 1-216-174-00 RES-CHIP 100 5% 1/8WR062 1-216-077-91 RES-CHIP 15K 5% 1/10WR063 1-216-061-00 RES-CHIP 3.3K 5% 1/10W
R064 1-216-069-00 RES-CHIP 6.8K 5% 1/10WR065 1-216-295-91 SHORT 0R066 1-216-053-00 RES-CHIP 1.5K 5% 1/10WR067 1-216-073-00 RES-CHIP 10K 5% 1/10WR068 1-216-083-00 RES-CHIP 27K 5% 1/10W
R069 1-216-073-00 RES-CHIP 10K 5% 1/10WR070 1-216-025-91 RES-CHIP 100 5% 1/10WR071 1-216-049-91 RES-CHIP 1K 5% 1/10WR072 1-216-295-91 SHORT 0R074 1-216-073-00 RES-CHIP 10K 5% 1/10W
R075 1-216-295-91 SHORT 0R089 1-216-081-00 RES-CHIP 22K 5% 1/10WR090 1-216-057-00 RES-CHIP 2.2K 5% 1/10WR092 1-216-073-00 RES-CHIP 10K 5% 1/10WR093 1-216-081-00 RES-CHIP 22K 5% 1/10W
R094 1-216-025-91 RES-CHIP 100 5% 1/10WR095 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R096 1-216-025-91 RES-CHIP 100 5% 1/10WR101 1-216-093-91 RES-CHIP 68K 5% 1/10WR102 1-216-097-91 RES-CHIP 100K 5% 1/10WR104 1-216-295-91 SHORT 0R106 1-215-900-11 METAL OXIDE 22K 5% 2W
R107 1-216-025-91 RES-CHIP 100 5% 1/10WR108 1-216-025-91 RES-CHIP 100 5% 1/10WR246 1-260-107-11 CARBON 4.7K 5% 1/2WR248 1-249-429-11 CARBON 10K 5% 1/4WR249 1-216-097-91 RES-CHIP 100K 5% 1/10W
R250 1-216-230-00 RES-CHIP 22K 5% 1/8WR401 1-216-214-00 RES-CHIP 4.7K 5% 1/8WR404 1-216-113-00 RES-CHIP 470K 5% 1/10WR406 1-216-214-00 RES-CHIP 4.7K 5% 1/8WR408 1-216-022-00 RES-CHIP 75 5% 1/10W
R409 1-216-025-91 RES-CHIP 100 5% 1/10WR410 1-216-025-91 RES-CHIP 100 5% 1/10WR411 1-216-022-00 RES-CHIP 75 5% 1/10WR412 1-216-025-91 RES-CHIP 100 5% 1/10WR414 1-216-022-00 RES-CHIP 75 5% 1/10W
R415 1-216-022-00 RES-CHIP 75 5% 1/10WR416 1-216-027-00 RES-CHIP 120 5% 1/10WR419 1-216-022-00 RES-CHIP 75 5% 1/10WR420 1-216-073-00 RES-CHIP 10K 5% 1/10WR421 1-216-049-91 RES-CHIP 1K 5% 1/10W
R423 1-216-113-00 RES-CHIP 470K 5% 1/10WR425 1-216-085-00 RES-CHIP 33K 5% 1/10WR426 1-216-073-00 RES-CHIP 10K 5% 1/10WR428 1-216-073-00 RES-CHIP 10K 5% 1/10WR429 1-216-089-91 RES-CHIP 47K 5% 1/10W
R430 1-216-073-00 RES-CHIP 10K 5% 1/10WR431 1-216-073-00 RES-CHIP 10K 5% 1/10WR433 1-216-073-00 RES-CHIP 10K 5% 1/10WR434 1-216-073-00 RES-CHIP 10K 5% 1/10WR435 1-216-295-91 SHORT 0
R440 1-216-049-91 RES-CHIP 1K 5% 1/10WR441 1-216-051-00 RES-CHIP 1.2K 5% 1/10WR444 1-216-061-00 RES-CHIP 3.3K 5% 1/10WR445 1-216-022-00 RES-CHIP 75 5% 1/10WR446 1-216-113-00 RES-CHIP 470K 5% 1/10W
R447 1-216-295-91 SHORT 0R453 1-216-171-00 RES-CHIP 75 5% 1/8WR454 1-216-001-00 RES-CHIP 10 5% 1/10WR461 1-216-022-00 RES-CHIP 75 5% 1/10WR501 1-216-091-00 RES-CHIP 56K 5% 1/10W
R502 1-216-073-00 RES-CHIP 10K 5% 1/10WR503 1-215-888-00 METAL OXIDE 220 5% 2W
A
52
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
R504 1-249-385-11 CARBON 2.2 5% 1/4WR505 1-216-677-11 METAL CHIP 12K 0.5% 1/10WR506 1-216-665-11 METAL CHIP 3.9K 0.5% 1/10WR507 1-216-349-00 METAL OXIDE 1 5% 1WR508 1-216-677-11 METAL CHIP 12K 0.5% 1/10W
R509 1-216-665-11 METAL CHIP 3.9K 0.5% 1/10WR510 1-216-113-00 RES-CHIP 470K 5% 1/10WR512 1-249-382-11 CARBON 1.2 5% 1/4WR514 1-249-377-11 CARBON 0.47 5% 1/4WR515 1-249-377-11 CARBON 0.47 5% 1/4W
R516 1-214-907-00 METAL 56K 1% 1/2WR517 1-215-463-00 METAL 56K 1% 1/4WR518 1-216-059-00 RES-CHIP 2.7K 5% 1/10WR519 1-216-129-00 RES-CHIP 2.2M 5% 1/10WR520 1-215-883-11 METAL OXIDE 33 5% 2W
R523 1-216-117-00 RES-CHIP 680K 5% 1/10WR524 1-216-083-00 RES-CHIP 27K 5% 1/10WR525 1-216-057-00 RES-CHIP 2.2K 5% 1/10WR526 1-216-089-91 RES-CHIP 47K 5% 1/10WR527 1-216-079-00 RES-CHIP 18K 5% 1/10W
R528 1-216-097-91 RES-CHIP 100K 5% 1/10WR529 1-216-073-00 RES-CHIP 10K 5% 1/10WR530 1-216-085-00 RES-CHIP 33K 5% 1/10WR531 1-216-057-00 RES-CHIP 2.2K 5% 1/10WR532 1-216-085-00 RES-CHIP 33K 5% 1/10W
R533 1-216-081-00 RES-CHIP 22K 5% 1/10WR534 1-216-117-00 RES-CHIP 680K 5% 1/10WR535 1-216-097-91 RES-CHIP 100K 5% 1/10WR539 1-215-892-11 METAL OXIDE 1K 5% 2WR540 1-215-887-00 METAL OXIDE 150 5% 2W
R542 1-216-121-91 RES-CHIP 1M 5% 1/10WR543 1-216-065-91 RES-CHIP 4.7K 5% 1/10WR544 1-216-103-00 RES-CHIP 180K 5% 1/10WR545 1-216-129-00 RES-CHIP 2.2M 5% 1/10WR546 1-215-894-11 METAL OXIDE 2.2K 5% 2W
R547 1-215-886-11 METAL OXIDE 100 5% 2WR548 1-212-849-00 FUSIBLE 4.7 5% 1/4WR549 1-216-369-00 METAL OXIDE 1 5% 2WR551 1-215-873-00 METAL OXIDE 4.7K 5% 1WR552 1-216-097-91 RES-CHIP 100K 5% 1/10W
R553 1-249-381-11 CARBON 1 5% 1/4WR554 1-216-254-00 RES-CHIP 220K 5% 1/8WR557 1-216-065-91 RES-CHIP 4.7K 5% 1/10WR558 1-216-025-91 RES-CHIP 100 5% 1/10WR559 1-249-428-11 CARBON 8.2K 5% 1/4W
R560 1-249-429-11 CARBON 10K 5% 1/4WR561 1-216-129-00 RES-CHIP 2.2M 5% 1/10W
R562 1-216-117-00 RES-CHIP 680K 5% 1/10WR565 1-216-049-91 RES-CHIP 1K 5% 1/10WR583 1-216-081-00 RES-CHIP 22K 5% 1/10WR589 1-216-295-91 SHORT 0R590 1-216-222-00 RES-CHIP 10K 5% 1/8W
R591 1-215-892-11 METAL OXIDE 1K 5% 2WR595 1-249-377-11 CARBON 0.47 5% 1/4WR600 1-216-615-91 METAL CHIP 33 0.5% 1/10WR601 1-216-645-11 METAL CHIP 560 0.5% 1/10WR602 1-202-962-11 CEMENTED 3.3 5% 10W
R603 1-220-926-11 FUSIBLE 0.47 10% 1/2WR605 1-216-049-91 RES-CHIP 1K 5% 1/10WR606 £ 1-202-719-00 SOLID 1M 10% 1/2WR608 1-216-073-00 RES-CHIP 10K 5% 1/10WR609 1-216-675-91 METAL CHIP 10K 0.5% 1/10W
R610 1-215-481-00 METAL 330K 1% 1/4WR611 1-216-059-00 RES-CHIP 2.7K 5% 1/10WR612 1-249-429-11 CARBON 10K 5% 1/4WR613 £ 1-218-265-11 METAL 8.2M 5% 1WR615 1-215-405-00 METAL 220 1% 1/4W
R618 1-247-889-00 CARBON 270K 5% 1/4WR619 1-216-065-91 RES-CHIP 4.7K 5% 1/10WR621 1-216-113-00 RES-CHIP 470K 5% 1/10WR622 1-216-073-00 RES-CHIP 10K 5% 1/10WR623 1-216-081-00 RES-CHIP 22K 5% 1/10W
R624 1-216-001-00 RES-CHIP 10 5% 1/10WR625 1-216-073-00 RES-CHIP 10K 5% 1/10WR627 1-249-389-11 CARBON 4.7 5% 1/4WR628 1-247-791-91 CARBON 22 5% 1/4WR629 1-216-073-00 RES-CHIP 10K 5% 1/10W
R632 1-249-417-11 CARBON 1K 5% 1/4WR633 1-215-481-00 METAL 330K 1% 1/4WR634 1-216-361-21 METAL OXIDE 0.22 5% 2WR635 1-260-300-11 CARBON 4.7 5% 1/2WR636 1-249-413-11 CARBON 470 5% 1/4W
R637 1-216-041-00 RES-CHIP 470 5% 1/10WR639 1-216-683-11 METAL CHIP 22K 0.5% 1/10WR640 1-216-699-91 METAL CHIP 100K 0.5% 1/10WR641 1-216-097-91 RES-CHIP 100K 5% 1/10WR642 1-249-405-11 CARBON 100 5% 1/4W
R643 1-216-089-91 RES-CHIP 47K 5% 1/10WR645 1-216-073-00 RES-CHIP 10K 5% 1/10WR647 1-216-049-91 RES-CHIP 1K 5% 1/10WR648 1-215-481-00 METAL 330K 1% 1/4WR649 1-216-674-11 METAL CHIP 9.1K 0.5% 1/10W
R650 1-216-627-11 METAL CHIP 100 0.5% 1/10WR651 1-220-926-11 FUSIBLE 0.47 10% 1/2W
A
53
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
R652 1-216-081-00 RES-CHIP 22K 5% 1/10WR653 1-216-073-00 RES-CHIP 10K 5% 1/10WR654 1-216-001-00 RES-CHIP 10 5% 1/10WR656 1-216-365-00 METAL OXIDE 0.47 5% 2WR660 1-247-807-31 CARBON 100 5% 1/4W
R1200 1-260-093-11 CARBON 330 5% 1/2WR1201 1-260-093-11 CARBON 330 5% 1/2WR1204 1-216-049-91 RES-CHIP 1K 5% 1/10WR1205 1-216-061-00 RES-CHIP 3.3K 5% 1/10WR1206 1-216-073-00 RES-CHIP 10K 5% 1/10W
R1207 1-216-083-00 RES-CHIP 27K 5% 1/10WR1213 1-216-198-91 RES-CHIP 1K 5% 1/8W
< RELAY >
RY601 £ 1-755-388-11 RELAY (AC POWER)
< SWITCH >
S001 1-571-532-21 SWITCH, TACTILS002 1-571-532-21 SWITCH, TACTILS003 1-571-532-21 SWITCH, TACTILS004 1-571-532-21 SWITCH, TACTILS005 1-571-532-21 SWITCH, TACTIL
S006 1-571-532-21 SWITCH, TACTILS601 £ 1-571-433-21 SWITCH, PUSH (AC POWER)
SW532 1-572-707-11 SWITCH, LEVER
< TRANSFORMER >
T511 £ 1-453-345-11 TRANSFORMER ASSY, FLYBACK (NX1748//M3A4)T531 1-437-210-11 TRANSFORMER, HORIZONTAL DRIVET601 £ 1-435-487-11 TRANSFORMER, LINE FILTERT602 1-431-732-31 TRANSFORMER, CONVERTER (SRT)T603 £ 1-435-525-11 TRANSFORMER, CONVERTER (PIT)
< THERMISTOR >
TH601 1-803-586-11 THERMISTOR, NTC
THP601 £ 1-803-951-11 THERMISTOR, PTC
< VARISTOR >
VDR601 £ 1-803-830-11 VARISTOR (ERZV14D621)
< CRYSTAL >
X001 1-578-774-11 VIBRATOR, CRYSTAL
< CAPACITOR >
C1203 1-126-942-61 ELECT 1000UF 20.00% 25V
< CONNECTOR >
CN1201 1-504-506-11 PLUG, CONNECTOR 3P
< COIL >
L603 1-412-519-11 INDUCTOR 3.3UHL1200 1-535-143-61 LEAD, JUMPER (5.0MM)
< TUNER >
TU101 8-598-535-00 FRONTEND BTF-EF411 (KV-21LT1B) 8-598-531-00 FRONTEND BTF-EC401 (KV-21LT1E) 8-598-537-00 FRONTEND BTF-EP401 (KV-21LT1K) 8-598-527-00 FRONTEND BTF-EU601 (KV-21LT1U)
< CAPACITOR >
C1203 1-535-143-61 LEAD,JUMPER (5.0MM)C1208 1-126-953-11 ELECT 2200UF 20.00% 35V
< CONNECTOR >
CN1201 1-504-507-11 PLUG, CONNECTOR 4P
< COIL >
L603 1-535-143-61 LEAD, JUMPER (5.0MM)
< TUNER >
TU101 8-598-537-00 FRONTEND BTF-EP401
< CAPACITOR >
C701 1-126-934-11 ELECT 220UF 20.00% 16VC702 1-102-110-00 CERAMIC 220PF 10.00% 50VC703 1-102-110-00 CERAMIC 220PF 10.00% 50VC704 1-101-004-00 CERAMIC 0.01UF 50VC705 1-101-004-00 CERAMIC 0.01UF 50V
C708 1-162-114-00 CERAMIC 0.0047UF 2KVC710 1-107-957-11 ELECT 1UF 20.00% 250VC712 1-102-110-00 CERAMIC 220PF 10.00% 50V
A Board Variant Parts KV-21FT2K
*A-1639-004-A C Board, Complete
A
A Board Variant Parts KV-21LT1B/21LT1EKV-21LT1K/21LT1U
C
54
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
C
C713 1-101-004-00 CERAMIC 0.01UF 50VC714 1-104-665-11 ELECT 100UF 20.00% 16VC717 1-102-114-00 CERAMIC 470PF 10.00% 50VC718 1-102-114-00 CERAMIC 470PF 10.00% 50VC719 1-102-114-00 CERAMIC 470PF 10.00% 50V
C1803 1-101-005-00 CERAMIC 0.022UF 50VC1804 1-126-964-11 ELECT 10UF 20.00% 50VC1805 1-137-366-11 MYLAR 0.0022UF 5.00% 50V
< CONNECTOR >
CN702 1-695-915-11 TAB (CONTACT)CN703 *1-564-509-11 PLUG, CONNECTOR 6PCN706 1-695-915-11 TAB (CONTACT)CN707 *1-564-508-11 PLUG, CONNECTOR 5PCN1705 *1-564-506-11 PLUG, CONNECTOR 3P
CN1801 *1-564-506-11 PLUG, CONNECTOR 3P
< DIODE >
D701 8-719-109-93 DIODE MTZJ-T-77-6.2BD702 8-719-991-33 DIODE 1SS133T-77D703 1-535-143-61 LEAD, JUMPER (5.0MM)D704 1-535-143-61 LEAD, JUMPER (5.0MM)D705 1-535-143-61 LEAD, JUMPER (5.0MM)
D706 8-719-991-33 DIODE 1SS133T-77D707 8-719-991-33 DIODE 1SS133T-77D708 8-719-991-33 DIODE 1SS133T-77D709 8-719-991-33 DIODE 1SS133T-77D710 8-719-991-33 DIODE 1SS133T-77
D712 8-719-991-33 DIODE 1SS133T-77D713 8-719-950-57 DIODE BYD33G-AMMOD714 8-719-991-33 DIODE 1SS133T-77D715 8-719-991-33 DIODE 1SS133T-77D716 8-719-991-33 DIODE 1SS133T-77
D717 8-719-991-33 DIODE 1SS133T-77D718 8-719-991-33 DIODE 1SS133T-77D719 8-719-991-33 DIODE 1SS133T-77D720 8-719-110-41 DIODE MTZJ-T-77-15BD721 8-719-991-33 DIODE 1SS133T-77
D722 8-719-991-33 DIODE 1SS133T-77D723 8-719-991-33 DIODE 1SS133T-77D724 8-719-991-33 DIODE 1SS133T-77D725 8-719-991-33 DIODE 1SS133T-77D726 8-719-991-33 DIODE 1SS133T-77
D1801 8-719-110-17 DIODE MTZJ-T-77-10D1802 8-719-110-17 DIODE MTZJ-T-77-10D1803 8-719-110-17 DIODE MTZJ-T-77-10
< IC >
IC1801 8-759-603-37 IC M5216P
< SOCKET >
J701 £ 1-251-595-11 SOCKET, CRT
< COIL >
L704 1-414-183-41 INDUCTOR 10UH
< TRANSISTOR >
Q701 8-729-046-28 TRANSISTOR BF420-126Q702 8-729-119-78 TRANSISTOR 2SC1740S-RTQ703 8-729-046-28 TRANSISTOR BF420-126Q704 8-729-200-17 TRANSISTOR BF421-AMMOQ705 8-729-119-78 TRANSISTOR 2SC1740S-RT
Q706 8-729-046-28 TRANSISTOR BF420-126Q707 8-729-200-17 TRANSISTOR BF421-AMMOQ708 8-729-119-78 TRANSISTOR 2SC1740S-RTQ709 8-729-046-28 TRANSISTOR BF420-126Q710 8-729-200-17 TRANSISTOR BF421-AMMO
Q712 8-729-046-28 TRANSISTOR BF420-126Q713 8-729-046-28 TRANSISTOR BF420-126Q715 8-729-200-17 TRANSISTOR BF421-AMMOQ716 8-729-200-17 TRANSISTOR BF421-AMMOQ717 8-729-200-17 TRANSISTOR BF421-AMMO
Q718 8-729-119-78 TRANSISTOR 2SC1740S-RT
< RESISTOR >
R701 1-247-895-91 CARBON 470K 5% 1/4WR702 1-215-900-11 METAL OXIDE 22K 5% 2WR703 1-249-405-11 CARBON 100 5% 1/4WR704 1-249-401-11 CARBON 47 5% 1/4WR705 1-215-871-11 METAL OXIDE 2.2K 5% 1W
R706 1-249-409-11 CARBON 220 5% 1/4WR707 1-249-414-11 CARBON 560 5% 1/4WR708 1-247-807-31 CARBON 100 5% 1/4WR709 1-249-429-11 CARBON 10K 5% 1/4WR711 1-249-421-11 CARBON 2.2K 5% 1/4W
R712 1-215-871-11 METAL OXIDE 2.2K 5% 1WR714 1-215-900-11 METAL OXIDE 22K 5% 2WR715 1-249-405-11 CARBON 100 5% 1/4WR716 1-249-409-11 CARBON 220 5% 1/4WR717 1-249-414-11 CARBON 560 5% 1/4W
R718 1-202-814-11 SOLID 33K 10% 1/2WR719 1-247-807-31 CARBON 100 5% 1/4W
55
REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK
The components identified byshading and marked are criticalfor safetyReplace only with the part numberspecified.
R720 1-249-421-11 CARBON 2.2K 5% 1/4WR721 1-249-405-11 CARBON 100 5% 1/4WR722 1-249-393-11 CARBON 10 5% 1/4WR723 1-249-393-11 CARBON 10 5% 1/4WR724 1-249-393-11 CARBON 10 5% 1/4W
R726 1-215-871-11 METAL OXIDE 2.2K 5% 1WR727 1-249-409-11 CARBON 220 5% 1/4WR728 1-216-372-11 METAL OXIDE 1.8 5% 2WR729 1-249-414-11 CARBON 560 5% 1/4WR730 1-247-807-31 CARBON 100 5% 1/4W
R731 1-249-421-11 CARBON 2.2K 5% 1/4WR734 1-247-807-31 CARBON 100 5% 1/4WR736 1-215-900-11 METAL OXIDE 22K 5% 2WR741 1-202-549-00 SOLID 100 20% 1/2WR1801 1-249-441-11 CARBON 100K 5% 1/4W
R1805 1-249-429-11 CARBON 10K 5% 1/4WR1806 1-247-899-11 CARBON 680K 5% 1/4WR1807 1-249-429-11 CARBON 10K 5% 1/4WR1808 1-249-429-11 CARBON 10K 5% 1/4WR1809 1-249-429-11 CARBON 10K 5% 1/4W
R1810 1-249-429-11 CARBON 10K 5% 1/4W
< VARIABLE RESISTOR >
RV702 1-241-656-21 RES, ADJ, METAL FILM 110M
1-418-476-21 REMOTE COMMANDER (RM-887)
£ 1-419-187-11 COIL DEGAUSSING 1-452-032-00 MAGNET, DISK; 10MM 1-452-094-00 MAGNET, ROTATABLE DISK; 15MM £ 1-453-345-11 TRANSFORMER ASSY, FLYBACK (NX-1748//M3A4) 1-452-728-61 COIL, NA ROTATION (RT-154)
1-529-711-11 SPEAKER (8CM) (KV-21LT1) 1-529-710-11 SPEAKER (5x9CM) (KV-21FT2) £ 1-571-433-21 SWITCH, PUSH (AC POWER) £ 1-765-286-11 CORD, POWER (KV-21LT1B/21LT1E/21LT1K/21FT2K) £ 1-776-860-11 POWER CORD, FILTER (KV-21LT1U)
£ 8-738-836-05 PICTURE TUBE (A51LPT60X) (SD-313) £ 8-451-505-11 DEFLECTION YOKE (Y21RSA-S) £ 1-251-839-21 CAP ASSY, HIGH VOLTAGE 8-598-535-00 FRONTEND BTF-EF411(KV-21LT1B) 8-598-531-00 FRONTEND BTF-EC401(KV-21LT1E) 8-598-537-00 FRONTEND BTF-EP401(KV-21LT1K/KV-21FT2K) 8-598-527-00 FRONTEND BTF-EU601(KV-21LT1U)
*4-205-481-21 MANUAL, INSTRUCTION (KV-21LT1B) (GERMAN/FRENCH/ITALIAN/DUTCH) *4-205-481-71 MANUAL, INSTRUCTION (KV-21LT1B) (ENGLISH) *4-205-481-11 MANUAL, INSTRUCTION (KV-21LT1E) (GERMAN/GREEK/TURKISH) *4-205-481-51 MANUAL, INSTRUCTION (KV-21LT1E) (SPANISH/PORTUGUESE/FINNISH/SWEDISH/ DANISH/NORWEGIAN) *4-205-481-61 MANUAL, INSTRUCTION (KV-21LT1E) (ITALIAN)
*4-205-481-41 MANUAL, INSTRUCTION (KV-21LT1K) (BELGIAN/CZECH/ENGLISH/DUTCH/ POLISH/RUSSIAN/SLOVAKIAN) *4-205-481-31 MANUAL, INSTRUCTION (KV-21LT1U) (ENGLISH)
*4-205-400-41 MANUAL, INSTRUCTION (KV-21FT2K) (BELGIAN/CZECH/ENGLISH/DUTCH/ POLISH/RUSSIAN/SLOVAKIAN) *4-395-957-01 BAG, PROTECTION
*4-205-642-01 INDIVIDUAL CARTON (KV-21LT1) *4-205-407-01 INDIVIDUAL CARTON (KV-21FT2) *4-205-675-01 CUSHION (UPPER) (ASSY) (KV-21LT1) *4-205-404-01 CUSHION (UPPER) (ASSY) (KV-21FT2) *4-205-674-01 CUSHION (LOWER) (ASSY) (KV-21LT1) *4-205-401-01 CUSHION (LOWER) (ASSY) (KV-21FT2)
REMOTE COMMANDER
ACCESSORIES AND PACKAGING MATERIALS
C
MISCELLANEOUS
9-974-994-01
Sony CorporationSony UK
Service Promotions Dept.
English00EP7174-1
Printed in U.K.© 2000.5
A new TV Repair Assistance Tool that combines ease of use and powerful PC software tools toallow you to save valuable time during many TV repairs.
The TRACE interface connects to the PC's serial port. It providesconnection to the TV's I2C bus and can be provided with an InfraRedtransmitter (optional).
The interface is powered by a standard 9 V PP3 battery for portableuse, and can also be powered by an external 9V/25mA DC powersupply.
The TRACE software that is supplied with the interface allows you to:
With the optional IR Add-on kit, the following features can be added:
Additional features such as Adjustments and Troubleshooting areavailable in chassis-dependent software modules. Please contact yourlocal Sony Service organisation for the latest information.
•••
Read, restore and compare NVM contents via the I2C busAcknowledge check of all I2C devices in the TV setRead Error Codes (emulation of the Error Reader tool)
Remote Commander emulationUser programmable Functional Check through InfraredFast and documented Test Mode setting of all Sony TV chassis
•••
Partnumbers: TRACE Starter Kit (TRACE interface + software): 9-948-320-70TRACE Software (for users of the I2C Link interface): 9-948-340-80TRACE IR Add-on (IR interface + Remote Commander software): 9-948-320-80
PC requirements: IBM-compatible PC with operating system Windows95, Windows98, or WindowsNT*.
* WindowsNT only supported with TRACE interface
Note: For workshops already using the existing I2C Link parallel port interface (9-948-320-30), this software can be used as well, replacing theTV Data Handling software (9-948-340-50), but Error Reader and IR functions can only be accessed with the TRACE interface.
![Sony Kv-29se10b e k Bx-1l-Chassis [ET]](https://static.documents.pub/doc/80x56/55cf9926550346d0339be33d/sony-kv-29se10b-e-k-bx-1l-chassis-et.jpg)
