SERVICE MANUAL
COPYRIGHT © 2017 JVC KENWOOD Corporation No.RA053<Rev.001>2017/6
B5B-7267-00
VHF DIGITAL TRANSCEIVER, UHF DIGITAL TRANSCEIVERRA053<Rev.001>20176SERVICE MANUALB5B-7267-00
NX-3220, NX-3320
COPYRIGHT © 2017 JVC KENWOOD Corporation
TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-72 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-264 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-315 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-149
NX-3220, NX-3320 K,E3 NX-3220, NX-3320 K2,E2 NX-3220, NX-3320 K3,E
This product complies with the RoHS directive for the European market. This product uses Lead Free solder.
1-2 (No.RA053<Rev.001>)
Document CopyrightsCopyright 2017 by JVC KENWOOD Corporation. All rights reserved.No part of this manual may be reproduced, translated, distributed, or transmitted in any form or by any means, electronic,mechanical, photocopying, recording, or otherwise, for any purpose without the prior written permission of JVC KENWOODCorporation.
DisclaimerWhile every precaution has been taken in the preparation of this manual, JVC KENWOOD Corporation assumes no responsibilityfor errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. JVC KENWOOD Corporation reserves the right to make changes to any products herein at any time for improvement purposes.
Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOODCorporation. Any modifying, reverse engineering, copy, reproducing or disclosing on an Internet website of the firmware is strictlyprohibited without prior written consent of JVC KENWOOD Corporation. Furthermore, any reselling, assigning or transferring of thefirmware is also strictly prohibited without embedding the firmware in KENWOOD product memories.
Transceivers containing AMBE+2 Vocoder:The AMBE+2 voice coding technology is embedded in the firmware under the license of Digital Voice Systems, Inc.
CopyrightsThe Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
NOTE• This equipment should be serviced by only qualified technicians.• Danger of explosion if the battery is incorrectly replaced; replace only with the same type.• To dispose of batteries, be sure to comply with the laws and regulations in your country or region.
TM
TM
(No.RA053<Rev.001>)1-3
SPECIFICATION (NX-3220(K,K2,K3) TYPE)
*1 25 and 30 kHz are not included in the models sold in USA or US territories.*2 Full Keypad/Std Keypad Models*3 Full Keypad ModelAnalog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 136-174 MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 260 (64 for no LCD models)
Number of Zones 128 (4 for no LCD models)
Channel Spacing Analog 12.5/15/20/25*1/30*1 kHz
Digital 6.25 / 12.5 kHz
Power Supply 7.5V DC±20%
Battery Life (FDMA/TDMA)5-5-90 duty cycle
With KNB-55L (1,480 mAh) Approx. 8 hours / Approx. 9.5 hours
With KNB-56N (1,400 mAh) Approx. 8 hours / Approx. 9 hours
With KNB-57L (2,000 mAh) Approx. 11 hours / Approx. 13.5 hours
Operating Temperature -22°F to +140°F (-30°C to +60°C)
Frequency Stability ±2.0ppm
Antenna Impedance 50ohm
Dimensions (W x H x D)*2(Projections not included)
Radio only 2.20 x 4.71 x 1.43 in (56 x 119.6 x 36.4 mm)
With KNB-55L 2.20 x 4.71 x 1.43 in (56 x 119.6 x 36.4 mm)
With KNB-56N 2.20 x 4.71 x 1.68 in (56 x 119.6 x 42.7 mm)
With KNB-57L 2.20 x 4.71 x 1.53 in (56 x 119.6 x 39 mm)
Weight (net)*3 Radio only 7.41 oz (220 g)
With KNB-55L 11.1 oz (315 g)
With KNB-56N 14.46 oz (410 g)
With KNB-57L 11.99 oz (340 g)
RECEIVER
Sensitivity NXDN 6.25kHz Digital(3%BER) 0.20μV
NXDN 12.5kHz Digital(3%BER) 0.25μV
DMR 12.5 kHz Digital (5% BER) 0.30μV
DMR 12.5 kHz Digital (1% BER) 0.45μV
Analog (12dB SINAD) 0.25μV
Selectivity [email protected] 65dB
Analog@25kHz 72dB
Intermodulation 70dB
Spurious Rejection 70dB
Audio Distortion 3%
Audio Output (Internal Speaker) 3% Distortion 500mW / 8ohm
5% Distortion 1000mW / 8ohm
TRANSMITTER
RF Power Output 5 W / 4 W / 1 W
Spurious Emission -70dB
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 12.5 kHz 40dB
Audio Distortion 3%
Emission Designator 16K0F3E*1, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W,4K00F1E, 4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD,4K00F2D
1-4 (No.RA053<Rev.001>)
SPECIFICATION (NX-3220(E,E2,E3) TYPE)
*1 Full Keypad/Std Keypad Models*2 Full Keypad ModelAnalog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 136-174 MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 260 (64 for no LCD models)
Number of Zones 128 (4 for no LCD models)
Channel Spacing Analog 12.5/20/25 kHz
Digital 6.25 / 12.5 kHz
Power Supply 7.5V DC±20%
Battery Life (FDMA/TDMA)5-5-90 duty cycle
With KNB-55L (1,480 mAh) Approx. 8 hours / Approx. 9.5 hours
With KNB-56N (1,400 mAh) Approx. 8 hours / Approx. 9 hours
With KNB-57L (2,000 mAh) Approx. 11 hours / Approx. 13.5 hours
Operating Temperature -30°C to +60°C
Frequency Stability ±2.0ppm
Antenna Impedance 50ohm
Dimensions (W x H x D)*1(Projections not included)
Radio only 56 x 119.6 x 36.4 mm
With KNB-55L 56 x 119.6 x 36.4 mm
With KNB-56N 56 x 119.6 x 42.7 mm
With KNB-57L 56 x 119.6 x 39 mm
Weight (net)*2 Radio only 220 g
With KNB-55L 315 g
With KNB-56N 410 g
With KNB-57L 340 g
RECEIVER
Sensitivity NXDN 3 % BER (6.25 kHz/12.5 kHz) 0.20 μV / 0.25 μV
NXDN 1 % BER (6.25 kHz/12.5 kHz) -4.0 dBμV (0.32μV) / -1 dBμV (0.45μV)
DMR 12.5 kHz Digital (5 % BER) -4.5 dBμV (0.30μV)
DMR 12.5 kHz Digital (1 % BER) -1 dBμV (0.45μV)
Analog, EIA 12 dB SINAD (12.5/20&25 kHz) 0.25 μV
Analog, EN 20 dB SINAD (12.5/20&25 kHz) -1 dBμV (0.45 μV) / -3 dBμV (0.35 μV)
Selectivity [email protected] 68dB
Analog@20kHz 74dB
Analog@25kHz 76dB
Intermodulation 65dB
Spurious Rejection 75dB
Audio Distortion 3%
Audio Output (Internal Speaker) 3% Distortion 500mW / 8ohm
5% Distortion 1000mW / 8ohm
TRANSMITTER
RF Power Output 5 W / 4 W / 1 W
Spurious Emission -36 dBm ≤1 GHz, -30 dBm > 1 GHz
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 20 kHz 45dB
Analog @ 12.5 kHz 40dB
Audio Distortion 3%
Emission Designator 16K0F3E, 14K0F2D, 14K0F3E, 12K0F2D, 8K50F3E,7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E,4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD, 4K00F2D
(No.RA053<Rev.001>)1-5
SPECIFICATION (NX-3320(K,K2,K3) TYPE)
*1 25 kHz are not included in the models sold in USA or US territories.*2 Full Keypad/Std Keypad Models*3 Full Keypad ModelAnalog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 400-520 MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 260 (64 for no LCD models)
Number of Zones 128 (4 for no LCD models)
Channel Spacing Analog 12.5/25*1 kHz
Digital 6.25 / 12.5 kHz
Power Supply 7.5V DC±20%
Battery Life (FDMA/TDMA)5-5-90 duty cycle
With KNB-55L (1,480 mAh) Approx. 8 hours / Approx. 9.5 hours
With KNB-56N (1,400 mAh) Approx. 8 hours / Approx. 9 hours
With KNB-57L (2,000 mAh) Approx. 11 hours / Approx. 13.5 hours
Operating Temperature -22°F to +140°F (-30°C to +60°C)
Frequency Stability ±1.0ppm
Antenna Impedance 50ohm
Dimensions (W x H x D)*2(Projections not included)
Radio only 2.20 x 4.71 x 1.43 in (56 x 119.6 x 36.4 mm)
With KNB-55L 2.20 x 4.71 x 1.43 in (56 x 119.6 x 36.4 mm)
With KNB-56N 2.20 x 4.71 x 1.68 in (56 x 119.6 x 42.7 mm)
With KNB-57L 2.20 x 4.71 x 1.53 in (56 x 119.6 x 39 mm)
Weight (net)*3 Radio only 7.41 oz (220 g)
With KNB-55L 11.1 oz (315 g)
With KNB-56N 14.46 oz (410 g)
With KNB-57L 11.99 oz (340 g)
RECEIVER
Sensitivity NXDN 6.25kHz Digital(3%BER) 0.20μV
NXDN 12.5kHz Digital(3%BER) 0.25μV
DMR 12.5 kHz Digital (5% BER) 0.30μV
DMR 12.5 kHz Digital (1% BER) 0.45μV
Analog (12dB SINAD) 0.25μV
Selectivity [email protected] 65dB
Analog@25kHz 72dB
Intermodulation 70dB
Spurious Rejection 70dB
Audio Distortion 3%
Audio Output (Internal Speaker) 3% Distortion 500mW / 8ohm
5% Distortion 1000mW / 8ohm
TRANSMITTER
RF Power Output 5 W / 4 W / 1 W
Spurious Emission -70dB
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 12.5 kHz 40dB
Audio Distortion 3%
Emission Designator 16K0F3E*1, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W,4K00F1E, 4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD,4K00F2D
1-6 (No.RA053<Rev.001>)
SPECIFICATION (NX-3320(E,E2,E3) TYPE)
*1 Full Keypad/Std Keypad Models*2 Full Keypad ModelAnalog measurements made per TIA603. Specifications are measured according to applicable standards.JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.
GENERAL
Frequency Range 400-520MHz
Max. Channels per Radio Up to 1000 channels with option
Number of Channels 260 (64 for no LCD models)
Number of Zones 128 (4 for no LCD models)
Channel Spacing Analog 12.5/20/25kHz
Digital 6.25 / 12.5 kHz
Power Supply 7.5V DC±20%
Battery Life (FDMA/TDMA)5-5-90 duty cycle
With KNB-55L (1,480 mAh) Approx. 8 hours / Approx. 9.5 hours
With KNB-56N (1,400 mAh) Approx. 8 hours / Approx. 9 hours
With KNB-57L (2,000 mAh) Approx. 11 hours / Approx. 13.5 hours
Operating Temperature -30°C to +60°C
Frequency Stability ±1.0ppm
Antenna Impedance 50ohm
Dimensions (W x H x D)*1(Projections not included)
Radio only 56 x 119.6 x 36.4 mm
With KNB-55L 56 x 119.6 x 36.4 mm
With KNB-56N 56 x 119.6 x 42.7 mm
With KNB-57L 56 x 119.6 x 39 mm
Weight (net)*2 Radio only 220 g
With KNB-55L 315 g
With KNB-56N 410 g
With KNB-57L 340 g
RECEIVER
Sensitivity NXDN 3 % BER (6.25 kHz/12.5 kHz) 0.20 μV / 0.25 μV
NXDN 1 % BER (6.25 kHz/12.5 kHz) -4.0 dBμV (0.32μV) / -1 dBμV (0.45μV)
DMR 12.5 kHz Digital (5 % BER) -4.5 dBμV (0.30μV)
DMR 12.5 kHz Digital (1 % BER) -1 dBμV (0.45μV)
Analog, EIA 12 dB SINAD (12.5/20&25 kHz) 0.25 μV
Analog, EN 20 dB SINAD (12.5/20&25 kHz) -1 dBμV (0.45 μV) / -3 dBμV (0.35 μV)
Selectivity [email protected] 68dB
Analog@20kHz 74dB
Analog@25kHz 76dB
Intermodulation 65dB
Spurious Rejection 75dB
Audio Distortion 3%
Audio Output (Internal Speaker) 3% Distortion 500mW / 8ohm
5% Distortion 1000mW / 8ohm
TRANSMITTER
RF Power Output 5 W / 4 W / 1 W
Spurious Emission -36 dBm ≤1 GHz, -30 dBm > 1 GHz
FM Hum & Noise Analog @ 25 kHz 45dB
Analog @ 20 kHz 45dB
Analog @ 12.5 kHz 40dB
Audio Distortion 3%
Emission Designator 16K0F3E, 14K0F2D, 14K0F3E, 12K0F2D, 8K50F3E,7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E,4K00F1D, 4K00F7W, 7K60FXE, 7K60FXD, 4K00F2D
(No.RA053<Rev.001>)1-7
SECTION 1PRECAUTION
This service manual does not describe PRECAUTION.
SECTION 2SPECIFIC SERVICE INSTRUCTIONS
2.1 SYSTEM SET-UP
Merchandise received
Choose the type of transceiver
Transceiver programming
Are you using the optional antenna?
Are you using the speaker microphone?
A personal computer, programming interface (KPG-22U), and FPU (programming software) are required for programming.(The frequency, and signaling data are programmed for the transceiver.)
Frequency range (MHz) RF power LCD 4-key
No
Yes
Yes
No No
No
YesYes
Yes
Type DTMF keypad
TX/RX 136~174
TX/RX 136~174
TX/RX 136~174
5W
5W
5W
NX-3220 K3
NX-3220 K
NX-3220 K2
Yes NoYes
TX/RX 136~174
TX/RX 136~174
TX/RX 136~174
5W
5W
5W
NX-3220 E3
NX-3220 E
NX-3220 E2
YESKRA-22 or KRA-26 (for NX-3220)KRA-23 or KRA-27 (for NX-3320)
Optional antennaNO
NO
(Option)
(Option)
YESKMC-21/KMC-21S/KMC-45/
KMC-45DSpeaker microphone
Delivery
Yes YesYes
No No No
No
Yes
Yes
No No
No
YesYes
Yes
TX/RX 400~520
TX/RX 400~520
TX/RX 400~520
5W
5W
5W
NX-3320 K3
NX-3320 K
NX-3320 K2
Yes NoYes
TX/RX 400~520
TX/RX 400~520
TX/RX 400~520
5W
5W
5W
NX-3320 E3
NX-3320 E
NX-3320 E2
Yes YesYes
No No No
1-8 (No.RA053<Rev.001>)
2.2 REALIGNMENT
2.2.1 Modes
*1:In order to use the Front panel programming mode, it isnecessary to purchase the "Front panel program" featureoption.
2.2.2 How to Enter Each Mode
*2 K2, K3, E and E2 types only.*3 There is the two or three as how to enter.
2.2.3 Panel Test Mode (K2, K3, E and E2 types only)Setting method refer to ADJUSTMENT.
2.2.4 Panel Tuning Mode (K2, K3, E and E2 types only)Setting method refer to ADJUSTMENT.
Mode Function
User mode For normal use.
Panel test mode Used by the dealer to check the fundamental characteristics.
Panel tuning mode Used by the dealer to tune the transceiver.
PC mode Used for communication between the transceiver and PC.
Data programming mode
Used to read and write frequency data and other features to and from the transceiver.
PC test mode Used to check the transceiver using the PC. This feature is included in the FPU.
Firmware programming mode
Used when changing the main program of the flash memory.
Clone mode Used to transfer programming data from one transceiver to another.
Front panel programming mode
Frequency, signaling and features write to the transceiver.
Transceiver information mode
Used to confirm the transceiver firmware version, Encryption Library version.
User mode
Data programming mode
PC tuning mode
Transceiver information mode
PC mode
Panel tuning modePanel test mode
Firmware programming mode
Clone mode
Front panel programming mode*1
PC test mode
Mode Operation
User mode Power ON
Panel test mode*2,*3 • [ ] + Power ON
• [ ] + Power ON *3Select the “Panel Test” using the [] /[] button.Press the [ ] button.
PC mode Received commands from PC
Panel tuning mode *2 [Panel test mode] + [ ]
Firmware programmingmode*3
• [AUX (Orange)] + Power ON
• [ ] + Power ON *2Select the “Firmware Prog” using the[] / [] button.Press the [ ] button.
• If Write is performed by KFL,Firmware programming mode willstart automatically.
Clone mode*2,*3 • [ ] + Power ON
• [ ] + Power ONSelect the “Clone” using the [] / []button.Press the [ ] button.
Front panel programming mode*2,*3
• Press the PF button to which Frontpanel programming mode is setduring the user mode.
• Press the [ ] button and enter theMenu mode.
Select the any icon assigned the Frontpanel programming mode using the[] / [] button.Press [ ] button.Select the “Panel Program” using the[] / [] button.Press the [ ] button.
Transceiver information mode*2,*3
• [Side 1] + Power ON
• [ ] + Power ONSelect the “Transceiver Info” using the[] / [] button.Press the [ ] button.
(No.RA053<Rev.001>)1-9
2.2.5 PC Mode
2.2.5.1 PrefaceThe transceiver is programmed by using a personal computer,programming interface (KPG-22U) and FPU (programmingsoftware).The programming software can be used with a PC. Figure 1shows the setup of a PC for programming.
Fig.1
2.2.5.2 Connection procedure(1) Connects the transceiver to the computer using the
interface cable (KPG-22U).
Note:You must install the KPG-22U driver in the computer touse the USB programming interface cable (KPG-22U).
(2) When the POWER switch on, user mode can be enteredimmediately. When PC sends command the transceiverenter PC mode, and “PROGRAM” is displayed on the LCD.When data transmitting from the transceiver, the red LEDlights.When data receiving to the transceiver, the green LEDlight.
Note:The data stored in the computer must match the “ModelName” when it is written into the flash memory.
2.2.5.3 KPG-22U description (USB programming interfacecable: Option)
The KPG-22U is a cable which connects to a USB port on acomputer.When using the KPG-22U, install the supplied CD (with driversoftware) in the computer. The KPG-22U driver runs underWindows 7, 8.1, 10.The latest version of the USB driver is available for downloadfrom the following URL:http://www.kenwood.com/usb-com/(This URL may change without notice.)
2.2.5.4 Programming software KPG-D3/D3N descriptionThe FPU is the programming software for the transceiversupplied on a CD-ROM. This software runs under Windows 7,8.1, 10.The data can be input to or read from the transceiver and editedon the screen.
Note: KPG-D3N can't be used for E, E2 and E3 types.
2.2.6 Firmware Programming Mode
2.2.6.1 PrefaceFlash memory is mounted on the transceiver. This allows thetransceiver to be upgrade when new features are released in thefuture. (For details on how to obtain the firmware, contactCustomer Service.)
2.2.6.2 Connection procedureConnect the transceiver to the personal computer using theprogramming interface (KPG-22U). (Connection is same as inthe PC mode.)
2.2.6.3 Programming(1) Start up the firmware programming software (KENWOOD
Firmware Loader). The KFL.exe exists in the KPG-D3/D3Ninstalled holder.
(2) Set the baud rate to "auto" or 1152000, 576000, 115200,and 57600.
(3) Set the firmware to be upgrade by file name item.(4) Enter the Firmware programming mode by using section
“2.2.2 How to Enter Each Mode”. Then, the yellow LED onthe transceiver light and "FIRMWARE PROG" is displayed.
(5) Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.
(6) Press “Write” button in the window. When the transceiverstarts to receive data, the “LOADING” display lights.
(7) If writing ends successfully, the checksum is calculatedand a result is displayed.
(8) If you want to continue programming other transceivers,repeat step (4) to (7).
Note:If write is perfomed by KFL, Firmware programmingmode will start automatically even if Firmwareprogramming is set to disable in the programmingsoftware.
2.2.6.4 FunctionIf you press the [ ] button while “FIRMWARE PROG” isdisplayed, the checksum is calculated, and a result is displayed.If you press the [ ] button again while checksum is displayed,“FIRMWARE PROG” is redisplayed.
Note:The text message are displayed for K2, K3, E and E2types only.
PC
KPG-22U
FPU
(E30-3216-05)
Gray
Gray/Black
1.5D-XV Lead wire
1.5D-XV Shield wire
+
–+
–
SP
MIC
Transceiver
USB
KPG-22U
PC
Tuning cable
1-10 (No.RA053<Rev.001>)
2.2.7 Clone Mode (K2, K3, E and E2 types only)Programming data can be transferred from one transceiver toanother by connecting them via their external SP/MICconnectors. The operation is as follows.
The following data cannot be cloned.• Tuning data• Transceiver Embedded Message• ESN (Electronic Serial Number) data
Button guide on the Clone/ Front Panel ProgrammingPassword input screen.
• Confirm ([ ] button): The password confirmation• Delete ([ ] button): Delete the latest digit from the current
password number (Press and hold to delete all passwordnumbers)
• Select([ ] button): Determine the latest digit of thepassword number.
(1) In the source transceiver, enter the clone mode by usingsection “2.2.2 How to Enter Each Mode”. When the Clone/Front Panel Programming Password is set to thetransceiver, "Input Password" is displayed on the LCD.If the password is not set, the transceiver displays "CLONEMODE".
(2) When you enter the correct password, “CLONE MODE” isdisplayed, the transceiver can be used as the cloningsource. The following describes how to enter thepassword.
(3)- How to enter the password using the keypad;
If one of the buttons 0 to 9 is pressed while the “InputPassword” is displayed, the password number isdisplayed on the LCD.Each press of the button shifts the display in order to theleft.When you enter the password and press [ ] or [*]button, “CLONE MODE” displayed if the enteredpassword is correct. If password is incorrect, “InputPassword” is redisplayed.
- How to enter password using the [] and []buttons;If the [] / [] button is pressed while “Input Password”is displayed, the Clone/ Front Panel ProgrammingPassword input screen is displayed.If the [] or [] button is pressed while the clone/ FrontPanel Programming Password input screen is displayed,the number (0 to 9) blinks on the LCD. When you pressthe [ ] button, currently selected number isdetermined. If you press the [ ] button after enteringpassword in this procedure, “CLONE MODE” isdisplayed if entered password is correct. If the passwordis incorrect, “Input Password” is redisplayed.
(4) Power ON the target transceiver.(5) Connecting the cloning cable (part No.E30-3410-05) to the
SP/MIC connectors on the source and target.(6) Press [ ] button on the source while the source displays
“CLONE MODE”. The data of the source is sent to thetarget. While the target is receiving the data, “PROGRAM”is displayed. When cloning of the data is completed, thesource displays “END”, and the target automaticallyoperates in the User mode. The target can then beoperated by the same program as the source.
(7) The other target can be continuously cloned. When the [ ] button on the source is pressed while the sourcedisplays “END”, the source displays “CLONE MODE”.Carry out the operation in step (4) to (6).
Note:• Cannot be cloned if the Password (Write) is programmed to
the target.• “Model name” must be same to clone the transceiver.
Fig.2
2.2.8 Front Panel Programming Mode (K2, K3, E and E2types only)
If the Front Panel Programming Mode is used, the frequency orother data of the conventional channel is rewritable only by thetransceiver.Moreover, the conventional channel can be added.
The following setup items can be changed or added byusing the Front panel programming mode.
• RX/TX Frequency• Channel Type• Transmit Mode (Mixed mode only)• Channel Spacing• Decode QT/DQT/RAN, Encode QT/DQT/RAN• Color Code• Slot Selection• Transmit Power• Channel Name
Button guide on the Clone/ Front Panel ProgrammingPassword input screen.
• Confirm ([ ] button): The password confirmation• Delete ([ ] button): Delete the latest digit from the current
password number (Press and hold to delete all passwordnumbers)
• Select ([ ] button): Determine the latest digit of thepassword number.
2.2.8.1 Enter to the Front panel programming mode.Enter to the Menu Mode by pressing [Front Panel Mode] PFbutton or [Menu] button. When the Front Panel Mode is selected,it can enter to the Front panel programming mode.If the Clone/Front panel programming Password is not set to thetransceiver, "Panel Program" is displayed on the LCD.If the Clone/Front panel programming Password is set to thetransceiver, "Panel Program" is displayed on the LCD when youenter the correct password while “Input Password” is displayed.
Cloning cable(E30-3410-05)
(No.RA053<Rev.001>)1-11
2.2.8.2 Data WritingBefore moving to next Zone/Channel, “Keep This Change?”appears on the LCD, if you select “OK”, the new data is writtento memory. If you select “Cancel”, the new data not be written;the new data will be erased.• The setup items for Front panel programming mode are as
follows.
*4: In "Channel Type" display, "Transmit Mode" can beentered only when Mixed mode is selected.
• Button operation
No. Setup item Display Remarks
1 RX Frequency RX Frequency Receive Frequency
2 TX Frequency TX Frequency Transmit Frequency
3 Channel Type Channel Type Analog/NXDN/DMR
4 Transmit Mode*4 Transmit Mode Analog/NXDN/DMR
5 Channel Spacing
Channel Space Analog:12.5kHz/20kHz/25kHzNote: 20kHz is applied for E, E2 and E3 types only.
NXDN: 6.25kHz/12.5kHz
DMR: 12.5kHz
6 RX Signaling RX QT/DQT Receive QT/DQT
7 TX Signaling TX QT/DQT Transmit QT/DQT
8 RX RAN RX RAN None, 1~63
9 TX RAN TX RAN None, 1~63
10 Color Code Color Code 0 ~15
11 Slot Selection Slot Selection Slot 1, Slot 2
12 Transmit Power Transmit Power Low/Medium/High
13 Channel Name Channel Name
No. Setup item Display Remarks
Button\Item
Zone Select
Channel Select
RX Frequency
TX Frequency
Channel Type Transmit Mode *7 Channel Spacing
[ ] Decision Decision Decision Decision Decision Decision Decision
[ ] Unused Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to thepreviousitem
Back to the previous item
[ ] Unused Unused Go to the TX Frequency
Go to the RX Frequency
Unused Unused Unused
[ ] Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel programmode
Exit panel program mode
[] Zone change Channel change
Fresuency up Fresuency up Channel type change
Transmit Mode Change
Channel Spacing Change
[] Zone change Channel change
Frequency down
Frequency down
Channel type change
Transmit Mode Change
Channel Spacing Change
[] Unused Unused Frequency step change
Frequency step change
Unused Unused Unused
[] Unused Unused Frequency step change
Frequency step change
Unused Unused Unused
Keypad[0] ~ [9]*5
Zone number select
Channel number select
Go to the direct enter mode Channel number select (1,2 or 3)
Transmit Mode number select (1 or 2)
Channel spacing select *6
Keypad[*] *5
Decision Decision Decision Decision Decision Decision Decision
Keypad[#] *5
Unused Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to theprevious item
Back to the previous item
1-12 (No.RA053<Rev.001>)
*5: K3, K6, E types only*6: K type Channel spacing select (1 or 2) E type Channel spacing select (1, 2 or 3)*7: Mixed Mode only
• Direct enter mode
*8 K3, K6, E types only
Button\Item
RX Signaling TX Signaling RX RAN TX RAN Color Code Slot Selection
Transmit Power
Channel Name
[ ] Decision Decision Decision Decision Decision Decision Decision Decision
[ ] Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to thepreviousitem
Back to the previous item
Back to the previous item
Back to the previous item/Delete
[ ] Unused Unused Unused Unused Unused Unused Unused Character/Digit switching
[ ] Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel program mode
Exit panel programmode
Exit panel program mode
Exit panel program mode
Exit panel program mode
[] Signaling number change
Signaling number change
RX RAN up TX RAN up Color Code up
Slot up Transmit power change
Go to the direct enter mode
[] Signaling number change
Signaling number change
RX RAN down
TX RAN down
Color Code down
Slot down Transmit power change
[] Signaling type change
Signaling type change
RX RAN ON/OFF
TX RAN ON/OFF
Unused Unused Unused
[] Signaling type change
Signaling type change
RX RAN ON/OFF
TX RAN ON/OFF
Unused Unused Unused
Keypad[0] ~ [9] *5
Go to the direct enter mode Slotnumberselect (1 or 2)
Transmit power select (1, 2 or 3)
Keypad[*] *5
Decision Decision Decision Decision Decision Decision Decision Decision/ Character/ Digit switching
Keypad[#] *5
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to the previous item
Back to theprevious item
Back to the previous item
Back to the previous item
Button\Item
RX Frequency
TX Frequency
RX Signaling
TX Signaling
RX RAN
TX RAN
Color Code
Channel Name
[ ] Decision Character/Channel name decision
[ ] Delete
[ ] Unused Input character switching
[ ] Exit panel program mode
[] Unused Character selection (upper case character → lower-case character → digit → upper case character...)
[] Character selection (upper case character → lower-case character → digit → upper case character...)
[] Move a cursor to the right
[] Move a cursor to the left
Keypad[0] ~ [9] *8
Add a digit to the current number
Keypad[*] *8
Decision Input character switching
Keypad[#] *8
Delete/Back to the previous item Delete
(No.RA053<Rev.001>)1-13
• Front panel programming mode flow chart
Input Password
Front panel Programming mode
tceleS enoZ?egnahC sihT peeK
tceleS lennahCemaN lennahC
Transmit Power Low Medium High Blank Channel Select the setting channel.
"System Type = Conventional"
there is more than two.
System Select Analog DMR or NXDN
RX Frfequency
FFOycneuqerF XT
golanAepyT lennahC
12.5kHz 25.0kHz 20.0kHz
When the KPG-D3N is used, 25.0kHz may not be allowed depends on the frequency (K, K2, K3 types only).
Channel Spacing 12.5kHz
RX Signaling OFF QT DQT N DQT I
TX Signaling OFF QT DQT N DQT I
Color Code
Slot Selection
DMR
NXDN
[Channel Type]:"DMR","Mixed"(Transmit Mode:DMR) and when two kinds of Channel Type is set.
[Channel Type]: "Analog"
[TX Frequency]: "OFF"
[Channel Type]: "Analog"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN), "Mixed"(Transmit Mode: DMR) and when a kind of Channel Type is set.
[TX Frequency]: Other than "OFF"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: DMR)
Clone/Front Panel Password
[TX Frequency]: Other than "OFF"[Channel Type]: "DMR","Mixed"(Transmit Mode: DMR)
RX RAN
TX RAN
[TX Frequency]: "OFF"[Channel Type]: "DMR"
[System Type]: "DMR"
[System Type]: "NXDN"
6.25Hz
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[ ]
[ ]
[ ] or [ ]
[No]
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: DMR)
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[TX Frequency]: Other than "OFF"
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[Channel Type]: "NXDN", "Mixed"(Transmit Mode:NXDN) and when two kinds of Channel Type is set.
[ ]
[ ][TX Frequency]: "OFF"
[Channel Type]: "NXDN"
[ ]
[Channel Type]: "NXDN", "Mixed"(Transmit Mode: NXDN)
[ ]
[ ] or [ ] [ ] or [ ]
[ ] or [ ]
Mixed
[System Type]: "DMR" or ”NXDN” and [Channel Type]: "Mixed"[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ] [ ] or [ ] [ ] or [ ]
[ ] or [ ] [ ] or [ ] [ ] or [ ]
Enter the Front panel programming mode by using section "2.2.2 How to Enter Each Mode".
[ ]
[ ] or [ ]
Transmit Mode select golanA
DMR
NXDN
[System Type]: "DMR"
[System Type]: "NXDN"
[ ] or [ ]
[ ] or [ ]
[ ] or [ ][ ] or [ ]
[Channel Type]: "Mixed" and when Channel Spacing in two kinds of Channel Type is set.
1-14 (No.RA053<Rev.001>)
2.2.9 Transceiver Information Mode (K2, K3, E and E2 types only)Use this function to confirm the transceiver firmware version, Encryption Library Version.
(1) Enter the Transceiver Information mode by using section "2.2.2 How to Enter Each Mode".(2) The transceiver fi rmware version appears on the LCD.(3) Use the [] and [] buttons to select the confirmation items.
(4) To exit the transceiver information mode, turn the transceiver power OFF.
Note:The Encryption Library Version will also display Radio Feature License (KWD-3004AE) as Inactive.
2.3 CIRCUIT DESCRIPTION
2.3.1 OverviewThe NX-3220 is a VHF Analog FM & Digital Portable transceiver designed to operate in the frequency range of 136 to 174MHz.The NX-3320 is a UHF Analog FM & Digital Portable transceiver designed to operate in the frequency range of 400 to 520MHz.The unit consists of a transceiver IC, a transmitter, a digital control unit, and a power supply circuit.
2.3.2 Frequency ConfigurationThe receiver uses the direct conversion system. Incoming signals from the antenna are mixed with the local signal from the PLL circuitand converted to the baseband signal. The transmit signal frequency is generated by the VCO/PLL, and modulated by the signal fromthe DSP. It is then amplified and fed to the antenna.
Fig.1 Frequency configuration
Transceiver firmware version
Encryption Library Version
[ ]/[ ]
[ ]/[ ]
ANT SW
FINAL AMP
DRIVE AMP
TRANSCEIVER IC
VCO
TCXO 19.2MHz
BASEBAND CIRCUIT
CODEC
AF AMP
MIC
SP
(No.RA053<Rev.001>)1-15
2.3.3 Receiver System
2.3.3.1 RF circuitThe receive signal from ANT SW (D201, D202, D203 and D205 (D205 is the NX3220 only.)) passes through the high-pass filter (L302,L307, L308, L312, L313, L314 and L315) to remove unwanted signals and amplified by a RF amplifier (incorporated in IC303). Thesignal is then fed to the mixer (incorporated in IC303) and converted to the baseband signal.
2.3.3.2 Baseband circuitThe baseband signal is then be fed into an ADC (incorporated in IC303), generates the I and Q data. This data is in the form of SerialInterface, and sent to the MPU/DSP (IC401).
Fig.2 RF and Baseband circuit
2.3.3.3 Audio amplifier circuitAudio processing (high-pass filter, low-pass filter, de-emphasized and so on) at Analog FM mode and decoding at Digital mode areprocessed by DSP. I2S signal from DSP is converted to audio signal at IC601. The signal goes to internal speaker through the internalClass-D amplifier or Jack connector for external speaker through the single-end audio power amplifier (IC650).Audio path inside the Codec IC is controlled by I2C.
Fig.3 Audio amplifier circuit
ANT
ANT LPF SW
D201 D202 D203 D205
ANT
L302 L307 L308
HPF
IC303
L312, L313 L314, L315
HPF
RFAMP MIXER
PLL
VCO
ADC
Serial I/F
IC401
MPU/DSP
LC
SE
IC65
I/F
IC303
Transceiver IC
Serial
IC401
MPU/DSP
DSP
IC601
CODEC
DA
I2C
I2SClass D
FIlter
External Speaker
Internal Speaker
1-16 (No.RA053<Rev.001>)
2.3.4 Transmitter System
2.3.4.1 Audio Band CircuitThe signal from microphone is amplified and converted to digital signal by IC601, IC601 includes AGC function. Digital signal istransferred to IC401.
2.3.4.2 Baseband CircuitThe audio signal transferred from IC601 is processed at IC401.Voice signals of 300Hz or lower and frequencies of 3kHz or higher are cut off and an audio range 300Hz to 3kHz is extracted. Theaudio signal is then pre-emphasized in FM mode and synthesized with the signals, such as QT and DQT, as required, and istransferred to PLL Frequency Synthesizer block in IC303. The DTMF and MSK baseband signals are also generated by IC401.In Digital mode, the audio signal is converted to the 4-Level FSK baseband signal and is transferred to PLL Frequency Synthesizerblock in IC303.
Fig.4 Audio and Baseband circuit
2.3.4.3 Drive and Final amplifierThe signal from the IC303 is amplified by pre-drive amplifier (IC202). The output of the pre-drive amplifier is amplified by the driveamplifier (Q201) and final amplifier (Q202) to 5W (1W when the power is low). IC202 is MMIC. Q201 and Q202 are MOS FET. Theoutput of the final amplifier is then passed through the harmonic filter (LPF) and antenna switch (D201, D202 and D203) and appliedto the antenna terminal.
2.3.4.4 APC circuitThe APC circuit always monitors the current flowing through the drive amplifier (Q201) and final amplifier (Q202). And APC keepscurrent constant.The voltage drop at R248 and R250 is caused by the current flowing through the RF power amplifier and this voltage is applied to APCcircuit. Output voltage from APC controls the VGG of Q201 and Q202 to keep the current constant. The change of power high/low iscarried out by the change of the reference voltage.
Fig.5 Drive and Final amplifier and APC circuit
2.3.5 PLL Frequency Synthesizer
2.3.5.1 TCXO (X401)TCXO (X401) generates a reference frequency of 19.2MHz for the PLL frequency synthesizer. This reference signal is buffered byQ401. And it is distributed to PLL (IC303), IC401 and IC351.The oscillation frequency is adjusted TCXO directly by controlled the D/A converter of FCNT.
AD I/F
Transceiver IC
IC303
Serial
DSP
MPU/DSP
IC401 IC601
CODEC
I2C
I2S
External MIC
Internal MIC
+B
IC303
APC reference voltage
IC203 APC
R250 R248
ANT SW Final
Q202 Q201
Drive Pre-Drive
IC202
(No.RA053<Rev.001>)1-17
2.3.5.2 VCO• NX-3220
There is one VCO contain TX VCO and RX VCO.The VCO (Q131) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 272 to 348MHz. Thetransmit frequency range is same as receiver frequency range. The local signal frequency range is also 272 to 348MHz.The oscillation frequency is divided into two by IC 303 and it becomes the use frequency.The VCO oscillation frequency is determined by voltage control terminals "CP" and "ASSIST".The voltage control terminal "CP" is controlled by PLL (IC303). The voltage control terminal "ASSIST" is controlled by the controlvoltage from D/A converter (IC410).For the modulation input terminal, "VCO_MOD" of PLL (IC303), the output frequency changes according to the applied voltage. Thisis used to modulate the VCO output.
• NX-3320There are two VCO contain VCO_L and VCO_H.The VCO_H (Q131) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 920 to 1040MHz.The transmit frequency range is same as receiver frequency range.The local signal frequency range is also 920 to 1040MHz.The VCO_L (Q151) generates the carrier for the transmitter and the receiver. VCO oscillation frequency range is 800 to 920MHz.The transmit frequency range is same as receiver frequency range.The local signal frequency range is also 800 to 920MHz.The oscillation frequency is divided into two by IC 303 and it becomes the use frequency.The VCO oscillation frequency is determined by voltage control terminals "CP" and "ASSIST".The voltage control terminal "CP" is controlled by PLL (IC303). The voltage control terminal "ASSIST" is controlled by the controlvoltage from D/A converter (IC410).For the modulation input terminal, "VCO_MOD" of PLL (IC303), the output frequency changes according to the applied voltage. Thisis used to modulate the VCO output.
2.3.5.3 PLLPLL (IC303) compares the difference in phases of the VCO oscillation signal and the TCXO (X401) reference frequency. And it returnsthe difference voltage to the VCO CP terminal and realizes the "Phase Locked Loop". This allows the VCO oscillation frequency toaccurately match (lock) the desired frequency.When the frequency is controlled by the PLL, the frequency convergence time increases as the frequency difference increases whenthe set frequency is changed. To supplement this, The ASSIST Voltage from D/A converter (IC410) is used before control by the PLL(IC303) to bring the VCO oscillation frequency close to the desired frequency. As a result, the VCO CP voltage does not change andis always stable at approx. 2.5V. The desired frequency is set for the PLL (IC303) by the MPU/DSP (IC401) through the 3-line "/DCR_CS", "DCR_DO", "BCLK" serialbus for PLL. IC401 monitors through the "PLD", whether the PLL (IC303) is locked or not. If the VCO does not lock to desired frequency(unlock), the "PLD" logic is low.
2.3.6 Control CircuitThe control circuit consists of MPU/DSP (IC401) and its peripheral circuits. IC401 mainly performs the following;
(1) Switching between transmission and reception by PTT signal input.(2) Reading system, zone, frequency, and program data from the memory circuit.(3) Sending frequency program data to the PLL.(4) Controlling the audio mute circuit by decode data input.
2.3.6.1 MPUThe MPU/DSP (IC401) is 32bit RISC processor and Fixed/Floating-Point VLIW DSP, equipped with peripheral function.This MPU operates at 288MHz (MAX) clock and 3.2V /1.8V/1.2V DC. Controls the flash memory, Mobile DDR, the receive circuit, thetransmitter circuit, the control circuit, and the display circuit and transfers data to or from an external device.
2.3.6.2 Memory CircuitMemory circuit consists of the MPU/DSP (IC401) and the Mobile DDR (IC402), the flash memory (IC404). The flash memory hascapacity of 512Mbit that contains the transceiver control program for the MPU and stores the data. It also stores the data for transceiverchannels and operating parameter that are written by the FPU. This program can be easily written from external devices. The MobileDDR has capacity of 512Mbit. The MPU copies the program to the Mobile DDR from Flash memory. And MPU is used as a work areaMobile DDR.
Flash memory
Note:The flash memory stores the data that is written by the FPU (KPG-D3/D3N), tuning data (Deviation, Squelch, etc.), and firmwareprogram (User mode, Test mode, Tuning mode, etc.). This data must be rewritten when replacing the flash memory.
Mobile DDR (static memory)
Note:Mobile DDR is used as a work area of the MPU.
1-18 (No.RA053<Rev.001>)
2.3.6.3 LCDThe LCD is controlled using parallel interface from MPU /DSP (IC401).
2.3.6.4 Button Detection CircuitButtons are detected using MPU/DSP (IC401).
2.3.6.5 Low Battery WarningThe battery voltage is divided using R65 and R66, it is detected by A/D converter (IC409).When the battery voltage falls below the voltage set by the Low battery warning adjustment, the red LED blinks to notify the operatorthat it is time to replace the battery. If the battery voltage falls even more (approx. 5.8V), a beep sounds and transmission stops.
2.3.6.6 DSPThe DSP circuit consists of a MPU/DSP (IC401) and processes the baseband signal. The DSP operates at 288MHz (MAX) clock, theI/O section operates at 3.2V/1.8V and the core section operates at 1.2V.The DSP carries out the following processes:• 4Level FSK processing• Analog FM pre-emphasis/de-emphasis• Vocoder processing between audio codec and modulation/demodulation• CAI processing, such as error correction encoding• QT/DQT encoding/decoding• DTMF encoding/decoding• MSK encoding/decoding• 2-tone /5-tone encoding/decoding• Compressor/expander processing• Voice scrambler processing• Transmit/receive audio filtering processing• Microphone amplifier AGC processing• Audio mute processing• Modulation level processing• Active Noise Reduction• Voice recording/playback processing• Voice announce processing
2.3.7 Power Supply CircuitThe battery voltage (+B) is provided from battery terminal. The battery voltage passes through the 3.15A fuse (F1), and goes to RFfinal amplifier, AVR ICs (IC9, IC17, IC651, IC6, IC15), DC/DC converter (IC3), transistor (Q7 through the 0.5A fuse (F2)), transistor(Q650 through the 0.315A fuse (F650)), and voltage detector IC (IC1). Voltage detector (IC1) watches battery voltage. If the batteryvoltage is enough higher than 5.6V, detector outputs High. Then, IC9 (31BU) outputs 3.1V, and IC10 (12BU) outputs 1.2V.When the VOL SW is turned on, SB1 becomes high (battery voltage). DC/DC (IC3) operates if both SB1 and output of detector arehigh. IC3 (38M) outputs 3.8V, and IC2 (12M) outputs 1.2V. Then, IC4 (18M) outputs 1.8V. Then, IC5 (32M) outputs 3.2V. Then, IC8(18BT) outputs 1.8V. Then, IC7 (32BT) outputs 3.2V. Then, IC11 (32A) outputs 3.2V, and IC17 (50A) outputs 5.0V. Then, IC12(18M_3) outputs 1.8V, and Q7 (53AF) is turned on. Voltage detector (IC403) watches IC3 (38M) output voltage. If the 38M outputvoltage is enough higher than 3.5V, detector outputs High.As a result, MPU/DSP (IC401) operated. SBC signal becomes High after MPU/DSP (IC401) operates, and IC13 (200C), and IC14 (32C), and IC6 (50C), and Q4 (SB2) areturned on.When 5VC signal becomes High, IC651 (50J) operates. When TXC signal becomes High, IC15 (50T) operates. IC15 (50T) is turnedon in transmit mode. Switches are controlled by MPU/DSP (IC401). When the VOL SW is turned off /PSW signal becomes Low. After detecting /PSW signal, MPU/DSP (IC401) changes SBC signal toLow.38M is fed to IC13 (200C). IC13 (200C) is the DC/DC boost converter. IC13, D10, C50 consist of a voltage quadrupler.The 200C circuit then outputs approximately +20VDC.
Low battery warning Battery condition
The red LED blinks duringtransmission.
The battery voltage is low but thetransceiver is still usable.
The red LED blinks and thewarning tone beeps whilethe PTT switch is pressed.
The battery voltage is low and thetransceiver is not usable to makecalls.
(No.RA053<Rev.001>)1-19
38M
AudioCodec DCVDD
+B
12M
18M
32A
F1(3.15A)
Battery
VOL SW
3.5V DET
32M
32CDirect Conversion Transceiver
5.6V DET
/RST
/PSW
Q3Lvl Conv
Q2Lvl Conv
Q1D8OR
200C
IC401MPU/DSP
SB1
SBCAND
IC1
IC403
/BINT
SBCIC14
IC13
IC5
IC11
32BTIC7
18BTIC8
IC3
31BUIC9
BackUpBattery
IC2
IC4
Final Amp, APC
MPU/DSP RTCIC1012BU
IC1218M_3
MPU/DSP Core,MPU/DSP PLL,
MPU/DSP 1.8V I/O, mDDR2,LCD Module I/O
Flash ROMI/O
BT & GPS I/O
BT & GPS VDD
AudioCodec VDD, 8bit/8ch DAC, 12bit/4ch DAC
MPU/DSP 3.2V I/O,Flash ROMVCC,AudioCodec DBVDDLCD Module
ASSIST
1-20 (No.RA053<Rev.001>)
Fig.6 Power supply circuit
2.3.8 Signaling Circuit
2.3.8.1 Encode (QT/DQT/DTMF/2-tone/MSK)Each signaling data signal of QT, DQT, DTMF, 2-tone and MSK is generated by IC401, superposed on a modulation signal and outputto VCO and PLL.
2.3.8.2 Decode (QT/DQT/DTMF/2-tone/MSK) The audio signal and signaling data (QT, DQT, DTMF, 2-tone and MSK) are separated by IC401. Next IC401 decode the signalingdata.
2.3.9 Bluetooth/GPS CircuitThe main component of the Bluetooth/GPS circuit is Bluetooth /GPS IC (IC351).The clocks of Bluetooth/GPS IC require 19.2MHz for core and 32.768kHz slow clock (X351) for UART. 19.2MHz clock (X401) is sharedwith MPU/DSP (IC401), and is supplied through the Clock buffer amplifier (Q401).Bluetooth/GPS IC communicates to the MPU/DSP (IC401) on the HCI UART. Interface of UART & Digital audio (PCM) between theMPU/DSP (IC401) and the Bluetooth/GPS IC (IC351), have level conversion at the level conversion IC (IC352, IC353).The Bluetooth/GPS IC is powered by 1.8V and 3.2V which are supplied from 2 discrete external regulators (IC8 and IC7). The inputof these regulators is sourced from a switching regulator (IC3) which regulates the battery voltage to 3.8V.
Fig.7 Bluetooth/GPS circuit
Q7
F2(0.5A)
50A
50J
50C
SW
50T
Q4SB2
8bit ADC
Q650
F650(0.315A)
Audio Amp(2Pin Jack Option)
Int AF Amp
TX circuit
ANTSW
VCO
2Pin Jack Option
KEY Back Light, 3Color LED,8bit/16ch ADC
IC17
IC651
IC6
IC201
IC15
53AF
AF SW
5VC
SBC
ANTSW
TXC
SBC
1.8V
3.2V
OSCILLATOR
32.768kHz
GPS_TX
GPS_RXMPU/DSP
HPF Pre-SAW LNAMatching
GPS antenna
Post-SAWPost-SAW
LNA Supply
LNA ModuleTCXO
19.2MHz
ClockBuffer
Level
Conversion
GPS IC(IC850)
GPS_LNA_IN(L2)
GPS_EXT_LNA_EN(H6)
VDD_TCXO(G1)
TCXO_CLK_LV(F1)
BT_HCI_UART_TX(A4) BT_HCI_UART_RX(B5)
RTC_CLK(H9)
BTFM_nSHUTDOWN(A6)GPS PA EN(G3)
VBAT1(A2)TCXO_LDO_IN(H1)
VDDS
LC filter
BT antenna
BT_RF
(No.RA053<Rev.001>)1-21
2.3.9.1 Bluetooth CircuitTX/RX frequency is 2400-2483.5MHz (79ch Hopping, 2402-2480MHz, 1MHz step). Transmitting power is +0dBm at Bluetoothantenna input.Bluetooth antenna is made of sheet metal, and connected to the Bluetooth / GPS IC (IC351) through the LC filter (L361).
Fig.8 Bluetooth circuit
Frequency configuration for Bluetooth is following:There are two LO modes: 2X and Offset LO (OSLO). 2X where LO is 2*RF_FREQ (e.g. when transmitting at 2441MHz it is at4882MHz). OSLO where LO is at (2/3)*RF_FREQ (e.g. when transmitting at 2441MHz it is at 1627.333MHz). In RX the 2X is always used.In GFSK TX if power is >10dBm then OSLO is usedIn EDR2 TX if power is >-12dBm then OSLO is usedIn EDR3 TX if power is >-12dBm then OSLO is usedOtherwise 2X is used for TX as well.
2.3.9.2 GPS CircuitThe RF signal is received by the antenna matched by the matching circuit. The matching circuit consists of L173, C172 on DISPLAYUnit. And this signal applied to a high-pass filter. The filter consists of C175, C177, C179, L176 and L178 on DISPLAY Unit. The filteredRF signal is then applied to a LNA Module (A151).The output of the LNA Module is fed into the SAW Filter (L359) after through the Attenuator comprised of R354, R355 and R356.The output of the second SAW filter is passed to pin L2 of the GPS IC. The input match for pin L2 comprises of C867, C866 and L852.The control and data lines for the GPS IC are GPS_PA_EN, BTFM_nSHUTDOWN, GPS_TX and GPS_RX. GPS_TX and GPS_RXare shared with Bluetooth data line.Frequency configuration for GPS is following:Lo is GPS: 1571.324MHz
Fig.9 GPS circuit
LC Filter
IC401
MPU/DSP
X401TCXO
19.2MHz
IC352 Level
Conversion
IC353 Level
Conversion
Q401 Clock Buffer
IC351
BT/GPSIC
X351 32.768kHz
Clock
L361 Bluetooth Antenna
1.8V
3.2V
OSCILLATOR
32.768kHz
GPS_TX
GPS_RXMPU/DSP
HPF Pre-SAW LNAMatching
GPS antenna
Post-SAWPost-SAW
LNA Supply
LNA ModuleTCXO
19.2MHz
ClockBuffer
Level
Conversion
GPS IC(IC850)
GPS_LNA_IN(L2)
GPS_EXT_LNA_EN(H6)
VDD_TCXO(G1)
TCXO_CLK_LV(F1)
BT_HCI_UART_TX(A4) BT_HCI_UART_RX(B5)
RTC_CLK(H9)
BTFM_nSHUTDOWN(A6)GPS PA EN(G3)
VBAT1(A2)TCXO_LDO_IN(H1)
VDDS
1-22 (No.RA053<Rev.001>)
2.4 COMPONENTS DESCRIPTION
2.4.1 TX-RX unit (XC1-178K-00,XC1-180K-00)
Ref. No. Part Name Use / Function
IC1 IC Voltage detector
IC2 IC DC/DC converter (12M)
IC3 IC DC/DC converter (38M)
IC4 IC DC/DC converter (18M)
IC5 IC Voltage regulator (32M)
IC6 IC Voltage regulator (50C)
IC7 IC Voltage regulator (32BT)
IC8 IC Voltage regulator (18BT)
IC9 IC Voltage regulator (31BU)
IC10 IC Voltage regulator (12BU)
IC11 IC Voltage regulator (32A)
IC12 IC Switch IC (18M_3 )
IC13 IC DC/DC converter (200C)
IC14 IC Voltage regulator (32C)
IC15 IC Voltage regulator (50T)
IC17 IC Voltage regulator (50A)
IC18 IC DC amplifier
IC101 IC DC amplifier (Assist)
IC102 IC DC amplifier (CV)
IC201 IC DC amplifier (Antenna SW)
IC202 IC MMIC (Pre-drive)
IC203 IC DC amplifier (APC)
IC303 IC Transceiver IC
IC351 IC GPS/Bluetooth
IC352,353 IC Level converter
IC401 IC MPU/DSP
IC402 IC SDRAM
IC403 IC Voltage detector
IC404 IC Flash memory
IC405 IC AND gate (2 input)
IC406 IC Motion sensor
IC409 IC A/D converter
IC410 IC D/A converter
IC601 IC Codec
IC650 IC Audio amplifier
IC651 IC Voltage regulator (50J)
IC652 IC Bus buffer (3 state)
IC654 IC AND gate (2 input)
Q1 Transistor 38M control
Q2 FET Detector (Power Switch)
Q3 FET Detector (BINT)
Q4 FET DC switch (SB2)
Q5 FET 18M control
Q6,7 Transistor DC switch (Codec IC)
Q102 FET DC switch (Assist)
Q103 FET DC switch (VCO Buffer)
Q111,112 FET DC switch (VCO)
Q113 Transistor Ripple filter
Q114 FET DC switch (VCO)
Q116 FET DC switch (VCO)
Q131 FET(NX-3220),Transistor(NX-3320)
VCO
Q151 Transistor VCO buffer(NX-3220),VCO(NX-3320)
Q181 Transistor VCO buffer
Q201 FET Drive amplifier
Q202 FET RF final amplifier
Q203,204 Transistor APC switch
Q205,206 FET APC switch
Q207 Transistor APC switch
Q351 FET DC switch
Q401 Transistor Clock buffer
Q402 Transistor DC switch
Q650 Transistor DC switch (Audio amplifier)
Q651,652 FET Audio mute
Q653,654 Transistor DC switch (Audio mute)
Q656 Transistor DC switch (External PTT)
D1 Diode Reverse protection
D8 Diode 38M control
D9 Diode Back up battery charge
D10 Diode DC/DC converter
D102 Zener diode Over voltage protection
D111 Diode Ripple filter
D131 Variable capacitance diode
VCO frequency control
D132-136 Variable capacitance diode
VCO frequency control
D151-155 VARI CAP D VCO frequency control
D201-203 Diode Antenna switch
D204 Zener diode Over voltage protection
D205 Diode Antenna switch
D206 Diode Surge protection
D301,302 Diode Excessive input protection
D303,304 Diode Excessive input protection
D401,402 Diode Reverse current protection
D403-407 Diode Reverse current protection
D607-609 Diode Surge protection
D620,621 Zener diode Surge protection
D650 Diode External speaker detector
D651,652 Zener diode Over voltage protection
D653-655 Diode Surge protection
Ref. No. Part Name Use / Function
(No.RA053<Rev.001>)1-23
2.4.2 Display unit (XC1-209K-XX)
2.5 TERMINAL FUNCTION
2.5.1 TX-RX unit (XC1-178K-00,XC1-180K-00)
2.5.2 Display unit (XC1-209K-XX A/2)
Ref. No. Part Name Use / Function
A151 IC GPS frontend module
IC201 IC AND gate (2 input)
Q141 Transistor DC switch (button backlight)
Q201 Transistor DC switch (LCD)
Q221-223 Transistor DC switch (TX/busy)
Q227-229 Transistor DC switch (Light bar)
D111-120 LED Button backlight
D132 LED Button backlight
D141-144 Diode Reverse current protection
D180,181 Diode Excessive input protection
D201,202 LED LCD backlight
D221 LED TX/busy
D227 LED Light bar
Pin No. Name I/O Function
CN1
1 NC - No connection
2 ENC0 I Rotary switch input
3 ENC0 I Rotary switch input
4 ENC1 I Rotary switch input
5 GND - GND
6 ENC3 I Rotary switch input
7 ENC2 I Rotary switch input
8 +B O Power output after passing throughthe fuse
9 50A O DC 5.0V output
10 VOL I Volume level input
11 GND - GND
12 SB I Switched B input
13 NC - No connection
CN7
1 /EMG I Emergency input
2 GND - GND
3 /SIDE2 I Side 2 input
4 /SIDE1 I Side 1 input
5 /PTT I PTT input
6 NC - No connection
CN402
1 32LCD O DC 3.2V output
2 32LCD O DC 3.2V output
3 18M O DC 1.8V output
4 LCD_VSS - GND
5 LCD_/CS O LCD CS signal
6 LCD_A0 O Data/Command control signal
7 LCD_E O LCD read signal
8 WR0_R/W O LCD write signal
9 LCD_/RST O LCD reset signal
10 LCD_DB0 I/O LCD Data Bus 0
11 LCD_DB1 I/O LCD Data Bus 1
12 LCD_DB2 I/O LCD Data Bus 2
13 LCD_DB3 I/O LCD Data Bus 3
14 LCD_DB4 I/O LCD Data Bus 4
15 LCD_DB5 I/O LCD Data Bus 5
16 LCD_DB6 I/O LCD Data Bus 6
17 LCD_DB7 I/O LCD Data Bus 7
18 LCD_BLC O LCD backlight control
19 GND - GND
20 GND - GND
21 ME - MIC GND
22 MIC I Main MIC input
23 50A O DC 5.0V output
24 50A O DC 5.0V output
25 /KEYI4 I Key matrix input
26 /KEYI3 I Key matrix input
27 /KEYI2 I Key matrix input
28 /KEYI1 I Key matrix input
29 /KEYI0 I Key matrix input
30 KEYO3 O Key matrix output
31 KEYO2 O Key matrix output
32 KEYO1 O Key matrix output
33 KEYO0 O Key matrix output
34 LED_G O LED Green control
35 LED_B O LED Red control
36 LED_R O LED Blue control
37 LBC_G O Light Bar Green Control
38 LBC_R O Light Bar Red Control
39 LBC_B O Light Bar Blue Control
40 GND - GND
41 GND - GND
CN602
1 SP- O BTL output for internal speaker -
2 SP+ O BTL output for internal speaker +
Pin No. Name I/O Function
CN201
1 NC - No connection
2 K- - Cathode for backlight(GND)
3 A+ O Anode for backlight
4 VSS - GND
Pin No. Name I/O Function
1-24 (No.RA053<Rev.001>)
2.5.3 Display unit (XC1-209K-XX B/2)
5 DB7 I/O LCD Data Bus 7
6 DB6 I/O LCD Data Bus 6
7 DB5 I/O LCD Data Bus 5
8 DB4 I/O LCD Data Bus 4
9 DB3 I/O LCD Data Bus 3
10 DB2 I/O LCD Data Bus 2
11 DB1 I/O LCD Data Bus 1
12 DB0 I/O LCD Data Bus 0
13 /RST O LCD reset signal
14 R/W O LCD write signal
15 E O LCD read signal
16 A0 O Data/Command control signal
17 /CS0 O LCD CS signal
18 VSS - GND
19 VDDI O LCD I/O Power Supply (DC 1.8V output)
20 VDDA O LCD Analog Power Supply (DC 3.2V output)
21 VB0+ - LCD bias voltage.connect a Cap. to VB0-
22 VB1+ - LCD bias voltage.connect a Cap. to VB1-
23 VB1- - LCD bias voltage.connect a Cap. to VB1+
24 VB0- - LCD bias voltage.connect a Cap. to VB0+
25 VLCD O Main LCD power supply.
CN202
1 GND - GND
2 GND - GND
3 LBC_B O Light Bar Blue Control
4 LBC_R O Light Bar Red Control
5 LBC_G O Light Bar Green Control
6 LED_R O LED Blue control
7 LED_B O LED Red control
8 LED_G O LED Green congrol
9 KEYO0 O Key matrix output
10 KEYO1 O Key matrix output
11 KEYO2 O Key matrix output
12 KEYO3 O Key matrix output
13 /KEYI0 I Key matrix input
14 /KEYI1 I Key matrix input
15 /KEYI2 I Key matrix input
16 /KEYI3 I Key matrix input
17 /KEYI4 I Key matrix input
18 50A O DC 5.0V output
19 50A O DC 5.0V output
20 MIC I Main MIC input
Pin No. Name I/O Function
21 ME - MIC GND
22 GND - GND
23 GND - GND
24 LCD_BLC O LCD backlight control
25 LCD_DB7 I/O LCD Data Bus 7
26 LCD_DB6 I/O LCD Data Bus 6
27 LCD_DB5 I/O LCD Data Bus 5
28 LCD_DB4 I/O LCD Data Bus 4
29 LCD_DB3 I/O LCD Data Bus 3
30 LCD_DB2 I/O LCD Data Bus 2
31 LCD_DB1 I/O LCD Data Bus 1
32 LCD_DB0 I/O LCD Data Bus 0
33 LCD_/RST
O LCD reset signal
34 WR0_R/W O LCD write siganl
35 WR1_E O LCD read signal
36 LCD_A0 O Data/Command control signal
37 LCD_/CS O LCD CS signal
38 LCD_VSS - GND
39 18M O DC 1.8V output
40 32LCD O DC 3.2V output
41 32LCD O DC 3.2V output
Pin No. Name I/O Function
CN301
1 /EMG I Emergency input
2 GND - GND
3 /SIDE2 I Side 2 input
4 /SIDE1 I Side 1 input
5 /PTT I PTT input
6 NC - No connection
Pin No. Name I/O Function
(No.RA053<Rev.001>)1-25
2.5.4 SP/MIC Connector Specification
PinNo.
Pin Name I/OSignalType
DescriptionRating and Condition
Parameter Min Typ Max Unit
1 PTT/RXD I Digital PTT/RXD inputZin=47kohm
VIH 2.0 - 5.3 V
VIL 0.0 - 0.8 V
Baud Rate - - 1.1875 Mbps
2 MICI I Analog External MIC inputZin=1.8kohm@1kHz
Audio Level 7.7 12.5 17.3 mV
DC Bias 2.9 V
Allowable Frequency 300 - 3000 Hz
Input impedance - 1.8 - kohm
3 NC - - - - - - - -
4 OPTDET I Digital External option detectionZin=74kohm
5 50J O Power DC 5V Output Output Voltage 4.9 5 5.1 V
Maximum OutputCurrent
- - 100 mA
6 AE - GND Ground Maximum InputCurrent
700 mA
7 TXD O Digital TXD outputZout=47kohm
VOH(Io=-5mA) 4.1 - 5.1 V
VOL(Io=5mA) 0.0 - 0.8 V
Baud Rate - - 1.1875 Mbps
8 EXTSPDET I Digital External speaker detection VIH 2.5 - 5.3 V
VIL 0.0 - 0.40 V
9 SPO O Analog Internal Audio output Maximum OutputPower
- - 1300 mW
Standard OutputPower
- 500 - mW
1-26 (No.RA053<Rev.001>)
SECTION 3DISASSEMBLY
3.1 Precautions for Waterproof• Do not remove the black sheet from the reverse side of the transceiver (refer to the illustration below). Removal of this sheet
decreases the waterproof efficiency of the transceiver and may cause malfunctions if water seeps into the transceiver.• The black packing material on the reverse side of the transceiver is important with respect to the waterproof efficiency of the
transceiver. • Do not place stickers or other materials on the shaded area that the battery contacts shown in the figure. Doing so will impair the
waterproof efficiency of the transceiver and may cause it to break down. Additionally, in order to prevent damage to the packing material, do not allow it to come in contact with foreign materials.
3.2 Precautions for Disassembly
3.2.1 Removing the selector knob and volume knob(1) Remove the CAP in the direction of the arrow. <1>(2) Using a thin tool, insert it in the hole on the selector knob
side and push the knob spring. <2>
Note:When you push the knob spring, take care not todamage the resin of the knob.
(3) Lift and remove the selector knob <3> while pushing theknob spring.
(4) Repeat steps 2 and 3 for the volume knob, to remove thevolume knob <4>.
Note:Perform the following procedures when installing theselector knob and volume knob.a) Match the direction for the hole of the knob and the
knob spring.b) Push the knob onto the knob spring until a click
sounds.
3.2.2 Removing the selector knob spring and volume knobspring
(1) Lightly grasp the left and right sides of the selector knobspring together, and lift up as shown in the figure. <1>
Note:Do not grasp the knob spring tightly.
(2) Remove the selector knob spring <2>.
Note:Use minimal contact with your fingers on the knobspring.
(3) Repeat steps 1 and 2 for the volume knob spring, toremove the volume knob spring <3>.
Sheet
Packing
CAP
<1>
<2><2>
<3><4>
(No.RA053<Rev.001>)1-27
3.2.3 Removing the mechanical stopper (without LCDmodels only)
(1) Pick up and lift the tab of a mechanical stopper using a pairof tweezers.
Note:Take care not to damage the packing.
(2) Remove the mechanical stopper. <1>
3.2.4 Removing the front case from the chassis(1) Remove the rear panel with a flat-head screwdriver.
Insert the screwdriver between the rear panel (right side)and the chassis, push it in the direction of the arrow<1>,and remove the right side of the rear panel. Repeat theabove action for the left side of the rear panel <2>.
(2) Remove the two screws <3>.(3) Peel off the void seal.(4) Lift the base of the chassis and remove the chassis from
the front case. <4>
Note:• Once the void seal is peeled off, it cannot be used
again.• When the chassis cannot be removed from the front
case, remove by pushing in the button top with thefinger.
• Regarding VOID, confirm the service policy of the NX-3220 and NX-3320 to KENWOOD (or authorizeddistributor).
3.2.5 Remove the holder ASSY from the chassis(1) Remove the four tabs on the holder ASSY from the
chassis.<1>(2) Lift up the holder ASSY, then remove the speaker lead wire
from the connector (CN602).
3.2.6 Removing the Display unit from the chassis(1) Remove the five screws <1>.(2) While lifting the Display unit, remove the FPC from the
connector (CN202) of the Display unit.
<1><1> Mechanical stopper
<1>
Rear panel
<2>
VOID seal
<3><3>
<4>
<1>
<1><1>
<1>
CN602CN602
the holder ASSYSpeaker lead wire from
FPC
TX-RX unit
-
Display unit<1><1>
<1>
<1>
<1>
1-28 (No.RA053<Rev.001>)
3.2.7 Removing the TX-RX unit from the chassis(1) Remove the following parts in numerical order.
<1>PACKING ASSY <2>VOL/SEL FPC <3>PTT FPC<4> nine screws
Note:The FPC is locked with an actuator.Raise the actuator straight upward, then make surethe actuator is perpendicular to the insulator.
3.2.8 Removing the TOP packing(1) Pull the TOP packing to the left to remove the packing that
is fit into the left groove of the chassis. <1>(2) Pull the TOP packing to the right to remove the packing that
is fit into the right groove of the chassis. <2>(3) Pull the TOP packing to the center to remove the packing
that is fit into the center groove of the chassis. <3>(4) Remove the TOP packing. <4>
Note:Remove the packing slowly, as the packing of theselector part might be overset when the TOP packingis removed.If the packing is turned over, return it to the originalposition using a soft tipped item (e.g., your finger).
<4><4>
<4>
<4>
<4>
<4>
<4>
<4><4>
<1>PACKING ASSY
<3>PTT FPC<2>VOL/SEL FPC
perpendicularstraight upward
Actuator
Insulator
Front contact
<4>
<1>
<2><3>
TOP packing
(No.RA053<Rev.001>)1-29
3.2.9 Removing the TERMINAL BLOCK (with PACKING)(1) Remove the screw. <1>(2) Remove the TERMINAL BLOCK (with PACKING). <2>
3.2.10 Removing the stopper of the selector circle nut andvolume circle nut
(1) Remove the stopper using a pair of tweezers. <1>(2) Remove the circular nut <2> using the nut wrench (W05-
1123-00).
Note:When reassembling, make sure the stopper and thecircular nut are engaged.
3.2.11 Removing the LCD from the Display unit(1) Remove the LCD FPC from the connector. <1>(2) Remove the Display ASSY fixed with two tabs.<2>(3) Remove the shielding case fixed with four tabs.<3>(4) Take the LCD out of the case.
3.2.12 Forming the FPC (for connection of DISPLAY UNITand TX-RX UNIT)
Bend the FPC twice along the mark. <1> <2>
3.2.13 Insert direction for the FPC (for connection ofDISPLAY UNIT and TX-RX UNIT)
Insert the FPC with the electrode surface downward.
<2>
<1>
TERMINAL BLOCK
Stopper
<1>Circular nut <2>
<2>tab
<2>tab
LCD FPC
<3>tab<3>tab
<3>tab<3>tab
LCD
Case
Mark
<2>
<1>
Mark
Display unit
1-30 (No.RA053<Rev.001>)
3.3 Precautions for Reassembly
3.3.1 Assembly Information (Sheet/Cushion)When “Main Parts” is changed (ordered), “Assembled Sheet / Cushion” should also be changed (ordered) together.The Sticker and Sheet etc are non-reusable parts. It requires the new one to get the radio’s performance after repairs.
Main Parts Assembled Sheet/ Cushion
Part Name Part Number Part Name Part Number
CHASSIS A1A-0105-00 SHEET G1A-0063-00
CUSHION G1D-0204-00
SHEET G11-4440-04
SHEET (PTT) G1G-0075-00
CUSHION (ANT) G13-2220-04
CABINET ASSY (BASIC) A0C-0177-00 STICKER (NEXEDGE) B42-7417-04
KENWOOD BADGE B4D-0044-00
FIBROUS SHEET G1A-0053-00
CABINET ASSY (STANDARD) A0C-0178-00 STICKER (NEXEDGE) B42-7417-04
KENWOOD BADGE B4D-0044-00
FIBROUS SHEET G1A-0053-00
CABINET ASSY (FULL) A0C-0179-00 STICKER (NEXEDGE) B42-7417-04
KENWOOD BADGE B4D-0044-00
FIBROUS SHEET G1A-0053-00
HOLDER J1K-0493-00 SHEET (MIC) G1A-0057-00
CUSHION (SP) G1D-0203-00
SHEET (BUTTON) G1G-0076-00
SHEET (SP) G1G-0077-00
SHEET (STD model only) G1G-0080-00
ANTENNA ELEMENT (GPS) T9A-0058-00
ANTENNA ELEMENT (BT) T9A-0059-00
MOUNTING HARDWARE J2B-0350-00 CUSHION G1D-0205-00
SHEET (LCD) G1B-0300-00
HOLDER J1K-0494-00 CUSHION G1D-0231-00
ILLUMINATION GUIDE B1B-0105-00 REFLECTION SHEET B1B-0110-00
TX-RX UNIT (NX-3220 K2,K3)TX-RX UNIT (NX-3220 E,E2) TX-RX UNIT (NX-3320 K2,K3)TX-RX UNIT (NX-3320 E,E2)
XCA-029K-00XCA-029E-01XCA-030K-00XCA-030E-01
CUSHION G1D-0272-00
(No.RA053<Rev.001>)1-31
SECTION 4ADJUSTMENT
4.1 NX-3220(K, K2, K3) TYPE Controls
4.1.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 8ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.2 Panel Test Mode (K2 and K3 types only)
4.2.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the “Panel Test”. Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the channel selectedwith the 4-way D-pad and the last used signaling number aredisplayed. When it is activated for the first time, the signalingnumber is 1.
4.2.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Auxiliary (orange) button
PTT (Push-To-Talk) switch
Side 1 button
Side 2 button
Selector knob Power switch/ Volume control
Transmit/ Receive/ Battery low indicator Light Bar
4-way D-pad
Button "Func" not appears on the sub LCD display
Function Display
[Selector] - -
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide/Narrow/Very Narrow
Wide: "w"Narrow: "n"Very Narrow: "v"
[Side1] - -
[Side2] - -
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] - -
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[AUX(Orange)]
MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
1-32 (No.RA053<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.2.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) Signaling
Analog Type Signaling
Button "Func" appears on the sub LCD display
Function Display
[Selector] - -
[] Function off -
[] Analog/NXDN/DMR Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The position of the selector knob, etc., appear.
[Side1] Function off -
[Side2] Function off -
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] Function off -
[ ] Function off -
[AUX(Orange)]
Compander On/Off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range136~174MHz
Temperature [oC] Power
An : Analog narrow modeAw : Analog wide 5k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
Squelch level(Analog mode only)
Sub LCD display
Main LCD display SignalingNo.
Channel No.
Battery type detect"ALKALI": Alkaline battery pack
"LI ": Li-ion"NIMH": Ni-MH"SP": Other
Kx types are displayed as "K".
(After 2sec.)
CH RX (MHz) TX (MHz)
1 155.05000 155.10000
2 136.05000 136.10000
3 173.95000 173.90000
4 155.00000 155.00000
5 155.20000 155.20000
6 155.40000 155.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
(No.RA053<Rev.001>)1-33
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.3 Panel Tuning Mode (K2 and K3 types only)4.3.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ ] button to write tuning data throughtuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.
• LCD display in panel tuning mode
4.3.2 Button operation
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
No. RX TX
Button Function
Push Hold (1 second)
[Selector] -
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide/Narrow/NXDN/DMR -
[ Side1 ] -
[ Side2 ] -
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Writes the adjustment value
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5 or 9 point adjustment: Adjustment point change)
[AUX(Orange)]
- -
[PTT] Transmit
[0] to [9]and[#],[ ]
-
An AST 256
2.6
CV voltage, AD value, etc
Sub LCD display
L1
Adjustment point
Main LCD display
Adjustment value(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k mode *1Nn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3C1C2C3
H1H2H3
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims at production for factory, or a operation verification of the transceiver. It is not necessary in operation of the transceiver to adjust.
1-34 (No.RA053<Rev.001>)
4.3.3 5 or 9 reference level adjustments frequency
High Transmit Power, Medium Transmit Power, LowTransmit Power, Balance, Maximum Deviation, NXDNHigh Deviation, DMR High Deviation, QT Deviation,DQT Deviation, LTR Deviation, DTMF Deviation, SingleTone Deviation, MSK Deviation, CW ID Deviation, IQPhase, RSSI Reference 1 DSP (Receive), RSSIReference 2 RF IC (Receive), RSSI Reference 3 DSP(Standby), RSSI Reference 4 RF IC (Standby), SquelchOpen, Squelch Tight, Low RSSI, High RSSI
VCO Assist
4.3.4 Adjustment item supplement
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L3 145.55000 145.60000
3 C2 155.05000 155.10000
4 H1 164.55000 164.60000
5 H3 173.95000 173.90000
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L2 140.80000 140.85000
3 L3 145.55000 145.60000
4 C1 150.30000 150.35000
5 C2 155.05000 155.10000
6 C3 159.80000 159.85000
7 H1 164.55000 164.60000
8 H2 169.30000 169.35000
9 H3 173.95000 173.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power Medium Transmit Power is adjusted.
Low Transmit Power Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviation of 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5K/Wide 4K/Narrow)
Maximum Deviation of Analog (Wide 5K/Wide 4K/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
Battery Warning Battery Warning Level (LED blinking level) is adjusted.Battery Warning Level minus 0.4V is thetransmission inhibited level.
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must be adjusted. (The curve data of RSSI level is applied.)
High RSSI
Adjustment Item Description
(No.RA053<Rev.001>)1-35
4.3.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 9 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
5 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
6 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
7 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 11~1024
8 Balance BAL (Encode frequency) - - 5 - - - TransmitterSection 51~1024
9 Maximum Deviation
ADEV - 5 5 *2 5 - - - TransmitterSection 61~1024
10 NXDN High Deviation
NDEV - - - - 5 5 - TransmitterSection 71~1024
11 DMR High Deviation
DDEV - - - - - - 5 TransmitterSection 81~1024
12 QT Deviation QT - 5 5 *2 5 - - - TransmitterSection 91~1024
13 DQT Deviation DQT - 5 5 *2 5 - - - TransmitterSection 101~1024
14 LTR Deviation LTR - 5 5 *2 5 - - - TransmitterSection 111~1024
15 DTMF Deviation DTMF - 5 5 *2 5 - - - TransmitterSection 121~1024
16 Single Tone Deviation
TONE - 5 5 *2 5 - - - TransmitterSection 131~1024
17 MSK Deviation MSK - 5 5 *2 5 - - - TransmitterSection 141~1024
18 CW ID Deviation CWID - - - 5 - - - TransmitterSection 151~1024
19 Battery Warning BATT (BATT measurement value)
1 point ADJ TransmitterSection 161~256
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
1-36 (No.RA053<Rev.001>)
*2: Wide 4k can be set up only when the PC test mode is used.
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 *2 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 *2 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
(No.RA053<Rev.001>)1-37
4.3.6 Panel tuning mode flow chart
Note:* In this Panel tuning mode flow chart, the Adjustment item name is modified.
SQL An SQL Aw SQL NnSquelch (Open) Narrow Squelch (Open) Wide Squelch (Open) Narrow
Panel Test Mode
[ ]hold LCD Contrast
CNTR
level ecnerefer 9VCO Assist stnemtsujdAAST
RTC CorrectionRTC
Ramp OffsetRAMP
High Power Narrow 5 reference levelH_PWR An Adjustments
Medium Power Narrow 5 reference levelM_PWR An Adjustments
Low Power Narrow 5 reference levelL_PWR An Adjustments
Balance Narrow 5 reference levelBAL An Adjustments
Analog Max Deviation Narrow Analog Max Deviation WideADEV An ADEV Aw
5 reference levelAdjustments
5 reference levelAdjustments
5 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
QT Deviation Narrow QT Deviation WidewATQnATQ
5 reference levelAdjustments
DQT Deviation Narrow DQT Deviation WideDQT An DQT Aw
5 reference levelAdjustments
LTR Deviation Narrow LTR Deviation WidewARTLnARTL
5 reference levelAdjustments
DTMF Deviation Narrow DTMF Deviation WideDTMF An DTMF Aw
5 reference levelAdjustments
MSK Deviation Narrow MSK Deviation WideMSK An MSK Aw
5 reference levelAdjustments
CW ID Deviation NarrowCWID An
BatteryBATT
Squelch (Open) DMR
5 reference levelAdjustments
RSSI (Low) NarrownAISSRL
RSSI (High) NarrownAISSRH
Adjustment Item N/W/VNLCD DisplayFor all adjustment items, press the [ ] buttonto write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ] [ ] [ ] [ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]
5 reference levelAdjustments
[ ]
RSSI Referance 1RSSI1
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]IQ PhaseIQ
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 2RSSI2
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 3RSSI3
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 4RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
Single Tone Deviation Narrow Single Tone Deviation WideTONE An TONE Aw
5 reference levelAdjustments
[ ] [ ][ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
DMR High DeviationDDEV
[ ]press [ ]hold
[ ]
[ ] [ ] [ ]
Adjustment PointLCD Display
5 reference levelL1
L3
C2
H3
H1
Low 1Adjustments
Low 3
Center 2
High 3
5 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 1 [ ]
[ ]
[ ]
High Transmit PowerMedium Transmit PowerLow Transmit Power
Maximum Deviation NXDN High DeviationDMR High DeviationQT DeviationDQT DeviationLTR DeviationDTMF DeviationSingle Tone DeviationMSK DeviationCW ID DeviationIQ PhaseRSSI Reference 1RSSI Reference 2RSSI Reference 3RSSI Reference 4Open Squelch
Low RSSIHigh RSSI
Tight Squelch
Adjustment PointLCD Display
9 reference levelL1
L2
L3
H3
C1
C2
C3
H1
H2
Low 1Adjustments
Low 2
Low 3
High 3
9 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]Center 2
Center 3
[ ]
[ ][ ]
[ ]High 1 [ ]
[ ]High 2 [ ]
[ ]
[ ]
Balance
VCO Assist
VeryNarrow
Squelch (Tight) Narrow Squelch (Tight) WidewATLQSnATLQS
5 reference levelAdjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
TLSn5 reference levelAdjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
[ ]press [ ]hold
DMRD
Squelch (Open)Nv D
[ ]
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
[ ]
1-38 (No.RA053<Rev.001>)
4.4 Adjustment points
TX-RX UNIT (XC1-178)Component Side
4.5 Test Equipment Required for Alignment
* The test equipment which is not used for adjustment is contained in this table.
RTC (CN412)
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.003ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 10W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 10V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 5A
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 8ohm Dummy Load Approx. 8ohm, 3W
13. Regulated Power Supply 5V to 10V, approx. 3A, Useful if ammeter equipped
(No.RA053<Rev.001>)1-39
Antenna connector adapterThe antenna connector of this transceiver uses an SMAterminal.Use an antenna connector adapter [SMA(f) - BNC(f) or SMA(f)- N(f)] for adjustment. (The adapter is not provided as anoption, so buy a commercially-available one.)
Nut wrenchIn order to turn the volume nut and the channel selector nut,use a recommendation tool.KENWOOD part No.: W05-1123-00
Battery Jig (W05-0909-00)Connect the power cable properly between the battery jiginstalled in the transceiver and the power supply, and be sureoutput voltage and the power supply polarity prior to switchingthe power supply ON, otherwise over voltage and reverseconnection may damage the transceiver, or the power supplyor both.When using the battery jig in user mode, the transceiverassumes that a lithium-ion battery pack is attached to thetransceiver. In adjustment mode, battery type detection is notperformed.
Note: When using the battery jig, you must measure the voltageat the terminals of the battery jig. Otherwise, a slightvoltage drop may occur within the power cable, betweenthe power supply and the battery jig, especially while thetransceiver transmits.
4.6 Radio check Section
+ Terminal (Red)
– Terminal (Black)
S
–
+
C1
10
0P
/25
V
C2
47
0P
/25
V
C3
10
0µ
/25
V
R1
1.8
M
+
(Red)+Terminal
–Terminal(Black)
supplyPowerPower
cable
Schematic diagram
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.5ppm±[email protected]
2. High power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 4.0~6.0W2.0A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
1-40 (No.RA053<Rev.001>)
4.7 Common Section
3. Low power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 0.7~1.4W1.0A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
Deviation meterOscilloscopeAGAF VM
Panel ANTSP/MIC connector
Adjust AG input to get a standard MOD.
12.5mV±5.8mV
5. Sensitivity check
1)CH-Sig: 1-1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortion meter8ohm Dummy load
Panel ANTSP/MIC connector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:7.5V2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
126 (Reference value)
(No.RA053<Rev.001>)1-41
3. VCO Assist
1) Adj item:[AST]Adjust:[****]2) Adj item:[L1]→[L2]→[L3]→[C1]→[C2]→[C3]→[H1]→[H2]→[H3]→
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]2) Adj item:[Low1],[Low2], [Low3], [Center1], [Center2], [Center3], [High1],[High2][High3]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.003ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±10 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-42 (No.RA053<Rev.001>)
4.8 Transmitter Section
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]
Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN412)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. High transmit power (Battery voltage : 7.5V)
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5.0W ±0.1W 2.0A or less
2. Medium transmit power (Battery voltage : 7.5V)
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
4.0W ±0.1W 2.0A or less
3. Low transmit power (Battery voltage : 7.5V)
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
1.0W ±0.1W 1.0A or less
(No.RA053<Rev.001>)1-43
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX Starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
[Manual Adjustment]1) Set the adjustment
value to “1”.2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed “51”.
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.
[Panel tuning mode]PTT: ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.
[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-44 (No.RA053<Rev.001>)
6. Maximum Deviation
[Analog Wide]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [OK] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “498” for each adjustment point.Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz. Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-45
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
9. QT Deviation
[Analog Wide]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.517 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-46 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.517 (Reference value)
0.35kHz±0.05kHz
10. DQT Deviation
[Analog Wide]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.415 (Reference value)
0.75kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.415 (Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-47
11. LTR Deviation
[Analog Wide]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.508 (Reference value)
1.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.496 (Reference value)
0.75kHz±0.05kHz
12. DTMF Deviation
[Analog Wide]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.547 (Reference value)
2.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-48 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.547 (Reference value)
1.25kHz±0.05kHz
13. Single Tone Deviation
[Analog Wide]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.515 (Reference value)
3.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.514 (Reference value)
1.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-49
14. MSK Deviation
[Analog Wide]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.505 (Reference value)
3.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.505 (Reference value)
1.50kHz±0.05kHz
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.511 (Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-50 (No.RA053<Rev.001>)
16. Battery Warning writing
1) Adj item:[BATT]Adjust:[****]BATT terminal voltage: 6.2V while transmitting.
1) Adj item: [Battery Warning]BATT terminal voltage: 6.2V while transmitting.
Power meterDVM
Panel ANTBATT terminal
[Panel tuning mode]PTT: ONPress [ ] button to store the adjustment value.
[PC test mode]1) Press [Transmit]
button.2) Press [Acquire
Monitored Value] button.
3) Press [Apply] button to store the adjustment value.Confirm that one predetermined numeric in the range 1 to 256 appears.
17. Battery Warning check
[Panel test mode]1) CH-Sig: 1-1
BATT terminal voltage: 6.0V while transmitting.
[Panel test mode]1) Test Channel
Channel: 1Test SignalingType: AnalogSignaling: 1BATT terminal voltage: 6.0V while transmitting.
Check The transceiver can transmit with causing the LED to blink.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-51
4.8.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide)", this signaling is composed of three elements [Balance, Maximum Deviation(Analog Wide) and QT Deviation (Analog Wide)]. Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QTDeviation (Analog Wide).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 5) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide/Narrow) is common with all the analog signaling deviations and CWID Deviation (NXDN VeryNarrow).If Balance and Maximum Deviation (Analog Wide /Narrow) (Transmitter Section 6) have already adjusted, please skip Step2 andadjust from Step3.
Mode Signaling Necessary adjustment and order
Wide Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. QT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation [Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DQT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. LTR Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation [Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DTMF Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation [Analog Narrow]
-
2TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. Single Tone Deviation [Analog
Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide]3. MSK Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High Deviation
[NXDN Very Narrow]
CWID - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - 1. Balance adjust2. DMR High Deviation
-
1-52 (No.RA053<Rev.001>)
4.9 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTSP/MIC connector
Panel Volume knob
Turn the Volume knob to obtain 0.63V AF output.
0.63V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[Panel tuning mode]After input signal from SSG, Increase or decrease the adjustment value so that the RSSI indicator level becomes minimum.[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
(No.RA053<Rev.001>)1-53
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-54 (No.RA053<Rev.001>)
4. Squelch Open
[Analog Wide]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-55
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-56 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-57
4.10 NX-3220(E, E2, E3) TYPE Controls
4.10.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 8ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.11 Panel Test Mode (E and E2 types only)
4.11.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the “Panel Test”. Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the channel selectedwith the 4-way D-pad and the last used signaling number aredisplayed. When it is activated for the first time, the signalingnumber is 1.
4.11.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Auxiliary (orange) button
PTT (Push-To-Talk) switch
Side 1 button
Side 2 button
Selector knob Power switch/ Volume control
Transmit/ Receive/ Battery low indicator Light Bar
4-way D-pad
Button "Func" not appears on the sub LCD display
Function Display
[Selector] - -
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide 5k/Wide 4k/Narrow/Very Narrow
Wide 5k: "w"Wide 4k: "s"Narrow: "n"Very Narrow: "v"
[Side1] - -
[Side2] - -
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] - -
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[AUX(Orange)]
MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
1-58 (No.RA053<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.11.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) Signaling
Analog Type Signaling
Button "Func" appears on the sub LCD display
Function Display
[Selector] - -
[] Function off -
[] Analog/NXDN/DMR Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The position of the selector knob, etc., appear.
[Side1] Function off -
[Side2] Function off -
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] Function off -
[ ] Function off -
[AUX(Orange)]
Compander On/Off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range136~174MHz
Temperature [oC] Power
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
Squelch level(Analog mode only)
Sub LCD display
Main LCD display SignalingNo.
Channel No.
Battery type detect"ALKALI": Alkaline battery pack
"LI ": Li-ion"NIMH": Ni-MH"SP": Other
Ex type aredisplayed as "E".
(After 2sec.)
CH RX (MHz) TX (MHz)
1 155.05000 155.10000
2 136.05000 136.10000
3 173.95000 173.90000
4 155.00000 155.00000
5 155.20000 155.20000
6 155.40000 155.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
(No.RA053<Rev.001>)1-59
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.12 Panel Tuning Mode (E and E2 types only)4.12.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ ] button to write tuning data throughtuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.
• LCD display in panel tuning mode
4.12.2 Button operation
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
No. RX TX
Button Function
Push Hold (1 second)
[Selector] -
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide 5k/Wide 4k/Narrow/NXDN/DMR
-
[ Side1 ] -
[ Side2 ] -
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Writes the adjustment value
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5 or 9 point adjustment: Adjustment point change)
[AUX(Orange)]
- -
[PTT] Transmit
[0] to [9]and[#],[ ]
-
An AST 256
2.6
CV voltage, AD value, etc
Sub LCD display
L1
Adjustment point
Main LCD display
Adjustment value(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3C1C2C3
H1H2H3
1-60 (No.RA053<Rev.001>)
4.12.3 5 or 9 reference level adjustments frequency
High Transmit Power, Medium Transmit Power, LowTransmit Power, Balance, Maximum Deviation, NXDNHigh Deviation, DMR High Deviation, QT Deviation,DQT Deviation, LTR Deviation, DTMF Deviation, SingleTone Deviation, MSK Deviation, CW ID Deviation, IQPhase, RSSI Reference 1 DSP (Receive), RSSIReference 2 RF IC (Receive), RSSI Reference 3 DSP(Standby), RSSI Reference 4 RF IC (Standby), SquelchOpen, Squelch Tight, Low RSSI, High RSSI
VCO Assist
4.12.4 Adjustment item supplement
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L3 145.55000 145.60000
3 C2 155.05000 155.10000
4 H1 164.55000 164.60000
5 H3 173.95000 173.90000
Tuning point Display RX (MHz) TX (MHz)
1 L1 136.05000 136.10000
2 L2 140.80000 140.85000
3 L3 145.55000 145.60000
4 C1 150.30000 150.35000
5 C2 155.05000 155.10000
6 C3 159.80000 159.85000
7 H1 164.55000 164.60000
8 H2 169.30000 169.35000
9 H3 173.95000 173.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power Medium Transmit Power is adjusted.
Low Transmit Power Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviation of 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5K/Wide 4K/Narrow)
Maximum Deviation of Analog (Wide 5K/Wide 4K/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
Battery Warning Battery Warning Level (LED blinking level) is adjusted.Battery Warning Level minus 0.4V is thetransmission inhibited level.
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must be adjusted. (The curve data of RSSI level is applied.)
High RSSI
Adjustment Item Description
(No.RA053<Rev.001>)1-61
4.12.5 Adjustment item and Display
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 9 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
5 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
6 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
7 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 11~1024
8 Balance BAL (Encode frequency) - - 5 - - - TransmitterSection 51~1024
9 Maximum Deviation
ADEV - 5 5 5 - - - TransmitterSection 61~1024
10 NXDN High Deviation
NDEV - - - - 5 5 - TransmitterSection 71~1024
11 DMR High Deviation
DDEV - - - - - - 5 TransmitterSection 81~1024
12 QT Deviation QT - 5 5 5 - - - TransmitterSection 91~1024
13 DQT Deviation DQT - 5 5 5 - - - TransmitterSection 101~1024
14 LTR Deviation LTR - 5 5 5 - - - TransmitterSection 111~1024
15 DTMF Deviation DTMF - 5 5 5 - - - TransmitterSection 121~1024
16 Single Tone Deviation
TONE - 5 5 5 - - - TransmitterSection 131~1024
17 MSK Deviation MSK - 5 5 5 - - - TransmitterSection 141~1024
18 CW ID Deviation CWID - - - 5 - - - TransmitterSection 151~1024
19 Battery Warning BATT (BATT measurement value)
1 point ADJ TransmitterSection 161~256
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
1-62 (No.RA053<Rev.001>)
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
(No.RA053<Rev.001>)1-63
4.12.6 Panel tuning mode flow chart
Note:* In this Panel tuning mode flow chart, the Adjustment item name is modified.
Panel Test Mode
[ ]hold LCD Contrast
CNTR
level ecnerefer 9VCO Assist stnemtsujdAAST
RTC CorrectionRTC
Ramp OffsetRAMP
High Power Narrow 5 reference levelH_PWR An Adjustments
Medium Power Narrow 5 reference levelM_PWR An Adjustments
Low Power Narrow 5 reference levelL_PWR An Adjustments
Balance Narrow 5 reference levelBAL An Adjustments
5 reference levelAdjustments
5 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
CW ID Deviation NarrowCWID An
BatteryBATT
RSSI (Low) NarrownAISSRL
RSSI (High) NarrownAISSRH
Adjustment Item N/W/VNLCD DisplayFor all adjustment items, press the [ ] buttonto write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]
5 reference levelAdjustments
[ ]
RSSI Referance 1RSSI1
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]IQ PhaseIQ
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 2RSSI2
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 3RSSI3
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 4RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
DMR High DeviationDDEV
[ ]press [ ]hold
Adjustment PointLCD Display
5 reference levelL1
L3
C2
H3
H1
Low 1Adjustments
Low 3
Center 2
High 3
5 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 1 [ ]
[ ]
[ ]
High Transmit PowerMedium Transmit PowerLow Transmit Power
Maximum Deviation NXDN High DeviationDMR High DeviationQT DeviationDQT DeviationLTR DeviationDTMF DeviationSingle Tone DeviationMSK DeviationCW ID DeviationIQ PhaseRSSI Reference 1RSSI Reference 2RSSI Reference 3RSSI Reference 4Open Squelch
Low RSSIHigh RSSI
Tight Squelch
Adjustment PointLCD Display
9 reference levelL1
L2
L3
H3
C1
C2
C3
H1
H2
Low 1Adjustments
Low 2
Low 3
High 3
9 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]Center 2
Center 3
[ ]
[ ][ ]
[ ]High 1 [ ]
[ ]High 2 [ ]
[ ]
[ ]
Balance
VCO Assist
[ ]press [ ]hold
DMRD
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
Analog Max Deviation Narrow Analog Max Deviation Wide4k Analog Max Deviation Wide5kADEV An ADEV As ADEV Aw
[ ]
[ ] [ ] [ ]
[ ] [ ]
[ ]press [ ]hold
Single Tone Deviation Narrow Single Tone Deviation Wide4kTONE An TONE Aw
[ ] [ ][ ]press [ ]hold
[ ]
MSK Deviation Narrow MSK Deviation Wide4k MSK Deviation Wide5k
MSK An MSK As MSK Aw5 reference levelAdjustments
[ ]
[ ]
QT Deviation Narrow QT Deviation Wide4ksATQnATQ
DQT Deviation Narrow DQT Deviation Wide4kDQT An DQT As
LTR Deviation Narrow LTR Deviation Wide4ksARTLnARTL
DTMF Deviation Narrow DTMF Deviation Wide4kDTMF An DTMF As
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]5 reference level
[ ]
QT Deviation Wide5kQT Aw
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
DQT Deviation Wide5kDQT Aw
5 reference levelAdjustments
LTR Deviation Wide5kLTR Aw
DTMF Deviation Wide5kDTMF Aw
Adjustments
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
[ ]
5 reference level
[ ]Single Tone Deviation Wide5kTONE Aw
Adjustments[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]
Squelch (Open) Narrow Squelch (Open) Wide4k Squelch (Open) Wide5k Squelch (Open)SQL An SQL As SQL Aw SQL
[ ]
[ ] [ ] [ ] [ ] [ ]
[ ] [ ] [ ] [ ]
[ ]
5 reference levelAdjustments
VeryNarrow
NvNarrow
Nn
Squelch (Open)
DMRD
Squelch (Open)[ ]press [ ]hold
[ ]Squelch (Tight) Narrow Squelch (Tight) Wide4k Squelch (Tight) Wide5kwATLQSsATLQSnATLQS
5 reference levelAdjustments
[ ] [ ] [ ]
[ ] [ ]
1-64 (No.RA053<Rev.001>)
4.13 Adjustment points
TX-RX UNIT (XC1-178)Component Side
4.14 Test Equipment Required for Alignment
* The test equipment which is not used for adjustment is contained in this table.
RTC (CN412)
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.003ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 10W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 10V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 5A
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 8ohm Dummy Load Approx. 8ohm, 3W
13. Regulated Power Supply 5V to 10V, approx. 3A, Useful if ammeter equipped
(No.RA053<Rev.001>)1-65
Antenna connector adapterThe antenna connector of this transceiver uses an SMAterminal.Use an antenna connector adapter [SMA(f) - BNC(f) or SMA(f)- N(f)] for adjustment. (The adapter is not provided as anoption, so buy a commercially-available one.)
Nut wrenchIn order to turn the volume nut and the channel selector nut,use a recommendation tool.KENWOOD part No.: W05-1123-00
Battery Jig (W05-0909-00)Connect the power cable properly between the battery jiginstalled in the transceiver and the power supply, and be sureoutput voltage and the power supply polarity prior to switchingthe power supply ON, otherwise over voltage and reverseconnection may damage the transceiver, or the power supplyor both.When using the battery jig in user mode, the transceiverassumes that a lithium-ion battery pack is attached to thetransceiver. In adjustment mode, battery type detection is notperformed.
Note: When using the battery jig, you must measure the voltageat the terminals of the battery jig. Otherwise, a slightvoltage drop may occur within the power cable, betweenthe power supply and the battery jig, especially while thetransceiver transmits.
4.15 Radio check Section
+ Terminal (Red)
– Terminal (Black)
S
–
+
C1
10
0P
/25
V
C2
47
0P
/25
V
C3
10
0µ
/25
V
R1
1.8
M
+
(Red)+Terminal
–Terminal(Black)
supplyPowerPower
cable
Schematic diagram
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
±0.5ppm±[email protected]
2. High power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 4.0~6.0W2.0A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
1-66 (No.RA053<Rev.001>)
4.16 Common Section
3. Low power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 0.7~1.4W1.0A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
Deviation meterOscilloscopeAGAF VM
Panel ANTSP/MIC connector
Adjust AG input to get a standard MOD.
12.5mV±5.8mV
5. Sensitivity check
1)CH-Sig: 1-1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k: -117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)
Narrow: -117dBm (0.32μV)
(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k: -117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)
Narrow: -117dBm (0.32μV)
(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortion meter8ohm Dummy load
Panel ANTSP/MIC connector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:7.5V2) SSG standard modulation
[Wide 5k] MOD:1kHz,DEV:3kHz[Wide 4k] MOD:1kHz,DEV:2.4kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
126 (Reference value)
(No.RA053<Rev.001>)1-67
3. VCO Assist
1) Adj item:[AST]Adjust:[****]2) Adj item:[L1]→[L2]→[L3]→[C1]→[C2]→[C3]→[H1]→[H2]→[H3]→
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]2) Adj item:[Low1],[Low2], [Low3], [Center1], [Center2], [Center3], [High1],[High2][High3]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.003ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±10 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-68 (No.RA053<Rev.001>)
4.17 Transmitter Section
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]
Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN412)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. High transmit power (Battery voltage : 7.5V)
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5.0W ±0.1W 2.0A or less
2. Medium transmit power (Battery voltage : 7.5V)
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
4.0W ±0.1W 2.0A or less
3. Low transmit power (Battery voltage : 7.5V)
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L3]→[C2]→[H1]→[H3]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
1.0W ±0.1W 1.0A or less
(No.RA053<Rev.001>)1-69
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX Starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
[Manual Adjustment]1) Set the adjustment
value to “1”.2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed “51”.
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.
[Panel tuning mode]PTT: ONWhile PTT:ON, press the[] button to change the 20Hz/2kHz.
[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-70 (No.RA053<Rev.001>)
6. Maximum Deviation
[Analog Wide 5k]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [OK] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Wide 4k]
1) Adj item: [As ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [OK] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 3310Hz and 3410Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
3310~3410Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-71
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “498” for each adjustment point.Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz. Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “497” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-72 (No.RA053<Rev.001>)
9. QT Deviation
[Analog Wide 5k]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.517 (Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.517 (Reference value)
0.60kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.517 (Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-73
10. DQT Deviation
[Analog Wide 5k]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.415 (Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.415 (Reference value)
0.60kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.415 (Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-74 (No.RA053<Rev.001>)
11. LTR Deviation
[Analog Wide 5k]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.508 (Reference value)
1.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.496 (Reference value)
0.90kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.496 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-75
12. DTMF Deviation
[Analog Wide 5k]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.547 (Reference value)
2.50kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.547 (Reference value)
2.00kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.547 (Reference value)
1.25kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-76 (No.RA053<Rev.001>)
13. Single Tone Deviation
[Analog Wide 5k]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.515 (Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.515 (Reference value)
2.40kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.514 (Reference value)
1.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-77
14. MSK Deviation
[Analog Wide 5k]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.505 (Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.505 (Reference value)
2.40kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.505 (Reference value)
1.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-78 (No.RA053<Rev.001>)
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.511 (Reference value)
1.10kHz±0.10kHz
16. Battery Warning writing
1) Adj item:[BATT]Adjust:[****]BATT terminal voltage: 6.2V while transmitting.
1) Adj item: [Battery Warning]BATT terminal voltage: 6.2V while transmitting.
Power meterDVM
Panel ANTBATT terminal
[Panel tuning mode]PTT: ONPress [ ] button to store the adjustment value.
[PC test mode]1) Press [Transmit]
button.2) Press [Acquire
Monitored Value] button.
3) Press [Apply] button to store the adjustment value.Confirm that one predetermined numeric in the range 1 to 256 appears.
17. Battery Warning check
[Panel test mode]1) CH-Sig: 1-1
BATT terminal voltage: 6.0V while transmitting.
[Panel test mode]1) Test Channel
Channel: 1Test SignalingType: AnalogSignaling: 1BATT terminal voltage: 6.0V while transmitting.
Check The transceiver can transmit with causing the LED to blink.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-79
4.17.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide 5k)", this signaling is composed of three elements [Balance, MaximumDeviation (Analog Wide 5k) and QT Deviation (Analog Wide 5k)]. Please adjust Balance and Maximum Deviation (Analog Wide 5k)before adjusting QT Deviation (Analog Wide 5k).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 5) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) is common with all the analog signaling deviations and CWID Deviation(NXDN Very Narrow).If Balance and Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) (Transmitter Section 6) have already adjusted, please skipStep2 and adjust from Step3.
Mode Signaling Necessary adjustment and order
Wide 5k Wide 4k Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. QT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. QT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation
[Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DQT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DQT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. LTR Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. LTR Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation
[Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DTMF Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DTMF Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation
[Analog Narrow]
-
5TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. Single Tone Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. Single Tone Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. MSK Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. MSK Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High
Deviation [NXDN Very Narrow]
CWID - - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - - 1. Balance adjust2. DMR High Deviation
-
1-80 (No.RA053<Rev.001>)
4.18 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTSP/MIC connector
Panel Volume knob
Turn the Volume knob to obtain 0.63V AF output.
0.63V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[Panel tuning mode]After input signal from SSG, Increase or decrease the adjustment value so that the RSSI indicator level becomes minimum.[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
(No.RA053<Rev.001>)1-81
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-82 (No.RA053<Rev.001>)
4. Squelch Open
[Analog Wide 5k]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide 5k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Wide 4k]
1) Adj item: [As SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Open (Analog Wide 4k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-83
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-84 (No.RA053<Rev.001>)
5. Squelch Tight
[Analog Wide 5k]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide 5k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, press [Apply] button to store the adjustment value.
[Analog Wide 4k]
1) Adj item: [As SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Tight (Analog Wide 4k)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-85
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L3]→[C2]→[H1]→[H3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low3]→[Center2]→[High1]→[High3]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-86 (No.RA053<Rev.001>)
4.19 NX-3320(K, K2, K3) TYPE Controls
4.19.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 8ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.20 Panel Test Mode (K2 and K3 types only)
4.20.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the “Panel Test”. Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the channel selectedwith the 4-way D-pad and the last used signaling number aredisplayed. When it is activated for the first time, the signalingnumber is 1.
4.20.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Auxiliary (orange) button
PTT (Push-To-Talk) switch
Side 1 button
Side 2 button
Selector knob Power switch/ Volume control
Transmit/ Receive/ Battery low indicator Light Bar
4-way D-pad
Button "Func" not appears on the sub LCD display
Function Display
[Selector] - -
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide/Narrow/Very Narrow
Wide: "w"Narrow: "n"Very Narrow: "v"
[Side1] - -
[Side2] - -
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] - -
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[AUX(Orange)]
MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
(No.RA053<Rev.001>)1-87
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.20.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) Test signaling
Analog Type Signaling
Button "Func" appears on the sub LCD display
Function Display
[Selector] - -
[] Function off -
[] Analog/NXDN/DMR Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The position of the selector knob, etc., appear.
[Side1] Function off -
[Side2] Function off -
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] Function off -
[ ] Function off -
[AUX(Orange)]
Compander On/Off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range400~520MHz
Temperature [oC] Power
An : Analog narrow modeAw : Analog wide 5k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
Squelch level(Analog mode only)
Sub LCD display
Main LCD display SignalingNo.
Channel No.
Battery type detect"ALKALI": Alkaline battery pack
"LI ": Li-ion"NIMH": Ni-MH"SP": Other
Kx types are displayed as "K".
(After 2sec.)
CH K,K2,K3
RX (MHz) TX (MHz)
1 460.05000 460.10000
2 400.05000 400.10000
3 519.95000 519.90000
4 460.00000 460.00000
5 460.20000 460.20000
6 460.40000 460.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
1-88 (No.RA053<Rev.001>)
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.21 Panel Tuning Mode (K2 and K3 types only)4.21.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ ] button to write tuning data throughtuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.
• LCD display in panel tuning mode
4.21.2 Button operation
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
No. RX TX
Button Function
Push Hold (1 second)
[Selector] -
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide/Narrow/NXDN/DMR -
[ Side1 ] -
[ Side2 ] -
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Writes the adjustment value
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5, 9 or 17 point adjustment: Adjustment point change)
[AUX(Orange)]
- -
[PTT] Transmit
[0] to [9]and[#],[ ]
-
An AST 256
2.6
CV voltage, AD value, etc
Sub LCD display
L1
Adjustment point
Main LCD display
Adjustment value(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k mode *1Nn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims at production for factory, or a operation verification of the transceiver. It is not necessary in operation of the transceiver to adjust.
L1L2L3C1C2C3
H1H2H3
(No.RA053<Rev.001>)1-89
4.21.3 5, 9 or 17 reference level adjustments frequency
High Transmit Power, Medium Transmit Power, LowTransmit Power, IQ Phase, RSSI Reference 1 DSP(Receive), RSSI Reference 2 RF IC (Receive), RSSIReference 3 DSP (Standby), RSSI Reference 4 RF IC(Standby), Squelch Open, Squelch Tight, Low RSSI,High RSSI
Balance, Maximum Deviation , NXDN High Deviation, DMRHigh Deviation, QT Deviation, DQT Deviation, LTRDeviation, DTMF Deviation, Single Tone Deviation, MSKDeviation, CW ID Deviation
VCO Assist
4.21.4 Adjustment item supplement
Tuning point Display K,K2,K3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L5 430.05000 430.10000
3 C3 460.05000 460.10000
4 H2 490.05000 490.10000
5 H6 519.95000 519.90000
Tuning point Display K,K2,K3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L3 415.05000 415.10000
3 L5 430.05000 430.10000
4 C1 445.05000 445.10000
5 C3 460.05000 460.10000
6 C5 475.05000 475.10000
7 H2 490.05000 490.10000
8 H4 505.05000 505.10000
9 H6 519.95000 519.90000
Tuning point Display K,K2,K3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L2 407.55000 407.60000
3 L3 415.05000 415.10000
4 L4 422.55000 422.60000
5 L5 430.05000 430.10000
6 L6 437.55000 437.60000
7 C1 445.05000 445.10000
8 C2 452.55000 452.60000
9 C3 460.05000 460.10000
10 C4 467.55000 467.60000
11 C5 475.05000 475.10000
12 H1 482.55000 482.60000
13 H2 490.05000 490.10000
14 H3 497.55000 497.60000
15 H4 505.05000 505.10000
16 H5 512.55000 512.60000
17 H6 519.95000 519.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power Medium Transmit Power is adjusted.
Low Transmit Power Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviation of 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5K/Wide 4K/Narrow)
Maximum Deviation of Analog (Wide 5K/Wide 4K/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
Battery Warning Battery Warning Level (LED blinking level) is adjusted.Battery Warning Level minus 0.4V is thetransmission inhibited level.
1-90 (No.RA053<Rev.001>)
4.21.5 Adjustment item and Display
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must be adjusted. (The curve data of RSSI level is applied.)
High RSSI
Adjustment Item Description
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 17 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
5 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
6 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
7 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 11~1024
8 Balance BAL (Encode frequency) - - 9 - - - TransmitterSection 51~1024
9 Maximum Deviation
ADEV - 9 9 *2 9 - - - TransmitterSection 61~1024
10 NXDN High Deviation
NDEV - - - - 9 9 - TransmitterSection 71~1024
11 DMR High Deviation
DDEV - - - - - - 9 TransmitterSection 81~1024
12 QT Deviation QT - 9 9 *2 9 - - - TransmitterSection 91~1024
13 DQT Deviation DQT - 9 9 *2 9 - - - TransmitterSection 101~1024
14 LTR Deviation LTR - 9 9 *2 9 - - - TransmitterSection 111~1024
15 DTMF Deviation DTMF - 9 9 *2 9 - - - TransmitterSection 121~1024
16 Single Tone Deviation
TONE - 9 9 *2 9 - - - TransmitterSection 131~1024
(No.RA053<Rev.001>)1-91
*2: Wide 4k can be set up only when the PC test mode is used.
17 MSK Deviation MSK - 9 9 *2 9 - - - TransmitterSection 141~1024
18 CW ID Deviation CWID - - - 9 - - - TransmitterSection 151~1024
19 Battery Warning BATT (BATT measurement value)
1 point ADJ TransmitterSection 161~256
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 *2 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 *2 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide)
AS *2(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1-92 (No.RA053<Rev.001>)
4.21.6 Panel tuning mode flow chart
Note:* In this Panel tuning mode flow chart, the Adjustment item name is modified.
SQL An SQL Aw SQL NnSquelch (Open) Narrow Squelch (Open) Wide Squelch (Open) Narrow
Panel Test Mode
[ ]hold LCD Contrast
CNTR
VCO Assist AST
RTC CorrectionRTC
Ramp OffsetRAMP
High Power Narrow 5 reference levelH_PWR An Adjustments
Medium Power Narrow 5 reference levelM_PWR An Adjustments
Low Power Narrow 5 reference levelL_PWR An Adjustments
Balance NarrowBAL An
Analog Max Deviation Narrow Analog Max Deviation WideADEV An ADEV Aw
9 reference levelAdjustments
9 reference levelAdjustments
9 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
QT Deviation Narrow QT Deviation WidewATQnATQ
9 reference levelAdjustments
DQT Deviation Narrow DQT Deviation WideDQT An DQT Aw
9 reference levelAdjustments
LTR Deviation Narrow LTR Deviation WidewARTLnARTL
9 reference levelAdjustments
DTMF Deviation Narrow DTMF Deviation WideDTMF An DTMF Aw
9 reference levelAdjustments
MSK Deviation Narrow MSK Deviation WideMSK An MSK Aw
9 reference levelAdjustments
CW ID Deviation NarrowCWID An
BatteryBATT
Squelch (Open) DMR
5 reference levelAdjustments
RSSI (Low) NarrownAISSRL
RSSI (High) NarrownAISSRH
Adjustment Item N/W/VNLCD DisplayFor all adjustment items, press the [ ] buttonto write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ] [ ] [ ] [ ] [ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]
9 reference levelAdjustments
[ ]
RSSI Referance 1RSSI1
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]IQ PhaseIQ
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 2RSSI2
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 3RSSI3
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 4RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
Single Tone Deviation Narrow Single Tone Deviation WideTONE An TONE Aw
9 reference levelAdjustments
[ ] [ ][ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
DMR High DeviationDDEV
[ ]press [ ]hold
[ ]
[ ] [ ] [ ]VeryNarrow
Squelch (Tight) Narrow Squelch (Tight) WidewATLQSnATLQS
5 reference levelAdjustments
[ ] [ ][ ]press [ ]hold
[ ] [ ]
TLSn[ ] [ ][ ]press [ ]hold
[ ] [ ]
[ ]press [ ]hold
DMRD
Squelch (Open)Nv D
[ ]
17 reference levelAdjustments
9 reference levelAdjustments
IQ PhaseRSSI Reference 1RSSI Reference 2RSSI Reference 3RSSI Reference 4Open Squelch
Low RSSIHigh RSSI
Tight Squelch
VCO Assist
Maximum Deviation NXDN High DeviationDMR High DeviationQT DeviationDQT DeviationLTR DeviationDTMF DeviationSingle Tone DeviationMSK DeviationCW ID Deviation
Balance
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
[ ]
Adjustment PointLCD Display
5 reference levelL1
L5
C3
H6
H2
Low 1Adjustments
Low 5
Center 3
High 6
5 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 2 [ ]
[ ]
[ ]
High Transmit PowerMedium Transmit PowerLow Transmit Power
Adjustment PointLCD Display
9 reference levelL1
L3
L5
H6
C1
C3
C5
H2
H4
Low 1Adjustments
Low 3
Low 5
High 6
9 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]Center 3
Center 5
[ ]
[ ][ ]
[ ]High 2 [ ]
[ ]High 4 [ ]
[ ]
[ ]
Adjustment PointLCD Display
17 reference levelL1
L2
L3
L4
L5
L6
C1
C2
C3
C4
C5
H1
H2
H3
H4
H5
H6
Low 1Adjustments
Low 2
Low 3
17 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Low 4 [ ]
[ ]Low 5
Low 6
[ ]
[ ][ ]
[ ]Center 1 [ ]
[ ]Center 2 [ ]
[ ]Center 3 [ ]
[ ]
Center 4 [ ]
[ ]
Center 5 [ ]
[ ]
High 1 [ ]
[ ]
High 2 [ ]
[ ]
High 3 [ ]
[ ]
High 4 [ ]
[ ]
High 5 [ ]
[ ]
High 6 [ ]
[ ]
(No.RA053<Rev.001>)1-93
4.22 Adjustment points
TX-RX UNIT (XC1-180)Component Side
4.23 Test Equipment Required for Alignment
* The test equipment which is not used for adjustment is contained in this table.
RTC (CN412)
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.001ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 10W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 10V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 5A
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 8ohm Dummy Load Approx. 8ohm, 3W
13. Regulated Power Supply 5V to 10V, approx. 3A, Useful if ammeter equipped
1-94 (No.RA053<Rev.001>)
Antenna connector adapterThe antenna connector of this transceiver uses an SMAterminal.Use an antenna connector adapter [SMA(f) - BNC(f) or SMA(f)- N(f)] for adjustment. (The adapter is not provided as anoption, so buy a commercially-available one.)
Nut wrenchIn order to turn the volume nut and the channel selector nut,use a recommendation tool.KENWOOD part No.: W05-1123-00
Battery Jig (W05-0909-00)Connect the power cable properly between the battery jiginstalled in the transceiver and the power supply, and be sureoutput voltage and the power supply polarity prior to switchingthe power supply ON, otherwise over voltage and reverseconnection may damage the transceiver, or the power supplyor both.When using the battery jig in user mode, the transceiverassumes that a lithium-ion battery pack is attached to thetransceiver. In adjustment mode, battery type detection is notperformed.
Note: When using the battery jig, you must measure the voltageat the terminals of the battery jig. Otherwise, a slightvoltage drop may occur within the power cable, betweenthe power supply and the battery jig, especially while thetransceiver transmits.
4.24 Radio check Section
+ Terminal (Red)
– Terminal (Black)
S
–
+
C1
10
0P
/25
V
C2
47
0P
/25
V
C3
10
0µ
/25
V
R1
1.8
M
+
(Red)+Terminal
–Terminal(Black)
supplyPowerPower
cable
Schematic diagram
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
+/-0.25ppm+/[email protected]
2. High power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 4.0~6.0W2.3A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
(No.RA053<Rev.001>)1-95
4.25 Common Section
3. Low power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 0.7~1.4W1.1A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
Deviation meterOscilloscopeAGAF VM
Panel ANTSP/MIC connector
Adjust AG input to get a standard MOD.
12.5mV±5.8mV
5. Sensitivity check
1)CH-Sig: 1-1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortion meter8ohm Dummy load
Panel ANTSP/MIC connector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:7.5V2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
126 (Reference value)
1-96 (No.RA053<Rev.001>)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]2) Adj item:[L1]→[L2]→[L3]→[L4]→[L5]→[L6]→[C1]→[C2]→[C3 RxOL:L]→[C4]→[C5]→[H1]→[H2]→[H3]→[H4]→[H5]→[H6]→[C3 RxOL:H (Long press the [] button)]
Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]2) Adj item:[Low1],[Low2], [Low3],[Low4],[Low5], [Low6][Center1], [Center2], [Center3], [Center4], [Center5], [High1],[High2][High3],[High4],[High5][High6][Overlap]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.001ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±30 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-97
4.26 Transmitter Section
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]
Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN412)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. High transmit power (Battery voltage : 7.5V)
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5.0W ±0.1W 2.3A or less
2. Medium transmit power (Battery voltage : 7.5V)
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
4.0W ±0.1W 2.3A or less
3. Low transmit power (Battery voltage : 7.5V)
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
1.0W ±0.1W 1.1A or less
1-98 (No.RA053<Rev.001>)
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX Starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
[Manual Adjustment]1) Set the adjustment
value to “1”.2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed “31”.
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.
[Panel tuning mode]PTT:ONWhile PTT:ON, press the [ ] button to change the 20Hz/2kHz.
[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-99
6. Maximum Deviation
[Analog Wide]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “490” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “490” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-100 (No.RA053<Rev.001>)
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point.Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz. Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-101
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
9. QT Deviation
[Analog Wide]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.540 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-102 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.540 (Reference value)
0.35kHz±0.05kHz
10. DQT Deviation
[Analog Wide]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.440 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-103
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.440 (Reference value)
0.35kHz±0.05kHz
11. LTR Deviation
[Analog Wide]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.530 (Reference value)
1.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-104 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.530 (Reference value)
0.75kHz±0.05kHz
12. DTMF Deviation
[Analog Wide]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.545 (Reference value)
2.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-105
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.545 (Reference value)
1.25kHz±0.05kHz
13. Single Tone Deviation
[Analog Wide]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.520 (Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-106 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.520 (Reference value)
1.50kHz±0.05kHz
14. MSK Deviation
[Analog Wide]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.510 (Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-107
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.510 (Reference value)
1.50kHz±0.05kHz
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.500 (Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-108 (No.RA053<Rev.001>)
16. Battery Warning writing
1) Adj item:[BATT]Adjust:[****]BATT terminal voltage: 6.2V while transmitting.
1) Adj item: [Battery Warning]BATT terminal voltage: 6.2V while transmitting.
Power meterDVM
Panel ANTBATT terminal
[Panel tuning mode]PTT: ONPress [ ] button to store the adjustment value.
[PC test mode]1) Press [Transmit]
button.2) Press [Acquire
Monitored Value] button.
3) Press [Apply] button to store the adjustment value.Confirm that one predetermined numeric in the range 1 to 256 appears.
17. Battery Warning check
[Panel test mode]1) CH-Sig: 1-1
BATT terminal voltage: 6.0V while transmitting.
[Panel test mode]1) Test Channel
Channel: 1Test SignalingType: AnalogSignaling: 1BATT terminal voltage: 6.0V while transmitting.
Check The transceiver can transmit with causing the LED to blink.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-109
4.26.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide)", this signaling is composed of three elements [Balance, Maximum Deviation(Analog Wide) and QT Deviation (Analog Wide)]. Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QTDeviation (Analog Wide).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 5) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide/Narrow) is common with all the analog signaling deviations and CWID Deviation (NXDN VeryNarrow).If Balance and Maximum Deviation (Analog Wide /Narrow) (Transmitter Section 6) have already adjusted, please skip Step2 andadjust from Step3.
Mode Signaling Necessary adjustment and order
Wide Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. QT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation [Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DQT Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. LTR Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation [Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. DTMF Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation [Analog Narrow]
-
2TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide]3. Single Tone Deviation [Analog
Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide]3. MSK Deviation [Analog Wide]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - 1. Balance adjust2. NXDN High Deviation [NXDN
Narrow]
1. Balance adjust2. NXDN High Deviation [NXDN
Very Narrow]
CWID - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - 1. Balance adjust2. DMR High Deviation
-
1-110 (No.RA053<Rev.001>)
4.27 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTSP/MIC connector
Panel Volume knob
Turn the Volume knob to obtain 0.63V AF output.
0.63V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[Panel tuning mode]After input signal from SSG, Increase or decrease the adjustment value so that the RSSI indicator level becomes minimum.[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
(No.RA053<Rev.001>)1-111
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-112 (No.RA053<Rev.001>)
4. Squelch Open
[Analog Wide]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-113
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
5. Squelch Tight
[Analog Wide]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-114 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
7. High RSSI
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-115
4.28 NX-3320(E, E2, E3) TYPE Controls
4.28.1 Preparations for checking/tuning the transceiverBefore attempting to check/tune the transceiver, connect the unitto a suitable power supply.Whenever the transmitter is turned on, the unit must beconnected to a suitable dummy load (i.e. power meter).The speaker output connector must be terminated with an 8ohmdummy load and connected to an AC voltmeter and an audiodistortion meter or a SINAD measurement meter at all timesduring checking/tuning.
4.29 Panel Test Mode (E and E2 types only)
4.29.1 Test mode operation featuresThis transceiver has a test mode. To enter test mode, press andhold the [ ] button while turning the transceiver power ON orpress the [ ] button and select the “Panel Test”. Before thetransceiver enters test mode, the frequency version informationappears on the LCD momentarily. Test mode can be inhibited byprogramming. To exit test mode, turn the transceiver power OFF.The following functions are available in test mode.
• When the panel test mode is activated, the channel selectedwith the 4-way D-pad and the last used signaling number aredisplayed. When it is activated for the first time, the signalingnumber is 1.
4.29.2 Button operation
*1: When the mode is selected as Analog, this function isenabled.
Auxiliary (orange) button
PTT (Push-To-Talk) switch
Side 1 button
Side 2 button
Selector knob Power switch/ Volume control
Transmit/ Receive/ Battery low indicator Light Bar
4-way D-pad
Button "Func" not appears on the sub LCD display
Function Display
[Selector] - -
[] Push: Test channel upHold: Test channel up continuously
Channel No.
[] Push: Test channel downHold: Test channel down continuously
Channel No.
[] Push: Squelch level up *1Hold: Squelch off
Squelch levelSquelch off: icon appears
[] Wide 5k/Wide 4k/Narrow/Very Narrow
Wide 5k: "w"Wide 4k: "s"Narrow: "n"Very Narrow: "v"
[Side1] - -
[Side2] - -
[ ] Shift to panel tuning mode
-
[ ] Function on "Func" appears on the sub LCD display
[ ] - -
[ ] Push: Test signaling upHold: Test signaling up continuously
Signaling No.
[AUX(Orange)]
MSK 1200bps and 2400bps *1
2400bps: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
- -
1-116 (No.RA053<Rev.001>)
• LED indicatorRed LED Lights during transmission.Green LED Lights when there is carrier.
• Sub LCD indicator"Func" Appears at function on.
• LCD display in panel test mode
4.29.3 Frequency and SignalingThe transceiver has been adjusted for the frequencies shown inthe following table. When required, readjust them following theadjustment procedure to obtain the frequencies you want inactual operation.
(1) Test frequency
(2) Signaling
Analog Type Signaling
Button "Func" appears on the sub LCD display
Function Display
[Selector] - -
[] Function off -
[] Analog/NXDN/DMR Analog: "A"NXDN: "N"DMR: "D"
[] Function off -
[] Button/LCD check The position of the selector knob, etc., appear.
[Side1] Function off -
[Side2] Function off -
[ ] High power/Medium power/Low power
High:[ ] icon appearsMedium:[ ] icon appearsLow:[ ] icon appears
[ ] Function off -
[ ] Function off -
[ ] Function off -
[AUX(Orange)]
Compander On/Off On: [ ] icon appears
[PTT] Transmit -
[0] to [9]and[#], [ ]
Function off -
Button "Func" appears on the sub LCD display
Function Display
(Power ON)
Type Frequency range400~520MHz
Temperature [oC] Power
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
Squelch level(Analog mode only)
Sub LCD display
Main LCD display SignalingNo.
Channel No.
Battery type detect"ALKALI": Alkaline battery pack
"LI ": Li-ion"NIMH": Ni-MH"SP": Other
Ex type aredisplayed as "E".
(After 2sec.)
CH E,E2,E3
RX (MHz) TX (MHz)
1 460.05000 460.10000
2 400.05000 400.10000
3 519.95000 519.90000
4 460.00000 460.00000
5 460.20000 460.20000
6 460.40000 460.40000
7~16 - -
No. RX TX
1 None None
2 None Square Wave
3 LTR Data LTR Data
4 QT:67.0Hz QT:67.0Hz
5 QT:151.4Hz QT:151.4Hz
6 QT:210.7Hz QT:210.7Hz
7 QT:254.1Hz QT:254.1Hz
8 DQT:D023N DQT:D023N
9 DQT:D754I DQT:D754I
10 DTMF Decode (CODE: 159D)
DTMF Encode (CODE: 159D)
11 None DTMF Encode (CODE: 9)
12 2-tone Decode (A: 304.7Hz, B: 3106.0Hz)
2-tone Encode (A: 304.7Hz,B: 3106.0Hz)
(No.RA053<Rev.001>)1-117
NXDN Type Signaling
RAN: Radio Access NumberPN9: Pseudo-Random PatternNo.7, 9 Item: PC test mode only
DMR Type Signaling
4.30 Panel Tuning Mode (E and E2 types only)4.30.1 Transceiver tuning (To enter tuning mode)To enter tuning mode, press the [ ] button while the transceiveris in test mode. Use the [ ] button to write tuning data throughtuning modes, and the [ ]/[ ] button to adjust tuningrequirements (1 to 4096 appears on the LCD).Use the [ ] button to select the adjustment item through tuningmodes. Use the [ ] button to adjust 5, 9 or 17 reference leveladjustments, and use the [ ] button to switch between Wide/Narrow.
• LCD display in panel tuning mode
4.30.2 Button operation
13 Single Tone Decode (979.9Hz)
Single Tone Encode (979.9Hz)
14 None Single Tone Encode (1000Hz)
15 None MSK PN9
16 MSK Decode MSK Encode
No. RX TX
1 RAN1 RAN1
2 None PN9
3 RAN1 Maximum Deviation Pattern
7 FSW + PN9 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
No. RX TX
1 CC 00 Burst CC 00 Burst
2 PN9 PN9
3 CC 00 Burst Maximum Deviation Pattern
4 CC 00 Burst 1/3 Deviation Pattern
5 CC 00 Burst 0 Continuous Pattern
6 SYNC (Each Slot) +PN9 Burst Pattern
SYNC (Each Slot) + PN9Burst Pattern
7 SYNC (Super Frame) +PN9 Burst Pattern
SYNC (Super Frame) +PN9 Burst Pattern
8 CC 00 Burst 0 Burst Pattern
9 Tone Pattern Tone Test Burst Pattern
10 Silence Pattern Silence Burst Pattern
11 Audio Test Pattern Audio Test Burst Pattern
12 Vocoder Loop None
No. RX TX
Button Function
Push Hold (1 second)
[Selector] -
[ ] Adjustment value up Continuation up
[ ] Adjustment value down Continuation down
[ ] Auto adjustment start Output tone pattern change of balance adjustment (A change is possible only during balance adjustment.)
[ ] Wide 5k/Wide 4k/Narrow/NXDN/DMR
-
[ Side1 ] -
[ Side2 ] -
[ ] Shift to panel test mode -
[ ] To enter 5 or 9 reference level adjustments
-
[ ] Writes the adjustment value
-
[ ] Go to next adjustment item
Back to last adjustment item (At the time of 5, 9 or 17 point adjustment: Adjustment point change)
[AUX(Orange)]
- -
[PTT] Transmit
[0] to [9]and[#],[ ]
-
An AST 256
2.6
CV voltage, AD value, etc
Sub LCD display
L1
Adjustment point
Main LCD display
Adjustment value(1~4096)
Proper value guide(When the frequency adjustment is necessary,
or is displayed.)
Adjustment item
An : Analog narrow modeAw : Analog wide 5k modeAs : Analog wide 4k modeNn : NXDN narrow modeNv : NXDN very narrow modeD : DMR mode
L1L2L3C1C2C3
H1H2H3
1-118 (No.RA053<Rev.001>)
4.30.3 5, 9 or 17 reference level adjustments frequency
High Transmit Power, Medium Transmit Power, LowTransmit Power, IQ Phase, RSSI Reference 1 DSP(Receive), RSSI Reference 2 RF IC (Receive), RSSIReference 3 DSP (Standby), RSSI Reference 4 RF IC(Standby), Squelch Open, Squelch Tight, Low RSSI,High RSSI
Balance, Maximum Deviation , NXDN High Deviation, DMRHigh Deviation, QT Deviation, DQT Deviation, LTRDeviation, DTMF Deviation, Single Tone Deviation, MSKDeviation, CW ID Deviation
VCO Assist
4.30.4 Adjustment item supplement
Tuning point Display E,E2,E3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L5 430.05000 430.10000
3 C3 460.05000 460.10000
4 H2 490.05000 490.10000
5 H6 519.95000 519.90000
Tuning point Display E,E2,E3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L3 415.05000 415.10000
3 L5 430.05000 430.10000
4 C1 445.05000 445.10000
5 C3 460.05000 460.10000
6 C5 475.05000 475.10000
7 H2 490.05000 490.10000
8 H4 505.05000 505.10000
9 H6 519.95000 519.90000
Tuning point Display E,E2,E3
RX (MHz) TX (MHz)
1 L1 400.05000 400.10000
2 L2 407.55000 407.60000
3 L3 415.05000 415.10000
4 L4 422.55000 422.60000
5 L5 430.05000 430.10000
6 L6 437.55000 437.60000
7 C1 445.05000 445.10000
8 C2 452.55000 452.60000
9 C3 460.05000 460.10000
10 C4 467.55000 467.60000
11 C5 475.05000 475.10000
12 H1 482.55000 482.60000
13 H2 490.05000 490.10000
14 H3 497.55000 497.60000
15 H4 505.05000 505.10000
16 H5 512.55000 512.60000
17 H6 519.95000 519.90000
Adjustment Item Description
LCD Contrast The contrast of LCD display can be changed.
VCO Assist The lock voltage of VCO is adjusted.This item must be adjusted before receiver and transmitter adjustment items.
Frequency Frequency is adjusted under receivingcondition with SSG.The SSG needs 0.001ppm accuracy soplease use a standard oscillator if necessary.This item can be adjusted only in PC TestMode so that the adjustment value is notchanged easily.
RTC Correction Real Time Clock is adjusted.This item uses the internal clock.(Any measurement equipment is not required.)
High Transmit Power
High Transmit Power is adjusted.
Mid Transmit Power Medium Transmit Power is adjusted.
Low Transmit Power Low Transmit Power is adjusted.
Ramp Offset Adjust this item to the optimal Ramp voltage.
Balance The transmit modulation frequency response is adjusted.This item is adjusted so that the deviation of 2kHz becomes the same deviation of 20Hz.This item must be adjusted before all adjustment items for deviations are adjusted.
Maximum Deviation(Analog Wide 5K/Wide 4K/Narrow)
Maximum Deviation of Analog (Wide 5K/Wide 4K/Narrow) is adjusted.This item must be adjusted before all adjustment items for tone deviations are adjusted.
High Deviation NXDN/DMR high deviation is adjusted.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Deviation
The deviation of Single Tone used in “2-tone” and “5-tone” is adjusted.
MSK Deviation MSK deviation is adjusted.
CW ID Deviation CWID tone deviation is adjusted.CWID is used to inform the others who istransmitting on a 6.25-kHz spacing channel.(In FCC rule, Analog mode or CWID isrequired for each channel-spacing.)
Battery Warning Battery Warning Level (LED blinking level) is adjusted.Battery Warning Level minus 0.4V is thetransmission inhibited level.
(No.RA053<Rev.001>)1-119
4.30.5 Adjustment item and Display
IQ Phase Correction of phase difference shift between I and Q.
RSSI Reference The minimum RSSI level for scan stop isadjusted.
Squelch Open The squelch level at level “1” is adjusted.
Squelch Tight The squelch level at level “9” is adjusted.
Low RSSI RSSI display level “ ” is adjusted.Both “Low RSSI” and “High RSSI” must be adjusted. (The curve data of RSSI level is applied.)
High RSSI
Adjustment Item Description
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
1 LCD Contrast CNTR - 1 point ADJ CommonSection 21~256
2 VCO Assist AST (CV voltage) - - 17 - - - CommonSection 31~4096
3 RTC Correction RTC - - CommonSection 5-2.00 ~ -0.01 ,0.00 ,+0.01 ~ +2.00
4 High Transmit Power
H_PWR - - - 5 - - - TransmitterSection 21~1024
5 Medium Transmit Power
M_PWR - - - 5 - - - TransmitterSection 31~1024
6 Low Transmit Power
L_PWR - - - 5 - - - TransmitterSection 41~1024
7 Ramp Offset RAMP (ADC measurement value)
1 point ADJ TransmitterSection 11~1024
8 Balance BAL (Encode frequency) - - 9 - - - TransmitterSection 51~1024
9 Maximum Deviation
ADEV - 9 9 9 - - - TransmitterSection 61~1024
10 NXDN High Deviation
NDEV - - - - 9 9 - TransmitterSection 71~1024
11 DMR High Deviation
DDEV - - - - - - 9 TransmitterSection 81~1024
12 QT Deviation QT - 9 9 9 - - - TransmitterSection 91~1024
13 DQT Deviation DQT - 9 9 9 - - - TransmitterSection 101~1024
14 LTR Deviation LTR - 9 9 9 - - - TransmitterSection 111~1024
15 DTMF Deviation DTMF - 9 9 9 - - - TransmitterSection 121~1024
16 Single Tone Deviation
TONE - 9 9 9 - - - TransmitterSection 131~1024
1-120 (No.RA053<Rev.001>)
17 MSK Deviation MSK - 9 9 9 - - - TransmitterSection 141~1024
18 CW ID Deviation CWID - - - 9 - - - TransmitterSection 151~1024
19 Battery Warning BATT (BATT measurement value)
1 point ADJ TransmitterSection 161~256
20 IQ Phase IQ (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 21~63
21 RSSI Reference 1 DSP (Receive)
RSSI1 (RSSI DSP(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
22 RSSI Reference 2 RF IC(Receive)
RSSI2 (RSSI RF IC(Receive) measurement value)
- - 5 - - - ReceiveSection 31~256
23 RSSI Reference 3 DSP (Standby)
RSSI3 (RSSI DSP (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
24 RSSI Reference 4 RF IC (Standby)
RSSI4 (RSSI RF IC (Standby) measurement value)
- - 5 - - - ReceiveSection 31~256
25 Squelch Open SQL (ASQDET measurement value)
5 5 5 5 5 5 ReceiveSection 41~256
26 Squelch Tight SQLT (ASQDET measurement value)
5 5 5 - - - ReceiveSection 51~256
27 Low RSSI LRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 61~256
28 High RSSI HRSSI (RSSI DSP (Receive) measurement value)
- - 5 - - - ReceiveSection 71~256
Order Adjusutmentitem
Main LCD
display
Sub LCD display
AW (Analog Wide 5k)
AS(Analog Wide 4k)
AN (Analog Narrow)
Nn (NXDN
Narrow)
Nv (NXDN Very
Narrow)
D (DMR)
Adjust item
Number
Adjustment range
(No.RA053<Rev.001>)1-121
4.30.6 Panel tuning mode flow chart
Note:* In this Panel tuning mode flow chart, the Adjustment item name is modified.
Panel Test Mode
[ ]hold LCD Contrast
CNTR
level ecnerefer 9VCO Assist stnemtsujdAAST
RTC CorrectionRTC
Ramp OffsetRAMP
High Power Narrow 5 reference levelH_PWR An Adjustments
Medium Power Narrow 5 reference levelM_PWR An Adjustments
Low Power Narrow 5 reference levelL_PWR An Adjustments
Balance Narrow 9 reference levelBAL An Adjustments
9 reference levelAdjustments
9 reference level
Adjustments
NXDN High Deviation Narrow NXDN High Deviation VeryNarrow
NDEV Nn NDEV Nv
CW ID Deviation NarrowCWID An
BatteryBATT
RSSI (Low) NarrownAISSRL
RSSI (High) NarrownAISSRH
Adjustment Item N/W/VNLCD DisplayFor all adjustment items, press the [ ] buttonto write the adjustment value.
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ] [ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]
9 reference levelAdjustments
[ ]
RSSI Referance 1RSSI1
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]IQ PhaseIQ
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 2RSSI2
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]RSSI Referance 3RSSI3
[ ]press [ ]hold
5 reference levelAdjustments
NarrowAn
[ ]
5 reference levelAdjustments
[ ]
5 reference levelAdjustments
[ ]
RSSI Referance 4RSSI4
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
DMR High DeviationDDEV
[ ]press [ ]hold
[ ]press [ ]hold
DMRD
9 reference levelAdjustments
Analog Max Deviation Narrow Analog Max Deviation Wide4k Analog Max Deviation Wide5kADEV An ADEV As ADEV Aw
[ ]
[ ] [ ] [ ]
[ ] [ ]
[ ]press [ ]hold
Single Tone Deviation Narrow Single Tone Deviation Wide4kTONE An TONE Aw
[ ] [ ][ ]press [ ]hold
[ ]
MSK Deviation Narrow MSK Deviation Wide4k MSK Deviation Wide5k
MSK An MSK As MSK Aw9 reference levelAdjustments
[ ]
[ ]
QT Deviation Narrow QT Deviation Wide4ksATQnATQ
DQT Deviation Narrow DQT Deviation Wide4kDQT An DQT As
LTR Deviation Narrow LTR Deviation Wide4ksARTLnARTL
DTMF Deviation Narrow DTMF Deviation Wide4kDTMF An DTMF As
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]9 reference level
[ ]
QT Deviation Wide5kQT Aw
9 reference levelAdjustments
[ ]
9 reference levelAdjustments
DQT Deviation Wide5kDQT Aw
9 reference levelAdjustments
LTR Deviation Wide5kLTR Aw
DTMF Deviation Wide5kDTMF Aw
Adjustments
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]press [ ]hold
[ ]
[ ]
[ ]
[ ]
[ ]
9 reference level
[ ]Single Tone Deviation Wide5kTONE Aw
Adjustments[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]press [ ]hold
[ ]
Squelch (Open) Narrow Squelch (Open) Wide4k Squelch (Open) Wide5k Squelch (Open)SQL An SQL As SQL Aw SQL
[ ]
[ ] [ ] [ ] [ ] [ ]
[ ] [ ] [ ] [ ]
[ ]
5 reference levelAdjustments
VeryNarrow
NvNarrow
Nn
Squelch (Open)
DMRD
Squelch (Open)[ ]press [ ]hold
[ ]Squelch (Tight) Narrow Squelch (Tight) Wide4k Squelch (Tight) Wide5kwATLQSsATLQSnATLQS
5 reference levelAdjustments
[ ] [ ] [ ]
[ ] [ ]
IQ PhaseRSSI Reference 1RSSI Reference 2RSSI Reference 3RSSI Reference 4Open Squelch
Low RSSIHigh RSSI
Tight Squelch
VCO Assist
Maximum Deviation NXDN High DeviationDMR High DeviationQT DeviationDQT DeviationLTR DeviationDTMF DeviationSingle Tone DeviationMSK DeviationCW ID Deviation
Balance
Adjustment PointLCD Display
5 reference levelL1
L5
C3
H6
H2
Low 1Adjustments
Low 5
Center 3
High 6
5 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]High 2 [ ]
[ ]
[ ]
High Transmit PowerMedium Transmit PowerLow Transmit Power
Adjustment PointLCD Display
9 reference levelL1
L3
L5
H6
C1
C3
C5
H2
H4
Low 1Adjustments
Low 3
Low 5
High 6
9 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Center 1 [ ]
[ ]Center 3
Center 5
[ ]
[ ][ ]
[ ]High 2 [ ]
[ ]High 4 [ ]
[ ]
[ ]
Adjustment PointLCD Display
17 reference levelL1
L2
L3
L4
L5
L6
C1
C2
C3
C4
C5
H1
H2
H3
H4
H5
H6
Low 1Adjustments
Low 2
Low 3
17 reference levelAdjustments exit
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]Low 4 [ ]
[ ]Low 5
Low 6
[ ]
[ ][ ]
[ ]Center 1 [ ]
[ ]Center 2 [ ]
[ ]Center 3 [ ]
[ ]
Center 4 [ ]
[ ]
Center 5 [ ]
[ ]
High 1 [ ]
[ ]
High 2 [ ]
[ ]
High 3 [ ]
[ ]
High 4 [ ]
[ ]
High 5 [ ]
[ ]
High 6 [ ]
[ ]
1-122 (No.RA053<Rev.001>)
4.31 Adjustment points
TX-RX UNIT (XC1-180)Component Side
4.32 Test Equipment Required for Alignment
* The test equipment which is not used for adjustment is contained in this table.
RTC (CN412)
Test Equipment Major Specifications
1. Standard Signal Generator (SSG)
Frequency RangeModulation Output
100 to 900MHzFrequency modulation and external modulation-127dBm/0.1uV to greater than -20dBm/22.4mV
When performing the Frequency adjustment, the following accuracy is necessary.• 0.001ppmUse a standard oscillator for adjustments, if necessary.
2. Power Meter Input ImpedanceOperation FrequencyMeasurement Capability
50ohm100 to 900MHzVicinity of 10W
3. Deviation Meter Frequency Range 100 to 900MHz
4. Digital Volt Meter (DVM)
Measuring RangeInput Impedance
10mV to 10V DCHigh input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. Frequency Counter Frequency RangeFrequency Stability
10Hz to 1000MHz0.2ppm or less
To measure the oscillating frequency of the internal clock 32766.00Hz~32770.00Hz forRTC Correction Resolution 0.01Hz is better for accuracy adjustment.
7. Ammeter 5A
8. AF Volt Meter (AF VM) Frequency RangeVoltage Range
50Hz to 10kHz1mV to 10V
9. Audio Generator (AG) Frequency RangeOutput
50Hz to 5kHz or more0 to 1V
10. Distortion Meter CapabilityInput Level
3% or less at 1kHz50mV to 10Vrms
11. Spectrum Analyzer Measuring Range DC to 1GHz or more
12. 8ohm Dummy Load Approx. 8ohm, 3W
13. Regulated Power Supply 5V to 10V, approx. 3A, Useful if ammeter equipped
(No.RA053<Rev.001>)1-123
Antenna connector adapterThe antenna connector of this transceiver uses an SMAterminal.Use an antenna connector adapter [SMA(f) - BNC(f) or SMA(f)- N(f)] for adjustment. (The adapter is not provided as anoption, so buy a commercially-available one.)
Nut wrenchIn order to turn the volume nut and the channel selector nut,use a recommendation tool.KENWOOD part No.: W05-1123-00
Battery Jig (W05-0909-00)Connect the power cable properly between the battery jiginstalled in the transceiver and the power supply, and be sureoutput voltage and the power supply polarity prior to switchingthe power supply ON, otherwise over voltage and reverseconnection may damage the transceiver, or the power supplyor both.When using the battery jig in user mode, the transceiverassumes that a lithium-ion battery pack is attached to thetransceiver. In adjustment mode, battery type detection is notperformed.
Note: When using the battery jig, you must measure the voltageat the terminals of the battery jig. Otherwise, a slightvoltage drop may occur within the power cable, betweenthe power supply and the battery jig, especially while thetransceiver transmits.
4.33 Radio check Section
+ Terminal (Red)
– Terminal (Black)
S
–
+
C1
10
0P
/25
V
C2
47
0P
/25
V
C3
10
0µ
/25
V
R1
1.8
M
+
(Red)+Terminal
–Terminal(Black)
supplyPowerPower
cable
Schematic diagram
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Frequency check
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
f. counter Panel ANT Check an internal temperature of radio from 20°C to 33°C.
+/-0.25ppm+/[email protected]
2. High power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 4.0~6.0W2.3A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
1-124 (No.RA053<Rev.001>)
3. Low power check (Battery voltage: 7.5V)
1)CH-Sig: 1-1PTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
Power meterAmmeter
Panel ANT Check 0.7~1.4W1.1A or less
2)CH-Sig: 2-1PTT: ON
2)Test ChannelChannel: 2Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
3)CH-Sig: 3-1PTT: ON
3)Test ChannelChannel: 3Test Signaling Type: AnalogSignaling: 1PTT: Press [Transmit] button.
4. MIC sensitivity check
1)CH-Sig: 1-1AG: 1kHzPTT: ON
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1AG: 1kHzPTT: Press [Transmit] button.
Deviation meterOscilloscopeAGAF VM
Panel ANTSP/MIC connector
Adjust AG input to get a standard MOD.
12.5mV±5.8mV
5. Sensitivity check
1)CH-Sig: 1-1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k: -117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)
Narrow: -117dBm (0.32μV)
(MOD: 1kHz/±1.5kHz)
1)Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG outputWide 5k: -117dBm (0.32μV)(MOD: 1kHz/±3kHz)Wide 4k: -117dBm (0.32μV)(MOD: 1kHz/±2.4kHz)Narrow: -117dBm (0.32μV)(MOD: 1kHz/±1.5kHz)
SSGAF VMOscilloscopeDistortion meter8ohm Dummy load
Panel ANTSP/MIC connector
Check 12dB SINAD or more
Item Condition Measurement Adjustment Specifications/RemarksPanel test mode PC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-125
4.34 Common Section
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. Setting
1) DC voltage:7.5V2) SSG standard modulation
[Wide 5k] MOD:1kHz,DEV:3kHz[Wide 4k] MOD:1kHz,DEV:2.4kHz
[Narrow] MOD:1kHz,DEV:1.5kHz
2.LCD Contrast
1) Adj item[CNTR]Adjust:[****]
Press [ ] button to store the adjustment value.
1) Adj item[LCD Contrast]Data: [****]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.
126 (Reference value)
3. VCO Assist
1) Adj item:[AST]Adjust:[****]2) Adj item:[L1]→[L2]→[L3]→[L4]→[L5]→[L6]→[C1]→[C2]→[C3 RxOL:L]→[C4]→[C5]→[H1]→[H2]→[H3]→[H4]→[H5]→[H6]→[C3 RxOL:H (Long press the [] button)]
Adjust:[****]PTT: ONPress [ ] button to store the adjustment value.
1) Adj item: [VCO Assist]2) Adj item:[Low1],[Low2], [Low3],[Low4],[Low5], [Low6][Center1], [Center2], [Center3], [Center4], [Center5], [High1],[High2][High3],[High4],[High5][High6][Overlap]
Press [Apply] button to store the adjustment value.
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.[Manual Adjustment][V] indicator on the PC window shows VCO lock voltage. Change the adjustment value to get VCO lock voltage within the limit of the specified voltage.
Note:Confirm the VCO lock voltage approximately 3 seconds after the adjustment value is changed.
2.5V±0.1V[Automatic Adjustment]After the automatic adjustment is performed, verify that the VCO lock voltage is within the voltage range which is specified by the manual adjustment.[Manual Adjustment]Press [Apply] button to store the adjustment value after all adjustment points have been adjusted.
1-126 (No.RA053<Rev.001>)
4.35 Transmitter Section
4. Frequency
*The Frequency adjustment can be performed only in PC test mode.
1) Adj item: [Frequency]SSG output: -20dBm (22.4mV) (CW (without modulation))
Caution:Perform the frequency adjustment under the following conditions.
• Temperature range of +20°C to +33°C (+68.0°F to +91.4°F).(The temperature is displayed on the Frequency adjustment screen of the KPG-D3/D3N and the LCD of the transceiver.)
• Use an accuracy of 0.001ppm for the SSG. (Use a standard oscillator if necessary.)
SSG Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode]Press [Start] button of “Auto Tuning”. Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
[PC test mode]“IF20” value = Within 0±30 digits. The value of “IF20” will become around “0” after the adjustment has finished.
Remark:“Frequency” is adjusted under receiving condition with SSG.
5. RTC Correciton
1) Adj item:[RTC]Adjust:[****]Press [ ] button to store the adjustment value.
1) Adj item: [RTC Correction]Data: [****]
Press [Apply] button to store the adjustment value.
Frequency Counter
TX-RX
TESTPOINT(CN412)
Remark:The adjustment value should input the display of a Frequency Counter.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. High transmit power (Battery voltage : 7.5V)
1) Adj item:[H_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [High Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
5.0W ±0.1W 2.3A or less
(No.RA053<Rev.001>)1-127
2. Medium transmit power (Battery voltage : 7.5V)
1) Adj item:[M_PWR]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Medium Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
4.0W ±0.1W 2.3A or less
3. Low transmit power (Battery voltage : 7.5V)
1) Adj item:[L_PWR]
Adjust:[****]2) Adj item:
[L1]→[L5]→[C3]→[H2]→[H6]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Low Transmit Power]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
1.0W ±0.1W 1.1A or less
4.Ramp Offset
1)Adj item:[RAMP]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Ramp Offset]Press [Autotune(TX Starts)] button. Press [Apply] button to store the adjustment value.
Power meterAmmeter
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[PC test mode][Automatic Adjustment]1) Press [Autotune(TX
starts)] button.2) Press [Apply] button
to store the adjustment value after the automatic adjustment has finished.
[Manual Adjustment]1) Set the adjustment
value to “1”.2) Press [Transmit]
button and increase the adjustment value slowly while monitoring the offset monitor value.
3) Set the adjustment value when the offset monitor value exceed “31”.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-128 (No.RA053<Rev.001>)
5. Balance
1) Adj item: [An BAL]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Balance]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
The Deviation of 20Hz frequency is fixed.Change the 2kHz adjustment value to become the same deviation of 20Hz within the specified range.
[Panel tuning mode]PTT:ONWhile PTT:ON, press the [] button to change the 20Hz/2kHz.
[PC test mode]PTT: Press [Transmit] button.While PTT:ON, click the check box "2kHz Sine Wave" to change the 20Hz/2kHz.
2kHz Tone deviation is within ± 1.0% of 20Hz tone deviation.
6. Maximum Deviation
[Analog Wide 5k]
1) Adj item: [Aw ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “490” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 4150Hz and 4250Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
4150~4250Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-129
[Analog Wide 4k]
1) Adj item: [As ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “490” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 3310Hz and 3410Hz.Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
3310~3410Hz
[Analog Narrow]
1) Adj item: [An ADEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Maxmum Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “490” for each adjustment point. Transmit at each adjustment point and check that the deviation is between 2050Hz and 2150Hz. Deviation meterLPF: 15kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2050~2150Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-130 (No.RA053<Rev.001>)
7. NXDN High Deviation[NXDN Narrow]
1) Adj item: [Nn NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point.Transmit at each adjustment point and check that the Analog deviation is between 2995Hz and 3117Hz. Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2995~3117Hz
[NXDN Very Narrow]
1) Adj item: [Nv NDEV]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [NXDN High Deviation (NXDN Very Narrow]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 1311Hz and 1363Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
1311~1363Hz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-131
8. DMR High Deviation
1) Adj item: [D DDEV]Adjust: [****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DMR High Deviation (DMR Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write fixed value “500” for each adjustment point. Transmit at each adjustment point and check that the Analog deviation is between 2695Hz and 2803Hz.Deviation meterLPF: 3kHzHPF: OFF
[Panel tuning mode]PTT: ON
[PC test mode]PTT: Press [Transmit] button
2695~2803Hz
9. QT Deviation
[Analog Wide 5k]
1) Adj item: [Aw QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.540 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-132 (No.RA053<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.540 (Reference value)
0.60kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An QT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [QT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.540 (Reference value)
0.35kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-133
10. DQT Deviation
[Analog Wide 5k]
1) Adj item: [Aw DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.440 (Reference value)
0.75kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.440 (Reference value)
0.60kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-134 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An DQT]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DQT Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.440 (Reference value)
0.35kHz±0.05kHz
11. LTR Deviation
[Analog Wide 5k]
1) Adj item: [Aw LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 5k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.530 (Reference value)
1.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-135
[Analog Wide 4k]
1) Adj item: [As LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Wide 4k)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.530 (Reference value)
0.90kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An LTR]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [LTR Deviation (Analog Narrow)]Deviation meterLPF: 3kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.530 (Reference value)
0.75kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-136 (No.RA053<Rev.001>)
12. DTMF Deviation
[Analog Wide 5k]
1) Adj item: [Aw DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.545 (Reference value)
2.50kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.545 (Reference value)
2.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-137
[Analog Narrow]
1) Adj item: [An DTMF]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [DTMF Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.545 (Reference value)
1.25kHz±0.05kHz
13. Single Tone Deviation
[Analog Wide 5k]
1) Adj item: [Aw TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.520 (Reference value)
3.00kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-138 (No.RA053<Rev.001>)
[Analog Wide 4k]
1) Adj item: [As TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.520 (Reference value)
2.40kHz±0.05kHz
[Analog Narrow]
1) Adj item: [An TONE]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [Single Tone Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.520 (Reference value)
1.50kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-139
14. MSK Deviation
[Analog Wide 5k]
1) Adj item: [Aw MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 5k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.510 (Reference value)
3.00kHz±0.05kHz
[Analog Wide 4k]
1) Adj item: [As MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Wide 4k)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.510 (Reference value)
2.40kHz±0.05kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-140 (No.RA053<Rev.001>)
[Analog Narrow]
1) Adj item: [An MSK]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [MSK Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.510 (Reference value)
1.50kHz±0.05kHz
15. CWID Deviation
[Analog Narrow]
1) Adj item: [An CWID]Adjust:[****]
2) Adj item:[L1]→[L3]→[L5]→[C1]→[C3 TxOL:L]→[C5]→[H2]→[H4]→[H6]→[C3 TxOL:H (Long press the [] button)]Adjust:[****]PTT : ONPress [ ] button to store the adjustment value.
1) Adj item: [CWID Deviation (Analog Narrow)]Deviation meterLPF: 15kHzHPF: OFF
2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]→[Overlap]Press [Transmit] button.Press [Apply] button to store the adjustment value.
Deviation meterOscilloscope
Panel ANT Panel [Panel tuning mode] [], [][PC test mode][+], [-]
Write the value as followings.500 (Reference value)
1.10kHz±0.10kHz
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-141
16. Battery Warning writing
1) Adj item:[BATT]Adjust:[****]BATT terminal voltage: 6.2V while transmitting.
1) Adj item: [Battery Warning]BATT terminal voltage: 6.2V while transmitting.
Power meterDVM
Panel ANTBATT terminal
[Panel tuning mode]PTT: ONPress [ ] button to store the adjustment value.
[PC test mode]1) Press [Transmit]
button.2) Press [Acquire
Monitored Value] button.
3) Press [Apply] button to store the adjustment value.Confirm that one predetermined numeric in the range 1 to 256 appears.
17. Battery Warning check
[Panel test mode]1) CH-Sig: 1-1
BATT terminal voltage: 6.0V while transmitting.
[Panel test mode]1) Test Channel
Channel: 1Test SignalingType: AnalogSignaling: 1BATT terminal voltage: 6.0V while transmitting.
Check The transceiver can transmit with causing the LED to blink.
Item Condition Measurement Adjustment Specifications/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-142 (No.RA053<Rev.001>)
4.35.1 Necessary Deviation adjustment item for each signaling and modeThe following shows the necessary adjustment items for each signaling deviation. Please read the following table like the followingexample. In the case of the signaling "QT (Analog Wide 5k)", this signaling is composed of three elements [Balance, MaximumDeviation (Analog Wide 5k) and QT Deviation (Analog Wide 5k)]. Please adjust Balance and Maximum Deviation (Analog Wide 5k)before adjusting QT Deviation (Analog Wide 5k).
• Balance is common with all the above deviation adjustments. If Balance (Transmitter Section 5) has already adjusted, please skipStep1 and adjust from Step2.
• Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) is common with all the analog signaling deviations and CWID Deviation(NXDN Very Narrow).If Balance and Maximum Deviation (Analog Wide 5k/Wide 4k/Narrow) (Transmitter Section 6) have already adjusted, please skipStep2 and adjust from Step3.
Mode Signaling Necessary adjustment and order
Wide 5k Wide 4k Narrow Very Narrow
Analog Audio 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]
-
QT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. QT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. QT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. QT Deviation
[Analog Narrow]
-
DQT 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DQT Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DQT Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DQT Deviation
[Analog Narrow]
-
LTR 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. LTR Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. LTR Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. LTR Deviation
[Analog Narrow]
-
DTMF 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. DTMF Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. DTMF Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. DTMF Deviation
[Analog Narrow]
-
5TONE 1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. Single Tone Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. Single Tone Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. Single Tone Deviation
[Analog Narrow]
-
MSK(Fleetsync)
1. Balance adjust2. Maximum Deviation
[Analog Wide 5k]3. MSK Deviation
[Analog Wide 5k]
1. Balance adjust2. Maximum Deviation
[Analog Wide 4k]3. MSK Deviation
[Analog Wide 4k]
1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. MSK Deviation
[Analog Narrow]
-
NXDN Audio - - 1. Balance adjust2. NXDN High Deviation
[NXDN Narrow]
1. Balance adjust2. NXDN High
Deviation[NXDN Very Narrow]
CWID - - - 1. Balance adjust2. Maximum Deviation
[Analog Narrow]3. CWID Deviation
[Analog Narrow]
DMR Audio - - 1. Balance adjust2. DMR High Deviation
-
(No.RA053<Rev.001>)1-143
4.36 Receiver Section
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1. AF level setting
[Panel test mode]1) CH-Sig: 1-1
SSG output: -47dBm (1mV)(MOD: 1kHz/±1.5kHz)
1) Test ChannelChannel: 1Test Signaling Type: AnalogSignaling: 1SSG output: -47dBm (1mV) (MOD:1kHz/±1.5kHz)
SSGDVMAF VMDummy load
Panel ANTSP/MIC connector
Panel Volume knob
Turn the Volume knob to obtain 0.63V AF output.
0.63V±0.1V
2. IQ Phase
1) Adj item: [An IQ]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
1) Adj item: [IQ Phase]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output:Freq: Tune Freq +8kHzlevel: -53dBm (500μV)(MOD:OFF)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode] [], [][PC test mode][+], [-]
[Panel tuning mode]After input signal from SSG, Increase or decrease the adjustment value so that the RSSI indicator level becomes minimum.[PC test mode][Automatic Adjustment]After input signal from SSG,1) Press [Autotune] button.2) Press [Apply] button to store the adjustment value after the automatic adjustment has finished.
3. RSSI reference [DSP (Receive)]
1) Adj item: [An RSSI 1]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 1 DSP (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
1-144 (No.RA053<Rev.001>)
[RF IC (Receive)]
1) Adj item: [An RSSI 2]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 2 RF IC (Receive)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DSP (Standby)]
1) Adj item: [An RSSI 3]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 3 DSP (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[RF IC (Standby)]
1) Adj item: [An RSSI 4]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [RSSI Reference (Analog Narrow) 4 RF IC (Standby)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, 1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-145
4. Squelch Open
[Analog Wide 5k]
1) Adj item: [Aw SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Open (Analog Wide 5k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Wide 4k]
1) Adj item: [As SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Open (Analog Wide 4k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Open (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level -3dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-146 (No.RA053<Rev.001>)
[NXDN Narrow]
1) Adj item: [Nn SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -5dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[NXDN Very Narrow]
1) Adj item: [Nv SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
1) Adj item: [Squelch Open (NXDN Very Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -2dB(MOD: 400Hz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
[DMR] 1) Adj item: [D SQL]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
1) Adj item: [Squelch Open (DMR)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level at Analog Narrow -4dB(MOD: 400Hz/±1.8kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-147
5. Squelch Tight
[Analog Wide 5k]
1) Adj item: [Aw SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
1) Adj item: [Squelch Tight (Analog Wide 5k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±3kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, press [Apply] button to store the adjustment value.
[Analog Wide 4k]
1) Adj item: [As SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
1) Adj item: [Squelch Tight (Analog Wide 4k)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±2.4kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG, press [Apply] button to store the adjustment value.
[Analog Narrow]
1) Adj item: [An SQLT]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
1) Adj item: [Squelch Tight (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: 12dB SINAD level +6dB (MOD: 1kHz/±1.5kHz)
SSGDistortion meterOscilloscope
Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
6. Low RSSI
1) Adj item: [An LRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [Low RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -118dBm (0.28μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTExt. SP connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
1-148 (No.RA053<Rev.001>)
7. High RSSI adjust
1) Adj item: [An HRSSI]Adjust:[****]
2) Adj item:[L1]→[L5]→[C3]→[H2]→[H6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
1) Adj item: [High RSSI (Analog Narrow)]
2) Adj item:[Low1]→[Low5]→[Center3]→[High2]→[High6]SSG output: -80dBm (22.4μV) (MOD: 1kHz/±1.5kHz)
SSG Panel ANTSP/MIC connector
Panel [Panel tuning mode]After input signal from SSG, press [ ] button to store the adjustment value.
[PC test mode]After input signal from SSG,1) Press [Acquire Monitored Value] button.2) Press [Apply] button to store the adjustment value.
Item Condition Measurement Adjustment Specifications
/RemarksPanel tuning
modePC test mode Test-
equipmentUnit Terminal Unit Parts Method
(No.RA053<Rev.001>)1-149
SECTION 5TROUBLESHOOTING
5.1 Fault Diagnosis of the BGA (Ball Grid Array) IC
OverviewA flowchart for determining whether or not the transceiver can be powered on (the LCD does not function even if the power switch isturned on) due to broken BGA parts.
BGA partsMPU/DSP(C401), mobile DDR(IC402), Flash Memory(IC404)
Checking power supply voltage
Checking voltage
Points to be checked
Points to be checked (1.2V)
Points to be checked
Points to be checked
Normal voltage
Normal voltage
Normal voltage
1.2V
19.2MHz
12M C321.8V 18M C243.2V
1.8V3.2V
32M IC5(1pin)1.8V18M_3 IC12(1pin)
Power supply of each device is connected through the coil.[MPU/DSP]12M: L404, L405, L40618M: L407, L40832M: R452
[mobile DDR]18M: L409
[Flash Memory]32M: R45118M_3: L410
Checking the clock
Checking the clock
Normal voltage 1.2V(peak-to-peak)
19.2MHz MPU/DSP side R410
Pass
Pass
Pass
Pass
Checking the Reset/Control signal
Checking the control signal input to the MPU/DSP
/RST IC403 (4 pin)/BINT Q3 (6 pin)
Checking the control signal output from the MPU/DSPIf the /FRST is always 0V, the MPU/DSP is broken.
The BGA parts are not broken.
Checking for an abnormal point
12M has an abnormal voltage.[MPU/DSP]Remove L404 and L405 and L406 to check the voltage of the 12M..If the voltage becomes normal, the MPU/DSP is broken.
18M has an abnormal voltage.[MPU/DSP]
Remove D402 to check the voltage of Flash Memory side R445.
Fail
Fail
Fail
Fail
/FRST
Checking battery voltage
Points to be checked voltage Normal voltage
6~9V+B CN3
The BGA parts are not broken.If the CN3 is less than 6V, charge the battery.
Fail
Pass
/PSW Q2 (3 pin) 3.2V
Flash memory side D402 1.8V
Remove L407 and L408 to check the voltage of the 18M.If the voltage becomes normal, the MPU/DSP is broken.
[mobile DDR]Remove L409 to check the voltage of the 18M.If the voltage becomes normal, the mobile DDR is broken.
32M has an abnormal voltage.[MPU/DSP]
Remove R452 to check the voltage of the 32M.If the voltage becomes normal, the MPU/DSP is broken.
[Flash memory]Remove R451to check the voltage of the 32M.If the voltage becomes normal, Flash Memory is broken.
If the voltage is not corrected, there is a problem other than the BGA parts.
If the voltage becomes abnormal, Flash Memory is broken.
18M_3 has an abnormal voltage.[Flash memory]Remove L410 to check the voltage of the 18M_3.If the voltage becomes normal, Flash Memory is broken.
1-150 (No.RA053<Rev.001>)
Checking the output signal from the MPU/DSP.
Fail
Fail
Fail
Fail
Fail
Pass
Pass
Pass
Pass
The LCD displays control
It is unlikely that the BGA parts are broken.
Points to be checked Normal voltage/LCD_RSTR479
1.8V
Points to be checked Normal voltage
/CS_F IC405 (4 pin)1.8V 0V 1.8V,
Points to be checked Normal voltage/CS4 CP410 (10 pin) After power-on, and
/CS4 has an abnormal voltage.Check each of the following items. Re-insert the FPC of Display Unit PCB. Replace the Display Unit PCB.
As a result, if the abnormality yet, the MPU/DSP or Flash Memory or mobile DDR may be broken.
Remove R479. If the MPU/DSP side is less than 3.2V,the MPU/DSP or Flash Memory or mobile DDR may be broken.
Points to be checked Normal voltage32M L427 side CN402 3.2V
The BGA parts are not broken.Remove L427 to check the voltage of the 32M.If the voltage becomes normal, re-insert the FPC of Display Unit PCB or replace Display Unit PCB.
The LCD display “INIT ERROR 1”.If an error occurs when the mobile DDR internal RAM reads or writes, The mobile DDR may be broken.
1) /RST : MPU/DSP reset signal LOW Reset2) /BINT : Battery final voltage monitoring LOW Final voltage3) /PSW : Power switch signal LOW ON4) /FRST : Flash memory reset signal LOW Reset5) /CS_F : Flash memory chip select signal LOW Active6) SBC : Switch +B control HIGH ON7) LCD_RST : LCD reset signal LOW Reset8) /CS4 : LCD controller chip select signal LOW Active
After power-on, and
1.8V fixed later
1.8V fixed later
If the IC405 (1pin) is 0V or 1.8V, the MPU/DSP may be broken.
If the IC405 (2pin) is 0V or 1.8V, the MPU/DSP or Flash Memory may be broken.
Pass
Points to be checked Normal voltageSBC MPU/DSP side R13 3.2V
Remove the following parts.C28IC6R29Q4IC14R13
If the MPU/DSP side is 0V,the MPU/DSP or Flash Memory or mobile DDR may be broken.
1.8V 0V 1.8V,
Pass
When an error display appears on the LCD
(No.RA053<Rev.001>)1-151
5.2 Failure diagnosis of the GPS section
Overview:When the GPS function does not operate, use this flowchart to determine the problem.
Major parts for a GPS circuit
• GPS antenna (Connect on CN152, CN153)
• Front End Module (A151)
• SAW Filter (L359)
• Bluetooth/GPS IC (IC351)
• Level conversion IC (IC352, IC353)
• TCXO 19.2MHz (X401)
• 32.768 kHz clock (X351)
• 32BT Regulator (IC8)
• 18BT Regulator (IC7)
• MPU/DSP IC (IC401)
Positioning is not carried out normally.
Are you operating at a location that is suitable for
receiving the GPS signals?Operate at place where is good visibility of the sky.
Verify the contact of the GPS internal antenna with
the PCB.
Re-assembling the GPS antenna correctly
If an antenna is defective, replace the GPS internal antenna.
Fail
Pass
Verify the ANT Matching Parts.
Visually check to C172, L173.
Fail
Replace any abnormal parts.
Check the DISPLAY UNIT PCB.
Fail
Pass
Pass
Pass
Verify the High Pass Filter Parts. Verify
the C175, L176, C177, L178, C179, D180
and D181.
Fail
Replace any abnormal parts.
Replace any abnormal parts.
Verify the FEM.
Verify the L187, C184, C186, R189 and
C190. Check the voltage of the C192 with
the side CN157. And verify PCB side B
parts L194, C193 and R191.
Fail
Check the TX-RX UNIT PCB.
Pass
Pass
Check the DISPLAY UNIT PCB.
MPU/DSP
IC
Levelconversion
IC
LevelConversion
IC
BT/GPS
IC
RF Matching
SAW
FilterATT
Hyper
Pogo
FEM HPFANT
MatchingGPS ANT
CurrentMonitorCircuit
32.768KHzClock
TCXO19.2MHz
PCM
A151
CN354CN356
IC353
IC401 DISPLAYUNIT
TX-RX UNIT
SheetMetal
L359
UARTUART
PCM
IC352 IC351
X401 X351
1-152 (No.RA053<Rev.001>)
Pass
Pass
Pass
Pass
Check the TX-RX UNIT PCB Side A.
Verify the CN354 and
CN356, C391. Fail
Pass
Verify the BT/GPS power
supply.
(32BT) C34[Hot Side]: 3.2V
Pass
Fail
Fail
Fail
Verify the BT/GPS power
supply.
(18BT) R9:
Verify the current monitor
circuit parts.
Check the L354, C377,
R364, R362, R363, C376,
R365 and C378.
Check the PCB side B.
Check the PCB side B.
Fail
Replace abnormal parts.
[The BT/GPS power supply
line 32BT circuit is faulty]
Verify the PCB side A parts.
Replace any abnormal parts.
Still fail
Still fail
[The BT/GPS power supply
line 18BT circuit is faulty]
Verify the PCB side A parts,
C15.
Check the PCB
side B (a).
Check the PCB
side B (b).
Check the PCB
side B.
Still fail
[Current monitor circuit is
faulty.]
Replace any abnormal parts.
Verify the GPS RF circuit
parts.
Check the R369, R356,
R355, R354, L359, C395,
C369 and L353.
[GPS RF circuit is faulty.]
Replace any abnormal parts.
[MPU/DSP (IC401) or IC351
is faulty]
Replace the PCB. Fail
Verify the BT/GPS control
signal (/BT_SHUTDOWN).
R353: 1.8V
(No.RA053<Rev.001>)1-153
R357
R357
Pass
Pass
Pass
Pass
Pass
Verify the reference clock for
the BT/GPS.
(BT_CLK) Intersection of
R360 and R361: Sine
waveform, 19.2MHz, 0.2 to
1.2 Vp-p
Pass
Fail
Fail
[The reference clock circuit
for the BT/GPS is faulty]
Verify the PCB side A parts
C356, R360, R861.
Replace any abnormal parts.
Still fail
Still fail
Check the PCB
side B (c).
[MPU/DSP (IC401) is
faulty] Replace the PCB.
Verify the BT/GPS control
signal (TXD2).
CP352 (2pin):
Square waveform UART data
of 3.2V logic.
[The 18BT_HCI_RX (TXD2)
line circuit is faulty]
Verify the CP352, IC352 and
Replace any abnormal parts.
Verify the BT/GPS control
signal (18BT_RX).
IC352 (7pin):
Square waveform UART data
of 1.8V logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Fail
Verify the BT/GPS control
signal (RXD2).
CP352 (1pin): Square
waveform UART data of 3.2V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Still fail
Verify the BT/GPS control
signal (18BT_TX).
IC352 (8pin):
Square waveform UART data
of 1.8V logic.
[BT/GPS IC (IC351) is
faulty]
Replace the PCB.
[The RXD2 (18BT_TX) line
circuit is faulty]
Verify the CP352, IC352,
Replace any abnormal parts.
Verify the RTC line circuit for the BT/GPS.
X351, L358, C375
Replace any abnormal parts.
FailVerify the RTC for the BT/GPS.
X351 (3 pin): Square waveform, 32.768 kHz,
1.8Vp-p
[The BT/GPS IC is abnormal]
Replace the PCB.
1-154 (No.RA053<Rev.001>)
Descriptions of signal names(1) 32BT: BT/GPS IC 3.2V power supply(2) 18BT: BT/GPS IC 1.8V power supply(3) TXD2: BT/GPS serial data line connected to UART TX of MPU/DSP IC (MPU/DSP to BT/GPS IC)(4) RXD2: BT/GPS serial data line connected to UART RX of MPU/DSP IC (MPU/DSP to BT/GPS IC)(5) 18BT_HCI_RX: BT/GPS serial data line connected to UART RX of BT/GPS IC (MPU to BT/GPS IC)(6) 18BT_HCI_TX: BT/GPS serial data line connected to UART TX of GPS IC (BT/GPS IC to MPU)(7) /BT_SHUTDOWN: BT/GPS active control of MPU/DSP IC (MPU/DSP to BT/GPS IC) High → Active, Low → Reset
Pass
Pass
Pass
Check the PCB side B (a).
Fail
[The BT/GPS power supply line 32BT circuit is
faulty]
Verify the PCB side B parts.
L351, C388, C363, C364, C372
Replace any abnormal parts.
[The BT/GPS IC is
abnormal]
Replace the PCB.
Check the PCB side B (b).
[The BT/GPS power supply line 18BT circuit is
faulty]
Verify the PCB side A parts.
L352, R361, R360, C358, C370, L358, C375,
X351. Replace any abnormal parts.
Fail[The BT/GPS IC is
abnormal]
Replace the PCB.
Check the PCB side B (c).
[The reference clock circuit for the BT/GPS is
faulty]
Verify the PCB side B parts
X401(OUTPUT pin): Clipped sine wave,
X401(VCC pin): 3.2V,
R401, R403, C402, C403, R404, C404, R405,
R406, R410,
Q401(B, E): Clipped sine wave, Q401(C): 3.2V,
R407, C405, C407, R408, C406, L402, C408,
R412, R413, R414, C303, IC303
Replace any abnormal parts.
If any unexchangeable parts are abnormal,
replace the PCB.
Fail [The BT/GPS IC is
abnormal]
Replace the PCB.
(No.RA053<Rev.001>)1-155
5.3 Failure diagnosis of the Bluetooth section
Overview:When the Bluetooth function does not operate, use this flowchart to determine the problem.
DISPLAY
UNIT
TX-RX
UNIT
CN353
Sheet metal
CN155
CN151
IC351IC352
IC353
IC401
L361
X351X401
MPU/DSPIC
BT/GPSIC
TCXO19.2MHz
32.768kHzClock
LC
Filter
Bluetooth
Antenna
Level conversion
IC
Level conversion
IC
UART
PCM PCM
UART
Major parts for a Bluetooth circuit
• Bluetooth antenna (Sheet metal)
• LC filter (L351)
• Bluetooth/GPS IC (IC351)
• Level conversion IC (IC352, IC353)
• TCXO 19.2MHz (X401)
• 32.768 kHz clock (X351)
• 32BT Regulator (IC7)
• 18BT Regulator (IC8)
• MPU/DSP IC (IC401)
I can not pair with the Bluetooth (BT) headset.
Is the BT headset charged enough?
Is the BT headset turned on?
Is the BT headset in pairing mode?
Charge the BT headset. Turn on your BT headset and bring it
within one meter.
Try again pair with BT headset.
the PCB. (CN151, CN155, CN353)
To reassembly correctly the BT antenna.
If an antenna is defective, replace the BT internal antenna.
Verify the BT/GPS power
supply.
(32BT) C34: 3.2V
Fail Fail
No
Verify the antenna matching parts.
Visually check to R359, C353 Fail
Replace any abnormal parts.
Check the PCB
Check the PCB side A.
Check the Display Unit PCB
Fail
Pass
Pass
[The BT/GPS power supply
line 32BT circuit is faulty]
Verify the parts.
IC7, L8, C33, C34, R9
Replace any abnormal parts. Pass
Verify the antenna matching parts.
Visually check to L151, L152, L153, R155, L156,
C158.
Fail Swap to OK PCB and confirm
Replace any abnormal parts.
Check the Display Unit PCB
Pass
Check the PCB side A.
Pass
side B (a).
Verify the contact of the BT internal antenna with
1-156 (No.RA053<Rev.001>)
Pass
Pass
Pass
Pass
Pass
Pass
FailVerify the BT/GPS power
supply.
(18BT) C15: 1.8V
Check the PCB side B.
Check the PCB side B (a).
Fail[The BT/GPS power supply line 32BT circuit is
faulty]
Verify the PCB side B parts.
L351, L366, R367
Replace any abnormal parts.
Fail[The BT/GPS power supply
line 18BT circuit is faulty]
Verify the parts.
IC8, L9, C16, C15, R8
Replace any abnormal parts.
Check the PCB
side B (b).
[The BT/GPS IC is
abnormal]
Replace the PCB.
Fail
Check the PCB side B (b).
[The BT/GPS IC is
abnormal]
Replace the PCB.
[The BT/GPS power supply line 18BT circuit is
faulty]
Verify the PCB side B parts.
L352, L365
Replace any abnormal parts.
Check the PCB side B.
Pass
Fail
Verify the reference clock for
the BT/GPS.
(BT_CLK) Intersection of
C356 and R360: Sine
waveform, 19.2MHz, 0.2 to
1.2 Vp-p
[The reference clock circuit
Verify the BT/GPS control
signal (18BT_HCI_RX).
IC352 (7pin):
Square waveform UART data
of 1.8V logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Pass
Fail
for the BT/GPS is faulty]
Verify the parts
C356, R360, R361, .R413,
R412, C408, L402, C406,
Q401, R407, R405, R406,
C404, R404, X401, R401
Replace any abnormal parts.
Fail
Fail
Verify the BT/GPS control
signal (TXD2).
CP352 (2pin):
Square waveform UART data
of 3.2V logic.
[The 18BT_HCI_RX (TXD2)
line circuit is faulty]
Verify the CP352, IC352
Replace any abnormal parts.
[MPU/DSP (IC401) is
faulty]
Replace the PCB.
[MPU/DSP (IC401) is
faulty]
Replace the PCB.
(No.RA053<Rev.001>)1-157
Descriptions of signal names(1) 32BT: BT/GPS IC 3.2V power supply(2) 18BT: BT/GPS IC 1.8V power supply(3) TXD2: BT/GPS serial data line connected to UART TX of MPU/DSP IC (MPU/DSP to BT/GPS IC)(4) RXD2: BT/GPS serial data line connected to UART RX of MPU/DSP IC (MPU/DSP to BT/GPS IC)(5) 18BT_HCI_RX: BT/GPS serial data line connected to UART RX of BT/GPS IC (MPU to BT/GPS IC)(6) 18BT_HCI_TX: BT/GPS serial data line connected to UART TX of GPS IC (BT/GPS IC to MPU)(7) /BT_SHUTDOWN: BT/GPS active control of MPU/DSP IC (MPU/DSP to BT/GPS IC) High → Active, Low → Reset
Pass
Pass
Pass
Pass
Pass
Verify the BT/GPS control
signal (RXD2).
CP352 (1pin): Square
waveform UART data of 3.2V
logic.
Baud rate:
Default: 115.2kbps
After: 3.967Mbps.
Verify the BT/GPS control
signal (/BT_SHUTDOWN).
R353: 1.8V Fail
Verify the RTC for the BT/GPS.
X351 (3 pin): Square waveform, 32.768 kHz,
1.8Vp-p
[The BT/GPS IC is
abnormal]
Replace the PCB.
Fail
Fail Fail
Fail
Verify the BT/GPS control
signal (18BT_HCI_TX).
IC352 (8pin):
Square waveform UART data
of 1.8V logic.
[The RXD2 (18BT_HCI_TX)
line circuit is faulty]
Verify the CP352, IC352
Replace any abnormal parts.
[The /BT_SHUTDOWN line
circuit is faulty]
Verify the R353, Q351
Replace any abnormal parts.
Verify the RTC line circuit for the BT/GPS.
X351, L358, C375
Replace any abnormal parts.
[MPU/DSP (IC401) is
faulty]
Replace the PCB.
[BT/GPS IC (IC351) is
faulty]
Replace the PCB.
1-158 (No.RA053<Rev.001>)
5.4 Failure diagnosis of the VCO section (NX-3220)
[Overview]The VCO circuit is mounted inside the BLS. BLS stands for "Board Level Shield".This BLS has no lid and provides high shielding performance. Because BLS is difficult to solder, components inside the BLS can't besoldered.When there is a problem with the VCO circuit, the VCO can't be repaired.If the VCO function doesn't work, use this flow chart to identify the problem.The following is explained about failure diagnosis of VCO circuit inside a BLS<E101>.
[About a BLS]BLS is shielding caseBLS for VCO area is integrated type and can not be removed
[Prediction problem related to the VCO circuit]• PLL Unlock
<Radio state>- Unlock beep- VCO Assist voltage tuning is impossible<The cause>- VCO control voltage is abnormal - VCO Assist voltage is abnormal- VCO power supply is abnormal- VCO signal output circuit is abnormal
[VCO circuit inside a BLS<E101>]
VC
O_
MO
D
AS
SIS
T
CV
AS
TS
W
/SA
VE
CP
Z
50C
50
C
R1
22
6.8
k
$D
10
1
$C
10
1
$Q101
$R
10
1
R102
0
C103 33p
C1
02
0.0
1u
D1
11
1S
S4
00
SM
R1
03
22
k
IC102BU7295HFV
1 IN+
2 VSS
3 IN- 4
oUT
5
VDD
C198
2.5p (B)
C1
92
12
p(G
)
L192
27n(H0AM)
C1
91
6p
(B)
C1
07
10
0p
C193
2.5p (B)
C1
94
6p
(B)
L191
27n(H0AM)
C104 100p
C106
0.1u
R1
09
47
R1
13
47
k
C197
470p
CN191
R1
25
0
R1
11
4.7
k
C1
12
4.7
u1
0
2SD2654/W/Q11 3
D1
02
ED
ZV
8.2
B
IC101OPA170AIDRL R
1 IN+
2 V-
3 IN- 4
oUT
5
V+
Q102EM6M2
R106
10
R1
81
22
R11 2
1k
C1
11
47
0p
R1
29
10
k
R1
21
10
k
CN101
R1
04
1k
C105 1u 50
2SC5108FT/Y/Q181
R1
82
8.2
k
R1
83
4.7
k
C1
81
47
0p
R1
84
15
0
L1
81
56
n
LK
73
H0
AM
56
NJ
R1
10
10
0k
C1
82
47
0p
R1
07
10
0k
C183
4p(B)
R108
10ME101
F1B-0095-00
R105 120k
C146
6p
R1
36
10
k
L1
43
47
n
LK
73
H0
AM
47
NJR
13
1
10
0k C
13
9
8p
(B)
2SC5108FT/Y/
Q151
L1
35
27
0n
L4
1-2
78
5-5
3
L1
40
27
0n
L4
1-2
78
5-5
3
L1
32
27
0n
L4
1-2
78
5-5
3
L1
37
27
0n
L4
1-2
78
5-5
3
L139
270nL41-2785-53
C1
40
7p
L1
42
27
0n
L4
1-2
78
5-5
3
C141
9p
C1
37
3pC1
23
0.0
47
u
C1
38
0.7
5p
C1
21
0.1
5u
CK
73
FB
B1
H1
54
K
C144
0.5p
R1
30
15
0
$C
13
1
R126
0
R1
45
18
0
R127
0
C1
45
47
0p
C1
32
47
0p
L136
LB73H0AY-00 4
R128
390 (D)
C1
35
47
0p
L121LB73H0AY-00 4
C134
1000p
R1
33
15
0R
N(D
)
R13410 RN(D)
L1
41
LB
73
H0
AY
-00
4
C133
1000p
R135
0
C1
47
47
0p
C1
42
47
0p
L131
270n
L41-2785-53R132
0$
C1
43
R1
42
15
0
C1
22
10
u2
0C
S7
7A
BE
1D
10
0M
MC
H3
91
4-H
/8/
Q131
D1
36
SM
V11
30
-07
9L
F
D135SMV1801-079LF
D1
33
SM
V1
80
1-0
79
LF
D1
32
D134SMV1801-079LF
D1
31
SM
V1
25
1-0
79
LF
R1
43
5.6
k
R1
20
47
0k
R124
47k
R1
23
47
0k
Q11 4VT6M1
L11 2
LB73H0AY-00 4
Q1
03
VT
6M
1
R141
470k
R140
470k
L138
33n
L41-3378-08
C1
08
0.1
u
R1
37
0
R1
16
0
R139
0
R195
0
R194
33
$R
19
1R
19
3
18
0
ASSIST
CV amp
4.3V
4.1V
3.2V
VCO VCO Buffer
BLS
VCO circuit inside a BLS (in a dotted line)
[A] This point is inside other BLS<E301>
[C]
[D] [E]
[F]
[G] [H]
[ I ]
[B]
(No.RA053<Rev.001>)1-159
[A SIDE]
[B SIDE]
1-160 (No.RA053<Rev.001>)
[Inspection procedure]
[Remarks]The following things are assumed as causes of trouble besides the above• PLL data is abnormal• VCO/PLL lock judgment is abnormal[<IC401>OMAP]
Unlock[Unlock beep / VCO assist tuning is impossible]Assist Auto Tuning
Auto tuning NG
Assist Manual Tuning
Manual tuning NG
Check the VCO output signal
Signal existence
Observe the signal at point [A] with spectrum analyzer thru high impedance probe
No signal
No short-circuit
Remove <C191><C193><L191> and check whether it is short circuited at point [A]
Short-circuit
Check the VCO power supply
Measure the voltage at point [B]
The checked voltage is not about from 4 to 5V.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
The checked voltage is about from 4 to 5V.
Remove <R116> and measure the voltage at point [B]
The checked voltage isabout from 4 to 5V.
The checked voltage is not about from 4 to 5V.
There is a problem outside the BLS. Check the power supply circuit.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Check the VCO Assist voltage supply circuit
Measure the voltage at point [D] by setting Assist tuning value [4096]
This voltage fluctuate in conjunction with the change of Assist tuning value
*When measuring this point, please use a multimeter with sufficiently high input impedance
The checked voltage is about 0V.
The checked voltage is about 0V.
Remove <R108><R109> and measure the voltage at point [E] *Assist voltage switch<Q102> is on in the state of Assist tuning mode
There is a problem outside the BLS. Check the Assist voltage supply circuit.
In case of tuning value is [4096] , this voltage is about 18.3V
*In case of tuning value is [1] , this voltage is about 0V
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Observe the signal at point [A] with spectrum analyzer thru high impedance probe
This signal fluctuate in conjunction with the change of the voltage at point [D]If normal condition, frequency will be less than 272MHz at assist=1And frequency will be more than 348MHz at assist=4096.
This signal doesn't fluctuate in conjunction with the change of the voltage at point [D]
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Check the VCO control voltage supply circuit
Measure the voltage at point [F]
*In case of Assist tuning value is [1] , this voltage is about 4.7VIn case of Assist tuning value is [4096] , this voltage is about 0.1V
This voltage fluctuate in conjunction with the change of Assist tuning value
When the above condition is not satisfied
There is a problem outside the BLS. Check the circuit around IC303.
Remove <IC102> and measure the voltage at point [G]
This voltage difference between point [F] and point [G] is more than 0.1V
This voltage difference between point [F] and point [G] is less than 0.1V
There is a problem outside the BLS. Please check the circuit posterior to <IC102>
Please refer to [Remarks] below.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Modulation trouble / Balance tuning is impossibleCheck the VCO modulation circuit
Check the FM deviation in a Balance tuning mode at 2kHz sample tone
When FM deviation don't fluctuate in conjunction with the change of the Balance tuning value
Check the modulation signal at point [ I ] in a Balance tuning mode at 2kHz sample tone
Signal existence[2kHz tone] *In case of Balance tuning value is [1024], this signal level is about from 1.1[Vp-p] to 1.5[Vp-p]
Remove <R124><R113> and check the modulation signal at point [H] in a Balance tuning mode at 2kHz sample tone
The modulation signal can be confirmed, and signal level fluctuate in conjunction with Balance tuning value
There is a problem with the VCO circuit inside a BLS / Please exchange it for a new PCB
This voltage fluctuate in conjunction with the change of Assist tuning value
Measure the voltage at point [C]
The checked voltage is not about from 3 to 3.2V
The checked voltage is about from 3 to 3.2V.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Remove <R139> and measure the voltage at point [C]
The checked voltage is aboutfrom 3 to 3.2V
The checked voltage is not from 3 to 3.2V.
There is a problem outside the BLS. Check the power supply circuit.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
(No.RA053<Rev.001>)1-161
5.5 Failure diagnosis of the VCO section (NX-3320)
[Overview]The VCO circuit is mounted inside the BLS. BLS stands for "Board Level Shield".This BLS has no lid and provides high shielding performance. Because BLS is difficult to solder, components inside the BLS can't besoldered.When there is a problem with the VCO circuit, the VCO can't be repaired.If the VCO function doesn't work, use this flow chart to identify the problem.The following is explained about failure diagnosis of VCO circuit inside a BLS<E101>.
[About a BLS]BLS is shielding caseBLS for VCO area is integrated type and can not be removed
[Prediction problem related to the VCO circuit]• PLL Unlock
<Radio state>- Unlock beep- VCO Assist voltage tuning is impossible<The cause>- VCO control voltage is abnormal - VCO Assist voltage is abnormal- VCO power supply is abnormal - VCO signal output circuit is abnormal
[VCO circuit inside a BLS<E101>]
AS
TS
W
AS
SIS
T
CV
/SA
VE
CP
CP
Z
/SA
VE
VC
O_
H_
/L
50C
50
C
VC
O_
MO
D
$C
15
5
R1
22
5.6
k
C1
32 4
7p
L1
54
5.1
nL
R7
9Z
0G
J5
N1
G
$D
10
1
R1
54
15
0(D
)
R1
20
47
0k
$C
10
1
R1
51
10
0k
$C
16
8
$Q101
$C
16
9
$R
10
1
R102
0
$C
17
0
C103 33p
R155
4.7
BFU660FQ151
R1
23
47
0k
C1
02
0.0
1u
C1
65
0.1
u
Q114VT6M1
C166
2.5p(B)
D1
11
1S
S4
00
SM
C153
13p(G)
R1
03
22
k
L1
56
15
0n
(-5
3)
IC102BU7295HFV
1 IN+
2 VSS
3 IN- 4
oUT
5
VDD
L111LB73H0AY-0 04
D1
32
BB
55
5-0
2V
H
D1
33
BB
55
5-0
2V
H
C1
07
10
0p
C104 100p
D1
35
BB
55
5-0
2V
H
D134
BB555-02VH
$C180
D1
31
BB
Y5
8-0
2V
$C179
R126
0
R1
30
15
0
C1
13
1u
10
C106
0.1u
C1
35
47
p
$C
17
1
R1
36
0
R1
09
47
R1
56
0
R127
0
$R
11
3
R1
25
0
C1
22
10
u
R1
11
4.7
k
C1
12
4.7
u1
0
C1342p (B)
L1
34
L3
C-0
00
2-0
0
RE1E002SPQ111
2SD2654/W/
Q113
R124
22k
$C
13
7
D1
02
ED
ZV
8.2
B
R1
34
12
0(D
)
IC101OPA 170AIDRLR
1 IN+
2 V-
3 IN- 4
oUT
5
V+
$C
14
6
Q102EM6M2
$C
14
9
$C147R135
8.2
BFU660FQ131
C1
48
0.1
u
C1
23
0.0
47
uC
K7
3F
B1
H4
73
K
R106
10
C145
1p(B)
C1
21
0.1
5u
CK
73
FB
B1
H1
54
K
C133
13p(G)
L1
36
10
0n
(-5
3)
L1
38
10
0n
(-5
3)
L1
37
10
0n
(-5
3)
C1
41
2.5
p(B
)
C1
43
4p
(B)
R1
81
10
0
C1424p(B)
R1
33
5.6
k(D
)
C1
50
47
p
C1
39
47
p
R1
18
47
0k
R112
1k
C1
40
0.3
3u
C1
11
47
p
R1
19
47
0k
R1
29
10
k
C1
44
47
p
L1
33
4.7
nL
R7
9Z
0G
J4
N7
G
Q112VT6M1
R1
21
10
k
R1
32
10
k(D
)
L1
58
15
0n
(-5
3)
L1
57
15
0n
(-5
3)
C1
63
3.5
p(B
)
C1
62
7p
(B)
C1
08
0.1
u
C1619p(B)
CN101
R1
52
5.6
k(D
)
R1
04
1k
C1
67
47
p
C105 1u 50
2SC5108FT/Y/Q181
C1
59
47
p
R1
82
10
k
C1
60
0.3
3u
R1
83
6.8
k
C1
64
47
p
L131
100n(H0AM)
R1
53
10
k(D
)
C136
3p(B)
L1
32
10
0n
(H0
AM
)
C1
81
47
p
C1573p(B)L151
100n(H0AM)
R1
84
22
0
L1
52
10
0n
(H0
AM
)
C1
58
0.5
p
L1
81
10
n
LK
73
H0
AM
10
NJ
R1
10
10
0k
C1
51
4p
(B) C
18
2
47
p
R1
07
10
0k
L1
53
10
0n
(H0
AM
)
R1
31
10
0k
C1
52
47
p
C1
38
0.5
p
C183
3p(B)
D1
55
BB
66
4-0
2V
R1
17
22
D154
BB555-02VH
R108
10M
D1
51
BB
Y5
8-0
2V
E101F1B-0095-00
R1
14
47
k
D1
52
SM
V11
30
-07
9L
F
C1
31
1p
(B)
L1
35
10
0n
(H0
AM
)
L121LB73H0AY-0 04
R105 120k
D1
53
SM
V11
30
-07
9L
F
L112LB73H0AY-0 04 R1
16
22
R128
390(D)
C1
54
47
p
R1
15
0
C1564p (B)
L1
55
L3
C-0
00
1-0
0
R1
37
0
R1
39
0
Q103
VT6M1
R1
40
47
0k
R1
41
47
0k
$L
15
9L
3C
-00
03
-00
$C114
C115 0.5p (B)
C1
09
13
p(G
)
C1
10
5p
(B)
R1
43
27
k
R142
22k
$R
14
4
Q116SSM3K15AMFV
C1
16
3p
C1
17
0.7
5p
Ove
rla
pO
ve
rla
p
BLSASSIST
CV amp
Overlap
4.3V
3.2V
3.9V
VCOH
VCOL
$Q115
VCO circuit inside a BLS (in a dotted line)
[A]
[B]
[C]
[D]
[E]
[F]
[G]
[H] [ I ]
[J]
1-162 (No.RA053<Rev.001>)
[A SIDE]
[B SIDE]
(No.RA053<Rev.001>)1-163
[Inspection procedure]
[Remarks]The following things are assumed as causes of trouble besides the above• PLL data is abnormal• VCO/PLL lock judgment is abnormal[<IC401>OMAP]
or
Unlock[Unlock beep / VCO assist tuning is impossible]Assist Auto Tuning
Auto tuning NG
Assist Manual Tuning
Manual tuning NG
Check the VCO output signal
Signal existence
Observe the signal at point [A] with spectrum analyzer thru high impedance probe
No signal
No short-circuit
Remove <R182><R183><Q181> and check whether it is short circuited at point [A]
Short-circuit
Check the VCO power supply
Measure the voltage at point* [B] or [K]
The checked voltage is not about from 4 to 5V.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
point [B]*In case, Radio frequency is set under 460.05MHz
point [K]In case, other than those above
The checked voltage is about from 4 to 5V.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
point [B]*In case, Radio frequency is set under 460.05MHz
point [K]In case, other than those above Remove <R116> or <R117> and measure the voltage at point [B]* or [K]
The checked voltage isabout from 4 to 5V.
The checked voltage is not about from 4 to 5V.
There is a problem outside the BLS. Check the power supply circuit.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Check the VCO Assist voltage supply circuit
Measure the voltage at point [C] by setting Assist tuning value [4096]
This voltage fluctuate in conjunction with the change of Assist tuning value
*When measuring this point, please use a multimeter with sufficiently high input impedance
The checked voltage is about 0V.
The checked voltage is about 0V.
Remove <R108><R109> and measure the voltage at point [J] *Assist voltage switch<Q102> is on in the state of Assist tuning mode
There is a problem outside the BLS. Check the Assist voltage supply circuit.
In case of tuning value is [4096] , this voltage is about 18.3V
*In case of tuning value is [1] , this voltage is about 0V
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Observe the signal at point [A] with spectrum analyzer thru high impedance probe
Thissignalfluctuatein conjunction with the change of the voltage at point[C]If normal condition, frequency will be less than 800MHz at assist=1And frequency will be more than 1040MHz at assist=4096.
Thissignaldoesn't fluctuatein conjunction with the change of the voltage at point [C]
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Check the VCO control voltage supply circuit
Measure the voltage at point [D]
*In case of Assist tuning value is [1] , this voltage is about 4.7V
In case of Assist tuning value is [4096] , this voltage is about 0.1V
This voltage fluctuate in conjunction with the change of Assist tuning value
When the above condition is not satisfied
There is a problem outside the BLS. Check the circuit around IC303.
Remove <IC102> and measure the voltage at point [E]
Thisvoltage difference between point [D]and point [E]is more than 0.1V
Thisvoltage difference between point [D]and point [E]is less than 0.1V
There is a problem outside the BLS. Please check the circuit posterior to <IC102>
Please refer to [Remarks] below.
There is a problem with the VCO circuit inside a BLS / Please replace to new PCB
Modulation trouble / Balance tuning is impossibleCheck the VCO modulation circuit
Check the FM deviation in a Balance tuning mode at 2kHz sample tone
When FM deviation don't fluctuate in conjunction with the change of the Balance tuning value
Check the modulation signal at point [ I ] in a Balance tuning mode at 2kHz sample tone
Signal existence[2kHz tone] *In case of Balance tuning value is [1024], this signal level is about from 1.1[Vp-p] to 1.5[Vp-p]
(1)Remove <R142><Q116> and check the modulation signal at point [F] in a Balance tuning mode at 2kHz sample tone
(2)Remove <R124> and check the modulation signal at point G in a Balance tuning mode at 2kHz sample tone
The modulation signal can be confirmed, and signal level fluctuate in conjunction with Balance tuning value
There is a problem with the VCO circuit inside a BLS / Please exchange it for a new PCB
(1)*In case, Radio frequency is set under 460.05MHz
(2)In case, other than those above
This voltage fluctuate in conjunction with the change of Assist tuning value
1-164 (No.RA053<Rev.001>)
5.6 Operating Method of Enforced Firmware OverwritingMode
Enforced firmware overwriting mode is a mode to forciblyoverwrite the transceiver firmware when the operations asinstructed in Section 2.2.2 "How to Enter Each Mode" does notallow the transceiver to enter the firmware programming mode,for instance, when the transceiver fails to start up due to thetransceiver failure.
(1) Prepare the followings:• Transceiver (NX-3220 or NX-3320)• Battery (KNB-55L, KNB-56N or KNB-57L)• Programming interface cable (KPG-22U)
(2) Disassemble the transceiver to the condition shown in thefigure.
(3) Connect a transceiver, battery and programming interfacecable (KPG-22U).
(4) While FLDM terminal has a short-circuit with GND terminalon the PCB, turn its power ON.
(5) Upon startup of FLDM loader, "FIRMWARE PROG"appears on an LCD screen.
(6) Start KFL up, select the desired firmware you wish tooverwrite, select the COM port number and baud rate, andthen click the "Write" button.
Note:Configuring "Auto" for baud rate automatically applythe maximal speed of baud rate allowed for aprogramming cable connected to the selected COMport number.Upon start of overwriting on the transceiver,"LOADING" appears on an LCD screen.
(7) Upon completion of the firmware overwriting, "CHECKSUM xxxx" appears on an LCD screen.
Upper: FLDM terminal Lower: GND terminal
(No.RA053<Rev.001>)1-165
5.7 Replacing TX-RX Unit
TX-RX unit information
Method of confirming “Original TX-RX unit” and “ServiceTX-RX unit”
Supplied Accessories of “Service TX-RX unit”
“Service TX-RX unit” DataThe following data is written on the service unit:
After Changing the PCB(1) After changing the printed circuit board, write the up-to-
date Firmware following the instructions in the “2.2REALIGNMENT - 2.2.6 Firmware Programming Mode”.• Write the Firmware in accordance to the Market. If you
write different Market Firmware, there are timescommunication with the FPU is not possible.
(2) Using the KPG-D3/D3N, select your desired item (ModelName) from the Radio Configuration> ProductInformation menu, then use Read/ Write > WriteConfiguration to the Transceiver to write the FPU data(PC Programming mode). When writing to thetransceiver, a Warning Message, corresponding to theitem selected, appears. Click [OK] to continue writing thedata.
(3) Tools > Test/Tuning, then adjust the various adjustmentdata (PC Test Mode) as described in the "SECTION 4ADJUSTMENT".
(4) Attach the new labels corresponding to the new printedcircuit board. (Refer to the images below for labelplacement.)
(5) If necessary, write the FPU data used by the customerwith the KPG-D3/D3N.
Note:• When using the ESN Validation function of NXDN
Trunking, the NXDN ESN number changes when thecircuit board is changed (the number is written on thecircuit board); the NXDN Trunking System cannot beaccessed. Use the KPG-110SM on the NXDN TrunkingSystem side to reprogram the NXDN ESN number.
• When a new printed circuit board is used, the KENWOODESN changes, as does the Transceiver Informationdisplay of the KPG-D3/D3N, but this does not have anyeffect on the operation of the transceiver.
• If changing to the original ESN, please contact our servicecenter.
• KPG-D3N can't be used for E, E2, E3 types.
Model Name Original TX-RX unit Number
For Service TX-RX unit Number
NX-3220(K,K2,K3)
XC1-178K-00 XCA-029K-00
NX-3220(E,E2,E3)
XC1-178K-00 XCA-029E-01
NX-3320 (K,K2,K3)
XC1-180K-00 XCA-030K-00
NX-3320 (E,E2,E3)
XC1-180K-00 XCA-030E-01
Item (Including Parts Number) Quantity
TX-RX Unit (XC1-178, XC1-180) 1
KENWOOD ESN/ NXDN ESN/ ProductNumber/ MPT ESN Label
1
The following marking seals are affixed onthe shield cover of the service TX-RX unit(XCA-029K-00/XCA-029E-01/XCA-030K-00/ XCA-030E-01).
Model Name Marking seal
NX-3220(K,K2,K3)
XCA-029K-00
NX-3220(E,E2,E3)
XCA-029E-01
NX-3320(K,K2,K3)
XCA-030K-00
NX-3320(E,E2,E3)
XCA-030E-01
Data Type Description
KENWOOD ESN Model name: [XC1-178/XC1-180]NX-3220S1 (K, E)Type:K, K2, K3, E, E2, E3The same number as the KENWOODESN label is written.
NXDN ESN/ MPT ESN/Product number
The same number as the NXDN ESN/MPT ESN/ Pruduct Number label iswritten.
1-166 (No.RA053<Rev.001>)
ESN Label Layout
Note:Cut a ESN Label at dotted line.
ESN Label
(No.RA053<Rev.001>) 2-1 2-1 (No.RA053<Rev.001>)
PRECAUTIONS ON SCHEMATIC DIAGRAMS
* Due to the improvement in performance, some part numbers shown in the circuit diagrams
may not agree with those indicated in the Parts List.
* The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for
reference only.
* Since the circuit diagrams are standard ones, the circuits and circuit constants may be
subject to change for improvement without any notice.
* The parts of the symbol with " * " may vary depending on model. Refer to the parts list for details.
* The parts of the symbol with " $ " are unmounted parts.
(No.RA053<Rev.001>) 2-2 2-2 (No.RA053<Rev.001>)
C
B
A
54321
TH201
R684
R6
83
R672
R6
70
R668
R6
65
R6
64
R6
59
R658
R6
57
R6
56
R6
55
R6
54
R6
53
R652
R651
R6
50
R635
R6
17
R6
09
R480
R479
R470
R469
R468 R467
R466
R4
64
R463
R4
62
R4
61
R4
52
R449
R448
R447R446
R4
42
R4
40
R4
39
R4
38
R429
R428
R4
15
R4
11
R3
67
R366
R3
65
R364
R3
63
R3
62
R3
59
R336
R335
R3
33
R3
32
R331
R330
R325
R316
R315R3
14
R313
R3
12
R3
10
R304
R3
03
R302
R301
R269
R2
68
R265
R264
R2
60
R259R258
R2
57 R256
R255
R253 R252
R2
51
R250
R2
49
R248
R2
47
R2
46
R2
45
R244
R237
R2
34
R2
33
R230
R2
27
R2
05 R195
R1
94
R1
93
R192
R141
R140
R139
R1
37
R127
R1
26
R1
25
R124
R1
23
R1
22
R1
21
R1
20
R1
16
R1
13
R112 R66
R6
5
R60
R5
9
R58
R57R56
R52
R5
1R
50
R49 R48
R4
7
R46
R4
5
R4
4 R4
3R
42
R4
1
R40
R39
R3
8
R3
7
R3
6
R3
5
R34R33
R3
2
R3
1
R3
0
R29
R2
8
R2
7
R2
6
R2
5R
24
R23
R22
R2
1
R2
0
R1
9
R18
R17
R1
6
R15
R14 R1
3
R12
R1
1
R1
0
R9
R8
R7
R2
R1
Q654
Q6
53
Q6
52
Q6
51
Q650
Q4
02
Q207Q206
Q205
Q204
Q2
03
Q114
Q113
Q1
03
Q7
Q6
Q5
Q4
Q3
Q2
Q1
L623 L622
L6
12
L6
10
L431
L430
L429
L428L427
L416
L415
L414
L413
L412
L411
L408
L407L406
L405
L4
04
L3
54
L3
15L314
L3
13
L312 L3
11
L310
L3
09
L3
08
L3
07
L3
04
L303
L302
L301 L192
L191
L112
L1
3
L12
L1
1
L10
L9
L8
L7
L6
L5
L4
L3
L1
IC651IC
65
0
IC403
IC303
IC203
IC2
01
IC102
IC15
IC13
IC11
IC10
IC9
IC8
IC1
F650
F2
F1
E301
D655
D621
D6
20
D4
07
D406
D405
D404
D403
D304D303
D204
D1
11
D1
0
D9
D8
D1
CP
41
4C
P4
13
CP
41
2C
P4
11
CP
41
0
CP
40
9C
P4
08
CP
40
5C
P4
04
CP403
CP
40
2
CP303 CP302 CP301
CP
2
CP1
CN
65
2
CN
65
1C
N6
50
CN605
CN604
CN
60
2
CN460
CN
45
8C
N4
57
CN456
CN455
CN453
CN452
CN
45
0
CN443
CN
43
9
CN437
CN436
CN
42
4
CN
42
3
CN
41
2
CN
40
9C
N4
08
CN
40
7C
N4
06
CN
40
5
CN
31
1
CN
31
0C
N3
09
CN
30
8
CN
30
7C
N3
06
CN
30
5
CN
30
4C
N3
03
CN
19
1
CN
10
1
CN
10
CN
8
CN6
CN
5
CN
4
CN
3
C6
93
C692
C691
C6
87
C686C683
C6
81
C679
C6
77
C676
C6
75
C6
74
C673
C6
72
C6
71
C669C667
C6
64
C663
C6
58
C6
57
C604
C5
18
C5
17
C516
C5
15
C5
10
C5
00
C4
99
C4
98
C4
97
C4
96
C4
89
C4
88
C4
87
C477
C476
C475
C474
C473
C472
C471
C470
C469
C454
C4
53
C448
C4
35
C4
34
C433
C4
32
C4
31
C4
30
C4
29
C4
28
C4
27
C4
26
C4
25
C3
92
C3
91
C385
C378
C377
C3
76
C346
C3
45
C343
C3
42
C3
41
C338
C334 C3
33
C3
32
C3
31
C3
30
C3
29
C3
28
C3
27
C326
C325
C324
C323
C3
22
C3
21
C3
20
C319
C317
C316
C315
C314
C313C
31
2
C311
C3
10
C309
C308
C3
06
C3
05
C3
04
C303
C3
02
C301
C2
66
C2
65
C264
C2
63
C2
62
C261
C2
59
C258
C257
C214
C2
13
C2
12
C198
C197
C195
C194
C193
C192
C1
91
C121
C1
12
C111
C1
07
C106
C7
0
C6
9
C6
8
C6
7
C6
6
C65
C64
C6
3
C62
C6
0
C56
C55
C54
C53
C5
2
C51
C5
0
C4
9
C48
C47
C4
6
C44
C4
3
C4
2
C4
1
C40C39
C38
C37
C3
6
C3
5
C34
C3
3
C3
2C3
1
C30
C29
C2
8
C27C26
C2
5
C24
C2
3
C22
C2
1
C20
C1
9
C1
8
C1
7
C1
6
C1
5
C14
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
CN
7
CN
602
F650
R3
R2
R1
CN
2
CN402
IC406
IC13
IC3
IC4
IC1
2
IC5
IC2
IC9
IC10
IC409
CN354
IC7
IC8
IC6
IC651IC18
IC11IC14
IC15
CN
353
CN
1RTC
F1
J651
CN356
CN
357
J7C-0188-00XC1-178
R4
R5
IC17
J6
52
--- Component side view (J7C-0188-00) ---
TX-RX UNIT (XC1-178K-00 (NX-3220))
PRINTED CIRCUIT BOARD
(No.RA053<Rev.001>) 2-3 2-3 (No.RA053<Rev.001>)
C
B
A
5 4 3 2 1
X4
01
X351
TH
40
1
R685 R682
R6
81
R6
80
R678
R6
76
L6
35
R667
R6
63
R661
R6
39
R6
38
R6
37
R636
R6
10
R608
R6
05
R6
04
R6
02
R6
01
L417
R4
51
R450
R4
45
R444
R443
R441
R4
37
R4
36
R4
35
R434
R433 R4
32
R4
31
R430
R427
R426
R425
R424
R423
R422
R421
R420
R4
19
R414R413
R4
12
R410
R4
08
R4
07
R4
06
R4
05
R404
R4
03
R402
R401
R369
R361
R3
60
R3
58 R357
R3
56
R355
R3
54
R353
R3
52
R351
R273
R272
R271
R2
70 R
26
7
R228R223
R2
22
R2
20
R2
19
R2
18
R2
16
R2
15
R2
14
R2
13
R212R211
R2
10
R2
09
R2
08
R207
R2
06
R2
04
R2
02
R2
01
R184
R183
R182
R181
R145
R143
R142
R136
R135
R134
R1
33
R1
32
R131
R130
R129
R128
R111
R110 R109
R1
08
R107
R1
06
R105
R104
R1
03
R1
02
Q6
56
Q4
01
Q351
Q2
02Q201
Q181
Q151
Q1
31
Q102
L6
13
L609
L608
L605
L604
L6
01
L4
10
L4
09
L402
L4
01
L3
66
L365
L361
L359
L358
L353
L3
52
L351
L305
L223
L2
22
L2
21
L2
20
L2
19
L2
18
L2
17
L216L2
15
L214
L2
13
L211
L210
L209
L2
06
L2
03
L201
L181
L143
L142
L1
41
L140
L1
39
L138
L1
37
L1
36
L1
35
L132
L131
L1
21
IC654 IC6
52
IC405
IC404
IC402
IC4
01
IC353
IC352
IC351
IC1
01
E601
E4
01
E3
51
E101
D654
D653
D652
D651
D6
50
D6
09
D4
02
D4
01
D3
02
D3
01
D2
05
D2
03
D2
02
D2
01
D136
D135 D134
D133
D1
32
D1
31
D102
CP601
CP
40
6
CP
40
1
CP
35
2
CP351
CN624
CN
62
3
CN
45
4
CN
44
7C
N4
45
CN
42
2
CN
42
1
CN
41
9
CN
41
8
CN
41
7
CN
41
6
CN
41
5
CN
41
4
CN
41
3
CN
35
5
CN
35
2
CN
35
1
CN203
C6
98
C6
97
C6
95
C690
C689 C688C684
C659
C6
27
C626
C6
25
C6
22
C621
C6
20
C6
18
C6
17
C615
C6
12
C610C609
C608
C6
07
C6
06
C6
03
C602
C601
C502
C5
01
C486
C485
C484
C483
C4
82
C481C480C459C458C457
C4
56
C4
55
C4
52
C4
51
C450
C449
C4
47
C4
46
C4
45
C4
44
C443C442C441C440C439
C438 C437
C436
C424
C4
23
C4
22
C4
21
C408C407
C4
06
C405
C404
C403
C402
C4
01
C3
95
C3
89
C3
88
C387
C3
86
C3
84
C3
83
C3
82
C3
81
C3
80
C379
C375 C374
C3
73
C3
72C371
C3
70
C3
69
C368
C367
C366 C365
C364
C3
63
C361
C360
C359
C358
C3
57
C356
C3
54
C3
44
C3
07
C269
C260
C2
55
C2
53
C252
C2
51
C2
50
C2
49
C248
C2
47
C246
C241
C240
C2
39
C2
38
C2
37
C235
C2
34
C2
33
C2
28
C2
27
C2
26
C225
C224
C2
23
C222
C2
21
C2
20
C2
18
C2
11
C209
C2
07
C206
C2
05
C2
04
C203
C2
02
C183
C182
C181
C147
C146
C145
C144
C142
C1
41
C140
C139
C1
38
C1
37
C1
35
C134 C133
C1
32
C123
C122
C108
C105
C104
C103
C1
02
IC202
IC6
01
IC4
02
IC4
01
IC410
IC4
04
X4
02
CN202 CN201
TX-RX UNIT (XC1-178K-00 (NX-3220))
--- Foil side view (J7C-0188-00) ---
(No.RA053<Rev.001>) 2-4 2-4 (No.RA053<Rev.001>)
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 A- 2BIC2 A- 5CIC3 A- 4CIC4 A- 5CIC5 A- 5CIC6 A- 3CIC7 A- 4AIC8 A- 4AIC9 A- 4BIC10 A- 4BIC11 A- 3CIC12 A- 5CIC13 A- 4CIC14 A- 3BIC15 A- 2BIC17 A- 2BIC18 A- 3CIC101 B- 3CIC102 A- 2BIC201 A- 2BIC202 B- 3BIC203 A- 1AIC303 A- 3AIC351 B- 4AIC352 B- 4BIC353 B- 4BIC401 B- 5BIC402 B- 5AIC403 A- 4AIC404 B- 5CIC405 B- 4CIC406 A- 4BIC409 A- 4BIC410 B- 4CIC601 B- 3CIC650 A- 1BIC651 A- 3CIC652 B- 2CIC654 B- 2C TRANSISTORQ1 A- 3BQ2 A- 2BQ3 A- 2BQ4 A- 3BQ5 A- 5CQ6 A- 3CQ7 A- 3CQ102 B- 3BQ103 A- 3BQ113 A- 3BQ114 A- 3BQ131 B- 3AQ151 B- 3AQ181 B- 3AQ201 B- 2BQ202 B- 2BQ203 A- 2B
Q204 A- 1AQ205 A- 1AQ206 A- 1AQ207 A- 2AQ351 B- 3AQ401 B- 4BQ402 A- 4BQ650 A- 1BQ651 A- 2BQ652 A- 2BQ653 A- 1BQ654 A- 2BQ656 B- 2C DIODE D1 A- 1AD8 A- 3BD9 A- 4BD10 A- 4CD102 B- 3BD111 A- 3BD131 B- 2AD132 B- 2AD133 B- 2AD134 B- 2AD135 B- 2AD136 B- 3AD201 B- 1AD202 B- 2AD203 B- 2AD204 A- 2AD205 B- 1AD301 B- 2AD302 B- 2AD303 A- 2AD304 A- 2AD401 B- 4AD402 B- 4CD403 A- 4BD404 A- 4BD405 A- 4BD406 A- 4CD407 A- 4CD609 B- 3CD620 A- 1CD621 A- 1BD650 B- 1CD651 B- 1CD652 B- 2CD653 B- 1CD654 B- 2CD655 A- 1C RESISTOR R1 A- 5AR2 A- 5AR7 A- 1CR8 A- 4AR9 A- 4A
R10 A- 3BR11 A- 2BR12 A- 3BR13 A- 3BR14 A- 3BR15 A- 3BR16 A- 3BR17 A- 3CR18 A- 2CR19 A- 2BR20 A- 3BR21 A- 2BR22 A- 4CR23 A- 5CR24 A- 5CR25 A- 5CR26 A- 5CR27 A- 3BR28 A- 3BR29 A- 3BR30 A- 1CR31 A- 2BR32 A- 5BR33 A- 5BR34 A- 5BR35 A- 5CR36 A- 5CR37 A- 5CR38 A- 5CR39 A- 4BR40 A- 3CR41 A- 5CR42 A- 5CR43 A- 5CR44 A- 4CR45 A- 4CR46 A- 4CR47 A- 2CR48 A- 2BR49 A- 2BR50 A- 3CR51 A- 3CR52 A- 4CR56 A- 3CR57 A- 3CR58 A- 3CR59 A- 3CR60 A- 3CR65 A- 3BR66 A- 3BR102 B- 3CR103 B- 3CR104 B- 3CR105 B- 3CR106 B- 3CR107 B- 3BR108 B- 3BR109 B- 3BR110 B- 3B
R111 B- 3BR112 A- 2BR113 A- 3AR116 A- 3BR120 A- 3BR121 A- 3BR122 A- 3AR123 A- 3BR124 A- 3AR125 A- 3BR126 A- 3BR127 A- 3BR128 B- 2AR129 B- 2BR130 B- 2AR131 B- 3AR132 B- 2AR133 B- 3AR134 B- 3AR135 B- 3AR136 B- 3AR137 A- 2BR139 A- 3BR140 A- 3BR141 A- 3BR142 B- 3AR143 B- 3AR145 B- 3AR181 B- 3BR182 B- 3AR183 B- 3AR184 B- 3AR192 A- 3BR193 A- 3BR194 A- 3BR195 A- 3BR201 B- 3BR202 B- 3BR204 B- 2AR205 A- 2BR206 B- 3BR207 B- 3BR208 B- 3BR209 B- 3BR210 B- 2BR211 B- 3BR212 B- 3BR213 B- 3BR214 B- 3BR215 B- 3BR216 B- 3BR218 B- 2BR219 B- 2BR220 B- 2AR222 B- 2BR223 B- 3BR227 A- 1AR228 B- 2BR230 A- 2A
R233 A- 1AR234 A- 1AR237 A- 2AR244 A- 2BR245 A- 2BR246 A- 2BR247 A- 2BR248 A- 1BR249 A- 1AR250 A- 1BR251 A- 2AR252 A- 1AR253 A- 1AR255 A- 1AR256 A- 1AR257 A- 1AR258 A- 1AR259 A- 1AR260 A- 1AR264 A- 1AR265 A- 1AR267 B- 2BR268 A- 1AR269 A- 1AR270 B- 3BR271 B- 3BR272 B- 3BR273 B- 3BR301 A- 3BR302 A- 3BR303 A- 2AR304 A- 2AR310 A- 3BR312 A- 2AR313 A- 3BR314 A- 2BR315 A- 2BR316 A- 2BR325 A- 2AR330 A- 3AR331 A- 3AR332 A- 3AR333 A- 3BR335 A- 3AR336 A- 3AR351 B- 3AR352 B- 4BR353 B- 4AR354 B- 4AR355 B- 4AR356 B- 4AR357 B- 3BR358 B- 4BR359 A- 2AR360 B- 4BR361 B- 4BR362 A- 4AR363 A- 4AR364 A- 4A
R365 A- 4AR366 A- 3AR367 A- 3AR369 B- 4AR401 B- 4BR402 B- 4BR403 B- 4CR404 B- 4BR405 B- 4BR406 B- 4BR407 B- 4CR408 B- 4BR410 B- 4BR411 A- 4BR412 B- 4BR413 B- 4BR414 B- 4BR415 A- 4BR419 B- 5CR420 B- 5BR421 B- 5BR422 B- 5BR423 B- 5BR424 B- 5BR425 B- 5BR426 B- 5BR427 B- 5BR428 A- 5BR429 A- 4BR430 B- 4BR431 B- 4AR432 B- 4BR433 B- 4BR434 B- 4BR435 B- 4BR436 B- 4AR437 B- 4BR438 A- 5BR439 A- 5BR440 A- 5BR441 B- 4BR442 A- 4AR443 B- 4CR444 B- 4CR445 B- 4CR446 A- 5BR447 A- 4BR448 A- 4BR449 A- 4BR450 B- 5BR451 B- 5CR452 A- 5BR461 A- 4BR462 A- 4BR463 A- 3AR464 A- 3BR466 A- 4BR467 A- 4BR468 A- 4B
R469 A- 3BR470 A- 3BR479 A- 4CR480 A- 4CR601 B- 3CR602 B- 3CR604 B- 3BR605 B- 3CR608 B- 3CR609 A- 3CR610 B- 3CR617 A- 3BR635 A- 3CR636 B- 3BR637 B- 3CR638 B- 3CR639 B- 3CR650 A- 3CR651 A- 1BR652 A- 3CR653 A- 1BR654 A- 3CR655 A- 2BR656 A- 2CR657 A- 2BR658 A- 1BR659 A- 1BR661 B- 2CR663 B- 1CR664 A- 2CR665 A- 2CR667 B- 1CR668 A- 1CR670 A- 3CR672 A- 1BR676 B- 2CR678 B- 2CR680 B- 1CR681 B- 2CR682 B- 1CR683 A- 1BR684 A- 1BR685 B- 1C CAPACITORC1 A- 1CC2 A- 1AC3 A- 1CC4 A- 2BC5 A- 2BC6 A- 2BC7 A- 2BC8 A- 2BC9 A- 2BC10 A- 2BC14 A- 2BC15 A- 4AC16 A- 4AC17 A- 2B
C18 A- 4CC19 A- 4CC20 A- 4CC21 A- 4CC22 A- 5CC23 A- 5CC24 A- 5CC25 A- 5CC26 A- 5CC27 A- 3CC28 A- 3CC29 A- 3BC30 A- 3BC31 A- 5CC32 A- 5CC33 A- 4AC34 A- 4AC35 A- 5CC36 A- 3BC37 A- 3BC38 A- 4AC39 A- 4BC40 A- 4BC41 A- 4BC42 A- 3CC43 A- 3CC44 A- 5CC46 A- 5CC47 A- 5CC48 A- 4CC49 A- 4CC50 A- 4CC51 A- 3CC52 A- 4CC53 A- 3BC54 A- 2CC55 A- 2BC56 A- 2BC60 A- 2CC62 A- 3CC63 A- 3CC64 A- 3CC65 A- 3CC66 A- 3CC67 A- 2AC68 A- 2AC69 A- 2AC70 A- 2AC102 B- 3CC103 B- 3CC104 B- 3CC105 B- 3CC106 A- 2BC107 A- 2BC108 B- 2AC111 A- 3BC112 A- 3BC121 A- 3BC122 B- 2B
C123 B- 2AC132 B- 2AC133 B- 2AC134 B- 3AC135 B- 2AC137 B- 3AC138 B- 3AC139 B- 3AC140 B- 3AC141 B- 3AC142 B- 3AC144 B- 3AC145 B- 3AC146 B- 3AC147 B- 3AC181 B- 3AC182 B- 3AC183 B- 3BC191 A- 3BC192 A- 3BC193 A- 3BC194 A- 3BC195 A- 3BC197 A- 3BC198 A- 3BC202 B- 1BC203 B- 1BC204 B- 1AC205 B- 1BC206 B- 1BC207 B- 1BC209 B- 2AC211 B- 2AC212 A- 2BC213 A- 2BC214 A- 2BC218 B- 3BC220 B- 3BC221 B- 3BC222 B- 3BC223 B- 3BC224 B- 3BC225 B- 3BC226 B- 1BC227 B- 1BC228 B- 1AC233 B- 3BC234 B- 3BC235 B- 2BC237 B- 2BC238 B- 1BC239 B- 2BC240 B- 2BC241 B- 2BC246 B- 1AC247 B- 1AC248 B- 1AC249 B- 1AC250 B- 1A
C251 B- 1AC252 B- 2BC253 B- 3BC255 B- 1BC257 A- 2BC258 A- 2BC259 A- 2BC260 B- 3BC261 A- 1BC262 A- 2AC263 A- 1AC264 A- 1AC265 A- 1AC266 A- 2AC269 B- 1AC301 A- 2AC302 A- 3BC303 A- 3AC304 A- 2AC305 A- 3BC306 A- 3BC307 B- 2AC308 A- 2AC309 A- 2AC310 A- 2AC311 A- 2BC312 A- 2AC313 A- 2BC314 A- 2BC315 A- 2BC316 A- 3AC317 A- 2AC319 A- 2BC320 A- 2BC321 A- 2AC322 A- 2AC323 A- 3BC324 A- 3BC325 A- 3BC326 A- 3BC327 A- 3AC328 A- 3AC329 A- 3AC330 A- 3AC331 A- 3AC332 A- 3AC333 A- 2AC334 A- 2AC338 A- 2AC341 A- 3AC342 A- 3AC343 A- 3AC344 B- 2AC345 A- 3AC346 A- 3AC354 B- 3AC356 B- 4BC357 B- 4BC358 B- 4B
C359 B- 4BC360 B- 4BC361 B- 4BC363 B- 4BC364 B- 4AC365 B- 4AC366 B- 4AC367 B- 4AC368 B- 4AC369 B- 4AC370 B- 4AC371 B- 4AC372 B- 4AC373 B- 4AC374 B- 4AC375 B- 4AC376 A- 4AC377 A- 4AC378 A- 4AC379 B- 3AC380 B- 3BC381 B- 4BC382 B- 4BC383 B- 4BC384 B- 4BC385 A- 3AC386 B- 4BC387 B- 4BC388 B- 4BC389 B- 4AC391 A- 4AC392 A- 4AC395 B- 4AC401 B- 4CC402 B- 4BC403 B- 4BC404 B- 4BC405 B- 4BC406 B- 4BC407 B- 4BC408 B- 4BC421 B- 4BC422 B- 4BC423 B- 4BC424 B- 4BC425 A- 4BC426 A- 4BC427 A- 4BC428 A- 4BC429 A- 5BC430 A- 5BC431 A- 5BC432 A- 5BC433 A- 5BC434 A- 5BC435 A- 5BC436 B- 5AC437 B- 4AC438 B- 5A
C439 B- 5AC440 B- 5AC441 B- 5AC442 B- 5AC443 B- 4AC444 B- 4AC445 B- 5CC446 B- 5CC447 B- 5CC448 A- 4AC449 B- 4CC450 B- 5BC451 B- 5CC452 B- 4CC453 A- 4BC454 A- 4BC455 B- 4BC456 B- 4AC457 B- 5AC458 B- 5AC459 B- 5AC469 A- 4CC470 A- 4BC471 A- 4BC472 A- 4BC473 A- 4BC474 A- 4BC475 A- 4BC476 A- 4BC477 A- 4BC480 B- 5AC481 B- 4AC482 B- 4AC483 B- 4AC484 B- 4AC485 B- 4AC486 B- 4AC487 A- 5BC488 A- 5BC489 A- 4BC496 A- 4BC497 A- 4BC498 A- 4BC499 A- 4BC500 A- 4AC501 B- 4CC502 B- 4CC510 A- 3CC515 A- 3CC516 A- 3BC517 A- 4CC518 A- 4CC601 B- 3CC602 B- 3CC603 B- 3CC604 A- 2CC606 B- 3BC607 B- 3CC608 B- 3C
C609 B- 3BC610 B- 3BC612 B- 3CC615 B- 3CC617 B- 2BC618 B- 2CC620 B- 3BC621 B- 3CC622 B- 3BC625 B- 2BC626 B- 3CC627 B- 2CC657 A- 1BC658 A- 1CC659 B- 3CC663 A- 3CC664 A- 2CC667 A- 1BC669 A- 1BC671 A- 2BC672 A- 2CC673 A- 2BC674 A- 3CC675 A- 1CC676 A- 2CC677 A- 1BC679 A- 1CC681 A- 1BC683 A- 1BC684 B- 2CC686 A- 1BC687 A- 3CC688 B- 1CC689 B- 2CC690 B- 2CC691 A- 3CC692 A- 3CC693 A- 3CC695 B- 2CC697 B- 2CC698 B- 1C OTHER X351 B- 4AX401 B- 4BX402 B- 4C TH201 A- 2BTH401 B- 4C CN1 A- 2BCN2 A- 4ACN3 A- 1ACN4 A- 2BCN5 A- 4BCN6 A- 3CCN7 A- 2ACN8 A- 3ACN10 A- 3C
CN101 A- 2BCN191 A- 3BCN201 B- 1ACN202 B- 2ACN203 B- 1BCN303 A- 2BCN304 A- 2BCN305 A- 3ACN306 A- 3ACN307 A- 3ACN308 A- 3ACN309 A- 3ACN310 A- 3ACN311 A- 3ACN351 B- 3ACN352 B- 4ACN353 A- 2ACN354 A- 4ACN355 B- 3ACN356 A- 3ACN357 A- 2ACN402 A- 4CCN405 A- 5BCN406 A- 5BCN407 A- 5BCN408 A- 5BCN409 A- 5BCN412 A- 4BCN413 B- 5ACN414 B- 4ACN415 B- 5ACN416 B- 5ACN417 B- 5ACN418 B- 5ACN419 B- 4ACN421 B- 4BCN422 B- 5BCN423 A- 5BCN424 A- 5BCN436 A- 4CCN437 A- 4CCN439 A- 5BCN443 A- 5BCN445 B- 4CCN447 B- 4BCN450 A- 4BCN452 A- 4CCN453 A- 4BCN454 B- 4CCN455 A- 5BCN456 A- 2CCN457 A- 2CCN458 A- 2CCN460 A- 2CCN602 A- 1CCN604 A- 1BCN605 A- 1BCN623 B- 3CCN624 B- 3C
CN650 A- 2CCN651 A- 2CCN652 A- 2C CP1 A- 2ACP2 A- 2BCP301 A- 3ACP302 A- 3ACP303 A- 3ACP351 B- 4BCP352 B- 4BCP401 B- 4ACP402 A- 4BCP403 A- 3ACP404 A- 3BCP405 A- 3BCP406 B- 4CCP408 A- 4BCP409 A- 4BCP410 A- 4CCP411 A- 4CCP412 A- 4CCP413 A- 4BCP414 A- 4BCP601 B- 3C E101 B- 3AE301 A- 3AE351 B- 4BE401 B- 5BE601 B- 3C F1 A- 1BF2 A- 2CF650 A- 1B J651 A- 2CJ652 A- 1C L1 A- 1BL3 A- 4CL4 A- 5CL5 A- 5CL6 A- 5CL7 A- 5CL8 A- 4AL9 A- 4AL10 A- 4AL11 A- 3CL12 A- 4CL13 A- 3CL112 A- 3BL121 B- 2AL131 B- 2AL132 B- 2AL135 B- 2AL136 B- 2AL137 B- 3AL138 B- 3A
L139 B- 3AL140 B- 2AL141 B- 3AL142 B- 3AL143 B- 3AL181 B- 3AL191 A- 3BL192 A- 3BL201 B- 2AL203 B- 2AL206 B- 3BL209 B- 3BL210 B- 1BL211 B- 2BL213 B- 2BL214 B- 2BL215 B- 1AL216 B- 1AL217 B- 1AL218 B- 2BL219 B- 1BL220 B- 1BL221 B- 3BL222 B- 2BL223 B- 2BL301 A- 3BL302 A- 2AL303 A- 3BL304 A- 3BL305 B- 2AL307 A- 2AL308 A- 2AL309 A- 2AL310 A- 2AL311 A- 2BL312 A- 2AL313 A- 2BL314 A- 2BL315 A- 3BL351 B- 3BL352 B- 4BL353 B- 4AL354 A- 4AL358 B- 4AL359 B- 4AL361 B- 4AL365 B- 4BL366 B- 3BL401 B- 4CL402 B- 4BL404 A- 5BL405 A- 4BL406 A- 4BL407 A- 5BL408 A- 5BL409 B- 5AL410 B- 4CL411 A- 5BL412 A- 5B
L413 A- 5BL414 A- 5BL415 A- 5BL416 A- 5BL417 B- 5BL427 A- 4CL428 A- 4CL429 A- 3CL430 A- 3CL431 A- 3BL601 B- 3CL604 B- 2CL605 B- 2CL608 B- 3BL609 B- 3CL610 A- 3CL612 A- 3CL613 B- 3CL622 A- 1BL623 A- 1BL635 B- 2C
(No.RA053<Rev.001>) 2-5 2-5 (No.RA053<Rev.001>)
C
B
A
54321
TH201
R684
R6
83
R672
R6
70
R668
R6
65
R6
64
R6
59
R658
R6
57
R6
56
R6
55
R6
54
R6
53
R652
R651
R6
50
R635
R6
17
R6
09
R480
R479
R470
R469
R468 R467
R466
R4
64
R463
R4
62
R4
61
R4
52
R449
R448
R447R446
R4
42
R4
40
R4
39
R4
38
R429
R428
R4
15
R4
11
R3
67
R366
R3
65
R364
R3
63
R3
62
R3
59
R336
R335
R3
33
R3
32
R331
R330
R325
R316
R315R3
14
R313
R3
12
R3
10
R304R
30
3
R302
R301
R269
R2
68
R265
R264
R2
60
R259R258
R2
57 R256
R255
R253 R252
R2
51
R250
R2
49
R248
R2
47
R2
46
R2
45
R244
R237
R2
34
R2
33
R230
R2
05 R195
R1
94
R184R183
R182
R1
81
R1
43
R1
42
R141
R140
R139
R1
37
R127
R1
26
R1
25
R124
R1
23
R1
22
R1
21
R1
20
R119
R118 R117
R116R115 R114R112 R66
R6
5
R60
R5
9
R58
R57R56
R52
R5
1R
50
R49 R48
R4
7
R46
R4
5
R4
4 R4
3R
42
R4
1
R40
R39
R3
8
R3
7
R3
6
R3
5
R34R33
R3
2
R3
1
R3
0
R29
R2
8
R2
7
R2
6
R2
5R
24
R23
R22
R2
1
R2
0
R1
9
R18 R17
R1
6
R15
R14
R1
3
R12
R1
1
R1
0
R9
R8
R7
R2
R1
Q654
Q6
53
Q6
52
Q6
51
Q650
Q4
02
Q207Q206
Q205
Q204
Q2
03
Q181
Q116
Q114
Q113
Q112
Q1
11 Q1
03
Q7
Q6
Q5
Q4
Q3
Q2
Q1
L623 L622
L6
12
L6
10
L431
L430
L429
L428L427
L416
L415
L414
L413
L412
L411
L408
L407L406
L405
L4
04
L3
54
L3
15L314
L3
13
L312 L3
11
L310
L3
09
L3
08
L3
07
L3
04
L303
L302
L301 L192
L191
L181
L112
L111
L1
3
L12
L1
1
L10
L9
L8
L7
L6
L5
L4
L3
L1
IC651
IC6
50
IC403
IC303
IC203
IC2
01
IC102
IC15
IC1
4
IC13
IC11
IC10
IC3
IC1
F650
F2
F1
E301
D655
D621
D6
20
D4
07
D406
D405
D404
D403
D304D303
D204
D1
11
D1
0
D9
D8
D1
CP
41
4C
P4
13
CP
41
2C
P4
11
CP
41
0
CP
40
9C
P4
08
CP
40
5C
P4
04
CP403
CP
40
2
CP303 CP302 CP301
CP
2
CP1
CN
65
2
CN
65
1C
N6
50
CN605
CN604
CN
60
2
CN460
CN
45
8
CN
45
7
CN456
CN
45
5
CN
45
3
CN452
CN
45
0
CN443
CN
43
9
CN437
CN436
CN
42
4
CN
42
3
CN
41
2
CN
40
9C
N4
08
CN
40
7C
N4
06
CN
40
5
CN
31
1CN
31
0C
N3
09
CN
30
8
CN
30
7C
N3
06CN
30
5
CN
30
4C
N3
03
CN
19
1
CN
10
1
CN
10
CN
8
CN6
CN
5
CN
4
CN
3
C6
93
C692
C691
C6
87
C686C683
C6
81
C679C
67
7
C676
C6
75
C6
74
C673
C6
72
C6
71
C669C667
C666
C6
64
C663
C6
58
C6
57
C604
C5
18
C5
17
C516
C5
15
C5
10
C5
00
C4
99
C4
98
C4
97
C4
96
C4
89
C4
88
C4
87
C477
C476
C475
C474
C473
C472
C471
C470
C469
C454
C4
53
C448
C4
35
C4
34
C433
C4
32
C4
31
C4
30
C4
29
C4
28
C4
27
C4
26
C4
25
C3
92
C3
91
C385
C378
C377
C3
76
C346
C3
45
C343
C3
42
C3
41
C338
C334 C3
33
C332
C331
C3
30
C3
29
C3
28
C3
27
C326
C325
C324
C323
C3
22
C3
21
C3
20
C319
C317
C316
C315
C314
C313
C3
12
C311
C3
10
C309
C308
C3
06
C3
05
C3
04
C303
C3
02
C301
C2
66
C2
65
C264
C2
63
C2
62
C261
C2
59
C258
C257
C214
C2
13
C2
12
C198
C197
C195
C194
C193
C192
C1
91
C1
83
C1
82
C181
C121
C1
17 C116
C1
13
C1
12
C111
C1
07
C106C
70
C6
9
C6
8
C6
7
C6
6
C65
C64
C6
3
C62
C6
0
C56
C55
C54
C5
2
C51
C5
0
C4
9
C48
C47
C4
6
C44
C4
3
C4
2
C4
1
C40C39
C38
C37
C3
6
C3
5
C34
C3
3
C3
2C3
1
C30
C29
C2
8C27C26
C2
5
C24
C2
3
C22
C2
1
C20
C1
9
C1
8
C1
7
C1
6
C1
5
C14
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
CN
7
CN
602
F650
R3
R2
R1
CN
2
CN402
IC406
IC13
IC3
IC4
IC1
2
IC5
IC2
IC9
IC10
IC409
CN354
IC7
IC8
IC6
IC651IC18
IC11
IC14
IC15
CN
35
3C
N1
RTC
F1
J651
CN356
CN
35
7
J7C-0190-00XC1-180
R4
R5
IC17
J6
52
TX-RX UNIT (XC1-180K-00 (NX-3320))
--- Component side view (J7C-0190-00) ---
(No.RA053<Rev.001>) 2-6 2-6 (No.RA053<Rev.001>)
C
B
A
5 4 3 2 1
X4
01
X351
TH
40
1
R685 R682
R6
81
R6
80
R678
R6
76
L6
35
R667
R6
63
R661
R6
39
R6
38
R6
37
R636
R6
10
R608
R6
05
R6
04
R6
02
R6
01
L417
R4
51
R450
R4
45
R444
R443
R441
R4
37
R4
36
R4
35
R434
R433 R4
32
R4
31
R430
R427
R426
R425
R424
R423
R422
R421
R420
R4
19
R414R413
R4
12
R410
R4
08
R4
07
R4
06
R4
05
R404
R4
03
R402
R401
R369
R361
R3
60
R3
58 R357
R3
56
R355
R3
54
R353
R3
52
R351
R2
70
R2
67
R2
66
R228
R2
27
R225
R224R223
R2
22
R221
R2
19
R2
18
R2
16
R2
15
R2
14
R2
13
R212R211
R2
10
R2
09
R2
08
R207
R2
06
R204
R1
56
R155
R154
R153 R152
R151
R136
R135
R1
34
R133
R132
R131
R130
R129
R128
R111
R110 R109
R1
08
R107
R1
06
R105
R104
R1
03
R1
02
Q6
56
Q4
01
Q351
Q2
02Q201
Q1
51
Q1
31
Q102
L6
13
L609
L608
L605
L604
L6
01
L4
10
L4
09
L402
L4
01
L3
66
L365
L361
L359
L358
L353
L3
52
L351
L2
18
L217L2
16
L215
L214
L2
13
L212
L211
L210
L209
L208
L207L2
06
L2
05
L204
L203
L202
L2
01
L158
L1
57
L1
56
L155
L1
54 L1
53
L1
52 L151
L1
38
L1
37
L1
36
L1
35
L134
L1
33
L1
32
L131
L1
21
IC654 IC6
52
IC405
IC404
IC402
IC4
01
IC353
IC352
IC351
IC1
01
E601
E4
01
E3
51
E101
D654
D653
D652
D651
D6
50
D6
09
D4
02
D4
01
D3
02
D3
01
D2
06
D2
03
D2
02
D2
01
D1
55
D154
D153D152
D1
51
D1
35
D134
D1
33
D132
D1
31
D102
CP601
CP
40
6
CP
40
1
CP
35
2
CP351
CN624
CN623
CN
45
4
CN
44
7C
N4
45
CN
42
2
CN
42
1
CN
41
9
CN
41
8
CN
41
7
CN
41
6
CN
41
5
CN
41
4
CN
41
3
CN
35
5
CN
35
2
CN
35
1
CN202
CN201
C6
98
C6
97
C6
95
C690
C689 C688C684
C659
C6
27
C626
C6
25
C6
22
C621
C6
20
C6
18
C6
17
C615
C6
12
C610C609
C608
C6
07
C6
06
C6
03
C602
C601
C502
C5
01
C486
C485
C484
C483
C4
82
C481C480C459C458C457
C4
56
C4
55
C4
52
C4
51
C450
C449
C4
47
C4
46
C4
45
C4
44
C443C442C441C440C439
C438 C437
C436
C424
C4
23
C4
22
C4
21
C408C407
C4
06
C405
C404
C403
C402
C4
01
C3
95
C3
89
C3
88
C387C3
86
C3
84
C3
83
C3
82
C3
81
C3
80
C379
C375C374
C3
73
C3
72C371
C3
70
C3
69
C368
C367
C366 C365
C364
C3
63
C361
C360C359
C358
C3
57
C356
C3
54
C3
44
C270
C2
68
C267
C255
C2
53
C252
C2
51
C250
C2
49
C2
48
C2
47
C2
46
C2
45
C2
44
C243
C241
C240
C2
39
C2
37
C236
C235
C2
34
C2
33
C232
C231C2
30
C2
29
C228
C2
27
C2
26
C225
C224
C2
23
C222
C2
21
C2
20
C2
19
C2
18
C2
17
C2
16
C2
15C211
C2
09
C208
C203
C1
67
C166
C1
65
C164
C1
63
C1
62
C161
C160
C159
C158 C157
C156C154
C153
C1
52
C1
51
C1
50
C1
48
C145
C144
C1
43
C142
C1
41
C140
C139
C138 C136
C135C134
C133 C1
32
C1
31
C123
C122
C115
C1
10
C1
09
C108
C105
C104
C103
C1
02
IC202
IC6
01
IC4
02
IC4
01
IC410
IC4
04
X4
02
TX-RX UNIT (XC1-180K-00 (NX-3320))
--- Foil side view (J7C-0190-00) ---
(No.RA053<Rev.001>) 2-7 2-7 (No.RA053<Rev.001>)
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC1 A- 2BIC2 A- 5CIC3 A- 4CIC4 A- 5CIC5 A- 5CIC6 A- 3CIC7 A- 4AIC8 A- 4AIC9 A- 4BIC10 A- 4BIC11 A- 3CIC12 A- 5CIC13 A- 4CIC14 A- 3BIC15 A- 2BIC17 A- 2BIC18 A- 3CIC101 B- 3CIC102 A- 2BIC201 A- 2BIC202 B- 3BIC203 A- 1AIC303 A- 3AIC351 B- 4AIC352 B- 4BIC353 B- 4BIC401 B- 5BIC402 B- 5AIC403 A- 4AIC404 B- 5CIC405 B- 4CIC406 A- 4BIC409 A- 4BIC410 B- 4CIC601 B- 3CIC650 A- 1BIC651 A- 3CIC652 B- 2CIC654 B- 2C TRANSISTORQ1 A- 3BQ2 A- 2BQ3 A- 2BQ4 A- 3BQ5 A- 5CQ6 A- 3CQ7 A- 3CQ102 B- 3BQ103 A- 3BQ111 A- 3BQ112 A- 3BQ113 A- 3BQ114 A- 3BQ116 A- 3AQ131 B- 3AQ151 B- 3AQ181 A- 3AQ201 B- 2BQ202 B- 2BQ203 A- 2B
Q204 A- 1AQ205 A- 1AQ206 A- 1AQ207 A- 2AQ351 B- 3AQ401 B- 4BQ402 A- 4BQ650 A- 1BQ651 A- 2BQ652 A- 2BQ653 A- 1BQ654 A- 2BQ656 B- 2C DIODE D1 A- 1AD8 A- 3BD9 A- 4BD10 A- 4CD102 B- 3BD111 A- 3BD131 B- 2AD132 B- 2AD133 B- 2AD134 B- 2AD135 B- 3AD151 B- 2AD152 B- 3AD153 B- 2AD154 B- 3AD155 B- 3AD201 B- 1AD202 B- 2AD203 B- 2AD204 A- 2AD206 B- 1AD301 B- 2AD302 B- 2AD303 A- 2AD304 A- 2AD401 B- 4AD402 B- 4CD403 A- 4BD404 A- 4BD405 A- 4BD406 A- 4CD407 A- 4CD609 B- 3CD620 A- 1CD621 A- 1BD650 B- 1CD651 B- 1CD652 B- 2CD653 B- 1CD654 B- 2CD655 A- 1C RESISTOR R1 A- 5AR2 A- 5AR7 A- 1CR8 A- 4A
R9 A- 4AR10 A- 3BR11 A- 2BR12 A- 3BR13 A- 3BR14 A- 3BR15 A- 3BR16 A- 3BR17 A- 3CR18 A- 2CR19 A- 2BR20 A- 3BR21 A- 2BR22 A- 4CR23 A- 5CR24 A- 5CR25 A- 5CR26 A- 5CR27 A- 3BR28 A- 3BR29 A- 3BR30 A- 1CR31 A- 2BR32 A- 5BR33 A- 5BR34 A- 5BR35 A- 5CR36 A- 5CR37 A- 5CR38 A- 5CR39 A- 4BR40 A- 3CR41 A- 5CR42 A- 5CR43 A- 5CR44 A- 4CR45 A- 4CR46 A- 4CR47 A- 2CR48 A- 2BR49 A- 2BR50 A- 3CR51 A- 3CR52 A- 4CR56 A- 3CR57 A- 3CR58 A- 3CR59 A- 3CR60 A- 3CR65 A- 3BR66 A- 3BR102 B- 3CR103 B- 3CR104 B- 3CR105 B- 3CR106 B- 3CR107 B- 3BR108 B- 3BR109 B- 3BR110 B- 3BR111 B- 3BR112 A- 2B
R114 A- 3BR115 A- 3BR116 A- 3BR117 A- 3BR118 A- 3BR119 A- 3BR120 A- 3BR121 A- 3BR122 A- 3AR123 A- 3BR124 A- 3AR125 A- 3BR126 A- 3BR127 A- 3BR128 B- 2AR129 B- 2BR130 B- 2AR131 B- 3AR132 B- 3BR133 B- 3BR134 B- 3BR135 B- 3AR136 B- 3AR137 A- 2BR139 A- 3BR140 A- 3BR141 A- 3BR142 A- 3AR143 A- 3AR151 B- 3AR152 B- 3AR153 B- 3AR154 B- 3AR155 B- 3AR156 B- 3AR181 A- 3BR182 A- 3AR183 A- 3AR184 A- 3AR194 A- 3BR195 A- 3BR204 B- 2AR205 A- 2BR206 B- 3BR207 B- 3BR208 B- 3BR209 B- 3BR210 B- 2BR211 B- 3BR212 B- 3BR213 B- 3BR214 B- 3BR215 B- 3BR216 B- 3BR218 B- 2BR219 B- 2BR221 B- 2BR222 B- 2BR223 B- 3BR224 B- 2BR225 B- 2BR227 B- 1A
R228 B- 2BR230 A- 2AR233 A- 1AR234 A- 1AR237 A- 2AR244 A- 2BR245 A- 2BR246 A- 2BR247 A- 2BR248 A- 1BR249 A- 1AR250 A- 1BR251 A- 2AR252 A- 1AR253 A- 1AR255 A- 1AR256 A- 1AR257 A- 1AR258 A- 1AR259 A- 1AR260 A- 1AR264 A- 1AR265 A- 1AR266 B- 2BR267 B- 2BR268 A- 1AR269 A- 1AR270 B- 1BR301 A- 3BR302 A- 3BR303 A- 2AR304 A- 2AR310 A- 3BR312 A- 2AR313 A- 3BR314 A- 2BR315 A- 2BR316 A- 2BR325 A- 2AR330 A- 3AR331 A- 3AR332 A- 3AR333 A- 3BR335 A- 3AR336 A- 3AR351 B- 3AR352 B- 4BR353 B- 4AR354 B- 4AR355 B- 4AR356 B- 4AR357 B- 3BR358 B- 4BR359 A- 2AR360 B- 4BR361 B- 4BR362 A- 4AR363 A- 4AR364 A- 4AR365 A- 4AR366 A- 3AR367 A- 3A
R369 B- 4AR401 B- 4BR402 B- 4BR403 B- 4CR404 B- 4BR405 B- 4BR406 B- 4BR407 B- 4CR408 B- 4BR410 B- 4BR411 A- 4BR412 B- 4BR413 B- 4BR414 B- 4BR415 A- 4BR419 B- 5CR420 B- 5BR421 B- 5BR422 B- 5BR423 B- 5BR424 B- 5BR425 B- 5BR426 B- 5BR427 B- 5BR428 A- 5BR429 A- 4BR430 B- 4BR431 B- 4AR432 B- 4BR433 B- 4BR434 B- 4BR435 B- 4BR436 B- 4AR437 B- 4BR438 A- 5BR439 A- 5BR440 A- 5BR441 B- 4BR442 A- 4AR443 B- 4CR444 B- 4CR445 B- 4CR446 A- 5BR447 A- 4BR448 A- 4BR449 A- 4BR450 B- 5BR451 B- 5CR452 A- 5BR461 A- 4BR462 A- 4BR463 A- 3AR464 A- 3BR466 A- 4BR467 A- 4BR468 A- 4BR469 A- 3BR470 A- 3BR479 A- 4CR480 A- 4CR601 B- 3CR602 B- 3C
R604 B- 3BR605 B- 3CR608 B- 3CR609 A- 3CR610 B- 3CR617 A- 3BR635 A- 3CR636 B- 3BR637 B- 3CR638 B- 3CR639 B- 3CR650 A- 3CR651 A- 1BR652 A- 3CR653 A- 1BR654 A- 3CR655 A- 2BR656 A- 2CR657 A- 2BR658 A- 1BR659 A- 1BR661 B- 2CR663 B- 1CR664 A- 2CR665 A- 2CR667 B- 1CR668 A- 1CR670 A- 3CR672 A- 1BR676 B- 2CR678 B- 2CR680 B- 1CR681 B- 2CR682 B- 1CR683 A- 1BR684 A- 1BR685 B- 1C CAPACITORC1 A- 1CC2 A- 1AC3 A- 1CC4 A- 2BC5 A- 2BC6 A- 2BC7 A- 2BC8 A- 2BC9 A- 2BC10 A- 2BC14 A- 2BC15 A- 4AC16 A- 4AC17 A- 2BC18 A- 4CC19 A- 4CC20 A- 4CC21 A- 4CC22 A- 5CC23 A- 5CC24 A- 5CC25 A- 5CC26 A- 5C
C27 A- 3CC28 A- 3CC29 A- 3BC30 A- 3BC31 A- 5CC32 A- 5CC33 A- 4AC34 A- 4AC35 A- 5CC36 A- 3BC37 A- 3BC38 A- 4AC39 A- 4BC40 A- 4BC41 A- 4BC42 A- 3CC43 A- 3CC44 A- 5CC46 A- 5CC47 A- 5CC48 A- 4CC49 A- 4CC50 A- 4CC51 A- 3CC52 A- 4CC54 A- 2CC55 A- 2BC56 A- 2BC60 A- 2CC62 A- 3CC63 A- 3CC64 A- 3CC65 A- 3CC66 A- 3CC67 A- 2AC68 A- 2AC69 A- 2AC70 A- 2AC102 B- 3CC103 B- 3CC104 B- 3CC105 B- 3CC106 A- 2BC107 A- 2BC108 B- 2AC109 B- 3AC110 B- 3AC111 A- 3BC112 A- 3BC113 A- 3BC115 B- 3AC116 A- 3BC117 A- 3BC121 A- 3BC122 B- 2BC123 B- 2AC131 B- 2AC132 B- 2AC133 B- 2AC134 B- 3AC135 B- 2AC136 B- 3A
C138 B- 3AC139 B- 3AC140 B- 3AC141 B- 3AC142 B- 3AC143 B- 3AC144 B- 3BC145 B- 3AC148 B- 3BC150 B- 3BC151 B- 2AC152 B- 2AC153 B- 2AC154 B- 2AC156 B- 3AC157 B- 3AC158 B- 3AC159 B- 3AC160 B- 3AC161 B- 3AC162 B- 3AC163 B- 3AC164 B- 3AC165 B- 3AC166 B- 3AC167 B- 3AC181 A- 3AC182 A- 3BC183 A- 3BC191 A- 3BC192 A- 3BC193 A- 3BC194 A- 3BC195 A- 3BC197 A- 3BC198 A- 3BC203 B- 1BC208 B- 2AC209 B- 2AC211 B- 2AC212 A- 2BC213 A- 2BC214 A- 2BC215 B- 1AC216 B- 3BC217 B- 3BC218 B- 3BC219 B- 3BC220 B- 3BC221 B- 3BC222 B- 3BC223 B- 3BC224 B- 3BC225 B- 3BC226 B- 1BC227 B- 1BC228 B- 1AC229 B- 3BC230 B- 3BC231 B- 2BC232 B- 2BC233 B- 3B
C234 B- 3BC235 B- 2BC236 B- 1BC237 B- 2BC239 B- 2BC240 B- 2BC241 B- 2BC243 B- 2BC244 B- 1BC245 B- 1BC246 B- 1AC247 B- 1AC248 B- 1AC249 B- 1AC250 B- 1AC251 B- 1AC252 B- 2AC253 B- 3BC255 B- 1BC257 A- 2BC258 A- 2BC259 A- 2BC261 A- 1BC262 A- 2AC263 A- 1AC264 A- 1AC265 A- 1AC266 A- 2AC267 B- 3BC268 B- 2BC270 B- 2AC301 A- 2AC302 A- 3BC303 A- 3AC304 A- 2AC305 A- 3BC306 A- 3BC308 A- 2AC309 A- 2AC310 A- 2AC311 A- 2BC312 A- 2AC313 A- 2BC314 A- 2BC315 A- 2BC316 A- 3AC317 A- 2AC319 A- 2BC320 A- 2BC321 A- 2AC322 A- 2AC323 A- 3BC324 A- 3BC325 A- 3BC326 A- 3BC327 A- 3AC328 A- 3AC329 A- 3AC330 A- 3AC331 A- 3AC332 A- 3AC333 A- 2A
C334 A- 2AC338 A- 2AC341 A- 3AC342 A- 3AC343 A- 3AC344 B- 2AC345 A- 3AC346 A- 3AC354 B- 3AC356 B- 4BC357 B- 4BC358 B- 4BC359 B- 4BC360 B- 4BC361 B- 4BC363 B- 4BC364 B- 4AC365 B- 4AC366 B- 4AC367 B- 4AC368 B- 4AC369 B- 4AC370 B- 4AC371 B- 4AC372 B- 4AC373 B- 4AC374 B- 4AC375 B- 4AC376 A- 4AC377 A- 4AC378 A- 4AC379 B- 3AC380 B- 3BC381 B- 4BC382 B- 4BC383 B- 4BC384 B- 4BC385 A- 3AC386 B- 4BC387 B- 4BC388 B- 4BC389 B- 4AC391 A- 4AC392 A- 4AC395 B- 4AC401 B- 4CC402 B- 4BC403 B- 4BC404 B- 4BC405 B- 4BC406 B- 4BC407 B- 4BC408 B- 4BC421 B- 4BC422 B- 4BC423 B- 4BC424 B- 4BC425 A- 4BC426 A- 4BC427 A- 4BC428 A- 4BC429 A- 5B
C430 A- 5BC431 A- 5BC432 A- 5BC433 A- 5BC434 A- 5BC435 A- 5BC436 B- 5AC437 B- 4AC438 B- 5AC439 B- 5AC440 B- 5AC441 B- 5AC442 B- 5AC443 B- 4AC444 B- 4AC445 B- 5CC446 B- 5CC447 B- 5CC448 A- 4AC449 B- 4CC450 B- 5BC451 B- 5CC452 B- 4CC453 A- 4BC454 A- 4BC455 B- 4BC456 B- 4AC457 B- 5AC458 B- 5AC459 B- 5AC469 A- 4CC470 A- 4BC471 A- 4BC472 A- 4BC473 A- 4BC474 A- 4BC475 A- 4BC476 A- 4BC477 A- 4BC480 B- 5AC481 B- 4AC482 B- 4AC483 B- 4AC484 B- 4AC485 B- 4AC486 B- 4AC487 A- 5BC488 A- 5BC489 A- 4BC496 A- 4BC497 A- 4BC498 A- 4BC499 A- 4BC500 A- 4AC501 B- 4CC502 B- 4CC510 A- 3CC515 A- 3CC516 A- 3BC517 A- 4CC518 A- 4CC601 B- 3C
C602 B- 3CC603 B- 3CC604 A- 2CC606 B- 3BC607 B- 3CC608 B- 3CC609 B- 3BC610 B- 3BC612 B- 3CC615 B- 3CC617 B- 2BC618 B- 2CC620 B- 3BC621 B- 3CC622 B- 3BC625 B- 2BC626 B- 3CC627 B- 2CC657 A- 1BC658 A- 1CC659 B- 3CC663 A- 3CC664 A- 2CC666 A- 3BC667 A- 1BC669 A- 1BC671 A- 2BC672 A- 2CC673 A- 2BC674 A- 3CC675 A- 1CC676 A- 2CC677 A- 1BC679 A- 1CC681 A- 1BC683 A- 1BC684 B- 2CC686 A- 1BC687 A- 3CC688 B- 1CC689 B- 2CC690 B- 2CC691 A- 3CC692 A- 3CC693 A- 3CC695 B- 2CC697 B- 2CC698 B- 1C OTHER X351 B- 4AX401 B- 4BX402 B- 4C TH201 A- 2BTH401 B- 4C CN1 A- 2BCN2 A- 4ACN3 A- 1ACN4 A- 2BCN5 A- 4B
CN6 A- 3CCN7 A- 2ACN8 A- 3ACN10 A- 3CCN101 A- 2BCN191 A- 3BCN201 B- 1ACN202 B- 2ACN303 A- 2BCN304 A- 2BCN305 A- 3ACN306 A- 3ACN307 A- 3ACN308 A- 3ACN309 A- 3ACN310 A- 3ACN311 A- 3ACN351 B- 3ACN352 B- 4ACN353 A- 2ACN354 A- 4ACN355 B- 3ACN356 A- 3ACN357 A- 2ACN402 A- 4CCN405 A- 5BCN406 A- 5BCN407 A- 5BCN408 A- 5BCN409 A- 5BCN412 A- 4BCN413 B- 5ACN414 B- 4ACN415 B- 5ACN416 B- 5ACN417 B- 5ACN418 B- 5ACN419 B- 4ACN421 B- 4BCN422 B- 5BCN423 A- 5BCN424 A- 5BCN436 A- 4CCN437 A- 4CCN439 A- 5BCN443 A- 5BCN445 B- 4CCN447 B- 4BCN450 A- 4BCN452 A- 4CCN453 A- 4BCN454 B- 4CCN455 A- 5BCN456 A- 2CCN457 A- 2CCN458 A- 2CCN460 A- 2CCN602 A- 1CCN604 A- 1BCN605 A- 1BCN623 B- 3CCN624 B- 3C
CN650 A- 2CCN651 A- 2CCN652 A- 2C CP1 A- 2ACP2 A- 2BCP301 A- 3ACP302 A- 3ACP303 A- 3ACP351 B- 4BCP352 B- 4BCP401 B- 4ACP402 A- 4BCP403 A- 3ACP404 A- 3BCP405 A- 3BCP406 B- 4CCP408 A- 4BCP409 A- 4BCP410 A- 4CCP411 A- 4CCP412 A- 4CCP413 A- 4BCP414 A- 4BCP601 B- 3C E101 B- 3AE301 A- 3AE351 B- 4BE401 B- 5BE601 B- 3C F1 A- 1BF2 A- 2CF650 A- 1B J651 A- 2CJ652 A- 1C L1 A- 1BL3 A- 4CL4 A- 5CL5 A- 5CL6 A- 5CL7 A- 5CL8 A- 4AL9 A- 4AL10 A- 4AL11 A- 3CL12 A- 4CL13 A- 3CL111 A- 3BL112 A- 3BL121 B- 2AL131 B- 2AL132 B- 2AL133 B- 3AL134 B- 2BL135 B- 2AL136 B- 3AL137 B- 3AL138 B- 3A
L151 B- 2AL152 B- 2AL153 B- 2AL154 B- 3AL155 B- 3AL156 B- 3AL157 B- 3AL158 B- 3AL181 A- 3BL191 A- 3BL192 A- 3BL201 B- 2AL202 B- 2AL203 B- 2AL204 B- 1AL205 B- 3BL206 B- 3BL207 B- 3BL208 B- 3BL209 B- 3BL210 B- 1BL211 B- 2BL212 B- 3BL213 B- 2BL214 B- 2BL215 B- 1AL216 B- 1AL217 B- 1AL218 B- 2BL301 A- 3BL302 A- 2AL303 A- 3BL304 A- 3BL307 A- 2AL308 A- 2AL309 A- 2AL310 A- 2AL311 A- 2BL312 A- 2AL313 A- 2BL314 A- 2BL315 A- 3BL351 B- 3BL352 B- 4BL353 B- 4AL354 A- 4AL358 B- 4AL359 B- 4AL361 B- 4AL365 B- 4BL366 B- 3BL401 B- 4CL402 B- 4BL404 A- 5BL405 A- 4BL406 A- 4BL407 A- 5BL408 A- 5BL409 B- 5AL410 B- 4CL411 A- 5BL412 A- 5B
L413 A- 5BL414 A- 5BL415 A- 5BL416 A- 5BL417 B- 5BL427 A- 4CL428 A- 4CL429 A- 3CL430 A- 3CL431 A- 3BL601 B- 3CL604 B- 2CL605 B- 2CL608 B- 3BL609 B- 3CL610 A- 3CL612 A- 3CL613 B- 3CL622 A- 1BL623 A- 1BL635 B- 2C
(No.RA053<Rev.001>) 2-8 2-8 (No.RA053<Rev.001>)
B
A
654321
R2
32
R2
31
R2
30
R2
29
R2
28
R2
27
R2
09
R2
08
R207
R206
R2
05
R204
R203
R2
01
R189
R185
R183
R1
74
R1
70
R1
55
R1
48
R147
R146
R1
45
R143
R1
42
R1
41
R132
R122
R121
R120
R119
R118
R117
R116
R115
R114
R113
R112
R111
Q2
29
Q2
28
Q2
27
Q201 Q141
L202
L201
L187
L1
78
L1
76
L1
73
L1
56
L1
53
L1
52
L151
IC2
01
D2
27
D2
21
D202
D201
D1
81
D1
80
D144
D143
D142
D141
D132
D120
D119
D118
D117
D116
D115
D114
D1
13
D1
12
D111
CP
20
3C
P2
02
CP
20
1
CP
14
1
CN
15
4
CN
15
3C
N1
52
CN
15
1
C2
07
C206
C205
C204
C203
C202
C2
01
C1
92
C1
90
C186 C184
C179
C1
77
C175C172C
15
8
C149
C148
C147
C146
C145
C144
C143
C142
C141
J7C-0217-10
XC1-2091/2 #0
CN
20
1
A1
51
S1
12
S113
S114
S115
S116
S131
S1
17
S132S118
S1
19
S1
20
S121
S1
22
S123
S1
24
S1
25
S126
S1
27
S1
28
S1
29
S1
30
IC2
01
1
BT
GPS
MIC
10
1
S111
J7C-0217-10
XC1-2092/2 #1S301 S302 S303 S304
DISPLAY UNIT (XC1-209K-00 (NX-3220(K,E3),NX-3320(K,E3)), XC1-209K-01 (NX-3220(K2,E2),NX-3320(K2,E2)), XC1-209K-02 (NX-3220(K3,E),NX-3320(K3,E)))
--- Component side view (J7C-0217-10) ---
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
IC IC201 A- 4B
TRANSISTOR Q141 A- 4BQ201 A- 4BQ227 A- 2AQ228 A- 2BQ229 A- 2B
DIODED111 A- 5BD112 A- 5AD113 A- 5BD114 A- 5AD115 A- 6AD116 A- 6BD117 A- 6BD118 A- 6AD119 A- 6BD120 A- 6BD132 A- 5B
D141 A- 4AD142 A- 4AD143 A- 4AD144 A- 4AD180 A- 4AD181 A- 4AD201 A- 4AD202 A- 4BD221 A- 2AD227 A- 2B
RESISTORR111 A- 5BR112 A- 5AR113 A- 5BR114 A- 5AR115 A- 6AR116 A- 6BR117 A- 6BR118 A- 6AR119 A- 6BR120 A- 6B
R121 A- 6AR122 A- 6AR132 A- 5BR141 A- 4BR142 A- 4BR143 A- 4BR145 A- 4BR146 A- 4BR147 A- 4BR148 A- 4BR155 A- 3AR170 A- 3AR174 A- 4AR183 A- 4AR185 A- 4AR189 A- 4AR201 A- 2BR203 A- 4BR204 A- 4AR205 A- 4BR206 A- 3AR207 A- 4B
R208 A- 4BR209 A- 4BR227 A- 2AR228 A- 2BR229 A- 2BR230 A- 2AR231 A- 2BR232 A- 2B
CAPACITORC141 A- 4AC142 A- 4AC143 A- 4AC144 A- 4AC145 A- 4BC146 A- 4AC147 A- 4BC148 A- 4BC149 A- 4BC158 A- 3AC172 A- 3AC175 A- 4A
C177 A- 4AC179 A- 4AC184 A- 4AC186 A- 4AC190 A- 4AC192 A- 4AC201 A- 3BC202 A- 2BC203 A- 2BC204 A- 2BC205 A- 2BC206 A- 4BC207 A- 2B
OTHERCN151 A- 2ACN152 A- 3ACN153 A- 3ACN154 A- 3ACN201 A- 2BS111 A- 5AS112 A- 5B
S113 A- 5BS114 A- 5AS115 A- 5BS116 A- 5AS117 A- 5BS118 A- 5BS119 A- 5AS120 A- 5BS121 A- 5BS122 A- 6AS123 A- 6BS124 A- 6BS125 A- 6AS126 A- 6BS127 A- 6BS128 A- 6AS129 A- 6BS130 A- 6BS131 A- 5AS132 A- 5BS301 A- 1BS302 A- 2B
S303 A- 3BS304 A- 3BCP141 A- 4ACP201 A- 2BCP202 A- 2BCP203 A- 2AA151 A- 4AL151 A- 2AL152 A- 2AL153 A- 2AL156 A- 3AL173 A- 4AL176 A- 4AL178 A- 4AL187 A- 4AL201 A- 2BL202 A- 4BMIC101 A- 2A
(No.RA053<Rev.001>) 2-9 2-9 (No.RA053<Rev.001>)
A-1C
Side Y axisX axis
ADDRESS TABLE OF BOARD PARTS
Each address may have an address error by one interval.
REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION
TRANSISTORQ221 B- 2AQ222 B- 2AQ223 B- 2A
RESISTORR1 B- 3BR2 B- 3BR3 B- 3BR191 B- 5AR221 B- 2A
R222 B- 2AR223 B- 2A
CAPACITORC101 B- 2AC102 B- 2AC193 B- 5A
OTHERCN155 B- 3ACN156 B- 3A
CN157 B- 5ACN158 B- 5ACN202 B- 4BCN301 B- 1BL101 B- 2AL102 B- 2AL194 B- 5A
B
A
6 5 4 3 2 1
R2
23
R2
22
R2
21
R191
R3
R2
R1
Q2
23
Q2
22
Q2
21
L1
94
L1
02
L1
01
CN301
CN158CN157
CN
15
6
CN155C193
C1
02
C1
01
R1
R2
R3
R4
CN202
+
-
BT
GP
S
1
DISPLAY UNIT (XC1-209K-00 (NX-3220(K,E3),NX-3320(K,E3)), XC1-209K-01 (NX-3220(K2,E2),NX-3320(K2,E2)), XC1-209K-02 (NX-3220(K3,E),NX-3320(K3,E)))
--- Foil side view (J7C-0217-10) ---
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-10 2-10 (No.RA053<Rev.001>)
1/E
MG
2G
ND
3/S
IDE
2
4/S
IDE
1
5/P
TT
6N
C
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1 2 3 4 5 6
+-S
BA
TT
SP
TX-RX Unit
XC1-178(NX-3220)
DISPLAY Unit
ANT
Power SW/ CHANNELAF Vol SELECTOR
CN602
SP-
SP+
GPS
Bluetooth
CN354
CN353C
N1
CN
7
GND
GND
50A
50A
INTM_M
ME
/KEYI4
/KEYI3
/KEYI2
/KEYI1
/KEYI0
GND
KEYO3
KEYO2
GND
LED_B
KEYO1
LED_R
KEYO0
LED_G
LBC_G
LBC_R
LBC_B
LCD_A0
LCD_/CS
GND
18M
32M
32M
WR1_/OE
WR0_/WR
/LCD_RST
DB[0]
DB[1]
LCD_BLC
(To DISPLAY Unit)
3
2
45
B C D E FA
1
SB
1
NC
GN
D
VO
L
50
A
+B
EN
C2
EN
C3
EN
C0
EN
C1
GN
D
EN
C0
NC
NC
NCEXTSPDET
EXTM_MPTT/RXD
50JAE
/OPTDET
SPO
TXD
J651
J652
GND
GND
50A
50A
ME
GND
GND
LED_B
LED_R
LED_G
LBC_G
LBC_R
LBC_B
LCD_A0
LCD_/CS
GND
18M
32M
32M
WR1_/OE
/LCD_/RST
LCD_BLC
DB[2]
DB[5]
DB[4]
DB[7]
DB[3]
DB[6]
XC1-209 A/2
XC1-209 B/2
CN202CN402
DB7
A+
K-
VLCD
VB0-
VB1-
VB1+
VB0+
VDDI
VSS
/CS0
DB2
A0
DB3
E(WR1)
DB4
R/W(WR0)
DB5
/RST
DB6
DB0
DB1
VDDA
VSS
NC
CN201
CN
30
1
/SID
E2
/EM
G
/PT
T
/SID
E1
GN
D
NC
DISPLAY Unit
GP
S
Blu
eto
oth
MIC101
MIC
LC
D
GN
D
Bluetooth GPS
WR0_/WR
DB[7]
DB[3]
DB[6]
DB[0]
DB[1]
DB[2]
DB[5]
DB[4]
INTM_M
KEYO1
KEYO0
/KEYI4
/KEYI3
/KEYI2
/KEYI1
/KEYI0
KEYO3
KEYO2
ME
INT
M_
M
INTERCONNECTION DIAGRAM
XC1-180(NX-3320)
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-11 2-11 (No.RA053<Rev.001>)
Receiver Section
RF (Center Frequency) AF (1kHz)
D201 C311 CN604
ANT D205 IC601 CN605
D202
C246 D203 C344 C334 IC303 IC401 Internal Speaker
IC650
C195
External Speaker
C683
To make measurements in the AF section, connect the AC level meter.
(ANT input: –53dBm, 1kHz FM, 3kHz DEV (Wide). SP output: 500mW@8ohm Load)In the RF section, use 470pF coupling capacitor.(The display shows the SSG input value required to obtain 12dB SINAD.)
Transmitter Section
AF (1kHz) AF (1kHz) RF (Center Frequency)
(Mod) (Local)
INTM_M IC601 IC401 C345 C195 D201
Internal MIC D205
D202
IC303 C218 IC202 C225 Q201 C237 Q202 C227 D203 C246
EMC
External MIC
* Transmit frequency : 155MHz
LPFANTSW
HPF Transceiver IC
VCO
MPU/DSP
CODEC
-121.5dBm -123.0dBm -123.5dBm
5.65Vp-p
CODEC MPU/DSP Pre-
DriveDrive Final LPF
ANTSW
12.5mVrms 3dBm 14dBm 25dBm 38dBm 38dBm 5W
HPF
-107.5dBm
-5dBm ~ +5dBm
-122.5dBm
Transceiver IC
VCO
78.9mVrms -5~5dBm
LEVEL DIAGRAM
ANT
NX-3220
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-12 2-12 (No.RA053<Rev.001>)
Receiver Section
RF (Center Frequency) AF (1kHz)
C311 CN604
ANT D201 IC601 CN605
D202
C246 D203 C344 C334 IC303 IC401 Internal Speaker
IC650
C195
External Speaker
C683
To make measurements in the AF section, connect the AC level meter.
(ANT input: –53dBm, 1kHz FM, 3kHz DEV (Wide). SP output: 500mW@8ohm Load)In the RF section, use 470pF coupling capacitor.(The display shows the SSG input value required to obtain 12dB SINAD.)
Transmitter Section
AF (1kHz) AF (1kHz) RF (Center Frequency)
(Mod) (Local)
INTM_M IC601 IC401 C345 C195
Internal MIC D201 ANT
D202
IC303 C218 IC202 C225 Q201 C237 Q202 C227 D203 C246
EMC
External MIC
* Transmit frequency : 485MHz
LPFANTSW HPF Transceiver IC
VCO
MPU/DSP
CODEC
-120.0dBm -121.5dBm -122.0dBm
5.65Vp-p
CODEC MPU/DSP Pre-
DriveDrive Final LPF
ANTSW
12.5mVrms 2dBm 14dBm 25dBm 38dBm 38dBm 5W
HPF
-107.5dBm
-5dBm~+5dBm
-121.0dBm
Transceiver IC
VCO
84mVrms -5~5dBm
NX-3320
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-13 2-13 (No.RA053<Rev.001>)
1 2
BATT 7.5V
GND
+B
LPFANT
SWFINALAMPAMP
RD07MUS2BT514Q202Q201
DRIVE
D201 RN142S
APC
/APCSW
136-174MHz
SW50C
ANTSW
IC201XC8102AA07-G
DC SW APCSW2
DC SWDC SW
+B
APC
Q206Q205SSM3K15AMFV
Q204LTC044EEBFS8
IC203BA3472FVM
Q207EMD12
SSM3K15AMFV
RD01MUS2BT513BGU6104IC202
50T
DC SW
/DSW
Q203LSCR523EBFS8
RF
LPF
50C Ripple
FilterDC SW
/SAVE
Q1812SC5108FT/Y/
Q114VT6M11SS400SMD111
2SD2654/W/Q113
IC9XC6209B312D-G
3.1V Reg1.2V Reg
IC10XC6215B122N-G
31BU12BU
3.8V DC/DCConverter
1.2V DC/DCConverter12M
38M
18M1.8V DC/DCConverter
XC61CC5602N-GIC1
Detect/BINT
SWSB1
DAN222EMD12Q1
D8
38M
3.2V Reg
32M
5V Reg50A
SBC
SBC
3.2V Reg32C
TXC
50T
DC SW
SBC
BATT
53AF AFSW(Reg)
VT6M1Q4
50A
LTC014EEBFS8Q62SB1132(Q.R)Q71BU7242NUXIC18
FZA10BH-R50F2
FZA10BQ-3R15
F1
IC15XC6209B502D-G
XC6209B502D-GIC6
IC17XC6209B502D-G
SSM6N15AFEMQ3
SBC
TPS62140RGTIC3
VT6M1Q5
IC2LXDC2XQ12A-252
IC4LXDC2HN18F163
DC SW18M_3
32A
IC12XC8102AA07-G
32M
32A
IC11NJM2878F4-32
IC5XC6223D321G-G
IC14BU32TD2WNVX
ADS7961SRHBIC409
ADCBATT,CV,TEMP,THP,Ramp_Offset,SDET,VOL,FEM_PWR,FEM_ALM,ANTCHK
IC410
DAC
DAC124S085CIS
APC,ASSIST,FCNT
CN7
/KEYI0~/KEYI4,KEYO0~KEYO3,
KXCJ9-1008
I2CCK,I2CDT
To
DIS
PL
AY
Un
it (
A/2
)
RK74HB1J101JCP410,CP411,CP412
CN402
IC401
IC402
IC404
DDR_A[0]~DDR_A[13]DDR_BA[0],DDR_BA[1]DDR_CAS,DDR_CKE,DDR_CLKNDDR_CLKP,DDR_CSDDR_DQM[0],DDR_DQM[1]DDR_RAS,DDR_WEDDR_DQS[0],DDR_DQS[1]DDR_D[0]~DDR_D[15]
/CS2
/CS3
/CS_F
BT_CLK
CN1
VOL
ENC0~ENC3
+B
TX-RX UNIT (XC1-178)
D202 RN142SD203 RN142S
SSDET
20V DC/DCConverter
IC13TPS61041DRVR
200C
32M
/LCD_RST,LCD_BLC
LCD_/CS,/WR1_/OE,/WR0_/WRLCD_A0,DB[0]~DB[7]
MotionSensor
-----------------------------------------------------------TX--ANTSW,APCSW2,/APCSW,/DSW,TXC-----------------------------------------------------------VCO--/SAVE,ASTSW-----------------------------------------------------------DC SW(Q3)--/BINT-----------------------------------------------------------5V AVR(IC651)--5VC-----------------------------------------------------------5V AVR(IC6),3.2V AVR(IC14),DC SW(Q4)--SBC-----------------------------------------------------------Detect(IC403)--/RST-----------------------------------------------------------OTHERS--SYMTIM_IN,SYMTIM_IN(OUT)---------------------------------------------------------
Detect
IC403S-80135ANPF-G
/RST
50C
TEMP
THP
Ramp_OffsetVCO
/DCR_RST,RX,TX,AGCKEEP,BCLK,/DCR_CS,DCR_DO,DCR_DI,DCR_ACLK,
TRANCEIVER IC
AK2401IC303
ATT
LNAoUT
VCO_MOD
PLL_CLK
PLD,DCR_ADI,/DCR_ACS,/DCR_DCS,DCR_DDO
ATT HPF Protect
D301,3021SS400SM
LoopFilter
CP
CPZ
50C
CV
IC102BU7295HFV
50C
32C
200CIC101
ASSIST
ASTSW
DC SW
OPA170AIDRLR Q102 EM6M2D102 EDVZ8.2B
Q131
D131
D132,133,134,D135SMV1251-079LF
MCH3914-H/8/
SMV1801-079LF
D136SMV1130-079LF
VCO_MOD
AMP
32C
DC SW/SAVE
VT6M1Q103
AMPDRIVEPre
/PSW
SSM6N15AFEMQ2
56DET3.2V Reg
5V Reg
5V Reg
5VC
5V Reg50J
IC651NJM6209B502D-G
+B_AF AF SW
GPIO5
LTC014EEBFS8Q653
2SB1694Q650
FZA10BH-R315F650
SB1
50A
IC405TC7SZ08FE
DDR18M
32M FLASHDATA[0]~DATA[15]
/FRST,/OE,/WP,/WRADD[0]~ADD[23]
/CS4,/OE,/WR,ADD[23]DATA[0]~DATA[7]
18M
50A
INTM_M
ME
LED_R,LED_G,LED_B,LBC_R,LBC_G,LBC_B
19.2MHz
TCXO Buffer
32M
PLL_CLK
Q4012SC4617/S/
L7H-0076-00X401
FCNT
32M
TEMP TEMP
SCK1,SDO1
SCK0,SDO0.SDI0
/DACCS
/ADC,/ADC_INT
IC406
32M
VO
L/E
NC
/EMG,/INT_PTT,/SIDE1,/SIDE2
To
DIS
PL
AY
Un
it (
B/2
)
DCSW
DCSW
Q654LTC044EEBFS8
SPO_MUTE
Q653
AFSW
LTC014EEBFS8
+BQ650
Q651, Q652
IC650
Q654
2SB1694
SSM3K324RF
TA7368FG
LTC044EEBFS8
CODEC_DI,CODEC_DO/CINT,BCLK,WCLK
IC601
CODECI2CCK,I2CDT
INTM_M
EXTM_M
ME
EXTSPDET
IC652TC7SET125FUF
TXD1TXD
/TXD1_JK_EN
GND
50J
/OPTDET
EXTM_M
DC SW
Q656RE1C001UN
EXTMIC_SW
RTT/RXDTC7SZ08FEIC654
/EXT_PTT
RXD1
32M
SPO
D205 RN142S
RF
Q1512SC5108FT/Y/
AMP
J651
J652
CN602
BLOCK DIAGRAM
12M 18M 32M 32A 53AF
GPS
18BT32BT
1575.42MHz
BLUETOOTH
IC351
BPF
L7K-0059-00L359
SAW
L79-1987-05L361
2400-2483.5 MHz
18BT
LEVEL
32BT
CONVERSION
18BT_TX,18BT_RX18BT_CTS,18BT_RTS
18BT_AFSYNC,18BT_ACLK18BT_AOUT,18BT_AIN
IC352 , IC35374AVC4TD245GU
CLK18BT X351L77-3121-05
BT_AUD_DI,BT_AUD_DOWCLK,BCLK
RTS2,CTS2RXD2,TXD2,
BT_CLK
GPS_PA_EN/BT_SHUTDOWN
ANTDET
FEM_PWR
FEM_ALM
GPS
BLUETOOTH
To DISPLAY Unit (A/2)
28GPS
32.768kHz
18BT 1.8V Reg
BU18TD2WNVXIC8
32BT
IC7BU33TD2WNVX
3.2V Reg
TX-RX UNIT (NX-3220)
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-14 2-14 (No.RA053<Rev.001>)
1 2
BATT 7.5V
GND
+B
LPFANT
SWFINALAMPAMP
RD08MUS2Q202Q201
DRIVE
D201 L5208F
APC
/APCSW
400-520MHz
SW50C
ANTSW
IC201XC8102AA07-G
DC SW APCSW2
DC SWDC SW
+B
APC
Q206Q205SSM3K15AMFV
Q204LTC044EEBFS8
IC203BA3472FVM
Q207EMD12
SSM3K15AMFV
RD01MUS2BT513BGU6104IC202
50T
DC SW
/DSW
Q203LSCR523EBFS8
VCO_H
RF
LPF
50C Ripple
Filter
DC SW
DC SW
/SAVE
Q1812SC5108FT/Y/
Q112
Q114VT6M1
1SS400SMD1112SD2654/W/Q113
Q131
D131
D132,133,134BBY58-02V
BFU660F
BB555-02VH
IC9XC6209B312D-G
3.1V Reg1.2V Reg
IC10XC6215B122N-G
31BU12BU
3.8V DC/DCConverter
1.2V DC/DCConverter12M
38M
18M1.8V DC/DCConverter
XC61CC5602N-GIC1
Detect/BINT
SWSB1
DAN222EMD12Q1
D8
38M
3.2V Reg
32M
5V Reg50A
SBC
SBC
3.2V Reg32C
TXC
50T
DC SW
SBC
BATT
53AF AFSW(Reg)
VT6M1Q4
50A
LTC014EEBFS8Q62SB1132(Q.R)Q71BU7242NUXIC18
FZA10BH-R50F2
FZA10BQ-3R15F1
IC15XC6209B502D-G
XC6209B502D-GIC6
IC17XC6209B502D-G
SSM6N15AFEMQ3
SBC
TPS62140RGTIC3
VT6M1Q5
IC2LXDC2XQ12A-252
IC34LXDC2HN18F163
DC SW18M_3
32A
IC12XC8102AA07-G
32M
32A
IC11NJM2878F4-32
IC5XC6223D321G-G
IC14BU32TD2WNVX
ADS7961SRHBIC409
ADCBATT,CV,TEMP,THP,Ramp_Offset,SDET,VOL,FEM_PWR,FEM_ALM,ANTCHK
IC410
DAC
DAC124S085CIS
APC,ASSIST,FCNT
CN7
/KEYI0~/KEYI4,KEYO0~KEYO3,
KXCJ9-1008
I2CCK,I2CDT
To
DIS
PL
AY
Un
it (
A/2
)
L79-1984-05CP410,CP411,CP412
CN402
IC401
IC402
IC404
DDR_A[0]~DDR_A[13]DDR_BA[0],DDR_BA[1]DDR_CAS,DDR_CKE,DDR_CLKNDDR_CLKP,DDR_CSDDR_DQM[0],DDR_DQM[1]DDR_RAS,DDR_WEDDR_DQS[0],DDR_DQS[1]DDR_D[0]~DDR_D[15]
/CS2
/CS3
/CS_F
BT_CLK
CN1
VOL
ENC0~ENC3
+B
TX-RX UNIT (XC1-180)
D202 RN142SD203 RN142S
SSDET
20V DC/DCConverter
IC13TPS61041DRVR
200C
32M
/LCD_RST,LCD_BLC
LCD_/CS,/WR1_/OE,/WR0_/WRLCD_A0,DB[0]~DB[7]
MotionSensor
-----------------------------------------------------------TX--ANTSW,APCSW2,/APCSW,/DSW,TXC-----------------------------------------------------------VCO--/SAVE,ASTSW,VCO_H_/L-----------------------------------------------------------DC SW(Q3)--/BINT-----------------------------------------------------------5V AVR(IC651)--5VC-----------------------------------------------------------5V AVR(IC6),3.2V AVR(IC14),DC SW(Q4)--SBC-----------------------------------------------------------Detect(IC403)--/RST-----------------------------------------------------------OTHERS--SYMTIM_IN,SYMTIM_IN(OUT)---------------------------------------------------------
Detect
IC403S-80135ANPF-G
/RST
50C
TEMP
THP
Ramp_Offset
VT6M1
VCO_L
VCO_H_/L
RE1E002SP
DC SW
Q111
/DCR_RST,RX,TX,AGCKEEP,BCLK,/DCR_CS,DCR_DO,DCR_DI,DCR_ACLK,
TRANCEIVER IC
AK2401IC303
ATT
LNAoUT
VCO_MOD
PLL_CLK
PLD,DCR_ADI,/DCR_ACS,/DCR_DCS,DCR_DDO
ATT HPF Protect
D301,3021SS400SM
LoopFilter
CP
CPZ
50C
CV
IC102BU7295HFV
50C
32C
200CIC101
ASSIST
ASTSW
DC SW
OPA170AIDRLR Q102 EM6M2D102 EDVZ8.2B
D1351SV305FT
Q151
D151
D154BBY58-02V
D155
BFU660F BB555-02VH
BB555-02VHD152,153
SMV1130-079LF
DC SW
DC SW
VCO_MOD
VCO_MOD
AMP
32C
DC SW/SAVE
VT6M1Q103
AMPDRIVEPre
Q116
SSM3K15AMFVQ115
/PSW
SSM6N15AFEMQ2
56DET3.2V Reg
5V Reg
5V Reg
5VC
5V Reg50J
IC651NJM6209B502D-G
+B_AF AF SW
GPIO5
LTC014EEBFS8Q653
2SB1694Q650
FZA10BH-R315F650
SB1
50A
IC405TC7SZ08FE
DDR18M
32M FLASHDATA[0]~DATA[15]
/FRST,/OE,/WP,/WRADD[0]~ADD[23]
/CS4,/OE,/WR,ADD[23]DATA[0]~DATA[7]
18M
50A
INTM_M
ME
LED_R,LED_G,LED_B,LBC_R,LBC_G,LBC_B
19.2MHz
TCXO Buffer
32M
PLL_CLK
Q4012SC4617/S/
L7H-0076-00X401
FCNT
32M
TEMP TEMP
SCK1,SDO1
SCK0,SDO0.SDI0
/DACCS
/ADC,/ADC_INT
IC406
32M
VO
L/E
NC
/EMG,/INT_PTT,/SIDE1,/SIDE2
To
DIS
PL
AY
Un
it (
B/2
)
Q654LTC044EEBFS8
SPO_MUTE
CODEC_DI,CODEC_DO/CINT,BCLK,WCLK
IC601
CODECI2CCK,I2CDT
EXTSPDET
IC652TC7SET125FUF
TXD1TXD
/TXD1_JK_EN
GND
50J
/OPTDET
EXTM_M
DC SW
Q656RE1C001UN
EXTMIC_SW
RTT/RXDTC7SZ08FEIC654 /EXT_PTT
RXD1
32M
SSM3K15AMFV
J651
J652
CN602
12M 18M 32M 32A 53AF
GPS
18BT32BT
1575.42MHz
BLUETOOTH
IC351
BPF
L7K-0059-00L359
SAW
L79-1987-05L361
2400-2483.5 MHz
18BT
LEVEL
32BT
CONVERSION
18BT_TX,18BT_RX18BT_CTS,18BT_RTS
18BT_AFSYNC,18BT_ACLK18BT_AOUT,18BT_AIN
IC352, IC35374AVC4TD245GU
CLK18BT X351L77-3121-05
BT_AUD_DI,BT_AUD_DOWCLK,BCLK
RTS2,CTS2RXD2,TXD2,
BT_CLK
GPS_PA_EN/BT_SHUTDOWN
32.768kHz
ANTDET
FEM_PWR
FEM_ALM
GPS
BLUETOOTH
To DISPLAY Unit (A/2)
28GPS
32BT
IC7BU33TD2WNVX
3.2V Reg
18BT 1.8V Reg
IC8BU18TD2WNVX
TX-RX UNIT (NX-3320)
DCSW
DCSW
Q653
AFSW
LTC014EEBFS8
+BQ650
Q651, Q652
IC650
Q654
2SB1694
SSM3K324RF
TA7368FG
LTC044EEBFS8
INTM_M
EXTM_M
ME
SPO
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-15 2-15 (No.RA053<Rev.001>)
CN202
CN201
DB[0]~DB[7],LCD_/CS,WR1_/OE,WR0_/WR,LCD_A0
32M
50A
32M
18M
18M
/LCD_RST /RST
/LCD_RST
KEY
ILLUMINATION
LCD
BACKLIGHTD111-D120D132B30-2365-05
D201,D202NSSW206C-T865
TX/BUSY
LED
D221
DCSW
Q141
EMD9Q201
DCSWLCD_BLC
50A
LED_R
LTC014EEBFS8
Q222
DCSW
LED_GDCSW
DCSWLED_B
50A
Q221
Q223
LCD_BLC
LIGHTBAR
LED
D227NESM238B
LBC_R
LTC014EEBFS8
Q228
DCSW
LBC_GDCSW
DCSWLBC_B
50A
Q227
Q229
50A
EMD9
LCD_BLC
TC7SZ08FEIC201
A+
/EMG,/PTT,/SIDE1,/SIDE2
INTM_M
ME T91-0673-25MIC101
CN301
/KEYI0-4,KEYO0-3
LED_R,LED_G,LED_B
LBC_R,LBC_G,LBC_B
NESM238B
KEY MATRIX
EMG
PTT
SIDE1
SIDE2
To
LC
D A
SS
Y
To
TX
-RX
UN
ITTo
TX
-RX
UN
IT
Bluetooth GPS
GPS
FRONTEND
MODULE
A151W0C-0267-00
28GPS
DISPLAY UNIT
DISPLAY UNIT (XC1-209 A/2)
DISPLAY UNIT (XC1-209 B/2)
A
1
2
3
4
5
B C D E F G(No.RA053<Rev.001>) 2-16 2-16 (No.RA053<Rev.001>)
L152
L1
53
L1
51
C1
90
R189 C192
C1
93
L1
94
R191
A151
L187
C1
86
R1
85
C1
84
R183
D181
D180
L1
78
L1
76
L1
73
R170 R174 C179C177C175C172
R155 L156 C158
-
-
R118R112
1.2k
R120
1k
560
R117R115
560
560
R113R116
PTT
3.2V
1.8V
5.0V
2.7V
RB521SM-30
-
2.2k
-
R209
10k
-
10k
R208
SIDE1
PTT
EMGDISPLAY UNIT (B/2)
SIDE2
D115 - D117
MIC/ME
-
-
-
RESERVER4
000
0 0
0
-
--
GPS/BT12KEY8KEYR3R2R1
K-02
K-01
K-00-
-
100
-
R142 - R143
-
1k
-
R132
-
S131 - S132
-
S70-0901-05
S122 - S130S119 - S121
-
-
S114 - S118
S70-0901-05S70-0901-05
-
S111 - S113
S70-0901-05
EMD9
-
EMD9
Q201
EMD9
-
EMD9
Q141
TC7SZ08FE
-
IC201
TC7SZ08FE
CP201 - CP203
NSSW206C-T865
-
D201 - D202
NSSW206C-T865
RB521SM-30
-
D141 - D144
-
D132
B30-2365-05-
-
B30-2365-05
D118 - D120
-
B30-2365-05
D111 - D114
B30-2365-05
-
R111 ,R114
1k
1k
-
-
RK74HB1J101J
RK74HB1J101J
CP141
RK74HB1J01J
-
RK74HB1J101J
EC720BP-0325A
CN201
EC720BP-0325A
-
0
-
0
R207
100
-
100
R206
1k
-
1k
R205
1k
-
1k
R204
10k
-
10k
R203
100
-
100
R201
100
R148
100
-
100
R147
-
-
-
R146
100
-
100
R145
-
-
4.7k
R141
4.7k
--
0
R122
-
-
-
R121
0
L202
LB73H0AV-002
-
LB73H0AV-002LB73H0AV-002
L201
LB73H0AV-002
-
0.1u
C207
0.1u
-
0.1u
-
0.1u
C206
0.1u
-
0.1u
C205
0.33u
0.33u
-
C204
2.2u
-
2.2u
C203
2.2u
2.2u
-
C202
0.1u
0.1u
-
C201
K-02
K-01
K-00
LCD
470p
470p
-
C141 - C144
K-02
K-01
K-00
KEYPAD
TX/BUSY
65
#0
987
4
HOME
321
HOME
RET
RET
MENU
MENU
HOME
Ki0
Ki1
Ki2
Ki3
Ki4
RET
Ko3Ko2Ko1Ko0
MENU
STD KEY
FULL KEY
DB
7
GPS
Bluetooth
LED_R
LED_B
GND
GND
LBC_B
LBC_R
LBC_G
LED_G
KEYo0
KEYo1
KEYo2
KEYo3
KEYi0
KEYi1
KEYi2
KEYi3
KEYi4
ME
MIC
50A
50A
GND
GND
LCD_BLC
LCD_DB7
LCD_DB6
LCD_DB5
LCD_DB4
LCD_DB3
LCD_DB2
LCD_DB1
LCD_DB0
LCD_/RST
LCD_R/W(WR0)
LCD_E(WR1)
32LCD
32LCD
18M
LCD_VSS
LCD_/CS
LCD_A0Ki0
Ki1
Ki2
Ki3
Ki4
Ko3Ko2Ko1Ko0
2
5
8 9
3
6
HOME
7
4
1
RET
#
0
MENU
VS
S
VD
DA
VI(
on
)=1
.6V
50A
32LCD
18M
DB
1
DB
0
DB
6
/RS
T
DB
5
R/W
(WR
0)
DB
4
E(W
R1
)
DB
3
A0
DB
2
/CS
0
VS
S
VD
DI
VB
0+
VB
1+
VB
1-
VB
0-
VL
CD
K-
A+
KEYo0KEYo1KEYo2KEYo3
KEYi0KEYi1
KEYi2
KEYi3KEYi4
/LC
DR
ST
18LCD
LCD_BL
ADD[23]
/OE
LCD_BL
DB[7]
DB[6]
DB[5]
DB[4]
DB[3]
DB[2]
DB[1]
DB[0]
/LCDRST
/WR
/CS4
/CS
4A
DD
[23
]/O
E/W
R
DB
[0]
DB
[1]
DB
[2]
DB
[3]
DB
[4]
DB
[5]
DB
[6]
DB
[7]
CN155
CN154
CN
15
8C
N1
57
CN156
CN151
CN153
CN152 EXP_PAD
11
PoSToUT10
NC<GND>2 9
LNAIN 8
PREoUT 7
GND_2 6PREIN5NC<GND>14VDD3VCTL2
GND_11
$C
18
2
10
00
p
10
00
p
47
0p
*C1
44
0.1u
*C206
0.1
u
*C2
05
25
0.3
3u
*C2
04
0.1
u
*C2
01
6.3
2.2
u
*C2
02 6.3
2.2
u
*C2
03
0.1
u*C
20
7
120p
10
00
p
1p
1.5p1p1.5p
$C
17
1
$C
16
3
47
0p
C1
02
47
0p
C1
46
$C
15
5
4p
$C
15
7
47
0p
C1
01
22p
47
0p
C1
49
47
0p
C1
48
47
0p
C1
47
47
0p
C1
45$C
12
7
47
0p
*C1
43
47
0p
*C1
42
47
0p
*C1
41
$C
11
3$
C1
30
$C
12
9
$C
12
8
$C
16
0
$C168$C166
$C
11
1$
C1
16
$C
11
9$
C1
22
$C
12
5
$C
11
4
$C
11
2$
C1
17
$C
12
0$
C1
23
$C
12
6
$C
11
5
$C
11
8$
C1
21
$C
12
4
$C164
6
5
4
3
2
1
E40-6883-05CN301
TO TX-RX UNIT XC1-178(NX-3220) XC1-180(NX-3320) CN7
TO LCD
TO TX-RX UNIT XC1-178(NX-3220)XC1-180(NX-3320)CN402
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC
72
0B
P-0
32
5A
*CN
20
1
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720BP-0341ACN202
RB521SM-30*D141
RN262CS
RN262CS
RB521SM-30*D143RB521SM-30*D142
RB521SM-30*D144
NS
SW
20
6C
-T8
65
*D2
02
NS
SW
20
6C
-T8
65
*D2
01
B30-2365-05*D118
B30-2365-05*D115
B30-2365-05*D116
B30-2365-05*D119
B30-2365-05*D111
B30-2365-05*D113
B30-2365-05*D117
B30-2365-05*D120
B30-2365-05*D112
B30-2365-05
*D114
B30-2365-05*D132
A_
BA
_R
K_
RA
_G
K_
B
K_
G NE
SM
23
8B
D2
27
A_
BA
_R
K_
RA
_G
K_
B
K_
G NE
SM
23
8B
D2
21
VCC
5
oUTY
4 GND 3
INA 2
INB 1
TC7SZ08FE
*IC201
27
n
4.7
n
12
n
15
n
1.2n
10n
6.8n
LB73H0AV-002*L202
LB73H0AV-002
L102
LB73H0AV-002*L201
LB73H0AV-002L101
3.9
n
$L
15
9
$L
16
7
$L
16
2
$L
16
5
3.9
n
T9B-0004-00MIC101
LT
C0
14
EE
BF
S8
Q2
29
LT
C0
14
EE
BF
S8
Q2
28
LT
C0
14
EE
BF
S8
Q2
21
LT
C0
14
EE
BF
S8
Q2
22
LT
C0
14
EE
BF
S8
Q2
23
LT
C0
14
EE
BF
S8
Q2
27
EM
D9
*Q2
01
EMD9*Q141
1k
*R112
0
$R
18
8
1k
*R115
1k
*R118
1k*R114
22
0
*R2
04
$R
22
4
$R
22
5
$R
22
6
0
*R2 *R3 $R4
22
0
*R2
05
10
0
*R2
06
1k
R2
27
0
27
0
R2
23
1k
R2
21
1.2
k
R2
22
10
0*R
20
1
100*R148
1k
*R116
1.2
k
R2
28
1k
*R119
1k
*R111
1k*R113
0
$R161
1k*R117
0
*R2
07
*R1
$R154
$R144
100*R147100*R146100*R145
1k
*R120
100*R143
4.7
k
*R1
41
100*R142
10k
*R203
2.2
k
R2
32
2.2
k
R2
31
2.2
k
R2
30
0*R121
$R169
1k*R132
0
27
0
R2
29
0
2.2k
*R20910k
*R208
0
0*R122
5678
4321
RK
74
HB
1J1
01
J
*CP
20
1
5678
4321
RK
74
HB
1J1
01
J
*CP
20
3
RK74HB1J101J
*CP141 5678
4321
RK
74
HB
1J1
01
J
*CP
20
2
S70-0516-05S302
S70-0516-05S303
S70-0516-05S304
S70-0516-05S301
S70-0901-05
*S125
S70-0901-05
*S122
S70-0901-05*S119
S70-0901-05*S114
S70-0901-05*S116
S70-0901-05
*S111
S70-0901-05
*S131
S70-0901-05
*S112
S70-0901-05
*S117
S70-0901-05
*S120
S70-0901-05
*S123
S70-0901-05
*S126
S70-0901-05*S115
S70-0901-05
*S118
S70-0901-05
*S121
S70-0901-05
*S124
S70-0901-05
*S127
S70-0901-05
*S132
S70-0901-05
*S129
S70-0901-05
*S130
S70-0901-05
*S128
S70-0901-05
*S113
DISPLAY UNIT (A/2)
DISPLAY UNIT (XC1-209K-00 (NX-3220(K,E3),NX-3320(K,E3)), XC1-209K-01 (NX-3220(K2,E2),NX-3320(K2,E2)), XC1-209K-02 (NX-3220(K3,E),NX-3320(K3,E)))
SCHEMATIC DIAGRAM
$CN401
Destination
1.2V
3.2V
3.2V
TXL:3.7VTXH:4.2V
TXL:7.3VTXH:7.2V
TX:0.8VRX:0V
TX1.7VRX:0V
5.4V
5.0V
1.8V
1.8V
5.0V
3.2V
T:5.0VR:0V
2.7V
4.1V
4.3V
T:3.2VR:3.2V
1.8V3.2V
1.8V
5.0V
3.2V
1.8V
1.8V
1.2V
1.2V
1.2V
3.2V
18.9V
5.0V
3.8V
3.2V
1.8V
3.2V
1.2V
1.8V
3.2V
1.8V
1.8V
3.1V 1.2V
3.2V
1.8V
7.5V
0K-00
ON Board Contact
Overlap
VCO BufferVCO
NC
NC
54
2
3 1
A
FEDCB
CV amp
32C
ASSIST
BLS
20V DC/DC
TH Tap
ON Board Plate
(OUT)
LC
D_
BL
C
LC
D_
DB
7
LC
D_
DB
6
LC
D_
DB
5
LC
D_
DB
4
LC
D_
DB
3
LC
D_
DB
2
LC
D_
DB
1
LC
D_
DB
0
LC
D_
/RS
T
LC
D_
R/W
(WR
0)
LC
D_
E(W
R1
)
32
LC
D
32
LC
D
18
M
LC
D_
VS
S
LC
D_
/CS
LC
D_
A0
LB
C_
B
LB
C_
R
LB
C_
G
LE
D_
G
KE
Yo
0
LE
D_
R
KE
Yo
1
LE
D_
B
GN
D
KE
Yo
2
KE
Yo
3
GN
D
KE
Yi0
KE
Yi1
KE
Yi2
KE
Yi3
KE
Yi4
ME
MIC
50
A
50
A
GN
D
GN
D
BLS
GPS&BLUETOOTH
LEVEL CONVERTOR
GPS RF
BT RF
(RXD)SHIFTLEVEL
TXD
SPO
OPTDET
AE
2P
IN J
AC
K C
ON
NE
CT
OR
32M50A
+B
50J
50J
PTT/RXDMICIN
PT
T/R
XD
TX
D
EXTSPDETNC
NCCONTROL TXSLOT =>
(EXTPTT) DC SW
(TXD)SHIFTLEVEL
18M
18M
SPKVDD
12M
32M
BLS
BLS
BLS
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
50A
18BT
APC
RX HPF
1/4
W
0.5A
12BU
12M
32A
32A
R9
2-3
75
6-0
5
DDR
BO
OT
[3]
50A
BO
OT
[7]
Load Switch
18M_3
SB2
3.15A
50A
ANT_SW/LPF
16
V
25REF32A
16
V
LOW = UART OR USB LOADER
BO
OT
[0]
FOr BYTE PORT
BO
OT
[2]
BO
OT
[6]
BO
OT
[4]
50A
50A
18M
38M 18M_3
+
18M
18M
S
38M
-
50T
Flash
32A
32M
50C
38M
12bit/4ch DAC
12M
18M
32M
BO
OT
[5]
32M
32BT
8bit/16ch ADC
31BU12BU
18M SW
BATT CHK
MOTION SENSOR
Bypass capacitors for OMAP
32M
BO
OT
[1]
FLDM
OMAP 1.8V_block:white
OMAP 3.2V_block:blue
/WP internal Pull-Up
OMAP
32
M
32M
32M
32M
I2C
CK
I2C
DT
50
A
50
A
EX
TM
IC_
SW
18M
18
M
18M
EX
TS
PD
ET
ENC3
ENC2
ENC1
ENC0
50
C
50C
KE
Y_
INT
KEY_INT
/KE
YI4
/KE
YI3
/KE
YI2
/KE
YI1
/KE
YI0
SDET
32
BT
AN
TC
HK
FE
M_
AL
MF
EM
_P
WR
AN
TC
HK
FE
M_
PW
R
FE
M_
AL
M
CP
Z
TX
C
EX
TM
_M
EXTM_M
/SA
VE
32C
AS
TS
W
VOL
VOL
I2CCK
I2CDT
DCR_DDO
/CIN
T
CP
SBC
CVAS
SIS
T
VC
O_
MO
D
38M
SBC
SBC
12M
BATT
/ADC_INT
LE
D_
B
DA
TA
[0]
DB
[7]
DB
[6]
DB
[5]
DB
[4]
DB
[3]
DB
[2]
DB
[1]
DB
[0]
WR
0_
/WR
LC
D_
A0
LC
D_
/CS
DB
[6]
DB
[4]
DB
[2]
DB
[0]
WR
0_
/WR
LC
D_
A0
DB
[7]
DB
[5]
DB
[3]
DB
[1]
WR
1_
/OE
LC
D_
/CS
ME
LE
D_G
LE
D_R
LE
D_B
ENC2
ENC1ENC3
ENC0
LE
D_
GL
ED
_R
LB
C_
R
PLL_CLK_1
PLL_CLK_1
BT_CLK
18BT
/AP
CS
W
TH
P
AN
TS
W
/EM
G
/CINT
/PSW
/SIDE2
/EMG
EXTMIC_SW
APCSW2_0
LBC_G
FL
DM
LB
C_
BL
BC
_G
LC
D_
BL
C
WR
1_
/OE
KE
YO
1K
EY
O2
KE
YO
3
/WR
AD
D[2
3]
DA
TA
[4]
KE
YO
0
DA
TA
[5]
/OE
/CS
4
DA
TA
[1]
DA
TA
[3]
LC
D_
RS
T
DA
TA
[7]
DA
TA
[2]
DA
TA
[6]
AP
CS
W2
GP
S_
PA
_E
N
GP
S_
PA
_E
N
CTS2
18
BT
_A
FS
YN
C
18B
T_
RX
18B
T_
TX
18B
T_
AIN
18
BT
_A
CL
K
18B
T_
AO
UT
18B
T_
RT
S
18B
T_
CT
S
TXD2
RXD2
BT_AUD_DO
BT_AUD_DI
RTS2
12BU
12BU
/BT
_S
HU
TD
OW
N
/BT
_S
HU
TD
OW
N
BT_CLK
BC
LK
WC
LK
BT
_A
UD
_D
OB
T_
AU
D_D
I
CT
S2
RT
S2
TX
D2
RX
D2
18
BT
_T
X
18
BT
_R
X
18
BT
_C
TS
18
BT
_R
TS
18
BT
_A
OU
T
18
BT
_A
IN
18
BT
_A
FS
YN
C
18B
T_
AC
LK
DCR_DI
DCR_DDO
CODEC_DO
DCR_DO
/TX
D1
_JK
_E
N
/SID
E2
/SID
E1
/IN
T_
PT
T
USB_VBUS
USB0_DM
USB0_DP
USB_SW
USB_SW
RTS1
/TX
D1_JK
_E
N
5VC
PFKEY
RX
D1
5V
C
EX
TS
PD
ET
TX
D1
/OP
TD
ET
/EX
T_
PT
T
AGCKEEP
/DCR_RST
VC
O_
MO
D
/SIDE1
/RST
VE
R2
GP
SB
T_
DE
T
VE
R1
OP
CN
_T
YP
/DSW
TXC
DCR_ADI
/DCR_ACS
/DCR_CS
BCLK
VO
L
SD
ET
TH
PT
EM
P
BA
TT
Ra
mp
_O
ffse
t
CV
/ADC_INT
SDI0SDO0SCK0/ADC
19.2
M
WC
LK
CO
DE
C_
DO
BC
LK
CO
DE
C_
DI
INTM_M_CDC
RX
CP
Z
DCR_DO
DCR_DI
DCR_ACLK
/BT
_S
HU
TD
OW
N
KEYO0
/DCR_RST
AP
C
/ADC
/WR
/OE
AS
SIS
T
/DCR_DCS
PLD
/KEYI1
/KEYI3
/KEYI4
/KEYI0
KEYO3
KEYO2
/KEYI2
AGCKEEP
DD
R_R
AS
/IN
T_P
TT
LC
D_B
LC
PLD
32M_1_1
32
M_
1_
1
32
M_
1
18M_2_2
18M_2_1
18
M_
2_
2
18
M_
2_
1
12
M_
1_
1
12
M_
1_
2
18
M_
2
18M_1_1
18
M_
1_
1
18
M_
1
12M
_1_2
12M_1_2
12M
_1_1
12
M_
1
SD
O1
/DACCS
SC
K1
RX
TX
/APCSW_0
USB_VBUS_0
ANTSW_0
ANTSWUSB_VBUS
/APCSWAPCSW2
/DA
CC
S
32M_1
/FR
ST
USB_DET
BCLK
PLL0_VDDA
PLL1_VDDA
32M_1_1
18M_1_1
32M_1_1
18M
_1_1
18M_2
18M_1
PLL1_VDDA
PLL0_VDDA
12M_1
/DS
W
Ra
mp
_O
ffse
t
DD
R_A
[1]
DD
R_D
[3]
DA
TA
[6]
USB0_DM
AD
D[5
]
AD
D[1
3]
DD
R_
D[7
]
DD
R_
D[1
2]
AD
D[2
0]
DD
R_
CK
E
AD
D[7
]
DA
TA
[12
]
DD
R_D
[11]
DD
R_A
[5]
DD
R_D
QS
[0]
DD
R_A
[4]
DA
TA
[9]
DD
R_D
[15]
DD
R_
A[8
]
SCK1
TXD1
AD
D[1
6]
DD
R_D
[2]
MO
DE
L
AD
D[0
]
/CS
3
DA
TA
[11
]
AD
D[3
]
DD
R_
A[3
]
DD
R_
A[7
]
/EXT_PTT
/CS
_F
DD
R_
CS
DD
R_
A[4
]
AD
D[6
]
AD
D[8
]
DD
R_
D[5
]
AD
D[1
0]
DD
R_C
AS
DA
TA
[8]
AD
D[1
]
DA
TA
[3]
DD
R_
DQ
S[1
]
/OE
DD
R_D
[9]
DA
TA
[7]
AD
D[1
8]
DA
TA
[10
]
DD
R_A
[0]
AD
D[1
9]
DD
R_
A[2
]
AD
D[1
4]
TE
MP
AD
D[9
]
DD
R_
D[9
]
DD
R_A
[8]
DD
R_C
S
AP
C
DD
R_D
[13]
LBC_B
AD
D[1
4]
DA
TA
[13
]
DD
R_D
[6]
DD
R_D
[14]
AD
D[4
]
DA
TA
[14
]
DD
R_A
[3]
DA
TA
[0]
DD
R_W
E
AD
D[2
2]
DD
R_A
[11]
/DCR_CS
DD
R_
D[6
]
DCR_ADI
DA
TA
[14
]
DD
R_D
[5]
DD
R_
D[0
]
DD
R_D
QS
[1]
DA
TA
[15
]
AD
D[1
8]
DD
R_
D[1
5]
FC
NT
DD
R_A
[2]
AD
D[1
1]
DA
TA
[3]
LBC_R
DD
R_D
[10]
/DCR_DCS
AD
D[1
6]
DA
TA
[0]
DD
R_A
[7]
SDO1
DA
TA
[6]
DCR_ACLK
DD
R_D
[8]
I2CDT
/CS
_F
AD
D[2
]
DA
TA
[1]
CODEC_DI
/DCR_ACS
FC
NT
DD
R_
CA
S
AD
D[1
2]
DD
R_
A[1
]
DA
TA
[10
]
I2CCK
KEYO1
DD
R_
DQ
M[0
]
DD
R_
BA
[1]
DD
R_A
[9]
SCK0
DA
TA
[11
]D
DR
_D
[4]
AD
D[2
]
DD
R_C
LK
P
/FRST
/WP
AD
D[1
5]
/WP
AD
D[1
0]
DD
R_D
QM
[0]
/OPTDET
RXD1
DD
R_
D[1
0]
DD
R_A
[6]
AD
D[1
9]
DA
TA
[1]
DD
R_B
A[0
]
/SA
VE
DD
R_D
QM
[1]
AD
D[1
7]
DD
R_
A[0
]
DA
TA
[2]
DD
R_
BA
[0]
DD
R_
D[3
]
DD
R_
A[5
]
DA
TA
[4]
DD
R_
A[6
]
DD
R_D
[1]
TX
DD
R_D
[0]
DD
R_C
LK
N
/PSW
DD
R_
DQ
M[1
]
/WR
DD
R_
CL
KN
AD
D[4
]
DA
TA
[2]
AD
D[1
]
DA
TA
[12
]
AD
D[7
]
DD
R_A
[12]
DD
R_
D[1
4]
DD
R_
A[1
3]
DA
TA
[5]
DD
R_D
[7]
DA
TA
[7]
DA
TA
[8]
VBUS
SB
C
AD
D[8
]
DD
R_B
A[1
]
DD
R_
D[8
]
AD
D[1
5]
USB0_DP
DD
R_
A[9
]
AD
D[2
1]
LCD_RST
DD
R_
CL
KP
/BINT
AD
D[2
1]
AD
D[2
3]
SYMTIM_IN
AD
D[9
]
DD
R_
D[1
]
/CS
4
DD
R_
D[2
]
DA
TA
[5]
DA
TA
[4]
DD
R_
A[1
0]
DD
R_
D[1
1]
/BINT
DA
TA
[13
]
DD
R_A
[13]
DD
R_
A[1
1]
SDO0
DD
R_
WE
SYMTIM_IN
AD
D[1
2]
DD
R_
RA
S
DD
R_
DQ
S[0
]
DD
R_D
[12]
AD
D[2
3]
/RS
T
AD
D[6
]
AD
D[2
2]
AD
D[1
7]
MCLK
AD
D[3
]
AD
D[0
]
DD
R_C
KE
DD
R_
A[1
2]
DD
R_
D[1
3]
DD
R_A
[10]
DA
TA
[15
]
SDI0
AD
D[2
0]
DA
TA
[9]
AS
TS
W
AD
D[1
3]
DD
R_D
[4]
AD
D[1
1]
AD
D[5
]
OSCGNDB
RTCGNDG
RTCGNDG
OSCGNDB
Side2
EMG
Side1
PTT
G0B-0005-00*CN354
*CN353
L41-3378-0833nL138
5TLR79Z0DC22NJL210
LB73H0AV-002
L417
LB73H0AV-002L635
$C
25
4
0
R2281000pC237
AVRM10120MAABD655
1
R52
$C
60
5
25
4.7
u
C6
04
LR
79
Z0
CA
68
NJ
68
n
L2
18
E2D-0022-00CN203
10
0
R6
02
10
0
R6
01
CN652
LR
79
G0
CQ
R1
8G
18
0n
L3
05
3p
C3
07
100k
R415
10
k
R4
11
LTC044EEBFS8Q402
1SS400SM
D4071SS400SM
D4061SS400SM
D4051SS400SM
D4041SS400SM
D403
0
R220
18
0
R1
92
18
0
R1
93
$R
19
1
33
R194
0
R195
$L
35
5
27
n*L
35
4
L41-8265-538.2n
L222
L41-6865-536.8n
L223
1u
C3
04
$R221
(G)
27
p
C2
52
1000pC260
0R271
0R273
0R272
0*R359
0*R369
$R
36
8
$R
37
0
56
n
L2
21
0R270
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720CQ-0313ACN1
CN623
47k
*R367
1k
*R366
10
00
p
*C3
85
10
00
p*C
37
9
4p*C354
220*R363
220*R362
1k
*R3
65
1k
*R3
64
10
00
p*C
37
8
10
00
p
*C3
77
10
00
p
*C3
76
470k
R48
47
0k
R4
9
0
R139
0
R1
16
0
R1
37
(D)270k
R30
0
R3
1
E1B-0020-00J652
E1B-0019-00J651
0.1
u
C1
08
470k
R140
470k
R141
VT
6M
1
Q1
03
LB73H0AY-004L112
VT6M1Q114
47
0k
R1
23
47k
R124
47
0k
R1
20
5.6
k
R1
43
SM
V1
25
1-0
79
LF
D1
31
SMV1801-079LFD134
D1
32
SM
V1
80
1-0
79
LF
D1
33
SMV1801-079LFD135
SM
V1
13
0-0
79
LF
D1
36
Q1
31
MC
H3
91
4-H
/8/
CS
77
AB
E1
D1
00
M2
01
0u
C1
22
15
0R
14
2
$C
14
3
0R132
L41-2785-53270n
L131
47
0p
C1
42
47
0p
C1
47
0
R135
1000pC133
LB
73
H0
AY
-00
4
L1
41
RN(D)10R134
RN
(D)
15
0R
13
3
1000p
C134LB73H0AY-004L121
470p
C1
35
(D)390
R128
LB73H0AY-004L136
47
0p
C1
32
47
0p
C1
45
0
R127
18
0
R1
45
0
R126
$C
13
1
15
0
R1
30 0.5p
C144
CK
73
FB
B1
H1
54
K0
.15
uC
12
1
0.7
5p
C1
38
0.0
47
u
C1
23
3p
C1
37
9p
C141
L4
1-2
78
5-5
3
27
0n
L1
427p
C1
40
L41-2785-53
270nL139
L4
1-2
78
5-5
3
27
0n
L1
37
L4
1-2
78
5-5
3
27
0n
L1
32
L4
1-2
78
5-5
3
27
0n
L1
40
L4
1-2
78
5-5
3
27
0n
L1
35
Q1512SC5108FT/Y/
(B)
8p
C1
39
10
0k
R1
31
LK
73
H0
AM
47
NJ
47
nL
14
310
k
R1
36
6p
C146
RN142SD205
(G)
47
pC
20
6
(G)
22
pC
20
7
$C
25
6
(G)
12
pC
20
2
3TLR79Z0DD12N2J
L220
4TLR79Z0DC16N7J
L219
15
0p
C2
38
(B)
10
pC
22
6
(B)
2p
C2
03
LR
79
G0
CQ
56
NG
56
nL
30
7
DAN222
D8
120kR105F1B-0095-00
E10110M
R108
(B)4pC183
LB73H0AV-002L13
0.2
2u
C5
1
0.2
2u
C5
3
10
0k
R1
07
47
0p
C1
821
00
k
R1
10
LK
73
H0
AM
56
NJ
56
nL
18
11
50
R1
84
47
0p
C1
81
4.7
kR
18
3
8.2
kR
18
2
Q1812SC5108FT/Y/
501uC105
1k
R1
04
CN101
10
k
R1
21
10
k
R1
29
47
0p
C1
11
1kR112
3.3
uC
46
1000p
C195
3.3
uC
47
22
R1
81
L41-1502-7015uL12
10
R106
$C
45
SW
6
NC
5
FB
4EN3
VIN2
GND1
TPS61041DRVRIC13
47
0k
R4
4
EM6M2Q102
CK
73
FX
R1
E4
75
K4
.7u
C4
8
V+
5
oUT
4IN-3
V-2
IN+1
OPA170AIDRLRIC101
ED
ZV
8.2
BD
10
2
CK
73
0JM
1H
68
4K
0.6
8u
C5
0
Q1132SD2654/W/
RB561VM-40D10
10
4.7
u
C1
12
4.7
k
R1
11
0
R1
25
CN191470p
C197
47
k
R1
13
STBY3
GND
2
VIN4 VoUT 1
IC14
68
0p
C5
2
47
R1
09
68
0p
C4
9
0.1u
C106
33
k
R4
5
100pC104
(H0AM)
27nL191
(B)
6pC1
94
22
R46
(B)2.5pC193
10
0p
C1
07
(B)
6pC1
91
(H0AM)
27nL192
(G)
12
pC1
92
(B)2.5pC198
VDD
5
oUT
4IN-3
VSS2
IN+1
BU7295HFVIC102
22
k
R1
03
R92-3774-0527
R43R92-3774-05
27
R42
1S
S4
00
SM
D1
11
0.0
1u
C1
02
33pC103
0
R102
$R
10
1
$Q101
$C
10
1
$D
10
1
6.8
k
R1
22
10
0k
R2
68
1k
R2
69
10kR433
10
9
8
7
6
5
4
3
2
1
DVDD3318_C10
R4
DVDD3318_C9
P12
DVDD3318_C8
P6
DVDD3318_C7
P5
DVDD3318_C6N13
DVDD3318_C5M13
DVDD3318_C4L13
DVDD3318_C3L4
DVDD3318_C2K13
DVDD3318_C1J5
DVDD3318_B11K15
DVDD3318_B10J14
DVDD3318_B9G9
DVDD3318_B8F13
DVDD3318_B7F12
DVDD3318_B6F11
DVDD3318_B5F10
DVDD3318_B4F8
DVDD3318_B3F7
DVDD3318_B2F6
DVDD3318_B1E14
DVDD3318_A6H5
DVDD3318_A5G15
DVDD3318_A4G14
DVDD3318_A3G5
DVDD3318_A2F15
DVDD3318_A1F5
DV
DD
18_10
R13
DV
DD
18_9
P13
DV
DD
18_8
L6
DV
DD
18_7
K5
DV
DD
18_6
J13
DV
DD
18_5
G12
DV
DD
18_4
G11
DV
DD
18_3
G10
DV
DD
18_2
G6
DV
DD
18_1
F14
RV
DD
3
N7
RV
DD
2
H14
RV
DD
1
E5
CV
DD
18
N8
CV
DD
17
M9
CV
DD
16
M8
CV
DD
15
L12
CV
DD
14
K12
CV
DD
13
K6
CV
DD
12
J12
CV
DD
11
J6
CV
DD
10
H13
CV
DD
9
H12
CV
DD
8
H11
CV
DD
7
H10
CV
DD
6
H7
CV
DD
5
H6
CV
DD
4
G13
CV
DD
3
G8
CV
DD
2
G7
CV
DD
1
E15
NC3
M3
RSV2
T19
SATA_VDD4
N4
SATA_VDD3
P2
SATA_VDD2 P1
SATA_VDD1 M2
SATA_VDDR P3
USB_CVDD M12
USB1_VDDA18 P14
USB1_VDDA33 P15
USB0_VDDA18 N14
USB0_VDDA33 N18
DDR_DVDD18_10 R9
DDR_DVDD18_9 R8
DDR_DVDD18_8 R7
DDR_DVDD18_7 P10
DDR_DVDD18_6 P9
DDR_DVDD18_5 P8
DDR_DVDD18_4 P7
DDR_DVDD18_3 N10
DDR_DVDD18_2 N9
DDR_DVDD18_1 N6
DDR_VREF R6
DDR_ZP
U12
RTC_CVDD
L14
PLL1_VDDA
N15
PLL0_VDDA
L15
VS
S3
0
P11
VS
S2
9
N12
VS
S2
8
N11
VS
S2
7
N5
VS
S2
6
M11
VS
S2
5
M10
VS
S2
4
M7
VS
S2
3
M6
VS
S2
2
M5
VS
S2
1
M4
VS
S2
0
L11
VS
S1
9
L10
VS
S1
8
L9
VS
S1
7
L8
VS
S1
6
L7
VS
S1
5
L5
VS
S1
4
K11
VS
S1
3
K10
VS
S1
2
K9
VS
S1
1
K8
VS
S1
0
K7
VS
S9
J11
VS
S8
J10
VS
S7
J9
VS
S6
J8
VS
S5
J7
VS
S4
H15
VS
S3
H9
VS
S2
H8
VS
S1
A19
NC
2
N16
NC
1
M14
SA
TA
_V
SS
6
M1
SA
TA
_V
SS
5
L3
SA
TA
_V
SS
4
K2
SA
TA
_V
SS
3
K1
SA
TA
_V
SS
2
H2
SA
TA
_V
SS
1
H1
RT
C_
VS
S
H18
PL
L1
_V
SS
A
M15
PL
L0
_V
SS
A
M17
oS
CV
SS
L18
PRU1_R30<0>/PRU1_R31<1>
K4
MMCSD1_DAT<1>/PRU1_R30<1>/PRU1_R31<2>
J3
MMCSD1_DAT<2>/PRU1_R30<2>/PRU1_R31<3>
K3
MMCSD1_DAT<3>/PRU1_R30<3>/PRU1_R31<4>
H3
RMII_CRS_DV/PRU1_R31<29>
W19
RMII_MHZ_50_CLK/PRU0_R31<23>
W18
RMII_RXER/PRU0_R31<24>W17
RMII_RXD<0>/PRU0_R31<25>V17
RMII_RXD<1>/PRU0_R31<26>W16
RMII_TXEN/PRU0_R31<27>R14
RMII_TXD<0>/PRU0_R31<28>V16
RMII_TXD<1>/PRU0_R31<29>U18
GP6<5>P17
PRU0_R30<9>/PRU0_R31<9>R15
PRU0_R30<10>/PRU0_R31<10>R19
PRU0_R30<11>/PRU0_R31<11>R18
PRU0_R30<12>/PRU0_R31<12>T16
PRU0_R30<13>/PRU0_R31<13>U19
PRU0_R30<14>/PRU0_R31<14>V19
PRU0_R30<15>/PRU0_R31<15>V18
GP6<6>V15
GP6<7>W14
SATA_REGN3
SATA_REFCLKNN1
SATA_REFCLKPN2
SATA_TXNJ2
SATA_TXPJ1
SATA_RXNL2
SATA_RXPL1
LCD_AC_ENB_CSR5
MMCSD1_DAT<4>/LCD_VSYNCG4
MMCSD1_DAT<5>/LCD_HSYNCH4
MMCSD1_DAT<6>/LCD_MCLKF2
MMCSD1_DAT<7>/LCD_PCLKF1
MMCSD0_CLKE9
USB1_DPP19
USB1_DMP18
USB0_VDDA12N17
USB0_DRVVBUSK18
USB0_VBUSN19
USB0_IDP16
USB0_DPM19
USB0_DMM18
RTC_ALARM/DEEPSLEEPF4
RTC_XoH19
RTC_XIJ19
oSCoUTK19
oSCINL19
CLKoUTT18
RTCK/GP8<0>K17
EMU1K16
EMU0J16
TRSTL17
TCKJ15
TDoJ18
TDIM16
TMS
L16
RESEToUT
T17
NMI
J17
RESET
K14
LC
D_D
<0>
W1
LC
D_D
<1>
W2
LC
D_D
<2>
W3
LC
D_D
<3>
V1
LC
D_D
<4>
V2
LC
D_D
<5>
V3
LC
D_D
<6>
U1
LC
D_D
<7>
U2
LC
D_D
<8>
/BooT
<0>
U3
LC
D_D
<9>
/BooT
<1>
T1
LC
D_D
<10>
/BooT
<2>
T2
LC
D_D
<11>
/BooT
<3>
T3
LC
D_D
<12>
/BooT
<4>
R1
LC
D_D
<13>
/BooT
<5>
R2
LC
D_D
<14>
/BooT
<6>
R3
LC
D_D
<15>
/BooT
<7>
P4
DD
R_D
QG
AT
E1
R12
DD
R_D
QG
AT
E0
R11
DD
R_B
A<
0>
V8
DD
R_B
A<
1>
T9
DD
R_B
A<
2>
U8
DD
R_D
QS
<1>
V11
DD
R_D
QS
<0>
T14
DD
R_D
QM
<1>
R10
DD
R_D
QM
<0>
W13
DD
R_C
S
V9
DD
R_C
AS
U9
DD
R_R
AS
W9
DD
R_W
E
T8
DD
R_C
KE
V7
DD
R_C
LK
N
W7
DD
R_C
LK
P
W8
DD
R_A
<0>
U7
DD
R_A
<1>
T7
DD
R_A
<2>
W6
DD
R_A
<3>
V6
DD
R_A
<4>
U5
DD
R_A
<5>
V5
DD
R_A
<6>
W5
DD
R_A
<7>
U6
DD
R_A
<8>
U4
DD
R_A
<9>
T6
DD
R_A
<10>
W4
DD
R_A
<11>
T4
DD
R_A
<12>
V4
DD
R_A
<13>
T5
DD
R_D
<0>
U15
DD
R_D
<1>
U14
DD
R_D
<2>
V14
DD
R_D
<3>
U13
DD
R_D
<4>
V13
DD
R_D
<5>
V12
DD
R_D
<6>
W12
DD
R_D
<7>
W11
DD
R_D
<8>
T13
DD
R_D
<9>
T11
DD
R_D
<10>
T10
DD
R_D
<11>
T12
DD
R_D
<12>
U10
DD
R_D
<13>
V10
DD
R_D
<14>
U11
DD
R_D
<15>
W10
AMUTE/UART2_RTS D5
AFSR C2
ACLKR A1
AHCLKR/UART1_RTS A2
AFSX B2
ACLKX B1
AHCLKX/USB_REFCLKIN/UART1_CTS A3
AXR0/ECAP0_APWM0/MII_TXD<0>/CLKS0 F3
AXR1/DX0/MII_TXD<1> E1
AXR2/DR0/MII_TXD<2> E2
AXR3/FSX0/MII_TXD<3> E3
AXR4/FSR0/MII_CoL D1
AXR5/CLKX0/MII_TXCLK D3
AXR6/CLKR0/MII_TXEN C1
AXR7 D2
AXR8/CLKS1/ECAP1_APWM1 E4
AXR9/DX1 C3
AXR10/DR1 D4
AXR11/FSX1 C5
AXR12/FSR1 C4
AXR13/CLKX1 B3
AXR14/CLKR1 B4
AXR15/ECAP2_APWM2 A4
GP8<12> G3
MMCSD1_CMD J4
MMCSD1_CLK G2
MMCSD1_DAT<0> G1
GP6<8> T15
GP6<9> U16
GP6<10> W15
GP6<11> U17
GP6<12> R16
GP6<13> R17
SPI1_SoMI H17
SPI1_SIMo G17
SPI1_SCS<7>/I2C0_SCL
G16
SPI1_SCS<6>/I2C0_SDA
G18
SPI1_SCS<5>/UART2_RXD
F17
SPI1_SCS<4>/UART2_TXD
F16
SPI1_SCS<3>/UART1_RXD
E18
SPI1_SCS<2>/UART1_TXD
F19
SPI1_SCS<1>F18
SPI1_SCS<0> E19
SPI1_ENA H16
SPI1_CLK G19
SPI0_SoMI/MII_RXER C16
SPI0_SIMo/MII_CRS C18
SPI0_SCS<5>/UART0_RXD/MII_RXD<3> C19
SPI0_SCS<4>/UART0_TXD/MII_RXD<2> D18
SPI0_SCS<3>/UART0_CTS/MII_RXD<1> E17
SPI0_SCS<2>/UART0_RTS/MII_RXD<0> D16
SPI0_SCS<1>/MDIo_CLK E16
SPI0_SCS<0>/MDIo_D D17
SPI0_ENA/MII_RXDV C17
SPI0_CLK/MII_RXCLK D19
EM
A_
WA
IT<
1>
B19
EM
A_
WA
IT<
0>
B18
EM
A_
oE
B15
EM
A_
WE
N_
DQ
M<
0>
C8
EM
A_
WE
N_
DQ
M<
1>
A5
EM
A_
WE
B9
EM
A_
A_
RW
D10
EM
A_
CS
<5
>
B16
EM
A_
CS
<4
>
F9
EM
A_
CS
<3
>
A17
EM
A_
CS
<2
>
B17
EM
A_
CS
<0
>
A18
EM
A_
CA
S
A9
EM
A_
RA
S
A16
EM
A_
SD
CK
E
D8
EM
A_
CL
K
B7
EM
A_
BA
<1
>
A15
EM
A_
BA
<0
>
C15
EM
A_
A<
0>
C14
EM
A_
A<
1>
D15
EM
A_
A<
2>
B14
EM
A_
A<
3>
D14
EM
A_
A<
4>
A14
EM
A_
A<
5>
C13
EM
A_
A<
6>
E13
EM
A_
A<
7>
B13
EM
A_
A<
8>
A13
EM
A_
A<
9>
D12
EM
A_
A<
10
>
C12
EM
A_
A<
11
>
B12
EM
A_
A<
12
>
D13
EM
A_
A<
13
>
D11
EM
A_
A<
14
>/M
MC
SD
0_
DA
T<
7>
A12
EM
A_
A<
15
>/M
MC
SD
0_
DA
T<
6>
C11
EM
A_
A<
16
>/M
MC
SD
0_
DA
T<
5>
E12
EM
A_
A<
17
>/M
MC
SD
0_
DA
T<
4>
B11
EM
A_
A<
18
>/M
MC
SD
0_
DA
T<
3>
E11
EM
A_
A<
19
>/M
MC
SD
0_
DA
T<
2>
C10
EM
A_
A<
20
>/M
MC
SD
0_
DA
T<
1>
A11
EM
A_
A<
21
>/M
MC
SD
0_
DA
T<
0>
B10
EM
A_
A<
22
>/M
MC
SD
0_
CM
D
A10
EM
A_
D<
0>
C9
EM
A_
D<
1>
A8
EM
A_
D<
2>
B8
EM
A_
D<
3>
E8
EM
A_
D<
4>
B5
EM
A_
D<
5>
E7
EM
A_
D<
6>
C6
EM
A_
D<
7>
D7
EM
A_
D<
8>
E10
EM
A_
D<
9>
D9
EM
A_
D<
10
>
A7
EM
A_
D<
11
>
D6
EM
A_
D<
12
>
A6
EM
A_
D<
13
>
B6
EM
A_
D<
14
>
C7
EM
A_
D<
15
>
E6
IC401
0.0
1u
C4
03
10
0p
C4
02
10
R4
03
NC
U1
5W
F1
04
F6
ST
H4
01
-t
0.0
1u
C4
01
1k
R4
01
VCC 4
oUT 3
GND2
VC1
L7H-0076-00
19.2MHzX401
22
R404
0.01u
C404
33
k
R4
06
15
k
R4
05
68
0
R4
08
10
R4
07
Q4012SC4617/S/
0.01u
C406
(-86)4.7u
L402
5p
C4
08
$R
40
9
LB
73
H0
AV
-00
2L
10
0.1
uC
38 0
.1u
C4
0
1k
R40
0.4
7u
C4
30.1
u
C4
2 Vo
UT
3
GN
D
2
VIN
4
Co
NT
Ro
L
1
NJM2878F4-32IC11
LB73G0AM-004*L8
1k
*R9 STBY3
GND
2
VIN4 VoUT 1
*IC7
0.4
7u
C2
6
0.4
7u
C2
5
LB73G0AM-004L7 0
.1u
C3
5
10k
R26CE3 VSS 2
VIN4 VoUT 1
IC5
0.2
2u
*C3
4
6.3
10
uC2
4
10
0k
R2
5
4.7
u
C2
3
0.2
2u
*C1
5
0.2
2u
*C1
6
LB73H0AV-002*L9
1k
*R8 STBY3 GND 2
VIN4 VoUT 1
BU18TD2WNVX*IC8
100k
R36
10
0k
R3
7
VT
6M
1
Q5
100
R35
47
0k
R2
9
47
0p
C3
0
6.3
10
uC3
2
GN
D_
3 9
GN
D_
2 8
EN7
VIN_2
6
VIN_1
5
GND_1
4
VoUT_2 3
VoUT_1 2
MoDE 1
LXDC2XQ12A-252IC2
10
0k
R3
3
10
u
C3
1
1k
R3
2
2.7
R3
8
22
u
C2
2
LB73G0AM-004
L5
2.2u
L4
(D)
68
kR2
3
(D)
18
kR2
2
0.1
u
C2
1
33
00
pC
20
PG
4
SW
33
SW
22
SW
11
PGND2
16
PGND115
VoS14
EN13
PV
IN2
12
PV
IN1
11
AV
IN10
SS
/TR
9
DEF 8
FSW 7
AGND 6
FB 5
TPS62140RGT
IC3
47
0p
C3
6
NC
3
VIN
2
VS
S
4
Vo
UT
1
BATT INT
XC
61
CC
56
02
N-G
IC1
47
0p
C3
7 47
0k
R1
2
10
k
R1
3
47
0k
R1
4
EM
D1
2
Q1
10k
R15
E2D-0082-00CN10
E2D-0082-00CN8
(-7
1)
27
nL3
03
CN9
(D)
47
0k
R6
6
(D)
47
0k
R6
5
$C
27
0
E2D-0058-00CN202
E2D-0058-00CN201
RK74HB1J101JCP2
RK
74
HB
1J1
01
J
CP
41
4
LR79G0CQ8N2C
8.2nL310
470pC7
2.2k
R11
10u
C316
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720BP-0341ACN402
TO DISPLAY UNITXC1-209 A/2CN202
TO DISPLAY UNITXC1-209 B/2 CN301
22
R4
14
22
R413
0
R412
6.347u
C664
6.347uC675
G0B-0005-00*CN357
*CN356
10
00
p*C
39
2
2
1
E41-1476-05
CN602
10
0R
47
9 L4
30
47
0p
C4
70
L4
31
10
0
R4
80
47
0p
C5
10
0.1
uC
51
6
47
0p
C4
69
47
0p
C5
15
RK
74
HB
1J1
01
JC
P4
11
RK
74
HB
1J1
01
J
CP
40
8
LB
73
H0
AV
-00
2
L4
28
RK
74
HB
1J1
01
J
CP
40
9
0.1
uC
51
8
RK
74
HB
1J1
01
JC
P4
10
LB
73
H0
AV
-00
2L
42
7
47
0p
C4
71
CN
45
2
RK
74
HB
1J1
01
J
CP
41
3
L4
29
RK
74
HB
1J1
01
JC
P4
12
47
0p
C4
72
47
0p
C4
73
47
0p
C4
76
47
0p
C4
75
47
0p
C4
74
47
0p
C4
77
0.1
uC
51
7
10
0p
C6
7
RK74HB1J101JCP1
10
0p
C6
8
6
5
4
3
2
1
E40-6883-05CN7
10
0p
C7
0
10
0p
C6
9
F1B-0087-00E401
F1B-0083-00E301
F1B-0085-00E601
F10-3228-15*E351
10
00
p
C3
06
(B)
3pC3
02
10
0R
30
21
00
R3
01
RK74HB1J100JCP303
10
(CO
DE
C)
CP
60
1
100*4
CP405
100*4
CP401
10
0*4
CP
40
3
100*4
CP404
10*4
CP406
10*4CP402
RK74HB1J100JCP301
RK74HB1J100JCP302
1u*C370
L92-0487-05*L352
10
0*R
35
2
10
0*R
35
3
-32.768000k-NSA3534ANDK NZ2520BL77-3121-05*X351
0.01uC356
(-71)10n
*L353
47
k*R
36
1
0.1u
*C361
0.1u*C371
GPS_PPS_OUTCN351
0.1u*C372
2.5
p*C
39
5
L7K-0059-00
*L359
120p*C391
L92-0487-05
*L358
BT_CLK_REQ
CN355100*R351
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1
4
VCC(A) 3
VCC(B) 2
DIR2 1
74AVC4TD245GU*IC353
L92-0487-05*L366
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1
4
VCC(A) 3
VCC(B) 2
DIR2 1
74AVC4TD245GU*IC352
L92-0487-05
*L365
47p
*C382
0.1u*C384
0.1u*C381
$C
39
0
$C
35
3
10k
*R357
$C
35
2
L79-1987-05*L361
RK
74
HB
1J1
00
J*C
P3
51
RK
74
HB
1J1
00
J*C
P3
52
10p*C389
10k
*R358
0.1u
*C383
0.1u
*C380
0.1u*C386
1u*C388
0.1u*C387
VB
AT
1A
2
VD
D1P
8V
_2
A3
VD
DS
1B
3
BT
_A
UD
_C
LK
D1
BT
_A
UD
_F
SY
NC
D2
BT
_A
UD
_IN
D3
BT
_A
UD
_oU
TC
3
BT
_H
CI_
UA
RT
_T
XA
4
BT
_H
CI_
UA
RT
_R
XB
5
BT
_H
CI_
UA
RT
_C
TS
B4
BT
_H
CI_
UA
RT
_R
TS
B7
BT
_H
oS
T_W
AK
EU
PA
5
BT
FM
_n
SH
UT
DoW
NA
6
VD
D_D
IG1
E5
VS
S_
DIG
6B
6
BT
_G
PIo
<6
>H
5
BT
_G
PIo
<5
>D
7
BT
_G
PIo
<4
>C
5
BT
_G
PIo
<3
>D
6
BT
_G
PIo
<2
>C
7
BT
_T
ES
TT
PB
8
VS
S_
DP
LL_
BT
A7
VD
D_
DC
o_B
TA
8
VS
S_
DC
o_
BT
A9
VD
D_R
F_
BT
B9
BT
_T
ES
TT
MA
10
VSS_RF_BT
B1
0
BT_RF
C1
0
VDD1P8V_BT
C8
VDD_LDoIN_CLASS1P5_BT
D8
VDD_CLASS1P5_BT
D9
VDD_PPAIF_BT
D1
0
REF_CLK_LV E7
REF_CLK_HV E8
BT_WAKEUP
H1
0
VSS_REF_CLK E9
VSS_DIG3
E1
0
VDD_SRAM1 F9
VDD_DIG4
F10
VSS_DIG1 G9
VDDS2
G1
0
FM_I2C_SDA E6
FM_I2C_SCL F6
FM_IRQ G6
FM_I2S_CLK F8
FM_I2S_FSYNC F7
FM_I2S_oUT G7
FM_I2S_IN G8
FM_AUD_IN_L
H7
FM_AUD_IN_R
H8
RTC_CLK
H9
VDD1P8_FM
J8
VSS_PASYNTH_FM
J1
0
TE
ST
_E
NL
10
VS
S_
PA
_F
MJ9
FM
_R
FP
_o
UT
K9
FM
_R
FP
_IN
L9
VS
S_
RF
_F
MK
8
FM
_A
BG
AP
_C
AP
L8
VS
S_
AD
CP
LL_
FM
J7
FM
_A
UD
_o
UT
_R
K7
FM
_A
UD
_o
UT
_L
L7
RE
F_C
LK
_R
EQ
J6
VD
D_
DIG
3K
6
VP
PL6
VS
S_
DIG
4J5
VD
DS
3K
5
VD
D_
SR
AM
2L5
CLK
_R
EQ
Po
LG
4
VS
EN
SE
J4
IFoR
CE
L4
GP
S_I2
C_
UA
RT
_S
EL
H4
GP
S_P
A_
EN
G3
GP
S_E
XT
_L
NA
_E
NH
6
GP
S_IR
QG
5
VS
S_
MIX
_G
PS
K3
VD
D_
IF_
GP
SK
4V
SS
_L
NA
_G
PS
2L3
GP
S_L
NA
_IN
L2
VS
S_
LN
A_
GP
S3
K2
VSS_LNA_GPS1
L1
VDD_PLL_GPS
J2
VSS_PLL_GPS
J1
VDD1P8_GPS
J3
GPS_TP
H3
GPS_TM
H2
GPS_UART_TXF5
GPS_UART_RXE3
GPS_SENS_I2C_SCLF4
GPS_SENS_I2C_SDAE4
GPS_nSHUTDoWND5
GPS_TIMESTAMPC6
GPS_PPS_oUTC4
TCXo_LDo_INH1
VSS_DIG2F3
VDD_DIG2F2
VDD_TCXoG1
VSS_TCXo_CLKG2
TCXo_CLK_LVF1
TCXo_LDo_VPRoGE1
VDDS4E2
TCXo_CLK_REQD4
VSS_DIG5
C2
VDD_SRAM_LDo
C1
VDD_DIG_LDo
B2
VDD1P8V_1
B1
PMTEST_1P8V
A1
*IC351
1u
*C3
65
1u
*C3
64
18
p*C
36
3
$C362
0.1u*C359
0.1u*C373
39*R355
BT_TX_DBGXCN352
15
0*R
35
4
15
0*R
35
6
*Q351SSM3K15AMFV
10
k
R3
60
0.1
u*C
36
8
0.1
u*C
37
5
0.1
u
*C3
66
22p
*C369
0.1
u*C
36
7
0.1u*C358
0.1u*C360
0.1u*C374
1u*C357
L92-0487-05
*L351
10
k
R6
85
0R604
1S
S3
90
D3
03
1S
S3
90
D3
04
15p
C310
1S
S4
00
SM
D3
01
1S
S4
00
SM
D3
02
SPC10501A01
D653
D6
54
D6
52
ED
ZV
6.8
BD
65
1
CN460
CN458
CN457
CN456
CN455
0.1u
C683
47
0p
C6
93
56
0
R6
59
33
0k
R6
65
VCC
5
oUTY
4GND3
INA2
G1
TC7SET125FUFIC652
FZA10BH-R315F650
VCC
5
oUTY
4 GND 3
INA 2
INB 1
TC7SZ08FEIC654
47
0p
C6
95
0.01uC697
27
0k
R6
64
47
k
R6
58
47
kR
67
8
RE1C001UNQ656
470k
R657
Q6502SB1694
2.7
k
R6
81
27kR676
0.0
68
u
C6
71
PoUT 10
PW-GND
9
PRE-GND
8
PHASE
7
NF
6RIPPLE5
VIN4
NC23
VCC2
NC11
TA7368FGIC650
22
0p
C6
90
10
k
R6
55
Q6
52
SS
M3
K3
24
RF
Q651SSM3K324RF
47
pC
68
9
CE
6
VS
S
5
NC
2
4
Vo
UT
3
NC
1
2
VIN
1
XC6209B502D-GIC651
22
u
C6
69
10
0
R6
53
68
0
R6
68
220p
C6
79
100p
C681
2.2
u
C6
91
1u
C6
86
0.1
u
C6
92
0R672
2.2
u
C6
67
0.1
u
C6
87
22
R6
70 2.7
k
R6
84
0.1u
C673
10kR683
CN
65
0
$C
66
5
LTC044EEBFS8Q654
1u
C6
88
CN
651
220k
R682
22
0k
R6
67
100
R663
0.01u
C698
470
R680
22
0p
C6
77
RB706F-40-MCD650
LTC014EEBFS8Q653
1k
R6
61 22
0p
C6
84
1.5k
R651
10
00
p
C3
46
$C
26
8
0
R267
10
1uC3
45
CN447
0R639
0R638
CN624
10kR637
0
R636
1000pC344
0.1
u
C2
7
$D
60
8
ED
ZV
6.8
BD
62
0
0.3
3u
C6
27
1k
R6
35
10
0p
C6
58
CN
60
4
2.2
k
R6
09
4.7
uC
66
3
10
0p
C6
57
LB73G0AM-004L622
LB73G0AM-004L623
CN
60
5
101u
C606
LB73G0AM-004
L605
10u
L609
1u
C6
07
4.7
u
C6
21
10
0p
C6
17
0.1
uC
60
1
2.2
u
C6
08
2.2
uC
61
0
LB73G0AM-004L604
LB
73
G0
AM
-00
4L
61
2
XToG7
MCLK/XTIG6
CLKoUT5G5
CLKoUT2/GPIo2G4
DBVDDG3
DCVDDG2 DGND
G1IN1R
F7
VMIDC
F6
IN4R
F5 IN2
R
F4
CS
/GP
Io6
F3
AD
CD
AT
F2
BC
LK
F1
IN1L
E7
LD
oV
DD
E6
IN4L
E5
IN2L
E4
oS
CE
NA
/GP
Io5
E3
DA
CD
AT
E2
LR
CL
K
E1
AG
ND
D7
AV
DD
D6
IN3L
D5
IN3R
D4
CIFMoDE
D3
SDA
D2
SCLK D1
CPGND C7
CPVDD C6
HPoUT1L C5
HPoUT2L C4
SPKoUTLN
C3
SPKoUTRN
C2
SPKGND2
C1
CPCB
B7
CP
CA
B6
HP
oU
T1
R
B5
HP
oU
T2
R
B4
SP
Ko
UT
LP
B3
SP
Ko
UT
RP
B2
SP
KV
DD
2
B1
CP
Vo
UT
N
A7
CP
Vo
UT
P
A6
HP
oU
TF
B
A5
MIC
BIA
S
A4
MIC
VD
D
A3
SP
KV
DD
1
A2
SP
KG
ND
1
A1
IC601
4.7u
C609
4.7
u
C6
02
LB73G0AM-004
L601
2.2
u
C6
22
L610
0.0
1u
C6
26
4.7
u
C6
20
LB73G0AM-004L613
4.7
u
C6
15
4.7u
C603
$R
61
1
RB521CM-30
D609
2.2
k
R6
10
1k
R6
08
$R
60
7
$C
66
0
4.7
uC
65
9
0.3
3u
C6
25
101uC612
$C614
D6
21
470R605
10u
L608
$R606
$D
60
7
$D
60
6
10
0p
C6
18
$D
60
5
CN
31
1
CN
31
0
CN
30
9
CN
30
8
CN
30
7
CN
30
6
CN439
(B)6pC228
$C
23
1
390pC227
1k
R2
37
10
0k
R2
34
3.9
k
R2
33
ED
ZV
5.6
B
D2
04
220
R230
6.8
k
R2
10
5.6
k
R2
09
CN445
9T
L215
CN
43
7
CN
43
6
CN454
$C
41
5
$C
41
3
L79-1946-05L416
10
u
C4
30
$C
41
9
$C
41
8
L79-1946-05L415
L79-1946-05L414
$C
42
0
L79-1946-05L413
$C
41
4
$C
41
2
$C
41
1
$C
41
0
L79-1946-05L412
L79-1946-05L411
4.7
uC
43
1
10
u
C4
29
CN450
10
00
p
C3
38
CN443
18
R315
27
0
R3
16
27
0
R3
14
15p
C311
LR
79
G0
CQ
82
NG
82
nL
31
3
82
0
R3
03
82
0
R3
04
5.6R312
(B)
3p
C2
55
LR79Z0DD43N6J9T
L216
9T
L217
1000p
C213
1k
R2
05
10
00
p
C2
12
10
00
pC
21
4
CE
3VSS2
VIN
4VoUT1
XC8102AA07-GIC201
12
0R
20
4
10
00
p
C2
11
LR
73
Z0
AE
2R
2J
2.2
uL
20
3
$C
21
0
$L202
RN
14
2S
D2
03
RN
14
2S
D2
02
(G)
15
pC
20
9
LR79Z0DC45N5J9T
L201
(G)
18
p
C2
69
RN142S
D201
CN
6
CN
30
5
1000pC325
39p
C334
330R450
680R336
680R335
LK
73
H0
AM
33
NJ
33
n
L3
04
(B)
2pC3
05
10
u
C3
33
1000p
C323
0.01u
C324
1000pC330
0.1uC329
0.01u
C326
0.1uC327
1000pC328
0.1
u
C3
21
10
00
p
C3
22
0.1uC332
1000pC331
0
R3
33
1k
R332
(-7
1)
33
nL3
01
CN
42
1
CN
419
CN
40
6
CN
418
CN
40
9
CN
415
CN
413
CN
30
3
CN
40
8
CN
416
+BCN3
CN
417
CN412
CN5
CN423
CN424
CN
40
5
SB1CN4
CN
414
CN
42
2
CN453
CN
30
4
CN
40
7
CN
2
VSS1E8VSS2
H2VSS3
H7
VCCG5
NC
1
A1
NC
2
A8
RF
U1
B1
RF
U2
C1
RF
U3
D1
NC
3
H1
NC
4
H8
RY
/BY
A4
RF
U4
E1
BY
TE
F7
RF
U5
G1
DQ
15/A
-1
G7
DQ
14
F6
DQ
13
G6
DQ
12
F5
DQ
11
G4
DQ
10
F4
DQ
9
G3
DQ
8
F3
DQ
7
E6
DQ
6
H6
DQ
5
E5
DQ
4
H5
DQ
3
H4
DQ
2
E4
DQ
1
H3
DQ
0
E3
VIo
2
D8
VIo
1
F1
WP
/AC
C
B4
RE
SE
T
B5
WE
A5
oE
G2
CE
F2
A25
G8
A24
F8
A23
C8
A22
B8
A21
C5
A20
D4
A19
D5
A18
C4
A17
B3
A16
E7
A15
D7
A14
C7
A13
A7
A12
B7
A11
D6
A10
C6
A9
A6
A8
B6
A7
A3
A6
C3
A5
D3
A4
B2
A3
A2
A2
C2
A1
D2
A0
E2
IC404
VSSQ5 E1
VSSQ1 D9
VSSQ4 C1
VSSQ3 B9
VSSQ2 A3
VSS3 K1
VSS2 F1
VSS1 A1
VDDQ5E9
VDDQ4D1
VDDQ3C9
VDDQ2B1
VDDQ1A7
VDD3K9
VDD2F9
VDD1A9
A1
2
H3
NC
1
F7
NC
2
F3
UD
QS
E2
LD
QS
E8
DQ
15
A2
DQ
14
B3
DQ
13
B2
DQ
12
C3
DQ
11
C2
DQ
10
D3
DQ
9
D2
DQ
8
E3
DQ
7
E7
DQ
6
D8
DQ
5
D7
DQ
4
C8
DQ
3
C7
DQ
2
B8
DQ
1
B7
DQ
0
A8
UD
M
F2
LD
M
F8
WE
G7
CA
S
G8
RA
S
G9
BA
1
H9
BA
0
H8
CS
H7
CK
E
G1
CK
G2
CK
G3
A1
1
H2
A1
0/A
P
J7
A9
H1
A8
J3
A7
J2
A6
J1
A5
K3
A4
K2
A3
K8
A2
K7
A1
J9
A0
J8
IC402
VS
S4 53
DA_FS52
AD_FS51
AD_SDo50
AD_SCLK49
DVDD48
LD47
SDATAo46
SCLK45
SDATAI44
CSN43
AGC_KEEP42
TX_PDN41
RX_PDN40
RS
TN
39
VC
oM
_A
D
38
AD
VD
D
37
AD
VS
S
36
TE
ST
2
35
Ao
UT
_N
34
Ao
UT
_P
33
RX
VD
D
32
BIA
S1
31
LN
AV
DD
30
LN
AC
oN
T
29
LN
AIN
28
VS
S3
27
VSS2 26
LNAoUT 25
DEMVDD 24
DEMIN 23
VSS1 22
LoVDD 21
RFoUTN 20
RFoUTP 19
LoIN 18
LoDVDD 17
CPZ 16
SWIN 15
CP 14
CP
VD
D
13
SY
NV
DD
12
SY
NV
SS
11
VR
EF
2
10
TC
Xo
IN
9
VR
EF
1
8
DA
CV
DD
7
SM
Fo
UT
6
BIA
S2
5
TE
ST
1
4
DA
_S
DI
3
DV
SS
2
DA
_S
CL
K
1
AK2401
IC303
+VA232
REFP31
REFM30
GPIo29
+VBD28
BDGND27
SDo26
SDI25 SC
LK
24
CS
23
AG
ND
2
22
+V
A1
21
CH
0
20
CH
1
19
CH
2
18
CH
3
17
CH4 16
CH5 15
CH6 14
CH7 13
CH8 12
CH9 11
CH10 10
CH119
CH
12
8
CH
13
7
CH
14
6C
H15
5A
INM
4
AIN
P
3
MX
o
2
AG
ND
1
1
ADS7961SRHBIC409
SD
A1
0
SCL 9
ADD 8
INT 7
RSVD 6
VD
D5
GND4
DNC23
DNC12
IoVDD1
KXCJ9-1008IC406
SCLK
10
SYNC9
DIN8
VREFIN7
GND6 VoUTD
5
VoUTC
4
VoUTB
3
VoUTA
2
VA
1
DAC124S085CIS
IC410
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7442NUXIC18
VCC
8
oUT2
7
-IN2
6
+IN2
5VEE4
+IN13
-IN12
oUT11
BA3472FVM
IC203
CE
6
VS
S
5
NC
2
4
Vo
UT
3
NC
1
2
VIN
1
XC6209B502D-GIC6
CE
6
VS
S
5
NC
2
4
Vo
UT
3
NC
1
2
VIN
1
XC6209B502D-GIC17
CE
6
VS
S
5
NC
2
4
Vo
UT
3
NC
1
2
VIN
1
XC
62
09
B3
12
D-G
IC9
CUR_ADJ
6
ENABLE
5
RF_OUT
4RF_IN3
NC2
VCC1
Pre-DRIVE
BGU6104IC202
CE
6
VS
S
5
NC
2
4
Vo
UT
3
NC
1
2
VIN
1
XC6209B502D-GIC15
VCC
5
oUTY
4GND3
INA2
INB1
TC7SZ08FE
IC405
VD
D
3
DS
2
oU
T
4
VS
S
1
S-80135ANPF-GIC403
Vo
UT
3
VS
S
2
VIN
4
CE
1XC
62
15
B1
22
N-G
IC1
0
VoUT
3EN2
GND
4VIN1
LXDC2HN18F163IC4
CE
3 VSS 2
VIN
4 VoUT 1
XC8102AA07-GIC12
SSM6N15AFEMQ2
SSM6N15AFEM
Q3
SSM3K15AMFVQ205
Q206SSM3K15AMFV
RK73PB2H1R2J
1.2
R656
47
0k
R1
64
70
kR
17
47
kR
41
47
kR
34
4.7
kR
44
2
4.7
kR
44
9
4.7k
R445
22k
R431
$R
41
8
2.2
kR
42
5
2.2
k
R4
47
2.2
k
R4
48
2.2
k*R
41
9
22
R4
28
100k
R18
100kR444
100kR19
100kR20
10
0k
R4
7
100kR21
100k
R443
10kR434
10kR432
10
kR
24
9
1M
R4
35
2.2
kR
42
1
$R
41
7
1k
R3
9
$R
41
6
1k
R4
26
1k
R24
2.2
k
R4
41
1k
R429
10
0R
46
9
10
0R
47
0
(D)
6.8
k
R2
64
(D)
6.8
k
R2
56
(D)
47
k
R5
0
(D)
47
kR5
1
(D)4.7kR252
(D)4.7kR253
(D)
39
k
R2
55
(D)
22
kR
58
(D)
18
kR
57
(D)
18
0k
R1
0
$R
20
3
(D)100k
R463
(D)10k
R464
1k
R4
39
1k
R4
40
10
kR
21
4
8.2k
R617
68
kR
65
0
(D)
47
kR
32
5
47
k
R2
45
47kR246
0
R331
10
R2
19
47
0
R6
0 3.3
kR
56
47
R2
47
22
0
R2
57
27
0
R3
10
3.3
k
R2
15
3.3
k
R2
22
3.3kR258
10
0
R2
18
18R207
27
0k
R2
7
(D)
27
k
R3
30
27k
R244
18
0
R2
01
18
0
R2
02
27
R2
51
22
0k
R2
8
3.9
k
R2
60
10
k
R6
52
2.2
kR
42
0
2.2
kR
42
4
2.2
kR
42
7
2.2
kR
42
32
.2k
R4
22
22
R4
10
22R211
27
0
R2
06
27
0
R2
08
33R223
8.2k
R259
(D)
39
kR
26
5
12
0
R2
13
$R459
$R460
1k
R212
47
R2
16
10
0R
46
7
100
R313
10
0R
46
8
10
R446
0
R7
$R
6
0
R466
0R462
0
R461
0
R402
0
R436
*R1
0
R430
0
R437
49.9
R438
82
k
R2
27
47
0
R6
54
0
R452
0
R59
0
R4
51
FINAL
Q202RD07MUS2BT514
DRIVE
Q201RD01MUS2BT513
RB521CM-30D402
RB521CM-30D401
RB520SM-30D9
1/3
0.2
2R2
48 1/3
0.2
2R2
50
LTC044EEBFS8Q204
LTC014EEBFS8Q6
Q203LSCR523EBFS8
6T
LR
79
Z0
DC
27
N9
JL
21
3
(-7
1)
27
0n
L2
06
LK73H0AM56NJ56n
L209
LB73H0AV-002L401
LB73H0AV-002L11
LB
73
F0
AW
-00
2L
21
1
L404
LB73G0AM-004L3
LB73G0AM-004
L410
LB73G0AM-004L6
L407
$L
40
3
L408
LB
73
G0
AM
-00
4
L4
09
LB73F0AW-002L1
LB
73
F0
AW
-00
2L
21
4
L406
L405
L77-1802-05X402
LR
79
G0
CQ
R1
5G
15
0n
L3
12
LR
79
G0
CQ
R2
2G
22
0n
L3
11
LR79G0CQ82NG
82nL309
LR
79
G0
CQ
82
NG
82
nL
31
4
LR
79
G0
CQ
R3
3G
33
0n
L3
15
LR
79
G0
CQ
47
NG
47
nL
30
2
LR
79
G0
CQ
47
NG
47
nL
30
8
FZA10BQ-3R15
F1
FZA10BH-R50F2
10
0k
NC
U1
5W
F1
04
F6
S
TH
20
1
-t
EMD12Q207
VT6M1
Q4
6800pC9
68
00
p
C3
47
00
pC
22
2 10
00
pC
25
7
47
0p
C6
6
10
00
p
C2
61
1000pC263
10
00
p
C2
24
47
0p
C1
7
10
00
p
C5
6
82
00
p
C2
64
82
00
p
C2
65
1000p
C313
10
00
pC
1
0.0
1u
C4
53
0.01u
C314
0.0
1u
C4
48
$C
49
5
0.0
1u
C3
03
$C
49
4
0.0
47
u
C2
21
0.22u
C424
$C
24
3
0.1uC454
0.1uC44
0.2
2u
*C3
3
1u
C4
52
1u
C4
45
1u
C501
0.1
u
C4
1
1u
C4
96
0.4
7u
C3
43
2.2
u
C3
01
10
uC
34
2
2.2
uC
55
1u
C6
74
2.2
u
C2
9
2.2
uC
60
1uC315
25
1uC
39
0.1
u
C6
72
0.1
uC
54
0.0
56
uC
26
2
$C
41
6
4.7
uC
43
3
10
uC
43
2 $C
41
7
10
u
C4
36
25
4.7
u
C6
76
10
uC
18
10
uC
19
100pC455
10
0p
C4
87
100pC489
10
0p
C4
57
10
00
p
C2
66
10
0p
C4
81
10
0p
C4
58
10
00
p
C2
59
10
0p
C4
59
10
0p
C4
80
10
0p
C4
85
10
0p
C4
84
10
0p
C4
83
10
0p
C4
05
10
0p
C4
86
10
0p
C4
82
10
0p
C4
47
10
0p
C4
88
(B)
9p
C2
04
10
00
p
C2
39
10
00
p
C2
34
1000pC218
10
00
p
C2
35
68pC233
1000pC225
10
00
p
C2
41
10
00
p
C2
20
22
pC
2
18pC422
15p
C423
0.1
u
C2
40
(G)39p
C320
27p
C308
10
00
pC
34
1
100p
C223
10
00
pC
65
18
p
C2
53
$C
21
7
$C
21
9
4p
C319
15p
C309
$C
22
9
$C
23
0
(B)3p
C317
(G)
18
p
C2
47
12pC312
1000p
C246
(B)4pC250
(B)9pC248
(G)
15
p
C2
49 (B
)8
pC2
51
470pC4
47
0p
C2
8
470pC6
10
00
p
C2
58
470pC14
470pC8
47
0p
C4
56
470pC5
470pC10
0.1
uC
43
8
0.1
uC
64
0.1
uC
45
1
0.1
u
C5
02
0.1
uC
43
7
0.1
uC
43
9
0.1
u
C428
0.1
uC
45
0
0.1
u
C6
2
0.1
uC
44
3
0.1
uC
44
0
0.1
u
C425
0.1u
C500
0.1
u
C4
34
0.1
u
C6
3
0.1
u
C426
0.1
u
C4
98
0.1
uC
43
5
0.1
u
C4
99
0.1u
C497
0.1
uC
44
4
0.1
u
C427
0.1
uC
44
1
0.1
uC
44
6
0.1
uC
42
10.1
uC
44
2
0.01uC449
0.0
1u
C4
07
$C
24
2
$C
20
1
(G)
15
pC
20
5
Q72SB1132(Q,R)
RR
1L
AM
4S
D1
TX-RX UNIT (XC1-178K-00 (NX-3220))
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA053<Rev.001>) 2-17
(D)270k
R30
(D)
180kR100
R7
6800p
C3
+
S
-
7.5V
CN9
+BCN3
1000p
C1
22p
C2
3.15A
LB73F0AW-002L1
FZA10BQ-3R15
F1
RR
1LA
M4S
D1
0
R31
NC
3
VIN
2
VS
S
4
VoU
T
1
BATT INT
XC
61C
C5602N
-GIC
1470p
C17
DAN222
D8
470p
C37 4
70k
R12
10k
R13
470k
R14
EM
D12
Q1
10k
R15
470k
R48
470k
R49
SSM6N15AFEM
Q3
100kR20
100kR21
SSM6N15AFEMQ2
470k
R16
470k
R17
100k
R18
100kR19
16V
16V
1
R52
16
15
14
13
LB73G0AM-004L3
10u
C18
10u
C19
38M
3300p
C20
PG
4
SW
33
SW
22
SW
11
PGND2PGND1
VoS
EN
PV
IN2
12
PV
IN1
11
AV
IN1
0S
S/T
R9
DEF 8
FSW 7
AGND 6
FB 5470p
C36
3.8V
L5
(D)
68kR23
(D)
18kR
22
0.1
u
C21
22u
C22
LB73G0AM-0042.2u
L4
TPS62140RGT
IC3
NC
NC
54
2
3 1
A
FEDCB
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720CQ-0313ACN1
470pC7
6800pC9
470pC4
470pC6
470pC14
470pC8
470pC5
470pC10
50A
ENC2
ENC1ENC3
ENC0RK74HB1J101JCP2
2.2k
R11
SB1CN4
$R
6
3.1V31BUBATT CHK
LB
73H
0A
V-0
02
L10
0.1
uC
38
CN
2CE
6
VS
S
5
NC
2
4
VoU
T
3
NC
1
2
VIN
1
XC
6209B
312D
-GIC
9
1k
R39
RB520SM-30D9
25
1uC
39
1.2V
12BU12BU
0.1
uC
40
CN5
VoU
T
3
VS
S
2
VIN
4
CE
1XC
6215B
122N
-GIC
10
0.1
u
C41
OSCGNDB
NC
U15W
F104F
6S
TH
401
-t
0.0
1u
C401
L7H-0076-00
22
R410
0
R402
LB73H0AV-002L401
0.0
1u
C403
100p
C402
10
R403
1k
R401
VCC 4
oUT 3GND2
VC1
19.2MHzX401
22
R404
0.01u
C404
33k
R406
15k
R405
TE
MP
FC
NT
680
R408
10
R407
Q4012SC4617/S/
0.01u
C406
(-86)4.7u
L402
5p
C408
$R
409
22
R414
22
R413
0
R412
100p
C405
0.0
1u
C407
1.8V
18M
VOL
6.3
10uC24
100k
R25
4.7
u
C23
VoUT3EN2
GND
4VIN1
LXDC2HN18F163IC4
1k
R24
LB73G0AM-004L6
3.2V
32M
0.4
7u
C26
0.4
7u
C25
LB73G0AM-004L7 0
.1u
C35
10k
R26 CE3 VSS 2
VIN4 VoUT 1
IC5
5.0V
50C
SBC
0.1
u
C27
CE
6
VS
S
5
NC
2
4
VoU
T
3
NC
1
2
VIN
1
XC6209B502D-GIC6
2.2
u
C29
470p
C28
SB2
SBC
BATT
/PSW
/BINT
470k
R29
470p
C30
(D)
470k
R66
(D)
470k
R65
270k
R27
220k
R28
VT6M1
Q4
SDET
VOL
1.2V
1/4
W
12M 100k
R36
100k
R37
VT
6M
1
Q5
100
R35
6.3
10uC32
GN
D_
3 9
GN
D_
2 8
EN7
VIN_26
VIN_15
GND_1
4
VoUT_2 3
VoUT_1 2
MoDE 1
LXDC2XQ12A-252IC2
100k
R33
10
u
C31
1k
R32
2.7
R38
47k
R34
1.8V
18BT
18BT
0.2
2u
*C15
0.2
2u
*C16
LB73H0AV-002*L9
1k
*R8 STBY3 GND 2
VIN4 VoUT 1
BU18TD2WNVX*IC8
3.2V
32BT
LB73G0AM-004*L8
1k
*R9 STBY3 GND 2
VIN4 VoUT 1
*IC7
0.2
2u
*C34
0.2
2u
*C33
3.2V
32A
1k
R40
0.4
7u
C430.1
u
C42 VoU
T3
GN
D
2
VIN
4
CoN
TR
oL
1
NJM2878F4-32IC11
LB73H0AV-002L11
1.8V
32A
Load Switch
18M SW
BT_CLK
CE
3 VSS 2
VIN
4 VoUT 1
XC8102AA07-GIC12
47k
R41
0.1uC44
CN
406
CN
409
CN
408
CN
405
CN
407
2.2
kR
425
22
R428
2.2
kR
421
1k
R426
2.2
kR
420
2.2
kR
424
2.2
kR
427
2.2
kR
423
2.2
kR
422
BO
OT
[3]
BO
OT
[7]
BO
OT
[0]
BO
OT
[2]
BO
OT
[6]
BO
OT
[4]
BO
OT
[5]
BO
OT
[1]
LE
D_
G
LE
D_
R
LE
D_
B
/TX
D1
_JK
_E
N
PL
D
/IN
T_
PT
T
LC
D_
BL
C
SB
C
DD
R_
RA
S
DD
R_
A[1
]
DD
R_
D[3
]
DD
R_
D[1
1]
DD
R_
A[5
]
DD
R_
DQ
S[0
]
DD
R_
A[4
]
DD
R_
D[1
5]
DD
R_
D[2
]
DD
R_
CA
S
DD
R_
D[9
]
DD
R_
A[0
]
DD
R_
A[8
]
DD
R_
CS
DD
R_
D[1
3]
DD
R_
D[6
]
DD
R_
D[1
4]
DD
R_
A[3
]
DD
R_
WE
DD
R_
A[1
1]
DD
R_
D[5
]
DD
R_
DQ
S[1
]
DD
R_
A[2
]
DD
R_
D[1
0]
DD
R_
A[7
]
DD
R_
D[8
]
DD
R_
A[9
]
DD
R_
CL
KP
DD
R_
DQ
M[0
]
DD
R_
A[6
]
DD
R_
BA
[0]
DD
R_
DQ
M[1
]
DD
R_
D[1
]
DD
R_
D[0
]
DD
R_
CL
KN
DD
R_
A[1
2]
DD
R_
D[7
]
DD
R_
BA
[1]
DD
R_
A[1
3]
DD
R_
D[1
2]
DD
R_
CK
E
DD
R_
A[1
0]
DD
R_
D[4
]
CN
41
9
CN
41
8
CN
41
5
CN
41
3
CN
41
6
CN
41
7
CN
41
4
W1 W2 W3 V1 V2 V3 U1 U2 U3 T1 T2 T3 R1 R2 R3 P4 R12 R11 V8 T9 U8 V11 T14 R10W13 V9 U9 W9 T8 V7 W7 W8 U7 T7 W6 V6 U5 V5 W5 U6 U4 T6 W4 T4 V4 T5 U15 U14 V14 U13 V13 V12W12W11 T13 T11 T10 T12 U10 V10 U11W10
LC
D_
D<
0>
LC
D_
D<
1>
LC
D_
D<
2>
LC
D_
D<
3>
LC
D_
D<
4>
LC
D_
D<
5>
LC
D_
D<
6>
LC
D_
D<
7>
LC
D_
D<
8>
/Bo
oT
<0
>
LC
D_
D<
9>
/Bo
oT
<1
>
LC
D_
D<
10
>/B
oo
T<
2>
LC
D_
D<
11
>/B
oo
T<
3>
LC
D_
D<
12
>/B
oo
T<
4>
LC
D_
D<
13
>/B
oo
T<
5>
LC
D_
D<
14
>/B
oo
T<
6>
LC
D_
D<
15
>/B
oo
T<
7>
DD
R_
DQ
GA
TE
1
DD
R_
DQ
GA
TE
0
DD
R_
BA
<0
>
DD
R_
BA
<1
>
DD
R_
BA
<2
>
DD
R_
DQ
S<
1>
DD
R_
DQ
S<
0>
DD
R_
DQ
M<
1>
DD
R_
DQ
M<
0>
DD
R_
CS
DD
R_
CA
S
DD
R_
RA
S
DD
R_
WE
DD
R_
CK
E
DD
R_
CL
KN
DD
R_
CL
KP
DD
R_
A<
0>
DD
R_
A<
1>
DD
R_
A<
2>
DD
R_
A<
3>
DD
R_
A<
4>
DD
R_
A<
5>
DD
R_
A<
6>
DD
R_
A<
7>
DD
R_
A<
8>
DD
R_
A<
9>
DD
R_
A<
10
>
DD
R_
A<
11
>
DD
R_
A<
12
>
DD
R_
A<
13
>
DD
R_
D<
0>
DD
R_
D<
1>
DD
R_
D<
2>
DD
R_
D<
3>
DD
R_
D<
4>
DD
R_
D<
5>
DD
R_
D<
6>
DD
R_
D<
7>
DD
R_
D<
8>
DD
R_
D<
9>
DD
R_
D<
10
>
DD
R_
D<
11
>
DD
R_
D<
12
>
DD
R_
D<
13
>
DD
R_
D<
14
>
DD
R_
D<
15
>
OMAP
K4
J3
K3
H3
W19
W18
W17
V17
W16
R14
V16
U18
P17
R15
R19
R18
T16
U19
V19
V18
V15
W14
N3
N1
N2
J2
J1
L2
L1
R5
G4
H4
F2
F1
E9
P19
P18
N17
K18
N19
P16
M19
M18
F4
H19
J19
K19
L19
T18
K17
K16
J16
L17
J15
J18
M16
L16
T17
J17
K14
32M_1_1
USB0_DP
USB0_DM
RTC_ALARM/DEEPSLEEP
RTC_Xo
RTC_XI
oSCoUT
oSCIN
CLKoUT
RTCK/GP8<0>
EMU1
EMU0
TRST
TCK
TDo
TDI
TMS
RESEToUT
NMI
RESET
GP6<6>
GP6<7>
SATA_REG
SATA_REFCLKN
SATA_REFCLKP
SATA_TXN
SATA_TXP
SATA_RXN
SATA_RXP
LCD_AC_ENB_CS
MMCSD1_DAT<4>/LCD_VSYNC
MMCSD1_DAT<5>/LCD_HSYNC
MMCSD1_DAT<6>/LCD_MCLK
MMCSD1_DAT<7>/LCD_PCLK
MMCSD0_CLK
USB1_DP
USB1_DM
USB0_VDDA12
USB0_DRVVBUS
USB0_VBUS
USB0_ID
RMII_RXER/PRU0_R31<24>
RMII_RXD<0>/PRU0_R31<25>
RMII_RXD<1>/PRU0_R31<26>
RMII_TXEN/PRU0_R31<27>
RMII_TXD<0>/PRU0_R31<28>
RMII_TXD<1>/PRU0_R31<29>
GP6<5>
PRU0_R30<9>/PRU0_R31<9>
PRU0_R30<10>/PRU0_R31<10>
PRU0_R30<11>/PRU0_R31<11>
PRU0_R30<12>/PRU0_R31<12>
PRU0_R30<13>/PRU0_R31<13>
PRU0_R30<14>/PRU0_R31<14>
PRU0_R30<15>/PRU0_R31<15>
B19B18B15C8A5B9D10B16F9A17B17A18A9A16D8B7A15C15C14D15B14D14A14C13E13B13A13D12C12B12D13D11A12C11E12B11E11C10A11B10A10C9A8B8E8B5E7C6D7E10D9A7D6A6B6C7E6
PRU1_R30<0>/PRU1_R31<1>MMCSD1_DAT<1>/PRU1_R30<1>/PRU1_R31<2>MMCSD1_DAT<2>/PRU1_R30<2>/PRU1_R31<3>MMCSD1_DAT<3>/PRU1_R30<3>/PRU1_R31<4>RMII_CRS_DV/PRU1_R31<29>RMII_MHZ_50_CLK/PRU0_R31<23>
Bypass capacitors for OMAP
EM
A_
WA
IT<
1>
EM
A_
WA
IT<
0>
EM
A_
oE
EM
A_
WE
N_
DQ
M<
0>
EM
A_
WE
N_
DQ
M<
1>
EM
A_
WE
EM
A_
A_
RW
EM
A_
CS
<5
>
EM
A_
CS
<4
>
EM
A_
CS
<3
>
EM
A_
CS
<2
>
EM
A_
CS
<0
>
EM
A_
CA
S
EM
A_
RA
S
EM
A_
SD
CK
E
EM
A_
CL
K
EM
A_
BA
<1
>
EM
A_
BA
<0
>
EM
A_
A<
0>
EM
A_
A<
1>
EM
A_
A<
2>
EM
A_
A<
3>
EM
A_
A<
4>
EM
A_
A<
5>
EM
A_
A<
6>
EM
A_
A<
7>
EM
A_
A<
8>
EM
A_
A<
9>
EM
A_
A<
10
>
EM
A_
A<
11
>
EM
A_
A<
12
>
EM
A_
A<
13
>
EM
A_
A<
14
>/M
MC
SD
0_
DA
T<
7>
EM
A_
A<
15
>/M
MC
SD
0_
DA
T<
6>
EM
A_
A<
16
>/M
MC
SD
0_
DA
T<
5>
EM
A_
A<
17
>/M
MC
SD
0_
DA
T<
4>
EM
A_
A<
18
>/M
MC
SD
0_
DA
T<
3>
EM
A_
A<
19
>/M
MC
SD
0_
DA
T<
2>
EM
A_
A<
20
>/M
MC
SD
0_
DA
T<
1>
EM
A_
A<
21
>/M
MC
SD
0_
DA
T<
0>
EM
A_
A<
22
>/M
MC
SD
0_
CM
D
EM
A_
D<
0>
EM
A_
D<
1>
EM
A_
D<
2>
EM
A_
D<
3>
EM
A_
D<
4>
EM
A_
D<
5>
EM
A_
D<
6>
EM
A_
D<
7>
EM
A_
D<
8>
EM
A_
D<
9>
EM
A_
D<
10
>
EM
A_
D<
11
>
EM
A_
D<
12
>
EM
A_
D<
13
>
EM
A_
D<
14
>
EM
A_
D<
15
>
D5
C2
A1
A2
B2
B1
A3
F3
E1
E2
E3
D1
D3
C1
D2
E4
C3
D4
C5
C4
B3
B4
A4
G3
J4
G2
G1
T15
U16
W15
U17
R16
R17
H17
G17
G16
G18
F17
F16
E18
F19
F18
E19
H16
G19
C16
C18
C19
D18
E17
D16
E16
D17
C17
D19
SPI1_SCS<7>/I2C0_SCLSPI1_SCS<6>/I2C0_SDA
SPI1_SCS<5>/UART2_RXDSPI1_SCS<4>/UART2_TXDSPI1_SCS<3>/UART1_RXDSPI1_SCS<2>/UART1_TXD
SPI1_SCS<1>
SPI1_SCS<0>
SPI1_ENA
SPI1_CLK
SPI0_SoMI/MII_RXER
SPI0_SIMo/MII_CRS
SPI0_SCS<5>/UART0_RXD/MII_RXD<3>
SPI0_SCS<4>/UART0_TXD/MII_RXD<2>
SPI0_SCS<3>/UART0_CTS/MII_RXD<1>
SPI0_SCS<2>/UART0_RTS/MII_RXD<0>
SPI0_SCS<1>/MDIo_CLK
SPI0_SCS<0>/MDIo_D
SPI0_ENA/MII_RXDV
SPI0_CLK/MII_RXCLK
AXR13/CLKX1
AXR14/CLKR1
AXR15/ECAP2_APWM2
GP8<12>
MMCSD1_CMD
MMCSD1_CLK
MMCSD1_DAT<0>
GP6<8>
GP6<9>
GP6<10>
GP6<11>
GP6<12>
GP6<13>
SPI1_SoMI
SPI1_SIMo
ACLKX
AHCLKX/USB_REFCLKIN/UART1_CTS
AXR0/ECAP0_APWM0/MII_TXD<0>/CLKS0
AXR1/DX0/MII_TXD<1>
AXR2/DR0/MII_TXD<2>
AXR3/FSX0/MII_TXD<3>
AXR4/FSR0/MII_CoL
AXR5/CLKX0/MII_TXCLK
AXR6/CLKR0/MII_TXEN
AXR7
AXR8/CLKS1/ECAP1_APWM1
AXR9/DX1
AXR10/DR1
AXR11/FSX1
AXR12/FSR1
AMUTE/UART2_RTS
AFSR
ACLKR
AHCLKR/UART1_RTS
AFSX
12
M_
1_
2
12
M_
1_
1
18
M_
1_
1
R13 P13 L6 K5 J13 G12 G11 G10 G6 F14 N7 H14 E5 N8 M9 M8 L12 K12 K6 J12 J6 H13 H12 H11 H10 H7 H6 G13 G8 G7 E15
DV
DD
18
_1
0
DV
DD
18
_9
DV
DD
18
_8
DV
DD
18
_7
DV
DD
18
_6
DV
DD
18
_5
DV
DD
18
_4
DV
DD
18
_3
DV
DD
18
_2
DV
DD
18
_1
RV
DD
3
RV
DD
2
RV
DD
1
CV
DD
18
CV
DD
17
CV
DD
16
CV
DD
15
CV
DD
14
CV
DD
13
CV
DD
12
CV
DD
11
CV
DD
10
CV
DD
9
CV
DD
8
CV
DD
7
CV
DD
6
CV
DD
5
CV
DD
4
CV
DD
3
CV
DD
2
CV
DD
1
M3
T19
N4
P2
P1
M2
P3
M12
P14
P15
N14
N18
R9
R8
R7
P10
P9
P8
P7
N10
N9
N6
R6
U12
L14
N15
L15
NC3
RSV2
SATA_VDD4
SATA_VDD3
SATA_VDD2
SATA_VDD1
SATA_VDDR
USB_CVDD
USB1_VDDA18
USB1_VDDA33
USB0_VDDA18
USB0_VDDA33
DDR_DVDD18_10
DDR_DVDD18_9
DDR_DVDD18_8
DDR_DVDD18_7
DDR_DVDD18_6
DDR_DVDD18_5
DDR_DVDD18_4
DDR_DVDD18_3
DDR_DVDD18_2
DDR_DVDD18_1
DDR_VREF
DDR_ZP
RTC_CVDD
PLL1_VDDA
PLL0_VDDA
P11N12N11N5M11M10M7M6M5M4L11L10L9L8L7L5K11K10K9K8K7J11J10J9J8J7H15H9H8A19N16M14M1L3K2K1H2H1H18M15M17L18
VS
S3
0
VS
S2
9
VS
S2
8
VS
S2
7
VS
S2
6
VS
S2
5
VS
S2
4
VS
S2
3
VS
S2
2
VS
S2
1
VS
S2
0
VS
S1
9
VS
S1
8
VS
S1
7
VS
S1
6
VS
S1
5
VS
S1
4
VS
S1
3
VS
S1
2
VS
S1
1
VS
S1
0
VS
S9
VS
S8
VS
S7
VS
S6
VS
S5
VS
S4
VS
S3
VS
S2
VS
S1
NC
2
NC
1
SA
TA
_V
SS
6
SA
TA
_V
SS
5
SA
TA
_V
SS
4
SA
TA
_V
SS
3
SA
TA
_V
SS
2
SA
TA
_V
SS
1
RT
C_
VS
S
PL
L1
_V
SS
A
PL
L0
_V
SS
A
oS
CV
SS
IC401
R4
P12
P6
P5
N13
M13
L13
L4
K13
J5
K15
J14
G9
F13
F12
F11
F10
F8
F7
F6
E14
H5
G15
G14
G5
F15
F5
DVDD3318_C10DVDD3318_C9DVDD3318_C8DVDD3318_C7
DVDD3318_C6
DVDD3318_C5
DVDD3318_C4
DVDD3318_C3
DVDD3318_C2
DVDD3318_C1
DVDD3318_B11
DVDD3318_B10
DVDD3318_B9
DVDD3318_B8
DVDD3318_B7
DVDD3318_B6
DVDD3318_B5
DVDD3318_B4
DVDD3318_B3
DVDD3318_B2
DVDD3318_B1
DVDD3318_A6
DVDD3318_A5
DVDD3318_A4
DVDD3318_A3
DVDD3318_A2
DVDD3318_A1
32M_1_1
18M_1_1
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
32
M_
1_
1
32
M_
1
18
M_
2_
2
18
M_
2_
1
12
M_
1_
11
2M
_1
_2
18
M_
2
18
M_
1_
1
18
M_
1
12
M_
1
RTCGNDG
OSCGNDB
$C
41
5
$C
41
3
L79-1946-05L416
10
u
C4
30
$C
41
9
$C
41
8
L79-1946-05
L415
L79-1946-05L414
$C
42
0
L79-1946-05L413
$C
41
4
$C
41
2
$C
41
1
$C
41
0
L79-1946-05L412
L79-1946-05L411
4.7
uC
43
1
10
u
C4
29
$C
41
6
4.7
uC
43
3
10
uC
43
2 $C
41
7
12BU
PLL0_VDDA
PLL1_VDDA
1k
R4
39
1k
R4
40
49.9
R438
10
0p
C4
87
100pC489
10
0p
C4
88
0.1
u
C4
34
0.1
uC
43
5
32M_1_1
18M_2_2
18M_2_1
18M_1_1
12M_1_2
$CN401
10
9
8
7
6
5
4
3
2
1
/RST
19
.2M
/FRST
10kR433
CTS2
USB_DET
USB0_DM
/WP
VBUS
USB0_DP
MCLK
RTCGNDG
CN450
CN412
1M
R435
0
R430
0
R437
L77-1802-05X402
0.22u
C424
100pC455
18pC422
15p
C423
0.1
uC
421
10kR434
10kR432
/EMG
/SIDE1
KEYO0
/KEYI0
KEYO3
KEYO2
/KEYI2
AGCKEEP
LBC_B
LBC_R
KEYO1
22k
R431
0
R436
/DCR_RST
SYMTIM_IN
FL
DM
DA
TA
[6]
AD
D[1
6]
AD
D[0
]
AD
D[1
0]
AD
D[1
]
DA
TA
[3]
DA
TA
[7]
AD
D[1
8]
DA
TA
[10
]
AD
D[1
4]
DA
TA
[14
]
DA
TA
[0]
AD
D[1
1]
AD
D[2
]
DA
TA
[1]
DA
TA
[11
]
AD
D[1
5]
AD
D[1
9]
AD
D[4
]
DA
TA
[2]
DA
TA
[12
]
AD
D[7
]
DA
TA
[8]
AD
D[8
]
AD
D[2
1]
AD
D[9
]
DA
TA
[5]
DA
TA
[4]
DA
TA
[13
]
AD
D[1
2]
AD
D[2
3]
AD
D[6
]
AD
D[2
2]
AD
D[1
7]
AD
D[3
]
DA
TA
[15
]
AD
D[2
0]
DA
TA
[9]
AD
D[1
3]
AD
D[5
]
ENC2
ENC1
/CINT
/PSW
/SIDE2
/KEYI1
/KEYI3
/KEYI4
USB_VBUS_0RB521CM-30
D401
470p
C456
1.8V
1.8V DDR
LB
73G
0A
M-0
04
L409
10u
C436
100p
C457
100p
C481
100p
C458
100p
C459
100p
C480
100p
C482
0.1
uC
438
0.1
uC
437
0.1
uC
439
0.1
uC
443
0.1
uC
440
0.1
uC
444
0.1
uC
441
0.1
uC
442
DD
R_D
[7]
DD
R_D
[12]
DD
R_D
[5]
DD
R_D
QS
[1]
DD
R_D
[9]
DD
R_D
[6]
DD
R_D
[0]
DD
R_D
[15]
DD
R_D
[4]
DD
R_D
[10]
DD
R_D
[3]
DD
R_D
[14]
DD
R_A
[13]
DD
R_D
[8]
DD
R_D
[1]
DD
R_D
[2]
DD
R_D
[11]
DD
R_D
QS
[0]
DD
R_A
[12]
DD
R_D
[13]
DD
R_C
KE
DD
R_A
[8]
DD
R_A
[3]
DD
R_A
[7]
DD
R_C
S
DD
R_A
[4]
DD
R_A
[2]
DD
R_C
AS
DD
R_A
[1]
DD
R_D
QM
[0]
DD
R_B
A[1
]
DD
R_A
[0]
DD
R_B
A[0
]
DD
R_A
[5]
DD
R_A
[6]
DD
R_D
QM
[1]
DD
R_C
LK
N
DD
R_A
[9]
DD
R_C
LK
P
DD
R_A
[10]
DD
R_A
[11]
DD
R_W
E
DD
R_R
AS
VSSQ5 E1
VSSQ1 D9
VSSQ4 C1
VSSQ3 B9
VSSQ2 A3
VSS3 K1
VSS2 F1
VSS1 A1
VDDQ5E9
VDDQ4D1
VDDQ3C9
VDDQ2B1
VDDQ1A7
VDD3K9
VDD2F9
VDD1A9
A12
H3
NC
1
F7
NC
2
F3
UD
QS
E2
LD
QS
E8
DQ
15
A2
DQ
14
B3
DQ
13
B2
DQ
12
C3
DQ
11
C2
DQ
10
D3
DQ
9
D2
DQ
8
E3
DQ
7
E7
DQ
6
D8
DQ
5
D7
DQ
4
C8
DQ
3
C7
DQ
2
B8
DQ
1
B7
DQ
0
A8
UD
M
F2
LD
M
F8
WE
G7
CA
S
G8
RA
S
G9
BA
1
H9
BA
0
H8
CS
H7
CK
E
G1
CK
G2
CK
G3
A11
H2
A10/A
P
J7
A9
H1
A8
J3
A7
J2
A6
J1
A5
K3
A4
K2
A3
K8
A2
K7
A1
J9
A0
J8
IC402
38M
18M
Flash
32M
/RS
T
VD
D
3
DS
2
oU
T
4
VS
S
1
S-80135ANPF-GIC403
4.7
kR
442
0.0
1u
C448
LOW = UART OR USB LOADER
FLDM
CN423
CN424
1k
R429
0
R451
$L403
18M_3
VCC
5
oUTY
4GND3
INA2
INB1
TC7SZ08FE
IC405
LB73G0AM-004
L410
0.01uC449
FOr BYTE PORT
/WP internal Pull-Up
/WR
/OE
/FR
ST
AD
D[2
0]
/CS
_F
AD
D[1
9]
AD
D[2
2]
/WP
AD
D[2
1]
AD
D[2
3]
CN
437
CN
436
CN
422
VSS1E8VSS2
H2VSS3
H7
NC
1
A1
NC
2
A8
RF
U1
B1
RF
U2
C1
RF
U3
D1
NC
3
H1
NC
4
H8
RY
/BY
A4
VIo
2
D8
VIo
1
F1
WP
/AC
C
B4
RE
SE
T
B5
WE
A5
oE
G2
CE
F2
A2
5
G8
A2
4
F8
A2
3
C8
A2
2
B8
A2
1
C5
A2
0
D4
A1
9
D5
IC404
4.7k
R445
100kR444
100k
R443
RB521CM-30D402
1u
C452
0.1
uC
451
0.1
uC
450
AD
D[5
]
AD
D[1
3]
AD
D[7
]
DA
TA
[12]
DA
TA
[9]
DA
TA
[11]
AD
D[3
]
AD
D[6
]
AD
D[8
]D
AT
A[8
]
AD
D[1
4]
AD
D[9
]
DA
TA
[13]
AD
D[4
]
DA
TA
[14]
DA
TA
[15]
AD
D[1
8]
DA
TA
[3]
AD
D[1
6]
DA
TA
[0]
DA
TA
[6]
AD
D[1
2]
DA
TA
[10]
AD
D[2
]
AD
D[1
0]
DA
TA
[1]
AD
D[1
7]
DA
TA
[2]
DA
TA
[4]
AD
D[1
]
DA
TA
[5]
DA
TA
[7]
AD
D[1
5]
AD
D[0
]
AD
D[1
1]
VCCG5
BY
TE
F7
RF
U5
G1
DQ
15
/A-1
G7
DQ
14
F6
DQ
13
G6
DQ
12
F5
DQ
11
G4
DQ
10
F4
DQ
9
G3
DQ
8
F3
DQ
7
E6
DQ
6
H6
DQ
5
E5
DQ
4
H5
DQ
3
H4
DQ
2
E4
DQ
1
H3
DQ
0
E3
A1
7
B3
A1
6
E7
A1
5
D7
A1
4
C7
A1
3
A7
A1
2
B7
A1
1
D6
A1
0
C6
A9
A6
A8
B6
A7
A3
A6
C3
A5
D3
A4
B2
A3
A2
A2
C2
A1
D2
A0
E2100p
C447
RF
U4
E1
A1
8
C4
CN
421
1u
C445
0.1
uC
446
BLS
F1B-0087-00E401
VC
O_
H_
/L
EX
TS
PD
ET
GP
S_
PA
_E
N
VE
R2
GP
SB
T_
DE
T
VE
R1
OP
CN
_T
YP
/BT
_S
HU
TD
OW
N
MO
DE
L
/CS
3
/OE
/SA
VE
/WR
/CS
4
AS
TS
W
$R
41
82.2
k*R
41
9
$R
41
7
$R
41
6
2.2
k
R4
41
/CS
_F
LBC_G
5VC
/ADC
RX
ANTSWUSB_VBUS
/APCSWAPCSW2
SCK0
TX
100*4
CP401
CN447
CN445
10
0p
C4
85
10
0p
C4
84
10
0p
C4
83
10
0p
C4
86
ENC3
/ADC_INT
TXD2
RXD2
/DACCS
/APCSW_0
SCK1
TXD1
/EXT_PTT
SDO1
I2CDT
I2CCK
RXD1
SDO0
SDI0
ENC0
APCSW2_0
/DSW
TXC
ANTSW_0
CN443
(OUT)
KEY_INT
BT_AUD_DO
BT_AUD_DI
DCR_DI
DCR_DDO
CODEC_DO
DCR_DO
/DCR_CS
DCR_ADI
/DCR_DCS
DCR_ACLK
CODEC_DI
/DCR_ACS
LCD_RST
/BINT
SYMTIM_IN
EXTMIC_SW
RTS2
USB_SW
RTS1
BCLK
/OPTDETLB73H0AV-002
L417
CN455
CN439
330R450 WCLK
3.2V
1.8V
1.8V
1.2V
1.2V
1.2V
32M
18M
12M
32M_1
18M_2
18M_1
PLL1_VDDA
PLL0_VDDA
12M_1
0
R452
L404
L407
L408
L406
L405
0.1
u
C4
28
0.1
u
C4
25
0.1
u
C4
26
0.1
u
C4
27
50A
12BU12M
32A
18M_3
18M
38M
32M
OMAP 1.8V_block:white
OMAP 3.2V_block:blue
32B
T
SBC
38M
3.3
uC
46
3.3
uC
47
CK
73F
XR
1E
475K
4.7
uC
48
R92-3774-0527
R43R92-3774-05
27
R42
20V DC/DCL41-1502-70
15uL12
$C
45
SW
6
NC
5
FB
4EN3
VIN2
GND1
TPS61041DRVRIC13
470k
R44
CK
730JM
1H
684K
0.6
8u
C50
RB561VM-40D10
680p
C52
680p
C49
33k
R45
22
R46
3.2V
32C
LB73H0AV-002L13
0.2
2u
C51
0.2
2u
C53
STBYGND 2
VINVoUT 1
IC14
34
18
BT
_A
FS
YN
C
18
BT
_R
X
18
BT
_T
X
18
BT
_A
IN
18
BT
_A
CL
K
18
BT
_A
OU
T
18
BT
_R
TS
18
BT
_C
TS
/BT
_S
HU
TD
OW
N
100
*R353
1u
*C365
1u
*C364
18p
*C363
BT_TX_DBGXCN352
0.1
u*C
368
0.1
u*C
367
3.2V
1.8V
L92-0487-05*L352
0.1u
*C361
0.1u*C360
L92-0487-05
*L351
BT_CLK
0.01uC356
47k
*R361
GPS_PPS_OUTCN351
BT_CLK_REQ
CN355100*R351
0.1u*C386
1u*C388
$C362
10k
R360
0.1u*C358
0.1u*C387
0.1u*C359
1u*C357
GP
SA
NT
L1
J2
J1
J3
H3
H2
F5
E3
F4
E4
D5
C6
C4
H1
F3
F2
G1
G2
F1
E1
E2
D4
C2
C1
B2
B1
A1
GPS&BLUETOOTH
VSS_LNA_GPS1
VDD_PLL_GPS
VSS_PLL_GPS
VDD1P8_GPS
GPS_TP
GPS_TM
GPS_UART_TX
GPS_UART_RX
GPS_SENS_I2C_SCL
GPS_SENS_I2C_SDA
GPS_nSHUTDoWN
GPS_TIMESTAMP
GPS_PPS_oUT
TCXo_LDo_IN
VSS_DIG2
VDD_DIG2
VDD_TCXo
VSS_TCXo_CLK
TCXo_CLK_LV
TCXo_LDo_VPRoG
VDDS4
TCXo_CLK_REQ
VSS_DIG5
VDD_SRAM_LDo
VDD_DIG_LDo
VDD1P8V_1
PMTEST_1P8V
*IC351
A2
A3
B3
D1
D2
D3
C3
A4
B5
B4
B7
A5
A6
E5
B6
H5
D7
C5
D6
C7
B8
A7
A8
A9
B9
A1
0
VB
AT
1
VD
D1
P8
V_
2
VD
DS
1
BT
_A
UD
_C
LK
BT
_A
UD
_F
SY
NC
BT
_A
UD
_IN
BT
_A
UD
_o
UT
BT
_H
CI_
UA
RT
_T
X
BT
_H
CI_
UA
RT
_R
X
BT
_H
CI_
UA
RT
_C
TS
BT
_H
CI_
UA
RT
_R
TS
BT
_H
oS
T_
WA
KE
UP
BT
FM
_n
SH
UT
Do
WN
VD
D_
DIG
1
VS
S_
DIG
6
BT
_G
PIo
<6
>
BT
_G
PIo
<5
>
BT
_G
PIo
<4
>
BT
_G
PIo
<3
>
BT
_G
PIo
<2
>
BT
_T
ES
TT
P
VS
S_
DP
LL
_B
T
VD
D_
DC
o_
BT
VS
S_
DC
o_
BT
VD
D_
RF
_B
TB
T_
TE
ST
TM
L1
0
J9
K9
L9
K8
L8
J7
K7
L7
J6
K6
L6
J5
K5
L5
G4
J4
L4
H4
G3
H6
G5
K3
K4
L3
L2
K2
TE
ST
_E
N
VS
S_
PA
_F
M
FM
_R
FP
_o
UT
FM
_R
FP
_IN
VS
S_
RF
_F
M
FM
_A
BG
AP
_C
AP
VS
S_
AD
CP
LL
_F
M
FM
_A
UD
_o
UT
_R
FM
_A
UD
_o
UT
_L
RE
F_
CL
K_
RE
Q
VD
D_
DIG
3
VP
P
VS
S_
DIG
4
VD
DS
3
VD
D_
SR
AM
2
CL
K_
RE
QP
oL
VS
EN
SE
IFo
RC
E
GP
S_
I2C
_U
AR
T_
SE
L
GP
S_
PA
_E
N
GP
S_
EX
T_
LN
A_
EN
GP
S_
IRQ
VS
S_
MIX
_G
PS
VD
D_
IF_
GP
S
VS
S_
LN
A_
GP
S2
GP
S_
LN
A_
IN
VS
S_
LN
A_
GP
S3
B1
0C
10
C8
D8
D9
D1
0E
7E
8H
10
E9
E1
0F
9F
10
G9
G1
0E
6F
6G
6F
8F
7G
7G
8H
7H
8H
9J8
J1
0
VSS_RF_BT
BT_RF
VDD1P8V_BT
VDD_LDoIN_CLASS1P5_BT
VDD_CLASS1P5_BT
VDD_PPAIF_BT
REF_CLK_LV
REF_CLK_HV
BT_WAKEUP
VSS_REF_CLK
VSS_DIG3
VDD_SRAM1
VDD_DIG4
VSS_DIG1
VDDS2
FM_I2C_SDA
FM_I2C_SCL
FM_IRQ
FM_I2S_CLK
FM_I2S_FSYNC
FM_I2S_oUT
FM_I2S_IN
FM_AUD_IN_L
FM_AUD_IN_R
RTC_CLK
VDD1P8_FM
VSS_PASYNTH_FM
1u*C370
0.1u*C3710.1u*C372
$C
390
L79-1987-05*L361
10p*C389
0.1u*C3730.1u*C374
CT
S2
RT
S2
TX
D2
RX
D2
18
BT
_T
X
18
BT
_R
X
18
BT
_C
TS
18
BT
_R
TS
B1
16
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1
VCC(A)
VCC(B)
DIR2
74AVC4TD245GU*IC352
10k
*R357
RK
74H
B1J100J
*CP
352
L92-0487-05*L366
L92-0487-05
*L365
0.1u*C384
0.1u*C381
BC
LK
WC
LK
BT
_A
UD
_D
OB
T_
AU
D_
DI
18
BT
_A
OU
T
18
BT
_A
FS
YN
C
18
BT
_A
CL
KB
116
B2
15
B3
14
B4
13
DIR312
OE11
GND10
DIR49
A4
8
A3
7
A2
6
A1
5
DIR1
4
VCC(A) 3
VCC(B) 2
DIR2 1
74AVC4TD245GU*IC353
43
21
47p
*C382
RK
74H
B1J100J
*CP
351
10k
*R358
0.1u
*C383
0.1u
*C380
*Q351SSM3K15AMFV
LEVEL CONVERTOR
/BT
_S
HU
TD
OW
N
18
BT
_A
IN
BLS
F10-3228-15*E351
GP
S_
PA
_E
N
100
*R352
0.1
u
*C366
-32.768000k-NSA3534ANDK NZ2520BL77-3121-05*X351
(-71)10n
*L353
L92-0487-05
*L358
0.1
u*C
375
22p
*C369
120p
*C391
2.5
p*C
395
L7K-0059-00*L359
$R
370
$R
368
0*R369
150
*R356
150
*R354
39*R355
2.7V
GPS RF
FE
M_P
WR
FE
M_A
LM
G0B-0005-00*CN354
1000p
*C378
1000p
*C377
1000p
*C376
1000p
*C392
*CN356
27n
*L354
1k
*R364
1k
*R365
220
*R363220
*R362
32BT
BT RF
AN
TC
HK
*CN353
$L355
0*R359
47k
*R367
1k
*R366
1000p
*C3851
000p
*C379
4p*C354
G0B-0005-00*CN357
$C
353
$C
352
ASSIST
120kR105 10M
R108
100k
R107
100k
501uC105
1k
R104
10
R106
EM6M2Q102
V+
5
oUT
4IN-3
V-2
IN+1
OPA170AIDRLRIC101
ED
ZV
8.2
BD
102
4.7
k
R111
47
R109
100pC104
22k
R103
0.0
1u
C102
33pC103
$C
101
18.9V
0
R102
$R
101
$Q101
$D
101
CP
CV amp
AS
TS
W
CVAS
SIS
T
CN101
1kR112
0.1u
C106 100p
C107
VDD
5
oUT
4IN-3
VSS2
IN+1
BU7295HFVIC102
50C
50C
CP
Z
0
R137
4.3V
VC
O_M
OD
/SA
VE
47p
C111
10
4.7
u
C112
1S
S400S
MD
111
LB73H0AY-004L112
Q1132SD2654/W/
$Q115
VT6M1Q114
470k
R120
5.6
k
R122
10k
R121
22k
R124
0
R125 4
70k
R123
$R
113
22k
R142
3.9V
4.1V
VC
O_H
_/L
0.7
5p
C117
3p
C116
10
1uC113
LB73H0AY-004L111
SSM3K15AMFVQ116
Q111RE1E002SPVT6M1
Q112
0
R115
22
R116
47k
R114
22
R117
470k
R119
470k
R118
27k
R143
$R
144
3.2V
/SA
VE
VT6M1
Q103
470k
R141
470k
R140
0
R139
BLS
F1B-0095-00E101
L3C
-0002-0
0
L134
$C114
(B)
1p
C131
C138
(B)3pC136
(G)13p
C133
CK
73F
BB
1H
154K
0.1
5u
C121
CK
73F
B1H
473K
0.0
47u
C123
$C
137
(B)2pC134
47p
C135
47p
C132
10u
C122
D135
BB
Y58-0
2V
D131
BB
555-0
2V
H
D133
BB555-02VHD134
BB
555-0
2V
HD
132
(H0A
M)
100nL
135
(H0A
M)
100n
L132
(H0AM)100n
L131
LR
79Z
0G
J4N
7G
4.7
nL133
LB73H0AY-004L121
(D)390
R128
100k
R131
10k
R129
0
R127
150
R1300
R126
Overlap(G
)13pC
109
0.5
p
47p
C144
0.3
3u
C14047p
C139
47p
C150
(B)4pC142
(B)
4p
C143
(B)
2.5
pC
141
(B)1p
C145
0.1
u
C148
$C147
$C
149
$C
146
$C180
BB
555-0
2V
H
(-53)
100n
L137
(-53)
100n
L138
(-53)
100n
L136
Q131BFU660F
(D)
10k
R132
(D)
5.6
kR
133
8.2
R135
(D)
120
R134
0
R136
(B)
5pC
110
0.5
p
C158
47p
C159
(B)9pC161
BB
664-0
2V
D155
(-53)
150n
L156
100k
R151
(D)
10k
R153
VCOL
VCOH
L3C
-0001-0
0L155
(B)0.5pC115 (B)4pC156
47p
C154
47p
C152
(B)
4p
C151
(B)3pC157
0.1
u
C108
(G)13p
C153
$C
155
SM
V1130-0
79LF
D152
SM
V1130-0
79LF
D153
BB
Y58-0
2V
D151
BB555-02VHD154
LR
79Z
0G
J5N
1G
5.1
nL154
(H0A
M)
100n
L153
(H0A
M)
100n
L152
(H0AM)100n
L151
$L159
R110
(-53)
150n
L158
(D)
5.6
k
R152
47p
C164
0.3
3u
C160
(B)
7pC162
(B)
3.5
pC
163
$C179
$C
168
(-53)
150n
L157
Q151BFU660F
(D)
150
R154
4.7
R155
Overlap
47p
C167
$C
171
(B)2.5p
C166
0.1
u
C165
$C
170
$C
169
0
R156
(B)3pC183
47p
C182
47p
C181
1000p
C195
100p
C197
(B)
1.5
pC
194
(B)2p
C193
(B)
2pC191
(B)
2.5
p
C192
(B)2p
C198
(H0AM)4.7n
L192
LK
73H
0A
M10N
J
10n
L181
(H0AM)5.6n
L191
Q1812SC5108FT/Y/
$R
192
0
R195
$R
193
0
R194
$R
191
220
R1846
.8k
R183
10k
R182
100
R181
CN191
(B)
10p
C216(B
)10p
C217 470p
C233
470pC218 LK73H0AM12NJ
12n
L205
22R211
180
R206
180
R208
33R207
470p
C220
0.0
47u
C221
470p
CUR_ADJ
6
ENABLE
5
RF_OUT
4RF_IN3
NC2
VCC1
Pre-DRIVE
BGU6104IC202
120
R213
1k
R212
4700p
C222
C224
100p
C223
(-71)
120n
L206 8.2
kR
214
470p
C267
15p
C230
5p
C229
10p
C219
22p
C253
470p
C225
10n
L212
15n
L207LK73H0AM10NJ
10n
L209LK73H0AM15NJ
15n
L208
0
R223
$R
202
$R
201
470p
C232
100
R224
47
R216
470p
C234
Q201RD01MUS2BT513
2.7
k
R209
3.3
k
R215
DRIVE FINAL
TXL:7.3VTXH:7.1V
C231
470pC237
470p
C235
$C
254
LR
79Z
0C
A39N
G39n
L218
LB
73G
0A
M-0
04
L211
0R228
330
R218
(G)
39p
C268(G
)15p
$C
238
$C
202
$C
201
$C
242
470p
C239
Q202RD08MUS2T514
0
R266
0
R267
3.9
k
R210
3.3
k
R222
10
R219
0
R2210
R225
micro strip lineLR79G0GK9N1C
9.1n
L210
18p
C245
33p
C226
4.7
pC
236
C93-0
941-0
5
18p
C244
$C
205 1p
C203
$C
207
$C
256
$C
206
C93-0
935-0
510p
C255
9T
LR
79Z
0D
C45N
5J
L213
0R270
150p
C240
470p
C241
0.1
u
C243
LB73F0AW-002L214
ANT_SW/LPF
100p
C227 470p
C215
$C
269
L5208FD201
120n
L204
LR
79Z
0C
AR
22J
220n
L203
TX:0.8VRX:0V
(B)
3pC208
(B)1pC228
(B)
4pC251
(B)
7pC249
(B)1.5pC248
(B)1pC250
100p
C246
(B)
7p
C247
$C
204
4T
L215
4T
L217LR79Z0DD16N9J
4T
L216
TX1.7VRX:0V
(G)18p
C252
470p
C211
$C
210
5p
C209(B
)3p
C270
RN
142S
D202
RN
142S
D203
3.9nL2025T
L201
120
R204
APC
470p
C257
$R
203
100k
NC
U15W
F104F
6S
TH
201
-t
470p
C213
470p
C212
470p
C214
CE
3VSS2
VIN
4VoUT1
XC8102AA07-GIC201
1k
R205
470pC263 EMD12
Q207
8.2k
R259
470p
C266
8200p
C265
8200p
C264
Q206SSM3K15AMFV
1k
R237
3.9
k
R233
100k
R268
1k
R269
3.9
k
R260
100k
R234
VCC
8
oUT2
7
-IN2
6
+IN2
5VEE4
+IN13
-IN12
oUT11
BA3472FVM
IC203
TXL:2.2VTXH:2.8V
R92-3
756-0
5
0.0
56u
C262
470p
C261
220
R230
(D)
39k
R265
27
R251
1/3
0.2
2R2501/3
0.2
2
R248
3.3kR258
220
R257
(D)
6.8
k
R264
(D)
6.8
kR
256
(D)4.7kR252
(D)4.7kR253
(D)
39k
R255
/AP
CS
W
SSM3K15AMFVQ205
10k
R249
LTC044EEBFS8Q204
T:5.0VR:0V
50T
CE
6
VS
S
5
NC
2
4
VoU
T
3
NC
1
2
VIN
1
XC6209B502D-GIC15
100k
R47
470p
C56
2.2
uC
55
0.1
uC
54
ED
ZV
5.6
B
D204
47kR246
47
R247
27k
R244
Q203LSCR523EBFS8
C258
470p
470p
C259
47k
R245
TH
P
AN
TS
W
AP
CS
W2
AP
C
TX
C
/DS
W
Ram
p_O
ffset
TH Tap
ON Board Contact ON Board Plate
E2D-0058-00CN202
E2D-0082-00CN8
E2D-0058-00CN201
E2D-0082-00CN10
$CN205$CN204$CN203
Destination
0K-00
*R1
AGCKEEP
/DCR_RST
/DCR_CS
BCLK
RX
DCR_DO
DCR_DI
DCR_ACLK
PLD
TX
CN
305
CN
309
CN
308
CN
307
CN
306
RK74HB1J100JCP303
RK74HB1J100JCP302
680R336
680R335
1k
R332
VS
S4 53
DA_FS52
AD_FS51
AD_SDo50
AD_SCLK49
DVDD48
LD47
SDATAo46
SCLK45
SDATAI44
CSN43
AGC_KEEP42
TX_PDN41
RX_PDN40
RS
TN
39
VC
oM
_A
D
38
AD
VD
D
37
AD
VS
S
36
TE
ST
2
35
AoU
T_N
34
AoU
T_P
33
RX
VD
D
32
BIA
S1
31
LN
AV
DD
30
LN
AC
oN
T
29
LN
AIN
28
VS
S3
27
VSS2 26
LNAoUT 25
DEMVDD 24
DEMIN 23
VSS1 22
LoVDD 21
RFoUTN 20
RFoUTP 19
LoIN 18
LoDVDD 17
CPZ 16
SWIN 15
CP 14
CP
VD
D
13
SY
NV
DD
12
SY
NV
SS
11
VR
EF
2
10
TC
XoIN
9
VR
EF
1
8
DA
CV
DD
7
SM
FoU
T
6
BIA
S2
5
TE
ST
1
4
DA
_S
DI
3
DV
SS
2
DA
_S
CLK
1
AK2401
IC303
3.2V
470p
C338
10u
C333
0.1
u
C321
100p
C322
0
R333
CN
303
CN
304
(D)
47k
R3252
.2u
C301 1u
C304 (B)4pC312
LR79G0CQ3N9C
3.9nL310
LR79G0CQ22NG
22nL309
820
R303
820
R304
5.6R312
390
LR
79G
0C
Q39N
G
39n
L311
1000p
C3130.01u
C314
1uC315
R310
RX HPF
(B)5p
C309
(B)10p
C308
(B)5p
C310
(B)8p
C334
470p
C306
1S
S390
D304
1S
S390
D303
LR
79G
0C
Q12N
G
12n
L307
LR
79G
0C
Q10N
G
10n
L302
LR
79G
0C
Q7N
5C
7.5
nL308
$R305
(B)1.5p
C317
6p
C319
(G)15pC320
(B)4p
C311
LR
79G
0C
Q39N
G39n
L313
LR
79G
0C
Q39N
G39n
L312
LR
79G
0C
Q22N
G22n
L314
LR
79G
0C
QR
22G
220n
L315
12
R315
470
R316
470
R314
100p
C323
0.01u
C324 (-71)
270nL303
(B)
3pC302
100
R302
100
R301
100p
C325 LK
73H
0A
M33N
J33n
L304
(B)
2pC305
0.01u
C326
(-71)
33nL301
100
R313
10u
C316
1000p
C346
10
1uC345
100pC330
0.1uC329
0.1uC327
100pC328
0
R331
(D)
27k
R330 0.4
7u
C343
10u
C342
100p
C341
AN
TC
HK
FE
M_A
LM
FE
M_P
WR
CP
VC
O_M
OD
VO
L
SD
ET
TH
PT
EM
P
BA
TT
Ram
p_O
ffset
CV
CP
Z
PFKEY
100*4
CP
403
10*4CP402
(D)100k
R463
(D)10k
R464
8.2k
R617
0.1u
C500
100*4
CP405100*4
CP404
+VA232
REFP31
REFM30
GPIo29
+VBD28
BDGND27
SDo26
SDI25
SC
LK
24
CS
23
AG
ND
2
22
+V
A1
21
CH
0
20
CH
1
19
CH
2
18
CH
3
17
CH4 16
CH5 15
CH6 14
CH7 13
CH8 12
CH9 11
CH10 10
CH119
CH
12
8
CH
13
7
CH
14
6
CH
15
5
AIN
M
4
AIN
P
3M
Xo
2A
GN
D1
1
ADS7961SRHBIC409
100
R469
100
R470
$R459
$R460100
R467
100
R468
$C
495
$C
494
CN453
0
R466
0R462
0
R461
1u
C496 0
.1u
C498
0.1
u
C499
0.1u
C497
/ADC_INT
SDI0SDO0SCK0/ADC
8bit/16ch ADC
82k
R227
SP
C10501A
01
D206
Side2
EMG
Side1
PTT
100p
C67
100p
C68
6
5
4
3
2
1
E40-6883-05CN7
100p
C70
100p
C69
/EM
G/S
IDE
2/S
IDE
1/IN
T_P
TT
RK74HB1J101JCP1
5.4V
BLS
0.5A
50A
$C
605
25
4.7
u
C604
F1B-0085-00E601
CN
6
VDD
8
oUT2
7
IN2-
6
IN2+
5VSS4
IN1+3
IN1-2
oUT11
BU7442NUXIC18
RK73PB2H1R2J
1.2
R656
(D)
47k
R50
(D)
47kR51
(D)
22k
R58
(D)
18k
R57
68k
R650
470
R60 3
.3k
R56
10k
R652
470
R654
0
R59
LTC014EEBFS8Q6
FZA10BH-R50F2
470p
C66
1u
C674
25
4.7
u
C676
1000p
C650
.1u
C64
0.1
u
C62
0.1
u
C63
Q72SB1132(Q,R)
BLS
25REF32A
50A
F1B-0083-00E301
12bit/4ch DAC
AS
SIS
T
SD
O1
SC
K1
/DA
CC
S
AP
C
FC
NT
10*4
CP406CN454
SCLK10
SYNC9
DIN
8
VREFIN
7
GND
6 VoUTD 5
VoUTC 4
VoUTB 3
VoUTA
2
VA
1
DAC124S085CIS
IC410
1u
C501
0.1
u
C502
32M
DCR_DDO
DCR_ADI
/DCR_ACS
/DCR_DCS
RK74HB1J100JCP301
CN
311
CN
310
0.1uC332
100pC331
0.0
1u
C303
1.8V
32M
18M
DA
TA
[0]
DB
[6]
DB
[4]
DB
[2]
DB
[0]
WR
0_/W
RLC
D_A
0D
B[7
]D
B[5
]
DB
[3]
DB
[1]
WR
1_/O
ELC
D_/C
S
LC
D_B
LC
/WR
AD
D[2
3]
DA
TA
[4]
DA
TA
[5]
/OE
/CS
4
DA
TA
[1]
DA
TA
[3]
LC
D_R
ST
DA
TA
[7]
DA
TA
[2]
DA
TA
[6]
100
R479 L430
L431
100
R480
RK
74H
B1J101J
CP
411
LB
73H
0A
V-0
02
L428
RK
74H
B1J101J
CP
410
LB
73H
0A
V-0
02
L427
CN
452
L429
RK
74H
B1J101J
CP
412
USB_VBUS
USB0_DM
USB0_DP
USB_SW
CN460
CN458
CN457
CN456
LC
D_B
LC
LC
D_D
B7
LC
D_D
B6
LC
D_D
B5
LC
D_D
B4
LC
D_D
B3
LC
D_D
B2
LC
D_D
B1
LC
D_D
B0
LC
D_/R
ST
LC
D_R
/W(W
R0)
LC
D_E
(WR
1)
32LC
D
32LC
D
18M
LC
D_V
SS
LC
D_/C
S
LC
D_A
0
LB
C_B
LB
C_R
LB
C_G
LE
D_G
KE
Yo0
LE
D_R
KE
Yo1
LE
D_B
GN
D
KE
Yo2
KE
Yo3
GN
D
KE
Yi0
KE
Yi1
KE
Yi2
KE
Yi3
KE
Yi4
ME
MIC
50A
50A
GN
D
GN
D
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EC720BP-0341ACN402
3.2V
DB
[7]
DB
[6]
DB
[5]
DB
[4]
DB
[3]
DB
[2]
DB
[1]
DB
[0]
WR
0_/W
R
LC
D_A
0
LC
D_/C
S
WR
1_/O
E
0.1
uC
518
0.1
uC
517
32M
50A
KE
Y_IN
T
/KE
YI4
/KE
YI3
/KE
YI2
/KE
YI1
/KE
YI0
LE
D_B
LE
D_G
LE
D_R
LB
C_R
LB
C_B
LB
C_G
KE
YO
1K
EY
O2
KE
YO
3
KE
YO
0100k
R41510k
R411
LTC044EEBFS8Q402
1SS400SM
D4071SS400SM
D4061SS400SM
D4051SS400SM
D4041SS400SM
D403
RK
74H
B1J101J
CP
414
RK
74H
B1J101J
CP
408
RK
74H
B1J101J
CP
409
RK
74H
B1J101J
CP
413
5.0V
470p
C470
470p
C510
0.1
uC
516
470p
C469
470p
C515
470p
C471
470p
C472
470p
C473
470p
C476
470p
C475
470p
C474
470p
C477
5.0V50A
32M
32M
CE
6
VS
S
5
NC
2
4
VoU
T
3
NC
1
2
VIN
1
XC6209B502D-GIC17
2.2
uC
60
0.1
u
C672
MOTION SENSOR
SD
A10
SCL 9
ADD 8
INT 7
RSVD 6
VD
D5
GND4
DNC23
DNC12
IoVDD1
KXCJ9-1008IC406
4.7
kR
449
10
R446
0.0
1u
C453
0.1uC454
I2CCK
I2CDT
2.2
k
R447
2.2
k
R448
1.2V
3.2V
12M
32M
EXTM_M
ME
0R604
0R639
0R638
$D
608
1k
R635
2.2
k
R609
4.7
uC
663
101u
C606
1u
C607
0.1
uC
601
$R
611
RB521CM-30
D609
2.2
k
R610
1k
R608
$R
607
$C
660
4.7
uC
659
101uC612
$C614
470R605
$R606
$D
607
$D
606
$D
605
3.2V
R637
0
R636
4.7u
C603
CN623
CN624
SPKVDD
18M
4.7
u
C621 2
.2u
C608
2.2
uC
610
4.7
u
C602
LB73G0AM-004
L601
LB73G0AM-004L613
4.7
u
C615
1.8V 18M
LB
73G
0A
M-0
04
L612
XToG7
MCLK/XTIG6
CLKoUT5G5
CLKoUT2/GPIo2G4
DBVDDG3
DCVDDG2 DGND
G1IN1R
F7
VMIDC
F6
IN4R
F5 IN2
R
F4
CS
/GP
Io6
F3
AD
CD
AT
F2
BC
LK
F1
IN1
L
E7
LD
oV
DD
E6
IN4
L
E5
IN2
L
E4
oS
CE
NA
/GP
Io5
E3
DA
CD
AT
E2
LR
CL
K
E1
AG
ND
D7
AV
DD
D6
IN3L
D5
IN3R
D4
CIFMoDE
D3
SDA
D2
SCLK D1
CPGND C7
CPVDD C6
HPoUT1L C5
HPoUT2L C4
SPKoUTLN
C3
SPKoUTRN
C2
SPKGND2
C1
CPCB
B7
CP
CA
B6
HP
oU
T1
R
B5
HP
oU
T2
R
B4
SP
Ko
UT
LP
B3
SP
Ko
UT
RP
B2
SP
KV
DD
2
B1
CP
Vo
UT
N
A7
CP
Vo
UT
P
A6
HP
oU
TF
B
A5
MIC
BIA
S
A4
MIC
VD
D
A3
SP
KV
DD
1
A2
SP
KG
ND
1
A1
IC601
4.7u
C609
2.2
u
C622
1.8V
18M
I2C
CK
I2C
DT
/CIN
T
WC
LK
CO
DE
C_D
OB
CLK
CO
DE
C_D
I
100
R602
100
R601
10
(CO
DE
C)
CP
601
10k
L610
0.0
1u
C626
4.7
u
C620
5.0V
+B
50J
PT
T/R
XD
EX
TM
_M
LB73H0AV-002L635
470p
C693
220p
C690
47p
C689
CE
6
VS
S
5
NC
2
4
VoU
T
3
NC
1
2
VIN
1
XC6209B502D-GIC651
2.2
u
C691
0.1
u
C692
CN
650
220p
C684
(RXD)SHIFTLEVEL
32M50A
CONTROL TXSLOT =>
(EXTPTT) DC SW
(TXD)SHIFTLEVEL
EX
TM
IC_
SW
RX
D1
/EX
T_P
TT CN652
10k
R685
VCC
5
oUTY
4GND3
INA2
G1
TC7SET125FUFIC652
VCC
5
oUTY
4 GND 3
INA 2
INB 1
TC7SZ08FEIC654
470p
C695
0.01uC697
RE1C001UNQ6562
.7k
R681
0.01u
C698
1k
R661
5V
C
EX
TS
PD
ET
/OP
TD
ET
1u
C688
220k
R682100
R663RB706F-40-MC
D650
/TX
D1_JK
_E
N
TX
D1
0.1u
C673
LTC044EEBFS8Q654
220p
C677
LTC014EEBFS8Q653
ED
ZV
6.8
BD
620
0.3
3u
C627
100p
C658
CN
604
100p
C657
LB73G0AM-004L622
LB73G0AM-004L623
CN
605
LB73G0AM-004
L605
10u
L609
100p
C617
LB73G0AM-004L604
0.3
3u
C625
D621
10u
L608
100p
C618
0.1u
C683
560
R659
FZA10BH-R315F650
47k
R658
Q6502SB1694 PoUT 1
0
PW-GND
9
PRE-GND
8
PHASE
7
NF
6RIPPLE5
VIN4
NC23
VCC2
NC11
TA7368FGIC650
C669
R653
100p
C681
1u
C686
0R672
2.2
u
C667
0.1
u
C687
22
R670 2.7
k
R684
10kR683
1.5k
R651
22u
100
TXD
SPO
OPTDET
AE
2P
IN J
AC
K C
ON
NE
CT
OR
50J
PTT/RXDMICIN
TX
D
EXTSPDETNC
NC
AVRM10120MAABD655
E1B-0020-00J652
E1B-0019-00J651
6.347u
C664
6.347uC675
SPC10501A01
D653
D654
D652
ED
ZV
6.8
BD
651
330k
R665
270k
R664
47k
R678
470k
R657
27kR676
0.0
68u
C671
10k
R655
Q652
SS
M3K
324R
F
Q651SSM3K324RF
680
R668
220p
C679
$C
665
CN
651
220k
R667
470
R680
50A18M
32C
1.8V
2
1
E41-1476-05
CN602
$C
307
470pC344
1S
S400S
M
D302
1S
S400S
M
D301$
L305
TO DISPLAY UNITXC1-209 A/2CN202
TO DISPLAY UNITXC1-209 B/2 CN301
TX-RX UNIT (XC1-180K-00 (NX-3320))
A
1
B C D E F G
2
3
4
5
6
7
8
9
10
H I J K L M N O P Q(No.RA053<Rev.001>) 2-18
PARTS LIST
[NX-3220,NX-3320]
* SAFETY PRECAUTION Parts identified by the � symbol are critical for safety. Replace only with specified part numbers.
* BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance. We recommend that genuine parts be used.
* (x_) in a description column shows the number of the used part.
- Contents - Exploded view of general assembly and parts list Electrical parts list Packing materials and accessories parts list
3-2 3-53-19
(No.RA053<Rev.001>)3-1
Exploded view of general assembly and parts list
X3
X7
Block No.M1MM
TX-RX UNIT<01><02>
DISPLAY UNIT<03>
61
A
44
46
45
43
2
2
4
9
7
3
6
8
11
12
13
14
16
20
19
18
21
22
23
24
24
2526
28
29
30
31
32
33 34
35
36
3738
39
40
41
49 49
5050
51
52
53
41
55
54
57
60
62
64
65
66
62
67
68
70
71
72
73
74
75
77
78
79
B
C
DE
F
G
F
F
10
3-2(No.RA053<Rev.001>)
General assemblyBlock No. [M][1][M][M]
Symbol No. Part No. Part Name Description Local
2 A0C-0177-00 P.CABINET ASSY BASIC 2PIN 3220K,3220E3,3320K,3320E3 2 A0C-0178-00 P.CABINET ASSY STD 2PIN 3220K2,3220E2,3320K2,3320E2 2 A0C-0179-00 P.CABINET ASSY FULL 2PIN 3220K3,3220E,3320K3,3320E 3 A8A-0050-00 REAR PANEL 4 A1A-0105-00 CHASSIS 2PIN 6 B3H-0062-00 LCD ASSY 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 7 B4B-0006-00 CAUTION STICKER FCC 3220K,3220K2,3220K3,3320K,3320K2,3320K3 7 B4C-0545-10 STANDARD LABEL ADDRESS 3220E,3220E2,3220E3,3320E,3320E2,3320E3 8 B42-7417-04 STICKER NEXEDGE 9 B4D-0044-00 KENWOOD BADGE 10 D32-0454-04 STOPPER CH KNOB 3220K,3220E3,3320K,3320E3 11 D3C-0003-00 STOPPER NUT 12 E04-0467-15 C.RECEPTACLE-SM SMA 13 E2D-0083-00 TERMINAL ANT 14 E3K-0275-00 LEAD.WIRE W.C. SP 16 E7C-0018-00 TERMINAL BLOCK BATT 18 F10-3227-05 SHIELDING COVER BLS/GPS 19 F1B-0084-00 SHIELDING COVER BLS/AK2401 20 F1B-0086-00 SHIELDING COVER BLS/CODEC 21 F1B-0088-00 SHIELDING COVER BLS/OMAP 22 B1B-0105-00 ILL.GUIDE LCD 23 J2B-0350-10 MOUNTING LCD 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 24 G0K-0012-00 KNOB SPRING (x2) 25 B1B-0110-00 REF.SHEET LCD 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 26 B1B-0138-00 FILTER LCD 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 28 G1A-0057-00 FIBROUS SHEET ECM 29 G1A-0063-00 FIBROUS SHEET AIR LEAK GORE 30 G1A-0053-00 FIBROUS SHEET SP 31 G1G-0075-00 SHEET PTT 32 G1G-0076-00 SHEET KEY 33 G1G-0077-00 SHEET SP/BT/GPS 34 G1B-0266-00 RUBBER SHEET SP 35 G1G-0080-00 SHEET KEY 4DIRECTIONS 3220K2,3220E2,3320K2,3320E2 36 G1B-0240-00 SEAL VOID 37 G11-4090-14 SHEET FINAL 38 G11-4440-04 SHEET LEAK COVER 39 G1D-0203-00 CUSHION SP/ECM 40 G1D-0204-00 CUSHION AIR LEAK 41 G1D-0205-00 CUSHION LCD(x2) 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 43 G13-2102-34 CONDUCT CUSHION BLS COVER 3320K,3320K2,3320K3,3320E,3320E2,3320E3 44 G13-2220-04 CUSHION ANT 45 G1B-0300-00 SHEET LCD 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 46 G1D-0272-00 CUSHION TX-RX PCB 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2 49 G53-1792-04 PACKING O RING-NUT(x2) 50 G53-2211-04 O RING VOL/CH(x2) 51 G5D-0133-00 PACKING ANT 52 G5D-0121-00 PACKING HOLDER 53 G5D-0122-00 PACKING ECM 54 G5D-0120-00 PACKING TOP 55 G5D-0128-00 PACKING TER.BLOCK/RING(x2) 57 G5D-0124-00 PACKING 2PIN 60 J1K-0493-00 HOLDER SP/LCD/KEY 61 J1K-0494-10 HOLDER 62 K2K-0248-00 KEY TOP FULL 3220K3,3220E,3320K3,3320E 62 K2K-0247-00 KEY TOP STD 3220K2,3220E2,3320K2,3320E2 64 J87-0027-15 FPC(LEAD FREE) PTT 65 J8C-0020-00 FLEX P.BOARD VOL/ROSW 66 J8C-0022-00 FLEX P.BOARD KEY-MAIN 67 K2K-0249-00 KNOB VOL 68 K2K-0250-00 KNOB ROSW 70 K2K-0251-00 KNOB PTT 71 K2K-0252-00 BUTTON KNOB PTT 72 S6A-0004-00 ROTARY SWITCH 73 T0H-0025-10 SPEAKER D28 74 T9A-0058-00 ANTENNA ELEMENT GPS 75 T9A-0059-00 ANTENNA ELEMENT BT 77 W09-0971-05 LITHIUM CELL 78 R31-0692-15 V RESISTOR 79 J2B-0366-00 REINFORCE MOUNT A N09-6554-05 PAN HEAD SCREW SMA(x2) B N79-2080-43 P.HEAD T.SCREW (x2) C N09-6646-05 SPECIAL SCREW CASE(x2) D N14-1011-00 CIRCULAR NUT VOL E N14-1012-00 CIRCULAR NUT ROSW F N83-2005-48 P.HEAD T.SCREW UNIT(x11) G N84-2004-43 P.HEAD T.SCREW TER.BLOCK (+,-)(x2)- XCA-029K-00 TX-RX UNIT SERVICE UNIT 3220K,3220K2,3220K3- XCA-029E-01 TX-RX UNIT SERVICE UNIT 3220E,3220E2,3220E3- XCA-030K-00 TX-RX UNIT SERVICE UNIT 3320K,3320K2,3320K3
(No.RA053<Rev.001>)3-3
- XCA-030E-01 TX-RX UNIT SERVICE UNIT 3320E,3320E2,3320E3- XC1-209K-00 DISPLAY UNIT BASIC 3220K,3220E3,3320K,3320E3- XC1-209K-01 DISPLAY UNIT STD 3220K2,3220E2,3320K2,3320E2- XC1-209K-02 DISPLAY UNIT FULL 3220K3,3220E,3320K3,3320E
Symbol No. Part No. Part Name Description Local
3-4(No.RA053<Rev.001>)
Electrical parts listTX-RX UNIT
XC1-178K-00 (NX-3220(K),NX-3220(K2),NX-3220(K3),NX-3220(E),NX-3220(E2),NX-3220(E3))*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][1]
Symbol No. Part No. Part Name Description Local
IC1 XC61CC5602N-G ICIC2 LXDC2XQ12A-252 ICIC3 TPS62140RGT ICIC4 LXDC2HN18F163 ICIC5 ------------ IC *NoteIC6 XC6209B502D-G ICIC7 ------------ IC *NoteIC8 BU18TD2WNVX ICIC9 XC6209B312D-G ICIC10 XC6215B122N-G ICIC11 NJM2878F4-32 ICIC12 XC8102AA07-G ICIC13 TPS61041DRVR ICIC14 ------------ IC *NoteIC15 XC6209B502D-G ICIC17 XC6209B502D-G ICIC18 BU7442NUX ICIC101 OPA170AIDRLR ICIC102 BU7295HFV ICIC201 XC8102AA07-G ICIC202 BGU6104 ICIC203 BA3472FVM ICIC303 ------------ IC *NoteIC351 ------------ IC *NoteIC352 74AVC4TD245GU ICIC353 74AVC4TD245GU ICIC401 ------------ IC *NoteIC402 ------------ IC *NoteIC403 S-80135ANPF-G ICIC404 ------------ IC *NoteIC405 TC7SZ08FE ICIC406 KXCJ9-1008 ICIC409 ADS7961SRHB ICIC410 DAC124S085CIS ICIC601 ------------ IC *NoteIC650 TA7368FG ICIC651 XC6209B502D-G ICIC652 TC7SET125FUF ICIC654 TC7SZ08FE IC
Q1 EMD12 DIGI TRANSISTORQ2 SSM6N15AFEM DUAL FETQ3 SSM6N15AFEM DUAL FETQ4 VT6M1 FETQ5 VT6M1 FETQ6 LTC014EEBFS8 DIGI TRANSISTORQ7 2SB1132(Q,R) TRANSISTORQ102 EM6M2 FETQ103 VT6M1 FETQ113 2SD2654/W/ TRANSISTORQ114 VT6M1 FETQ131 MCH3914-H/8/ FETQ151 2SC5108FT/Y/ TRANSISTORQ181 2SC5108FT/Y/ TRANSISTORQ201 RD01MUS2BT513 FETQ202 RD07MUS2BT514 FETQ203 LSCR523EBFS8 TRANSISTORQ204 LTC044EEBFS8 DIGI TRANSISTORQ205 SSM3K15AMFV FETQ206 SSM3K15AMFV FETQ207 EMD12 DIGI TRANSISTORQ351 SSM3K15AMFV FETQ401 2SC4617/S/ TRANSISTORQ402 LTC044EEBFS8 DIGI TRANSISTORQ650 2SB1694 TRANSISTORQ651 SSM3K324RF FET
Q652 SSM3K324RF FETQ653 LTC014EEBFS8 DIGI TRANSISTORQ654 LTC044EEBFS8 DIGI TRANSISTORQ656 RE1C001UN DIGI TRANSISTOR
D1 RR1LAM4S DIODED8 DAN222 DIODE ARRAYD9 RB520SM-30 DIODED10 RB561VM-40 SCHOTTKY DIODED102 EDZV8.2B ZENER DIODED111 1SS400SM DIODED131 SMV1251-079LF VARI CAP DIODED132 SMV1801-079LF VARI CAP DIODED133 SMV1801-079LF VARI CAP DIODED134 SMV1801-079LF VARI CAP DIODED135 SMV1801-079LF VARI CAP DIODED136 SMV1130-079LF VARI CAP DIODED201 RN142S DIODED202 RN142S DIODED203 RN142S DIODED204 EDZV5.6B ZENER DIODED205 RN142S DIODED301 1SS400SM DIODED302 1SS400SM DIODED303 1SS390 DIODED304 1SS390 DIODED401 RB521CM-30 DIODED402 RB521CM-30 DIODED403 1SS400SM DIODED404 1SS400SM DIODED405 1SS400SM DIODED406 1SS400SM DIODED407 1SS400SM DIODED609 RB521CM-30 DIODED620 EDZV6.8B ZENER DIODED621 EDZV6.8B ZENER DIODED650 RB706F-40-MC DIODED651 EDZV6.8B ZENER DIODED652 EDZV6.8B ZENER DIODED653 SPC10501A01 VARISTORD654 SPC10501A01 VARISTORD655 AVRM10120MAAB VARISTOR
C1 CK73HBB1H102K C CAPACITOR 1000pF 50V KC2 CC73HCH1H220G C CAPACITOR 22pF 50V GC3 CK73HBB1H682K C CAPACITOR 6800pF 50V KC4 C93-1967-05 C CAPACITOR 470pF 50VC5 C93-1967-05 C CAPACITOR 470pF 50VC6 C93-1967-05 C CAPACITOR 470pF 50VC7 C93-1967-05 C CAPACITOR 470pF 50VC8 C93-1967-05 C CAPACITOR 470pF 50VC9 CK73HBB1H682K C CAPACITOR 6800pF 50V KC10 C93-1967-05 C CAPACITOR 470pF 50VC14 C93-1967-05 C CAPACITOR 470pF 50VC15 CK73HB1A224K C CAPACITOR 0.22uF 10V KC16 CK73HB1A224K C CAPACITOR 0.22uF 10V KC17 CK73HBB1H471K C CAPACITOR 470pF 50V KC18 CK73FB1C106K C CAPACITOR 10uF 16V KC19 CK73FB1C106K C CAPACITOR 10uF 16V KC20 CK73HBB1H332K C CAPACITOR 3300pF 50V KC21 CK73HB1E104K C CAPACITOR 0.10uF 25V KC22 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC23 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC24 CK73GB0J106K C CAPACITOR 10uF 6.3V KC25 CK73HB1A474K C CAPACITOR 0.47uF 10V KC26 CK73HB1A474K C CAPACITOR 0.47uF 10V KC27 CK73GB1E104K C CAPACITOR 0.1uF 25V KC28 C93-1967-05 C CAPACITOR 470pF 50VC29 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC30 CK73HBB1H471K C CAPACITOR 470pF 50V KC31 CK73FB1C106K C CAPACITOR 10uF 16V KC32 CK73GB0J106K C CAPACITOR 10uF 6.3V KC33 CK73HB1A224K C CAPACITOR 0.22uF 10V KC34 CK73HB1A224K C CAPACITOR 0.22uF 10V KC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 C93-1967-05 C CAPACITOR 470pF 50V
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-5
C37 C93-1967-05 C CAPACITOR 470pF 50VC38 CK73GB1E104K C CAPACITOR 0.1uF 25V KC39 CK73GB1E105K C CAPACITOR 1uF 25V KC40 CK73HB1E104K C CAPACITOR 0.10uF 25V KC41 CK73HB1E104K C CAPACITOR 0.10uF 25V KC42 CK73HB1E104K C CAPACITOR 0.10uF 25V KC43 CK73HB1A474K C CAPACITOR 0.47uF 10V KC44 CK73HB1E104K C CAPACITOR 0.10uF 25V KC46 CK73GB1A335K C CAPACITOR 3.3uF 10V KC47 CK73GB1A335K C CAPACITOR 3.3uF 10V KC48 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC49 CK73HBB1H681K C CAPACITOR 680pF 50V KC50 CK730JM1H684K C CAPACITOR 0.68uF 50V KC51 CK73HB1A224K C CAPACITOR 0.22uF 10V KC52 CK73HBB1H681K C CAPACITOR 680pF 50V KC53 CK73HB1A224K C CAPACITOR 0.22uF 10V KC54 CK73GB1E104K C CAPACITOR 0.1uF 25V KC55 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC56 CK73HBB1H102K C CAPACITOR 1000pF 50V KC60 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC62 C93-1959-05 C CAPACITOR 0.1uF 16VC63 C93-1959-05 C CAPACITOR 0.1uF 16VC64 C93-1959-05 C CAPACITOR 0.1uF 16VC65 CK73HBB1H102K C CAPACITOR 1000pF 50V KC66 CK73HBB1H471K C CAPACITOR 470pF 50V KC67 CC73JCH1H101J C CAPACITOR 100pF 50V JC68 CC73JCH1H101J C CAPACITOR 100pF 50V JC69 CC73JCH1H101J C CAPACITOR 100pF 50V JC70 CC73JCH1H101J C CAPACITOR 100pF 50V JC102 CK73HB1H103K C CAPACITOR 10000pF 50V KC103 CC73HCH1H330G C CAPACITOR 33pF 50V GC104 CC73JCH1H101J C CAPACITOR 100pF 50V JC105 CK73GB1H105K C CAPACITOR 1uF 50V KC106 C93-1959-05 C CAPACITOR 0.1uF 16VC107 CC73JCH1H101J C CAPACITOR 100pF 50V JC108 CC730AD1H104J C CAPACITOR 0.1uF 50V JC111 CK73HBB1H471K C CAPACITOR 470pF 50V KC112 CS77BP1A4R7M TA E CAPACITOR 4.7uF 10V MC121 CK73FBB1H154K C CAPACITOR 0.15uF 50V KC122 CS77ABE1D100M TA E CAPACITOR 10uF 20V MC123 CK73FB1H473K C CAPACITOR 0.047uF 50V KC132 CK73HBB1H471K C CAPACITOR 470pF 50V KC133 CK73HBB1H102K C CAPACITOR 1000pF 50V KC134 CK73HBB1H102K C CAPACITOR 1000pF 50V KC135 CK73HBB1H471K C CAPACITOR 470pF 50V KC137 CC73HCH1H030B C CAPACITOR 3pF 50V BC138 CC73HCH1HR75B C CAPACITOR 0.75pF 50V BC139 CC73HCH1H080B C CAPACITOR 8pF 50V BC140 CC73HCH1H070B C CAPACITOR 7pF 50V BC141 CC73HCH1H090B C CAPACITOR 9pF 50V BC142 CK73HBB1H471K C CAPACITOR 470pF 50V KC144 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC145 CK73HBB1H471K C CAPACITOR 470pF 50V KC146 CC73HCH1H060B C CAPACITOR 6pF 50V BC147 CK73HBB1H471K C CAPACITOR 470pF 50V KC181 CK73HBB1H471K C CAPACITOR 470pF 50V KC182 CK73HBB1H471K C CAPACITOR 470pF 50V KC183 CC73HCH1H040B C CAPACITOR 4pF 50V BC191 CC73HCH1H060B C CAPACITOR 6pF 50V BC192 CC73HCH1H120G C CAPACITOR 12pF 50V GC193 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC194 CC73HCH1H060B C CAPACITOR 6pF 50V BC195 CK73HBB1H102K C CAPACITOR 1000pF 50V KC197 CK73HBB1H471K C CAPACITOR 470pF 50V KC198 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC202 CC73GCH1H120G C CAPACITOR 12pF 50V GC203 CC73GCH1H020B C CAPACITOR 2pF 50V BC204 CC73GCH1H090B C CAPACITOR 9pF 50V BC205 CC73GCH1H150G C CAPACITOR 15pF 50V GC206 CC73GCH1H470G C CAPACITOR 47pF 50V GC207 CC73GCH1H220G C CAPACITOR 22pF 50V GC209 CC73HCH1H150G C CAPACITOR 15pF 50V GC211 CK73HBB1H102K C CAPACITOR 1000pF 50V KC212 CK73HBB1H102K C CAPACITOR 1000pF 50V KC213 CK73HBB1H102K C CAPACITOR 1000pF 50V KC214 CK73HBB1H102K C CAPACITOR 1000pF 50V KC218 CK73HBB1H102K C CAPACITOR 1000pF 50V KC220 CK73HBB1H102K C CAPACITOR 1000pF 50V K
Symbol No. Part No. Part Name Description Local
C221 CK73HB1E473K C CAPACITOR 0.047uF 25V KC222 CK73HBB1H472K C CAPACITOR 4700pF 50V KC223 CC73HCH1H101J C CAPACITOR 100pF 50V JC224 CK73HBB1H102K C CAPACITOR 1000pF 50V KC225 CK73HBB1H102K C CAPACITOR 1000pF 50V KC226 CC73GCH1H100B C CAPACITOR 10pF 50V BC227 CC73GCH1H391J C CAPACITOR 390pF 50V JC228 CC73GCH1H060B C CAPACITOR 6pF 50V BC233 CC73HCH1H680J C CAPACITOR 68pF 50V JC234 CK73HBB1H102K C CAPACITOR 1000pF 50V KC235 CK73HBB1H102K C CAPACITOR 1000pF 50V KC237 CK73HBB1H102K C CAPACITOR 1000pF 50V KC238 CC73GCH1H151J C CAPACITOR 150pF 50V JC239 CK73HBB1H102K C CAPACITOR 1000pF 50V KC240 CK73HB1E104K C CAPACITOR 0.10uF 25V KC241 CK73HBB1H102K C CAPACITOR 1000pF 50V KC246 CC73GCH1H102J C CAPACITOR 1000pF 50V JC247 CC73GCH1H180G C CAPACITOR 18pF 50V GC248 CC73GCH1H090B C CAPACITOR 9pF 50V BC249 CC73GCH1H150G C CAPACITOR 15pF 50V GC250 CC73GCH1H040B C CAPACITOR 4pF 50V BC251 CC73GCH1H080B C CAPACITOR 8pF 50V BC252 CC73HCH1H270G C CAPACITOR 27pF 50V GC253 CC73HCH1H180J C CAPACITOR 18pF 50V JC255 CC73GCH1H030B C CAPACITOR 3pF 50V BC257 CK73HBB1H102K C CAPACITOR 1000pF 50V KC258 C93-1969-05 C CAPACITOR 1000pF 50VC259 C93-1969-05 C CAPACITOR 1000pF 50VC260 CK73HBB1H102K C CAPACITOR 1000pF 50V KC261 CK73HBB1H102K C CAPACITOR 1000pF 50V KC262 CK73GB1C563K C CAPACITOR 0.056uF 16V KC263 CK73HBB1H102K C CAPACITOR 1000pF 50V KC264 CK73HB1H822K C CAPACITOR 8200pF 50V KC265 CK73HB1H822K C CAPACITOR 8200pF 50V KC266 C93-1969-05 C CAPACITOR 1000pF 50VC269 CC73GCH1H180G C CAPACITOR 18pF 50V GC301 CK73HB0J225K C CAPACITOR 2.2uF 6.3V KC302 CC73HCH1H030B C CAPACITOR 3pF 50V BC303 CK73HB1H103K C CAPACITOR 10000pF 50V KC304 CK73HB1A105K C CAPACITOR 1uF 10V KC305 CC73HCH1H020B C CAPACITOR 2pF 50V BC306 CK73HBB1H102K C CAPACITOR 1000pF 50V KC307 CC73HCH1H030B C CAPACITOR 3pF 50V BC308 CC73HCH1H270J C CAPACITOR 27pF 50V JC309 CC73HCH1H150G C CAPACITOR 15pF 50V GC310 CC73HCH1H150G C CAPACITOR 15pF 50V GC311 CC73HCH1H150G C CAPACITOR 15pF 50V GC312 CC73HCH1H120G C CAPACITOR 12pF 50V GC313 CK73HBB1H102K C CAPACITOR 1000pF 50V KC314 CK73HB1H103K C CAPACITOR 10000pF 50V KC315 CK73HB1A105K C CAPACITOR 1uF 10V KC316 CK730BS0J106M C CAPACITOR 10uF 6.3V MC317 CC73HCH1H030B C CAPACITOR 3pF 50V BC319 CC73HCH1H040B C CAPACITOR 4pF 50V BC320 CC73HCH1H390G C CAPACITOR 39pF 50V GC321 CK73HB1E104K C CAPACITOR 0.10uF 25V KC322 CK73HBB1H102K C CAPACITOR 1000pF 50V KC323 CK73HBB1H102K C CAPACITOR 1000pF 50V KC324 CK73HB1H103K C CAPACITOR 10000pF 50V KC325 CK73HBB1H102K C CAPACITOR 1000pF 50V KC326 CK73HB1H103K C CAPACITOR 10000pF 50V KC327 CK73HB1E104K C CAPACITOR 0.10uF 25V KC328 CK73HBB1H102K C CAPACITOR 1000pF 50V KC329 CK73HB1E104K C CAPACITOR 0.10uF 25V KC330 CK73HBB1H102K C CAPACITOR 1000pF 50V KC331 CK73HBB1H102K C CAPACITOR 1000pF 50V KC332 CK73HB1E104K C CAPACITOR 0.10uF 25V KC333 CK730BS0J106M C CAPACITOR 10uF 6.3V MC334 CC73HCH1H390G C CAPACITOR 39pF 50V GC338 CK73HBB1H102K C CAPACITOR 1000pF 50V KC341 CK73HBB1H102K C CAPACITOR 1000pF 50V KC342 CK730BS0J106M C CAPACITOR 10uF 6.3V MC343 CK73HB1A474K C CAPACITOR 0.47uF 10V KC344 CK73HBB1H102K C CAPACITOR 1000pF 50V KC345 CK73HB1A105K C CAPACITOR 1uF 10V KC346 CK73HBB1H102K C CAPACITOR 1000pF 50V KC354 CC73HCH1H040B C CAPACITOR 4pF 50V BC356 C93-1953-05 C CAPACITOR 0.01uF 25V
Symbol No. Part No. Part Name Description Local
3-6(No.RA053<Rev.001>)
C357 CK73HB1A105K C CAPACITOR 1uF 10V KC358 C93-1959-05 C CAPACITOR 0.1uF 16VC359 C93-1959-05 C CAPACITOR 0.1uF 16VC360 C93-1959-05 C CAPACITOR 0.1uF 16VC361 C93-1959-05 C CAPACITOR 0.1uF 16VC363 CC73HCH1H180G C CAPACITOR 18pF 50V GC364 CK73HB1A105K C CAPACITOR 1uF 10V KC365 CK73HB1A105K C CAPACITOR 1uF 10V KC366 C93-1959-05 C CAPACITOR 0.1uF 16VC367 C93-1959-05 C CAPACITOR 0.1uF 16VC368 C93-1959-05 C CAPACITOR 0.1uF 16VC369 CC73HCH1H220G C CAPACITOR 22pF 50V GC370 CK73HB1A105K C CAPACITOR 1uF 10V KC371 C93-1959-05 C CAPACITOR 0.1uF 16VC372 C93-1959-05 C CAPACITOR 0.1uF 16VC373 C93-1959-05 C CAPACITOR 0.1uF 16VC374 C93-1959-05 C CAPACITOR 0.1uF 16VC375 C93-1959-05 C CAPACITOR 0.1uF 16VC376 CK73HBB1H102K C CAPACITOR 1000pF 50V KC377 CK73HBB1H102K C CAPACITOR 1000pF 50V KC378 CK73HBB1H102K C CAPACITOR 1000pF 50V KC379 CK73HBB1H102K C CAPACITOR 1000pF 50V KC380 C93-1959-05 C CAPACITOR 0.1uF 16VC381 C93-1959-05 C CAPACITOR 0.1uF 16VC382 CC73HCH1H470J C CAPACITOR 47pF 50V JC383 C93-1959-05 C CAPACITOR 0.1uF 16VC384 C93-1959-05 C CAPACITOR 0.1uF 16VC385 CK73HBB1H102K C CAPACITOR 1000pF 50V KC386 C93-1959-05 C CAPACITOR 0.1uF 16VC387 C93-1959-05 C CAPACITOR 0.1uF 16VC388 CK73HB1A105K C CAPACITOR 1uF 10V KC389 CC73HCH1H100B C CAPACITOR 10pF 50V BC391 CC73HCH1H121J C CAPACITOR 120pF 50V JC392 CK73HBB1H102K C CAPACITOR 1000pF 50V KC395 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC401 CK73HB1H103K C CAPACITOR 10000pF 50V KC402 CC73JCH1H101J C CAPACITOR 100pF 50V JC403 C93-1953-05 C CAPACITOR 0.01uF 25VC404 CK73HB1H103K C CAPACITOR 10000pF 50V KC405 CC73JCH1H101J C CAPACITOR 100pF 50V JC406 CK73HB1H103K C CAPACITOR 10000pF 50V KC407 C93-1953-05 C CAPACITOR 0.01uF 25VC408 CC73HCH1H050B C CAPACITOR 5pF 50V BC421 C93-1959-05 C CAPACITOR 0.1uF 16VC422 CC73HCH1H180G C CAPACITOR 18pF 50V GC423 CC73HCH1H150G C CAPACITOR 15pF 50V GC424 CK73HB1A224K C CAPACITOR 0.22uF 10V KC425 C93-1959-05 C CAPACITOR 0.1uF 16VC426 C93-1959-05 C CAPACITOR 0.1uF 16VC427 C93-1959-05 C CAPACITOR 0.1uF 16VC428 C93-1959-05 C CAPACITOR 0.1uF 16VC429 CK73FB1C106K C CAPACITOR 10uF 16V KC430 CK73FB1C106K C CAPACITOR 10uF 16V KC431 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC432 CK73FB1C106K C CAPACITOR 10uF 16V KC433 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC434 C93-1959-05 C CAPACITOR 0.1uF 16VC435 C93-1959-05 C CAPACITOR 0.1uF 16VC436 CK73FB1C106K C CAPACITOR 10uF 16V KC437 C93-1959-05 C CAPACITOR 0.1uF 16VC438 C93-1959-05 C CAPACITOR 0.1uF 16VC439 C93-1959-05 C CAPACITOR 0.1uF 16VC440 C93-1959-05 C CAPACITOR 0.1uF 16VC441 C93-1959-05 C CAPACITOR 0.1uF 16VC442 C93-1959-05 C CAPACITOR 0.1uF 16VC443 C93-1959-05 C CAPACITOR 0.1uF 16VC444 C93-1959-05 C CAPACITOR 0.1uF 16VC445 CK73HB1A105K C CAPACITOR 1uF 10V KC446 C93-1959-05 C CAPACITOR 0.1uF 16VC447 CC73JCH1H101J C CAPACITOR 100pF 50V JC448 CK73HB1H103K C CAPACITOR 10000pF 50V KC449 C93-1953-05 C CAPACITOR 0.01uF 25VC450 C93-1959-05 C CAPACITOR 0.1uF 16VC451 C93-1959-05 C CAPACITOR 0.1uF 16VC452 CK73HB1A105K C CAPACITOR 1uF 10V KC453 CK73HB1H103K C CAPACITOR 10000pF 50V KC454 CK73HB1E104K C CAPACITOR 0.10uF 25V KC455 CC73JCH1H101J C CAPACITOR 100pF 50V J
Symbol No. Part No. Part Name Description Local
C456 C93-1967-05 C CAPACITOR 470pF 50VC457 CC73JCH1H101J C CAPACITOR 100pF 50V JC458 CC73JCH1H101J C CAPACITOR 100pF 50V JC459 CC73JCH1H101J C CAPACITOR 100pF 50V JC469 C93-1967-05 C CAPACITOR 470pF 50VC470 C93-1967-05 C CAPACITOR 470pF 50VC471 C93-1967-05 C CAPACITOR 470pF 50VC472 C93-1967-05 C CAPACITOR 470pF 50VC473 C93-1967-05 C CAPACITOR 470pF 50VC474 C93-1967-05 C CAPACITOR 470pF 50VC475 C93-1967-05 C CAPACITOR 470pF 50VC476 C93-1967-05 C CAPACITOR 470pF 50VC477 C93-1967-05 C CAPACITOR 470pF 50VC480 CC73JCH1H101J C CAPACITOR 100pF 50V JC481 CC73JCH1H101J C CAPACITOR 100pF 50V JC482 CC73JCH1H101J C CAPACITOR 100pF 50V JC483 CC73JCH1H101J C CAPACITOR 100pF 50V JC484 CC73JCH1H101J C CAPACITOR 100pF 50V JC485 CC73JCH1H101J C CAPACITOR 100pF 50V JC486 CC73JCH1H101J C CAPACITOR 100pF 50V JC487 CC73JCH1H101J C CAPACITOR 100pF 50V JC488 CC73JCH1H101J C CAPACITOR 100pF 50V JC489 CC73JCH1H101J C CAPACITOR 100pF 50V JC496 CK73HB1A105K C CAPACITOR 1uF 10V KC497 C93-1959-05 C CAPACITOR 0.1uF 16VC498 C93-1959-05 C CAPACITOR 0.1uF 16VC499 C93-1959-05 C CAPACITOR 0.1uF 16VC500 C93-1959-05 C CAPACITOR 0.1uF 16VC501 CK73HB1A105K C CAPACITOR 1uF 10V KC502 C93-1959-05 C CAPACITOR 0.1uF 16VC510 C93-1967-05 C CAPACITOR 470pF 50VC515 C93-1967-05 C CAPACITOR 470pF 50VC516 CK73HB1E104K C CAPACITOR 0.10uF 25V KC517 CK73HB1E104K C CAPACITOR 0.10uF 25V KC518 CK73HB1E104K C CAPACITOR 0.10uF 25V KC601 CK73HB1E104K C CAPACITOR 0.10uF 25V KC602 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC603 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC604 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC606 CK73HB1A105K C CAPACITOR 1uF 10V KC607 CK73HB1A105K C CAPACITOR 1uF 10V KC608 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC609 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC610 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC612 CK73HB1A105K C CAPACITOR 1uF 10V KC615 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC617 CC73JCH1H101J C CAPACITOR 100pF 50V JC618 CC73JCH1H101J C CAPACITOR 100pF 50V JC620 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC621 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC622 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC625 CK73HB1A334K C CAPACITOR 0.33uF 10V KC626 CK73HB1H103K C CAPACITOR 10000pF 50V KC627 CK73HB1A334K C CAPACITOR 0.33uF 10V KC657 CC73HCH1H101J C CAPACITOR 100pF 50V JC658 CC73HCH1H101J C CAPACITOR 100pF 50V JC659 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC663 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC664 CK73EXR0J476M C CAPACITOR 47uF 6.3V MC667 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC669 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC671 CK73HBB1C683K C CAPACITOR 0.068uF 16V KC672 CK73GB1E104K C CAPACITOR 0.1uF 25V KC673 CK73HB1E104K C CAPACITOR 0.10uF 25V KC674 CK73GB1E105K C CAPACITOR 1uF 25V KC675 CK73EXR0J476M C CAPACITOR 47uF 6.3V MC676 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC677 CC73HCH1H221J C CAPACITOR 220pF 50V JC679 CC73HCH1H221J C CAPACITOR 220pF 50V JC681 CC73HCH1H101J C CAPACITOR 100pF 50V JC683 CK73HB1E104K C CAPACITOR 0.10uF 25V KC684 CC73HCH1H221J C CAPACITOR 220pF 50V JC686 CK73GB1E105K C CAPACITOR 1uF 25V KC687 CK73HB1E104K C CAPACITOR 0.10uF 25V KC688 CK73HB1A105K C CAPACITOR 1uF 10V KC689 CC73HCH1H470J C CAPACITOR 47pF 50V JC690 CC73HCH1H221J C CAPACITOR 220pF 50V JC691 CK73GXR1C225K C CAPACITOR 2.2uF 16V K
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-7
C692 CK73GB1E104K C CAPACITOR 0.1uF 25V KC693 C93-1967-05 C CAPACITOR 470pF 50VC695 C93-1967-05 C CAPACITOR 470pF 50VC697 C93-1953-05 C CAPACITOR 0.01uF 25VC698 C93-1953-05 C CAPACITOR 0.01uF 25V
R1 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR7 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR8 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR9 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR10 RK73HH1J184D MG RESISTOR 180kΩ 1/16W DR11 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR12 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR13 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR14 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR15 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR16 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR17 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR18 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR19 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR20 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR21 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR22 RK73HH1J183D MG RESISTOR 18kΩ 1/16W DR23 RK73HH1J683D MG RESISTOR 68kΩ 1/16W DR24 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR25 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR26 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR27 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR28 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR29 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR30 RK73HH1J274D MG RESISTOR 270kΩ 1/16W DR31 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR32 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR33 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR34 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR35 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR36 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR37 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR38 RZ73G0BK2R7J RESISTOR 2.7Ω 0.25W JR39 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR40 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR41 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR42 R92-3774-05 MG RESISTOR 27Ω 0.25WR43 R92-3774-05 MG RESISTOR 27Ω 0.25WR44 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR45 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR46 RK73GB2A220J MG RESISTOR 22Ω 1/10W JR47 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR48 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR49 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR50 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR51 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR52 RK73FB2B1R0J MG RESISTOR 1Ω 1/8W JR56 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR57 RK73HH1J183D MG RESISTOR 18kΩ 1/16W DR58 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR59 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR60 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR65 RK73HH1J474D MG RESISTOR 470kΩ 1/16W DR66 RK73HH1J474D MG RESISTOR 470kΩ 1/16W DR102 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR103 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR104 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR105 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR106 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR107 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR108 RK73HB1J106J MG RESISTOR 10MΩ 1/16W JR109 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR110 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR111 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR112 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR113 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR116 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR120 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR121 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR122 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR123 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR124 RK73HB1J473J MG RESISTOR 47kΩ 1/16W J
Symbol No. Part No. Part Name Description Local
R125 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR126 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR127 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR128 RK73HH1J391D MG RESISTOR 390Ω 1/16W DR129 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR130 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR131 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR132 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR133 RN73HH1J151D MG RESISTOR 150Ω 0.063W DR134 RN73HH1J100D MF RESISTOR 10Ω 0.063W DR135 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR136 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR137 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR139 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR140 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR141 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR142 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR143 RK73HB1J562J MG RESISTOR 5.6kΩ 1/16W JR145 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR181 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR182 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR183 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR184 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR192 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR193 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR194 RK73HB1J330J MG RESISTOR 33Ω 1/16W JR195 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR201 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR202 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR204 R92-3785-05 MG RESISTOR 120Ω 0.25WR205 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR206 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR207 RK73HB1J180J MG RESISTOR 18Ω 1/16W JR208 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR209 RK73HB1J562J MG RESISTOR 5.6kΩ 1/16W JR210 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR211 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR212 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR213 RK73HB1J121J MG RESISTOR 120Ω 1/16W JR214 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR215 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR216 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR218 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR219 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR220 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR222 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR223 RK73HB1J330J MG RESISTOR 33Ω 1/16W JR227 RK73GB2A823J MG RESISTOR 82kΩ 1/10W JR228 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR230 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR233 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR234 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR237 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR244 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR245 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR246 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR247 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR248 R92-3756-05 MG RESISTOR 0.22Ω 1/3WR249 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR250 R92-3756-05 MG RESISTOR 0.22Ω 1/3WR251 RK73HB1J270J MG RESISTOR 27Ω 1/16W JR252 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR253 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR255 RK73HH1J393D MG RESISTOR 39kΩ 1/16W DR256 RK73HH1J682D MG RESISTOR 6.8kΩ 1/16W DR257 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR258 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR259 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR260 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR264 RK73HH1J682D MG RESISTOR 6.8kΩ 1/16W DR265 RK73HH1J393D MG RESISTOR 39kΩ 1/16W DR267 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR268 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR269 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR270 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR271 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR272 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR273 RK73HB1J000J MG RESISTOR 0Ω 1/16W J
Symbol No. Part No. Part Name Description Local
3-8(No.RA053<Rev.001>)
R301 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR302 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR303 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR304 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR310 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR312 RK73HB1J5R6J MG RESISTOR 5.6Ω 1/16W JR313 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR314 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR315 RK73HB1J180J MG RESISTOR 18Ω 1/16W JR316 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR325 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR330 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR331 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR332 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR333 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR335 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR336 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR351 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR352 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR353 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR354 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR355 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR356 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR357 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR358 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR359 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR360 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR361 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR362 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR363 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR364 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR365 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR366 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR367 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR369 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR401 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR402 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR403 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR404 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR405 RK73HB1J153J MG RESISTOR 15kΩ 1/16W JR406 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR407 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR408 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR410 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR411 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR412 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR413 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR414 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR415 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR419 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR420 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR421 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR422 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR423 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR424 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR425 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR426 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR427 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR428 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR429 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR430 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR431 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR432 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR433 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR434 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR435 RK73JB1H105J MG RESISTOR 1MΩ 1/20W JR436 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR437 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR438 RK73GH2A49R9D MG RESISTOR 49.9Ω 1/10W DR439 RK73HH1J102D MG RESISTOR 1kΩ 1/16W DR440 RK73HH1J102D MG RESISTOR 1kΩ 1/16W DR441 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR442 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR443 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR444 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR445 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR446 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR447 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W J
Symbol No. Part No. Part Name Description Local
R448 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR449 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR450 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR451 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR452 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR461 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR462 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR463 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR464 RK73HH1J103D MG RESISTOR 10kΩ 1/16W DR466 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR467 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR468 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR469 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR470 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR479 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR480 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR601 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR602 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR604 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR605 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR608 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR609 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR610 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR617 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR635 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR636 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR637 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR638 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR639 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR650 RK73HB1J683J MG RESISTOR 68kΩ 1/16W JR651 RK73HB1J152J MG RESISTOR 1.5kΩ 1/16W JR652 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR653 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR654 RK73GB2A471J MG RESISTOR 470Ω 1/10W JR655 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR656 RK73PB2H1R2J MG RESISTOR 1.2Ω 1/2W JR657 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR658 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR659 RK73HB1J561J MG RESISTOR 560Ω 1/16W JR661 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR663 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR664 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR665 RK73HB1J334J MG RESISTOR 330kΩ 1/16W JR667 RK73JB1H224J MG RESISTOR 220kΩ 1/20W JR668 RK73JB1H681J MG RESISTOR 680Ω 1/20W JR670 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR672 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR676 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR678 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR680 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR681 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR682 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR683 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR684 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR685 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J
L1 LB73F0AW-002 CHIP FERRITEL3 LB73G0AM-004 CHIP FERRITEL4 LR73Z0AY2R2M CHIP INDUCTORL5 LB73G0AM-004 CHIP FERRITEL6 LB73G0AM-004 CHIP FERRITEL7 LB73G0AM-004 CHIP FERRITEL8 LB73G0AM-004 CHIP FERRITEL9 LB73H0AV-002 CHIP FERRITEL10 LB73H0AV-002 CHIP FERRITEL11 LB73H0AV-002 CHIP FERRITEL12 L41-1502-70 CHIP INDUCTORL13 LB73H0AV-002 CHIP FERRITEL112 LB73H0AY-004 CHIP FERRITEL121 LB73H0AY-004 CHIP FERRITEL131 L41-2785-53 CHIP INDUCTORL132 L41-2785-53 CHIP INDUCTORL135 L41-2785-53 CHIP INDUCTORL136 LB73H0AY-004 CHIP FERRITEL137 L41-2785-53 CHIP INDUCTORL138 L41-3378-08 CHIP INDUCTORL139 L41-2785-53 CHIP INDUCTORL140 L41-2785-53 CHIP INDUCTOR
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-9
TX-RX UNITXC1-180K-00 (NX-3320(K),NX-3320(K2),NX-3320(K3),NX-3320(E),NX-3320(E2),NX-3320(E3))
*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][2]
L141 LB73H0AY-004 CHIP FERRITEL142 L41-2785-53 CHIP INDUCTORL143 LK73H0AM47NJ M.CHIP INDUCTOR 47nHL181 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL191 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL192 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL201 LR79Z0DC45N5J CHIP INDUCTOR 45.5nHL203 LR73Z0AE2R2J CHIP INDUCTOR 2.2uHL206 LK73H0AMR27J M.CHIP INDUCTORL209 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL210 LR79Z0DC22NJ CHIP INDUCTOR 22nHL211 LB73F0AW-002 CHIP FERRITEL213 LR79Z0DC27N9J CHIP INDUCTOR 27.9nHL214 LB73F0AW-002 CHIP FERRITEL215 LR79Z0DD43N6J CHIP INDUCTOR 43.6nHL216 LR79Z0DD43N6J CHIP INDUCTOR 43.6nHL217 LR79Z0DD43N6J CHIP INDUCTOR 43.6nHL218 LR79Z0CA68NJ CHIP INDUCTORL219 LR79Z0DC16N7J CHIP INDUCTOR 16.7nHL220 LR79Z0DD12N2J CHIP INDUCTOR 12.2nHL221 LK73H0AM56NJ M.CHIP INDUCTOR 56nHL222 L41-8265-53 CHIP INDUCTORL223 L41-6865-53 CHIP INDUCTORL301 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL302 LR79G0CQ47NG CHIP INDUCTORL303 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL304 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL305 LR79G0CQR18G CHIP INDUCTORL307 LR79G0CQ56NG CHIP INDUCTORL308 LR79G0CQ47NG CHIP INDUCTORL309 LR79G0CQ82NG CHIP INDUCTORL310 LR79G0CQ8N2C CHIP INDUCTORL311 LR79G0CQR22G CHIP INDUCTORL312 LR79G0CQR15G CHIP INDUCTORL313 LR79G0CQ82NG CHIP INDUCTORL314 LR79G0CQ82NG CHIP INDUCTORL315 LR79G0CQR33G CHIP INDUCTORL351 L92-0487-05 CHIP FERRITEL352 L92-0487-05 CHIP FERRITEL353 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL354 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL358 L92-0487-05 CHIP FERRITEL359 L7K-0059-00 FILTERL361 L79-1987-05 FILTERL365 L92-0487-05 CHIP FERRITEL366 L92-0487-05 CHIP FERRITEL401 LB73H0AV-002 CHIP FERRITEL402 LK73G0AQ4R7K M.CHIP INDUCTOR 4.7uHL404 LB73G0AM-004 CHIP FERRITEL405 L92-1101-05 CHIP FERRITEL406 L92-1101-05 CHIP FERRITEL407 LB73G0AM-004 CHIP FERRITEL408 LB73G0AM-004 CHIP FERRITEL409 LB73G0AM-004 CHIP FERRITEL410 LB73G0AM-004 CHIP FERRITEL411 L79-1946-05 FILTERL412 L79-1946-05 FILTERL413 L79-1946-05 FILTERL414 L79-1946-05 FILTERL415 L79-1946-05 FILTERL416 L79-1946-05 FILTERL417 LB73H0AV-002 CHIP FERRITEL427 LB73H0AV-002 CHIP FERRITEL428 LB73H0AV-002 CHIP FERRITEL429 LB73H0AV-002 CHIP FERRITEL430 LB73H0AV-002 CHIP FERRITEL431 LB73H0AV-002 CHIP FERRITEL601 LB73G0AM-004 CHIP FERRITEL604 LB73G0AM-004 CHIP FERRITEL605 LB73G0AM-004 CHIP FERRITEL608 LR73Z0AY100M CHIP INDUCTORL609 LR73Z0AY100M CHIP INDUCTORL610 LB73G0AM-004 CHIP FERRITEL612 LB73G0AM-004 CHIP FERRITEL613 LB73G0AM-004 CHIP FERRITEL622 LB73G0AM-004 CHIP FERRITEL623 LB73G0AM-004 CHIP FERRITEL635 LB73H0AV-002 CHIP FERRITE
Symbol No. Part No. Part Name Description Local
CN1 EC720CQ-0313A FFC FPC CONNECTORCN2 J19-5386-05 HOLDERCN7 E40-6883-05 F.C.CONNECTORCN8 ------------ TERMINAL *NoteCN10 ------------ TERMINAL *NoteCN201 E2D-0058-00 TERMINALCN202 E2D-0058-00 TERMINALCN203 E2D-0022-00 TERMINALCN353 G0B-0005-00 EARTH SPRINGCN354 G0B-0005-00 EARTH SPRINGCN356 G0B-0005-00 EARTH SPRINGCN357 G0B-0005-00 EARTH SPRINGCN402 EC720BP-0341A FFC FPC CONNECTORCN602 E41-1476-05 PIN ASSYCP1 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP2 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP301 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP302 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP303 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP351 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP352 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP401 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP402 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP403 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP404 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP405 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP406 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP408 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP409 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP410 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP411 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP412 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP413 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP414 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP601 RK74HB1J100J NET RESISTOR 10Ω 1/16W JE101 ------------ SHIELDING CASE *NoteE301 ------------ SHIELDING CASE *NoteE351 F10-3228-15 SHIELDING CASEE401 ------------ SHIELDING CASE *NoteE601 ------------ SHIELDING CASE *NoteF1 FZA10BQ-3R15 FUSE (CC)F2 FZA10BH-R50 FUSE (CC) 0.5AF650 FZA10BH-R315 FUSE (CC) 0.315AJ651 E1B-0019-00 3.5D PHONE JACKJ652 E1B-0020-00 2.5D PHONE JACKTH201 NCU15WF104F6S N THERMISTORTH401 NCU15WF104F6S N THERMISTORX351 L77-3121-05 QUARTZ CRYSTALX401 L7H-0076-00 TCXOX402 L77-1802-05 QUARTZ CRYSTAL
Symbol No. Part No. Part Name Description Local
IC1 XC61CC5602N-G ICIC2 LXDC2XQ12A-252 ICIC3 TPS62140RGT ICIC4 LXDC2HN18F163 ICIC5 ------------ IC *NoteIC6 XC6209B502D-G ICIC7 ------------ IC *NoteIC8 BU18TD2WNVX ICIC9 XC6209B312D-G ICIC10 XC6215B122N-G ICIC11 NJM2878F4-32 IC
Symbol No. Part No. Part Name Description Local
3-10(No.RA053<Rev.001>)
IC12 XC8102AA07-G ICIC13 TPS61041DRVR ICIC14 ------------ IC *NoteIC15 XC6209B502D-G ICIC17 XC6209B502D-G ICIC18 BU7442NUX ICIC101 OPA170AIDRLR ICIC102 BU7295HFV ICIC201 XC8102AA07-G ICIC202 BGU6104 ICIC203 BA3472FVM ICIC303 ------------ IC *NoteIC351 ------------ IC *NoteIC352 74AVC4TD245GU ICIC353 74AVC4TD245GU ICIC401 ------------ IC *NoteIC402 ------------ IC *NoteIC403 S-80135ANPF-G ICIC404 ------------ IC *NoteIC405 TC7SZ08FE ICIC406 KXCJ9-1008 ICIC409 ADS7961SRHB ICIC410 DAC124S085CIS ICIC601 ------------ IC *NoteIC650 TA7368FG ICIC651 XC6209B502D-G ICIC652 TC7SET125FUF ICIC654 TC7SZ08FE IC
Q1 EMD12 DIGI TRANSISTORQ2 SSM6N15AFEM DUAL FETQ3 SSM6N15AFEM DUAL FETQ4 VT6M1 FETQ5 VT6M1 FETQ6 LTC014EEBFS8 DIGI TRANSISTORQ7 2SB1132(Q,R) TRANSISTORQ102 EM6M2 FETQ103 VT6M1 FETQ111 RE1E002SP FETQ112 VT6M1 FETQ113 2SD2654/W/ TRANSISTORQ114 VT6M1 FETQ116 SSM3K15AMFV FETQ131 BFU660F TRANSISTORQ151 BFU660F TRANSISTORQ181 2SC5108FT/Y/ TRANSISTORQ201 RD01MUS2BT513 FETQ202 RD08MUS2T514 FETQ203 LSCR523EBFS8 TRANSISTORQ204 LTC044EEBFS8 DIGI TRANSISTORQ205 SSM3K15AMFV FETQ206 SSM3K15AMFV FETQ207 EMD12 DIGI TRANSISTORQ351 SSM3K15AMFV FETQ401 2SC4617/S/ TRANSISTORQ402 LTC044EEBFS8 DIGI TRANSISTORQ650 2SB1694 TRANSISTORQ651 SSM3K324RF FETQ652 SSM3K324RF FETQ653 LTC014EEBFS8 DIGI TRANSISTORQ654 LTC044EEBFS8 DIGI TRANSISTORQ656 RE1C001UN DIGI TRANSISTOR
D1 RR1LAM4S DIODED8 DAN222 DIODE ARRAYD9 RB520SM-30 DIODED10 RB561VM-40 SCHOTTKY DIODED102 EDZV8.2B ZENER DIODED111 1SS400SM DIODED131 BBY58-02V VARI CAP DIODED132 BB555-02VH VARI CAP DIODED133 BB555-02VH VARI CAP DIODED134 BB555-02VH VARI CAP DIODED135 BB555-02VH VARI CAP DIODED151 BBY58-02V VARI CAP DIODED152 SMV1130-079LF VARI CAP DIODED153 SMV1130-079LF VARI CAP DIODED154 BB555-02VH VARI CAP DIODE
Symbol No. Part No. Part Name Description Local
D155 BB664-02V VARI CAP DIODED201 L5208F DIODED202 RN142S DIODED203 RN142S DIODED204 EDZV5.6B ZENER DIODED206 SPC10501A01 VARISTORD301 1SS400SM DIODED302 1SS400SM DIODED303 1SS390 DIODED304 1SS390 DIODED401 RB521CM-30 DIODED402 RB521CM-30 DIODED403 1SS400SM DIODED404 1SS400SM DIODED405 1SS400SM DIODED406 1SS400SM DIODED407 1SS400SM DIODED609 RB521CM-30 DIODED620 EDZV6.8B ZENER DIODED621 EDZV6.8B ZENER DIODED650 RB706F-40-MC DIODED651 EDZV6.8B ZENER DIODED652 EDZV6.8B ZENER DIODED653 SPC10501A01 VARISTORD654 SPC10501A01 VARISTORD655 AVRM10120MAAB VARISTOR
C1 CK73HBB1H102K C CAPACITOR 1000pF 50V KC2 CC73HCH1H220G C CAPACITOR 22pF 50V GC3 CK73HBB1H682K C CAPACITOR 6800pF 50V KC4 C93-1967-05 C CAPACITOR 470pF 50VC5 C93-1967-05 C CAPACITOR 470pF 50VC6 C93-1967-05 C CAPACITOR 470pF 50VC7 C93-1967-05 C CAPACITOR 470pF 50VC8 C93-1967-05 C CAPACITOR 470pF 50VC9 CK73HBB1H682K C CAPACITOR 6800pF 50V KC10 C93-1967-05 C CAPACITOR 470pF 50VC14 C93-1967-05 C CAPACITOR 470pF 50VC15 CK73HB1A224K C CAPACITOR 0.22uF 10V KC16 CK73HB1A224K C CAPACITOR 0.22uF 10V KC17 CK73HBB1H471K C CAPACITOR 470pF 50V KC18 CK73FB1C106K C CAPACITOR 10uF 16V KC19 CK73FB1C106K C CAPACITOR 10uF 16V KC20 CK73HBB1H332K C CAPACITOR 3300pF 50V KC21 CK73HB1E104K C CAPACITOR 0.10uF 25V KC22 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC23 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC24 CK73GB0J106K C CAPACITOR 10uF 6.3V KC25 CK73HB1A474K C CAPACITOR 0.47uF 10V KC26 CK73HB1A474K C CAPACITOR 0.47uF 10V KC27 CK73GB1E104K C CAPACITOR 0.1uF 25V KC28 C93-1967-05 C CAPACITOR 470pF 50VC29 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC30 CK73HBB1H471K C CAPACITOR 470pF 50V KC31 CK73FB1C106K C CAPACITOR 10uF 16V KC32 CK73GB0J106K C CAPACITOR 10uF 6.3V KC33 CK73HB1A224K C CAPACITOR 0.22uF 10V KC34 CK73HB1A224K C CAPACITOR 0.22uF 10V KC35 CK73HB1E104K C CAPACITOR 0.10uF 25V KC36 C93-1967-05 C CAPACITOR 470pF 50VC37 C93-1967-05 C CAPACITOR 470pF 50VC38 CK73GB1E104K C CAPACITOR 0.1uF 25V KC39 CK73GB1E105K C CAPACITOR 1uF 25V KC40 CK73HB1E104K C CAPACITOR 0.10uF 25V KC41 CK73HB1E104K C CAPACITOR 0.10uF 25V KC42 CK73HB1E104K C CAPACITOR 0.10uF 25V KC43 CK73HB1A474K C CAPACITOR 0.47uF 10V KC44 CK73HB1E104K C CAPACITOR 0.10uF 25V KC46 CK73GB1A335K C CAPACITOR 3.3uF 10V KC47 CK73GB1A335K C CAPACITOR 3.3uF 10V KC48 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC49 CK73HBB1H681K C CAPACITOR 680pF 50V KC50 CK730JM1H684K C CAPACITOR 0.68uF 50V KC51 CK73HB1A224K C CAPACITOR 0.22uF 10V KC52 CK73HBB1H681K C CAPACITOR 680pF 50V KC54 CK73GB1E104K C CAPACITOR 0.1uF 25V KC55 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC56 CK73HBB1H471K C CAPACITOR 470pF 50V K
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-11
C60 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC62 C93-1959-05 C CAPACITOR 0.1uF 16VC63 C93-1959-05 C CAPACITOR 0.1uF 16VC64 C93-1959-05 C CAPACITOR 0.1uF 16VC65 CK73HBB1H102K C CAPACITOR 1000pF 50V KC66 CK73HBB1H471K C CAPACITOR 470pF 50V KC67 CC73JCH1H101J C CAPACITOR 100pF 50V JC68 CC73JCH1H101J C CAPACITOR 100pF 50V JC69 CC73JCH1H101J C CAPACITOR 100pF 50V JC70 CC73JCH1H101J C CAPACITOR 100pF 50V JC102 CK73HB1H103K C CAPACITOR 10000pF 50V KC103 CC73HCH1H330G C CAPACITOR 33pF 50V GC104 CC73JCH1H101J C CAPACITOR 100pF 50V JC105 CK73GB1H105K C CAPACITOR 1uF 50V KC106 C93-1959-05 C CAPACITOR 0.1uF 16VC107 CC73JCH1H101J C CAPACITOR 100pF 50V JC108 CC730AD1H104J C CAPACITOR 0.1uF 50V JC109 CC73HCH1H130G C CAPACITOR 13pF 50V GC110 CC73HCH1H050B C CAPACITOR 5pF 50V BC111 CC73HCH1H470G C CAPACITOR 47pF 50V GC112 CS77BP1A4R7M TA E CAPACITOR 4.7uF 10V MC113 CK73HB1A105K C CAPACITOR 1uF 10V KC115 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC116 CC73HCH1H030B C CAPACITOR 3pF 50V BC117 CC73HCH1HR75B C CAPACITOR 0.75pF 50V BC121 CK73FBB1H154K C CAPACITOR 0.15uF 50V KC122 CS77ABE1D100M TA E CAPACITOR 10uF 20V MC123 CK73FB1H473K C CAPACITOR 0.047uF 50V KC131 CC73HCH1H010B C CAPACITOR 1pF 50V BC132 CC73HCH1H470G C CAPACITOR 47pF 50V GC133 CC73HCH1H130G C CAPACITOR 13pF 50V GC134 CC73HCH1H020B C CAPACITOR 2pF 50V BC135 CC73HCH1H470G C CAPACITOR 47pF 50V GC136 CC73HCH1H030B C CAPACITOR 3pF 50V BC138 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC139 CC73HCH1H470G C CAPACITOR 47pF 50V GC140 CK73HB1A334K C CAPACITOR 0.33uF 10V KC141 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC142 CC73HCH1H040B C CAPACITOR 4pF 50V BC143 CC73HCH1H040B C CAPACITOR 4pF 50V BC144 CC73HCH1H470G C CAPACITOR 47pF 50V GC145 CC73HCH1H010B C CAPACITOR 1pF 50V BC148 CK73HB1E104K C CAPACITOR 0.10uF 25V KC150 CC73HCH1H470G C CAPACITOR 47pF 50V GC151 CC73HCH1H040B C CAPACITOR 4pF 50V BC152 CC73HCH1H470G C CAPACITOR 47pF 50V GC153 CC73HCH1H130G C CAPACITOR 13pF 50V GC154 CC73HCH1H470G C CAPACITOR 47pF 50V GC156 CC73HCH1H040B C CAPACITOR 4pF 50V BC157 CC73HCH1H030B C CAPACITOR 3pF 50V BC158 CC73HCH1H0R5B C CAPACITOR 0.5pF 50V BC159 CC73HCH1H470G C CAPACITOR 47pF 50V GC160 CK73HB1A334K C CAPACITOR 0.33uF 10V KC161 CC73HCH1H090B C CAPACITOR 9pF 50V BC162 CC73HCH1H070B C CAPACITOR 7pF 50V BC163 CC73HCH1H3R5B C CAPACITOR 3.5pF 50V BC164 CC73HCH1H470G C CAPACITOR 47pF 50V GC165 CK73HB1E104K C CAPACITOR 0.10uF 25V KC166 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC167 CC73HCH1H470G C CAPACITOR 47pF 50V GC181 CC73HCH1H470G C CAPACITOR 47pF 50V GC182 CC73HCH1H470G C CAPACITOR 47pF 50V GC183 CC73HCH1H030B C CAPACITOR 3pF 50V BC191 CC73HCH1H020B C CAPACITOR 2pF 50V BC192 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC193 CC73HCH1H020B C CAPACITOR 2pF 50V BC194 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC195 CK73HBB1H102K C CAPACITOR 1000pF 50V KC197 CC73HCH1H101J C CAPACITOR 100pF 50V JC198 CC73HCH1H020B C CAPACITOR 2pF 50V BC203 C93-0871-05 C CAPACITOR 1.0pF 100VC208 CC73GCH1H030B C CAPACITOR 3pF 50V BC209 CC73HCH1H050B C CAPACITOR 5pF 50V BC211 CK73HBB1H471K C CAPACITOR 470pF 50V KC212 CK73HBB1H471K C CAPACITOR 470pF 50V KC213 CK73HBB1H471K C CAPACITOR 470pF 50V KC214 CK73HBB1H471K C CAPACITOR 470pF 50V KC215 CK73HBB1H471K C CAPACITOR 470pF 50V K
Symbol No. Part No. Part Name Description Local
C216 CC73HCH1H100B C CAPACITOR 10pF 50V BC217 CC73HCH1H100B C CAPACITOR 10pF 50V BC218 CK73HBB1H471K C CAPACITOR 470pF 50V KC219 CC73HCH1H100B C CAPACITOR 10pF 50V BC220 CK73HBB1H471K C CAPACITOR 470pF 50V KC221 CK73HB1E473K C CAPACITOR 0.047uF 25V KC222 CK73HBB1H472K C CAPACITOR 4700pF 50V KC223 CC73HCH1H101J C CAPACITOR 100pF 50V JC224 CK73HBB1H471K C CAPACITOR 470pF 50V KC225 CK73HBB1H471K C CAPACITOR 470pF 50V KC226 C93-0947-05 C CAPACITOR 33pF 50VC227 CC73GCH1H101J C CAPACITOR 100pF 50V JC228 CC73GCH1H010B C CAPACITOR 1pF 50V BC229 CC73HCH1H050B C CAPACITOR 5pF 50V BC230 CC73HCH1H150G C CAPACITOR 15pF 50V GC231 CC73HCH1H150G C CAPACITOR 15pF 50V GC232 CK73HBB1H471K C CAPACITOR 470pF 50V KC233 CK73HBB1H471K C CAPACITOR 470pF 50V KC234 CK73HBB1H471K C CAPACITOR 470pF 50V KC235 CK73HBB1H471K C CAPACITOR 470pF 50V KC236 C93-0979-05 C CAPACITOR 4.7pF 50VC237 CK73HBB1H471K C CAPACITOR 470pF 50V KC239 CK73HBB1H471K C CAPACITOR 470pF 50V KC240 CC73HCH1H151J C CAPACITOR 150pF 50V JC241 CK73HBB1H471K C CAPACITOR 470pF 50V KC243 CK73HB1E104K C CAPACITOR 0.10uF 25V KC244 C93-0941-05 C CAPACITOR 18pF 50VC245 C93-0941-05 C CAPACITOR 18pF 50VC246 CC73GCH1H101J C CAPACITOR 100pF 50V JC247 CC73GCH1H070B C CAPACITOR 7pF 50V BC248 CC73GCH1H1R5B C CAPACITOR 1.5pF 50V BC249 CC73GCH1H070B C CAPACITOR 7pF 50V BC250 CC73GCH1H010B C CAPACITOR 1pF 50V BC251 CC73GCH1H040B C CAPACITOR 4pF 50V BC252 CC73HCH1H180G C CAPACITOR 18pF 50V GC253 CC73HCH1H220G C CAPACITOR 22pF 50V GC255 C93-0935-05 C CAPACITOR 10pF 50VC257 CK73HBB1H471K C CAPACITOR 470pF 50V KC258 C93-1967-05 C CAPACITOR 470pF 50VC259 C93-1967-05 C CAPACITOR 470pF 50VC261 CK73HBB1H471K C CAPACITOR 470pF 50V KC262 CK73GB1C563K C CAPACITOR 0.056uF 16V KC263 CK73HBB1H471K C CAPACITOR 470pF 50V KC264 CK73HB1H822K C CAPACITOR 8200pF 50V KC265 CK73HB1H822K C CAPACITOR 8200pF 50V KC266 C93-1967-05 C CAPACITOR 470pF 50VC267 CK73HBB1H471K C CAPACITOR 470pF 50V KC268 CC73HCH1H390G C CAPACITOR 39pF 50V GC270 CC73GCH1H030B C CAPACITOR 3pF 50V BC301 CK73HB0J225K C CAPACITOR 2.2uF 6.3V KC302 CC73HCH1H030B C CAPACITOR 3pF 50V BC303 CK73HB1H103K C CAPACITOR 10000pF 50V KC304 CK73HB1A105K C CAPACITOR 1uF 10V KC305 CC73HCH1H020B C CAPACITOR 2pF 50V BC306 CK73HBB1H471K C CAPACITOR 470pF 50V KC308 CC73HCH1H100B C CAPACITOR 10pF 50V BC309 CC73HCH1H050B C CAPACITOR 5pF 50V BC310 CC73HCH1H050B C CAPACITOR 5pF 50V BC311 CC73HCH1H040B C CAPACITOR 4pF 50V BC312 CC73HCH1H040B C CAPACITOR 4pF 50V BC313 CK73HBB1H102K C CAPACITOR 1000pF 50V KC314 CK73HB1H103K C CAPACITOR 10000pF 50V KC315 CK73HB1A105K C CAPACITOR 1uF 10V KC316 CK730BS0J106M C CAPACITOR 10uF 6.3V MC317 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC319 CC73HCH1H060B C CAPACITOR 6pF 50V BC320 CC73HCH1H150G C CAPACITOR 15pF 50V GC321 CK73HB1E104K C CAPACITOR 0.10uF 25V KC322 CC73HCH1H101J C CAPACITOR 100pF 50V JC323 CC73HCH1H101J C CAPACITOR 100pF 50V JC324 CK73HB1H103K C CAPACITOR 10000pF 50V KC325 CC73HCH1H101J C CAPACITOR 100pF 50V JC326 CK73HB1H103K C CAPACITOR 10000pF 50V KC327 CK73HB1E104K C CAPACITOR 0.10uF 25V KC328 CC73HCH1H101J C CAPACITOR 100pF 50V JC329 CK73HB1E104K C CAPACITOR 0.10uF 25V KC330 CC73HCH1H101J C CAPACITOR 100pF 50V JC331 CC73HCH1H101J C CAPACITOR 100pF 50V J
Symbol No. Part No. Part Name Description Local
3-12(No.RA053<Rev.001>)
C332 CK73HB1E104K C CAPACITOR 0.10uF 25V KC333 CK730BS0J106M C CAPACITOR 10uF 6.3V MC334 CC73HCH1H080B C CAPACITOR 8pF 50V BC338 CK73HBB1H471K C CAPACITOR 470pF 50V KC341 CC73HCH1H101J C CAPACITOR 100pF 50V JC342 CK730BS0J106M C CAPACITOR 10uF 6.3V MC343 CK73HB1A474K C CAPACITOR 0.47uF 10V KC344 CK73HBB1H471K C CAPACITOR 470pF 50V KC345 CK73HB1A105K C CAPACITOR 1uF 10V KC346 CK73HBB1H102K C CAPACITOR 1000pF 50V KC354 CC73HCH1H040B C CAPACITOR 4pF 50V BC356 C93-1953-05 C CAPACITOR 0.01uF 25VC357 CK73HB1A105K C CAPACITOR 1uF 10V KC358 C93-1959-05 C CAPACITOR 0.1uF 16VC359 C93-1959-05 C CAPACITOR 0.1uF 16VC360 C93-1959-05 C CAPACITOR 0.1uF 16VC361 C93-1959-05 C CAPACITOR 0.1uF 16VC363 CC73HCH1H180G C CAPACITOR 18pF 50V GC364 CK73HB1A105K C CAPACITOR 1uF 10V KC365 CK73HB1A105K C CAPACITOR 1uF 10V KC366 C93-1959-05 C CAPACITOR 0.1uF 16VC367 C93-1959-05 C CAPACITOR 0.1uF 16VC368 C93-1959-05 C CAPACITOR 0.1uF 16VC369 CC73HCH1H220G C CAPACITOR 22pF 50V GC370 CK73HB1A105K C CAPACITOR 1uF 10V KC371 C93-1959-05 C CAPACITOR 0.1uF 16VC372 C93-1959-05 C CAPACITOR 0.1uF 16VC373 C93-1959-05 C CAPACITOR 0.1uF 16VC374 C93-1959-05 C CAPACITOR 0.1uF 16VC375 C93-1959-05 C CAPACITOR 0.1uF 16VC376 CK73HBB1H102K C CAPACITOR 1000pF 50V KC377 CK73HBB1H102K C CAPACITOR 1000pF 50V KC378 CK73HBB1H102K C CAPACITOR 1000pF 50V KC379 CK73HBB1H102K C CAPACITOR 1000pF 50V KC380 C93-1959-05 C CAPACITOR 0.1uF 16VC381 C93-1959-05 C CAPACITOR 0.1uF 16VC382 CC73HCH1H470G C CAPACITOR 47pF 50V GC383 C93-1959-05 C CAPACITOR 0.1uF 16VC384 C93-1959-05 C CAPACITOR 0.1uF 16VC385 CK73HBB1H102K C CAPACITOR 1000pF 50V KC386 C93-1959-05 C CAPACITOR 0.1uF 16VC387 C93-1959-05 C CAPACITOR 0.1uF 16VC388 CK73HB1A105K C CAPACITOR 1uF 10V KC389 CC73HCH1H100B C CAPACITOR 10pF 50V BC391 CC73HCH1H121J C CAPACITOR 120pF 50V JC392 CK73HBB1H102K C CAPACITOR 1000pF 50V KC395 CC73HCH1H2R5B C CAPACITOR 2.5pF 50V BC401 CK73HB1H103K C CAPACITOR 10000pF 50V KC402 CC73JCH1H101J C CAPACITOR 100pF 50V JC403 C93-1953-05 C CAPACITOR 0.01uF 25VC404 CK73HB1H103K C CAPACITOR 10000pF 50V KC405 CC73JCH1H101J C CAPACITOR 100pF 50V JC406 CK73HB1H103K C CAPACITOR 10000pF 50V KC407 C93-1953-05 C CAPACITOR 0.01uF 25VC408 CC73HCH1H050B C CAPACITOR 5pF 50V BC421 C93-1959-05 C CAPACITOR 0.1uF 16VC422 CC73HCH1H180G C CAPACITOR 18pF 50V GC423 CC73HCH1H150G C CAPACITOR 15pF 50V GC424 CK73HB1A224K C CAPACITOR 0.22uF 10V KC425 C93-1959-05 C CAPACITOR 0.1uF 16VC426 C93-1959-05 C CAPACITOR 0.1uF 16VC427 C93-1959-05 C CAPACITOR 0.1uF 16VC428 C93-1959-05 C CAPACITOR 0.1uF 16VC429 CK73FB1C106K C CAPACITOR 10uF 16V KC430 CK73FB1C106K C CAPACITOR 10uF 16V KC431 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC432 CK73FB1C106K C CAPACITOR 10uF 16V KC433 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC434 C93-1959-05 C CAPACITOR 0.1uF 16VC435 C93-1959-05 C CAPACITOR 0.1uF 16VC436 CK73FB1C106K C CAPACITOR 10uF 16V KC437 C93-1959-05 C CAPACITOR 0.1uF 16VC438 C93-1959-05 C CAPACITOR 0.1uF 16VC439 C93-1959-05 C CAPACITOR 0.1uF 16VC440 C93-1959-05 C CAPACITOR 0.1uF 16VC441 C93-1959-05 C CAPACITOR 0.1uF 16VC442 C93-1959-05 C CAPACITOR 0.1uF 16VC443 C93-1959-05 C CAPACITOR 0.1uF 16V
Symbol No. Part No. Part Name Description Local
C444 C93-1959-05 C CAPACITOR 0.1uF 16VC445 CK73HB1A105K C CAPACITOR 1uF 10V KC446 C93-1959-05 C CAPACITOR 0.1uF 16VC447 CC73JCH1H101J C CAPACITOR 100pF 50V JC448 CK73HB1H103K C CAPACITOR 10000pF 50V KC449 C93-1953-05 C CAPACITOR 0.01uF 25VC450 C93-1959-05 C CAPACITOR 0.1uF 16VC451 C93-1959-05 C CAPACITOR 0.1uF 16VC452 CK73HB1A105K C CAPACITOR 1uF 10V KC453 CK73HB1H103K C CAPACITOR 10000pF 50V KC454 CK73HB1E104K C CAPACITOR 0.10uF 25V KC455 CC73JCH1H101J C CAPACITOR 100pF 50V JC456 C93-1967-05 C CAPACITOR 470pF 50VC457 CC73JCH1H101J C CAPACITOR 100pF 50V JC458 CC73JCH1H101J C CAPACITOR 100pF 50V JC459 CC73JCH1H101J C CAPACITOR 100pF 50V JC469 C93-1967-05 C CAPACITOR 470pF 50VC470 C93-1967-05 C CAPACITOR 470pF 50VC471 C93-1967-05 C CAPACITOR 470pF 50VC472 C93-1967-05 C CAPACITOR 470pF 50VC473 C93-1967-05 C CAPACITOR 470pF 50VC474 C93-1967-05 C CAPACITOR 470pF 50VC475 C93-1967-05 C CAPACITOR 470pF 50VC476 C93-1967-05 C CAPACITOR 470pF 50VC477 C93-1967-05 C CAPACITOR 470pF 50VC480 CC73JCH1H101J C CAPACITOR 100pF 50V JC481 CC73JCH1H101J C CAPACITOR 100pF 50V JC482 CC73JCH1H101J C CAPACITOR 100pF 50V JC483 CC73JCH1H101J C CAPACITOR 100pF 50V JC484 CC73JCH1H101J C CAPACITOR 100pF 50V JC485 CC73JCH1H101J C CAPACITOR 100pF 50V JC486 CC73JCH1H101J C CAPACITOR 100pF 50V JC487 CC73JCH1H101J C CAPACITOR 100pF 50V JC488 CC73JCH1H101J C CAPACITOR 100pF 50V JC489 CC73JCH1H101J C CAPACITOR 100pF 50V JC496 CK73HB1A105K C CAPACITOR 1uF 10V KC497 C93-1959-05 C CAPACITOR 0.1uF 16VC498 C93-1959-05 C CAPACITOR 0.1uF 16VC499 C93-1959-05 C CAPACITOR 0.1uF 16VC500 C93-1959-05 C CAPACITOR 0.1uF 16VC501 CK73HB1A105K C CAPACITOR 1uF 10V KC502 C93-1959-05 C CAPACITOR 0.1uF 16VC510 C93-1967-05 C CAPACITOR 470pF 50VC515 C93-1967-05 C CAPACITOR 470pF 50VC516 CK73HB1E104K C CAPACITOR 0.10uF 25V KC517 CK73HB1E104K C CAPACITOR 0.10uF 25V KC518 CK73HB1E104K C CAPACITOR 0.10uF 25V KC601 CK73HB1E104K C CAPACITOR 0.10uF 25V KC602 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC603 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC604 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC606 CK73HB1A105K C CAPACITOR 1uF 10V KC607 CK73HB1A105K C CAPACITOR 1uF 10V KC608 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC609 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC610 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC612 CK73HB1A105K C CAPACITOR 1uF 10V KC615 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC617 CC73JCH1H101J C CAPACITOR 100pF 50V JC618 CC73JCH1H101J C CAPACITOR 100pF 50V JC620 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC621 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC622 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC625 CK73HB1A334K C CAPACITOR 0.33uF 10V KC626 CK73HB1H103K C CAPACITOR 10000pF 50V KC627 CK73HB1A334K C CAPACITOR 0.33uF 10V KC657 CC73HCH1H101J C CAPACITOR 100pF 50V JC658 CC73HCH1H101J C CAPACITOR 100pF 50V JC659 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC663 CK73GXR0J475K C CAPACITOR 4.7uF 6.3V KC664 CK73EXR0J476M C CAPACITOR 47uF 6.3V MC666 CK73HB1A224K C CAPACITOR 0.22uF 10V KC667 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC669 CK73FXR0J226M C CAPACITOR 22uF 6.3V MC671 CK73HBB1C683K C CAPACITOR 0.068uF 16V KC672 CK73GB1E104K C CAPACITOR 0.1uF 25V KC673 CK73HB1E104K C CAPACITOR 0.10uF 25V KC674 CK73GB1E105K C CAPACITOR 1uF 25V K
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-13
C675 CK73EXR0J476M C CAPACITOR 47uF 6.3V MC676 CK73FXR1E475K C CAPACITOR 4.7uF 25V KC677 CC73HCH1H221J C CAPACITOR 220pF 50V JC679 CC73HCH1H221J C CAPACITOR 220pF 50V JC681 CC73HCH1H101J C CAPACITOR 100pF 50V JC683 CK73HB1E104K C CAPACITOR 0.10uF 25V KC684 CC73HCH1H221J C CAPACITOR 220pF 50V JC686 CK73GB1E105K C CAPACITOR 1uF 25V KC687 CK73HB1E104K C CAPACITOR 0.10uF 25V KC688 CK73HB1A105K C CAPACITOR 1uF 10V KC689 CC73HCH1H470G C CAPACITOR 47pF 50V GC690 CC73HCH1H221J C CAPACITOR 220pF 50V JC691 CK73GXR1C225K C CAPACITOR 2.2uF 16V KC692 CK73GB1E104K C CAPACITOR 0.1uF 25V KC693 C93-1967-05 C CAPACITOR 470pF 50VC695 C93-1967-05 C CAPACITOR 470pF 50VC697 C93-1953-05 C CAPACITOR 0.01uF 25VC698 C93-1953-05 C CAPACITOR 0.01uF 25V
R1 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR7 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR8 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR9 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR10 RK73HH1J184D MG RESISTOR 180kΩ 1/16W DR11 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR12 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR13 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR14 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR15 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR16 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR17 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR18 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR19 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR20 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR21 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR22 RK73HH1J183D MG RESISTOR 18kΩ 1/16W DR23 RK73HH1J683D MG RESISTOR 68kΩ 1/16W DR24 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR25 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR26 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR27 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR28 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR29 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR30 RK73HH1J274D MG RESISTOR 270kΩ 1/16W DR31 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR32 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR33 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR34 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR35 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR36 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR37 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR38 RZ73G0BK2R7J RESISTOR 2.7Ω 0.25W JR39 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR40 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR41 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR42 R92-3774-05 MG RESISTOR 27Ω 0.25WR43 R92-3774-05 MG RESISTOR 27Ω 0.25WR44 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR45 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR46 RK73GB2A220J MG RESISTOR 22Ω 1/10W JR47 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR48 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR49 RK73JB1H474J MG RESISTOR 470kΩ 1/20W JR50 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR51 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR52 RK73FB2B1R0J MG RESISTOR 1Ω 1/8W JR56 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR57 RK73HH1J183D MG RESISTOR 18kΩ 1/16W DR58 RK73HH1J223D MG RESISTOR 22kΩ 1/16W DR59 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR60 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR65 RK73HH1J474D MG RESISTOR 470kΩ 1/16W DR66 RK73HH1J474D MG RESISTOR 470kΩ 1/16W DR102 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR103 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR104 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR105 RK73HB1J124J MG RESISTOR 120kΩ 1/16W JR106 RK73HB1J100J MG RESISTOR 10Ω 1/16W J
Symbol No. Part No. Part Name Description Local
R107 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR108 RK73HB1J106J MG RESISTOR 10MΩ 1/16W JR109 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR110 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR111 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W JR112 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR114 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR115 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR116 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR117 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR118 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR119 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR120 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR121 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR122 RK73HB1J562J MG RESISTOR 5.6kΩ 1/16W JR123 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR124 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR125 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR126 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR127 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR128 RK73HH1J391D MG RESISTOR 390Ω 1/16W DR129 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR130 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR131 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR132 RN73HH1J103D MF RESISTOR 10kΩ 0.063W DR133 RN73HH1J562D MF RESISTOR 5.6kΩ 0.063W DR134 RN73H0AJ121D MF RESISTOR 120Ω DR135 RK73HB1J8R2J MG RESISTOR 8.2Ω 1/16W JR136 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR137 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR139 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR140 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR141 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR142 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR143 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR151 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR152 RN73HH1J562D MF RESISTOR 5.6kΩ 0.063W DR153 RN73HH1J103D MF RESISTOR 10kΩ 0.063W DR154 RN73HH1J151D MG RESISTOR 150Ω 0.063W DR155 RK73HB1J4R7J MG RESISTOR 4.7Ω 1/16W JR156 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR181 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR182 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR183 RK73HB1J682J MG RESISTOR 6.8kΩ 1/16W JR184 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR194 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR195 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR204 R92-3785-05 MG RESISTOR 120Ω 0.25WR205 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR206 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR207 RK73HB1J330J MG RESISTOR 33Ω 1/16W JR208 RK73HB1J181J MG RESISTOR 180Ω 1/16W JR209 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR210 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR211 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR212 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR213 RK73HB1J121J MG RESISTOR 120Ω 1/16W JR214 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR215 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR216 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR218 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR219 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR221 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR222 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR223 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR224 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR225 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR227 RK73GB2A823J MG RESISTOR 82kΩ 1/10W JR228 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR230 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR233 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR234 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR237 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR244 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR245 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR246 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR247 RK73HB1J470J MG RESISTOR 47Ω 1/16W JR248 R92-3756-05 MG RESISTOR 0.22Ω 1/3W
Symbol No. Part No. Part Name Description Local
3-14(No.RA053<Rev.001>)
R249 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR250 R92-3756-05 MG RESISTOR 0.22Ω 1/3WR251 RK73HB1J270J MG RESISTOR 27Ω 1/16W JR252 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR253 RK73HH1J472D MG RESISTOR 4.7kΩ 1/16W DR255 RK73HH1J393D MG RESISTOR 39kΩ 1/16W DR256 RK73HH1J682D MG RESISTOR 6.8kΩ 1/16W DR257 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR258 RK73HB1J332J MG RESISTOR 3.3kΩ 1/16W JR259 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR260 RK73HB1J392J MG RESISTOR 3.9kΩ 1/16W JR264 RK73HH1J682D MG RESISTOR 6.8kΩ 1/16W DR265 RK73HH1J393D MG RESISTOR 39kΩ 1/16W DR266 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR267 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR268 RK73HB1J104J MG RESISTOR 100kΩ 1/16W JR269 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR270 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR301 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR302 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR303 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR304 RK73HB1J821J MG RESISTOR 820Ω 1/16W JR310 RK73HB1J391J MG RESISTOR 390Ω 1/16W JR312 RK73HB1J5R6J MG RESISTOR 5.6Ω 1/16W JR313 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR314 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR315 RK73HB1J120J MG RESISTOR 12Ω 1/16W JR316 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR325 RK73HH1J473D MG RESISTOR 47kΩ 1/16W DR330 RK73HH1J273D MG RESISTOR 27kΩ 1/16W DR331 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR332 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR333 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR335 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR336 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR351 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR352 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR353 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR354 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR355 RK73HB1J390J MG RESISTOR 39Ω 1/16W JR356 RK73HB1J151J MG RESISTOR 150Ω 1/16W JR357 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR358 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR359 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR360 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR361 RK73JB1H473J MG RESISTOR 47kΩ 1/20W JR362 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR363 RK73HB1J221J MG RESISTOR 220Ω 1/16W JR364 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR365 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR366 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR367 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR369 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR401 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR402 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR403 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR404 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR405 RK73HB1J153J MG RESISTOR 15kΩ 1/16W JR406 RK73HB1J333J MG RESISTOR 33kΩ 1/16W JR407 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR408 RK73HB1J681J MG RESISTOR 680Ω 1/16W JR410 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR411 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR412 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR413 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR414 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR415 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR419 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR420 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR421 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR422 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR423 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR424 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR425 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR426 RK73JB1H102J MG RESISTOR 1kΩ 1/20W JR427 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR428 RK73JB1H220J MG RESISTOR 22Ω 1/20W JR429 RK73JB1H102J MG RESISTOR 1kΩ 1/20W J
Symbol No. Part No. Part Name Description Local
R430 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR431 RK73HB1J223J MG RESISTOR 22kΩ 1/16W JR432 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR433 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR434 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR435 RK73JB1H105J MG RESISTOR 1MΩ 1/20W JR436 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR437 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR438 RK73GH2A49R9D MG RESISTOR 49.9Ω 1/10W DR439 RK73HH1J102D MG RESISTOR 1kΩ 1/16W DR440 RK73HH1J102D MG RESISTOR 1kΩ 1/16W DR441 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR442 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR443 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR444 RK73JB1H104J MG RESISTOR 100kΩ 1/20W JR445 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR446 RK73HB1J100J MG RESISTOR 10Ω 1/16W JR447 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR448 RK73JB1H222J MG RESISTOR 2.2kΩ 1/20W JR449 RK73JB1H472J MG RESISTOR 4.7kΩ 1/20W JR450 RK73HB1J331J MG RESISTOR 330Ω 1/16W JR451 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR452 RK73GB2A000J MG RESISTOR 0Ω 1/10W JR461 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR462 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR463 RK73HH1J104D MG RESISTOR 100kΩ 1/16W DR464 RK73HH1J103D MG RESISTOR 10kΩ 1/16W DR466 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR467 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR468 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR469 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR470 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR479 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR480 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR601 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR602 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR604 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR605 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR608 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR609 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR610 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR617 RK73HB1J822J MG RESISTOR 8.2kΩ 1/16W JR635 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR636 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR637 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR638 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR639 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR650 RK73HB1J683J MG RESISTOR 68kΩ 1/16W JR651 RK73HB1J152J MG RESISTOR 1.5kΩ 1/16W JR652 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR653 RK73JB1H101J MG RESISTOR 100Ω 1/20W JR654 RK73GB2A471J MG RESISTOR 470Ω 1/10W JR655 RK73JB1H103J MG RESISTOR 10kΩ 1/20W JR656 RK73PB2H1R2J MG RESISTOR 1.2Ω 1/2W JR657 RK73HB1J474J MG RESISTOR 470kΩ 1/16W JR658 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR659 RK73HB1J561J MG RESISTOR 560Ω 1/16W JR661 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR663 RK73HB1J101J MG RESISTOR 100Ω 1/16W JR664 RK73HB1J274J MG RESISTOR 270kΩ 1/16W JR665 RK73HB1J334J MG RESISTOR 330kΩ 1/16W JR667 RK73JB1H224J MG RESISTOR 220kΩ 1/20W JR668 RK73JB1H681J MG RESISTOR 680Ω 1/20W JR670 RK73HB1J220J MG RESISTOR 22Ω 1/16W JR672 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR676 RK73HB1J273J MG RESISTOR 27kΩ 1/16W JR678 RK73HB1J473J MG RESISTOR 47kΩ 1/16W JR680 RK73HB1J471J MG RESISTOR 470Ω 1/16W JR681 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR682 RK73HB1J224J MG RESISTOR 220kΩ 1/16W JR683 RK73HB1J103J MG RESISTOR 10kΩ 1/16W JR684 RK73HB1J272J MG RESISTOR 2.7kΩ 1/16W JR685 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J
L1 LB73F0AW-002 CHIP FERRITEL3 LB73G0AM-004 CHIP FERRITEL4 LR73Z0AY2R2M CHIP INDUCTORL5 LB73G0AM-004 CHIP FERRITE
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-15
L6 LB73G0AM-004 CHIP FERRITEL7 LB73G0AM-004 CHIP FERRITEL8 LB73G0AM-004 CHIP FERRITEL9 LB73H0AV-002 CHIP FERRITEL10 LB73H0AV-002 CHIP FERRITEL11 LB73H0AV-002 CHIP FERRITEL12 L41-1502-70 CHIP INDUCTORL13 LB73H0AV-002 CHIP FERRITEL111 LB73H0AY-004 CHIP FERRITEL112 LB73H0AY-004 CHIP FERRITEL121 LB73H0AY-004 CHIP FERRITEL131 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL132 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL133 LR79Z0GJ4N7G CHIP INDUCTORL134 L3C-0002-00 OSC-COILL135 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL136 L41-1085-53 CHIP INDUCTORL137 L41-1085-53 CHIP INDUCTORL138 L41-1085-53 CHIP INDUCTORL151 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL152 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL153 LK73H0AMR10J M.CHIP INDUCTOR 0.1uHL154 LR79Z0GJ5N1G CHIP INDUCTORL155 L3C-0001-00 OSC-COILL156 L41-1585-53 CHIP INDUCTORL157 L41-1585-53 CHIP INDUCTORL158 L41-1585-53 CHIP INDUCTORL181 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL191 LK73H0AM5N6S M.CHIP INDUCTOR 5.6nHL192 LK73H0AM4N7S M.CHIP INDUCTOR 4.7nHL201 LR79Z0DD21N9J CHIP INDUCTOR 21.9nHL202 LR79G0CQ3N9C CHIP INDUCTORL203 LR79Z0CAR22J CHIP INDUCTOR 0.22uHL204 LR79G0GKR12G CHIP INDUCTORL205 LK73H0AM12NJ M.CHIP INDUCTOR 12nHL206 LK73H0AMR12J M.CHIP INDUCTOR 0.12uHL207 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL208 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL209 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL210 LR79G0GK9N1C CHIP INDUCTORL211 LB73G0AM-004 CHIP FERRITEL212 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL213 LR79Z0DC45N5J CHIP INDUCTOR 45.5nHL214 LB73F0AW-002 CHIP FERRITEL215 LR79Z0DD16N9J CHIP INDUCTOR 16.9nHL216 LR79Z0DD16N9J CHIP INDUCTOR 16.9nHL217 LR79Z0DD16N9J CHIP INDUCTOR 16.9nHL218 LR79Z0CA39NG CHIP INDUCTOR 39nHL301 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL302 LR79G0CQ10NG CHIP INDUCTORL303 LK73H0AMR27J M.CHIP INDUCTORL304 LK73H0AM33NJ M.CHIP INDUCTOR 33nHL307 LR79G0CQ12NG CHIP INDUCTORL308 LR79G0CQ7N5C CHIP INDUCTORL309 LR79G0CQ22NG CHIP INDUCTOR 22nHL310 LR79G0CQ3N9C CHIP INDUCTORL311 LR79G0CQ39NG CHIP INDUCTORL312 LR79G0CQ39NG CHIP INDUCTORL313 LR79G0CQ39NG CHIP INDUCTORL314 LR79G0CQ22NG CHIP INDUCTOR 22nHL315 LR79G0CQR22G CHIP INDUCTORL351 L92-0487-05 CHIP FERRITEL352 L92-0487-05 CHIP FERRITEL353 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL354 LK73H0AM27NJ M.CHIP INDUCTOR 27nHL358 L92-0487-05 CHIP FERRITEL359 L7K-0059-00 FILTERL361 L79-1987-05 FILTERL365 L92-0487-05 CHIP FERRITEL366 L92-0487-05 CHIP FERRITEL401 LB73H0AV-002 CHIP FERRITEL402 LK73G0AQ4R7K M.CHIP INDUCTOR 4.7uHL404 LB73G0AM-004 CHIP FERRITEL405 L92-1101-05 CHIP FERRITEL406 L92-1101-05 CHIP FERRITEL407 LB73G0AM-004 CHIP FERRITEL408 LB73G0AM-004 CHIP FERRITEL409 LB73G0AM-004 CHIP FERRITE
Symbol No. Part No. Part Name Description Local
L410 LB73G0AM-004 CHIP FERRITEL411 L79-1946-05 FILTERL412 L79-1946-05 FILTERL413 L79-1946-05 FILTERL414 L79-1946-05 FILTERL415 L79-1946-05 FILTERL416 L79-1946-05 FILTERL417 LB73H0AV-002 CHIP FERRITEL427 LB73H0AV-002 CHIP FERRITEL428 LB73H0AV-002 CHIP FERRITEL429 LB73H0AV-002 CHIP FERRITEL430 LB73H0AV-002 CHIP FERRITEL431 LB73H0AV-002 CHIP FERRITEL601 LB73G0AM-004 CHIP FERRITEL604 LB73G0AM-004 CHIP FERRITEL605 LB73G0AM-004 CHIP FERRITEL608 LR73Z0AY100M CHIP INDUCTORL609 LR73Z0AY100M CHIP INDUCTORL610 LB73G0AM-004 CHIP FERRITEL612 LB73G0AM-004 CHIP FERRITEL613 LB73G0AM-004 CHIP FERRITEL622 LB73G0AM-004 CHIP FERRITEL623 LB73G0AM-004 CHIP FERRITEL635 LB73H0AV-002 CHIP FERRITE
CN1 EC720CQ-0313A FFC FPC CONNECTORCN2 J19-5386-05 HOLDERCN7 E40-6883-05 F.C.CONNECTORCN8 ------------ TERMINAL *NoteCN10 ------------ TERMINAL *NoteCN201 E2D-0058-00 TERMINALCN202 E2D-0058-00 TERMINALCN353 G0B-0005-00 EARTH SPRINGCN354 G0B-0005-00 EARTH SPRINGCN356 G0B-0005-00 EARTH SPRINGCN357 G0B-0005-00 EARTH SPRINGCN402 EC720BP-0341A FFC FPC CONNECTORCN602 E41-1476-05 PIN ASSYCP1 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP2 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP301 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP302 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP303 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP351 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP352 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP401 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP402 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP403 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP404 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP405 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP406 RK74HB1J100J NET RESISTOR 10Ω 1/16W JCP408 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP409 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP410 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP411 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP412 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP413 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP414 RK74HB1J101J NET RESISTOR 100Ω 1/16W JCP601 RK74HB1J100J NET RESISTOR 10Ω 1/16W JE101 ------------ SHIELDING CASE *NoteE301 ------------ SHIELDING CASE *NoteE351 F10-3228-15 SHIELDING CASEE401 ------------ SHIELDING CASE *NoteE601 ------------ SHIELDING CASE *NoteF1 FZA10BQ-3R15 FUSE (CC)F2 FZA10BH-R50 FUSE (CC) 0.5AF650 FZA10BH-R315 FUSE (CC) 0.315AJ651 E1B-0019-00 3.5D PHONE JACKJ652 E1B-0020-00 2.5D PHONE JACKTH201 NCU15WF104F6S N THERMISTORTH401 NCU15WF104F6S N THERMISTORX351 L77-3121-05 QUARTZ CRYSTALX401 L7H-0076-00 TCXOX402 L77-1802-05 QUARTZ CRYSTAL
Symbol No. Part No. Part Name Description Local
3-16(No.RA053<Rev.001>)
DISPLAY UNITXC1-209K-00 (NX-3220(K),NX-3220(E3),NX-3320(K),NX-3320(E3))
XC1-209K-01 (NX-3220(K2),NX-3220(E2),NX-3320(K2),NX-3320(E2))
XC1-209K-02 (NX-3220(K3),NX-3220(E),NX-3320(K3),NX-3320(E))
*Note : This part cannot be replaced.Therefore, this part is not supplied as a service part.
Block No. [0][3]
Symbol No. Part No. Part Name Description Local
IC201 TC7SZ08FE IC 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
Q141 EMD9 DIGI TRANSISTOR3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
Q201 EMD9 DIGI TRANSISTOR 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
Q221 LTC014EEBFS8 DIGI TRANSISTORQ222 LTC014EEBFS8 DIGI TRANSISTORQ223 LTC014EEBFS8 DIGI TRANSISTORQ227 LTC014EEBFS8 DIGI TRANSISTORQ228 LTC014EEBFS8 DIGI TRANSISTORQ229 LTC014EEBFS8 DIGI TRANSISTOR
D111 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D112 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D113 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D114 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D115 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D116 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D117 B30-2365-05 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D118 B30-2365-05 LED 3220K3,3220E,3320K3,3320ED119 B30-2365-05 LED 3220K3,3220E,3320K3,3320ED120 B30-2365-05 LED 3220K3,3220E,3320K3,3320ED132 B30-2365-05 LED 3220K2,3220E2,3320K2,3320E2
D141 RB521SM-30 DIODE3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D142 RB521SM-30 DIODE3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D143 RB521SM-30 DIODE3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D144 RB521SM-30 DIODE 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D180 RN262CS DIODED181 RN262CS DIODE
D201 NSSW206C-T865 LED3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D202 NSSW206C-T865 LED 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
D221 NESM238B LEDD227 NESM238B LED
C101 CK73HBB1H471K C CAPACITOR 470pF 50V KC102 CK73HBB1H471K C CAPACITOR 470pF 50V K
C141 CK73HBB1H471K C CAPACITOR 470pF 50V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C142 CK73HBB1H471K C CAPACITOR 470pF 50V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C143 CK73HBB1H471K C CAPACITOR 470pF 50V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C144 CK73HBB1H471K C CAPACITOR 470pF 50V K 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C145 CK73HBB1H471K C CAPACITOR 470pF 50V KC146 CK73HBB1H471K C CAPACITOR 470pF 50V K
C147 CK73HBB1H471K C CAPACITOR 470pF 50V KC148 CK73HBB1H471K C CAPACITOR 470pF 50V KC149 CK73HBB1H471K C CAPACITOR 470pF 50V KC158 CC73HCH1H220J C CAPACITOR 22pF 50V JC172 CC73HCH1H040B C CAPACITOR 4pF 50V BC175 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC177 CC73HCH1H010B C CAPACITOR 1pF 50V BC179 CC73HCH1H1R5B C CAPACITOR 1.5pF 50V BC184 CK73HBB1H102K C CAPACITOR 1000pF 50V KC186 CK73HBB1H102K C CAPACITOR 1000pF 50V KC190 CC73HCH1H010B C CAPACITOR 1pF 50V BC192 CC73HCH1H121J C CAPACITOR 120pF 50V JC193 CK73HBB1H102K C CAPACITOR 1000pF 50V K
C201 CK73HB1E104K C CAPACITOR 0.10uF 25V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C202 CK73HB0J225K C CAPACITOR 2.2uF 6.3V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C203 CK73HB0J225K C CAPACITOR 2.2uF 6.3V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C204 CK73HB1E334K C CAPACITOR 0.33uF 25V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C205 CK73HB1E104K C CAPACITOR 0.10uF 25V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C206 CK73HB1E104K C CAPACITOR 0.10uF 25V K3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
C207 CK73HB1E104K C CAPACITOR 0.10uF 25V K 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R1 RK73HB1J000J MG RESISTOR 0Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R2 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3220K3,3220E,3320K3,3320ER3 RK73HB1J000J MG RESISTOR 0Ω 1/16W J
R111 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R112 RK73HB1J561J MG RESISTOR 560kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R113 RK73HB1J561J MG RESISTOR 560kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R114 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R115 RK73HB1J561J MG RESISTOR 560kΩ 1/16W J 3220K2,3220E2,3320K2,3320E2R115 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J 3220K3,3220E,3320K3,3320E
R116 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R117 RK73HB1J561J MG RESISTOR 560kΩ 1/16W J 3220K2,3220E2,3320K2,3320E2R117 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J 3220K3,3220E,3320K3,3320ER118 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W J 3220K3,3220E,3320K3,3320ER119 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W J 3220K3,3220E,3320K3,3320ER120 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W J 3220K3,3220E,3320K3,3320ER121 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3220K2,3220E2,3320K2,3320E2R122 RK73HB1J000J MG RESISTOR 0Ω 1/16W J 3220K3,3220E,3320K3,3320ER132 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J 3220K2,3220E2,3320K2,3320E2
R141 RK73HB1J472J MG RESISTOR 4.7kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R142 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K3,3220E,3320K3,3320ER143 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K3,3220E,3320K3,3320ER145 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K3,3220E,3320K3,3320ER146 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K2,3220E2,3320K2,3320E2R147 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K3,3220E,3320K3,3320E
R148 RK73HB1J101J MG RESISTOR 100Ω 1/16W J 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R155 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR170 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR174 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR183 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR185 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR189 RK73HB1J000J MG RESISTOR 0Ω 1/16W JR191 RK73HB1J000J MG RESISTOR 0Ω 1/16W J
R201 RK73HB1J101J MG RESISTOR 100Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R203 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R204 RK73GB2A221J MG RESISTOR 220Ω 1/10W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R205 RK73GB2A221J MG RESISTOR 220Ω 1/10W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R206 RK73HB1J101J MG RESISTOR 100Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
Symbol No. Part No. Part Name Description Local
(No.RA053<Rev.001>)3-17
R207 RK73HB1J000J MG RESISTOR 0Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R208 RK73HB1J103J MG RESISTOR 10kΩ 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
R209 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W J 3220K,3220E3,3320K,3320E3R221 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR222 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W JR223 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR227 RK73HB1J102J MG RESISTOR 1kΩ 1/16W JR228 RK73HB1J122J MG RESISTOR 1.2kΩ 1/16W JR229 RK73HB1J271J MG RESISTOR 270Ω 1/16W JR230 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR231 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W JR232 RK73HB1J222J MG RESISTOR 2.2kΩ 1/16W J
L101 LB73H0AV-002 CHIP FERRITEL102 LB73H0AV-002 CHIP FERRITEL151 LK73H0AM15NJ M.CHIP INDUCTOR 15nHL152 LK73H0AM6N8J M.CHIP INDUCTOR 6.8nHL153 LK73H0AM12NJ M.CHIP INDUCTOR 12nHL156 LK73H0AM1N2S M.CHIP INDUCTORL173 LK73H0AM4N7S M.CHIP INDUCTOR 4.7nHL176 LK73H0BJ3N9S M.CHIP INDUCTORL178 LK73H0BJ3N9S M.CHIP INDUCTORL187 LK73H0AM10NJ M.CHIP INDUCTOR 10nHL194 LK73H0AM27NJ M.CHIP INDUCTOR 27nH
L201 LB73H0AV-002 CHIP FERRITE3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
L202 LB73H0AV-002 CHIP FERRITE 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
A151 ------------ CIRCUIT MODULE *Note
CN201 EC720BP-0325A FFC FPC CONNECTOR 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
CN202 EC720BP-0341A FFC FPC CONNECTORCN301 E40-6883-05 F.C.CONNECTOR
CP141 RK74HB1J101J NET RESISTOR 100Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
CP201 RK74HB1J101J NET RESISTOR 100Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
CP202 RK74HB1J101J NET RESISTOR 100Ω 1/16W J3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
CP203 RK74HB1J101J NET RESISTOR 100Ω 1/16W J 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
MIC101 T9B-0004-00 MIC ELEMENT
S111 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S112 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S113 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S114 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES115 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES116 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES117 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES118 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320E
S119 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S120 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S121 S70-0901-05 TACTILE PUSH SW3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
S122 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES123 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES124 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES125 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES126 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES127 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES128 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES129 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES130 S70-0901-05 TACTILE PUSH SW 3220K3,3220E,3320K3,3320ES131 S70-0901-05 TACTILE PUSH SW 3220K2,3220E2,3320K2,3320E2S132 S70-0901-05 TACTILE PUSH SW 3220K2,3220E2,3320K2,3320E2S301 S70-0516-05 TACTILE PUSH SWS302 S70-0516-05 TACTILE PUSH SWS303 S70-0516-05 TACTILE PUSH SWS304 S70-0516-05 TACTILE PUSH SW
Symbol No. Part No. Part Name Description Local
3-18(No.RA053<Rev.001>)
Packing materials and accessories parts list
Packing and accessoriesBlock No. [M][2][M][M]
Symbol No. Part No. Part Name Description Local
1 H1C-0175-00 PACKING FIXTURE 2 ------------ PROTECTION BAG ACC/CAP(x2) 3 ------------ PROTECTION BAG RADIO 4 H5A-1304-00 ITEM CARTON 5 J1K-0494-00 HOLDER ACC-2PIN PLUG 6 J29-0730-05 HOOK ACC-KBH-11 7 N09-6585-15 SPECIAL SCREW ACC-HOOK(x2) 8 B5A-2071-00 INST.MANUAL ACC-3 LANG 3220K,3220K2,3220K3,3320K,3320K2,3320K3 8 B5A-2072-00 INST.MANUAL ACC-9 LANG 3220E,3220E2,3220E3,3320E,3320E2,3320E3 9 N1Y-0037-00 INS.WASHER ACC-2PIN/HOLDER 10 N0Y-0017-00 DRESSED SCREW ACC-2PIN/CAP 11 N0Y-0018-00 DRESSED SCREW ACC-2PIN/HOLDER 12 B0K-0077-00 CAP 2PIN 13 G1D-0231-00 CUSHION 14 D32-0454-04 STOPPER CH KNOB 3220K2,3220K3,3220E,3220E2,3320K2,3320K3,3320E,3320E2
12
8
3
4
6
7
10
2
1
Block No.M2MM
14
5
2
11
139
(No.RA053<Rev.001>)3-19
(No.RA053<Rev.001>)
JKS
Printed in Japan
JVC KENWOOD CorporationCommunications Systems Division