Service Manual Travel Mate 230

TravelMate 230/ 280Service Guide

PART NO.: 49.46W01.001

PRINTED IN TAIWAN

II

Revision HistoryPlease refer to the table below for the updates made on HP Lapin service guide.

Date Chapter Updates01/20/2003 Cover page Correct typo on page II

Dual high quality stereo speakers on page 2

Modify item 3 media activity on page 12

Supports memory size per socket: 512MB on page 19

USB Compliancy Level: USB 2.0 on page 25

Chapter 2 Modify Flash BIOS procedures

Delete "Removing HDD password procedures"

Chapter 3 Mark the size of the flat-bladed screwdriver and hexed screwdriver

Correct the disassembly procedure of HDD module.

Chapter 4 Modify wording: If an error occurs with the internal diskette drive, first turn off the power and then reconnect the diskette connector to the system board.

Chapter 5 Modify Switch Setting

02/08/2003 Chapter 1 Delete dual display feature

04/14/2003 Chapter 1 Delete RS-232 serial port connectivity feature

III

CopyrightCopyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

DisclaimerThe information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Intel is a registered trademark of Intel Corporation.Pentium and Pentium II/III are trademarks of Intel Corporation.Other brand and product names are trademarks and/or registered trademarks of their respective holders.

ConventionsThe following conventions are used in this manual:

Screen messages Denotes actual messages that appear on screen.

NOTE Gives bits and pieces of additional information related to the current topic.

WARNING Alerts you to any damage that might result from doing or not doing specific actions.

CAUTION Gives precautionary measures to avoid possible hardware or software problems.

IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.

IV

PrefaceBefore using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

V

VI

Table of Contents
Chapter 1 System Introduction 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 2 System Utilities 33

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Multi-Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Boot Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52System Utility Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53System Diagnostic Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Chapter 3 Machine Disassembly and Replacement 57

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63Removing the Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65Removing the Modem Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66Disassembling the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79System Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Chapter 4 Troubleshooting 93

System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . .98Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . .102Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106Index of Phlash16 Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107Index of PQA Diagnostic Error Code, Message . . . . . . . . . . . . . . . . . . . . . . . .109

Chapter 5 Jumper and Connector Locations 111

Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

Chapter 6 FRU (Field Replaceable Unit) List 115

TravelMate 230 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116TravelMate 280 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125

Appendix A Model Definition and Configuration 135

Model Number Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135

Appendix B Test Compatible Components 137

Microsoft Windows XP Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138Microsoft Windows 2000 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . .142Microsoft Windows 98 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146

VII

Table of Contents
Appendix C Online Support Information 151
Index 153

VIII

Chapter 1 1

FeaturesThis computer was designed with the user in mind. Here are just a few of its many features:

Performance Intel® Mobile Celeron Pentium® 4 series processors from 1.6G up tp 2.0G with 512KB cache (TravelMate 230)

Intel® Mobile Northwood Pentium® 4 series processors from 1.6G up tp 2.4G with 512KB cache (TravelMate 280)

64-bit memory bus

Two 200-pin DDR-DRAM with each supporting 128MB/ 256MB/ 512MB, upgradable to the total maximum of 1024MB with SODIMM modules, supporting PC1600/2100 .

Built-in floppy diskette drive and Hard diskette drive

High-capacity, Enhanced-IDE hard disk

Simultaneous LCD and CRT display

Smart Lithium-Ion battery pack

Power management system with ACPI (Advanced Configuration Power Interface)

Plug and Play Feature

Multimedia16-bit high-fidelity AC’97 stereo audio with 3D sound and wavetable synthesizer

Built-in dual speakers

High- speed CD-ROM, DVD-ROM, or DVD/ CD-R/RW drive

Connectivity84/85/88 key keyboard, which is PC/AT keyboard compatible.

Four Universal Serial Bus (USB) 2.0 Ports (Two ports optional)

Bluetooth (Optional)

Two IEEE 1394 ports (optional)

Built-in V.90 and V.92 RJ-11 56Kbps fax/modem

Onboard 10/100 Mbps Ethernet LAN Support

Upgradeable memory and hard disk

Mini PCI interface 802.11b/ 802.11a+b Module (optional)

ECP Compliant parallel port.

MultimediaAll-in-one design (CD-ROM, floppy disk drive, hard disk drive)

Sleek, smooth and stylish design

Full-sized keyboard

Ergonomically centered touchpad pointing device with Internet scroll key

System Introduction

Chapter 1

Expansion� One CardBus PC Card (formerly PCMCIA) Type III slot.

� Upgrageable memory and hard disk

I/O Ports

� One VGA port, I2 C compatible (Optional)

� One DC-in port (AC adapter)

� Dual high quality stereo speakers

� One line-in

� One line-out

� One CardBus type III slot (3.3V, 5V, 12V support)

� Four USB ports (2 ports optional)

� Two IEEE 1394 ports (optional)

� One ECP parallel port

� One RJ-11 port

� One RJ-45 jack

Display

� 14.1” and 15” TFT LCD displaying 32-bit true-color at 1024x768 XGA resolution

� 3D capabilities

� Supports other output display devices such as LCD projection panels for large audience presentations

� “Automatic LCD dim” feature that automatically decides the best settings for your display and conserves power is activated when the system operates in Battery condition.

Video performance

4X AGP UMA video graphic accelerator with 8MB shared from system memory with Intel 845GL to boost the video performance.

Simultaneous display

The computer’s large display and multimedia capabilities are great for giving presentations. If you prefer, you can also connect an external monitor when giving presentations. This computer has built-in AGP and VGA display system to support simultaneous LCD and CRT display. Simultaneous display allows you to control the presentation from your computer and at the same time face your audience. You can also connect other output display devices such as LCD projection panels for large-audience presentations.

Dual Display

The computer’s unique graphics chip takes advantage of Windows XP’s multi-display capability, allowing you to extend your desktop to an external display device, such as an external monitor projector. With this feature enabled, you can move program windows to/from the computer LCD and the external monitor.

Power management

The power management system incorporates an "automatic LCD dim" feature that automatically dims the LCD when the computer is powered by a battery pack to conserve battery power. See “Power Management” on page 28 for more information on power management features.

Chapter 1 2

Opening and closing the display

To open the display, slide the display cover latch to the right and lift up the cover. Then tilt it to a comfortable viewing position. The computer employs a microswitch that turns off the display (and enters standby mode) to conserve power when you close the display cover, and turns it back on when you open the display cover.

NOTE: If an external monitor is connected, the computer turns off the display (but does not enter standby mode) when you close the display cover.

To close the display cover, fold it down gently until the display cover latch clicks into place.

WARNING: To avoid damaging the display, do not slam it when you close it. Also, do not place any object on top of the computer when the display is closed.

3 TravelMate 230/ 280

System Block Diagram

CLK GENICS 94239

Mobile CPUP4-M NorthwoodP4-M Celeron

EXTERNAL SPEED STEP

CIRCUIT

G768D

DDR*2266MHz

CRT CONN

LCD

ICH4

HDD

AC ‘97CODECCS4299XQ

OP AMPTPA0202

MODEMMDC Card

INT. SPKRCD ROM

USBUSBBT.

VR

CARDBUSOZ 6912

LANREALTEK

8100BL

NS SIO PC87392

KBCM38859M38857

FWH 4MBSIOC32SOIC40

LPCDEBUGCONN.

PRNPort FDD

1394CONN

CARDBUSONE SLOT

NARI

MCHBrookdale-GL

PWR SWOZ2211S

AGERE 1394FW32305

MIC IN

Line In

Line Out

AUDIO

BOARD

AC-Link

PCI BUS

RGB

DVO LVDSChrontel7019

LPC BUS

PIDESIDE

HOST BUS 100MHz

HUB I/F 66MHz

TRACKPOINT INT KB

Dual Channel

MINI PCI802.11

SER.RES

INT. MIC

CLK GENICS 94239

Mobile CPUP4-M NorthwoodP4-M Celeron

EXTERNAL SPEED STEP

CIRCUIT

G768D

DDR*2266MHzDDR*2266MHz

CRT CONN

LCD

ICH4

HDD

AC ‘97CODECCS4299XQ

OP AMPTPA0202

MODEMMDC Card

INT. SPKRCD ROM

USBUSBBT.

VR

CARDBUSOZ 6912

LANREALTEK

8100BL

NS SIO PC87392

KBCM38859M38857

FWH 4MBSIOC32SOIC40

LPCDEBUGCONN.

PRNPort FDD

1394CONN

CARDBUSONE SLOT

NARI

MCHBrookdale-GL

PWR SWOZ2211S

AGERE 1394FW32305

MIC IN

Line In

Line Out

AUDIO

BOARD

AC-Link

PCI BUS

RGB

DVO LVDSChrontel7019

LPC BUS

PIDESIDE

HOST BUS 100MHz

HUB I/F 66MHz

TRACKPOINT INT KB

Dual Channel

MINI PCI802.11

SER.RES

INT. MIC

Chapter 1 4

Board Layout

Top View

PCB No. 02217-SB

1 CPU Socket 12 Mini-PCI Connector

2 CRT Port 13 RTC Battery Connector

3 Inverter Connector 14 SW1 Setting (Please see Chapter 5 for details)

4 RJ45 + RJ11 15 Internal Keyboard Cable Connector

5 Bluetooth Connector (Dummy) 16 CD-ROM Connector

6 USB Port 0 17 HDD Connector

7 LCD Coaxial Cable Connector 18 Golden Finger (or Debug Board)

8 USB Port 1 19 Touch Pad Cable Connector

9 Launch Cable Connector 20 FDD Connector

10 Parallel Port 21 CardBus Connector

11 DC-in Port 22 Fan Connector


Bottom View

1 Modem Cable Connector 7 Modem Connector

2 North Bridge (845-GL) 8 Battery Connector

3 DIMM Socket 1 9 CardBus Controller (OZ6912T)

4 Audio Board Connector 10 LAN Controller (RTL8100BL)

5 DIMM Socket 2 11 LVDS

6 South Bridge (ICH4)

Chapter 1 6

PanelPorts allow you to connect peripheral devices to your computer as you would with a desktop PC.

Front Panel

# Item Description

1 Display screen Also called LCD (Liquid Crystal Display), displays computer output.

2 Status indicators LEDs (Light Emitting Diodes) that turn on and off to show the status of the computer and its functions and components.

3 Touchpad Touch-sensitive pointing device which functions like a computer mouse.

4 Click button (left, center and right) The left and right buttons function like the left and right mouse buttons, the center button serves as a scroll up/down button.

5 Palmrest Comfortable support area for your hands when you use the computer.

6 Keyboard Inputs data into your computer.

7 Easy launch keys Buttons for launching frequently used programs.


Left Panel

# Icon Item/ Port Description

1 PCMCIA (PC card) Port Connects to one Type III 16-bit PC card or 32-bit CardBus PC Card.

2 Eject button Eject PC cards from the card slots.

3 Floppy activity indicator LED (light-emitting diodes) that turn on and off when the floppy is active.

4 Speaker/ headphone-out jack Connects to audio line-out devices (e.g., speakers, headphones)

5 Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).

6 Microphone-in jack Accepts a mono/stereo condenser microphone.

7 Floppy drive Internal diskette drive, accepts 3.5-inch floppy diskettes

8 Volume control Controls the volume of the speakers.

9 Floppy disk eject button Push this button to eject the floppy disk

Chapter 1 8

Right Panel

# Icon Item/ Port Description

1 Battery bay Houses the computer’s battery pack.

2 Optical drive Houses removable optical drive modules.

3 LED indicator Lights up when the optical drive is active.

4 Eject button Ejects the compact disc from the drive.

5 Emergency eject slot Ejects the compact discs when the computer is turned off.

6 Security keylock Kensington-compatible key-based computer security lock.


Rear Panel

# Icon Port Description

1 Power Jack Connects to an AC adapter

2 Parallel port Connects to a parallel device (e.g., parallel printer)

3 USB port (two) Connects to any Universal Serial Bus devices(e.g., USB mouse, USB camera).

4 Modem jack Connects to the phone line

5 Network jack Connects to an Ethernet 10/100-based network

6 External display port Connects to a display device (e.g., external monitor, LCD projector) and displays up to 64K colors at 1280x1024 resolution

Chapter 1 10

Bottom Panel

# Item Description

1 Battery bay Houses the computer’s battery pack.

2 Battery release latch Unlatches the battery to remove the battery pack.

3 Hard disk bay Houses the computer’s hard disk (secured by a screw).

4 Memory compartment Houses the computer’s main memory.


IndicatorsThe computer has six easy-to-read status icons on the right of the display screen.

The Power and Standby status icons are visible even when you close the display cover so you can see the status of the computer while the cover is closed.

# Icon Function Description

1 Power Lights when the computer is on.

2 Sleep Lights when the computer enters Standby mode and blinks when it enters into or resumes from hibernation mode.

3 Media Activity Lights when the floppy drive, hard disk or Media drive is active.

4 Battery Charge Lights when the battery is being charged.

5 Caps Lock Lights when Caps Lock is activated.

6 Num Lock

(Fn-F11)

Lights when Numeric Lock is activated.

Chapter 1 12

KeyboardThe keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys.

Special keys

Lock keys

The keyboard has three lock keys which you can toggle on and off.

Embedded numeric keypad

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.

Lock key Description

Caps Lock

@

When @is on, all alphabetic characters typed are in uppercase.

Num Lock (Fn-F11)

]

When ] is on, the embedded keypad is in numeric mode. The keys function

as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad.

Scroll Lock (Fn-F12)

[

When [ is on, the screen moves one line up or down when you press the up

or down arrow keys respectively. [ does not work with some applications.


NOTE: If an external keyboard or keypad is connected to the computer, the Num Lock feature automatically shifts from the internal keyboard to the external keyboard or keypad.

Windows keys

The keyboard has two keys that perform Windows-specific functions.

Desired access Num lock on Num lock off

Number keys on embedded keypad

Type numbers in a normal manner.

Cursor-control keys on embedded keypad

Hold Shift while using cursor-control keys. Hold Fn while using cursor-control keys.

Main keyboard keys Hold Fn while typing letters on embedded keypad.

Type the letters in a normal manner.

Keys Description

Windows logo key

�

Start button. Combinations with this key perform shortcut functions. Below are a few examples:

� + Tab (Activates next taskbar button)

� + E (Explores My Computer)

� + F (Finds Document)

� + M (Minimizes All)

j+ � + M (Undoes Minimize All)

� + R (Displays the Run... dialog box)

Application key Opens a context menu (same as a right-click).

Chapter 1 14

Hot KeysThe computer employs hot keys or key combinations to access most of the computer’s controls like screen contrast and brightness, volume output and the BIOS Utility.

To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination.

Hot Key Icon Function Description

Fn-l Hotkey help Displays a list of the hotkeys and their functions.

Fn-m Setup Accesses the notebook configuration utility.

Fn-n Power Scheme Toggle Switches between the power management scheme used by the computer (function available if supported by operating system).

Fn-o Sleep Puts the computer in Sleep mode.

Fn-p Display toggle Switches display output between the display screen, external monitor (if connected) and both the display screen and external monitor.

Fn-q Screen blank Turns the display screen backlight off to save power. Press any key to return.

Fn-r Touchpad Toggle Turns the internal touchpad on and off.

Fn-s Speaker on/off Turns the speakers on and off; mutes the sound.

Fn-w Contrast up Increases the screen contrast (available only for models with HPA displays).

Fn-y Contrast down Decreases the screen contrast (available only for models with HPA displays).

Fn-x Brightness up Increases the screen brightness.


The Euro symbol

If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a European layout, you can type the Euro symbol on your keyboard.

NOTE: for US keyboard users: The keyboard layout is set when you first set up Windows. For the Euro symbol to work, the keyboard layout has to be set to United States-international.

To verify the keyboard type:

1. Click on Start, Control Panel.

2. Double-click on Regional and Language Options.

3. Click on the language tab and click on Details.

4. Verify that the keyboard layout used for “EN English (United States) is set to United States-International.

If not, select and click on ADD, then select United States-International and click on OK.

5. Click on OK.

To type the Euro symbol:

1. Locate the Euro symbol on your keyboard.

2. Open a text editor or word processor.

3. Hold aGr and press the Euro symbol.

Fn-¨z Brightness down Decreases the screen brightness.

Fn-{ Home Functions as the g key.

Fn-} End Functions as the d key.

aGr-Euro Euro Types the Euro symbol.

Hot Key Icon Function Description

Chapter 1 16

Launch Keys

Located at the top of the keyboard are five buttons. These buttons are called launch keys. They are designated as wireless LAN/Bluetooth , Web Browser button, mail button, P1 andP2. By default, P1 and P2 are users programmable. The Web Browser button, by default, is used to launch the internet browser The mail button is used to launch the e-mail application. The LED of the mail button will flash when the user has received an incoming email.

# Icon Function Description

1 Wireless/ Bluetooth 802.11a/802.11b wireless LAN/Bluetooth (Optional)

2 Web browser Internet browser application

3 Mail Email application

4 P1 User-programmable

5 P2 User-programmable


Hardware Specifications and Configurations

System Board Major Chips

Item Controller

System core logic Intel ICH4

Super I/O controller Mitsubish 38857

Audio controller Cirrus CS4299XQ

Video controller Intel 845GL

Hard disk drive controller Embedded in Intel ICH4

Keyboard controller Mitsubish 38857

CardBus Controller OZ 6912T-U

RTC Intel ICH4

Processor (for TravelMate 230)

Item Specification

CPU type Intel Celeron Pentium® 4

CPU package To 2.0GHz uFCBGA

CPU core voltage 1.7V

CPU I/O voltage 1.25V

Processor (for TravelMate 280)

Item Specification

CPU type Intel Mobile Northood P4 with 512KB Cache

CPU package To 2.4GHz uFCBGA

CPU core voltage 1.7V

CPU I/O voltage 1.25V

BIOS

Item Specification

BIOS vendor Phoenix BIOS

BIOS Version R01XXX

BIOS ROM type Flash ROM

BIOS ROM size 512KB

BIOS package 32 Pin PLCC

Supported protocols ACPI 2.0 (if available, at least 1.0b), SMBIOS 2.3, PCI 2.2, Boot Block, PXE 2.0, Mobile PC2001, Hard Disk Password, INT 13h Extensions, PCI Bus Power Management interface Specification, EI Torito-Bootable CD-ROM Format Specification V1.0, Simple Boot Flag 1.0

BIOS password control Set by switch, see SW1 settings

Second Level Cache

Item Specification

Cache controller Built-in CPU

Cache size 128KB

1st level cache control Always Enabled

Chapter 1 18

Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations.

2nd level cache control Always Enabled

Cache scheme control Fixed-in write back

System Memory

Item Specification

Memory controller Intel 845GL

Onboard memory size 0MB

DIMM socket number 2 Sockets

Supports memory size per socket 512MB

Supports maximum memory size 1024MB

Supports DIMM type DDR-DRAM SODIMM

Supports DIMM Speed 266 MHz

Supports DIMM voltage 3.3 V

Supports DIMM package 200-pin so-DIMM

Memory module combinations You can install memory modules in any combinations as long as they match the above specifications .

Memory Combinations

Slot 1 Slot 2 Total Memory

0MB 128MB 128 MB

128MB 0MB 128 MB

128MB 128MB 256 MB

256MB 0MB 256MB

0MB 256MB 256MB

256MB 128MB 384MB

128MB 256MB 384MB

256MB 256MB 512MB

0MB 512MB 512MB

512MB 128MB 640MB

256MB 512MB 768MB

128MB 512MB 640MB

512MB 256MB 768MB

256MB 128MB 384MB

128MB 256MB 384MB

512MB 512MB 1024MB

0MB 512MB 512MB

Second Level Cache

Item Specification


Modem Interface

Item Specification

Chipset Ambit MDC module with Lucent modem controller

Fax modem data baud rate (bps) 14.4K

Data modem data baud rate (bps) 56K

Supports modem protocol V.90/V.92MDC

Modem connector type RJ11

Modem connector location Rear side

Floppy Disk Drive Interface

Item Specification

Vendor & model name Mitsumi D353G W/I BEZ

MCI JU-226A293

Floppy Disk Specifications

Media recognition 2DD (720KB) 2HD (1.2 MB, 3 mode) 2HD (1.44MB)

Sectors/track 9 15 18

Tracks 80 80 80

Data transfer rate (Kbit/s)

1 MB 1.6 MB 2 MB

Rotational speed (RPM) 300 360 300

Read/write heads 2

Encoding method MFM

Power Requirement

Input Voltage (V) +5V

Hard Disk Drive Interface

Item Specification

Vendor & Model Name IBM (IC25N020ATD)

Capacity (MB) 20000

Bytes per sector 512

Logical heads 16

Logical sectors 63

Drive Format

Logical cylinders 16383

Physical read/write heads 3

Disks 2

Spindle speed (RPM) 4200RPM

Performance Specifications

Buffer size 2MB

Interface ATA-5

Data transfer rate (disk-buffer, Mbytes/s)

121-216

Data transfer, rate (host~buffer, Mbytes/s)

100 MB/Sec

DC Power Requirements

Voltage tolerance 5 +/- 5%

Chapter 1 20

CD-ROM Interface

Items Specification

Vendor & Model Name Mitsumi SR-244W1

Performance Specification

Transfer rate Read Sustained:

1545~3600 KB/sec

Programmed I/O:

16.7 MB/sec Max. (Mode 0~4)

Multi-word DMA:

16.7 MB/sec Max. (Mode 0~2)

Ultra DMA:

33.3MB/sec Max.

Access time (typ.) Random: 115 ms

Full Stroke: 250 ms

Rotation speed 5136 rpm

Data Buffer Capacity 128 KB

Interface IDE

Applicable disc format CD/CD-ROM(12cm,8cm), CD-R, CD-RW, CD-DA, CD-ROM (Mode 1, Mode2), CD-ROM XA (Mode 2, Form1 and Form 2), Photo CD (Single, Multi- session), Enhanced CD

Loading mechanism Drawer with soft eject and emergency eject hole

Power Requirement

Input Voltage +5V[DC]+/-5%

DVD-ROM Interface

Item Specification

Vendor & model name MKE SR-8177-BAA6

Performance Specification With CD Diskette With DVD Diskette

Transfer rate (KB/sec) Average Sustained:

CAV mode

775~1800 blocks/sec

(10.3X to 24X)

1550~3600kBytes/sec (Mode 1)

1768~4106 kBytes/sec (Mode 2)

DVD-5:

Normal Speed (1X) 11.08 Mbits/sec

CAV mode 36.67~88.64 Mbits/sec

DVD-9/DVD-R:

Normal Speed (1X) 11.08 Mbits/sec

CAV mode 36.67~88.64 Mbits/sec


(*1) Average of Data read over the whole area from 00 min. 02 sec. 00 block to 59 min. 58 sec. 74 block more than 2000 times including latency and layered error correction time.(*2) From 00 min. 02 sec. 00 block to 59 min. 58 sec. 74 block including latency and layered error correction time.(*3) Disc: MNSU-005(*4) Average of Data read over the whole area from starting data recorded area (LBA:0) to maximum data recorded area (LBA:23197F), more than 2000 times including latency and layered error correction time.(*5) from starting data recorded area (LBA:0) to maximum data recorded area (LBA:23197F) including latency and layered error correction time.(*6) Disk: MKE-D551.(*7) Average of Data read over the whole area from starting data recorded area (LBA:0) to maximum data recorded area (LBA:3FA0DF), more than 2000 times including latency and layered error correction time.(*8) from starting data recorded area (LBA:0) to maximum data recorded area (LBA:3FA0DF) including latency and layered error correction time.

Average Full Access time (typ.) Random (*1)

CAV mode 110 msec typical 150 msec average max

Full Stroke (*2)

CAV mode 200 msec typical 260 msec average max

DVD-5:

Random (*4) 120 msec typical 160 msec average max

Full Stroke (*5) 270 msec typical 350 msec average max

DVD-9:

Random (*7) 150 msec typical 200 msec average max

Full Stroke (*8) 340 msec typical 450 msec average max

DVD-RAM (2.6G)

Random (*7)

200 msec typical

300 msec average max

Full Stroke (*8)

300 msec typical


DVD-RAM (4.7G)

Random (*9)

180 msec typical


Full Stroke (*10)

320 msec typical


Data Buffer Capacity 512 kBytes

Interface IDE

Applicable disc format DVD: DVD-5, DVD-9, DVD-10, DVD-R (3.95G), DVD-RAM (2.6G), DVD-RAM (4.7G)

CD: CD-Audio, CD-ROM (mode 1 and mode 2), CD-ROM XA (mode 2, form 1 and form 2), CD-I (mode 2, form 1 and form 2), CD-I Ready, CD-I Bridge, CD-WO, CD-RW, Photo CD, Video CD, Enhanced Music CD, CD-TEXT

Loading mechanism Soft eject (with emergency eject hole)

Power Requirement

Input Voltage +5V[DC]+/-5%

DVD-ROM Interface

Item Specification

Chapter 1 22

(*9) Disk: ODSC-PARA

Combo Drive Interface

Item Specification

Vendor & model name KME UJDA740

Performance Specification

Transfer rate (KB/sec) Read Sustained:

DVD-ROM MAX 8X CAV (MAX 10800 KB/sec)

CD-ROM MAX 24X CAV (MAX 3600 KB/sec)

Write:

CD-R 4X, 8X (CLV), Max 16X, MAX 24X (ZCLV)

CD-RW 4X (CLV)

HS-RW 4X,8X, 10X (CLV)

ATAPI Interface:

PIO mode 16.6 MB/sec :PIO Mode 4

DMA mode 16.6 MB/sec:Multi word mode 2

Ultra DMA mode 33.3MB/sec: Ultra DMA mode 2

Buffer rate 2MB

Access time DVD-ROM 180 ms typ. (1/3 stroke)

CD-ROM 130 ms typ. (1/3 stroke)

Start up time less than 15s

Stop time less than 6s

Acoustic noise less than 50 dBA

Interface Enhanced IDE (ATAPI) compatible

Master/Slave Set by Cable Select (By host)

PC compatible PC2001 compatible

Applicable disc format CD:

CD-DA, CD-ROM, CD-ROM XA, CD-R, CD-RW, PhotoCD (multiSession), Video CD, CD-Extra(CD+), CD-text

DVD: DVD-ROM, DVD-R, DVD-RW (Ver.1.1)

Slope 15 degree (Any direction)

Dimensions, Weight 128X129X12.7mm (WXDXH)

(except protrusion)

200g+- 10g

Eject Soft Eject (with emergency eject hole)

Audio Interface

Item Specification

Audio Controller Cirrus Logic CS4299-XQ

Audio onboard or optional Built-in

Mono or Stereo Stereo

Resolution 20 bit stereo Digital to Analog converter

18 bit stereo Analog to Digital converter

Compatibility Microsoft PC98/PC99, AC97 2.1

Mixed sound source Line-in, CD, Video, AUX

Voice channel 8/16 bit, mono/stereo

Sampling rate 44.1 KHz

Internal microphone Yes

Internal speaker / Quantity Yes/2


Supports PnP DMA channel DMA channel 0

DMA channel 1

Supports PnP IRQ IRQ10, IRQ11

Video Interface

Item Specification

Vendor & Model Name Intel 845GL

Chip voltage Core / 2.5V, 1.5V, 1.8V

Supports ZV (Zoomed Video) port NO

Graph interface 4X AGP (Accelerated Graphic Port) Bus

Maximum resolution (LCD) 1024 x768 (32bit colors)

Maximum resolution (CRT) 1024x768 (32 bit colors)

1280x1024 (32 bit colors)

1600x1200 (32 bit colors)

Video Memory

Item Specification

Fixed or upgradeable Fixed, share the system memory

Video memory size 8MB

Video Resolutions Mode

Resolution Refresh Rate

CRT Only LCD/CRT Simultaneous

640x480x256 90 60

640x480x64K 90 60

640x480x16M 90 60

800x600x256 90 60

800x600x64K 90 60

1024x768x256 90 60

Parallel Port

Item Specification

Parallel port controller LPC47N227

Number of parallel port 1

Location Rear side

Connector type 25-pin D-type

Parallel port function control Enable/Disable by BIOS Setup

Supports ECP/EPP Yes (set by BIOS setup)

Optional ECP DMA channel (in BIOS Setup)

DMA channel 1 and 3

Optional parallel port I/O address (in BIOS Setup)

378, 278, 3BC

Optional parallel port IRQ (in BIOS Setup)

IRQ7, IRQ5

Audio Interface

Item Specification

Chapter 1 24

USB Port

Item Specification

USB Compliancy Level 2.0

OHCI USB 2.0

Number of USB port 2

Location Rear side

Serial port function control Enable/Disable by BIOS Setup

PCMCIA Port

Item Specification

PCMCIA controller O2-Micro Cardbus Controller OZ6912T-U

Supports card type Type III

Number of slots One type III

Access location Left side

Supports ZV (Zoomed Video) port Yes

Supports 32 bit CardBus Yes (IRQ17)

Keyboard

Item Specification

Keyboard controller Mitsubishi M38857

Keyboard vendor & model name API

Total number of keypads 84-/85/88- key

Windows 95 keys Yes

Internal & external keyboard work simultaneously Yes

Battery

Item Specification

Vendor & model name SIMPLO

Battery Type Li-ION

Pack capacity 2000mAH

Cell voltage 3.8V / 1.2V

Number of battery cell 8

Package configuration 4529 / 8S

Package voltage 14.8V

DC-DC/Charger Converter

Item Specification

Vendor & Model Name O2

Input Voltage AC Adapter or Battery: 8V - 19VDC

DC-DC Converter Output

Output Rating +5V 3.3V 12V

Current (w/load, A) 0~5A 0~4A 120mA

Charger Output Li-ION Ni-MH


NOTE: DC-AC inverter is used to generate very high AC voltage, then support to LCD CCFT backlight user, and is also responsible for the control of LCD brightness. Avoid touching the DC-AC inverter area while the system unit is turned on.

NOTE: There is an EEPROM in the inverter, which stores its supported LCD type and ID code. If you replace a new inverter or replace the LCD with a different brand, use Inverter ID utility to update the ID information.

.

Normal charge (charge while system is not operative)

2.8A 2.25V

Background charge (charge even system is still operative)

0.8A

Battery-low 2 level (V) 12.5V 8V

Battery-low 3 level (V) 10V 7.5V

Protection

Charger protection Over Current Protection

DC/DC converter protection OCP (Over Current Protection, A)

OVP (Over Voltage Protection, V)

UVP (Under Voltage Protection, V)

DC-AC LCD Inverter

Item Specification

Vendor & model name Ambit

Input voltage (V) 8 ~ 21V

Input current (mA) 1A (max.)

Output voltage(Vrms, no load)

1400Vrms

Output voltagefrequency (kHz)

40 ~ 70KHz

Output Current/Lamp 5.5 mA ~ 6.5mA

LCD

Item Specification

Vendor & model name 14.1” AU

B141XN04 V2

15” Hitachi

TX38D85VC1CAB

Mechanical Specifications

LCD display area (diagonal, inch) 14.1 15

Display technology TFT TFT

Resolution XGA (1024x768) XGA (1024x768)

Support colors 262K 262K

Optical Specification

Brightness control Keyboard hotkey Keyboard hotkey

Contrast control None None

Electrical Specification

Supply voltage for LCD display (V) 3.3 (typ.) 3.3 (typ.)

Supply voltage for LCD backlight (Vrms) 650 (typ.) 650 (typ.)

DC-DC/Charger Converter

Item Specification

Chapter 1 26

AC Adapter

Item Specification

Vendor & model name Delta ADP-65DB

Input Requirements

Maximum input current (A, @90Vac, full load)

1.5 A @ 110Vac

1.0 A @ 240Vac

Nominal frequency (Hz) 50-60

Frequency variation range (Hz) 47-63

Input voltage range (Vrms) 90-270

Inrush current The maximum inrush current will be less than 50A and 100A when the adapter is connected to 115Vac and 230Vac respectively.

Efficiency It should provide an efficiency of 80% minimum, when measured at maximum load under 115Vac.

Output Ratings (CV mode)

DC output voltage 19V

Noise + Ripple 300mVp-pmax (20 MHz bandwidth)

Load 0(min) 3.16A(max)

Output Ratings (CC mode)

DC output voltage 19V +/-1.0V for CV mode

Constant current mode 3.6 +/- 0.3A

Dynamic Output Characteristics

Turn-on delay time 3 sec (@ 115Vac)

Hold up time 5ms (@115Vac, Full load)

Over Voltage Protection (OVP) 24V

Short circuit protection 3.9A max can be protected and output can be shorted without damage

Electrostatic discharge (ESD) 15KV (at air discharge)

8KV (at contact discharge)

Dielectric Withstand Voltage

Primary to secondary 3000Vac

Leakage current 0.25 mA max. (@ 254Vac, 60Hz)

Regulatory Requirements Safety Requirements:

1.The subject product rated 100-120V 60Hz must be listed under UL 1950 and certified with SCA Standard C22.2 No.950.

2.The subject product rated 200-240V 50Hz must comply with low voltage directive 73/23EEC.

EMI Requirements:

1.The subject product rated 100-120V 60Hz must meet the EMI requirements of FCC part 15, Subpart B for Class B Digital Device and get FCC Certification before marketing into USA and Canada.

2.The subject product rated 200-240V 50Hz must meet the EMC Directive 89/336/EEC.

3.The subject product rated 100-120V must meet the VCCI-2 EMI requirements.


Power Management

Power Saving Mode Phenomenon

Standby Mode

Enter Standby Mode when

1.Standby/Hibernation hot-key is pressed and system is not ready to enter Hibernation mode.

2.System standby/ Hibernation timer expires and system is not ready to enter Hibernation mode.

� The buzzer beeps� The Sleep indicator lights up

Hibernation Mode

Enter Hibernation Mode (suspend to HDD) when

1.Hibernation hot-key is pressed and system is ready to enter Hibernation mode

2.System Hibernation timer expires and system is ready to enter Hibernation mode.

� All power shuts off

Display Standby Mode

Keyboard, built-in touchpad, and an external PS/2 pointing device are idle for a specified period.

� The display shuts off

Hard Disk Standby Mode

Hard disk is idle within a specified period of time.

� Hard disk drive is in standby mode.(spindle turned-off)

Environmental Requirements

Item Specification

Temperature

Operating +5~+35 °C

Non-operating -20~+60 °C

Humidity

Operating 20% to 85% RH, non-condensing

Non-operating 20% to 85% RH, non-condensing (Unpacked)

Non-operating 20% to 90% RH, non-condensing (Storage package)

Vibration

Operating (unpacked) 5~25.6Hz: 0.38mm (peak to peak)

25.6~250Hz: 0.5G

Non-operating (unpacked) 5~27.1Hz: 0.6G

27.1~50Hz: 0.04mm (peak to peak)

50~500Hz: 2.0G

Non-operating (packed) 5~62.6Hz: 0.51mm (peak to peak)

62.6~500Hz: 4.0G

Mechanical Specification

Item Specification

Dimensions 326(W) x 267.5(D) x 35.0~37.3(H)mm

Weight 6.8 Ibs with14.1” TFT LCD and CD-ROM/ 6.9 Ibs with 15”LCD and CD-ROM

Chapter 1 28

I/O Ports One type III PCMCIA (PC Card) port, one RJ-11 port, one RJ-45 port, one DC-in port, one ECP parallel port, four USB ports (two optional), two IEEE 1394 ports (optional)one line-in jack, one line-out jack, one speaker/headphone-out jack, one

VGA port /I2 C compatible (optional).

Drive Bays One

Material Plastic

Indicators Power-on, Standby, Battery Status, Media Access, CapsLock and NumLock

Switch Power

Memory Address Map

Memory Address Size Function

00000000-0009FFFF 640 KB Base memory

80600000-80600FFF

80620000-8063FFFF

81000000-81FFFFF

000A0000-000CFFFF

4 KB Intel 845GL

128 KB

3 MB

192 KB

08000000-08000FFF

08001000-08001FFF

4 KB O2 Micro OZ6912T Cardbus Controller

4 KB

82400000-82400FFF 4 KB USB

82200000-82200FFF 4 KB Audio

I/O Address Map

I/O Address Function

00000000-0000000F Direct Memory Access controller

00000000-00000CF7 PCI bus

00000010-0000001F Motherboard resources

00000020-00000021 Programmable interrupt controller

00000024-00000025 Motherboard resources


0000002C-0000002D Motherboard resources

0000002E-0000002F Motherboard resources




0000003C-0000003D Motherboard resources

00000040-00000043 System Timer


00000060-00000060 Standard 101/102-key or Microsoft Natural PS/2 keyboard

00000061-00000061 System Speaker

00000062-00000062 Microsoft ACPI-Compliant Embedded Controller

00000064-00000064 Standard 101/102-key or Microsoft Natural PS/2 keyboard

00000066-00000066 Microsoft ACPI-Compliant Embedded Controller

00000070-00000071 System CMOS/realtime clock



Mechanical Specification

Item Specification


00000081-0000008F Direct memory access controller


000000A0-000000A1 Programmable interrupt controller

000000A4-000000A5 Motherboard resources

000000A8-000000A9 Motherboard resources

000000AC-000000AD Motherboard resources

000000B0-000000B5 Motherboard resources

000000B8-000000B9 Motherboard resources

000000BC-000000BD Motherboard resources

000000C0-000000DF Direct memory access controller

000000F0-000000FE Numeric data processor

00000170-00000177 Secondary IDE channel

000001C0-000001CF Motherboard resources

000001F0-000001F7 Primary IDE channel

00000274-00000277 ISAPNP Read Data Report

00000279-00000279 ISAPNP Read Data Report

00000376-00000376 Secondary IDE channel

00000378-0000037F Printer (LPT1)

000003B0-000003BB Intel (R) 82845G Graphic Controller

000003C0-000003DF Intel (R) 82845G Graphic Controller

000003F0-000003F5 Standard floppy disk controller

000003F6-000003F6 Primary IDE channel

000003F7-000003F7 Standard floppy disk controller

000003F8-000003FF Motherboard resources

000004D0-000004D1 Motherboard resources


00000A79-00000A79 ISAPNP Read Data Report

00000D00-0000FFFF PCI bus


00001180-000011BF Motherboard resources

00001800-0000181F Intel (R) 82801DB/DBM USB Universal Host Controller-24C2



00001860-0000186F Intel (R) 82801DB Ultra ATA Storage Controller-24CB

00001880-0000189F Intel (R) 82801DB/DBM SMBus Controller-24C3

000018C0-000018FF Crystal WDM AC’97 Driver for ICH4

00001C00-00001CFF Crystal WDM AC’97 Driver for ICH4

00002000-0000207F Agere Systems AC’97 Modem

00002400-000024FF Agere Systems AC’97 Modem

00003000-000030FF Realtek RTL8139/810x Family Fast Ethernet NIC

0000FD00-0000FDFF O2Micro OZ6912 CardBus Controller

0000FE00-0000FE00 Motherboard Resources

0000FF00-0000FFFF O2Micro OZ6912 CardBus Controller

I/O Address Map

I/O Address Function

Chapter 1 30

NOTE: IRQ settings may be changed by OS

IRQ Assignment Map

Interrupt Channel Function

NMI System errors

IRQ0 System timer

IRQ1 Keyboard

IRQ6 Floppy

IRQ8 Real time clock

IRQ9 Microsoft ACPI-Compliant System

IRQ11 Intel (R) 82801DB/DBM SMBus Controller-24C2

IRQ12 Synaptics PS2 pointing device

IRQ13 Numeric data processor

IRQ14 1st IDE device

IRQ15 2nd IDE device

IRQ16 Intel (R) 82801DB/DBM USB Universal Host Controller-24C2

IRQ16 Intel (R) 845G Graphics Controller

IRQ17 Agere Systems AC’97 Modem

IRQ17 Crystal WDM AC’97 Driver for ICH4

IRQ17 O2Micro OZ6912 CardBus Controller



IRQ19 Realtek RTL8139/810x Family Fast Ethernet NIC

IRQ21 OHCI Compliant IEEE 1394 Host Controller

IRQ23 Intel (R) 82801DB/DBM USB 2.0 Enhanced Host Controller-24CD

DMA Channel Assignment

DMA Channel Function

DRQ0 Not used

DRQ1 Not used

DRQ2 Floppy

DRQ3 Not used

DRQ4 DMA controller

DRQ5 Not used

DRQ6 Not used

DRQ7 Not used


Chapter 1 32

System Utilities

Chapter 2

BIOS Setup UtilityThe BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System).

Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.

To activate the BIOS Utility, press m during POST (while the TravelMate logo is being displayed).

PhoenixBIOS Setup Utility

Information Main Advanced Security Boot Exit

CPU TypeSystem MemoryExtended MemoryHDD1 Serial NumberSystem BIOS VersionVGA BIOS VersionKBC Version:Serial NumberAsset Tag NumberProduct NameManufacture NameUUID Number

Mobile Intel (R) Celeron (R) CPU 1.60GHz640 KB121344 KB115188V0.51 (BXB35WW)275902.29.258146W01008246015BFM000No Asset TagTravelMate 230Acer5f8f5060-fd71-11d6-85f3-c5c61adec588

F1 Help �� Select Item F5/F6 Change Values F9 Setup DefaultsEsc Exit �� Select Menu Enter Select > Sub-Menu F10 Save and Exit

PhoenixBIOS Setup UtilityPhoenixBIOS Setup Utility

Information Main Advanced Security Boot ExitInformation Main Advanced Security Boot Exit






F1 Help �� Select Item F5/F6 Change Values F9 Setup DefaultsEsc Exit �� Select Menu Enter Select > Sub-Menu F10 Save and ExitF1 Help �� Select Item F5/F6 Change Values F9 Setup DefaultsEsc Exit �� Select Menu Enter Select > Sub-Menu F10 Save and Exit

Chapter 2 33




Pentium (R) IV 1.4GHz640 KB121344 KB115188V0.51 (BXB35WW)275902.29.258146W01008246015BFM000No Asset TagTravelMate 280Acer5f8f5060-fd71-11d6-85f3-c5c61adec588











Multi-Boot MenuUsers can press F12 during POST to enter the Multi Boot Selection Menu. In this menu users can change boot device without entering BIOS SETUP utility.

NOTE: If users disable the multi boot selection menu in BIOS SETUP utility, the message “ Press F12 to enter the multi boot selection menu” will not appear during POST.

NOTE: If users disable the “Boot on LAN” option in BIOS SETUP utility, then the option of Realtek PXE2.0 Boot Agent will not appear.

Navigating the BIOS UtilityThere are six menu options: System Information, Basic System Settings, Startup Configuration, Onboard Device Configuration, System Security and Loading Default Settings.

To enter a menu, highlight the item using the w / y keys, then press e.

Within a menu, navigate through the BIOS Utility by following these instructions:

� Press the w / y keys to move between the parameters.

� Press the p / qkeys to change the value of a parameter.

� Press the | key while you are in any of the menu options to return to the main menu.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys are shown at the bottom of the screen.

Boot Menu

1. +Removable Devices2. CD-ROM drive3. +Hard Drive4. D2D Recovery

<Enter Setup>

Boot MenuBoot Menu


<Enter Setup>


<Enter Setup>

Chapter 2 35

System InformationThe System Information screen displays a summary of your computer hardware information.















NOTE: The screen above is a sample and may not reflect the actual data on your computer. “X” may refer to a series of numbers and/or characters.

The following table describes the information in this screen.

The items in this screen are important and vital information about your computer. If you experience computer problems and need to contact technical support, this data helps our service personnel know more about your computer.

Parameter Description

CPU Type Describe the type of CPU installed in the system.

System Memory Display the current system memory.

Extended Memory Display the current extended memory.

HDD Serial Number Display the primary master HDD serial number. If there is no primary master HDD, then show “None”.

System BIOS Version Show the current system BIOS version.

VGA BIOS Version Show the video graphics accelerator BIOS version. It is obtained from VGA BIOS AX=5F01.

KBC Version Display the current KBC version.

Serial Number Show the serial number of the computer. (32 characters)

Asset Tag Number Show the asset tag number of the computer. (16 characters)

Product Name Show the official name of the product. (15 characters)

Manufacturer Name Show the manufacturer of the computer. (15 characters)

UUID Show the universally unique identifier of your computer. (16 Byte-Hex-Digital)














Chapter 2 37

Main System SettingsThe Basic System Settings screen allows you to set the system date and time.

The following table describes the parameters in this screen.

Parameter Description Format

System Time Sets the system time. HH:MM:SS (hour:minute:second)

System Date Sets the system date. DDD MMM DD, YYYY (day-of-the-week month day, year)

Boot Display Sets the display device on boot up.

When set to Auto, the computer automatically determines the display device. If an external display device (e.g., monitor) is connected, it becomes the boot display. When set to Both, the computer outputs to both the computer display screen and an external display device if one is connected.

Auto or Both

Quick Boot Mode Allow the system to skip certain tests while booting. This will decrease the time needed to boot the system.

Enabled or Disabled

Boot-time Diagnostic Screen

Boot-time diagnostic during boot.

Help: Enable to show the BIOS logo picture screen on boot up.

Disabled or Enabled



System Time: System Date:

Boot Display

QuickBoot ModeBoot-time Diagnostic Screen:

Boot on LANHotkey Beep

Auto DimF12 Multi-Boot

[08:46:55][12/03/2002]

[Auto]

[Enabled][Disabled]

[Disabled][Enabled]

[Enabled][Enabled]

Item Specific Help

<Tab>, <Shift-Tab>, or<Enter> selects field.





Boot Display





Boot Display




[08:46:55][12/03/2002]

[Auto]

[Enabled][Disabled]

[Disabled][Enabled]

[Enabled][Enabled]

[08:46:55][12/03/2002]

[Auto]

[Enabled][Disabled]

[Disabled][Enabled]

[Enabled][Enabled]

Item Specific HelpItem Specific Help

<Tab>, <Shift-Tab>, or<Enter> selects field.<Tab>, <Shift-Tab>, or<Enter> selects field.



Setting the Boot Drive Sequence

The Boot Drive Sequence section lists boot priorities (1st, 2nd, 3rd, and 4th) for bootable drives in your computer.

For example, the default value (1st:Floppy Disk, 2nd:Hard Disk, and 3rd: CD-ROM, 4th: Realtek PXE2.0 Boot Agent) tells the computer to first search for a bootable floppy disk in the floppy drive. If it finds one present, it boots up from that floppy disk. If not, the computer continues to search for a bootable CD-ROM in the CD-ROM drive. If it cannot boot up from the CD-ROM drive, it continues by booting up from the hard disk and etc...

To set the boot drive sequence, use the w / y keys to select a priority level (1st, 2nd, 3rd, and 4th), then use

the z / x keys to select the device for that priority level.

NOTE: When Boot on LAN is set Enabled, then the 4th option: Realtek PXE2.0 Boot Agent shows in the list.

Boot on LAN When it is enabled, a remote host with an appropriate boot image can boot this computer via the internal LAN.

Disabled or Enabled

Hotkey Beep Help: Enable or disable hotkey beep.

Enabled or Disabled

Auto Dim Help: The system will support an automatic dimming of the

LCD backlight when the AC power is NOT available (running on battery power).

Options: Enabled or Disabled

Help: Users could choose if to display ‘Fn-F12 for multi-

boot’ message during post

Enabled or Disabled

F12 Multi-Boot When “Fn-F12” is pressed, a multi-boot message will be displayed during POST.

Enabled or Disabled

Parameter Description Format

Chapter 2 39

Advanced InformationThe Advanced Information screen contains parameter values that define how your computer behaves on system startup.

The following table describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.



Legacy Diskette A:

>Primary Master >Secondary Master

>I/O Device Configuration>PCI IRQ Routing

Legacy USB Support:System Boot From Hard Disk RecoveryScreen ExpansionIGD-Memory typeBattery Mode Performance

[1.44/1.25MB 3 ½”

[20004MB][CD-ROM]

[Enabled][Enable][Enabled][UMA=1MB][Max Batt]

Item Specific Help

Selects floppy type. Note that 1.25MB 3 ½” references a 1024 byte/ sector Japanese media format. The 1.25MB 3 ½” diskette requires a 3-mode floppy-disk drive.




Legacy Diskette A:




Legacy Diskette A:




[1.44/1.25MB 3 ½”

[20004MB][CD-ROM]


[1.44/1.25MB 3 ½”

[20004MB][CD-ROM]


[1.44/1.25MB 3 ½”

[20004MB][CD-ROM]







Parameter Description Options

Legacy Diskette A Help: Selects floppy type. Note that 1.25MB 3 1/2” references a 1024 byte/sector Japanese media format. The 1.25MB, 3 1/2” diskette requires a 3-Mode floppy-disk drive.

Enable or Disable Legacy Diskette A

1.44/1.25MB 3 1/2” or Disabled

Primary Master Show IDE Primary Master HDD size.

User can enter submenu to set some detail functions

Auto or User or CD-ROM or ATAPI Removable

Secondary Master Show IDE Secondary Master Device Status.

User can enter submenu to set some detail functions.

Auto or User or CD-ROM or ATAPI Removable

I/O Device Configuration Enter submenu to set onboard device configuration

Help: Peripheral Configuration.

PCI IRQ Routing Set Default IRQ of PCI device.

Help: Menu used to set IRQ for PCI Devices.

Auto/ User Select

Legacy USB Support Enabled: Enable support for Legacy Universal Serial Bus.

Enabled or Disabled

System Boot from Hard Disk Recovery

Enable D2D function. Enable or Disable

Screen Expansion Help: Options: Enabled or Disabled Enabled or Disabled

IGD-Memory Type Select the amount of the main memory that the Internal Graphics Device will use. Let UMA= the amount of pre-allocated memory made available.

UMA 1MB or UMA8MB

Battery Mode Performance This item allows you to select the performance while battery mode.

Max Batt or Maximum Performance

Chapter 2 41

Primary MasterThe Primary Master sub-menu contains parameters related to the primary hard disk.

CAUTION: The parameters in this screen are for the advanced users only. Typically, you do not need to change the values in this screen.The default setting of Auto optimizes all the settings for your hard disk.


Type The setting of detail functions stands on type.

Help: Auto= Autotype Hard-Disk drive installed here.

Auto/CD-ROM/ ATAPI Removable/User


Advanced

Primary Master [10056MB] Item Specific Help

Type: [Auto]

LBA FormatTotal Sectors: 39070080Maximum Capacity: 20004MB

Multi-Sector Transfers: [16 Sectors]LBA Mode Control: [Enabled]32 Bit I/O: [Disabled]Transfer Mode: [Fast PIO 4]Ultra DMA Mode: [Disabled]

User= you enter parameters of hard-disk drive installed at this connection.Auto: autotypes hard-disk drive installed here.CD-ROM= a CD-ROM drive is installed here.ATAPI Removable= removable disk drive is installed here.



Advanced


Advanced


Advanced

Primary Master [10056MB]Primary Master [10056MB] Item Specific HelpItem Specific Help

Type: [Auto]



Type: [Auto]







Secondary MasterThe Secondary Master sub-menu contains parameters related to the Media bay drive.

CAUTION: The parameters in this screen are for the advanced users only. Typically, you do not need to change the values in this screen. The default setting of Auto optimizes all the settings for your Media bay drive.


Type The setting of detail functions stands on type.

Help: Auto= Autotype Hard-Disk drive installed here

Auto/ CD-ROM/ ATAPI Removable/ User


Advanced

Secondary Master [20004MB] Item Specific Help

Type: [Auto]






Advanced


Advanced


Advanced

Secondary Master [20004MB]Secondary Master [20004MB] Item Specific HelpItem Specific Help

Type: [Auto]



Type: [Auto]






Chapter 2 43

I/O Device ConfigurationThe parameters in this screen are for advanced users only. You do not need to change the values in this screen because these values are already optimized.

The I/O Device Configuration screen assigns resources to basic computer communication hardware.


NOTE: When the device is disabled, all the sub-items will be hidden.


Parallel Port Enables or disable the parallel port.

The parallel port is a PnP device. Enabled/Disabled setting won’t affect the Windows Device Manager setting of the parallel port.

Help: [Enable]: User configuration

[Disable]: No configuration

Mode: Sets operation mode of the parallel port.

Only set the parallel post operation mode in BIOS setup. If set to be ECP mode, the Windows will assume the parallel port as the ECP port.

Base I/O address: If operation mode is set to Base I/O address, sets the base I/O address of the parallel port.

Interrupt: If operation mode is set to interrupt, sets the interrupt request of the parallel port.

Enabled or Disabled

Bi-directional, Output only, EPP, ECP

378, 3BC, 278

IRQ7, IQ5

Phoen ixB IO S Setu p U tility

Ad vanced

I/O D ev ice C onfiguration Item Specif ic H elp

Para lle l Port: [E nabled]M ode: [B i-d irection]Base I/O address: [378]In terrupt: [IR Q 7]

C onfigure para lle l portU sing options:

[D isab led]N o configuration

[Enabled]U ser C onfiguration

[Auto]B IO S or O S choosesconfiguration

(O S C ontro lled)D isp layed w hen C ontro lled by O S

F1 H elp �� Selec t Item F5/F6 C hange V alues F9 Setup D efau ltsEsc Ex it �� Select M enu En ter Select > Sub-M enu F10 Save and Ex it


Ad vanced


Ad vanced


Ad vanced

I/O D ev ice C onfigurationI/O D ev ice C onfiguration Item Specif ic H elpItem Specif ic H elp













F1 H elp �� Selec t Item F5/F6 C hange V alues F9 Setup D efau ltsEsc Ex it �� Select M enu En ter Select > Sub-M enu F10 Save and Ex itF1 H elp �� Selec t Item F5/F6 C hange V alues F9 Setup D efau ltsEsc Ex it �� Select M enu En ter Select > Sub-M enu F10 Save and Ex it


PCI IRQ RoutingThe PCI IRQ Routing sub-menu allows you to set IRQ for PCI devices.

CAUTION: The parameters in this screen are for advanced users only. Typically, you do not need to change the values in this screen because these values are already optimized.


PIRQ A-H# Set default IRQ of PCI device.

Help: PCI devices can use hardware interrupt called IRQs. A PCI device cannot use IRQs already in use by ISA or EISA devices. Use “Auto” only if no ISA or EISA legacy cards are installed.

IRQ 10 or IRQ11, Disabled, Auto Select, IRQ3, IRQ7


Advanced

PCI IRQ Routing Item Specific Help

PIRQ A# :[11]PIRQ B# :[10]PIRQ C# :[11]PIRQ D# :[10]PIRQ E# :[11]PIRQ F# :[10]PIRQ G# :[11]PIRQ H# :[10]

PCI devices can use hardware interrupts called IRQs. A PCI device cannot use IRQs already in use by ISA or EISA devices. Use ‘Auto’ only if no ISA or Eisa legacy cards are installed.



Advanced


Advanced


Advanced

PCI IRQ RoutingPCI IRQ Routing Item Specific HelpItem Specific Help






Chapter 2 45

System SecurityThe System Security screen contains parameters that help safeguard and protect your computer from unauthorized use.


Setting a Password

Follow these steps:

1. Use the cursor w/y keys to highlight a Password parameter (Supervisor Password, User Password, Password on boot or Primary Hard Disk Password) and press thee key. The password box appears as below if choosing Set Supervisor Password:


Set Supervisor Password While entering SETUP, BIOS need to request user to enter supervisor password if set.

This password protects the BIOS SETUP menu from unauthorized entry.

Enter

Set User Password During POST, BIOS needs to check user password if set.

This password protects the system from unauthorized user entry before OS boots up.

Enter

Password on Boot During POST, BIOS need to check power on password if set.

This password protects the computer from unauthorized entry during boot-up.

Enabled or Disabled

Set Primary Hard Disk Password

During POST, BIOS need to check Hard disk password if set.

This password protects the computer from unauthorized entry during boot-up if a second Hard disk is inserted.

Enter



Set Supervisor Password [Enter]Set User Password [Enter]

Password on boot [Enabled]

Set Primary Hard Disk Password [Enter]

Item Specific Help

Supervisor password controls the access of the whole setup utility.















2. Type a password. The password may consist of up to eight characters (A-Z, a-z, 0-9) and then press e.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.

3. Retype password to verify your first entry and then press e. The following screen appears:

4. After setting the password, the computer automatically sets the chosen password parameter to Present.

5. Press ̂to return to the main menu.

6. Press u. The following dialogue box appears.

7. Select Yes and press e to save the password and exit the BIOS utility.

Four password types protect your computer from unauthorized access. Setting these passwords creates several different levels of protection for your computer and data:

� Supervisor Password prevents unauthorized entry to the BIOS Utility. Once set, you must key-in this password to gain access to the BIOS Utility.

� User Password and Password On Boot secure your computer against unauthorized use. Combine the use of this password with password checkpoints on boot-up and resume from hibernation for maximum security.

� Hard Disk Password protects your data by preventing unauthorized access to your hard disk. Even if the hard disk is removed from the computer and moved to another computer, it cannot be accessed without the Hard Disk Password.

When a password is set, a password prompt appears on the left-hand corner of the display screen.

1. When the Supervisor Password is set, the following prompt appears when you press m to enter the BIOS Utility at boot-up.

Set Supervisor Password

Enter N ew Password [ ]C onfirm N ew Password [ ]

Set Supervisor Password

Enter N ew Password [ ]C onfirm N ew Password [ ]

Setup Notice

C hanges have been saved.[Continue]

Setup Notice

C hanges have been saved.[Continue]

Setup Confirmation

Save Configuration changes and exit now?

[Yes] [No]

Setup Confirmation

Save Configuration changes and exit now?

[Yes] [No]

Enter Password

Chapter 2 47

Type the Supervisor Password and press e to access the BIOS Utility.

2. When the User Password is set and Power on boot is set enabled, the following prompt appears at boot-up when pressing m.

Type the User Password (a symbol appears for each character you type) and press e to use the computer.

If you enter the password incorrectly, an x symbol appears. Try again and press e.

3. When the Power on boot is set enabled, the following prompt appears at boot-up.

4. When the Hard Disk Password is set, the following prompt appears at boot-up.

Type the Hard Disk Password (a symbol appears for each character you type) and press e to use the

computer. If you enter the password incorrectly, an x symbol appears. Try again and press e.

You have three chances to enter a password. If you successfully entered the password, the system starts Windows.

Removing a Password

If you fail to enter the password correctly after three tries, the system hangs.

To change a password, follow the same steps used to set a password.

1. Use the cursor w/y keys to highlight a Password parameter (Supervisor Password, User Password, Password on boot) and press e. The following prompt appears:

2. Type Current Password, leave the “ Enter New Password” blank and press e. Leave “ Confirm New Password” blank and press e, then the password is removed.

Enter Password

Enter Password

Enter Password

Enter Current Password [ ]Enter New Password [ ]Confirm New Password [ ]


Boot OptionsUsers can press F12 during POST to enter the Boot Options Menu. In this menu users can change boot device without entering BIOS SETUP utility.

NOTE: There are three priorities that can let the user to specify the boot device sequence.

The priority of options from top to bottom is 1st, 2nd, 3rd ,and 4th.

If the Removable Device or Hard Drive option has multi devices, show ‘+’ in front of option and show each device information.

Help: Keys used to view or configure devices:

<e> expands or collapses devices with a + or -

<p>and <q> moves the device up and or down.



+Removable Devices+Hard DriveCD-ROM DriveD2D Recovery

Item Specific Help

Keys used to view or configure devices:<Enter> expands orcollapses devices

<F5> and <F6> moves thedevice up or down.












Chapter 2 49

Exit SetupThis menu contains exit options.

The following table describes the parameters in this screen. Setting in boldface are the defaults and suggested parameter settings.

Load Setup Default

If you want to restore all parameter settings to their default values, select this menu item and press e. The following dialog box displays.

Parameter Description

Exit Saving Changes Save any changes, and exit BIOS setup.

Help: Exit System Setup and save your changes to CMOS.

Exit Discarding Changes Discard any changes, and exit BIOS setup.

Help: Exit utility without saving Setup data to CMOS.

Load Setup Defaults Load Setup Defaults.

Help: Load default values for all SETUP items.

Discard Changes Discard any changes.

Help: Load previous value from CMOS for all SETUP items.

Save Changes Save changes.

Help: Save Setup data to CMOS.



Exit Saving ChangesExit Discarding ChangesLoad Setup DefaultsDiscard ChangesSave Changes

Item Specific Help

Exit System Setup and save your changes to CMOS.





Item Specific Help

Exit System Setup and save your changes to CMOS.







Exit System Setup and save your changes to CMOS.Exit System Setup and save your changes to CMOS.



If you would like to load factory- default settings for all parameters, use the cursor z / x keys to select Yes;

then press e. Choose No if otherwise.

Do you want to load default settings?[Yes] [No]

Chapter 2 51

BIOS Flash UtilityThe BIOS flash memory update is required for the following conditions:

� New versions of system programs

� New features or options

Use the WFlash utility to update the system BIOS flash ROM.

Executing the Flash ProgramPlease do the following to update BIOS.

To update BIOS:

1. Prepare the BIOS Flash Diskette

a. Prepare the BIOS Flash Package.

2. Unzip this package

3. Run Update.bat

4. The system will ask you to reboot the computer after the BIOS is updated.


System Utility DisketteThis utility diskette is for the TravelMate 230/ 280 notebook machine. You can find the utility in Service CD kit. It provides the following functions:

1. Panel ID Utility

2. 1394 GUID Utility

3. Mother Board Data Utility

To use this diskette, first boot from this diskette, then a “Microsoft Windows ME Startup Menu” prompt you to choose the testing item. Follow the instructions on screen to proceed.

NOTE: This program contains a readme.txt file. This readme.txt file will introduce each test utility and its functions.

Chapter 2 53

System Diagnostic Diskette

IMPORTANT: 1The diagnostics program here that we used is called PQA (Product Quality Assurance) and is provided by Headquarters. You can utilize it as a basic diagnostic tool. To get this program, you can find it in the service CD kit. To better fit local service requirements, your regional office MAY have other diagnostic program. Please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

NOTE: This program contains a readme.txt file. This readme.txt file will introduce each test and its functions.

1 New added description. Please pay attention to it.


Running PQA Diagnostics ProgramTo run the program, simply type: PQA and press e. The main menu appears on screen.

Press z / xto move around the main menu. Press e to enable the selected option. The main options are Diag, Result, SysInfo, Option and Exit.

The Diag option lets you select testing items and times.

The following screen appears when you select Diag from the main menu.

One Test performs a single test and Manual checks the selected test items in sequence.

Multi Test performs multiple tests of the selected items and check the selected test items in sequence.

Full Test performs all test items in detail for your system.

Quick Test performs all test items quickly for your system.

PQA Vx_x xx-xx-xx

Diag Result SysInfo Option Exit

PQA Vx_x xx-xx-xx

Diag Result SysInfo Option ExitDiag

ONE TESTMULTI TESTFULL TESTQUICK TEST

Chapter 2 55

The screen below appears if you select Multi Test.

Specify the desired number of tests and press e.

After you specify the number of tests to perform, the screen shows a list of test items (see below).

Move the highlight bar wand y from one item to another. Press k to enable or disable the item. The

triangle mark indicates that there are available sub-options. Press e to view the available options of each

selected item. Press | to close the submenu.

The right corner screen information gives you the available function keys and the specified test number.

� k: Enables/disables the item

� ^: Exits the program

� l : Help

� m: Tests the selected item(s)

� e: Opens the available options

� Test Times: Indicates the number of tests to perform.

NOTE: The l and m keys function only after you finish configuring the Test option.

NOTE: When any errors are detected by diagnostic program, refer to “Index of PQA Diagnostic Error Code” for troubleshooting.

PQA Vx_x xx-xx-xx


One TESTMulti TEST

PQA Vx_x xx-xx-xx

Diag Result SysInfo Option Exit

DiagONE TESTMULTI TESTFULL TESTQUICK TEST

TEST COUNT VALUE (1...9999) 1

PQA Vx_x xx-xx-xx


MANUAL TESTAUTO TEST

Test Items[ ] System Board[ ] Memory [ ] Keyboard[ ] Video[ ] Parallel Port[ ] Serial Port[ ] Diskette Drive[ ] Hard Disk[ ] CD-ROM[ ] Coprocessor[ ] Pointing Dev.[ ] Cache

SPACE: mark/unmark selecting itemESC : return to upper menu

F2 : test the marked item(s)ENTER: open sub-item’s menuTest Times = 1

F1 : Help menu


Chapter 3

Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.

To disassemble the computer, you need the following tools:

� Wrist grounding strap and conductive mat for preventing electrostatic discharge

� Number 1 Flat-bladed screwdriver

� Phillips screwdriver

� Tweezers

� Plastic Flat-bladed screwdriver

� Number 5 Hexed screwdriver

NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.

Chapter 3 57

General Information

Before You BeginBefore proceeding with the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug the AC adapter and all power and signal cables from the system.


Disassembly Procedure FlowchartThe flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Battery

START

Middle CoverW/ Launch

Board

Main Board

PCMCIA SlotI/O Port Plate

CD-ROM Drive

CD-ROMDrive Bracket

Touch Pad Frame

Ax2

Keyboard

Jx1

Dx2

Mx1

Jx2

Nx2

CD-ROM Module

Ax2

L1x2L2X2

Ix2

Antennas(Optional)

Ax9

Ex1

Ex3

Ex4

Fx4

Ex3

Launch Board

Dx2

CPU Heat Sink

CPU

Cx2

Heat Plate

Modem Cover

Touch PadBoard

Touch PadButton

Speakers

FDD Module

Modem BoardDIMM

DIMM Cover

Bx2

LCD Module(See Next Page)

HDD Dummy Cover

HDD HDD Bracket

Ax1

Kx2

HDD Module

Ax2

Touch PadScroll Key

Touch PadFPC

Upper Case

Audio Board

PCMCIA Plate

Fan Module

Charger Plate

Wireless LAN Board (Optional)

RTC Battery

Battery

START

Middle CoverW/ Launch

Board

Main Board

PCMCIA SlotI/O Port Plate

CD-ROM Drive

CD-ROMDrive Bracket

Touch Pad Frame

Ax2

Keyboard

Jx1

Dx2

Mx1

Jx2

Nx2

CD-ROM Module

Ax2

L1x2L2X2

Ix2

Antennas(Optional)

Ax9

Ex1

Ex3

Ex4

Fx4

Ex3

Launch Board

Dx2

CPU Heat Sink

CPU

Cx2

Heat Plate

Modem Cover

Touch PadBoard

Touch PadButton

Speakers

FDD Module

Modem BoardDIMM

DIMM Cover

Bx2

LCD Module(See Next Page)

HDD Dummy Cover

HDD HDD Bracket

Ax1

Kx2

HDD Module

Ax2

Touch PadScroll Key

Touch PadFPC

Upper Case

Audio Board

PCMCIA Plate

Fan Module

Charger Plate

Wireless LAN Board (Optional)

RTC Battery

Chapter 3 59

LCD Module

3 LCD Cushions

LCD Bezel

LCD Panel

LCD BracketsLCD Coaxial

Cable

Ax3

Gx1 for 15” LCDGx2 for 14.1” LCD

Hx6 for Hitachi 15” Super XGA+ LCD Unit Gx4 for 14”1 XGA LCD UnitCx6 for Hitachi 15” XGA LCD Unit

Ox4 for 14.1 LCD only

LCD

Inverter

LCD Module

3 LCD Cushions

LCD Bezel

LCD Panel

LCD BracketsLCD Coaxial

Cable

Ax3

Gx1 for 15” LCDGx2 for 14.1” LCD

Hx6 for Hitachi 15” Super XGA+ LCD Unit Gx4 for 14”1 XGA LCD UnitCx6 for Hitachi 15” XGA LCD Unit

Ox4 for 14.1 LCD only

LCD

Inverter


Screw List

Item Description

A Screw M2.5XL6 Flat Head (Black)

B Screw M2XL3 Washer Flat Head (Black)

C Screw M2XL4 Flat Head (Black)

D Screw M2XL4 Round Head (Black)

E Screw M2XL5 Round Head (Silver)

F Hex Screw

G Screw M2.5XL4 Flat Head (Silver)

H Screw M2XL4.5 Flat Head (Silver)

I Screw M2XL3 Flat Head (Black)

J Screw M2XL12 Round Head (Black)

K Screw M3XL4 Flat Head (Silver)

L1 CPU Sink Screw 3kg-cm (Upper

L2 CPU Sink Screw 2kg-cm (Lower)

M Modem Special Screw M2XL4 Washer

N M2XL3 Flat Head (Silver)

O Screw M2XL3 Flat Head (Silver)

Chapter 3 61

Removing the Battery1. To remove the battery, push the battery release button, and then slide the battery out from the machine.


Removing the Hard Disk Drive Module1. See “Removing the Battery” on page 62

2. To remove the hard disk drive, first remove the one screw from the hard disk drive cover, and then remove the cover.

3. Remove the two screws as shown and then pull the plastic tag to detach the hard disk drive module out from the machine carefully.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive module to the main unit. It is suggested that you reverse the sequence when you remove the screws.

Disassembling the Hard Disk Drive Module1. See “Removing the Battery” on page 62

2. See “Removing the Hard Disk Drive Module” on page 63

3. To disassemble the hard disk drive module, first remove the two screws from the hard disk drive bracket.

Chapter 3 63

4. Detach the hard disk drive from the hard disk drive bracket.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive bracket to the hard disk drive module. It is suggested that you reverse the sequence when you remove the screws.


Removing the Memory Module1. See “Removing the Battery” on page 62

2. To remove the memory module from the machine, first remove the two screws from the memory cover.

3. Lift the cover off, then remove the memory cover.

4. Push out the latches on both sides of the socket and pull the memory module out from the socket.

Chapter 3 65

Removing the Modem Board1. See “Removing the Battery” on page 62

2. To remove the modem board, first remove the screw from the modem cover.

3. Remove the modem cover from the machine.

4. Remove two screws from the modem board as shown, then remove the modem board from the main unit carefully by using a plastic bladed screw driver.

5. Disconnect the modem cable from the modem board, then remove the modem board.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the modem board to the unit. It is suggested that you reverse the sequence when you remove the screws.


Chapter 3 67

Disassembling the LCD

Removing the Middle Cover1. See “Removing the Battery” on page 62

2. To remove the middle cover, first remove the two screws from the rear of the unit and then pry up the middle cover with a plastic flat screwdriver in the way as shown.

3. Disconnect the launch board cable from the launch board and then detach the middle cover away from the main unit.

.

Removing the Launch Board1. See “Removing the Battery” on page 62

2. See “Removing the Middle Cover” on page 68

3. Remove the two screws and then detach the launch board from the middle cover.


Removing the Keyboard1. See “Removing the Battery” on page 62


3. To remove the keyboard, first pull out and upward to expose the keyboard.

4. Use a plastic flat screwdriver to help disconnect the keyboard cable from the main board carefully, then remove the keyboard from the main board.

Removing the CD-ROM Drive Module1. See “Removing the Battery” on page 62


3. See “Removing the Keyboard” on page 69

4. Remove the one screw as shown here and then slide the CD-ROM drive module out from the main unit.

Chapter 3 69

Disassembling the CD-ROM Drive Module

1. See “Removing the Battery” on page 62



4. See “Removing the CD-ROM Drive Module” on page 69

5. To disassemble the CD-ROM drive module, first remove two screws as shown.

6. Remove the CD-ROM drive bracket from the CD-ROM drive module.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the CD-ROM drive bracket to the CD-ROM drive module. It is suggested that you reverse the sequence when you remove the screws.

Removing the Heat Plate1. See “Removing the Battery” on page 62



4. Remove the three screws as shown and then detach the heat plate from the main unit.


NOTE: 1.Because the CD-ROM module and the heat plate share the common screw, you only have to remove the two screws as shown below If you detach the heat plate from the main unit after the step of removing the CD-ROM. The same principle applies to the assembly procedures.

NOTE: 2.Please follow the numeric orders such as 1, 2, 3, and 4 to screw the heat plate to the main unit. It is suggested that you reverse the sequence when you remove the screws.

Removing the LCD Module1. See “Removing the Battery” on page 62



4. See “Removing the Heat Plate” on page 70

5. Remove the two screws from the base of the unit.

6. Disconnect the LCD coaxial cable from the main board.

Chapter 3 71

7. Remove the inverter cable from the main board with a plastic flat screwdriver.

8. Remove the LCD module from the main unit carefully.

9. Disconnect the launch board cable from the main board and remove it.

NOTE: Please arrange the inverter cable and the coaxial cable well in the way as shown after you connect them to the main board.


Removing the LCD Bezel1. See “Removing the Battery” on page 62




5. See “Removing the LCD Module” on page 71

6. Use plastic tweezers to remove the three LCD cushions on the LCD bezel, and then remove the three screws below from the LCD bezel.

7. Snap off the bezel carefully, and then remove the LCD bezel from the LCD module.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the LCD bezel to the LCD module It is suggested that you reverse the sequence when you remove the screws.

Chapter 3 73

Removing the Inverter Board (14.1” LCD)1. See “Removing the Battery” on page 62





6. See “Removing the LCD Bezel” on page 73

7. To remove the inverter board, first remove two screws from the inverter board.

8. Disconnect the LCD power cable and the inverter cable from the inverter board.

NOTE: 1. Please follow the numeric orders such as 1, 2, 3, and 4 to screw the inverter board to the LCD panel. It is suggested that you reverse the sequence when you remove the screws.

NOTE: 2. Please route the cables with the inverter cable placed at the right side of the coaxial cable as shown below before you attach the inverter board to the LCD panel.


Removing the Inverter Board (15” LCD)1. See “Removing the Battery” on page 62






7. To remove the inverter board, first remove one screw from the inverter board.

8. Disconnect the LCD power cable and the inverter cable from the inverter board.

NOTE: Please route the cables with the inverter cable placed at the right side of the coaxial cable as shown below before you attach the inverter board to the LCD panel.

Chapter 3 75

Removing the 14.1” TFT LCD1. See “Removing the Battery” on page 62






7. See “Removing the Inverter Board (14.1” LCD)” on page 74

8. To remove the LCD, first remove the four screws from the LCD, then remove the LCD from the LCD panel.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the LCD to the LCD panel. It is suggested that you reverse the sequence when you remove the screws.

Removing the 15” TFT LCD1. See “Removing the Battery” on page 62






7. See “Removing the Inverter Board (15” LCD)” on page 75

8. To remove the LCD, first remove the six screws from the LCD, then remove the LCD from the LCD panel.


NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the LCD to the LCD panel. It is suggested that you reverse the sequence when you remove the screws.

Removing the 14.1” TFT LCD Brackets1. See “Removing the Battery” on page 62







8. See “Removing the 14.1” TFT LCD” on page 76

9. Remove four screws on each side to remove the LCD brackets and then detach the LCD brackets from the LCD.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the LCD brackets to the LCD. It is

Chapter 3 77

suggested that you reverse the sequence when you remove the screws.

Removing the LCD Coaxial Cable1. See “Removing the Battery” on page 62







8. See “Removing the Inverter Board (15” LCD)” on page 75

9. Remove the tape then remove the LCD coaxial cable from the LCD.


Disassembling the Main Unit

Removing the RTC Battery1. See “Removing the Battery” on page 62




5. Disconnect the RTC cable and then remove the RTC battery from the upper case gently.

Removing the Touch Pad Frame1. See “Removing the Battery” on page 62

2. Use a plastic flat screwdriver to pry up the touch pad frame very carefully.

3. Detach the touch pad frame from the upper case gently.

Removing the Fan Module1. See “Removing the Battery” on page 62



4. To remove the fan, first remove the screw from the fan and then disconnect the fan cable from the main board by using a plastic flat screwdriver.

Chapter 3 79

5. Remove the other screw from the base of the unit, then remove the fan from the lower case.

Removing the CPU Heat Sink1. See “Removing the Battery” on page 62




5. See “Removing the Audio Board” on page 85

6. Remove four screws and then detach the CPU heat sink from the main unit.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the CPU heat sink to the main board. It is suggested that you reverse the sequence when you remove the screws.

Removing the Processor1. See “Removing the Battery” on page 62






6. See “Removing the CPU Heat Sink” on page 80

7. Use a flat screwdriver to unlock the CPU socket counter clockwise, detach the CPU from its socket and then lock the CPU socket clockwise with the flat screwdriver.

Installing the Processor1. See “Removing the Battery” on page 62






7. Use a flat screwdriver to unlock the CPU socket counterclockwise, attach the CPU into its socket and then lock the CPU socket clockwise with the flat screwdriver

NOTE: Please make sure the triangle mark on the CPU aligns with the one on the CPU socket.

Removing the Upper Case1. See “Removing the Battery” on page 62


Chapter 3 81






8. See “Removing the RTC Battery” on page 79

9. Use a plastic flat screwdriver to disconnect the touch pad cable from the main board.

10. To remove the upper case, first remove the nine screws from the base of the unit as shown.

11. Pull the upper case from the unit gently.

NOTE: 1. Important: If the notebook is installed with antennas and wireless LAN board, please disconnect the two RF cables from the sockets on the wireless LAN board before removing the upper case from the lower case. Any failure to do so will cause the damage to the two RF cables.

2. Please follow the numeric orders such as 1, 2, 3, and 4 to screw the upper case to the lower case. It

is suggested that you reverse the sequence when you remove the screws.


Removing the Touch Pad Board1. See “Removing the Battery” on page 62

2. See “Removing the Touch Pad Frame” on page 79

3. See “Removing the Upper Case” on page 81

4. To detach the touch pad board, first disconnect the touch pad cable from the touch pad board with a plastic flat screwdriver and plastic tweezers, and then remove the touch pad board from the upper case.

Removing the Touch Pad Button1. See “Removing the Battery” on page 62



4. See “Removing the Touch Pad Board” on page 83

5. Remove the touch pad button.

Removing the Touch Pad Scroll Key1. See “Removing the Battery” on page 62




5. See “Removing the Touch Pad Button” on page 83

6. Release the scroll key by pressing it downward gently and then detach it from the upper case.

Chapter 3 83

Removing the Touch Pad Cable1. See “Removing the Battery” on page 62




5. See “Removing the Touch Pad Button” on page 83

6. See “Removing the Touch Pad Scroll Key” on page 83

7. Remove the touch pad cable from the main board carefully.

8. Detach the touch pad cable from the upper case carefully.

Removing the Floppy Disk Drive Module1. See “Removing the Battery” on page 62









10. Remove the three screws as shown, and disconnect the FDD cable from the main board.


11. Detach the FDD module from the lower case.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the FDD module to the main board. It is suggested that you reverse the sequence when you remove the screws.

Removing the Audio Board1. See “Removing the Battery” on page 62









10. See “Removing the Floppy Disk Drive Module” on page 84

11. Detach the audio board from the main board and turn it over to disconnect the speaker cable from the audio board and then remove the audio board from the main unit.

NOTE: When assembling the audio board to the main board and the lower case, please make sure the audio board is attached with the pins inserted and the ports installed properly.

Chapter 3 85

Removing the Speakers 1. See “Removing the Battery” on page 62










11. Release the two latches which fix the left speaker to the lower case.

12. Lift up the cables and then detach the speakers from the lower case.

Removing the Charger Plate1. See “Removing the Battery” on page 62










10. To remove the charger plate, first remove the screw from the charger plate, and then remove the charger plate from the main board.

Removing the Main Board1. See “Removing the Battery” on page 62












13. See “Removing the Charger Plate” on page 86

14. Remove the three screws from the main board as shown below.

.

15. Detach the main board from the lower case carefully in the way as shown here.

Chapter 3 87

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the main board to the lower case. It is suggested that you reverse the sequence when you remove the screws.

Removing the PCMCIA Slot1. See “Removing the Battery” on page 62













14. See “Removing the Main Board” on page 87

15. Remove four screws from the PCMCIA plate to remove the plate.

16. Detach the PCMCIA slot from the main board.


NOTE: 1. Please follow the numeric orders such as 1, 2, 3, and 4 to screw the PCMCIA plate to the main board. It is suggested that you reverse the sequence when you remove the screws.

2. Please note that the I/O port bracket should be attached to the main board before assembling the

PCMCIA slot to the main board.

Removing the I/O Port Bracket1. See “Removing the Battery” on page 62













14. See “Removing the Main Board” on page 87

15. See “Removing the PCMCIA Slot” on page 88

16. Remove the four hex screws to detach the I/O port bracket from the main board.

Chapter 3 89

17. Detach the I/O port bracket from the main board.

NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the I/O port to the main board. It is suggested that you reverse the sequence when you remove the screws.


System Upgrade Procedure

Base Unit to Wireless Unit1. See “Removing the Battery” on page 62



4. See “Removing the Heat Plate” on page 70 (Remove three screws here)

5. Note that the one with the white RF cable is for the right antenna and the one with the black RF cable is for the left antenna.

6. Insert the wireless LAN board into its socket and press it down to secure well.

7. Attach the right antenna to the upper case and secure it with a screw. Route the cable as shown below.

8. Attach the left antenna to the upper case and secure it with a screw. Route the cable as shown below.

Chapter 3 91

9. Be careful to arrange the right and left RF cables well.

10. Connect the RF cables into the Wireless LAN board.

NOTE: Please note that the black RF cable should be routed beneath the coaxial cable.


Troubleshooting

Chapter 4

Use the following procedure as a guide for computer problems.

NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses.

1. Obtain the failing symptoms in as much detail as possible.

2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation.

3. Use the following table with the verified symptom to determine which page to go to.

Symptoms (Verified) Go To

Power failure. (The power indicator does not go on or stay on.)

“Power System Check” on page 95.

POST does not complete. No beep or error codes are indicated.

“Power-On Self-Test (POST) Error Message” on page 98

“Undetermined Problems” on page 106

POST detects an error and displayed messages on screen.

“Error Message List” on page 99

The diagnostic test detected an error and displayed a FRU code.

“System Diagnostic Diskette” on page 54

Other symptoms (i.e. LCD display problems or others).

“Power-On Self-Test (POST) Error Message” on page 98

Symptoms cannot be re-created (intermittent problems).

Use the customer-reported symptoms and go to “Power-On Self-Test (POST) Error Message” on page 98

“Intermittent Problems” on page 105

“Undetermined Problems” on page 106

Chapter 4 93

System Check Procedures

External Diskette Drive CheckDo the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required.

NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail.

Do the following to select the test device. See “System Diagnostic Diskette” on page 54 for details.

1. Boot from the diagnostics diskette and start the PQA program (see “System Diagnostic Diskette” on page 54).

2. Go to the diagnostic Diskette Drive in the test items.

3. Press m in the test items.

4. Follow the instructions in the message window.

If an error occurs with the internal diskette drive, first turn off the power and then reconnect the diskette connector to the system board.

If the error still remains:

1. Reconnect the external diskette drive/CD-ROM module.

2. Replace the external diskette drive/CD-ROM module.

3. Replace the system board.

External CD-ROM Drive CheckDo the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.

Do the following to select the test device:

1. Boot from the diagnostics diskette and start the PQA program (refer to “System Diagnostic Diskette” on page 54.

2. Go to the diagnostic CD-ROM in the test items.



If an error occurs, first turn off the power and then reconnect the connector to the system board. If the error still remains:

1. Reconnect the external diskette drive/CD-ROM module.

2. Replace the external diskette drive/CD-ROM module.



Keyboard or Auxiliary Input Device CheckRemove the external keyboard if the internal keyboard is to be tested.

If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board.

If the keyboard cable connection is correct, run the Keyboard Test. See “System Diagnostic Diskette” on page 54 for details.

If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a non-defective FRU:

1. Reconnect the keyboard cables.

2. Replace the keyboard.


The following auxiliary input devices are supported by this computer:

� Numeric keypad

� External keyboard

If any of these devices do not work, reconnect the cable connector and repeat the failing operation.

Memory CheckMemory errors might stop system operations, show error messages on the screen, or hang the system.

1. Boot from the diagnostics diskette and start the PQA program (please refer to “System Diagnostic Diskette” on page 54.

2. Go to the diagnostic memory in the test items.



NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System CheckTo verify the symptom of the problem, power on the computer using each of the following power sources:

1. Remove the battery pack.

2. Connect the power adapter and check that power is supplied.

3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the battery pack.

If you suspect a power problem, see the appropriate power supply check in the following list:

� “Check the Power Adapter” on page 96

� “Check the Battery Pack” on page 97

Chapter 4 95

Check the Power Adapter

Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure

1. If the voltage is not correct, replace the power adapter.

2. If the voltage is within the range, do the following:

� Replace the System board.

� If the problem is not corrected, see “Undetermined Problems” on page 106.

� If the voltage is not correct, go to the next step.

NOTE: An audible noise from the power adapter does not always indicate a defect.

3. If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and installation.

4. If the operational charge does not work, see “Check the Battery Pack” on page 97.

Pin 1: +19 to +20.5V

Pin 2: 0V, Ground


Check the Battery Pack

To check the battery pack, do the following:

From Software:

1. Check out the Power Management in control Panel

2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct.

3. Repeat the steps 1 and 2, for both battery and adapter.

4. This helps you identify first the problem is on recharging or discharging.

From Hardware:

1. Power off the computer.

2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure

3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.

To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.

If the battery status indicator does not light up, remove the battery pack and let it return to room temperature. Re-install the battery pack.

If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up, replace the DC/DC charger board.

Touchpad CheckIf the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a non-defective FRU:

1. Reconnect the touchpad cables.

2. Replace the touchpad.


After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No service actions are necessary if the pointer movement stops in a short period of time.

Chapter 4 97

Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first.

NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.

This index can also help you determine the next possible FRU to be replaced when servicing a computer.

If the symptom is not listed, see “Undetermined Problems” on page 106.

The following lists the error messages that the BIOS displays on the screen and the error symptoms classified by function.

NOTE: Most of the error messages occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured.

NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter Setup and install Setup defaults or correct the error.


Index of Error Messages

Error Code List

Error Codes Error Messages

006 Equipment Configuration Error

Causes:

1. CPU BIOS Update Code Mismatch

2. IDE Primary Channel Master Drive Error

3. IDE Secondary Channel Master Drive Error

(THe causes will be shown before “Equipment Configuration Error”)

010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

070 Real Time Clock Error

071 CMOS Battery Bad

072 CMOS Checksum Error

110 Incorrect password specified, system disabled. (Text mode only)

<No error code> Battery critical LOW

In this situation BIOS will issue 4 short beeps then shut down system, no message will show.

<No error code> Thermal critical High

In this situation BIOS will issue 3 long beeps then shut down system.

Error Message List

Error Messages FRU/Action in Sequence

Failure Fixed Disk Reconnect hard disk drive connector.

“Load Default Settings” in BIOS Setup Utility.

Hard disk drive

System board

Stuck Key see “Keyboard or Auxiliary Input Device Check” on page 95.

Keyboard error see “Keyboard or Auxiliary Input Device Check” on page 95.

Keyboard Controller Failed see “Keyboard or Auxiliary Input Device Check” on page 95.

Keyboard locked - Unlock key switch Unlock external keyboard

Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn BIOS ROM

System board

System RAM Failed at offset: nnnn DIMM

System board

Extended RAM Failed at offset: nnnn DIMM

System board

System battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.

System CMOS checksum bad - Default configuration used

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System timer error RTC battery


System board

Chapter 4 99

Real time clock error RTC battery


System board

Previous boot incomplete - Default configuration used

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Memory size found by POST differed from CMOS

Run “Load Default Settings” in BIOS Setup Utility.

DIMM

System board

Diskette drive A error Check the drive is defined with the proper diskette type in BIOS Setup Utility

See “External Diskette Drive Check” on page 94.

Incorrect Drive A type - run SETUP Check the drive is defined with the proper diskette type in BIOS Setup Utility

See “External Diskette Drive Check” on page 94.

System cache error - Cache disabled System board

CPU ID: System board

DMA Test Failed DIMM

System board

Software NMI Failed DIMM

System board

Fail-Safe Timer NMI Failed DIMM

System board

Device Address Conflict Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Allocation Error for device Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Failing Bits: nnnn DIMM

BIOS ROM

System board

Fixed Disk n None

Invalid System Configuration Data BIOS ROM

System board

I/O device IRQ conflict Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Operating system not found Enter Setup and see if fixed disk and drive A: are properly identified.

Diskette drive

Hard disk drive

System board

Error Message List

Error Messages FRU/Action in Sequence


Error Message List

No beep Error Messages FRU/Action in Sequence

No beep, power-on indicator turns off and LCD is blank.

Power source (battery pack and power adapter). See “Power System Check” on page 95.

Ensure every connector is connected tightly and correctly.

Reconnect the DIMM.

LED board.

System board.

No beep, power-on indicator turns on and LCD is blank.

Power source (battery pack and power adapter). See “Power System Check” on page 95.

Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

LCD

System board

No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external CRT.

Reconnect the LCD connectors.

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly.

System board

No beep during POST but system runs correctly. Speaker

System board

Error Beep List

Code Beeps Description

00h Two long beeps, one short beep, then one long beep. Success

F1h One long and one short beeps. BIOS file size mismatch

F2h One long and two short beeps BIOS reading error

D1h Two short beeps. Floppy drive not installed

Chapter 4 101

Index of Symptom-to-FRU Error Message

LCD-Related Symptoms

Symptom / Error Action in Sequence

LCD backlight doesn't work

LCD is too dark

LCD brightness cannot be adjusted

LCD contrast cannot be adjusted

Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system.

Reconnect the LCD connectors.

Keyboard (if contrast and brightness function key doesn't work).

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

Unreadable LCD screen

Missing pels in characters

Abnormal screen

Wrong color displayed

Reconnect the LCD connector

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

LCD has extra horizontal or vertical lines displayed.

LCD inverter ID

LCD inverter

LCD cable

LCD

System board

Indicator-Related Symptoms


Indicator incorrectly remains off or on, but system runs correctly

Reconnect the inverter board

Inverter board

System board

Power-Related Symptoms


Power shuts down during operation Power source (battery pack and power adapter). See “Power System Check” on page 95.

Battery pack

Power adapter

Hard drive & battery connection board

System board

The system doesn’t power-on. Power source (battery pack and power adapter). See “Power System Check” on page 95.

Battery pack

Power adapter

Hard drive & battery connection board

System board

The system doesn’t power-off. Power source (battery pack and power adapter). See “Power System Check” on page 95.

Hold and press the power switch for more than 4 seconds.

System board

Battery can’t be charged See “Check the Battery Pack” on page 97.

Battery pack

System board


PCMCIA-Related Symptoms


System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly

System board

PCMCIA slot pin is damaged. PCMCIA slot assembly

Memory-Related Symptoms


Memory count (size) appears different from actual size.

Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system.

DIMM

System board

Speaker-Related Symptoms


In Windows, multimedia programs, no sound comes from the computer.

Audio driver

Speaker

System board

Internal speakers make noise or emit no sound. Speaker

System board

Power Management-Related Symptoms


The system will not enter hibernation Keyboard (if control is from the keyboard)

Hard disk drive

System board

The system doesn't enter hibernation mode and four short beeps every minute.

See “Hibernation Mode” on page 28.

Press Fn+oand see if the computer enters hibernation mode.

Touchpad

Keyboard

Hard disk connection board

Hard disk drive

System board

The system doesn’t enter standby mode after closing the LCD


LCD cover switch

System board

The system doesn't resume from hibernation mode.



Hard disk drive

System board

The system doesn't resume from standby mode after opening the LCD.


LCD cover switch

System board

Battery fuel gauge in Windows doesn’t go higher than 90%.

Remove battery pack and let it cool for 2 hours.

Refresh battery (continue use battery until power off, then charge battery).

Battery pack

System board

Chapter 4 103

NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 106.

System hangs intermittently. Reconnect hard disk/CD-ROM drives.


System board

Peripheral-Related Symptoms


System configuration does not match the installed devices.

Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system.

Reconnect hard disk/CD-ROM/diskette drives.

External display does not work correctly. Press Fn+F5, LCD/CRT/Both display switching

See “System Diagnostic Diskette” on page 54.

System board

USB does not work correctly See “System Diagnostic Diskette” on page 54

System board

Print problems. Ensure the “Parallel Port” in the “Onboard Devices Configuration” of BIOS Setup Utility is set to Enabled.

Onboard Devices Configuration

Run printer self-test.

Printer driver

Printer cable

Printer

System Board

Serial or parallel port device problems. Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup Utility is set to Enabled.

Device driver

Device cable

Device

System board

Keyboard/Touchpad-Related Symptoms


Keyboard (one or more keys) does not work. Reconnect the keyboard cable.

Keyboard

System board

Touchpad does not work. Reconnect touchpad cable.

Touchpad board

System board

Modem-Related Symptoms


Internal modem does not work correctly. See “System Diagnostic Diskette” on page 54.

Modem phone port

modem combo board

System board

Power Management-Related Symptoms



Intermittent ProblemsIntermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.

When analyzing an intermittent problem, do the following:

1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.

2. If no error is detected, do not replace any FRU.

3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Chapter 4 105

Undetermined ProblemsThe diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).

NOTE: Verify that all attached devices are supported by the computer.

NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 95):

1. Power-off the computer.

2. Visually check them for damage. If any problems are found, replace the FRU.

3. Remove or disconnect all of the following devices:

� Non-Acer devices

� Printer, mouse, and other external devices

� Battery pack

� Hard disk drive

� DIMM

� CD-ROM/Diskette drive Module

� PC Cards

4. Power-on the computer.

5. Determine if the problem has changed.

6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:

� System board

� LCD assembly


Index of Phlash16 Error Message

Error Codes Error Message

-1 or // FF Memory allocation for Backup file buffer failed.

-2 or // FE BIOS.BAK already exists (rename or delete it)

-3 or // FD File Create failed on BIOS.BAK

-4 or // FC File Write failed on BIOS.BAK

-5 or // FB File Close failed on BIOS.BAK

-6 or // FA BIOS backup not supported in BIOS ROM file.

-7 or // F9 File Open failed on BIOS ROM file.

-8 or // F8 File Read failed on BIOS ROM file.

-9 or // F7 File Close failed on BIOS ROM file.

-10or // F6 Failed to locate signature bytes in BIOS ROM file.

-11 or // F5 Unsupported BIOS ROM file version.

-12 or // F4 V0.10 must fit ROM size and address within 1MB.

-13 or // F3 V2.00 must have block descriptor table and image buffer.

-14 or // F2 Device table has too many entries.

-15 or // F1 Device table has unsupported flash type.

-16 or // F0 Combined SAVE or RESTORE attributes in BIOS file.

-17 or // EF SAVE block without matching RESTORE block in BIOS file.

-18 or // EE V0.10 must have JMP table for platform procs.

-19 or // ED V2.00 must have OFFSET table for platform procs.

-20 or // EC BIOS file found errors in command line parameters.

-21 or // EB Part ID not found in table of supported parts.

-22 or // EA Allocation for BIOS ROM image failed.

-23 or // E9 Open failed on BIOS ROM file.

-24 or // E8 Read failed on BIOS ROM file.

-25 or // E7 Copy of REAL to EXTENDED memory buffer failed.

-26 or // E6 File close failed on BIOS.WPH.

-27or // E5 Cannot flash if Memory Managers (e.g. EMM 386) is present.

-28 or // E4 Attempt to read flash memory ID failed.

-29or // E3 BIOS ROM file failed to return flash memory ID.

-30 or // E2 Could not find BCP SYS block in BIOS.WPH file image.

-31 or // E1 File has different BIOS part number.

-32 or // E0 File contains same version of BIOS ROM image.

-33 or // DF Data written to flash does not match BIOS ROM image.

-34 or // DE Write to flash memory failed.

-35 or // DD Erase flash memory block failed.

-36 or // DC VPP is not at expected level.

-37 or // DB Erase sequence failed.

-38 or // DA New DMI string is too large.

-39 or // D9 Specified BIOS ROM file is not for this system.

-40 or // D8 Allocation for DMI OEM string failed.

-41 or // D7 No space for specified DMI OEM string in BIOS ROM.

-42 or // D6 DMI OEM strings require BCP DMI 0.1+.

-43 or // D5 Could not find BCP DMI block in BIOS ROM file image.

Chapter 4 107

-44 or // D4 Cannot flash if Memory Managers (e.g.HIMEM) is present.

-45 or // D3 BIOS ROM file maybe corrupt (checksum not zero).

-46 or // D2 BIOS ROM file size doesn’t match flash part size.

-47 or // D1 DMI system and chassis strings require BCP DMI 2.1+.

-48 or // D0 BIOS ROM file is older than (or same as) BIOS ROM image.

-49 or // CF Platform signature not found in the interface.

-50 or // CE Device descriptor signature not found in the interface.

-51 or // CD Part table signature not found in the interface.

-52 or // CC Invalid part count found in the interface.

-53 or // CB Invalid text descriptor size found in the interface.

-54 or // CA Invalid part descriptor size found in the interface.

-55 or // C9 Cannot flash when DOSKEY is present.

-56 or // C8 Duplicate device support found in the interface.

-57 or // C7 Program terminated due to command line option.

Error Codes Error Message


Index of PQA Diagnostic Error Code, Message

Error Code Message Action in Sequence

01XXX CPU or main board error Reload BIOS default setting.

System board

02XXX Memory error DIMM

System board

03XXX Keyboard error Reset Keyboard

Keyboard

System board

04XXX Video error System board

05XXX Parallel Port error System board

06XXX Serial port error System board

07XXX Diskette drive error Diskette drive

System board

08XXX Hard disk error Reload BIOS default setting

Hard disk

System board

09XXX CD-ROM error Reset CD-ROM cable

CD-ROM drive

System board

10XXX Co-processor error System board

11XXX Pointing device error Reset Keyboard

Keyboard

System board

12XXX Cache test error System board

Chapter 4 109


Jumper and Connector Locations

Chapter 5

Top View

PCB No. 02217-SB

CN1 CRT Port CN14 CardBus Connector

CN3 USB Port 0 CN15 Mini-PCI Connector

CN4 USB Port 1 CN16 CD-ROM Connector

CN6 Parallel Port CN17 Touch Pad Cable Connector

CN7 DC-in Port CN18 Internal Keyboard Cable Connector

CN8 Inverter Connector CN19 FDD Connector

CN9 Bluetooth Connector (Dummy) CN20 HDD Connector

CN10 Launch Cable Connector JK1 RJ45 + RJ11

Chapter 5 111

CN11 LCD Coaxial Cable Connector SW1 SW1 Setting (Please see below)

CN12 Fan Connector U18 CPU Socket

CN13 RTC Battery Connector U34 Golden Finger (or Debug Board)

Keyboard Switch Settings

SW1-1 SW1-2

English OFF OFF

Japanese ON OFF

Europe ON ON

Password Bypass Setting and BootBlock Setting

SW1-3 SW1-4

Check Password Enable ON OFF

BootBlock Enable OFF ON


Bottom View

CN21 Modem Card Cable Connector U65 North Bridge (845-GL)

CN22 Audio Board Connector U68 Cardbus Controller (OZ6912T)

CN23 Battery Connector U77 South Bridge (ICH4)

CN24 Modem Connector DM1 DIMM 1 Socket

U55 LVDS DM2 DIMM 2 Socket

U62 LAN Controller (RTL8100BL)

Chapter 5 113


FRU (Field Replaceable Unit) List

Chapter 6

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 230/280. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6 115

TravelMate 230 Exploded Diagram

116 TravelMate 230/280

Picture No. Partname Description

Cables

NS LCD COAXIAL CABLE 14.1" XGA CABLE LCD COAXIAL 14.1" XGA

7 LAUNCH BOARD CABLE CABLE LAUNCH BOARD S50

NS INVERTER CABLE CABLE LED & INVERTER

NS POWER CORD 125V 3PIN CORD 125V UL 3P K01081B1183WP

NS TOUCHPAD CABLE CABLE TOUCH PAD FPC PELICAN

NS MODEM CABLE CABLE MODEM 260MM

Chapter 6 117

Case/Cover/Bracket Assembly

5 BATTERY COVER COVER BATTERY PELICAN

NS LCD SUPPORT BRACKET LEFT 14"

BRACKET SUPPORT L 141 LCD S50

NS LCD SUPPORT BRACKET RIGHT 14"

BRACKET SUPPORT R 141 LCD S50

NS HDD BRACKET ASSEMBLY HDD BRACKET PELICAN

13 CHARGER PLATE ASSEMBLY CHARGER PLATE PELICAN

14 HEATSINK PLATE ASSEMBLY HEAT PLATE PELICAN

6 HDD COVER COVER HDD PELICAN



12 MODEM COVER W/SCREW ASSEMBLY MODEM COVER PELICAN

NS CD-ROM BRACKET BRACKET CD ROM PELICAN

10 UPPER CASE W/ TOUCHPAD MODULE

ASSEMBLY UPPER CASE PELICAN

NS TOUCHPAD COVER FRAME TOUCHPAD PELICAN

11 MIDDLE COVER W/O LAUNCH BOARD

COVER MIDDLE PELICAN

NS LCD BEZEL 14.1" W/ NAME PLATE & RUBBER

ASSEMBLY BEZEL 14.1"

NS LCD PANEL W/ HINGE BRACKET, LATCH & LOGO

ASSEMBLY PANEL 14.1"


Chapter 6 119

1 LOWER CASE W/ DIMM COVER & SPEAKER PACK

ASSEMBLY LOWER CASE PELICAN

NS DIMM COVER W/ SCREW ASSEMBLY DIMM COVER PELICAN

NS PCMCIA SLOT CONN CARDPUSH 1CA91501-TC-F2

NS I/O BRACKET ASSEMBLY I/O BRACKET PELICAN

NS PCMCIA PLATE ASSEMBLY PCMCIA PLATE PELICAN

Boards

NS AUDIO BOARD PELICAN AUDIO BD (SMT) VER-0SA

NS INVERTER BOARD 14"/15"AMBIT INVERTER 14"/15" T62I223.00



8 MODEM BOARD AMBIT T60M283.00

MODEM MDC AMB/T60M283.00

3A/3B

NS LAUNCH BOARD PELICAN LAUNCH KEY BD

NS WIRELESS BOARD AMBIT T60H656.00

LAN WLESS PCI AMBIT T60H656.00

NS TOUCHPAD BOARD TOUCHPAD MULTI-SWITCH SYNAPTIC

Battery

NS BATTERY MODULE 8CELL SAMSUNG

BATTERY MODULE 8CELL

16 BATTERY 8CELL LI-ION SAMSUNG BTP-43D1

ASY BTY PACK LI+8C 2AH/SAM SMP


Chapter 6 121

NS COIN BATTERY 3V 210MAH BTY COIN 3V CR2032WKA2 210MAH

Adapter

NS ADAPTER 70W 3PIN DELTA ADP-65DBBE

ADT 70W ADP-65DBBE 3P

Keyboard

NS KEYBOARD NSK-84X21 US KB US NSK-84X21

Speaker

NS SPEAKER PACK LEFT/RIGHT SPEAKER PELICAN

Heatsink

3 CPU HEATSINK SINK HEAT CPU PELICAN

Fan

17 CPU FAN SINK W/ FAN ASSEMBLY FAN PELICAN

FDD/Floppy Disk Drive



15 FDD MODULE 1.44M MITSUMI ASSY UNIT FDD MITSUMI PELICAN

CD-ROM DRIVE

18 CD-ROM 24X MITSUMI SR244W1 CD-ROM 24X MITSU/SR244W1 F4M

NS DVD-ROM 8X MKE/SR-8177-BAA6 DVD-ROM 8X MKE/SR-8177-BAA6 F4M

Main board

9 MAINBOARD PELICAN W/ COIN BATTERY, I/O BRACKET, MODEM CABLE, PCMCIA PLATE & PCMCIA SLOT

PELICAN MB (DIP) W/O CPU VER-SB

Miscellaneous

NS TOUCHPAD BUTTON SCROLL BUTTON TOUCHPAD SCROLL

NS TOUCHPAD BUTTON PAD BUTTON TOUCHPAD PELICAN


Chapter 6 123

NS SCREW RUBBER UPPER RUBBER UP 14.1" BEZEL F3M

NS SCREW RUBBER LOWER RUBBER SCREW DOWN F3M

NS NAME PLATE FOR BEZEL MYLAR NAME PLATE PELICAN

NS LOGO LABEL FOR PANEL LABEL LOGO ON PANEL PELICAN

NS NAME PLATE FOR MIDDLE COVER TM230

MYLAR PLATE NAME COVER MIDDLE

NS LAUNCH KEY KEY LAUNCH PELICAN

Screws

NS SCREW SCR. HEX NUT W/WASHER&NYLOK #4

NS SCREW SCREW M2L12 PH MSN+BZ

21 SCREW SCREW CPU MECH WAFER M2*L4 NI

23 SCREW SCREW M2.0*12 STEEL B

24 SCREW SCREW M2L4 BH MSN+BZ

25 SCREW SCREW M2L5 BH MSN+N

NS SCREW SCREW M2*3 NYLON 1JMCPC-420325

26 SCREW SCREW

27 SCREW SCREW M2.5X6

NS SCREW SCREW M3x4(86.9A524.4R0)

NS SCREW SCREW WAFER NYLOK NI 2ML3

NS SCREW SCREW M2.5*4L NI



TravelMate 280 Exploded Diagram

Chapter 6 125


Cables

NS LCD COAXIAL CABLE 15” XGA CABLE LCD COAXIAL 15” XGA

7 LAUNCH BOARD CABLE CABLE LAUNCH BOARD S50

NS INVERTER CABLE CABLE LED & INVERTER

NS POWER CORD 125V 3PIN CORD 125V UL 3P K01081B1183WP

NS TOUCHPAD CABLE CABLE TOUCH PAD FPC PELICAN

NS MODEM CABLE CABLE MODEM 260MM


Case/Cover/Bracket Assembly

5 BATTERY COVER COVER BATTERY PELICAN

NS HDD BRACKET ASSEMBLY HDD BRACKET PELICAN

13 CHARGER PLATE ASSEMBLY CHARGER PLATE PELICAN

14 HEATSINK PLATE ASSEMBLY HEAT PLATE PELICAN

6 HDD COVER COVER HDD PELICAN

12 MODEM COVER W/SCREW ASSEMBLY MODEM COVER PELICAN

NS CD-ROM BRACKET BRACKET CD ROM PELICAN


Chapter 6 127

10 UPPER CASE W/TOUCHPAD MODULE

ASSEMBLY UPPER CASE PELICAN

NS TOUCHPAD COVER FRAME TOUCHPAD PELICAN

11 MIDDLE COVER W/O LAUNCH BOARD

COVER MIDDLE PELICAN

NS LCD BEZEL 15" W/ NAME PLATE & RUBBER

ASSEMBLY BEZEL 15"

NS LCD PANEL W/ HINGE BRACKET LATCH & LOGO

ASSEMBLY PANEL 15"

1 LOWER CASE W/ DIMM COVER & SPEAKER PACK

ASSEMBLY LOWER CASE PELICAN

NS DIMM COVER W/ SCREW ASSEMBLY DIMM COVER PELICAN



NS PCMCIA SLOT CONN CARDPUSH 1CA91501-TC-F2

NS I/O BRACKET ASSEMBLY I/O BRACKET PELICAN

NS PCMCIA PLATE ASSEMBLY PCMCIA PLATE PELICAN

Boards

NS AUDIO BOARD PELICAN AUDIO BD (SMT) VER-0SA

NS INVERTER BOARD 14"/15"AMBIT INVERTER 14"/15" T62I223.00

8 MODEM BOARD AMBIT T60M283.00

MODEM MDC AMB/T60M283.00

3A/3B

NS LAUNCH BOARD PELICAN LAUNCH KEY BD


Chapter 6 129

NS TOUCHPAD BOARD TOUCHPAD MULTI-SWITCH SYNAPTIC

Battery

NS BATTERY MODULE 8CELL SAMSUNG


16 BATTERY 8CELL LI-ION SAMSUNG BTP-43D1

ASY BTY PACK LI+8C 2AH/SAM SMP

NS BATTERY MODULE 8CELL LI-ION SANYO


16 BATTERY MODULE 8CELL LI-ION SANYO 4UR1865OF-2

BTY PACK LI+8CELL 2AKH SANYO

NS COIN BATTERY 3V 210MAH BTY COIN 3V CR2032WKA2 210MAH



NS ADAPTER 70W 3PIN DELTA ADP-65DBBE

ADT 70W ADP-65DBBE 3P

Keyboard

NS KEYBOARD NSK-84X21 US KB US NSK-84X21

Speaker

NS SPEAKER PACK LEFT/RIGHT SPEAKER PELICAN

Heatsink

3 CPU HEATSINK SINK HEAT CPU PELICAN

Fan

17 CPU FAN SINK W/ FAN ASSEMBLY FAN PELICAN

FDD/Floppy Disk Drive

15 FDD MODULE 1.44M MITSUMI ASSY UNIT FDD MITSUMI PELICAN

Combo Drive


Chapter 6 131

NS COMBO DRIVE 8/24/10/24X KME UJA74OAC6 F4

COMBO 8,24/10/24 UJA74OAC6 F4

Main board

9 MAINBOARD PELICAN W/ COIN BATTERY, I/O BRACKET, MODEM CABLE, PCMCIA PLATE & PCMCIA SLOT

PELICAN MB (DIP) W/O CPU VER-SB

Miscellaneous

NS TOUCHPAD BUTTON SCROLL BUTTON TOUCHPAD SCROLL

NS TOUCHPAD BUTTON PAD BUTTON TOUCHPAD PELICAN

NS SCREW RUBBER UPPER RUBBER UP 14.1" BEZEL F3M

NS SCREW RUBBER LOWER RUBBER SCREW DOWN F3M

NS NAME PLATE FOR BEZEL MYLAR NAME PLATE PELICAN



NS LOGO LABEL FOR PANEL LABEL LOGO ON PANEL PELICAN

4 NAME PLATE FOR MIDDLE COVER TM280

MYLAR PLATE NAME TM280 MIDDLE

Screws

21 SCREW SCREW CPU MECH WAFER M2*L4 NI

23 SCREW SCREW M2.0*12 STEEL B

24 SCREW SCREW M2L4 BH MSN+BZ

25 SCREW SCREW M2L5 BH MSN+N

NS SCREW SCREW M2*3 NYLON 1JMCPC-420325

26 SCREW SCREW

27 SCREW SCREW M2.5X6

NS SCREW SCREW M3x4(86.9A524.4R0)

NS SCREW SCREW WAFER NYLOK NI 2ML3

NS SCREW SCREW M2.5*4L NI


Chapter 6 133


Model Definition and Configuration

Appendix A

Model Number Definition

Model Number

LCD CPU Memory HDD CD/DVD Battery

230X 14.1” TFT Celeron 1.7G 128/256MB 20GB 24X CD-ROM Li-ion

230FX 14.1” TFT Celeron 1.7G 128MB 20GB 24X CD-ROM Li-ion

230XV 14.1” TFT Celeron 1.7G 128/256MB 20GB/30GB

8X DVD-ROM Li-ion

230FXV 14.1” TFT Celeron 1.7G 128MB 20GB 8X DVD-ROM Li-ion

230XC 14.1” TFT Celeron 1.7G 256MB 30GB Combo Li-ion

230LC 15” TFT Celeron 1.7G 256MB 30GB Combo Li-ion

231X 14.1” TFT Celeron 1.8G 128MB 20GB 24X CD-ROM Li-ion

231XV 14.1” TFT Celeron 1.8G 128MB 20GB 8X DVD-ROM Li-ion

281X 14.1” TFT Pentium 4M 1.8G 256MB 20GB/30GB

24X CD-ROM Li-ion

280FX 14.1” TFT Pentium 4M 1.8G 256MB 20GB 24X CD-ROM Li-ion

281XC 14.1” TFT Pentium 4M 1.8G 256MB 20GB/30GB

Combo Li-ion

281XV 14.1” TFT Pentium 4M 1.8G 256MB 20GB/30GB

8X DVD-ROM Li-ion

280FXV 14.1” TFT Pentium 4M 1.8G 256MB 20GB 8X DVD-ROM Li-ion

283X 14.1” TFT Pentium 4M 2.0G 256MB 20GB 24X CD-ROM Li-ion

283XC 14.1” TFT Pentium 4M 2.0G 256MB 20GB Combo Li-ion

281LC 15” TFT Pentium 4M 1.8G 256MB 30GB Combo Li-ion

Appendix A 135


Test Compatible Components

Appendix B

This computer’s compatibility is a test plan released by Acer Internal Testing Department. Once the final report is available, this chapter will be revised accordingly.

Appendix B 137

Microsoft Windows XP Environment Test

Item Specifications

Processor Intel Pentium IV Northwood 1.7 GHz,

Intel Pentium IV Northwood 1.8 GHz,





Intel Celeron Northwood 1.6 GHz,





Memory

DDR SDRAM PC1600/2100

128MB Infineon HYS64D16000GDL-7-B

128MB Nan-Ya NT128D64SH4B0GM-75B

128MB Micron MT4VDDT1664HG-265B2

256MB Mitsubishi MH2D64AKS-75-JE



256MB Micron MT8VDDT3264HDG-265B3

512MB Mitsubishi MH64D64AKQH-75

512MB Infineon HYS64D64020GDBL-7-B

LCD 14.1” XGA TFT

IDT ITXG77C

AU B141XN04 V2/4 XXX

LG LP141X-AH

15” XGA TFT

Hitachi TX38D85VC1CAB

AU B150XG01 V.0

CMO N150X3-L01

15” SXGA TFT

Hitachi TX38D95VC1CAM

Hard Disk Drive 20GB Hitachi DK23EA-20F

20GB Toshiba MK2018GAP

30GB Hitachi DK23EA-30F


30GB Fujitsu HN-16L/30

40GB Hitachi DK2EA-40





Floppy Disk Drive Mitsumi D353G

MCI JU-226A033

DVD-ROM Drive 8X MKE SR-8177-BAA6


CD-ROM Drive Mitsumi SR-244W1

DVD/CD-RW Combo KME UJDA740

AC Adapter (3 pin) Delta 70W

Liteon 70W

Power Cord King Cord

Battery Li-Ion, 8 cells Samsung, Li-Ion 8cells

Sanyo, Li-Ion 8cells

Network Adapters

LAN Ethernet/10baseT/100baseT 3Com Etherlink III 3C589D

IBM EtherJet CardBus Adapter 10/100

Intel Ether Express Pro/100 Mobile Adapter MBLA3200

Xircom CardBus Ethernet 10/100 32 Bit CBE-10/100BTX

Multifunction Card (Combo) 10/100 EtherJet CardBus Real Port w/ 56K modem 34L1301

3Com Megahertz 10/100 LAN + 56K Modem PC Card

Xircom Realport CardBus Ethenet 10/100 + Modem 56

LAN Token Ring IBM Token Ring 16/4 Adapter II

IBM Turbo 16/4 Token Ring

Olicom Token Ring GoCard

Wireless LAN Card IBM Wireless LAN Cardbus Adapter

Intel Pro-Wireless LAN PC Card

Proxim Skyline 802.11a Cardbus PC Card

Modem Adapters

Modem (up to 56K) 3Com Megahertz 56K Modem PC Card

Xircom Credit Card Modem 56

IBM 56K Double Jack Modem

ISDN US Robotics Megahertz 128K ISDN Card 405R17T7117M

IBM OBI International ISDN PC Card

IBM ISDN Card D5K3320

I/O Peripheral

I/O - Display Acer 211c 21”

Viewsonic PF790 19”

Acer FP751 17” TFT LCD

IBM Color TFT LCD 14”

Compaq Color Monitor

NET Color Monitor 20”

Mozo 17” TFT LCD (DVI)

I/O - Projector NEC MultiSync MT-1040

I/O - Parallel (Printer/Scanner) Canon BJC-600J

Epson Stylus Color 740 Parallel Interface

HP DeskJet 890CDEskjet 880C Parallel Interface

HP LaserJet 6MP

HP LaserJet 2200

AcerScan Prisa 620P

Item Specifications

Appendix B 139

I/O - USB Keyboard/Mouse Chicony USB Keyboard

IBM USB Numeric Keypad

Microsoft Natural Keyboard Pr

Acer Aspire USB mouse

Logicool US Mouse

Logitech Cordless Mouseman Wheel USB Interface

Logitech USB Wheel Mouse

Microsoft IntelliMouse Optical USB Interface

I/O - USB (Printer/Scanner) Epson Stylus Color 740 USB interface

HP DeskJet 880C USB interface

Canon CanonScan D1250 (USB 2.0, JP OS only)

HP ScanJet 3300C Color Scanner

I/O - USB (Speaker/Joystick)) JS USB Digital Speaker

Panasonic USB Speaker EAB-MPC57USB

AIWA Multimedia Digital Speaker

Microsoft SideWinder Precision Pro Joystick

Logitech WingMan RumblePad

I/O - USB Camera Intel Easy PC Camera

Logitech QuickCam Express Internet

Nikon Supernign-Performance 3X Zoom

I/O - USB Storage Drive Logitech CDRW +DVDROM combo USB interface

Iomega USB Zip 250MB

Argosy Ultra Slim CDRW (USB 2.0)

Plextor Burn-Proof CDRW (USB 2.0)

Fujitsu MO-1300 1.3G (USB 2.0)

Fujitsu 20GB HDD (USB 2.0)

Sony DVD-ROM (USB 2.0)

IO-Data DVDROM (USB 2.0)

IBM 32MB USB Memory Key

Trek 32MB USB Memory

I/O - USB Hub Belkin 4 Port USB Hub

Eizo I Station USB Hub

Elecom USB Hub 4 Port

Sanwa USB Hub 4 Port

4 Port Hub USB 2.0

I/O - 1394 Storage Drive Logitec Firmware CDRW + DVDROM Combo

Yamaha Firewire 8824 CDRW

Buffalo Firewire HD I.LINK 20GB

I-O Data Firewire HD I.LINK 30GB

Lacie Firewire HD I.LINK 30GB

VST Firewire HD

I/O - 1394 Scanner UMAX Firewire PowerLook 110

I/O - 1394 Camera Sony DV DCR-TRV10

I/O - Access Point (802.11b) Hitachi DC-CN3300

Lucent RG-1000

Lucent WavePoint-II

Cisco Aironet 350

Orinoco AP-500

I/O Acess Point (802.11a/b) Intel Dual Pro/Wireless 5000

I/O Acess Point (802.11a) Intel Pro/Wireless 5000

PCMCIA

Item Specifications


PCMCIA - ATA IBM Microdrive 340MB

IBM Microdrive 1G

Iomega Click! 40MB

PCMCIA - USB 2.0 Apricorn EZ-USB2.0 Cardbus PC Card

PCMCIA - 1394 Buffalo 1394 Interface Cardbus IFC-ILCB/DV

I-O Data 1394 Interface Cardbus CB1394/DVC

Pixela 1394 Cardbus PC Card PIX-PCMC/FW1

PCMCIA - Bluetooth IBM Community Bluetooth PC Card

Toshiba Bluetooth PC Card

Item Specifications

Appendix B 141

Microsoft Windows 2000 Environment Test

Item Specifications












Memory











LCD 14.1” XGA TFT

IDT ITXG77C


LG LP141X-AH

15” XGA TFT


AU B150XG01 V.0

CMO N150X3-L01

15” SXGA TFT













MCI JU-226A033






Liteon 70W




Network Adapters














Modem Adapters







I/O Peripheral












HP LaserJet 6MP

HP LaserJet 2200

AcerScan Prisa 620P

Item Specifications

Appendix B 143





Logicool US Mouse






























4 Port Hub USB 2.0






VST Firewire HD




Lucent RG-1000

Lucent WavePoint-II

Cisco Aironet 350

Orinoco AP-500



PCMCIA

Item Specifications



IBM Microdrive 1G

Iomega Click! 40MB







Item Specifications

Appendix B 145

Microsoft Windows 98 Environment Test

Item Specifications












Memory











LCD 14.1” XGA TFT

IDT ITXG77C


LG LP141X-AH

15” XGA TFT


AU B150XG01 V.0

CMO N150X3-L01

15” SXGA TFT













MCI JU-226A033






Liteon 70W




Network Adapters














Modem Adapters







I/O Peripheral












HP LaserJet 6MP

HP LaserJet 2200

AcerScan Prisa 620P

Item Specifications

Appendix B 147





Logicool US Mouse






























4 Port Hub USB 2.0






VST Firewire HD




Lucent RG-1000

Lucent WavePoint-II

Cisco Aironet 350

Orinoco AP-500



PCMCIA

Item Specifications



IBM Microdrive 1G

Iomega Click! 40MB







Item Specifications

Appendix B 149


Online Support Information

Appendix C

This section describes online technical support services available to help you repair your Acer Systems.

If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.

Acer's Website offers you convenient and valuable support resources whenever you need them.

In the Technical Information section you can download information on all of Acer's Notebook, Desktop and Server models including:

� Service guides

� User's manuals

� Training materials

� Main manuals

� Bios updates

� Software utilities

� Spare parts lists

� Chips

� TABs (Technical Announcement Bulletin)

For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our technical material.

Also contained on this website are:

� Detailed information on Acer's International Traveller’s Warranty (ITW)

� Returned material authorization procedures

� An overview of all the support services we offer, accompanied by a list of telephone, fax and email contacts for all your technical queries.

We are always looking for ways to optimize and improve our services, so if you have any suggestions or comments, please do not hesitate to communicate these to us.

Appendix C 151


Index

AAC Adapter 27

Audio 18

BBattery 25

battery pack

charging indicator 12

BIOS 18

package 18ROM size 18ROM type 18vendor 18Version 18

BIOS Setup Utility 33

BIOS Supports protocol 18

BIOS Utility 33

Load Default Settings 50Navigating 35System Information 36System Security 45

Board Layout 5

Bottom View 6Top View 5

brightness

hotkeys 15

CCache

controller 18size 18

caps lock

on indicator 12

CardBus 25

CD-ROM Interface 21

Chipsets 18

computer

on indicator 12

contrast

hotkeys 15

Controllers 18

Core logic 18

CPU

core voltage 18

I/O voltage 18package 18type 18

DDC-AC LCD Inverter 26

DC-DC/Charger 25

DIMM 19

Combinations 19package 19Speed 19voltage 19

Disassembly

Machine 57

Disassembly Flowchart 59

Display 2

display

hotkeys 15

Display Standby Mode 28

DMA Channel Assignment 31

DVD-ROM Interface 21

EEnvironmental Requirements 28

Error Symptom-to-Spare Part Index 98

External CD-ROM Drive Check 94

External Diskette Drive Check 94

FFeatures 1

Flash Utility

PHLASH Utility 52

Floppy Disk Drive Interface 20

FRU (Field Replaceable Unit) List 115

H

Hard disk 18, 20

Hard Disk Drive Module

Disassembly 63

Hard Disk Standby Mode 28

Hardware Specifications and Configurations 18

HDD 18, 20

Hibernation Mode 28

Hibernation mode

Index 153

hotkey 15

Hot Keys 15

II/O Address Map 29

Indicators 12

Intermittent Problems 105

IRQ Assignment Map 31

JJumper and Connector Locations

Bottom View 113SW2 Settings 112Top View 111, 113

KKeyboard 18, 25

Keyboard or Auxiliary Input Device Check 95

LL2 cache 18

LCD 26

MMachine Disassembly 57

Mechanical Specification 28

media access

on indicator 12

Memory

Address Map 29

Memory Address Map 29

Memory Check 95

Modem 20

NNotebook Manager

hotkey 15

num lock

on indicator 12

OOnline Support Information 151

PPanel 6

Bottom 11right 9

Parallel Port 24

parallel port

setting in BIOS Utility 44

Password Setting

Hard Disk Password 47Power-On Password 47Setup Password 47

PC Card 12, 25

PCMCIA 25

Power Management 28

Power management 2

Power System Check 95

Battery Pack 97Power Adapter 96

PQA 54

Processor 18

RRemoving the Battery Pack 62

RMA 115

RTC 18

SSecond Level Cache 18

speakers

hotkey 15

Standby Mode 28

Super I/O 18

System

Block Diagram 4Layout 5

System Check Procedures 94

System Diagnostic Diskette 54, 93

System Memory 19

System Utilities 33

System Utility Diskette 53

TTemperature 28

Test Compatible Components 137

Touchpad 18

touchpad

hotkey 15

Touchpad Check 97

Troubleshooting 93

UUndetermined Problems 106

USB 25


VVideo 24

Resolutions 24

Video controller 18

WWindows 2000 Environment Test 142

Windows 98 Environment Test 146

Windows XP Environment Test 138

Index 155


Date post:	21-Feb-2015
Category:	Documents
Upload:	mmihmmih2003
View:	386 times
Download:	3 times

Service Manual Travel Mate 230

Documents