• Full bore design• Large internal bypass• Premium carbide slips and drag blocks• Hydraulic actuated hold down system• Available in several J-slot configurations, manual and auto
HD Squeeze PackerC O M P R E S S I O N
Operation:
Tacticals HD Compression Squeeze Packer is used for high pressure production testing, squeezing cementing, acidizing and fracturing. The HD Compression Squeeze Packer has an integral by-pass system that allows circulation around the tool to remove cement and debris from the well.
The HD CS Packer is used with the TS-U Bridge Plug for multiple zone operations.
Characteristics:
www.TacticalCompletions.com | 1(800)239-90521
• Full bore design• Emergency rotational release system• Holds pressure from above and below• External J-Slot design reduces debris build up
Squeeze PackerT E N S I O N
Operation:
Tacticals Tension Squeeze Packer is a full bore tension set packer that holds pressure from above and below. It is used where sufficient tubing weight is not available to achieve pack off with compression set squeeze packers.
The Tension Packer is used for squeeze cementing operations, casing testing, formation fracturing and high pressure acidizing.
It is run in conjunction with the SC Unloader which allows circulation around the tool and equalizes tubing and annulus pressures during retrieving.
Characteristics:
www.TacticalCompletions.com | 1(800)239-90522
J-TRACKTENSION SQUEEZE PACKER
Operation:
Tactical offers the upgraded J Track full bore tension squeeze packer that holds pressure from above and below. The SC-2 unloader is run in tandem with the squeeze packer and is used where sufficient tubing weight is not available to achieve pack off with compression set squeeze packers.
The NEW J-Track design allows for the squeeze packer to be run in tandem with either a Right-Hand or Left-Hand Set TITAN Retrievable Bridge Plug and most other plugs.
Additional improvements have been made to the J-Track Tension Squeeze Packer such as the drag block and gauge ring change out.
Characteristics:• New J-Track Configuration for use with RH or LH Set TITAN RBP• Emergency Rotational Release System• 10,000 psi (69MPA) rated from above and below• Carbide Premium Slips• Full Open Bore Design• Fewer Parts Needed To Change Casing Weight Configuration than previous versions
in mm lbs/ft kg/m in mm in mm in mm9.5-13.5 14.1-20.1 3.750 95.25 3.92 99.57 4.09 103.89 TC621-45A-00513.5-15.1 20.1-22.5 3.625 92.08 3.83 97.18 3.92 99.57 TC621-45B-00518.0-21.4 26.8-31.8 4.000 101.60 4.13 104.80 4.28 108.61 TC621-55A-00511.5-15.0 17.1-22.3 4.125 104.80 4.41 111.96 4.58 115.82 TC621-50B-00514.0-20.0 20.8-29.8 4.625 117.48 4.78 121.41 5.01 127.25 TC621-55A-00520.0-23.0 29.8-34.2 4.500 114.30 4.67 118.62 4.78 121.41 TC621-55B-00526.0-32.0 38.7-47.6 5.875 149.23 6.09 154.79 6.28 159.41 TC621-70A-00517.0-23.0 27.0-34.2 6.000 152.40 6.37 151.70 6.54 166.07 TC621-70B-00533.7-39.0 50.2-58.1 6.453 163.91 6.63 168.28 6.77 171.83 TC621-75A-00524.0- 29.7 35.7- 44.2 6.672 169.47 6.88 174.63 7.03 178.44 TC621-75B-005
177.8
193.77-5/8
7
CasingSize
114.34½
127.05"
139.75½
ProductNumber
MaximumMinimum
Setting RangeDimensions
CasingWeight
** Other sizes available upon request.
www.TacticalCompletions.com | 1(800)239-9052 3
• Full open bore• Large by-pass area• Heavy duty collet for repeated use• Permits full circulation around packer• Simple operation (tension to close-compression to open)
SC Unloader
Operation:
The SC Unloader is a tension set unloader usually run above the Tension Squeeze Packer to equalize tubing and annulus pressure differentials. With the heavy duty collet the SC Unloader can be left in the open position allowing fluid to pass while running, retrieving and preventing the packer elements from swabbing.
Characteristics:
in1-1/42-3/82-3/82-3/8
lbs/ft2.2503.2503.7504.500
in.750
1.6252.00
2.500
in1.660 EU 10RD2-3/8 EUE 8RD2-3/8 EUE 8RD2-7/8 EUE 8RD
mm31.7560.360.373.0
kg/m57.1582.5595.25
114.30
mm19.0541.2850.8063.50
mm42.1660.3060.3073.00
TC 525-04A-000
TC 525-06A-000
TC 525-20A-000
TC 525-25A-000
Tubing Size
MaxO.D.
MinI.D.
Thread Connection Product
Number
www.TacticalCompletions.com | 1(800)239-90524
MC Valve
Operation:
The MC Valve is used with the Casing Packer to cement liner strings into the well bore or open hole. The Casing Packer is set in compression allowing the MC Valve to shear at a pre determined valve, opening the cementing ports. The cementing ports are closed by picking up on the casing string.
in4-1/2 LTC5-1/2 LTC
in5.5006.500
in4.0005.000
in6” & UP6” & UP
mm114.3139.7
mm139.7165.1
mm101.6127
mm42.1660.30
TC525-04A-000TC525-06A-000
Casing Size
MaxO.D.
MinI.D.
HoleSize Product
Number
www.TacticalCompletions.com | 1(800)239-90525
• No drilling required• Short compact design• Meets tubing yield strength
Pump Out Cement Sleeve
Operation:
The Pump Out Cementing Sleeve is used for cementing liner strings in the well bore and run above the Casing Packer. The Pump Out Cementing Sleeve is run above the Casing Packer.
When the Casing Packer is set in (Tension or Compression) the Pump Out Cementing Sleeve is activated by gravitating a ball into the lower seat causing applied pressure shifts and opens port holes for cementing.
After the cementing operation is completed, the wiper plug is pumped into the upper seat and pressure is applied to shift the closing sleeve over the port holes. Final pressure of 2,500 PSI will pump out all internal parts of the Pump Out Cementing Sleeve.
Characteristics:
in2-3/82-7/83-1/24.0
4-1/25-1/2
in3.1253.7504.5004.6255.5006.500
in2.0002.5003.0003.4504.0005.000
in2-3/8 EU 8RD2-7/8 EUE 8RD3-1/2 EUE 8RD
4.0 NU 8RD4-1/2 8RD CSG5-1/2 8RD CSG
mm60.373
88.9101.6114.3139.7
mm79.495.25114.3117.47139.7165.1
mm50.8063.5076.2087.70101.6127.0
mm60.373
88.9101.6114.3139.7
TC218-20A-000
TC218-25A-000
TC218-35A-000
TC218-40A-000
TC218-45A-000
TC218-55A-000
Size MaxO.D.
Min I.D.@ Pump-
Out
Thread Connection
Product Number
www.TacticalCompletions.com | 1(800)239-90526
• Constructed with drillable materials• 35 MPA (5,000 psi) and 41 MPA (6,000 psi) rated• Temperature rating 93 degrees Celsius or 200 degrees Fahrenheit• Runs on existing wireline setting tool or hydraulic setting tools
O M E G A 5 & 6B R I D G E P L U G
Operation:
The model 5 and 6 OMEGA Bridge Plug is an economical, fully drillable bridge plug. The OMEGA 5 and 6 is suitable for well abandonments or zone suspension.
Characteristics:
in4-1/25-1/2
7
lbs/ft9.5-16.613-2317-35
in3.5004.3125.687
in3.8264.5806.000
in4.0905.0446.538
mm114.3139.7177.8
kg/m14.1-24.720.8-34.225.3-52
mm88.9
109.52144.45
mm97.18
116.33152.40
mm103.89128.12166.07
450DB5-00550DB5-00700DB5-00
Casing Size
Casing Weight
PlugO.D.
Setting Range
Min MaxProduct Number
www.TacticalCompletions.com | 1(800)239-90527
• Cost competitive• Constructed with drillable materials• Retaining rings assist in preventing element extrusion• Higher temperature of packing element available upon request• Sets in P-110 casing• 70 MPA (10,000 psi) rated• Temperature rating 150 degrees celsius or 300 degrees fahrenheit• Runs on existing wireline setting tool or hydraulic setting tools
OMEGA-10B R I D G E P L U G
Operation:
The O M E G A 10 model Bridge Plug is an economical, fully drillable bridge plug. For applications where a 70 mpa (10,000 psi) plug is sufficient. The OMEGA 10 is suitable for well abandonments or zone suspension.
Characteristics:
in2-3/82-7/83-1/2
44-1/2
55-1/25-3/46-5/8
77-5/88-5/8
lbs/ft4-5/8
6.4-6.55.7-10.35.6-14
9.5-16.615.5-20.8
13-2314-25.217-3217-3520-39
24-49
in1.7502.2202.7503.1403.5623.9374.3124.6995.3755.6876.3127.125
in1.7802.3402.8673.3403.8264.1544.5804.8905.5956.0006.6257.310
in2.0742.5253.2583.7324.0904.5605.0445.2906.1356.5387.1258.097
lbs13,00013,00013,00020,00033,00033,00033,00033,00050,00050,00050,00050,000
mm60.373.088.9101.6114.3127
139.7146
168.3177.8193.7219.1
kg/m5.95-8.69.5-9.7
8.6-15.38.3-20.8
14.1-24.717.1-31
20.8-34.2 20.8-37.525.3-4825.3-5229.8-58
35.7-72.9
mm44.4556.3969.8579.7690.47100.00109.52119.35136.531
44.45160.321
80.98
mm52.6864.1482.7594.79
103.89115.82128.12134.37155.83166.07180.98205.66
daN5,7825,7825,782
8,89614,67814,67814,67814,67822,24022,24022,24022,240
mm45.2159.4472.8284.8497.18
105.51116.33124.21142.11152.40168.20185.67
238DB10-00278DB10-00350DB10-00400DB10-00450DB10-00500DB10-00550DB10-00575DB10-00658DB10-00700DB10-00758DB10-00858DB10-00
Casing Size Casing Weight Plug O.D. Setting Range Setting Force Product
NumberMIN. MAX.
www.TacticalCompletions.com | 1(800)239-90528
• Sets in P110 casing• Constructed with drillable materials• Retaining rings to assist in preventing element extrusion• Higher temperature packing element available upon request• Temperature rating 150 degrees Celsius or 300 degrees Fahrenheit• Runs on existing wireline setting tool or hydraulic setting tools
OMEGA BIG BOYB R I D G E P L U G
Operation:
The OMEGA Big Boy Bridge Plug is an economical, fully drillable bridge plug and is suitable for well abandonments or zone suspension.
Characteristics:
in9-5/810-3/411-3/411-3/413-3/8
1620
lbs/ft29.3-58.432.7-60.7
38-6060-83
48-84.565-11894-133
in8.1259.43710.4379.93711.88014.12518.730
in8.3799.660
10.77210.19212.125
18.730
in9.063
10.19211.15010.772
15.25019.124
lbs50,00050,00050,00050,00050,00050,00050,000
mm244.5269.9298.5298.5339.7406.4508.0
kg/m43.6-86.948.7-90.356.5-89.3
89.3-123.571.4-125.796.7-175.5139.8-197.8
mm206.38239.70265.10252.40301.75358.78475.74
mm230.20258.88283.21273.61
387.35485.75
daN22,24022,24022,24022,24022,24022,24022,240
mm212.83245.36273.61258.88307.98
475.74
958DB-81075DB-51175DB-41176DB-41338DB-3
1600DB-1.52000DB-1.5
Casing Size Casing Weight Plug O.D. Setting Range Setting Force Product
NumberMIN. MAX.
OMEGA Big Boy 9-5/8”-20” Bridge Plug
www.TacticalCompletions.com | 1(800)239-90529
• Constructed with drillable materials• Retaining rings to assist in preventing element extrusion• Higher temperature of packing element available upon request• Sets in P-110 casing• 70 Mpa (10,000 psi) rated• Temperature rating 150 degrees Celsius or 300 degrees Fahrenheit• Right hand rotation to release work string
OMEGA-H2B R I D G E P L U G
Operation:
The O M E G A H2 Bridge Plug is designed to set with a combination of hydraulic pressure and mechanical pull.
Used for temporary or permanent zone and well abandonments.
Charcteristics:
OMEGA H2 Hydraulic Mechanical Bridge Plug Specification Guide
in3-1/2
44-1/2
55-1/25-3/46-5/8
77-5/88-5/89-5/8
10-3/413-3/8
lbs/ft5.7-10.35.6-14
9.5-16.611.5-20.8
13-2314-25.217-3217-3520-3924-49
29.3-58.432.7-60.748-84.5
in2.7503.1903.5623.9374.3124.6995.3755.6876.3127.1258.1759.437
11.880
in2.8673.3403.8264.1544.5804.8905.5956.0006.6257.3108.3799.660
12.175
in3.2583.7324.0904.5605.0445.2906.1356.5387.1258.0979.06310.19212.715
lbs1,5001,5001,5001,5001,5001,5001,5001,5001,5001,5001,5001,5001,500
lbs10,00017,00028,00028,00028,00030,00045,00045,00045,00045,00045,00045,00045,000
lbs13,00020,00030,00030,00030,00033,00050,00050,00050,00050,00050,00050,00050,000
mm88.9
101.6114.3127
139.7146.1168.3177.8193.7219.1244.5273.1339.7
kg/m8.6-15.38.3-20.814.1-24.717.1-31.019.3-34.220.8-37.525.3-47.6 25.3-52.129.8-58.035.7-72.943.6-86.948.6-90.371.4-125.7
mm69.8581.0390.47100.0109.52119.35136.53144.45160.32180.98207.65239.70301.75
mm82.7594.79
103.89115.82128.12134.37155.83166.07180.98205.66230.20258.88322.96
daN10.310.310.310.310.310.310.310.310.310.310.310.310.3
DaN44487566
12,45412,45413.34420,01620,01620,01620,01620,01620,01620,01620,016
DaN57828896
13,34413,34413,34414,67822,24022,24022,24022,24022,24022,24022,240
mm72.8284.8497.18
105.51116.33124.21142.11152.40168.28185.67212.83245.36309.25
350HM2-10400HM2-10450HM2-10500HM2-10550HM2-10575HM2-10658HM2-10700HM2-10758HM2-10858HM2-10958HM2-81075HM2-51338HM2-3
Casing Size Casing Weight Plug O.D. Setting Range SurfacePressure
Minimum Pull Force
MaximumPull Force Product
NumberMIN. MAX.
www.TacticalCompletions.com | 1(800)239-905210
• Wireline or Mechanical Set - can be set with electrical pressuresetting tool or mechanically on tubing.
• Speed and Safety - lock together design and extra clearance OD
• Slide Valve - controlled from surface by picking up work stringto close and setting down to open.
• Locked in Squeeze Pressure - the valve automatically closeswhen the stinger is removed locking in squeeze pressure whileexcess cement is circulated out.
• Isolates Hydrostatic Pressure - the valve protects sensitive zone inlow fluid level wells.
• 70 Mpa (10,000 psi) rated.
OMEGA CRC E M E N T R E T A I N E R
Operation:
The OMEGA Cement Retainer is an economical, fully drillable cement retainer. It easily converts from a wireline set to mechanical set with minimal changes. This provides the user with reliable high pressure plugging devices.
Application:
The CR Cement Retainer is designed for deep, hot, high risk, prolonged or complicated squeeze cement jobs.
Characteristics:
www.TacticalCompletions.com | 1(800)239-905211
in4-1/2
55-1/25-3/46-5/8
77-5/88-5/89-5/810-3/411-3/410-3/413-3/8
31620
lbs/ft9.5-15.111.5-20.8
13-2314-25.217-3217-3528-3924-49
29.3-58.432.8-60.7
38-6060-83
48-80.765-11894-113
in3.9533.9374.3124.70005.3755.6886.3127.1258.1259.43710.4379.93711,87514.12518.375
in3.8264.1564.5804.8905.5956.0046.6257.5118.4359.66010.77210.19212.175
18.730
in4.0904.5605.0445.2906.1356.5387.1258.0979.06310.19211.15010.77212.71515.25019.124
mm114.3127
139.7146
168.3177.8193.7219.1244.5273
298.5298.5339.7406.4508
kg/m14.1-22.517.1-31.019.3-34.220.8-37.525.3-47.625.3-52.029.8-58.0 35.7-72.943.6-86.948.7-90.356.5-89.389.3-123.571.4-120.097.6-175.5139.8-197.8
mm91.26100
109.52119.38136.53144.48160.32180.98206.38239.70265.10252.40301.63358.78466.73
mm103.89115.82128.12134.37155.83166.07180.98206.66230.20258.88283.21273.61322.96387.35485.75
mm97.18105.56116.33124.21142.11152.50168.28190.78214.25245.36273.61258.88309.25
475.74
Casing Size Casing Weight Retainer O.D. Setting RangeMIN. MAX.
OMEGA CR Cement Retainer Specification Guide
www.TacticalCompletions.com | 1(800)239-905212
• Allows high pressure tube testing.• Multiple safety release (rotate and shear out).• Gives positive indication of stinger location.
Mechanical J-Latch Stinger
Operation:
The mechanical J-Latch is a positive latch for operating the sliding valve inside a cement retainer. This provides positive control of the sliding valve during stage cementing operations.
Characteristics:
in4-1/25-1/2
7
in2-3/82-7/82-7/8
mm114.3139.7177.8
mm60.373.073.0
CasingSize
Tubing Size
www.TacticalCompletions.com | 1(800)239-905213
"MST" Mechanical Sett ing Tool
Operation:
The MST is designed to run and set the Polar Cement Retainers in tubing. In addition to the setting function the Retainer Mechanical Setting Tool will operate the retainer sleeve valve once the retainer is set.
Running the MST / Retainer combination assembly at a moderate rate of speed while preventing right-hand rotation will transmit to the setting tool. It is recommended that the tubing be rotated left every 10 stands until positive resistance is felt.
When the desired setting depth has been reached pull the assembly two feet above the desired setting point. Rotate the tubing to the right sufficiently to transmit 10 turns to the setting assembly.
Lower the setting assembly downward to the desired setting point. Proceed to pull the recommended tension above string weight, setting the slips and creating a pack off (as recommended in the setting chart below).
Slack off the equivalent amount of weight onto the assembly and again apply recommended tension. The retainer is now set and pressure testing may be performed. The setting tool may be released from the cement retainer by pulling 500 lbs. tension over the string weight and rotating the tubing 10 turns right. The setting tool may be re latched to the cement retainer by slacking off 1,000 lbs. string weight and snapped out by applying 5,000 lbs. of tension. The snap out forces will decrease after repeated usage and will stabilize at 2,508 lbs.
The tension sleeve valve is opened with downward motion (COMPRESSION) and closed with upward motion (TENSION). Two inches of travel from closed to open position.
in4-1/25-1/2
7
in2-3/82-7/82-7/8
mm114.3139.7177.8
mm60.373.073.0
CasingSize
Tubing Size
www.TacticalCompletions.com | 1(800)239-905214