7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 1/52
Weather Gard®
Product Guide
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 2/52
Weather Gard® Table of Contents
Section Page
Self-Drilling Fasteners
Impax™ Performance Drill Screws .................1
Impax™ Heavy Metal ThicknessStructural Drill Screws .................................2
Impax™ Sealer Drill Screws .............................3
Impax™ 1/4" Drill Screws ..............................4–5
Impax™ Insulated Panel Drill Screws .............6
irius® Drive Self-Drill
irius® Performance Drill Screws .................7–8
SX Stainless Self-Drill
SX Stainless Self-Drill ................................9–10
irius® SX Stainless Self-Drill .................... 11–12
Alloy Capped Fasteners
Zac
®
Impax
™
5/16" HWH Alloy Capped .......13Zac® Impax™ 3/8" HWH Alloy Capped
(for metal to metal) ...............................14–15
Zac® Impax™ 3/8" HWH Alloy Capped(for metal to metal and insulatedpanel to metal) .............................................16
Mac™ Impax™ Stainless Capped Self-Drill ...17
Zac® Tapping Fasteners .................................18
Prisma™ .............................................................19
Metal to Wood
Woodgrip™ Fasteners ...............................20–21
EVERGRIP™ Stainless Fasteners ...................22
Stainless Aluminum Panel Woodgrip™ .......23
Woodgrip™ Capped Fasteners ................24–25
Woodgrip™ #14 Milled Point ..........................26
Section Page
Self-Tapping Fasteners
Carbon Steel – Type A, AB, B .................27–28
Stainless Steel – Type A, AB, B .............29–30
#14 Milled Point – Type A ..............................31
Confas™ Concrete Fasteners .........................32
Panel Clips and Fasteners
Standing Seam Clips ............................... 33–34
Clip Fasteners ........................................... 35–36
WG-7™ Closure and Venting Products
WG-7™ Closure .................................................37
Pipe Flashing ....................................................38
ProfileVent® ......................................................39
Ventco™ Ridge Cap Anchor Clip ...................40
Tools, Belted Fasteners and Accessories
Installation Screw Guns .................................41
Panelmaster™ Belted Fasteners ....................42
Blind Rivets/Grommet Fasteners .................43
General Information
Fastener Design ........................................ 44–45
Washer and Fastener Head Styles ...............46
Structural Performance ..................................47
Coatings ............................................................48
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 3/52
Weather Gard® Self-Drilling Fasteners
Impax™— Performance Self-Drill 12-14 Impax and 1/4-14 Impax lap self-drilFor metal to meta
1SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0101-0907 ©2008 SFS intec, Inc.
• Precision cold forged assuring superior point strengthand the fastest drilling time performance through highstrength steel and nested purlins.
• Ultimate performance in light, mediumand heavy gage applications.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
• Mechanical zinc plated and coated with Silver Sentri™ for extended corrosion resistance.
Application
12-14 ImpaxMetal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
1/4-14 Impax LapPanel to panel side lapDrilling capacity: .030 – .095
Some applications may requireattaching light gage (24 – 26 ga)
to sub-structural member.Composite thicknessshould not exceed .095.
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection Part No. Part No. Part No. Part No.Length #12 Bond Seal (15 mm) #12 No Washer 1/4-14 Impax Lap w/ Bond Seal 1/4-14 Lap No Washer
12-14 x 3/4 " SD3 A2361-EDF A2361F — —
12-14 x 3/4" SD2 S449 5-EDF S4495F — —
12-14 x 1" SD2 S4577-EDF S4577F — —
12-14 x 1-1/4" SD2 S46 32-EDF S46 32F — —
12-14 x 1-1/2" SD2 S4677-EDF S46 77F — —
12-14 x 2" SD2 S477 7-EDF S4777F — —
12-14 2-1/2" SD2 S4902-EDF S4902F — —12-14 x 3" SD2 S4952-EDF S4952F — —
12-14 x 4" SD2 S4981-EDF S4981F — —
1/4-14 x 7/8 " — — S5051-GUF S5051F
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.):- 22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
5/16" AF Hex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.): Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.): SD2 SD3 12 ga (.109) : 1539 148014 ga (.075) : 1010 82316 ga (.060 ): 724 624
Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 124924 ga (.024): 1056
26 ga (.018): 654
OptionsSentri ™ Painted irius
ZAC®
MAC ™
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 4/52
Impax™ — Heavy Metal Thickness —Structural Drill Screws
12-24 Impax 4.5 and 5 self-drilFor metal to meta
Weather Gard® Self-Drilling Fasteners
2SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0102-0907 ©2008 SFS intec, Inc.
Application
12-24 Impax 4.5Metal to metalDrilling capacity: .075 – .375
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Thread length:12-24 x 1-1/4": .650
Min projection: 3/16" of threadsbelow substrate
12-24 Impax 5Metal to metalDrilling capacity: .075 – .500
Thickness is based on normal,single thickness purlin/girt ormultiple material thickness.
Thread length:12-24 x 1-1/4": .52012-24 x 1-1/2": .77012-24 x 2": 1.020
Min projection: 3/16" of threads
below substrate
NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listedare the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection Part No. Part No.Length Bond Seal (15 mm) No Washer
Impax 4.5
12-24 x 1-1/4" S4661-EDF S4661F
Impax 5
12-24 x 1-1/4" S466 8-EDF S466 8F
12-24 x 1-1/2" S4741-EDF S4741F
12-24 x 2" A2841-EDF A2841F
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
• Precision cold forged assuring superior point strengthand the fastest drilling time performance through highstrength steel and nested purlins.
• Delivers ultimate performance in mediumand heavy gage applications.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
• Zinc plated and coated with Silver Sentri™ for extendedcorrosion resistance.
5/16" AF Hex Washer HeadThread Major Dia: .216 – .210Thread Minor Dia: .186 – .181
Strength (lbs ult.):Tensile: 3450Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): E xceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over with Bond Seal (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584
5/16" AF Hex Washer HeadThread Major Dia: .216 – .210Thread Minor Dia: .186 – .181
Strength (lbs ult.):Tensile: 3450Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): E xceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over with Bond Seal (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584
OptionsSentri ™ Painted irius
ZAC®
MAC ™
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 5/52
Weather Gard® Self-Drilling Fasteners
Impax™— Sealer — Drill Screws 12-14 Impax sealer and 1/4-14 lap sealer self-drilFor metal to meta
3SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0103-0907 ©2008 SFS intec, Inc.
• Integral cupped Hex Washer Head configuration fastenerwith an EPDM sealing washer instead of the traditionalbonded sealing washer.
• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength
steel and nested purlins.
• Delivers ultimate performance in light, mediumand heavy gage applications.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
• Zinc plated and coated with Silver Sentri™ for extended
corrosion resistance.
Application
12-14 Sealer ImpaxMetal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
1/4-14 Sealer Impax LapPanel to panel side lapfrom .030 – .095Some applications may requireattaching light gage (24 – 26 ga)
to sub-structural member. Composite thickness should not exceed .095
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection Part No. Part No.Length #12 Sealer 1/4-14 Sealer Lap
12-14 x 3/4" S448 6-FGF —
12-14 x 1" S4611-FGF —
12-14 x 1-1/4" X4636-FGF —
12-14 x 1-1/2" X4721-FGF —
1/4-14 x 7/8" — S5076-FF F
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Cupped Hex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.):12 ga (.105): 153914 ga (.075): 101016 ga (.060): 724
Pull-over (lbs ult.):
22 ga (.030): 129824 ga (.024) : 110226 ga (.018): 692
5/16 Cupped Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.):22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
OptionsSentri ™ Painted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 6/52
Weather Gard® Self-Drilling Fasteners
Impax™— 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drilFor metal to meta
4SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0104-0907 ©2008 SFS intec, Inc.
• Precision cold forged assuring superior point strengthand the fastest drilling time performance through highstrength steel and nested purlins.
• Impax #2 point is designed with a reduced drill point diameter to provide higher pullout in single purlin attachment.
• Delivers ultimate performance in mediumand heavy gage applications.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
• Zinc plated and coated with Silver Sentri™
for extended corrosion resistance.
Application
1/4-14 Impax HWH #2 Point and #3 PointMetal to metalDrilling capacity:
#2 point: .050 – .150 #3 point: .050 – .210
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
1/4-20 Impax HWH #4 PointMetal to metalDrilling capacity:
.060 – .250
Thickness is based on normal,
single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listedare the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
#2 – 5/16 AF Hex Washer Head #3 – 3/8" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850
#2 Point Pull-out (lbs ult.):12 ga (.105): 208814 ga (.075): 131216 ga (.060): 903
#3 Point Pull-out (lbs ult.):12 ga (.105): 169714 ga (.075): 115116 ga (.060): 687
Pull-over with Bond Seal (lbs ult.):22 ga (.030): 107924 ga (.024) : 88426 ga (.018): 616
3/8" AF Hex Washer HeadThread Major Dia: .250 – .241Thread Minor Dia: .200 – .184
Strength (lbs ult.):Tensile: 4200Torsional: 156 in-lbsShear: 2920
Pull-out (lbs ult.):
12 ga (.030): 191314 ga (.024): 106116 ga (.018): 707
Pull-over with Bond Seal (lbs ult.):22 ga (.030): 111724 ga (.024) : 98826 ga (.018): 629
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 7/52
Weather Gard® Self-Drilling Fasteners
5SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0104-0907 ©2008 SFS intec, Inc.
Impax™— 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drilFor metal to meta
Selection Part No. Part No. Part No. Part No. Part No. Part No. #3 & #4 Point #3 & #4 Point #2 Point Bond Seal #2 Point No Washer #2 Point Bond Seal #2 Point No WasherLength Bond Seal No Washer 5/16" HWH 5/16" HWH 3/8" HWH 3/8" HWH
1/4-14 x 3/4" S5010-GBF S5010F — — — —1/4-14 x 1" S5155-GBF S5155F — — S5171-GBF S5171F
1/4-14 x 1-1/4" S5201-GBF S5201F S5191-GBF S5191F — —
1/4-14 x 1-1/2" S5251-GBF S5251F S5286-GBF S5286F S5271-GBF S5271F
1/4-14 x 2" S5351-GBF S5351F — — — —
1/4-14 x 2-1/2" S5381-GBF S5381F — — — —
1/4-14 x 3" S5451-GBF S5451F — — — —
1/4-20 x 4" #4 Point S5621-GBF S5621F — — — —
1/4-20 x 5" #4 Point S5641-GB S5641 — — — —
1/4-20 x 6" #4 Point S5661-GB S5661 — — — —
1/4-20 x 7" #4 Point S5671-GB S5671 — — — —
1/4-20 x 8" #4 Point S5681-GB S5681 — — — —
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
OptionsSentri ™ Painted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 8/52
Impax™— Insulated Panel Drill Screws Insulation fastenersFor metal to meta
6SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0105-0907 ©2008 SFS intec, Inc.
Weather Gard® Self-Drilling Fasteners
• Designed for a particular thickness of insulated panel to insure uniform attachment without overdriving anddimpling the panel surface.
• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength
steel and nested purlins.
• Delivers ultimate performance in light, mediumand heavy gage applications.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
Application
12–14 InsulatedPanel FastenerDesigned for use in attachinginsulated foam panels to steelDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threads
below substrate
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners.
SelectionLength Insulated Panel Thickness Part No.
12-14 x 1-7/8" 3/4 " to 1" S7041-GBF
12-14 x 2-3/8" 1-1/8" to 1-1/2" S7061-GBF
12-14 x 3-1/4" 1-5/8" to 2-3/8" S7081-GBF
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Hex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult):Tensile: 2900Torsional 92 in-lbsShear: 2050
Pull-out (lbs ult.):12 ga (.105): 153914 ga (.075): 101016 ga (.060): 724
Pull-over with Bond Seal (lbs ult.):
22 ga (.030) : 114824 ga (.024): 105626 ga (.018): 654
OptionsSentri ™ Painted ZAC®
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 9/52
Weather Gard® irius® Drive Self-Dril
irius® Performance Drill Screws irius 12-14, 12-24 self-drill and 1/4-14 lap self-drillFor metal to meta
7SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0201-0907 ©2008 SFS intec, Inc.
• irius is a patented drive system adaptable to a full rangeof metal building fasteners.
• irius fasteners’ low profile head has changed the futurearchitectural appearance of side-wall fastening.
Applicatio
• Fastening system drive socket ensures positive engagementand prevents damage to a painted fastener head.
• Impax™ or SX self-drilling point design assures superiorpoint strength and excellent drill performance throughhigh strength steel.
irius low profile and drive system Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.): 22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
Application12-14 irius Self-DrillMetal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
1/4-14 irius LapPanel to panel side lapDrilling capacity: .030 – .095
Some applications may requireattaching light gage (24 – 26 ga)
to sub-structural member.Composite thickness should notexceed .095 thickness.
12-24 irius 5
Metal to metalDrilling capacity: .075 – .550
Thickness is based on normal,single thickness purlin/girt ormultiple material thickness.
Thread length: 12-24 x 1-1/2": .770
Min projection: 3/16" of threadsbelow substrate
Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled s teel material. Lap self-drill pull-out valuesis based on 40,0 00 psi AZ 55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered
and appropriate safety factors applied when specifying the proper fasteners. .
irius low profile and drive systemThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.): 12 ga (.105): 153914 ga (.075): 101016 ga (.060): 724
Pull-over with Bond Seal (lbs ult.): 24 ga (.024): 93426 ga (.018): 585
irius low profile and drive systemThread Major Dia: .216 – .208
Thread Minor Dia: .174 – .161Strength (lbs ult.): Tensile: 3450Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.): 12 ga (.105): 19543/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over with Bond Seal (lbs ult.): 24 ga (.024): 84426 ga (.018): 511
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 10/52
Weather Gard® irius® Drive Self-Dril
irius® Performance Drill Screws irius 12-14, 12-24 self-drill and 1/4-14 lap self-drillFor metal to meta
8SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0201-0907 ©2008 SFS intec, Inc.
Selection Part No. Part No. Part No. #12-14 Bond Seal 1/4-14 Lap 12-24 5.0Length 7/16 (12 mm) Length Bond Seal Bond Seal
12-14 x 1-1/4" S6632-F YF 1/4-14 x 7/8" S6851-HZF —12-14 x 1-1/2" S6677-FYF 12-24 x 1-1/2 (5) — S6741-FYF
12-14 x 2" S6777-FYF
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
OptioOptionsSentri ™ Painted
SX StainlessSelf-Drilling
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 11/52
Weather Gard® SX Stainless Self-Dril
SX Stainless Self-Drill SX austenitic stainless steeFor metal to meta
9SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0301-0508 ©2008 SFS intec, Inc.
Application
SX 3-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity : .047 – .118
SX 6-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .079 – .236
SX 14-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550
SX L2-Free Spin LapSelf-Drill5/8" O.D Bond SealMetal to metalDrill capacity: .031 – .079
5/16" AF Hex Washer HeadDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Pull-out (lbs ult.):12 ga (.105): 97014 ga (.075): 65016 ga (.060): 590
Pull-over (lbs ult.):24 ga (.024) : 119026 ga (.018): 665
5/16" AF Hex Washer HeadDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Pull-out (lbs ult.):12 ga (.105): 112514 ga (.075): 85516 ga (.060 ): 610
Pull-over (lbs ult.):
24 ga (.024): 130026 ga (.018): 705
5/16" AF Hex Washer HeadDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Pull-out (lbs ult.):12 ga (.105): 12203/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over (lbs ult.):24 ga (.024) : 115026 ga (.018): 646
5/16" AF Hex Washer HeadDia: Nominal #14
Strength (lbs ult.):Tensile: 3600Torsional: 70 in-lbsShear: 360 0
5/16" AF Hex Washer HeadDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
• SX Austenitic stainless fasteners come with either a carbon steelspade point or the Bi-metal welded carbon steel point.
• SX Austenitic stainless product line offers fastening solutionsfor attaching panels from very thin to over 1/2" structural steel.
• Provides ultimate corrosion performance for attaching steel,
stainless or aluminum panels.• Designed for secured attachment to both panel and substructures.
• Stainless self-drill fasteners are engineered to havelow driving torque and provide maximum clamp load.
• Ultimate drill performance in light, medium, andheavy gage applications.
• Washer O.D designed for both sidewall and roof
panel attachment.
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 12/52
SX Stainless Self-Drill SX austenitic stainless steeFor metal to meta
Weather Gard® SX Stainless Self-Dril
10SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0301-0508 ©2008 SFS intec, Inc.
Application continued
SX C-Self-Drill3/4" O.D Stainless Bond Seal
Insulated panel to metalDrill capacity : .157 – .551
SXCW-Self-Drill3/4" O.D Stainless Bond SealInsulated panel to wood
Drill capacity: .031 – .079
Selection U. S. Measurement Article No.
SX 3-Self-Drill
SX3/4-S16-5.5x22 #12-11 x 7/8" 0003356
SX3/10-S16-5.5x28 #12-11 x 1-1/8" 0003358
SX3/15-S16-5.5x38 #12-11 x 1-1/2" 0003 360
SX3/26-S16-5.5x50 #12-11 x 2" 0740424
SX3/20-34-S16-5.5x52 #12-11 x 2-1/8" 0003 363
SX3/20-44-S16-5.5x65 #12-11 x 2-1/2" 0027817
SX3/20-55-S16-5.5x75 #12-11 x 3" 0053144
SX 6-Self-Drill
SX6/6-S16-5.5x26 #12-14 x 1" 0003357
SX6/12-S16-5.5x32 #12-14 x 1-1/4" 0003359
SX6/15-S16-5.5x38 #12-14 x 1-1/2" 0003 364
SX 14-Self-Drill
SX14/12-S16-5.5x40 #12-14 x 1-1/2" 0770785
SX L2-Free Spin Lap Self-Drill
SXL2-S14-5.5x22 #12-11 x 7/8" 0003385
SXL2-S16-6.3x25 #14-14 x 1" 0003 369
InstallationTools: 0 – 2000 rpm screwdriver equippedwith depth sensing nosepiece.
5/16" AF Hex Washer HeadThread Major Dia: .213 – .207
Strength (lbs ult.):Tensile: 3150Torsional: 92 in-lbsShear: 2700
5/16" AF Hex Washer HeadThread Major Dia: .255 – .249
Strength (lbs ult.):Tensile: 3732Torsional: 95 in-lbs
Shear: 2855
U. S. Measurement Article No. Panel Thickness
SX C-Self-Drill
SXC14-S19-5.5 x 80 #12-14 x 3-1/8" 0773620 1-1/2" – 2-1/16"
SXC14-S19-5.5 x 99 #12-14 x 3-3/4" 0775732 1-7/8" – 2-7/16"
SXC14-S19-5.5 x 118 #12-14 x 4-5/8 " 0776324 2-7/16" – 3-3/ 8"
SXC14-S19-5.5 x 138 #12-14 x 5-1/2" 07684 91 3-3/16" – 4"
SXC14-S19-5.5 x 168 #12-14 x 6-5/8 " 075788 0 3-15/16" – 5-7/32"
SXCW-Self-Drill
SXCW-S19-6.5 x 90 #14 x 3-1/2" 0998230 1-1/8" – 1-1/2"
SXCW-S19-6.5 x 105 #14 x 4-1/8" 09978 36 1-1/2" – 2"
SXCW-S19-6 .5 x 115 #14 x 4-9 /16" 099 8241 1-7/8" – 2-7/16"
SXCW-S19-6.5 x 135 #14 x 5-3/8 " 0997821 2-11/16" – 3-1/4"
SXCW-S19-6.5 x 155 #14 x 6-1/4" 09978 40 3-9/3 2" – 4"
OptionsPainted irius
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 13/52
Weather Gard® SX Stainless Self-Dril
irius® SX Stainless Self-Drill irius SX austenitic stainless steeFor metal to meta
11SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0302-0508 ©2008 SFS intec, Inc.
• irius is a patented drive system available on a full rangeof metal building fasteners.
• irius SX stainless fasteners’ low profile head that has changed the future architectural appearance of sidewall fastening.
• Fastening system drive socket insures positive engagement
and prevents damage to a painted fastener head.
• Self-drilling point design assures superior point strength and the excellent drill performance through high strength steel.
• Stainless fasteners provide the ultimate corrosionperformance for attaching steel, stainless or aluminum panels.
• SX austenitic stainless self-drill fasteners are engineered to
have low driving torque and provide maximum clamp load.
Application
SX 3-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity : .047 – .118
SX 6-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity: .079 – .236
SX 14-L12 irius Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550
SX L2-L12 irius Free SpinLap Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .031 – .079
irius low profile and drive systemDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Pull-out (lbs ult.):12 ga (.105): 112514 ga (.075): 85516 ga (.060 ): 610
Pull-over (lbs ult.):24 ga (.024): 1300
26 ga (.018): 705
irius low profile and drive systemDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Pull-out (lbs ult.):12 ga (.105): 97014 ga (.075): 65016 ga (.060): 590
Pull-over (lbs ult.):24 ga (.024): 119026 ga (.018): 665
irius low profile and drive system
Dia: Nominal #12Strength (lbs ult.):Tensile: 4050Torsional: 70 in-lbsShear: 2700
Pull-out (lbs ult.):12 ga (.105): 122014 ga (.075): 718
Pull-over (lbs ult.):24 ga (.024): 115026 ga (.018): 646
irius low profile and drive systemDia: Nominal #12
Strength (lbs ult.):Tensile: 3150Torsional: 70 in-lbsShear: 2140
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 14/52
irius® SX Stainless Self-Drill irius SX austenitic stainless steeFor metal to meta
Weather Gard® SX Stainless Self-Dril
12SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0302-0508 ©2008 SFS intec, Inc.
Selection U. S. Measurement Article No.
SX 3-L12 irius Self-Drill
SX3/4-L12-A12-5.5x22 #12-11 x 7/8" 0996726SX3/10-L12-A12-5.5x28 #12-11 x 1-1/8" 0996727
SX3/15-L12-A12-5.5x38 #12-11 x 1-1/2" 0996680
SX 6-L12 irius Self-Drill
SX6/6-L12-A12-5.5x26 #12-14 x 1" 0996719
SX6/12-L12-A12-5.5x32 #12-14 x 1-1/4" 0996720
SX 14-L12 irius Self-Drill
SX14/12-L12-S16-5.5x38 #12-14 x 1-1/2" 0776328
SX L2-L12 irius Free Spin Lap Self-Drill
SXL2-L12-S14-5.5x22 #12-11 x 7/8" 0945591
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 15/52
Weather Gard® Alloy Capped Fasteners
ZAC® Impax™—5/16" HWH Alloy Capped
ZAC 5/16" HWHZinc aluminum capped drill screws
For metal to meta
13SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0401-0508 ©2008 SFS intec, Inc.
• ZAC: the most widely used zinc aluminum cappedfastener in the industry.
• Precision cold forged assuring superior point strengthand the fastest drilling time performance through highstrength steel and nested purlins.
• Integral cupped Hex Washer Head can never red rust.• Designed and engineered to have low driving and thread
engagement torque while providing maximum clamp load.
Application
12-14 ZAC (5/16")Metal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
1/4-14 ZAC Lap (5/16")Panel to panel side lapDrilling capacity: .030 – .095
Some applications may requireattaching light gage (24 – 26 ga)
to sub-structural member.Composite thickness should notexceed .095 thickness.
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values arebased on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing and we believe typical. The specific job conditions should beconsidered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nestedpurlins.
SelectionPart No. Part No.
Length 12-14 ZAC 1/4-14 ZAC Lap
5/16" AF Hex Washer Head ZAC
12-14 x 1" S4591-FLF
12-14 x 1-1/4" X4646-FLF —
12-14 x 1-1/2" X4731-FLF —
12-14 x 2" S4761-FLF —1/4-14 x 7/8" — S5031-FMF
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.): 12 ga (.105): 153914 ga (.075): 101016 ga (.060 ): 724
Pull-over (lbs ult.): 22 ga (.030): 164724 ga (.024): 131026 ga (.018): 794
5/16" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.): 22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 16/52
ZAC® Impax™—3/8" HWH Alloy Capped
ZAC self-drill 3/8" HWHZinc aluminum capped drill screws
For metal to meta
Weather Gard® Alloy Capped Fasteners
14SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0402-09 07 ©2008 SFS intec, Inc.
• ZAC: the most widely used zinc aluminum capped fastenerin the industry.
• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strengthsteel and nested purlins.
• Designed and engineered to have low driving and threadengagement torque to prevent damage to the cap duringinstallation while providing maximum clamp load.
• Integral cupped Hex Washer Head can never red rust.
Application
12-14 ZAC (3/8")Metal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt or multiplematerial thickness combined for total.
Min projection: 3/16" of threadsbelow substrate.
1/4-14 ZAC Lap (3/8")Panel to panel side lapDrilling capacity: .030 – .095
Some applications may requireattaching light gage (24 – 26 ga) tosub-structural member. Composite
thickness should not exceed.095 thickness.
12-14 x 3/4 ZAC Lap (3/8" )Sharp pointPanel to panelDrilling capacity .030 – .060
Self-piercing points are not designedfor attaching light gage (24 – 26 ga)
to sub-structural member.
NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
3/8" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.):12 ga (.105): 153914 ga (.075): 101016 ga (.060 ): 724
Pull-over (lbs ult.):22 ga (.030): 1647
24 ga (.024): 131026 ga (.018): 794
3/8" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.):22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
3/8" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .215 – .208Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2100Torsional: 92 in-lbsShear: 1800
Pull-out (lbs ult.)22 ga (.030): 53824 ga (.024) : 43026 ga (.018): 330
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 17/52
Weather Gard® Alloy Capped Fasteners
ZAC® Impax™—3/8" HWH Alloy Capped
ZAC self-drill 3/8" HWHZinc aluminum capped drill screws
For metal to meta
15SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0402-09 07 ©2008 SFS intec, Inc.
Selection Part No. Part No..Length 12-14 1/4-14 Lap)
3/8" Hex Washer Head ZAC
12-14 x 3/4 " A1653-FLF Sharp Point LAP —
12-14 x 1" S4576-FLF —
12-14 x 1-1/4" S46 31-FLF —
12-14 x 1-1/2" S46 76-FLF —
12-14 x 2" S4776-FLF —
12-14 x 2-1/2" S49 01-FLF —
12-14 x 3" S4951-FLF —
1/4-14 x 7/8" — S5065-FMF
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 18/52
ZAC® Impax™
3/8" HWH Alloy Capped
ZAC® self-drill 3/8" HWHZinc aluminum capped drill screws
For metal to metal and insulated panel to metal
Weather Gard® Alloy Capped Fasteners
16SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0403-0 907 ©2008 SFS intec, Inc.
• ZAC: the most widely used zinc aluminum capped fastenerin the industry.
• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strengthsteel and nested purlins.
• Designed and engineered to have low driving and threadengagement torque to prevent damage to the cap duringinstallation while providing maximum clamp load.
• Integral cupped Hex Washer Head can never red rust.
Application
12-24 ZAC (3/8")4.5 point and 5 pointMetal to metalImpax 4.5Drilling capacity: .075 – .375
Impax 5Drilling capacity: .075 – .500
Thickness is based on single thickness purlin/girt or multiplematerial thickness combined for total.
Thread length:
ZAC 4.5: 12-24 x 1-1/4": .650 ZAC 5: 12-24 x 1-1/4": .52012-24 x 1-1/2": .770
12-24 x 2" : 1.020
Min projection: 3/16" of threadsbelow substrate
12-14 InsulatedPanel FastenerDesigned for attachinginsulated foam panels to steel.Drilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girt or
multiple material thicknesscombined for total.
Min projection: 3/16" of threadsbelow substrate
Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection Part No. Part No. PanelLength 12-14 Insulated 12-24 (4.5 ) and 12-24 (5) Thickness
12-24 x 1-1/4" (4.5) — S4665-FLF —
12-24 x 1-1/4" (5) — S4669-FLF —
12-24 x 1-1/2" (5) — S4742-FLF —
12-14 x 1-7/8" S7045-FMF 3/4" to 1"12-14 x 2-3/8" S7065-FMF 1-1/8" to 1-1/2"
12-14 x 3-1/4" S7085-FMF 1-5/8" to 2-3/8 "
InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
3/8" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .216 – .210Thread Minor Dia: .186 – .181
Strength (lbs ult.):Tensile: 3450Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over with assembledSeal washer (lbs ult.):
22 ga (.030): 164724 ga (.024): 131026 ga (.018): 794
3/8" AF Zinc Aluminum CappedThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.):12 ga (.105): 1539
14 ga (.075): 101016 ga (.060): 724
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 19/52
Weather Gard® Alloy Capped Fasteners
MAC™ Impax™ —Stainless Capped Self-Drill
MAC stainless capped drill screwsFor metal to meta
17SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0404- 0907 ©2008 SFS intec, Inc.
• MAC has a stainless capped, integral cupped Hex WasherHead configuration that can never red rust.
• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.
Application
12-14 MACAssembled with EPDM washerMetal to metalDrilling capacity: .035 – .210
Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total, as in overlappedor nested purlin construction.
Min projection: 3/16" of threadsbelow substrate
1/4-14 MAC LapAssembled with EPDM washerPanel to panel side lapDrilling capacity: .030 – .095
Some applications may requireattaching light gage (24 – 26 ga)
to sub-structural member.Composite thickness should notexceed .095 thickness.
12-24 MAC 4.5
Assembled with EPDM washerMetal to metalDrilling capacity: .075 – .375
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Nominal thread length:12-24 x 1-1/4": .650
Min projection: 3/16" of threadsbelow substrate
NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull out values are
based on 40,000 PSI AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection Part No. Part No. Part No.Length 12-14 MAC 1/4-14 MAC 12-24 MAC
12-14 x 1" S45 30-FAF — —
12-14 x 1-1/4" S4650-FAF — —
12-14 x 1-1/2" S4690-FAF — —
12-14 x 2" S4770-FAF — —
1/4-14 x 7/8" — S5100-GGF —
12-24 x 1-1/4" (4.5 ) — — S46 72-FAF
5/16” AF Stainless CappedHex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.):Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.):12 ga (.105): 153914 ga (.075): 101016 ga (.060): 724
Pull-over (lbs ult.):22 ga (.030): 129824 ga (.024) : 110226 ga (.018): 692
5/16” A F Stainless Capped HexWasher HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.):22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204
5/16” AF Stainless Capped Hex Washer HeadThread Major Dia: .216 – .210
Thread Minor Dia: .186 – .181Strength (lbs ult.):Tensile: 3450Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value
Pull-over (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584
InstallationTools: 0 – 2000 rpm screwdriver equipped with depthsensing nosepiece.
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 20/52
ZAC® Tapping FastenersZAC self-tapping fasteners
A and AB milled pointFor metal to meta
Weather Gard® Alloy Capped Fasteners
18SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0405-0 907 ©2008 SFS intec, Inc.
• Integral cupped Hex Washer Head configuration can never red rust.• Designed for attaching both metal to wood and metal to metal.
• Milled points do not require a pre-drilled hole whenattaching 26 and 24 gage metal to wood.
Application
1/4 -14 ZAC Type ABMilled PointMetal to woodMetal to metalSelf-Drilling Metal Thickness:Sheet .018 – .030
Thickness is based on normal,single or multiple material thicknesscombined for total
Min depth penetration into thewood sub structure: 1"
#17 Zac Type AB
Strip-out RepairMetal to metalRepair fastener for stripped out
#14 Type A or 1/4" AB
Min projection: 3/8" of threadsbelow substrate
NotesDimensions are nominal inches unless noted. When using Milled point fasteners for metal to metal see the tapping screw section for performance values. Pull-out values(pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate valueslisted are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection Part No. Part No.Length 1/4-14 AB Length #17 AB
3/8" ZAC
1" A4395-FMF 17 x 1" A6045-LFF
1-1/2" A4485-FMF 17 x 1-1/2" A6066-LFF
2" A4513-FMF
2-1/2" A4510-FMF
InstallationTools: 0 – 1800 or 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
3/8 AF Hex HeadThread Major Dia: .290 – .284
Thread Minor Dia: .220 – .214
3/8" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 150 in-lbsShear: 2850
Pull-out (lbs ult.): 22 ga (.030): 37924 ga (.024) : 30426 ga (.018): 204
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 21/52
Weather Gard® Capped Fasteners
Prisma™Nylon headed fasteners
self-tapping, self-drill and WoodgripFor metal to metal and metal to wood
19SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0406-0 907 ©2008 SFS intec, Inc.
• Prisma nylon head is absolutely corrosion proof.• Nylon head can withstand extreme installation torque without failure.
• Requires no special socket for installation.
• Special washer face allows the fastener to be usedon sidewall without a sealing washer.
• Nylon heads are available in 25 standard colors.
Application #14 Type ABMetal to metalSelf-Tapping AB:1/4-14 x 3/4"1/4-14 x 1-1/2"1/4-14 x 2"
Stainless AB:1/4-14 x 3/4"
Self-Drill:1/4-14 x 1"1/4-14 x 1-3/8"1/4-14 x 2"
Drill capacity: .050 – .210
1/4-14 x 7/8 LapMetal to metalPanel to panel side lapdrilling capacity: .030 – .095
Self-Drilling Metal Thickness:
Thickness is based on normal,single or multiple material thicknesscombined for total.
#10 WoodgripMetal to wood10 x 1"10 x 1-1/2"10 x 2"10 x 2-1/2"10 x 3"
Min depth penetration into thewood sub structure: 1"
NotesDimensions are nominal inches unless noted. For Type AB metal to metal, see tapping screw section for performance values.
OptionsNone
7/16" Nylon Hex Washer Head
1/4-14:Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 2560
1/4-14 AB Carbon Steel:
Pull-out (lbs ult.): 12 ga (.105): 218514 ga (.075): 127716 ga (.060): 879
1/4-14 #3 Point Carbon Steel:
Pull-out: (lbs ult.): 12 ga (.105): 169714 ga (.075): 115116 ga (.060): 687
7/16" Nylon Hex Washer Head
1/4-14:Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 2560
Woodgrip Prisma 3/8" Nylon Hex Washer Head
Thread Major Dia: .199 – .191Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs minShear: 933
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 22/52
Woodgrip™ Fasteners Woodgrip and HiLo WoodgripFor metal to wood
Weather Gard® Metal to Wood
20SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0501-0708 ©2008 SFS intec, Inc.
Application
Woodgrip 9–15 HWHSharp PointAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal panel
and taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
Woodgrip 9–15 HWHSharp PointMechanical Zinc-.001" minAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
HiLo Woodgrip 10 –15Assembled Bond Seal washerMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
Woodgrip XG 12– 8 HWHSharp PointAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal paneland taps into wood substrate. Large,aggressive thread design providessuperior resistance to strip-out, andsuperior performance in OSB, plywood,and 1x4" pine. Min penetration in woodsubstrates should be no less than 1"
NotesDimensions are nominal inches unless noted.
1/4" Hex Washer HeadThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933
1/4" Hex Washer HeadThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933
1/4" Hex Washer HeadThread Major Dia: .199 – .191Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933
1/4" Hex Washer HeadThread Major Dia: .219 – .215
Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 2183Torsional: 60 in-lbs min.Shear: 1946
Woodgrip is the original sheet to wood fastenerdesigned to self-drill metal panels:• High Hex Washer Head provides driving stability
and a sharp point for quick installation.• Assembled with a control seal washer for a consistent,
weather tight seal and improved installation appearance.• Zinc plated and Silver Sentri™ coated for corrosion protection.• Alternate mechanical zinc (.001" min thick) plus Silver Sentri™
coated offers increased corrosion protection
HiLo Woodgrip is a sheet to wood fastenerdesigned to self-drill metal panels:• High Hex Washer Head provides driving stability
and a sharp point for quick installation.• Assembled with a bond seal washer for a consistent, weather
tight seal and improved installation appearance.• Zinc plated and Silver Sentri coated for corrosion protection.
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 23/52
Weather Gard® Metal to Wood
Woodgrip™ Fasteners Woodgrip and HiLo WoodgripFor metal to wood
21SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0501-0708 ©2008 SFS intec, Inc.
Application
Woodgrip 12 x 3/4 LapAssembled Bond Seal washerDrilling capacity: 2 x 24 gaPanel to panel side lap, end lapand other sti tch applications
Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir
#9 Woodgrip Control Seal Washer
1-1/2" Penetration 748
1" Penetration 542
#10 Hi Lo Woodgrip Bond Seal Washer
1-1/2" Penetration 820
1" Penetration 524
% Increase Strip-outPull-out (lbs ult.) vs. Woodgrip (in-lbs)
#12 Woodgrip XG Control Seal Washer
SPF 1-1/2" Penetration 874 20
SPF 1" Penetration 571 20
1x4" Pine 590 34
3/4" Plywood 587 25
5/8" Plywood 446 31
1/2" Plywood 384 39
23/ 32" OSB 524 21
19/32" OSB 456 31
Notes: Woodgrip and HiLo pull-out strength values may vary from tested loads depending upon specific wooddensity variations. Woodgrip and HiLo pull-over strength values are based on .035" thick, 1/2" OD ControlSeal or Bond Seal washers, and have been updated to reflect common tensile strengths of metal panels asa function of panel thicknesses. Percent increase strip-out values of the Woodgrip XG over the standardWoodgrip are typical results, as encountered when fasteners are installed at 2500 rpm until full strip-outoccurs. Ultimate values listed are the result of laboratory testing. The specific job conditions should beconsidered, and appropriate safety factors applied, when specifying the proper fasteners.
SelectionSize Woodgrip HiLo Woodgrip Mechanical Zinc Woodgrip Woodgrip XG
1" C0161-CCF A1067-CDF C0167-CCF A1806-EMF1-1/2" C0261-CCF A1072-CDF C0267-CCF A1841-EMF
2" C0381-CCF A1077-CDF C0387-CCF A1851-EMF
2-1/2" C0461-CCF A1082-CDF C0467-CCF A1856-EMF
3" C0485-CCF A1087-CDF C0487-CCF A1861-EMF
12 x 3/4 " (1/4" HWH) A1701-ECF A1701-EAF – –
InstallationTools: 0 – 2500 rpm screw driver equipped withdepth sensing nose piece.
OptionsSentri ™
Color Sentri ™
COLOR
Painted ZAC®
ZAC
MAC ™
MAC
Pull-over
28 ga (110 ksi): 577
26 ga (70 ksi): 63724 ga (70 ksi): 800
28 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
1/4" Hex Washer Head:Thread Major Dia: .215 – .208Thread Minor Dia: .164 – .157
Strength (lbs ult.): Tensile: 2100Torsional: 92 in-lbs min.Shear: 1800
Pull-over
28 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
Fasteners installed in less than 1" of solid wood mayhave an increased potential for sealing or connectionfailure over time. This may be due to the fasteners beingstripped out during installation and/or due to the lackof adequate wood fiber material to hold the fastener inplace during thermal movement cycles or other forceswhich may be exerted upon the connection.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 24/52
EVERGRIP™ Stainless Fasteners EVERGRIP stainless bi-metaFor metal to wood
Weather Gard® Metal to Wood
22SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0502-0508 ©2008 SFS intec, Inc.
EVERGRIP stainless wood fastener is designed to self-drill metal panels:• Head and the majority of shank is 304 Stainless Steel, with a
welded, hardened carbon steel point for self-drilling performance.• Provides the corrosion protection of stainless with the drill
performance of a carbon steel fastener.
• Designed specifically for corrosion resistance in new wood treatments (ACQ/CA).
Application
EVERGRIP9 – 15 HWH Sharp PointAssembled withstainless Bond SealMetal to woodDrilling capacity: 24 ga (0.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substrates
should be no less than 1"
EVERGRIP9 – 15 T-25 (TORX®) Pan HeadAssembled withstainless Bond SealMetal to woodDrilling capacity: 24 ga. (0.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
Performance Pounds Ultimate Pull-out (lbs ult.)
Wood: Spruce, Pine, Fir
EVERGRIP Stainless Bond Seal
1-1/2" Penetration 748
1" Penetration 542
Notes: Dimensions are nominal inches unless noted. Pull out strength values mayvary from tabulated loads depending upon specific wood density variations.Pull over strength values are based on AZ55 Galvalume steel material.Ultimate values listed are the result of laboratory testing. The specific jobconditions should be considered and appropriate safety factors applied.
Selection HWH HWH T-25 Pan HeadLength 250/Bag 100/Box 250/ Bag
1" E4160-CUF E4160-CUEG 1119934
1-1/2" E4260-CUF E4260-CUEG 1124180
2" E4380-CUF E4380-CUEG 1119937
2-1/2" E4460-CUF E4460-CUEG —
3" — — 1119938
Description Part No. Quantity
SFS Special T-25 Torx drive bit 0514261 1 each
InstallationTools: 0 – 2500 rpm screwdriver equippedwith depth sensing nosepiece.
The EVERGRIP 9-15 T-25 (TORX) Pan Headrequires a T-25 Torx drive bit.
Utilizing the special SFS T-25 Torx drivebit manufactured by SFS intec isrecommended for superior stabilityduring the installation process.
OptionsPainted
1/4" Hex Washer HeadThread Major Dia: 0.181 – 0 .175Thread Minor Dia: 0.133 – 0.127
Strength (lbs ult.): Tensile: 1657Torsional: 50 in-lbs min.Shear: 1550
Pull-over
28 ga: 378
26 ga: 519
24 ga: 704
T-25 (TORX ) Pan HeadHead Dia: 0.393 –0.374”Thread Major Dia: 0.181 – 0 .175Thread Minor Dia: 0.133 – 0.127
Strength (lbs ult.): Tensile: 1657Torsional: 50 in-lbs min.Shear: 1550
Utilizing the special SFS T-25 Torx drivebit manufactured by SFS intec isrecommended for superior stabilityduring the installation process.
Fasteners installed in less than 1" of solid wood may have an increased potentialfor sealing or connection failure over time. This may be due to the fasteners beingstripped out during installation and/or due to the lack of adequate wood fibermaterial to hold the fastener in place during thermal movement cycles or otherforces which may be exerted upon the connection.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 25/52
Weather Gard® Metal to Wood
Stainless Aluminum Panel Woodgrip™ Woodgrip stainlessFor aluminum pane
23SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0503-09 07 ©2008 SFS intec, Inc.
Stainless, Aluminum Panel Woodgrip is an all stainlesswood fastener designed for use with aluminum panels:• Fastener is 304 stainless steel for corrosion protection.• High hex washer head provides driving stability
and a sharp point for quick installation into aluminum.
• Will not drill steel panels.
Application
StainlessAluminum Panel Woodgrip9 – 15 HWH Sharp PointAssembled withaluminum Bond SealMetal to woodSelf-drills through aluminum paneland taps into wood substrate.Min penetration in wood substrate
should be no less than 1"
Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir
#9 Woodgrip Stainless Aluminum Bond Seal
1-1/2" Penetration 748
1" Penetration 542
Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads dependingupon specific wood density variations. The specific job conditions should be considered and appropriatesafety factors applied. Stainless Woodgrips are not designed to self-drill steel panels.
Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failureover time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequatewood fiber material to hold the fastener in place during thermal movement cycles or other forces which may beexerted upon the connection.
SelectionSize Stainless Woodgrip
1" E0225-CKF
1-1/2" E0270-CKF
2" E0272-CKF
2-1/2" E0275-CKF
3" E0277-CKF
InstallationTools: 0 – 2500 rpm screwdriver equippedwith depth sensing nosepiece.
OptionsPainted
1/4" Hex Washer headThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1657Torsional: 50 in-lbs minShear: 1550
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 26/52
Woodgrip™ Capped Fasteners WoodZAC® and WoodMACFor metal to wood
Weather Gard® Metal to Wood
24SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0504-0 907 ©2008 SFS intec, Inc.
WoodZAC has all the performance features ofstandard Woodgrip fasteners, plus a zinc alloycap that can never red rust:• 5/16" AF high Hex Washer Head for driving stability
and a sharp point for quick installation.
• Assembled with a aluminum bond seal for weather tightseal and improved installation appearance.
WoodMAC has all the performance featuresof standard Woodgrips:• 1/4" AF stainless cupped HWH for a low profile appearance
and can never rust.
Application
WoodZAC9–15 HWH Sharp PointAssembled withaluminum Bond SealMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
WoodZAC12 x 3/4" LAP Sharp PointAssembled with EPDM washerPanel to panel side lap, end lapand other sti tch applications
WoodMAC9–15 HWH Sharp PointAssembled with EPDM washerMetal to woodDrilling capacity: 24 ga (.024)
Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"
WoodMAC Lap12 x 3/4" HWH Sharp PointAssembled EPDM washerPanel to panel side lap, end lapand other sti tch applications
NotesDimensions are nominal inches unless noted.
5/16" Hex Washer HeadZinc Alloy CapThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933
5/16" Hex Washer HeadZinc Alloy CapThread Major Dia: .215 – .208Thread Minor Dia: .164 – .157
Strength (lbs ult.): Tensile: 2100Torsional: 92 in-lbs min.Shear: 1800
1/4" Cupped Stainless CappedThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127
Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933
1/4" Cupped Stainless CappedThread Major Dia: .215 – .208
Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100Torsional: 92 in-lbs min.Shear: 1800
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 27/52
Weather Gard® Metal to Wood
Woodgrip™ Capped Fasteners WoodZAC® and WoodMACFor metal to wood
25SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0504-0 907 ©2008 SFS intec, Inc.
Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir
#9 Woodgrip 5/16" ZAC Aluminum Bond Seal
1-1/2" Penetration 748
1" Penetration 542
#9 Woodgrip 1/4" MAC EPDM Washer
1-1/2" Penetration 748
1" Penetration 542
Notes: Woodgrip and WoodZAC pull out strength values may vary from tabulated loads depending upon specific wood density variations.Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safetyfactors applied when specifying the proper fasteners.
Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time.This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material
to hold the fastener in place dur ing thermal movemen t cycles or other force s which may be exerted upon the conn ection.
SelectionSize WoodZAC WoodZAC Lap WoodMAC WoodMAC Lap
1" C0165-DNF — C0168-CAF —
1-1/2" C0265-DNF — C0268-CAF —
2" C0385-DNF — C0388-CAF —
2-1/2" C0465-DNF — C0468-CAF —
3" C0481-DNF — C0488-CAF —
12 x 3/4" ZAC (5/16" HWH) — A1705-FLF — —
12 x 3/4 " MAC (1/4" HWH) — — — A1708-E YF
InstallationTools: 0 – 2500 rpm screw driver equipped with depth sensing nose piece.
OptionsPainted
Pull-over
28 ga: 433
26 ga: 570
24 ga: 900
28 ga: 380
26 ga: 500
24 ga: 710
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 28/52
Woodgrip™ #14 Milled PointMilled point — Type A milled point
and Type AB ZACFor metal to wood
Weather Gard® Metal to Wood
26SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0505-09 07 ©2008 SFS intec, Inc.
Milled Point carbon steel self-tapping fastenersare designed for attaching both metal to woodand metal to metal:• These fasteners do not require a pre-drilled hole when attaching
26 and 24 gage metal to wood.
ZAC® Milled Point tapping screws have the sameperformance features of milled point tappers with:• Zinc alloy capped head that can never red rust.• Assembled with EPDM sealing washers for a consistent,
weather tight seal.
Application
#14 Type A Milled PointCarbon Steel, Silver SentriMetal to woodSelf-drilling metal thickness:Sheet .018 – .030
Thickness is based on normal,single or multiple material thicknesscombined for total.
Min depth penetration into thewood sub structure: 1"
#14 ZAC Type AMilled PointMetal to woodSelf-drilling metal thickness:Sheet .018 – .030
Thickness is based on normal,single or multiple material thicknesscombined for total.
Min depth penetration into thewood sub structure: 1"
1/4 ZAC Type AB
Milled PointMetal to woodSelf-drilling metal thickness:Sheet .018 – .030
Thickness is based on normal,single or multiple material thicknesscombined for total.
Min depth penetration into thewood sub structure: 1"
Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel material. Ultimate values listed
are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection Part No. Part No. Part No.Length #14 A Milled Point Bond Seal #14 A Milled Point 3/8" ZAC 1/4" AB Milled Point 3/8" ZAC
1" A3321-GBF A3325-FMF A4395-FMF
1-1/4" — — A442 8-FMF
1-1/2" A3438-GBF — A4485-FMF
2" A3531-GBF — A4513-FMF
2-1/2" A3597-GBF — A4510-FMF
3" A3626-GBF — —
InstallationTools: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Hex Washer HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178
Strength (lbs ult.): Tensile: 3500Torsional: 125 in-lbsShear: 2400
Pull-out (lbs ult.): 1" SPF wood: 1013
Pull-over ( lbs ult.): 22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564
3/8" AF Zinc Alloy CappedThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178
Strength (lbs ult.): Tensile: 3500Torsional: 125 in-lbsShear: 2400
Pull-out (lbs ult.): 1" SPF wood: 1013
Pull-over (lbs ult.): 22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564
3/8" AF Zinc Alloy CappedThread Major Dia: .246 – .240
Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 2500
Pull-out (lbs ult.): 1" SPF wood: 1013
Pull-over (lbs ult): 22 ga (.030): 109424 ga (.024): 86626 ga (.018): 600
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 29/52
Weather Gard® Self-Tapping Fasteners
Tapping Screws—Carbon Steel Self-tapping—Type A, AB, BFor metal to meta
27SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0601-0907 ©2008 SFS intec, Inc.
• Carbon steel zinc-plated self-tapping fasteners are the original metalconstruction fastener that can be used in metal to metal and metal to wood applications.
• Tapping screws are available in long lengths for specialty applications.
Application
#14 Type AMetal to metalAttachment thickness: .044 – .075
Metal thickness Drill bit size.021 – .026 1/8 (.125).027 – .050 3/16 (.187).051 – .075 #8 (.199)
The hole size determines installationperformance and pullout strength.
Thickness is based on normal, single thickness purlin/girt or multiplematerial thickness combined for total.
Min projection: 3/8" of threads
below substrate
1/4 Type AB and BMetal to metalAttachment thickness: .044 – .500
Metal thickness Drill bit sizeAB .021 – .026 1/8 (.125)AB .027 – .050 5/32 (.156)AB .051 – .075 #8 (.199)AB .075 – .110 #7 (.201)B .065 – .085 #8 (.199)B .085 – .115 #7 (.201)B .115 – .375 #1 (.228)B .375 – .500 #1 or larger, depending on hardness of steel
Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total.
Min projection: 3/8" of threadsbelow substrate
#17 Type ABStrip out repair Type A or ABMetal to metalAttachment thickness: .03 6 – .06 0
Min projection: 3/8" of threadsbelow substrate
NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the resultof laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
3/8" AF Hex HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178
Strength (lbs ult.): Tensile: 3500Torsional: 125 in-lbsShear: 2400
Pull-out (lbs ult.): 14 ga (.075): 131816 ga (.060): 95818 ga (.048): 605
Pull-over (lbs ult.): 22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564
3/8" AF Hex HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional:142 in-lbsShear: 2560
Pull-out (lbs ult.): 12 ga (.105): 218514 ga (.075): 127716 ga (.060): 879
Pull-over (lbs ult.): 22 ga (.030): 109424 ga (.024): 86626 ga (.018): 600
3/8" AF Hex Head Thread Major Dia: .295 – .285 Thread Minor Dia: .220 – .214
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 30/52
Tapping Screws—Carbon Steel Self-tapping—Type A, AB, BFor metal to meta
Weather Gard® Self-Tapping Fasteners
28SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0601-0907 ©2008 SFS intec, Inc.
Selection Part No. Part No. Part No.Length* #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal
3/4" A2980-GB A4320-GB A3800-GB
1" A3240-GB A4420-GB A3860-GB
1-1/4" A3420-GB A44 40-GB —
1-1/2" A346 0-GB A4500-GB A3920-GB
2 " A3520-GB — A400 0-GB
2-1/2" A3580-GB — A404 0-GB
3" A3620-GB — A4080-GB
3-1/2" A364 0-GB — A4140-GB
4" A368 0-GB — A4220-GB
5" A3720-GB — A4260-GB
6" A3740-GB — A4280-GB
#17 x 3/4" — A6020-K J —
#17 x 1" — A6040-KJ —
#17 x 1-1/2" — A6060-K J —
*Longer lengths available upon request
InstallationTools: 0 – 1000 rpm on type B screwdriver equipped with depth sensing nosepiece.
OptionsSentri ™ Painted ZAC®
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 31/52
Weather Gard® Self-Tapping Fasteners
Tapping Screws—Stainless Steel Stainless self-tapping—Type A, AB, BFor metal to meta
29SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0602-0907 ©2008 SFS intec, Inc.
• Stainless steel zinc-plated self-tapping fasteners aredesigned for attaching metal to metal and metal to wood.
• Type B have wax surface treatment for added lubricity.
• Stainless tappers are used in high corrosive environmentsor where corrosions free performance is required to meet
the design life of the project.
Application
#14 Type A 304 StainlessMetal to metalAttachment thickness: .044 – .075Metal thickness Drill bit size.021 – . 026 1/8 (.125).027 – . 050 3/16 (.187).051 – . 075 #8 (.199)
The hole size determines installationperformance and pullout strength.
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/8" of threadsbelow substrate
Type AB and B 304StainlessMetal to metalAttachment thickness: .04 4 – .50 0
Metal thickness Drill bit sizeAB .021 – .026 1/8 (.125) AB .027 – .050 5/32 (.156) AB .051 – .075 #8 (.199) AB .075 – .104 #7 (.201)
B .065 – .085 #8 (.199)B .085 – .115 #7 (.201)
B .115 – .375 #1 (.228) B .375 – .500 #1 or larger, depending on hardness of steel
Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/8" of threadsbelow substrate
#17 Type AB 304 StainlessStrip out repair Type A or ABMetal to metalMin projection: 3/8" of threadsbelow substrate
NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the resultof laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
3/8" AF 304 Stainless Hex HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178
Strength (lbs ult.): Tensile: 3370Torsional: 125 in-lbsShear: 1520
Pull-out (lbs ult.) 14 ga (.075): 123216 ga (.060): 1110
Pull-over (lbs ult.): 22 ga (.030): 123724 ga (.024): 79026 ga (.018): 647
3/8" AF 304 Stainless Hex HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 235 0
Pull-out (lbs ult.): 12 ga (.105): 231014 ga (.075): 139416 ga (.060): 1250
Pull-over (lbs ult.): 22 ga (.030): 123724 ga (.024): 79026 ga (.018): 647
3/8" 304 Stainless AF Hex HeadThread Major Dia: .295 – .285Thread Minor Dia: .220 – .214
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 32/52
Tapping Screws—Stainless Steel Stainless self-tapping—Type A, AB, BFor metal to meta
Weather Gard® Self-Tapping Fasteners
30SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0602-0907 ©2008 SFS intec, Inc.
Selection Part No. Part No. Part No.Length #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal
3/4" E0500-HP E1240-HP E0860-HPW
1" E0600-HP E1300-HP E0880-HPW
1-1/4" E0640-HP E1310-HP —
1-1/2" E0660-HP E1320-HP E1000-HPW
2" E0700-HP — E1060-HPW
2-1/2" E0720-HP — E1080-HPW
3" E0740-HP — E1100-HPW
3-1/2" E0760-HP — E1120-HPW
4" E0780-HP — E1140-HPW
5" E0820-HP — E1180-HPW
6" E0840-HP — E1200-HPW
7" E0850-HP — E1210-HPW
8" E0855-HP — E1215-HPW
#17 x 3/4" — E1960-KP —
#17 x 1" — E1980-KP — #17 x 1-1/2" — E2000-KP —
InstallationTools: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece.
OptionsPainted
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 33/52
Weather Gard® Self-Tapping Fasteners
Tapping Screws — Milled Point Self-tapping #14 milled point Type AFor metal to wood and metal to meta
31SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0603-0 907 ©2008 SFS intec, Inc.
• Milled point carbon steel self-tapping fasteners are designedfor attaching both metal to wood and metal to metal.
• Milled point fasteners do not require a pre-drilled hole whenattaching 26 and 24 gage metal to wood.
• For attaching metal to metal they have the same performanceas standard A tappers. See tapping screw section.
• Zinc plated and Silver Sentri™ coated for extendedcorrosion resistance.
Application #14 Type A Milled PointMetal to woodMetal to metalSelf-Drilling Metal Thickness:Sheet .018 – .030
Thickness is based on normal,single or multiple material thicknesscombined for total.
Min penetration into the woodsub structure: 1"
NotesDimensions are nominal inches unless noted. Pull out values (pounds ultimate) are based on 50,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. T he specific job conditions should be considered and appropriate safe ty factor s applied when specifying the proper fas teners.
Selection Part No.Length #14 A Milled Point Bond Seal
1" A3321-GBF
1-1/2" A3438-GBF
2" A3531-GBF
2-1/2" A3597-GBF
3" A3626-GBF
InstallationTools: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece.
5/16" AF Hex Washer HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178
Strength (lbs ult.): Tensile: 3500Torsional: 125 in-lbsShear: 2400
Pull-out (lbs ult.): 1" SPF Wood: 1013
Pull-over (lbs ult.): 22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564
OptionsSentri ™ Painted ZAC®
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 34/52
Confas™ Concrete FastenersConfas concrete tappers—
Carbon steel and 304 stainless steeFor attachment to concrete
Weather Gard® Self Tapping Fasteners
32SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0604-0 907 ©2008 SFS intec, Inc.
• Confas — Slotted Hex Washer Head and Phillips/flathead anchoring system for concrete, block and brick.
• One-piece system provides many installation benefitswith exceptional performance.
• Exclusive in-house applied Sentri XP™ coating, providingexcellent resistance to rust and corrosion.
• 304 austenitic stainless provides ultimate corrosion performance.
Application3/16" DiameterAvailable lengths:1-1/4" to 4"Carbon Steel304 StainlessSlotted Hex Washer HeadPhillips flat headSpecial close tolerance bitsare required to ensuresystem performance.
The hole tolerance differs forcarbon steel and stainless,so bit selection is of importance.
It is recommended that the hole depthexceeds the fastener length by 1/2".However, penetration beyond 1-1/2"is not desirable.
1/4" DiameterAvailable lengths:1-1/4" to 6"Carbon Steel304 Stainless
Slotted Hex Washer HeadPhillips flat headSpecial close tolerance bitsare required to ensuresystem performance.
The hole tolerance differs forcarbon steel and stainless,so bit selection is of importance.
It is recommended that the hole depthexceeds the fastener length by 1/2".However, penetration beyond 1-1/2"is not desirable.
Notes
Dimensions are nominal inches unless noted. Performance of Confas is subject to proper hole size and characteristics of the masonry material into which the anchors aredriven. Ultimate values listed are the result of laboratory testing. Since safety factors can vary from job to job, application reference should always be made to the applicablecodes for specific safe working ratios. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
OptionsNone
1/4" Slot ted Hex Washer Head #3 Phillips Flat HeadThread Major Dia: .215 – .205Thread Minor Dia: .127 – .123
Recommended hole s ize:0.168 – .0175
Pull-out 1-1/4" penetration (lbs ult.): Concrete slab: 1700Hollow block: 580Face brick: 990
Typical shear values (lbs ult.): Concrete block:Solid limestone: 683(132 lbs per cubic feet)
Concrete block:Expanded slag: 917(116 lbs per cubic feet)
Red clay brick: 1067(136 lbs per cubic feet)
Poured concrete: 1133(6800 psi)
5/16" Slotted Hex Washer Head #3 Phillips Flat HeadThread Major Dia: .255 – .245Thread Minor Dia: .172 – .168
Recommended hole s ize:.0202 – .0204
Typical shear values (lbs ult.):
Concrete block:Solid limestone: 1017(132 lbs per cubic feet)
Concrete block:Expanded slag: 1083(116 lbs per cubic feet)Red clay brick: 1583(136 lbs per cubic feet)Poured concrete: 193 3(6800 PSI)
Pull-out 1-1/4" penetration (lbs ult.): Concrete slab: 1767Hollow block: 647Face brick: 1050
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 35/52
Weather Gard® Panel Clips and Fasteners
Standing Seam Clips Engineered panel clipsFor standing seam panel attachments
33SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0701-0907 ©2008 SFS intec, Inc.
• Engineered panel clips are custom designed and manufacturedfor your panel system.
• Clips are supplied in galvanized steel, coated steel,stainless steel and other materials.
• Engineered fixed and float clip designs are available.
• Standard clips are available from stock without tooling cost to you.• Sealant can be pre-applied to the clips to maintain the seal
at the clip attachment.• Clip design options are available for review and evaluation.
Application
Snap Lock Panel DesignConfigurations require very low profileclip bases with a base feature to hold
the panel above the low profilefastener heads.
Selection
1-1/2" Snap Lock ClipG90 Galvanized: 18 ga. or 20 ga.Packaged 500 per carton
1-3/4" Snap Lock(1 hole) ClipG90 Galvanized: 18 ga.Packaged 500 per carton
1-3/4" Snap Lock(3 hole) ClipG90 Galvanized: 20 ga.Packaged 500 per carton
Application
Architectural Panel DesignConfigurations require low profilebases with clearance for thefastener head.
Fixed Clips are primarily used with thesepanels. Low profile head fasteners shouldbe used with these panels to provideclearance for the panel over the fastenerheads. These clips are manufactured fromsteel, stainless steel and other materialswith various finishes to fit the needs of thepanel application.
Roof Panel
Roof Panel
Clip
BlanketInsulation
Roof Purlin
Low ProfileHead Fastener
1-1/2" Snap Lock ClipG90 Galvanized: 24 ga.Packaged 1000 per carton
1-3/4" Snap Lock(2 hole) ClipG90 Galvanized: 18 ga.Packaged 250 per carton
Fixed and Float Clips are used with thesepanels. The clips may have pre-appliedsealant to maintain the panel seal at theclip attachment point. These clips aremanufactured from steel, stainless steeland other materials with various finishes to fit the needs of the panel application.
Roof Panel
Sliding ClipAssembly
BlanketInsulation
Roof Purlin
Roof Panel
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 36/52
Standing Seam Clips Engineered panel clipsFor standing seam panel attachments
Weather Gard® Panel Clips and Fasteners
34SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0701-0907 ©2008 SFS intec, Inc.
Selection
1-1/2" Single Lock Fixed ClipG90 Galvanized: 22 ga.
Packaged 700 per carton
2" Single Lock Fixed ClipG90 Galvanized: 22 ga.Factory applied sealantPackaged 250 per carton
2" Single Lock Utility ClipG90 Galvanized: 22 ga.Factory applied sealantPackaged 400 per carton
2" Double Lock Fixed ClipG90 Galvanized: 22 ga.
Factory applied sealantPackaged 250 per carton
2" Double Lock Fixed Clipwith Panel ShelfG90 Galvanized: 22 ga.Factory applied sealantPackaged 250 per carton
OptionsAlso Available in Stainless Steel
2" Single LockFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged 100 per carton
2" Double LockFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged 100 per carton
1-1/2" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton
2" Mechanical SeamFloat Clip
G90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton
2" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged Low 100 per cartonor High 70 per carton
3" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 37/52
Weather Gard® Panel Clips and Fasteners
Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood
35SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0702-0708 ©2008 SFS intec, Inc.
• Designed with unique head styles, drill pointconfigurations and material types to meet performancerequirements to attach standing seam roof clips.
• Engineered profile features preventing paneldamage from fastener head contact.
• Engineered installation torque drive controlfor uniform installation performance.
Application #10 Type A: Pancake Head2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to wood
#10 Type A: Pancake HeadPhillips DriveStainless SteelMetal to wood
#10 Self-Drill: Pancake Head2/2 Quadrex Drive
Carbon Steel, Zinc PlatedMetal to metalMin projection: 3/8" of threadsbelow substrate
#12–8 XG Sharp Point: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood
#12 Type A: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood
#12 Self-Drill: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to metalMin projection: 3/8" of threadsbelow substrate .
Head Height: .080 – .068Head Dia: .447 – .423Thread Major Dia: .194 – .188Thread Minor Dia: .133 – .126
Strength (lbs ult.): Carbon Stainless Tensile: 1825 1653Torsional: 48 in-lbs 50 in-lbsShear: 1535 1587
#10 Type A, Pull-out (lbs ult.):
SPF wood:1" penetration: 821
#10 Self Drill, Pull-out (lbs ult.): 12 ga (.105) : 178214 ga (.075): 107216 ga (.060): 782
Roof Panel
Roof Panel
Clip
BlanketInsulation
Roof Purlin
Low ProfileHead Fastener
Head Height: .080 – .068Head Dia: .447 – .423Thread Major Dia: .221 – .215Thread Minor Dia: .162 – .155
Strength (lbs ult.): Tensile: 1940Torsional: 90 in-lbsShear: 1805
Pull-out (lbs ult.): SPF wood:
1" penetration: 724
Head Height: .080 – .068Head Dia: .447 – .423Thread Major Dia: .215 –.209Thread Minor Dia: .113–.127
Strength (lbs ult.): Tensile: 2183Torsional: 60 in-lbsShear: 1946
Performance (lbs ult.): Pull-out SPF 1-1/2" Penetration 874SPF 1" Penetration 5711x4" Pine 5903/4" Plywood 5875/8 " Plywood 4461/2" Plywood 38423/ 32" OSB 52419/32" OSB 456
Head Height: .090 – .078Head Dia: .447 – .423Thread Major Dia: .215 – .209Thread Minor Dia: .164 – .157
Strength (lbs ult.): Tensile: 2900Torsional: 92 in-lbsShear: 2050
Pull-out (lbs ult.): 12 ga (.105) : 153914 ga (.075): 101016 ga (.060): 724
Continued on following page
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 38/52
Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood
Weather Gard® Panel Clips and Fasteners
36SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0702-0708 ©2008 SFS intec, Inc.
Application
1/4 -14 #2 PointDrilling capacity (#2 point): .050 – .150
Attachment thickness:Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/8" of threadsbelow substrate
12-24 #5 Point: Pancake Head2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to metal
Drilling capacity: .075 – .500Attachment thickness:Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.
Min projection: 3/8” of threadsbelow substrate
NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result oflaboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Fasteners installed in less than 1" of solid wood may have an increased potential for a connection failure over time. This may be due to the fastener s being stripped out duringinstallation and/or due to the lack of adequate wood fiber material to hold the fastener in place when forces are exer ted upon the connection.
Selection
5/16" AF Hex Washer Head3/8" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185
Strength (lbs ult.): Tensile: 3800Torsional: 150 in-lbsShear: 2850
#2 Point, Pull-out (lbs ult.): 12 ga (.105): 208814 ga (.075): 131216 ga (.060): 903
BlanketInsulation
Roof Panel
Roof Purlin
Roof PanelClip
Roof Panel
OptionsSentri ™
Head Height: .090 – .078Head Dia: .447 – .423Thread Major Dia: .216 – .210Thread Minor Dia: .186 – .181
Strength (lbs ult.): Tensile: 3450
Torsional: 100 in-lbsShear: 2420
Pull-out (lbs ult.): 12 ga (.105): 13783/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value
InstallationTools: 2000 – 2500 rpm #10 self drill, 0 – 2000 rpm on 1/4-14 self drill screwdriver equipped with depth sensing nosepiece.
Length
#10 Type APancake
Carbon Steel
#10 Type APancake
Stainless Steel #10 Self-Drill
Pancake #12–8 XGPancake
#12 Type APancake
#12 Self-DrillPancake
12–24 #5 PointPancake
1/4–14 #2 Point5/16 AF HWH
1/4–14 #2 Point3/8 AF HWH
1" A1191F E0235F S3431F A1900F A1710F S4552F — — S5171F
1-1/4" — — — — — — — S5191F —
1-1/2" A1351F — S4221F A1940F — — S4750F S5286F S5271F
2" A1391F E0271F S4421F A1950F — — — — —
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 39/52
Weather Gard® Closure and Venting Products
WG-7™ Closure WG-7 closure and WG-7 adhesive closureFor panel opening fille
37SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0801-0907 ©2008 SFS intec, Inc.
• The original industry closure material — time tested-millionsof feet installed over the last 30-plus years.
• Polyethylene foam for exceptional strengthand compressibility.
• Most configurations are cut with dovetails that eliminate
gapping between pieces.
• Moisture and water vapor transmission is barely measurable.• Adhesive applied to the contact side of the panel surface
assures positive positioning during installation.• Resist damaging ultra violet rays and ozone deterioration.• Over 1800 panel configurations available.
• Manufactured in multiple plants for quick delivery.
Typical Inside Closure Application Typical Outside Closure Application
Endwall
Closure
Roof Panel
SidewallRoof Panel
EndwallClosure
Sidewall
Application
WG-7 ClosureMaterial Thickness: 1", 1-1/2", 2"
Color: Grey
FeaturesProperty Units Properties*
Nominal density lb/f t3 1.5 – 2.0Skin/Skin
Recommended operating degrees F +212 max temperature range -94 min
Compression stress-strain characteristics
10% compression psi 4.64
25% compression psi 7.54
50% compression psi 16.53
Compression set
(22 hrs, 25% compression, 23˚C)
1/2 hour recovery % set 12
24 hour recovery 5
Tear strength ft-lbs 295
Tensile strength psi 46.27
Elongation % 102
Thermal conductivity
(at mean temp of 50˚ F) BTU/ ft-hr.-degrees F 0.02 3
Horizontal Burning Characteristics Burn Rate
0.197" thickness in/sec 0.0830.512" thickness in/sec 0.059
FMVSS. 302 (pass thickness) in 0.394" and above
Shore Hardness 00 scale
(min. 0.394" cell/cell thickness) 43
*All properties are nominal values and are subject to change.
OptionsNone
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 40/52
Pipe Flashing Square and round base pipe flashingFor roof pipe flashing
Weather Gard® Closure and Venting Products
38SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0802-0907 ©2008 SFS intec, Inc.
Application
Square BaseSize Pipe size Base size
1 1/4 – 2" 4-1/2"
2 1-1/4 – 3" 6"
3 1/4 – 4" 8"
4 3 – 6" 10"
5 4 – 7" 11"
6 5 – 9" 12"
7 6 – 11" 14"
8 7 – 13" 17"
9 10 – 18" 25"10 13 – 26" 34"
Round BaseSize Pipe size Base Size
1 1/4 – 2" 4-3/4"
2 1-3/4 – 3-1/4" 6-1/4"
3 1/4 – 5" 7-3/4"
4 3 – 6-1/4" 9-1/4"
5 4-1/4 – 7-1/2" 10-3/4"
6 5 – 9" 12-1/4"
7 6 – 11" 14-1/4"
8 7 – 13" 16-1/2"
9 10 – 19" 25-1/2 "
Retrofit Square BaseSize Pipe size Base Size
1 1/2 – 4" 8-3/16"
2 4 – 9-1/4" 14-1/4"
3 9-1/4 – 16-1/4" 21-1/2"
Material SpecificationsTest Type EPDM Silicone (Hi-Temp)
Advance ozone resistance
70 Hrs. 70 Hrs. test @ 500 pphmHigh temperature:
Intermittent +275º F +500º F
Continuous +212º F +437º F
Low temperature:
Resistance tested to -65º F -100º F
Tensile strength 1450 psi 700 psi
OptionsNone
• Pipe opening can be easily customized on job sightutilizing clearly marked pipe diameters on each flashing.
• EPDM and Silicone are both flexible materials, resistant to ultraviolet rays, cracking or weathering.
• Available in EPDM black or gray and silicone red.
• The aluminum base is corrosion resistant and conformseasily to any panel configuration or roof pitch.
• Retrofit flashing is available for piping with welded capsor cross bars.
• Square base also available in white, terra cotta, bright red,
light green, dark green, light blue, dark blue and brown.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 41/52
Weather Gard® Closure and Venting Products
ProfileVent® Metal roofing ridge vent
39SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0803-0 907 ©2008 SFS intec, Inc.
• 40 year limited warranty
• Glue spots prevent slippingduring installation
• Fits under any ridge cap
• Fits any pitch 2:12 – 20:12• One person roll-out installation
• Won’t scratch panel finish
• Won’t crack, dent or rust duringshipping or installation
• Won’t clog from airborne dust
• Prevents insect infiltration
• Prevents snow infiltration• Provides proven roof ventilation
• Meets all model building codes
• Packing in English, Frenchand Spanish
• No waste—use leftoverson next job
• Will not support a flame• Made in U.S.A.
Eagle Crest/Ameridrain®
5-V Panel
Ambler/Pro Panel II
Rydal/Channeldrain 2000®
3/4" Hi Rib
M/U Panel
Agri Panel
Devon/Delta Rib
2.67 Corrugated
Uni-Rib ™
Morton Hi Rib
Regal Rib®
Rugged Rib®
7/8" Wide Rib®
Perm-A-Clad®
DuroClad
Wayne/Spanline
R Panel
Multi Rib
Tile Sheet 25/1100
LS-28 Large Tab
Ultra Lock
AP Panel
Pro-S 12 Panel
Royal Lock ™ 12"
Royal Lock ™ 16"
SL-12®
SL-16®
1" x 5/16" x 12"*
1" x 5/16" x 16"*
Alu-Loc
Medallion Loc*
Metalogic 2000 (12")
Metalogic 2000 (16")
Metalogic 2000 (18")
Metalogic 3000 (12")
Metalogic 3000 (16")
SSR Panel 16"
SSR Panel 18"
Application
ProfileVentNew or re-roof on Purlinor wood deck Construction:Use a 2" opening at the r idge
to provide ventilation. On newor re-roof wood deck construction,cut a 2" slot at the ridge (1" each side,start cut 6" from gable ends).On purlin construction position panels
to leave a 2" opening.
Available in convenient sizes• 20' package
• 50' package
• 100' package
Current panel profiles
*No positioning glue.Note: The trademarks listed above are those of the respective roof panel manufacturers.
1Allow 2" opening at ridge forventilation. ProfileVent is rolled
out along the ridge, gable to gable,about 1" up-slope from the ridge capedge. The positioning adhesive onmost profiles will hold ProfileVent inposition and allow for repositioning.
3Screw down or pop rivet the ridgecap according to manufacturer’s
instructions (works with any ridge cap).2ProfileVent can be cut with
scissors or utility knife.
Inset: When splicing ProfileVent,make the splice at the center top of the high rib and use caulk or sealantalong the splice.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 42/52
Ventco™ Ridge Cap Anchor Clip Ridge cap anchor clip
Weather Gard® Closure and Venting Products
40SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0804-0 907 ©2008 SFS intec, Inc.
1Install your metal roofing panelaccording to manufacturer’s
instructions. Apply mastic above andbelow pre-drilled holes in the clip.Before installing ProfileVent®, insert #14A screw through the large down-slope access hole in top of the RidgeCap Anchor Clip.
Anchor clips are recommended in high wind areas and on panels with major ribs 16" on center or greater.
Anchor Clip Detail
2Lift the back end of clip. SlipProfileVent under the clip. Push
clip back down and insert another #14A screw in the up-slope hole.
Application
Ventco™ Ridge Cap Anchor ClipAn independent engineering corporation tested the performanceof the Ventco Ridge Cap Anchor Clip under high wind loading.During testing, a roof/ridge vent/cap system was subjected to wind
speeds that follow the Dade County Test protocol.
The following observations were made concerning theperformance and structural integrity of the clip and ridge cap:• No lift ing of the ridge cap up to 115 mph
• No fastener pull out or loosening
• The ridge cap remained in contact with ventilation system
• No difference in performance when the cap is secured to the clip with screws or rivets
Specifications• 20 gauge galvanized steel
• Visible surface painted black for aesthetic purposes
Packaging• 25 clips per small box
• 24 small boxes per master box
• 600 clips per master box
M9002
3/4" Anchor ClipM9004
1" Anchor ClipM9006
1-1/4" Anchor ClipM9008
1-1/2" Anchor ClipM9010
1-3/4" Anchor ClipM9012
2-1/2" Anchor Clip
OptionsNone
Anchor Clip U.S. Pat. 6418678 (other patents pending)
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 43/52
Weather Gard® Tools, Belted Fasteners and Accessories
Installation Screw Guns Installation screw guns and drive socketsInstallation tools
41SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0901-0508 ©2008 SFS intec, Inc.
• Screw guns and noise pieces are matched for individual products to insure consistent installation performance.
• Screw gun manufactures and individual tools are tested andpre-qualified for reliable field performance beforerecommendation.
Application
DI 600 Power ScrewdriverFor installingself-drilling fastenersFeature: Versa clutch system
CF 50 Setting Nose PieceInstallation tool with depth
locator for long SX compositepanel fastenersFeatures:
ZA 1/4"/ 80 drive shaft
E 380 drive socket
irius® Drive SocketThe E-420 setting tool is requiredfor installing the irius drive systemThe fasteners are clamped firmlyvia the teeth under the fastener head
Hex and Torx® Drive Bits1/4" Hex one piece magnetic driveSize Part No.
1/4" Hex J0865
5/16" Hex J0875
3/8" Hex J0925
1/4" Torx one piece drive bitSize Part No.
6-Lobe, 2-3/4"-long drive bit J1990
Volts: 110Amps: 6.5
Speed: 0 – 2000 rpm variable speed
Socket E-420
E-420 parts kit
Spare jaws
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 44/52
Panelmaster™ Assembled belted fasteners
Weather Gard® Tools, Belted Fasteners and Accessories
42SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0902-0508 ©2008 SFS intec, Inc.
• Increased speed of installation• Improved working ergonomics• Stand-up roof attachment
• Fasteners installed uniformly every time• Special footpieces available for attachment through the panel rib• Installs fasteners 1"– 3" long
ApplicationPanelmaster™ Tool KitStandard tool kit includes:– Panelmaster tool
– DeWalt® 18V drive unit
– Battery charger and extra battery
– One extension piece
– Extra drive bits
– Corded DeWalt drive unit available
– One-year full replacement warranty
Belted Fasteners– SFS intec fasteners 1" through 3" lengths
with sealing washers
– Can be painted to match any panel color
– All fasteners packaged 500 per carton
Woodgrip™ Fasteners
Item Length SFS Part #Woodgrip 9 –15 HWHControl Seal WasherSentri Coated
1" C0161-CCBL
1-1/2" C0261-CCBL
2" C0381-CCBL
2-1/2" C0461-CCBL
3" C0485-CCBL
Woodgrip 9 –15 HWH.001" Mech ZincControl Seal WasherSentri Coated
1" C0167-CCBL
1-1/2" C0267-CCBL
2" C0382-CCBL
2-1/2" C0467-CCBL
3" C0487-CCBL
HiLo Woodgrip 10 –15HWH Bond Seal WasherSentri Coated
1" A1067-CDBL
1-1/2" A1072-CDBL2" A1077-CDBL
2-1/2" A1082-CDBL
3" A1087-CDBL
Woodgrip XG 12 –11 HWHBond Seal WasherSentri Coated
1" A1806-EMBL
1-1/2" A1841-EMBL
2" A1851-EMBL
2-1/2" A1856-EMBL
3" A1861-EMBL
Long-Life Fasteners
Item Length SFS Part #WoodZAC 9-15 HWHSeal Washer
1" C0165-DNBL
1-1/2" C0265-DNBL
2" C0385-DNBL
2-1/2" C0465-DNBL
3" C0481-DNBL
WoodMAC 9-15 HWHSeal Washer
1" C0168-CABL
1-1/2" C0268-CABL
2" C0388-CABL
2-1/2" C0468-CABL
3" C0488-CABL
Evergrip ™ 9-15 HWHStainless Bond Seal Washer
1" E4160-CUBL
1-1/2" E4260-CUBL2" E4380-CUBL
2-1/2" E4460-CUBL
Evergrip 9-15 TorxStainless Bond Seal Washer
1" 1110324
2" 1110327
3" 1110329
Selection
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 45/52
Weather Gard® Tools, Belted Fasteners and Accessories
Blind Rivets — Grommet FastenersBlind rivets attach light gage
Grommet fasteners attach fiberglass panels
43SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0903-0 907 ©2008 SFS intec, Inc.
Blind rivets• Allow for one side attachment of light gage metal panels through a pre-drilled hole.• Available in steel and aluminum or stainless for applications requiring corrosion resistance performance.• Available pre-painted to color match the panel.
ApplicationBlind RivetsMaterials: Mandrel Rivet:Aluminum AluminumStainless Stainless
Material Size Part No. Grip Range Pre-Drill Hole Size
Aluminum AA4 3D L0520 .126 – .187 #30 (.129 – .133)Stainless STST43D L1290 .126 – .187 #30 (.129 – .133)
Grommet fasteners• Allow for one side attachment of fiberglass panels through a pre-drilled hole.• Designed to pull fiberglass panels together without cracking the material.• Come assembled with EPDM washers for a weather tight seal.
Application
Grommet FastenersMaterials:
Neoprene rubberw/ molded brass nut
Size 3/8" Grommet:Part No. E0260-CSFastener:10-32 x 1-1/4" stainless5/16" AF Hex Head
Washer:15 mm O.D stainless Bond Seal
Size 1/4" Grommet:Part No. E0080-CUFastener:
6-32 x 1-1/4" stainless1/4" AF Hex Head
Washer:12 mm O.D stainless Bond Seal
NotesDimensions are nominal inches unless noted.
OptionsPainted
Stocking Colors:
001 White012 Blue014 Bright White020 Tan042 Burnish047 Green051 Dk. Gray109 Beige110 Brown228 Green232 Green248 Lt. Stone348 White578 Gray
850 Ash Gray890 Red
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 46/52
Weather Gard™ CoatingsWeather Gard
44SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0902-0907 ©2008 SFS intec, Inc.
Threaded fasteners for roofing and siding systems are
available in a wide range of materials, designs, and
coatings. When specifying your fastener, be sure to
choose one that has a performance life equaling or
exceeding the life of the proposed project.
Fastener Materials
Common Fastener compositions:
• Zinc plated and paint coated carbon steel
• Alloy capped fasteners with zinc-aluminum,stainless steel, and nylon capped head designs
• Stainless Steel: 300 Series austenitic stainless steel
• Stainless Steel: 400 Series martensitic stainless steel
• Bi-metal: stainless head and threaded shank with a
joint welded hardened carbon steel drill or sharp point
Coated Corrosion-Resistant Fasteners
SFS intec offers various coating systems such as
electroplating, mechanical plating, Silver Sentri, ™ Color
Sentri and Chromagard ™ paint. Silver Sentri and Color
Sentri are plastic alloy coatings that SFS intec applies
as a barrier coating. Zinc serves as a sacrificial coating
to provide cut-edge plating protect ion.
Metal Alloy Capped Fasteners
ZAC® Zinc Aluminum Capped Head
ZAC design fasteners provide the corrosion resistance
of a zinc-aluminum alloy capped head on a hardened
steel fastener for sel f-drilling or self-tapping installation.
ZAC is the original capped zinc-aluminum head fastener
and is used in more metal buildings than any other
capped fastener.
ZAC design fasteners are available with a 5 /16" and
3/8" capped hex washer head in Impax ™ self-drilling
fasteners, Woodgrip ™ sheet-to-wood fasteners and
self-tapping screws.
MAC™ Stainless Capped Head Self-Drilling Fasteners
MAC stainless capped head design combines the
corrosion resistance of stainless steel and a hardened
steel fastener for self-drilling installation. MAC design
fasteners are available with a 5/16" capped hex washer
head in a wide selection of Woodgrips and Impax
self-drilling fasteners.
Prisma™ Nylon Head Self-Drilling
and Self-Tapping Fasteners
Prisma design fasteners combine the corrosion
resistance of a nylon-molded head with a hardened
steel fastener for self-drilling and self-tapping
installation. The nylon head is formulated with the color
built in. It naturally resists fading and will never rust
like steel headed fasteners. Prisma design fastenersare avail-able with 3/8 " and 7/16" hex washer heads in
self-drillers, Woodgrip metal-to-wood fasteners, and
self-tapping AB fasteners.
Fastener Design
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 47/52
Weather Gard
45SFS intec, Inc. | Weather Gard ™ Product Group | 1-800-234-4533 ©20 08 SFS intec, Inc.
Stainless Steel FastenersA commonly held belief that stainless steel will not rust
or corrode is not necessarily accurate. Stainless steel
is a generic term covering over 200 different t ypes
of alloys that, to varying degrees, corrode less than
carbon steel. It is important that a specifier be aware of
the panel and project performance expectations when
specifying stainless steel fasteners.
Several types of stainless steel are used for fasteners.
300 Series Stainless/Austenitic
• 18-8 stainless alloy with 18% chromium and 8% nickel
• Best known grades are 304 and 316, both work
hardened in the thread-rolling process to manufacture
a self-tapping fastener capable of tapping threads
into steel
• Can be manufactured as a self-drilling, bi-metal
fastener by incorporating a heat-treated hardened
carbon steel drill point joint welded to the austenitic
stainless fastener
• Nonmagnetic
• Provides excellent corrosion resistance compared tomartensitic 410SS fasteners and plated steel fasteners
• Austenitic stainless steel is considered the only type
of stainless steel for panel fasteners
410 Series Stainless/Martensitic
• Stainless alloy with 11.5% to 13.5% chromium
• Can be heat treated to provide hardness to
manufacture as self-tapping or self-drilling
fasteners (when hardened, the part has less
corrosion resistance)
• Poor corrosion resistance compared
to austenitic stainless
• Magnetic
• Plated to improve corrosion resistance
(like carbon steel fasteners)
• Martensitic stainless is not considered
suitable for panel fasteners
Bi-Metal Fasteners
SX Fastener: Austenitic Stainless Self-Drilling Fasteners
SX design fasteners combine the corrosion resistance
of an austenitic 300 series stainless head and threaded
shank with a hardened carbon steel point for self-
drilling installation. These bi-metal fasteners install
like carbon steel fasteners and provide the corrosion
resistance of 18-8 300 series austenitic stainless. SX
fasteners are true stainless steel self-drilling fasteners.
When selecting a stainless steel fastener for any
application where minimizing or virtually eliminating
corrosion is the goal, a specifier should strongly
consider the dramatically greater benefits of 3 00
series over 400 series stainless steel fasteners. The
richer chemical composition and required blade (SX)
or welded drill point make 300 series stainless steel
fasteners more costly, but the corrosion resistance
benefits are far superior.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 48/52
Weather Gard
46SFS intec, Inc. | Weather Gard ™ Product Group | 1-800-234-4533 ©20 08 SFS intec, Inc.
Washer design contributes to the weather seal of a
fastener. SFS offers several washer options based upon
the type of fastener and the applicat ion requirements.
Bonded Washer
• EPDM rubber bonded to metal
• Metal washers are available in galvanized
steel, aluminum, and stainless steel
• Bonded washers offer a low-profile appearance
• Provides positive weather seal between
panel and fastener head
Sealer Cupped Hex Washer Head
• EPDM rubber captured under integral
cupped hex head washer
• Cupped washer head prevents overdriving
• EPDM washer and cupped head offers
an excellent weather seal
• EPDM is protected from UV rays
by cupped washer head
Control Seal
• EPDM rubber captured under the stamped “dome”
• Available on all Woodgrip drill screws
• Reinforced domed shoulder distributes clamp load• EPDM sealant compressed in three key areas
• Weather tight seal even if fastener is driven
in on an angle*
Fastener Head Styles
SFS offers a wide variety of fastener head sty les
designed to meet your project and fastener
requirements. Each head style will provide proper
panel attachment and desired finish appearance.
Available fastener head sty les are:
• irius® drive, low profile
• HWH (hex washer head)
• Cupped hex washer head sealer
• Metal-alloy capped cupped:
HWH ZAC or HWH MAC
• Pancake head
*Proper installation techniques should always be employed.
Washer Styles
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 49/52
Weather Gard
47SFS intec, Inc. | Weather Gard ™ Product Group | 1-800-234-4533 ©20 08 SFS intec, Inc.
Fastener and steel gauge sizes used throughout this Weather Gard section are nominal.
Fastener SizesFastener Size #10 #12 #14
Thread Diameter Decimal Equivalent .190 .216 .250
Steel Gauge Sizes*
Gauge 30 28 26 24 22 20 18 16 14 12 10
Decimal Equivalent .012 .015 .018 .024 .030 .036 .048 .060 .075 .105 .135* Standard steel thickness used for panels, purlins and girts.
Fasteners are designed to withstand a varied range
of types of loading. Each panel or structural system has
its own specific fastener loading requirements. Care
must be taken to ensure that the appropriate loading
requirements for each application are considered.
Typical structural performance criteria that influence
fastener design include:
Ultimate Tension Strength
The point at which a fastener fails under a load
exerted in two direct opposite directions.
Typical ultimate tension strengths of each fastener type
are provided on the fastener information pages.
Ultimate Torsion Strength
The point at which a fastener fails under a twisting
load exerted on the head during installation in
a torsional direction.
Typical ultimate torsion strengths of each fastener type
are provided on the fastener information pages.
Ultimate Shear StrengthThe point at which a fastener fails under
a load exerted in offset opposing directions,
usually upon the shank of the fastener.
Typical ultimate shear strengths of each
fastener type are provided on the fastener
information pages.
Pull-out Performance
The ability of a fastener’s threaded connection
to remain intact and resist tensile loads.
Self-tapping fasteners require that a pilot hole be
drilled prior to installation. The pullout resistance
will be directly related to the pilot hole diameter.
Self-drilling fasteners have been developed,
and are available, for most steel construction
applications, to a metal thickness of 1/2". This type
of fastener is manufactured with its own integral drill
point, which is engineered to drill the optimum hole
size to facilitate eff icient thread forming in the metal
structure, resulting in optimized pullout values.
Pull-over Performance
The ability of a fastener to resist the pulling of
the fastened sheet material over the head of the
fastener due to gravity, wind, or other load.
The resistance to pullover failure is related to the
strength and diameter of the fastener washer and
the strength and thickness of the metal panel.
Structural Performance
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 50/52
Weather Gard
48SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0902-0907 ©2008 SFS intec, Inc.
Plating Definitions
Electroplating is a method of depositing zinc on the
surface of the part using an electrolytic at traction of
the zinc to the fastener. Electroplating deposits a dense
coating of zinc over the entire surface of the part.
The zinc plating is a sacrificial coating protecting the
base part from scratches or other coating breaks.
Mechanical plating is a method of depositing zinc
on the surface of the part using a hammering or impact
process. This method applies the zinc to the entire
surface of the part. Mechanical plating deposits a less
dense, but thicker coating of zinc over the surface
of the part. The zinc plating is a sacrificial coating
protecting the base part from scratches or other
coating breaks.
Sentri™ Corrosion Resistance Coating
Silver Sentri ™ and Color Sentri ™ are proprietary heat-
cured plastic alloy coatings that SFS intec applies
to the entire sur face of the plated steel fastener.
Chemically, Sentri is a metallic filled organic polymer
coating applied to fasteners by means of a dip/ spin/
cure process. Both Silver and Color Sentri are applied
in multiple coats to a prescribed finished film thickness.
Each coat is oven cured after application for maximum
adhesion and corrosion protection. Color Sentri isavailable in a variety of colors to match selected panel
colors. Fasteners with sealing washers are assembled
prior to coating so that all of the final assembly surfaces
are coated with the corrosion-resistant film.
Coatings
Sentri coating exceeds Factory Mutual 4470 corrosion-resistance standard.
Kesternich Accelerated Corrosion Testing
Below is a comparison of Silver Sentri coated fasteners, G-90 galvanized and Galvalume ® corrosion resistance
in Kesternich accelerated corrosion testing. Kesternich cabinet testing simulates acid rain conditions and is
used worldwide for accelerated corrosion testing.
7/17/2019 SFS Weather Gard May08
http://slidepdf.com/reader/full/sfs-weather-gard-may08 52/52
HeadquartersSpring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610610-376-5751 Fax: 610-376-8551
Manufacturing Plants
Exeter Plant Lincoln Corporate Center, 41 Dennis DriveReading, PA 19606
Medina Plant 5201 Portside DriveMedina, OH 44256
Wyomissing Plant Spring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610
U.S. Service Centers
Reading Service Center Spring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610
Durant Service Center PO Box 576, 500 West Third AvenueDurant, IA 52747
Houston Service Center 6120 West by Northwest Boulevard, Unit 160
Houston, TX 77040
Atlanta Service Center 675 Progress Center AvenueUnit MLawrenceville, GA 30043
Sacramento Service Center 2426 Port StreetWest Sacramento, CA 95691
Contact Us Toll Free: 1-800-234-4533 Fax: 1-888-485-4225Visit our website at www.sfsintecusa.com
Weather Gard Fastening Systems