Shop-Made Miter Clamps Woodworking Newsletter Vol. 7, Issue 1 - September 2012 1/5 www.leevalley.com *Editor’s note: In the photos showing the table saw, the blade guard has been removed for clarity. I try to be as self-sufficient as possible, so I like to manufacture my own tools whenever I can. I designed miter clamps that are simple to fabricate and require only scrap plywood and readily available hardware. For one clamp, you need a hardwood plywood scrap, a piece of 3/4” aluminum T-track, a 1/4” T-bolt, a star knob, a fender washer and a few screws. High-friction grip pads are optional. I suggest you use good quality 18mm (about 3/4”) thick Baltic birch plywood. This material is strong, smooth, and stable. It has very few voids and a nice, plain grain. After ensuring that your saw blade is perfectly perpendicular to the table saw top, cut the plywood into rectangular bases (according to the number of clamps you require), about 12” long x 10” wide each. Ensure that all four corners of each base are square. Measure your aluminum T-track (width and depth) precisely and mill dadoes lengthwise through the centers of the bases. Milling the Base The T-track should fit snugly in the dado and be just shy of the top face, as shown. Using such a track will prevent any glue from sticking to your clamps and will allow the clamping assembly to ride smoothly. The next step is to set your miter gauge at a precise 45° angle. A quick and effective method to do so is to place a framing square on the table saw, keeping the long side against the miter gauge. Pivot the miter gauge until the two inner 10” (or 12”) marks are in line with the same side of the miter gauge slot of the table saw (see arrows). Tighten the miter gauge to lock in a perfect 45° angle.
Transcript
Shop-Made Miter ClampsWoodworking Newsletter
Vol. 7, Issue 1 - September 2012
1/5 www.leevalley.com
*Editor’s note: In the photos showing the table saw, the blade guard has been removed for clarity.
I try to be as self-sufficient as possible, so I like to manufacture my own tools whenever I can. I designed miter clamps that are simple to fabricate and require only scrap plywood and readily available hardware.
For one clamp, you need a hardwood plywood scrap, a piece of 3/4” aluminum T-track, a 1/4” T-bolt, a star knob, a fender washer and a few screws. High-friction grip pads are optional. I suggest you use good quality 18mm (about 3/4”) thick Baltic birch plywood. This material is strong, smooth, and stable. It has very few voids and a nice, plain grain.
After ensuring that your saw blade is perfectly perpendicular to the table saw top, cut the plywood into rectangular bases (according to the number of clamps you require), about 12” long x 10” wide each. Ensure that all four corners of each base are square. Measure your aluminum T-track (width and depth) precisely and mill dadoes lengthwise through the centers of the bases.
Milling the Base
The T-track should fit snugly in the dado and be just shy of the top face, as shown. Using such a track will prevent any glue from sticking to your clamps and will allow the clamping assembly to ride smoothly.
The next step is to set your miter gauge at a precise 45° angle. A quick and effective method to do so is to place a framing square on the table saw, keeping the long side against the miter gauge. Pivot the miter gauge until the two inner 10” (or 12”) marks are in line with the same side of the miter gauge slot of the table saw (see arrows). Tighten the miter gauge to lock in a perfect 45° angle.
Shop-Made Miter ClampsWoodworking Newsletter
Vol. 7, Issue 1 - September 2012
2/4 www.leevalley.com
Before going any further, check if the face of your miter gauge is too slick. If it is, stick a strip of fine-grit sandpaper to it to prevent any creeping. When ready, clip the corners off. You must make sure that the cut will exactly kiss the outside corners of the dado. You may have to walk around your table saw to set the cut-line precisely.
When both cuts are done, you should have a perfect combined 90° angle. Check it with a framing square, as shown; achieving this angle is critical to the project’s success.
To cut the two remaining corners, you can use the rip fence. Once again, take your time when aligning the fence so that the saw blade will cut from the tip of the outside walls of the dado. If the corners are square, you won’t have to move the rip fence for the second cut.
Milling the Jaws
For each clamp you’re making, nail and clamp together two of the corner cut-offs, ensuring each side of the 90° corners are flush. These pieces will be part of your clamping assembly jaws.
To make additional jaws, either fixed or stationary, for your clamps, rip a strip of your plywood the same width as the combined base and stacked 90° clamp jaw. This should be 54mm, or approximately 2-1/4”.
Shop-Made Miter ClampsWoodworking Newsletter
Vol. 7, Issue 1 - September 2012
3/5 www.leevalley.com
For each clamp, two pairs of jaws are required. On one pair, cut both ends of each piece at 45°; on the other pair, cut one end of each piece at 45° and the other end square, as shown. Note the positioning of each jaw in the photo. On the bottom jaws, one of each of the 45° jaw ends is in line with the edge of the base side, while the other is 3/4’’ away from the corner of the dado. On the upper jaws, the 45° jaw ends are aligned with the walls of the dados, while the square ends are about 3-1/2’’ away from the backs of the adjacent lower jaws.
After gluing and nailing the jaws to the base edges, cut the aluminum T-track to length using a hacksaw. After this is done, drill and countersink holes in the T-tracks, if required. Keep in mind that upward force will be applied in use.
If your dadoes are tight, I suggest you use a plywood scrap and a hammer to drive the T-tracks down into the dadoes. This will ensure slick tracks for the sliding jaws to ride in. Use appropriate-sized wood screws to secure the T-tracks to the bases so that the sliding jaws won’t catch on the screw heads.
Shop-Made Miter ClampsWoodworking Newsletter
Vol. 7, Issue 1 - September 2012
4/5 www.leevalley.com
Place the sliding jaw tightly into the upper corner of the base as shown and make a pencil mark at the lower edge of the back of the jaw dead center in line with the center of the T-track (see arrow).
Transfer the center point onto the top of the jaw. Next use a center punch and a hammer to make a dent and then use a drill press to drill a 1/4’’ through hole. Repeat the process for each of your sliding jaws.
After sliding a T-bolt into the aluminum T-track, place the jaw onto the T-bolt and add a fender washer and a shop-made or store-bought star knob with a good grip. Your clamps are ready for use now, but you can go a step further.
You will get a better grip to secure the mitered pieces to be clamped if you add pieces of high-friction grip mat to two faces of your sliding jaws. Another option is to use strips of fine-grit sandpaper. If you use Baltic birch plywood, the edges are not too slick so this step is optional.
The Assembly
Shop-Made Miter ClampsWoodworking Newsletter
Vol. 7, Issue 1 - September 2012
5/5 www.leevalley.com
This photo shows a typical miter joint that has been glued. Since the glued joint sits just beyond the aluminum track, glue squeeze-out is not a problem. The joint can be left in the clamp while the glue dries or it can be nailed while in the clamp and then removed.
Shown here is a frame miter joint that has been glued using the other end of the clamp. It shows why the location of the fixed outside jaws is so important. Using this particular miter clamp, I can glue frames up to 3-1/2’’ wide and, once again, leave the clamp alone while the glue dries or nail it while temporarily secured.
One other option is to make the U-shaped bridge shown. This will enable you to use a bar clamp to apply more pressure if required until the star knob has been tightened. After removing it, you’ll be able to nail your joint, if necessary.
Here are two shop-made miter clamps ready for use. You may be tempted to add sandpaper or grip mats to the inside walls of the outer jaws, but I think they would interfere with adjusting the mitered pieces to be joined.
I found this project to be very satisfying. I hope you get as much satisfaction as I did if you make a few to use in your shop. Happy woodworking!
Text and photos by Serge Duclos
Serge Duclos started woodworking 40 years ago after purchasing a house. He soon found it was a way to relax from the stress related to his job as a human resources professional. Since retiring in 2004, Serge continues to enjoy his pastime and to update his bilingual woodworking blog http://atelierdubricoleur.wordpress.com with his projects, as well as his tips and techniques.
