Page 1 of 17
Sidho-Kanho-Birsha University Ranchi Road, P.O.- Sainik School
District - Purulia, PIN – 723104, W.B.
Phone : 03252- 202419 Website-www.skbu.ac.in
Ref No: FO/ 325 /SKBU/17 Date: 01/06/2017
E- Tender Notice
E- Tender are invited from reputed vendor or suppliers to supply the following office
furniture. Intending bidder may download the tender documents from the website
www.skbu.ac.in/www.wbtenders.gov.in. Only online tender documents will be
accepted. Last date of submission 22/06/2017 up to 2:00 PM, Date of Opening
24/06/2017 at 3 PM .
Terms & Condition:-
1. SKB University reserves the right to reject any or all tenders without assigning any
reason whatsoever.
2. No advance payment or payment against Performa invoice will be made. Payment
will be made after receipt, inspection, and installation/testing.
3. All damaged or unapproved goods shall be returned at the bidder’s risk and cost and
the incidental expenditure thereupon shall be recovered from the concerned party.
4. On acceptance of tender, the date of delivery should be strictly adhered to otherwise,
the SKB University reserves the right not to accept the delivery in full or in part. In case
the order is not executed within the stipulated period, the SKB University will be at
liberty to make purchases through other sources.
5. Payment of bill will be made through by crossed account payee Cheque or electronic
payment (NEFT) only after delivery and successful installation of each of the items.
6. Delivery Schedule: The Company shall be able to deliver the required items within
15 days of the receipt of order. Delivery/Installation is to be done at Purulia, West
Bengal.
7. Liquidated Damages : The Company shall be liable to indemnify the SKB University
in all respects and meet and pay off the litigation expenses and all the liabilities including
damages, sums etc. arising out of and as a consequence of the negligence, deficiencies,
mistakes, lapses, delays etc. in the execution of the various jobs and the services
provided.
8. Purchase Order: The purchase order for the entire quantity can be placed either in
one lump sum or as per the requirement through repeat order subject to availability of
Page 2 of 17
fund of the required items. The quantity shown is tentative and may increase or
decrease.
Annexure 1
Proforma For Techncial Bid
SL Particulars Information
1 Name of the Firm & Owner : (with Telephone/Mobile Numbers, email)
2 Type of Organisation (Proprietorship/Partnership/Pvt. Ltd./Limited Company) Month/Year of Establishment
3 Website of Bidder, if any
4 Month/Year of Establishment
5 PAN/Sales Tax/VAT Regd. Nos.
6 Annual Turnover 2016-17
7 Whether product(s) offered by the bidders are exactly as per the configuration of SKB University. If not, indicate the changes in each product
8 Clientele (submit copies)
9 Validity of Tender
10 Whether Terms & Conditions issued by SKB University are acceptable to the Firm
11 Whether Warranty as per the desired specification
** Bidder should only quote rate for 1 unit of each item in BOQ. Date Name: Signature of Owner/Authorized Representative Designation:
Page 3 of 17
Technical Specification Sl No Model Name Specifications UNIT
1
7 LEVER
ROUND
PADLOCK
Supply and placement with following specification 7 Lever round padlock
.Manufacturer should be a certified member of BIFMA for the last 10 years ,
SEFA-8 and should be following management systems as per ISO 9001:2015,
ISO 14001:2004, OHSAS 18001:2007 and energy management system as per
ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and
certification procedures for Design, Development, Manufacturing, Marketing,
Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture,
Accessories & Related Products and Provide Solutions for Home & Work Space
and should have Green Guard Certification for few of its products also should
have the service set up at least at district headquarter.
NOS
2
Aquaguard
Water Cooler
Cum Purifier
(AGCCP)
Supply and placement with following specification Aqua guard cooler cum
purifier Technical SpecificationsDimension:(H x D x W):700x430x460 mmRated
Voltage: 230 Volts, 50 Hz, ACWorking Voltage Range:180-260 VoltsPower
Rating: 550 Watts ± 10 % VCurrent Rating: 3 Amps MaxUV. Lamp Wattage: 8
WattsRated Compressor Capacty:910Kcal/hr±5%Water Cooling Capacity: 40
LPHWater Flow rates:0.666LPMWater Pressure:0.4 kg/cm²(Min.)Water
Pressure: 2.0kg/cm² (Max.)Max. Temp drop under standard test condition: 16.5°C
NOS
3 CHAIR FU 1007
Supply and placement with following specifications Overall Size : Depth - 59.5
cmWidth - 54.0 cm Height - 82.5 cm Seat Height- 46.0 cm Seat/ Back Assembly:
The seat and back are made from 1.0+/-0.1 cm. thick hot pressed moisture
resistant, commercial plywood measured as per QA method and upholstered with
PU foam and febric.Manufacturer should be a certified member of BIFMA for the
last 10 years , SEFA-8 and should be following managment systems as per ISO
9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management
system as per ISO 50001:2011 in accordance with the TÜV NORD CERT
auditing and certification procedures for Design, Development, Manufacturing,
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,
Furniture, Accessories & Related Products and Provide Solutions for Home &
Work Space and should have Green Guard Certification for few of its products
also should have the service set up at least at district headquarter.
NOS
4 CHAIR FU 7046
Supply and placement with following specifications Revolving chair The seat
made from 1.2cm. thk. hot pressed plywood and back is injection moulded from
black Co-polymer Polypropylene upholstered with fabric and moulded
Polyurethane foam together with seat and back covers. The back foam is designed
with contoured lumbar support for extra comfort. SEAT SIZE: 45.0cm(W) x
42.0cm.(D) BACK SIZE: 40.0cm(W) x 47.0cm.(H). The seat and back covers are
injection moulded in black Co-polymer Polypropylene. The polyurethane foam is
moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden
machine at 25% compression. The one-piece armrests are injection moulded from
black Nylon. The armrests are fitted to the seat with armrest connecting brackets
made of 0.5cm. thk. HR steel. Should have Permanent contact mechanism
designed with the features such as 360° revolving type, 14° maximum back-tilt
only, Upright position locking and Tilt tension adjustment. The pneumatic height
adjustment has an adjustment stroke of 9.0 cm. The bellow is 3 piece telescopic
type and injection moulded in black Polypropylene. The pedestal is injection
moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors
(castor wheel dia. 5.0cm.). The edestal is 57.0 cm. pitch-centre dia. (67.0 cm with
castors). The twin wheel castors are injection moulded in Black
Nylon.Manufacturer should be a certified member of BIFMA for the last 10 years
, SEFA-8 and should be following managment systems as per ISO 9001:2015,
ISO 14001:2004, OHSAS 18001:2007 and energy management system as per
ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and
certification procedures for Design, Development, Manufacturing, Marketing,
Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture,
Accessories & Related Products and Provide Solutions for Home & Work Space
and should have Green Guard Certification for few of its products also should
have the service set up at least at district headquarter.
NOS
Page 4 of 17
5 T-32
Supply of table of size 1199Wx590Dx750H with one drawer of size
355.5Wx559Dx167H having top made of prelaminated particle board of 18+/-
5mm thick with 2mm thick PVC edge banding on all sides and metal
understructure made of C frame made from 0.9+/-0.09mm thick powder coated
50 microns (+/-10) CRCA MS, tubular frame of dimesions 25.4+/-0.3mmX1.2+/-
0.096 mm thick MS ERW tube. The drawer should have 10 lever cam lock and
0.5+/-0.07mm thick CRCA MS shell and drawer tray and 0.8+/-0.1mm thick
CRCA MS drawer front and plastic handles. Manufacturer should be having
certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007
and should have Green Guard Certification for few of its products. and should
have the service set up at least at district headquarter
NOS
6
UNWIND CHAIR
WITH SS
FRAME
Supply and placement with following specifications with arm rest seat and back
and armrest are made up of injction moulded high impact strength polypropelene
polymer compound with indoor grade UV resistance. Overall size of the chair
should be 52.5cm width, 55.8cm depth, 84.5cm height and 45cm seat height. The
chair should be having MS powder coated welded tubular frame made of 2.22+/-
0.03cm X0.16+/-0.0128cm and 3.5+/-0.03cm x1.5+/-0.03X1.6+/-0.0128cm
MSRW tube, powder coated to DFT 50+/- 10 microns. The frame should be
provided with shoes made of high impact strength polypropelene polymer
compound with indoor grade UV resistance and should be press fiitted with
tubular frame.Manufacturer should be a certified member of BIFMA for the last
10 years , SEFA-8 and should be following managment systems as per ISO
9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management
system as per ISO 50001:2011 in accordance with the TÜV NORD CERT
auditing and certification procedures for Design, Development, Manufacturing,
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,
Furniture, Accessories & Related Products and Provide Solutions for Home &
Work Space and should have Green Guard Certification for few of its products
also should have the service set up at least at district headquarter.
NOS
7 FU L 43
Supply and placement with following specifications The premium lounge seating
system standing on beam with side frame assemblies . SIDE FRAME
ASSAMBLY : The side frame assembley is fitted to the two ends of the conecting
beam assembly to from the leg -cum armrest assembly . It is made of 3.81+-
0.3cm X0.2 +- 0.016 cm MS E.R.W tube and powder . the ends are fitted with
ABS moulded end caps. TIE MEMBER :- It is the connecting beam assy which
holds the two side frames each others 2 nos tie members are used to connect the
side frames . The tie members is made of 3.81+- 0.03 cm X 0.2 +- 0.016 cm .
thick MS E.R.W. tube and powder coated the seat/ back assemblies are mounted
on of the tie member which has 5.0+-0.1cm X0.5+-0.1cmthk long MS Std angels
welded to mount the seat and back. SEATREST ASSEMBLIY:- The seat rest
assembly consist of a fabricatted inner frame assembly insitu moulded high
resilience (HR) polyurethane foam having density =45+/- 2kg/m3 with hardness
load 25 +- kgf as per IS :7888 FOR 25% COMPRESSION OF THE FOAM . the
complete moulded seat rest assembly is covered with replaceble fabric uphlstry
cover. BACKREST ASSEMBLY:- The back rest assembly is flexing type and
consists of a fabricated inner frame assembly insitu -moulded with High
Resilience(HR)polyurethane foam having density = 45+/- 2 kg/m3 with hardness
load 14+- 2 kgf as per IS 7888 for 25% COMPRESSION OF THE FOAM . THE
COMPLETE MOULDED BACKREST ASSEMBLY IS COVERED WITH A
REPLACEBLE FABRIC UPHOLSTRY COVER..Manufacturer should be a
certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
Page 5 of 17
8 CHAIR FU 7212
Supply and placement with following specifications chair FU 7212 seat and back
made up of 1.2+/-0.1 cm thick hot pressed plywood, upholstered with fabric and
moulded Polyurethane foam with PVC lipping all around. The back foam should
be designed with contoured lumbar support for extra comfort. BACK SIZE:
49.5cm.(W) x 45.5cm.(H) SEAT SIZE: 49.5cm.(W) x 43.0cm.(D). The
polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20
+/- 2 on Hampden machine at 25% compression. The one piece armrest should be
made of black integral skin polyurethane with 50-70 shore hardness and
reinforced with MS insert. The armrests are scratch and weather resistant and
should be fitted to the seat with seat armrest connecting bracket made of 0.3+/-
0.022cm thick HR steel. The understructure should be a tubular frame of
cantilever type made of 2.54+/-0.03cm x0.2+/-0.16 cm thick MS ERW tube and
black powder coated. Manufacturer should be a certified member of BIFMA for
the last 10 years , SEFA-8 and should be following managment systems as per
ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management
system as per ISO 50001:2011 in accordance with the TÜV NORD CERT
auditing and certification procedures for Design, Development, Manufacturing,
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,
Furniture, Accessories & Related Products and Provide Solutions for Home &
Work Space and should have Green Guard Certification for few of its products
also should have the service set up at least at district headquarter.
NOS
9 FU 7201
Supply and placement with following specifications SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0..1 cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. * PCH-7201 (HIGH BACK) SIZE: 49.5cm. (W) X 69.5cm. (H) * 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+1-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests acre scratch and weather resistant. The armrests are fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel. 4. CENTRE PIVOT MECHANISM : The center pivot mechanism is designed with the following features: • 360° revolving type. • 17° ±2°maximum tilt on pivot at cerntre. • Tilt tension adjustment. • Upright position locking. 5. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. 6. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 7. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel. castors. The pedestal is 66.3 ±0.5cm.(76.3 ±1.0 cm with castors8. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon. Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
Page 6 of 17
10 ENTERPRISE
1500 TABLE
Supply and placement with following specifications TABLE ENTERPRISE
1500 table of size 1500 Wx 750D x 728H. Workspace Should be made of Pre
Laminated Particle Board (PLB) All work surface edges are duly sealed with
2mm thick PVC Edgebanding.Rectangular frameshould be Fabricated
component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy
polyester)LegFabricated component in 38mmx25mmx1.2mm thick MS ERW
Tube (IS:7138), Finish: Powder coat (Epoxy polyester). Manufacturer should be a
certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
11
TIME OUT 8
SEATER PU
COATED
Supply and placement with following specifications Overall Size : Depth –
2329.0 mm Width - 1175.0 mm Height – 750.0 mm Work Surface, PU Painted 25
mm Thick (+/- 1mm), Base Material- 25 mm MDF board. On top PU Painted of
minimum 2H hardness with 75% gloss as per color chart, combination color
graphics on the centre. Color as per color chart brown laminate on bottom.
Specially profiled edge for comfort. Understructure, bend pipe understructure of
MS powder coated. Pipe Dia. 38mm, 2mm thick. Understructure fitted with top
by MS machine screws.Legs, MS powder coated legs for PU top. 38 mm Dia.
Pipe legs are fixed with understructure and table top. Glide, Plastic glide fixed at
the understructure to prevent the damages of table top during stacking.
Manufacturer should be a certified member of BIFMA for the last 10 years ,
SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO
14001:2004, OHSAS 18001:2007 and energy management system as per ISO
50001:2011 in accordance with the TÜV NORD CERT auditing and certification
procedures for Design, Development, Manufacturing, Marketing, Sales, Supply
and Servicing of Home & Institutional, Interiors, Furniture, Accessories &
Related Products and Provide Solutions for Home & Work Space and should have
Green Guard Certification for few of its products also should have the service set
up at least at district headquarter.
NOS
12 NANO PERCH 3
STR CHAIR
Supply and placement with following specifications Nano Perch 3 seater
perforated chair Size: (163X57X67.5X40) cm with two arms & without cushion.
Cross Beam: It is made of black powder coated rectangular M.S. ERW Tube
having 8.0 +/- 0.03 cm x 4.0 +/- 0.03 cm x 0.2 +/- 0.014 cm size. leg & Armrestit
is chrome plated made of cold rolled steel with 0.12 +/- 0.013 cm thickness.
Seat/Back Shell: it is powder coated perforated shell made from cold rolled M.S.
sheet (DIN1623 Part1 ST-12 Grade) 0.14 +/- 0.013 cm thickness. The side bar is
made of chrome plated solid steel 3.0 +/- 0.03 cm x 1.2 +/- 0.3 cm with fluting
and plastic inserts. The shell is assembled on the cross beam with help of M8
bolts (per Seat- 8 nos, seat to bracket and 4 nos Bracket to cross Beam).
Manufacturer should be a certified member of BIFMA for the last 10 years ,
SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO
14001:2004, OHSAS 18001:2007 and energy management system as per ISO
50001:2011 in accordance with the TÜV NORD CERT auditing and certification
procedures for Design, Development, Manufacturing, Marketing, Sales, Supply
and Servicing of Home & Institutional, Interiors, Furniture, Accessories &
Related Products and Provide Solutions for Home & Work Space and should have
Green Guard Certification for few of its products also should have the service set
up at least at district headquarter.
NOS
Page 7 of 17
13 FINNESSE 4020
TABLE
Supply and placement with following specifications OF SIZE 1200X600X740
HAVING TOP AND SIDE PANELS MADE OF 25 MM THICK PLAIN
PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED
LAMINATE AND 1MM THICK BACKING LAMINATE (BDL)FLAT EDGE
DULY SEALED WITH 2MM THICK PVC BEADING AND HAVING
MODESTY PANEL IN FRONT MADE OF 18MM THICK PLAIN PARTICLE
BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE
(DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC
BEADING. Manufacturer should be a certified member of BIFMA for the last 10
years , SEFA-8 and should be following managment systems as per ISO
9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management
system as per ISO 50001:2011 in accordance with the TÜV NORD CERT
auditing and certification procedures for Design, Development, Manufacturing,
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,
Furniture, Accessories & Related Products and Provide Solutions for Home &
Work Space and should have Green Guard Certification for few of its products
also should have the service set up at least at district headquarter.
NOS
14 T-9
Supply and placement of Godrej make or equivalent as per design approve as per order Table of Size:- (1365 X 680 X 735) mm UNITISED OFFICE TABLES COLOUR SCHEME : COLOUR CODE TOP + UPPING STORAGE UNIT + HANDLES TOP FRAME + LEGS 05 Grey Shell : TA Grey Handle : Brown Drawers : TA Grey Char Brown 26 Ivory Shell : Char Brown Handle : Brown Drawers : Beige Char Brown 47 Rosewood Shell : her Brown Handle : Brown Drawers : Beige Char Brown 54 Teak Shell : Char Brown Handle : Brown Drawers : Beige Char Brown 55 Rosewood Shell : Olive Handle : Brown Drawers : Olive Char Brown 59 Bay Beech Shell : Black Handle : Brown Drawers.The Panels are made from 18 ± 0.5 mm thk Pre—laminated Boards as per with 2mm thick PVC Edge banding on all sides. *T-104 = 25 ± 0.5 mm Thick Pre—Laminated Board. Understructure: C-Frame Tubular Frame For T9 :Dia 25.4±0.3mm x 1.2±0.096mm Thk MS ERW tube. For others :Sq. 25.4±0.3mm x 1.2±0.096mm Thk MS ERW tube. Made from 1.0 ±0.09mm thk powder coated 50microns (±10) CRCA MS. Storage Shell : 0.5 ± 0.07 mm Thk CRCA MS. Drawer Tray : 0.5 ± 0.07 mm Thk CRCA MS. Drawer Front: 0.8 ± 0.1: mm Thk CRCA MS. Lock : 10 Lever Cam. Lock CONTP,r.v, CAP.. Handles : Built in Plastic. Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
Page 8 of 17
15
ANTI
VIABRATION
TABLE 600 D &
750 H
Supply and placement of as per design approve as per order Product size: back size 40 cm W X45 cm seat size 43 cm X 39 cm. The seat and back are made up of 1.2 cm thick hot pressed plywood upholstred with fabric and moulded polyurethane foam with PVC lipping allaround. The back foam is designed with contoured lumber support for extra comfort. High resilience (HR) polyurethane foam : The HR polyurethane foam is moulded with density =45=+/-2 kg/m3 and hardness load 16 +-2 kgf as per IS 7888 for 25%compression. Armrest The one piece armrests are injection moulded foam black co- polymer polypropylene. the armrest are fitted to the seat with armrest connecting brackets made of 0.5 cm thk HR steel. Permanent contact mechanism : The permanent contact mechanism is designed with the following features 360 degree revolving type 14 degree maximum back tilt only upright position locking tilt tension adjustment. Pneumatic height adjustment: The Pneumatic height adjustment has an adjustment stroke of 12 cm. Telescopic bellow assembly :- The bellow is 3 piece telescpic type and injuction moulded in black polypropylene. Pedestal assembly: The pedestal is injuction moulded in black 30% glass fitted nylon and fitted with 5 nos twin wheel castors. The pedestal is 61.0 cm pitch-center dia. (71.0cm with castors). twin wheel castors:- The twin castors are injection moulded in black nylon.Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
16
ANTI
VIABRATION
TABLE 900 D &
750 H
Supply and placement of as per design approve as per order Product size for antivibration table width 600 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing,
NOS
Page 9 of 17
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
17
ANTI
VIABRATION
TABLE 900 D &
900 H
Supply and placement of as per design approve as per order Product size for antivibration table width 900 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
Page 10 of 17
18
ANTI
VIABRATION
TABLE 900 D &
750 H
Supply and placement of Godrej make or equivalent as per design approve as per order Product size for antivibration table width 900 mm Depth 600 mm height 750 mm Tubular frame - Completely modular type tubular frame, which carries the load of kadappa and granite, kept on it. High-tension Pan head M6 Zinc black-coated screws (for better corrosion resistance) are used for the fastening. The material used is: 40Sq x 1.6 mm thick ERW tube and the overall load carrying capacity of tubular frame is 250 kgs of uniform distributed load. Cover Panels – They are 0.8 mm thick CRCA MS sheet and pre-treated and epoxy powder coated for better corrosion resistance. The thickness of powder coat is 45-50 microns which passes the test of Salt Spray for 1000 Hours and having the Scratch Hardness of 3 Kgs. Kadappa - 25mm thick Kadappa acts as the shock-dampening component. Work Surface – granite Vibration Isolating Rubber pads - The objective of using these rubber pads is to absorb the pulsating vibrations coming from the floor .The pads are made up from combination of nitrite rubber, cork particles and cross linked polyester fiber. This high-grade compound material possesses all the physical and mechanical properties required to minimize the dampening effect. Levelling screws - The Tubular frame has the provision for 4 height adjusters or Levelling Screws that take care of all levelling aspects. Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
Page 11 of 17
19 FU L 53 MIDAS
3 SEATER SOFA
Supply and placement with following specifications The Midas sofa is a lounge seating system standing on beam with side frame assemblies. It is available in three different models: 3-seater, 1. LH/RH SIDE FRAME: The LH/RH side frame is fitted to the two ends of the seat/back mounting frame to form the leg assembly. It is made of SS J4 Grade tube 0 4.44 cm. x 1.5mm thk. 2. SEAT/BACK MOUNTING FRAME: The seat/back mounting frame assy. holds the two side frames together. The mounting frames, 2nos are used to connect the side frames. The mounting frame is made of MS. E.R.W. tube 05.08±0.03cm. x 3.15±0.0252cm thk. black painted. The seat/back is mounted on 4.0±0.03cm x 2.0±0.02cm x 0.2±0.016cm thk M.S. rectangular tube which is welded on the beam of seat/back mounting frame. 3. SEAT/BACK ASSEMBLY: The seat/back assembly consists of 1.2±0.1cm thk plywood insert with Polyurethane foam having density = 45 +1- 2 Kg/m3 and hardness of the P. U. foam = 18 to 22 kg on Hampden m/c for 25% compression of the foam. The complete moulded seat/back assembly is covered with a replaceable fabric upholstery cover. *SEAT/BACK SIZE: 54.5 cm. (W)-x- 46.7cm. (D) x 12.5cm. (T) 4. BOTTOM SHOES: The side frames are fitted with front and rear bottom shoes made of injection moulded polypropylene. 5. FABRIC (VELVETINE PLUS): The sofa is upholstered with stain repellant "Velvetine plus" fabric as a standard offering. The velvet fabric can be vacuum cleaned in order to remove dirt & grit from the fabric surface. Upholstery covers made from Velvetine fabric should not be soap washed or dry cleaned.Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
Page 12 of 17
20 FU L52 MIDAS 2
SEATER SOFA
Supply and placement with following specifications The Midas sofa is a lounge seating system standing on beam with side frame assemblies. It is available in three different models: 2-seater, 1. LH/RH SIDE FRAME: The LH/RH side frame is fitted to the two ends of the seat/back mounting frame to form the leg assembly. It is made of SS J4 Grade tube 0 4.44 cm. x 1.5mm thk. 2. SEAT/BACK MOUNTING FRAME: The seat/back mounting frame assy. holds the two side frames together. The mounting frames, 2nos are used to connect the side frames. The mounting frame is made of MS. E.R.W. tube 05.08±0.03cm. x 3.15±0.0252cm thk. black painted. The seat/back is mounted on 4.0±0.03cm x 2.0±0.02cm x 0.2±0.016cm thk M.S. rectangular tube which is welded on the beam of seat/back mounting frame. 3. SEAT/BACK ASSEMBLY: The seat/back assembly consists of 1.2±0.1cm thk plywood insert with Polyurethane foam having density = 45 +1- 2 Kg/m3 and hardness of the P. U. foam = 18 to 22 kg on Hampden m/c for 25% compression of the foam. The complete moulded seat/back assembly is covered with a replaceable fabric upholstery cover. *SEAT/BACK SIZE: 54.5 cm. (W)-x- 46.7cm. (D) x 12.5cm. (T) 4. BOTTOM SHOES: The side frames are fitted with front and rear bottom shoes made of injection moulded polypropylene. 5. FABRIC (VELVETINE PLUS): The sofa is upholstered with stain repellant "Velvetine plus" fabric as a standard offering. The velvet fabric can be vacuum cleaned in order to remove dirt & grit from the fabric surface. Upholstery covers made from Velvetine fabric should not be soap washed or dry cleaned.Manufacturer should be a certified member of BIFMA for the last 10 years , SEFA-8 and should be following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
21 GLAZE COFFEE
TABLE
Supply and placement with following specifications TABLE LEGS
METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color :SILVER
POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE L
X W X T 1100 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS
TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS &
SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 6 MM Color : FULL
BLACK TEMPERED GLASS FINISHING: PARTIAL BLACK GLASS AND
SILVER POWDER COATING FRAME AND LEGS Manufacturer should be a
certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
Page 13 of 17
22 GLAZE
CORNER TABLE
Supply and placement with following specifications TABLE LEGS
METERIALS & SIZE : OVAL METAL TUBE THICK 1.5 mm Color :SILVER
POWER COATING TABLE TOP MATERIALS & SIZE : (DENSITY / TYPE L
X W X T 600 X 600 X 8 MM Color : PARTIAL BLACK TEMERED GLASS
TOP FULL BLACK TEMPERED GLASS TABLE BOTTOM MATERIALS &
SIZE : (DENSITY / TYPE) L X W X T 1100 X 600 X 6 MM Color : FULL
BLACK TEMPERED GLASS FINISHING: PARTIAL BLACK GLASS AND
SILVER POWDER COATING FRAME AND LEGS Manufacturer should be a
certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
23 REFRIGERATOR Supply and placement with following refrigetor RD EDGE PRO 190 CT 5.2
LUSHWINE NOS
24 COMPUTER
TABLE C-9
Supply and placement with following specifications computer table companion
C9 with overall size 900 X 500X 750 mm (WXDXH).Manufacturer should be a
certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
25 FLOYED
SINGLE BED
Supply and placement with following Specification for FLOYD BED Overall
Size: Width - 2036.0 mm Depth - 958.0 mm Height - 746.0 mm Material Body
panels are made of 18 mm thick Prelaminated Particle Board All the exposed
edges are edge banded with 2 mm thick PVC edge banding Bed structure consist
of metal frames made of M.S. 25 mm Square Pipes in 1.2 mm Thickness.
Hardware :The high quality hardware used Construction: Knock Down
construction. Finish: 18 mm thick Prelaminated Particle Board is in VALIGNY
OAK make – GODREJ (SHIRVAL). Metal frames are powder coated in shade
PANTONE S/G 410C to thickness of 50 microns (+-10). .Manufacturer should
be a certified member of BIFMA for the last 10 years , SEFA-8 and should be
following managment systems as per ISO 9001:2015, ISO 14001:2004, OHSAS
18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
26
SONATA
MATTRESS
78*36*3
Supply and placement with following specifications Overall Size : Length -
1981.0 mm Depth - 914.0 mm Thickness – 3 Inch RC Pad Thickness:- 9 mm RC
pad density :- 70 gm/dcm3 DRC centrifuged:- 20 % EPE sheet thickness :- 75
mm EPE sheet density :- 23 gm/dcm3 Quilting Foam Thickness :- 10 mm
Quilting Foam Density :- 18 gm/dcm3 Tapestry :- 80 gm Tapestry Nature:-
PolyCotton. The .Manufacturer should be a certified member of BIFMA for the
last 10 years , SEFA-8 and should be following managment systems as per ISO
9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management
system as per ISO 50001:2011 in accordance with the TÜV NORD CERT
auditing and certification procedures for Design, Development, Manufacturing,
Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors,
Furniture, Accessories & Related Products and Provide Solutions for Home &
Work Space and should have Green Guard Certification for few of its products
also should have the service set up at least at district headquarter.
NOS
Page 14 of 17
27 TABLE T-101
Supply and placement with following specifications overall size w 1199 d 590 h
750 top worksurface the panels are made from 18+- 0.5 mm thk pre-laminated
boards as per with 2mm thick pvc edge banding on all sides made from 0.9 +- 0.9
mm thk powder coated 50 micrones CRCA MS. lock :- shell 0.5 +- 0.07 mm thk
CRCA MS drawer tray: 0.5 +- 0.07 mmthk CRCA MS drawer front 0.8 +-0.1 mm
thk CRCA MS lock 10 lever cam lock handles built in plastic.Manufacturer
should be a certified member of BIFMA for the last 10 years , SEFA-8 and should
be following managment systems as per ISO 9001:2015, ISO 14001:2004,
OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
28
STOREWEL
PLAIN
ALMIRAH
Supply and placement of Godrej make or equivalent as per design approve as per
order Storewel Plain Almirah 1. Models Plain with 4S2. Product Size: Plain (4S) - 916 mm (W) x 486 mm (D) x 1981 mm (H) DMX Drg.- ST-095, Rev.0 3. Construction & Material Welded construction.0.8 mm thk CRCA for Back, Shelf & 0.9 mm thk CRCA for all other components. 4. Configuration (Door) Full height Steel Hinged Door5. Locking & handle : Mazak Handle 3 way locking mechanism with shooting bolt arrangement.6. Shelving : Height wise Adjustable Shelf Mounting Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum Plain 4S : 4 Nos. of Adjustable Full Shelves. 7. Leveler M10 Screw type leveler with hex plastic base 8. Finish Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Manufacturer should be a certified member of BIFMA,
SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
29 GLASS DOOR
STOREWEL
Supply and placement with following specifications of Glass door strewel1.
Product Size: 915 mm (W) x 486mm (D) x 1981* mm (H) *- Height without
leveler. 2. Construction & Material § Welded construction.§ 0.8 mm thk CRCA
for Shelf & 0.9 mm thk CRCA for all other components. 3. Door • Glasses fitted
to full height steel frame. 4. Locking • 2 way locking mechanism with shooting
bolt. 5. Handle : • Chrome plated brass handle 6. Shelving : • Height wise
Adjustable Shelves 4 Nos. • Uniformly Distributed Load Capacity per full shelf is
80 Kg maximum 7. Leveler § M10 Screw type leveler with hex plastic base. (add
10mm to unit height and additional 10mm for adjustment.) 8. Finish § Epoxy
Polyester Powder coated to the thickness of 50 microns (+/-10). Manufacturer
should be a certified member of BIFMA for the last 10 years , SEFA-8 and should
be following managment systems as per ISO 9001:2015, ISO 14001:2004,
OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
Page 15 of 17
30 4 DOOR VFC
Supply and placement with following specifications Models & Product Size 4
Drawer Width: 470mm Height: 1320mm Depth: 620mm Construction:Rigid
Knock Down Construction Material: CRCA 0.7 mm Thick (Top, Side & Drawer
Front); 0.6 mm Thick (Frames, Drawer- Inside Cover, Side Back Side) 0.5mm
Thick (Back, Bottom, Drawer Bottom) Drawer front: Easy to grip Full length
Handle recess integrated into Metal Drawer fronts Label Holder Snap on type
plastic label holder on Drawer Front Drawer Size & Files type For hanging ‘Ezee’
/ ‘Visa’ files (Foolscap) from front to back (Files Along theWidth) No. of 20 mm
thk file which can be hanged in above way per drawer is 28. Locking & anti-
tipping arrangement Centralized locking with 10 lever Cam Lock & having anti-
tipping arrangement to ensure thatwhen one drawer is opened for use, it does
notallow other drawers to be opened. Slide High quality precision ball slide.
Drawer Load: 40 kg. UDL for 75,000 cycles (BS) Triangular Plate Plain
Triangular plate pop riveted at the bottom corners for rigidity.Finish:Epoxy
Polyester Powder coated to the thickness of 50 microns (+/-10)Manufacturer
should be a certified member of BIFMA for the last 10 years , SEFA-8 and should
be following managment systems as per ISO 9001:2015, ISO 14001:2004,
OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in
accordance with the TÜV NORD CERT auditing and certification procedures for
Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of
Home & Institutional, Interiors, Furniture, Accessories & Related Products and
Provide Solutions for Home & Work Space and should have Green Guard
Certification for few of its products also should have the service set up at least at
district headquarter.
NOS
31 IMPRESS
TABLE
Supply and placement of Godrej make or equivalent as per design approve as per
order Impress Table MAIN TOP MDF + VENEER + PU Coating , Size : 1800 W *900D*750 H TOP THICKNESS – 65 mm MODESTY size : 1640 X 600 X16 MM MDF + Veneer + PU Coating MOBILE PEDESTAL MDF + Veneer + PU Coating , Size : 510W* 635H * 445D mm MDF + VENEER + PU Coating, Size : 1200W x 445D x 660 H TOP THICKNESS – 25 mm Manufacturer should be a certified member of
BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
32 4 DOOR
BOOKCASE
Supply and placement of Godrej make or equivalent as per design approve as per order 4 door bookcase. Product size for 4 door bookcase 914mm W 320 mm D 1742 mm H Construction & material: Rigid knock Down construction. Top panel side panel and back panel are made from 0.7 mm high yield strength CRCA , rest in 0.8 mm CRCA. Configuration 4 door. Door Features / locking:- Each door has 6 lever cam lock with common key. Each door has 3mm thk transparent glass for clear inside vision secured in a metal frame through rubber gasket. Each door has a scissor mechanism for receding inside the top of respective compartment & ensure parallel & smooth movement. Each door has plastic side end caps as handel which is easy to grip. Behind Storage shelving:- Each compartment has storage shelf. Uniformly Distributed load capacity per each shelf is 80 kg maximum. Top Panel:- 4 door has inside metal top panel. Finish Epoxy polyester powder coated to the thickness of 50 micrones.(+/-10) Manufacturer should be a certified member of BIFMA, SEFA-8 and should be following management systems as per ISO 9001:2015, ISO 14001:2004, OHSAS 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design,
NOS
Page 16 of 17
Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
33 FU7001 D
Supply and placement of Godrej make as per order High back Revolving Chair to
the following specification 1) SEAT/BACK ASSEMBLY: The seat / back are
made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and
moulded Polyurethane foam together with moulded seat and back covers. The
back foam is designed with contoured lumbar support for extra comfort. The chair
is available in four models. PCH-7001D (HIGH BACK) SIZE: 50.0cm. (W) X
72.0cm. (H) SEAT SIZE: 50.0cm. (W) X 46.0cm. (D) 2) POLYURETHANE
FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and
Hardness = 20 +/- 2 on Hampden machine at 25% compression. 3) SEAT /
BACK COVERS: For PCH-7001D the seat cover is injection moulded in black
co-polymer polypropylene and back cover is vacuum formed from ABS sheets.
4) ARMRESTS (for PCH-7001D): The one-piece armrests made of black integral
skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert.
The armrests are scratch and weather resistant. The armrests are fitted to the seat
with seat/armrest connecting strip assembly made of 0.5cm. thk. HR steel. 5A)
CENTRE PIVOT MECHANISM (for PCH-7001D): The center pivot mechanism
is designed with the following features: 3600 revolving type. 17° maximum tilt on
pivot at center. Tilt tension adjustment. Upright locking. 6) PNEUMATIC
HEIGHT ADJUSTMENT(for PCH-7001D): The pneumatic height adjustment
has an adjustment stroke of 12.0 cm. 7) TELESCOPIC BELLOW
ASSEMBLY(for PCH-7001D): The bellow is 3 piece telescopic type and
injection moulded in black Polypropylene. 8) PEDESTAL ASSEMBLY(for
PCH-7001D): The pedestal is injection moulded in black 30% glass-filled Nylon
and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm. pitch-center dia.
(76.0 cm with castors). 9) TWIN WHEEL CASTORS(for PCH-7001D): The twin
wheel castors are injection moulded in 30% Glass Filled black Nylon.
Manufacturer should be a certified member of BIFMA and should be following
managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007
and energy management system as per ISO 50001:2011 in accordance with the
TÜV NORD CERT auditing and certification procedures for Design,
Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home
& Institutional, Interiors, Furniture, Accessories & Related Products and Provide
Solutions for Home & Work Space and should have Green Guard Certification
for few of its products also should have the service set up at least at district
headquarter.
NOS
Page 17 of 17
34 WORKSTATION
750X600
Supply and place of Godrej Make or equivalent workstation System offered- Tile based 'Spacio Plus'. panel thickness- 50 MM (APPROX), HT. - 1200 MM( APPROX), TILE CONFIGURATION FOR ALL PANELS : ABOVE WORKTOP LEVEL : FAB. MAGNETIC TILE, BELOW WORKTOP LEVEL :METAL, FIN- PRELAMINATE, RACEWAY - FOR MOUNTING OF SWITCHES : 150MM METAL RACEWAY AT SKIRTING LEVEL FOR ALL PANELS & INTEWRMEDIATE RACEWAY AT below WORKTOP LEVEL, WORKSURFACE : IN PRELAMINATED PARTICLE BOARD AND PVC LIPPING; BOARD THK. - 25MM & OF DIMENSIONS : RECTA - 750 MM X 600 MM D - 1 NOS, Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
RUNNING
FEET
35 KBPT
Supply and place of Godrej Make or equivalent METAL KBPT with channel system. Manufacturer should be a certified member of BIFMA and should be following managment systems as per ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and energy management system as per ISO 50001:2011 in accordance with the TÜV NORD CERT auditing and certification procedures for Design, Development, Manufacturing, Marketing, Sales, Supply and Servicing of Home & Institutional, Interiors, Furniture, Accessories & Related Products and Provide Solutions for Home & Work Space and should have Green Guard Certification for few of its products also should have the service set up at least at district headquarter.
NOS
36 ROLLER
BLINDS
Supply and placement with following roller blinds Sq. Ft