SIGN ANDDISPLAYADHESIVESELECTIONGUIDE
Offering the latest in adhesive
technologies required to bond
the wide range of substrates
typically found within the
Sign and Display market.
Science + Innovation= SMARTER ADHESIVE SOLUTIONS
ADHESIVES FOR PLASTICS DescriptionProduct
Non-flammable, water thin, very fast-setting solventcement for acrylic. Will also bond styrene, butyrate and polycarbonate to themselves.
3
Non-flammable, water thin, fast-setting solventcement for acrylic. Will also bond styrene, butyrate and polycarbonate to themselves.
4-SC
Two-component Kit, high strength, high viscosity structural adhesive for bonding large parts of, PVC, acrylic, ABS, and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.
10
Medium bodied, fast-setting, high strength acrylic (PMMA) cement. Will also bond styrene, butyrate, polycarbonate, other plastics and porous surfaces.
16
Two-component Kit, reactive, high strength adhesive for bonding and fabricating all acrylics (extruded, cast, and cross linked PMMA) to each other. It will also bond acrylic to polyester, butyrate, PVC, ABS, PETG.
40
Two-component 10:1, reactive, high strength acrylic based adhesive provides ‘‘museum quality’’ water clear joints with excellent weather ability. Mil Spec A-8576C Type III.
42
VOC-free 1:1, two-component, slow-setting, reactive,urethane-based adhesive for bonding polycarbonate,butyrate, ABS, and PETG to themselves and each other. Excellent UV light resistance.
55
VOC-free 1:1, two-component, fast-setting, reactive,urethane-based adhesive for bonding polycarbonate,butyrate, ABS, and PETG to themselves and each other. Excellent UV light resistance.
58
DescriptionProduct
High Viscosity ethyl based ‘superglue’ for bonding where gap fill is important, or on absorbent surfaces such as wood, paper and some fabrics. Bonds most plastics, rubbers and metals.
CA01
A thixotropic ‘superglue’ gel. It is a non-drip formulation and will not run on vertical surfaces. It is fast to set on difficult surfaces such as leather and acetic substrates.
CA44
Thixotropic UV adhesive for bonding clear plastics to themselves, glass and metal. High Intensity Visible light cure is also possible.
UV106
Low odour 1:1, toughened clear acrylic adhesive. Bonds clear plastics, and other dissimilar materials. Low exotherm and shrinkage allow bonding of Alucabond without witness marks on face of panel.
3004-03
Low viscosity ‘superglue’ for use with special primer for bonding difficult plastics and elastomers such as PP, PE, Silicone, Glass-filled Nylon.
CA4061 Kit
Two-component 10:1 ‘Ultimate Plastic Bonder’ for bonding Polyolefin’s (P.P. & P.E.) to themselves, most other plastics and metals.
PPX5
Medium syrup, fast set, flexible bond. For flexible orrigid vinyl to itself or other materials such as leather,canvas, fabrics, ABS, acrylics, butyrate and polyurethane. Weather resistant.
4784
Low VOC, medium bodied, fast setting, cement for bonding ABS only.4707
www.scigrip.com
CHANGING THE WAY YOU PUT THINGSTOGETHER
SCIGRIP Smarter Adhesive Solutions™, is one of Europe’s leading manufacturers and formulators
of Engineering and Structural adhesives. Many of our patented formulations are used within the
automotive, marine and OEM sectorsaround the world.
The Sign and Display offer focuses on the adhesive technologies required to bond the wide range
of substrates typically found within the Sign and Display, shopfitting and plastic assembly markets.
Our 20 years’ experience in this market is based on the supply of quality products with first class
logistical and technical support.
Due to many potential variations in substrate and surface chemistries, SCIGRIP Adhesives and its distributors recommend that all substrates be tested under the intended applications to determine suitability.
SIGN AND DISPLAY SELECTION GUIDE
5558
4707
1642
165558
16425558
101645
45164245
423004
PPX5500010
30010
30010
30010
30010
30010
30041042
4547845558
5000-065000-065000-065000-06
1642
34SC1642
UV1061642
4245
1642
45164245
423004
PPX51045
1045
1045
1045
1045
1045
UV1063004
4245
45 4784Acrylic Sheet
ABS
5000-065000-065000-065000-06
165558
UV1061642
34SC4255
425558
101642
45164245
423004
PPX51045
1045
1045
1045
1045
1045
UV1063004
104245
45 10PETG
5000-065000-065000-065000-06
16425558
4245
425558
4SC42
101642
45164245
423004
PPX51045
1045
1045
1045
1045
104245
UV1063004
104245
45 10Polycarb
5000-065000-065000-065000-06
10164245
1642
101642
101642
1042
45164245
423004
PPX5500045
3001045
3001045
3001045
3001045
3001045
30042002
1042
45 4784PVC (Rigid)
5000-065000-065000-065000-06
165558
UV1061642
34255
425558
101642
45164245
3004 PPX51045
1045
1045
1045
1045
1045
UV1063004
104245
45 10PVC (Flexible)
5000-065000-065000-065000-06
45 45 45 45 4545
478445 3004 PPX5 45 45 45 45 45 45
20023004
45 45478445
PVC (Foam)
5000-065000-065000-065000-06
423004
423004
423004
423004
1042
3004
103004
103004
1042
3004
4245
PPX5
4245300
4245300
4245300
4245300
4245300
30043346
300420023346
300445
20023004Alucobond™
5000-065000-065000-065000-06
PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5PE/PP
5000-065000-065000-065000-06
105000
1045
1045
1045
500045
1045
1045
3004 PPX53005000
3005000
3005000
3005000
3005000
3005000
UV1063004
33462002
45 10Fibreglass
(GRP)
5000-065000-065000-065000-06
30010
1045
1045
1045
3001045
1045
1045
32953004 PPX5
3005000
30032953346
30032953346
30032953346
30032953346
30032953346
33462002
1045
1045
10Aluminium
5000-065000-065000-065000-06
30010
1045
1045
1045
3001045
1045
1045
32953004 PPX5
3005000
30032953346
30032953346
30032953346
30032953346
30032953346
33462002
1045
1045
10Stainless Steel
5000-065000-065000-065000-06
30010
1045
1045
1045
3001045
1045
1045
32953004 PPX5
3005000
30032953346
30032953346
30032953346
30032953346
30032953346
33462002
1045
1045
10Mild Steel
5000-065000-065000-065000-06
30010
1045
1045
425558
3003295
1045
164245
3004 PPX53005000
30032953346
30032953346
30032953346
30032953346
30032953346
33462002
1045
1045
10Brass Sheet
5000-065000-065000-065000-06
30010
1045
1045
1045
3001045
1045
1045
3295
30043346
PPX53005000
30032953346
30032953346
30032953346
30032953346
30032953346
33462002
1045
1045
10PowderCoated
5000-065000-065000-065000-06
3004UV1063004
UV1063004
UV1063004
30042002
30042002
30042002
300420023346
PPX533462002
33462002
33462002
33462002
33462002
33462002
33462002
33462002
2002 2002Glass
5000-065000-065000-065000-06
1042
1042
UV1063004
UV1063004
30042002
30042002
30042002
30042002
PPX51045
1045
1045
1045
1045
1045
33462002
33462002
200210
2002Polyester
5000-065000-065000-065000-06
45 45 45 45 45 454510
453004
PPX5 451045
1045
1045
1045
1045
20021045
45 45Wood
5000-065000-065000-065000-06
47845558
4784 10 10 4784478445
4784 3004 PPX5 10 10 10 10 10 10 2002 10 4547845558
Polyurethane
ABS
PETG
Poly
ca
rb
PVC
(R
igid
)
PVC
(Fl
exi
ble
)
PVC
(Fo
am
)
Alu
co
bo
nd
™
PE/P
P
Fib
reg
lass
(G
RB)
Alu
min
ium
Sta
inle
ss S
tee
l
Mild
Ste
el
Bra
ss S
he
et
Pow
de
r Co
ate
d
Gla
ss
Poly
est
er
Wo
od
Poly
ure
tha
ne
Ac
rylic
Sh
ee
t
SCIGRIP Changing the way you put things together.
ADHESIVES FOR METALSDescriptionProduct
Two-component Kit, high strength, high viscosity structural adhesive for bonding PVC, acrylic, ABS, and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.
10
Two-component 4:1, high strength, high viscosity,reactive structural adhesive for bonding unprepared and corrosion resistant metals, composites, wood, and plastics.
45
Two-component 10:1 MMA for bonding metals &composites. Most metals do not require a primer or surface preparation. Reduced odour and low read-through.
300 Series
A high specification clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.
2002
High Strength 1:1, low viscosity Toughened Acrylicbased adhesive. May be applied bead-on-bead or via mixer nozzle. Ideal for close fitting or ‘discrete’ bonds in stainless steel, aluminium and other metals.
3295-03
DescriptionProduct
No Mix System, Rubber Toughened Acrylic adhesive for use with brush on 7701 Initiator. Allows infinitely adjustable open time, but very rapid fixture on assembly.
3346 Kit
Low odour 1:1, toughened clear acrylic adhesive. Bonds clear plastics, and other dissimilar materials. Low exotherm and shrinkage allow bonding of Alucabond without witness marks on face of panel.
3004-03
High strength, two-component 1:1 MMA for bondingmetals, plastics and composites. Good gap-filling and low sag properties for a wide range of applications. Excellent tensile and impact strength.
5000 Series
A clear, two-component 1:1, non-yellowing, fast curing epoxy adhesive. This diverse adhesive can join a huge array of different materials, providing a high strength, water resistant bond.
6005
DescriptionProduct
High strength two-component 1:1 MMA for bonding metals, plastics and composites. Good gap-fi lling and low sag properties for a wide range of applications. Excellent tensile and impact strength.
5000 Series
Two-component 10:1 MMA for bonding metals &composites. Most metals do not require a primer or surface preparation. Reduced odour and low read-through.
300 Series
Low odour 1:1, toughened clear acrylic adhesive. Bonds clear plastics, and other dissimilar materials. Low exotherm and shrinkage allow bonding of Alucabond without witness marks on face of panel.
3004-03
DescriptionProduct
Two-component Kit, high strength, high viscositystructural adhesive for bonding PVC, acrylic, ABS,and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.
10
A clear, two-component 1:1, non-yellowing, fast curing epoxy adhesive. This diverse adhesive can join a huge array of different materials, providing a high strength, water resistant bond.
6005
A high specifi cation clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.
2002
ADHESIVES FOR COMPOSITES
ADHESIVES FOR GLASSDescriptionProduct
No Mix System, Rubber Toughened Acrylic adhesive for use with brush on 7701 Initiator. Allows infi nitely adjustable open time, but very rapid fi xture on assembly.
3346 Kit
Low odour 1:1, toughened clear acrylic adhesive. Bonds clear plastics, and other dissimilar materials. Low exotherm and shrinkage allow bonding of Alucabond without witness marks on face of panel.
3004-03
DescriptionProduct
Thixotropic UV adhesive for bonding clear plastics tothemselves, glass and metal. High Intensity Visible light cure is also possible.
UV106
A high specification clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.
2002
CLEANERS, PRIMERS AND INITIATORSDescriptionProduct
Used in combination with CA4061 or other ‘superglue’ to promote adhesion on low energy surfaces such as Polyethylene, Polypropylene, Silicone rubber and certain hard to bond materials.
A701
A non-flammable, solventless initiator to be used in conjunction with our 3346 No-mix acrylic adhesive. 7701 ensures a rapid fi xture time once parts are assembled and is also available in a slower version - 7705.
7701
DescriptionProduct
A multi-purpose plastics cleaner for acrylics,polycarbonate, butyrate, vinyl, ABS, Styrene.
Powerful Solvent Cleaner/Degreaser.A061
57
Other products available on request
ViscosityReference
Typicalviscosity (cps)
Typicalspecificgravity
WorkingTime
PackagingProduct ColourTechnologyFixtureTime
N/A1.302 min1 min1 Litre Tin#ClearAcrylic3 water-thin
N/A1.123 min1-2 min1 Litre Tin#ClearSolvent4SC water-thin
40,0001.031-2 hrs25 min473ml Kit#WhiteMMA10 ketchup
1,0001.035-6 min2-3 min473ml Tin#ClearAcrylic16 motor oil
2,9001.032 hrs20 min473ml Kit#ClearMMA40 syrup
2,9001.032 hrs15 min50ml Cart#ClearAcrylic42 syrup
4,0001.141-2 hrs5-6 min50ml Cart#ClearUrethane55 syrup
4,0001.1420 min2-3 min50ml Cart#ClearUrethane58 syrup
1,5001.0660 sec10 sec50g Bottle#ClearCyanoacrylateCA01 motor oil
50,0001.0660 sec10 sec20g TubeClearCyanoacrylateCA44 gel
5,0001.09< 30 secN/A50ml Bottle#ClearAcrylic - UV Cureduv106 syrup
25,0000.99< 5 min< 3 min50ml Cart#ClearToughened Acrylic3004-03 gel
201.062 secsN/A20g Bottle#ClearCyanoacrylateCA4061 KIT water-thin
6,5000.99> 15 min4-6 min50ml Cart#WhiteMMAPPX5 syrup
3350.9025-30 min20 min473ml Tin#ClearSolvent4784 motor oil
4,0000.8810-15 min10 min473ml Tin#MilkySolvent4707 syrup
ViscosityReference
Typicalviscosity (cps)
Typicalspecificgravity
WorkingTime
PackagingProduct ColourTechnologyFixtureTime
40,0001.031-2 hrs25 min473ml Kit#WhiteMMA10 ketchup
500,0001.0515 min6 min400ml Cart#TanMMA45 peanut butter
250,0001.02VariousVarious50ml & 490mlOff White•MMA300 Series peanut butter
N/AN/A24 hrs20 min290ml CartClearMS Polymer2002 mastic
3,5001.026 min2 min25ml, 50ml#Pink & GreenToughened Acrylic3295-03 syrup
30,000N/A< 90 sec< 30 sec300ml Tube#ClearToughened Acrylic3346 Kit N/A
120,0000.97VariousVarious25ml, 50ml & 400mlAmberMMA5000 Series peanut butter
50,0001.210-12 min3-4 min50ml CartClearEpoxy6005 syrup
ViscosityReference
Typicalviscosity (cps)
Typicalspecificgravity
WorkingTime
PackagingProduct ColourTechnologyFixtureTime
30,0001.04< 90 sec< 30 sec300ml Tube#Pale AmberToughened Acrylic3346 Kit ketchup
25,0000.99< 5 min< 3 min50ml Cart#ClearToughened Acrylic3004-03 gel
5,0001.09< 30 secN/A50ml Bottle#ClearAcrylic - UV CuredUV106 syrup
N/AN/A24 hrs20 min290mlClearMS Polymer2002 mastic
ViscosityReference
Typicalviscosity (cps)
Typicalspecificgravity
WorkingTime
PackagingProduct ColourTechnologyFixtureTime
N/AN/AN/AN/A400ml AerosolClearCleaner/DegreaserA061 water-thin
N/A0.81N/AN/A500ml Tin#ClearPlastic Cleaner57 water-thin
N/AN/AN/AN/A50ml Pump SprayClearCA PrimerA701 water-thin
N/AN/A< 2 min< 1 min18ml & 35ml Bottle#Clear3346 Initiator7701 water-thin
ViscosityReference
Typicalviscosity (cps)
Typicalspecificgravity
WorkingTime
PackagingProduct ColourTechnologyFixtureTime
120,0000.97VariousVarious25ml, 50ml & 400AmberMMA5000 Series peanut butter
250,0001.02VariousVarious50ml & 490mlOff White•MMA300 Series peanut butter
25,0000.99< 5 min< 3 min50ml Cart#ClearToughened Acrylic3004-03 gel
40,0001.031-2 hrs25 min473ml Kit#WhiteMMA10 ketchup
50,0001.210-12 min3-4 min50ml CartClearEpoxy6005 syrup
N/AN/A24 hrs20 min290ml CartClearMS Polymer2002 mastic
# Other pack sizes are available please enquire • Also available in black
© 2012 - SCIGRIP® Smarter Adhesive Solutions. All rights reserved.
SCIGRIP EuropeUnit 22, Bentall Business Park, Glover Road,Washington, Tyne and Wear, NE37 3JD. United KingdomTel: +44 (0) 191 419 6444Fax: +44 (0) 191 419 6445Email: [email protected]
www.scigrip.com
Your distributor:The information contained herein is produced in good faith, and is believed to be reliable but is for guidance
only. SCIGRIP and its agents cannot assume liability or responsibility for results obtained in the use of its products
by persons whose methods are outside or beyond our control. All advice is given subject to terms & conditions of
sale, which are available on request from SCIGRIP. It is the users responsibility to determine the suitability of any of
the products and methods of use or preparation prior to use mentioned in our literature and furthermore it is the
user’s responsibility to observe and adopt such precautions as may be advisable for the protection of personnel
and property in the handling and use of any of our products. SCIGRIP reserves the right to change specifications
& prices without notice and customers should satisfy themselves that information relied on by the customer is that
which is currently published by the company on its website.
FURTHER SMARTER ADHESIVE SOLUTIONS AVAILABLE FROM SCIGRIP:
SCIGRIP’s well established range of REACH compliant engineering, maintenance, adhesives and sealants has grown and developed with the OEM and MRO industrial sectors over the past 3 decades. This division is a highly accredited sector of the SCIGRIP European Group, with WRAS, AGA, ASTM, NSF, DVGW, MIL specifications available for many of the products.
THE RANGE INCLUDES;
• ANAEROBICS - THREADLOCKERS - RETAINERS - SEALANTS & GASKET MAKERS• CA-INSTANT ADHESIVES• RTV SILICONES - POWERCAN PACKAGING• EPOXY STICKS AND REPAIR COMPOUND• ACTIVATORS AND PRIMERS• UV ADHESIVES
SCIGRIP offers cutting edge formulations of Methacrylate adhesives that are unrivalled for their combination of strength, toughness and ease of use.
This highly accredited range of products successfully services the Marine, Transportation, Building & Construction, Renewable Energy and Recreational Vehicle sectors.
THE RANGE COVERS;
• VARIED OPEN TIMES• 0.5MM - 39MM GAP FILL• PRIMERLESS METAL BONDING• CLEAR MMA• PE AND PP BONDING• HIGH PEEL AND HIGH FATIGUE RESISTANCE• HIGH TOUGHNESS AND ELONGATION• MARINE APPROVALS
HOLDTITE ENGINEERING STRUCTURAL ADHESIVES
S&D03/12