JL18FBSSINS - REV 6 6/8/2020 Page 1
JEEP JL SIGNATURE FRONT BUMPERS
SIGNATURE SERIES
JL
*VERIFY YOU HAVE ALL THE COMPONENTS BEFORE STARTING THE INSTALLATION. REFER TO THE ENGINEERING DRAWINGS AT THE END OF THIS DOCUMENT FOR A COMPLETE PARTS LIST*
WEB LINK: http://lodoffroad.com/assets/pdfs/JL18FBSSINS.pdf
JL18FBSSINS - REV 6 6/8/2020 Page 2
Remove (2 vertical clips, 4 horizontal) that secure the trim strip in place.3
The instructions shown below include removal of the original plastic from bumper. Your bumper may be different.1
Start by locating the 2 vertical clips and 4 horizontal clips on the top of the bumper.2
JL18FBSSINS - REV 6 6/8/2020 Page 3
There will be 2 screws holding the trim strip to the vehicle body, one on each side. These can be accessed by reaching through the wheel well.
You can now remove the trim strip to access the bumper mount bolts.
Also remove the factory skid plate. Start with the two 6mm screws on the bottom (one on either side).
4
5
6
JL18FBSSINS - REV 6 6/8/2020 Page 4
The skidplate is held to the vehicle with eight (8) clips in the front, and the two bolts you just removed, on the bottom.
Also remove the crash bar, there are two bolts holding it on.After the bolts are removed, you will shift the crash bar slightly up, then pull towards you to remove the tabs out of the opening.
Undo the wire harness plug that connects the foglights to the vehicle.
7
8
9
JL18FBSSINS - REV 6 6/8/2020 Page 5
The bumper is secured to the vehicle with four (4) bolts on both sides. Remove these and the bumper should come off the vehicle.
Once the plastic trim piece is off, remove the three T-20 screws (circled) that hold the foglight housing in place.
10
11
12
The bolts that hold the bumper together are held in place using locking tooth washers, you can either pry them up with a screwdriver, or cut them off using a sharp chisel or similar tool.
JL18FBSSINS - REV 6 6/8/2020 Page 6
JL18FBSSINS - REV 6 6/8/2020 Page 7
If your Halogen or LED fog lights are from the OEM Plastic bumper, you will need to drill a couple holes in the fog light flange to be able to mount into you LOD bumper.
Assemble your fog light to the Fog Light Bracket using the single Button Head Screw and Washer and Nut.
Center your fog light in the new Fog Light Bracket as shown and then mark the two mounting holes circled on the fog light flange. Drill these using a Ø1/4” drill bit.
Be careful when you drill these since the existing mounting holes in the plastic flange are not quite in the correct location.
Drill these two holes
5
64
HARDWARE KIT
3
NOTES:
JFB1820 = BARE STEEL OPTION1.JFB1821 = BLACK POWDER COAT OPTION2.
1
9
10
910
2
107
JEEP HALOGEN/LEDFOG LIGHT
JEEP LED FOG LIGHT8
ITEM NO. PART NUMBER DESCRIPTION
NO BULL BAR QTY
1 4JFB0720-01 DESTROYER SERIES FULL WIDTH BUMPER WELDMENT 1
ITEM NO. PART NUMBER DESCRIPTION
NO BULL BAR QTY
2 2JLB1800-03 JEEP JL/JT 2020+ FOG LIGHT BRACKET 23 LOD logo Logo Plate 1
4 HB431424ZPGR5 HEX BOLT 7/16-14 X 1.50 HEX BOLT ZINC PLATE GR5 8
5 HFN4314ZP HEX FLANGE NUT 7/16-14 ZINC PLATE 8
6 FW4318ZP FLAT WASHER Ø7/16 X 1.25" ZINC PLATED 8
7 HN2520ZPGR5 HEX NUT 1/4-20 ZINC PLATED GR5 10
8 HH081808SDZP HEX HEAD #8 X .50 SELF DRILLING SCREW ZINC PLATE 8
9 BHSCS252012ZP BHSCS 1/4-20 X .75 ZINC PLATE 1010 FW1209ZP FLAT WASHER #12 X .56" ZINC PLATED 20
N/A
DESTROYER FULL WIDTH FRONT BUMPER
JFB1820JFB1821
SHEET 1 OF 2
6/5/2020MCH
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REVDWG. NO.
DESCRIPTION:
NAME DATE
MFG APPR.
ENG APPR.
CHECKED
DRAWN
SEE NOTEFINISH:
MATERIAL:
DIMENSIONS ARE IN INCHESTOLERANCES: 0.010ANGULAR: MACH 1 TWO PLACE DECIMAL 0.015THREE PLACE DECIMAL 0.005
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF LOD LLC. ANY REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN PERMISSION OF LOD LLC IS
PROHIBITED.
LOD LLC.
CSHEET SIZE: B
1049ECO:
Once the holes are drilled, you can assemble the fog light and bracket onto the mounting bezel inside your LOD front bumper. Use the provided button head Screws, nuts and washers as shown.
14
13
15
JL18FBSSINS - REV 6 6/8/2020 Page 8
Mount the Winch Plate as shown below. Depending on the brand or style of winch, you may need to move the spacers to the outer position. This will shift your winch closer to the Jeep grill.
16
JL18FBSSINS - REV 6 6/8/2020 Page 9
Secure the winch plate in place using the supplied washer and bolt to attach the frame rail flaps to the frame.
Slide one of the steel spacers in between the winch plate and frame rail mount on your JL, then insert the long bolts and washers provided through the mounting holes and spacers as shown in this picture.
Using a 3/4” socket, tighten up the winch plate frame rail flaps as shown in this picture.
Depending on the brand or style of winch, you may need to move the spacers to the outer position. This
will shift your winch closer to the Jeep grill.
18
19
17
JL18FBSSINS - REV 6 6/8/2020 Page 10
Loosely secure the bumper in place using the nuts provided.
Before installing all of the mounting hardware, check to make sure your winch will fit by lining it up with the mounting holes on your winch plate.
Gently slide the bumper over the frame mounts and slowly move it forward, letting it rest on top of the frame.
Repeat until all the steel spacers (4) are installed in between the winch plate and the frame rail
The bolts are should be sticking through the winch plate as shown in the picture.
20
21
22
JL18FBSSINS - REV 6 6/8/2020 Page 11
Install and tighten the remaining mounting bolts and nuts located on the outside of your Jeep JL frame rails using a 3/4” socket and wrench.
Using a 3/4” socket and wrench, install and tighten the remaining mounting bolts and nuts on the inside of your Jeep JL frame rails as shown in this picture.
23
24
JL18FBSSINS - REV 6 6/8/2020 Page 12
108
2
7
84
3
89
1
6
CEN
TERE
D S
LOT
13
14
13
14
14
11
5
JEEP
HA
LOG
EN/L
ED F
OG
LIG
HTJE
EP L
ED F
OG
LIG
HT
12
NO
TES: JF
B185
0 =
BARE
STE
EL O
PTIO
N1.
JFB1
851
= BL
AC
K PO
WD
ER C
OA
T O
PTIO
N2.
HARD
WA
RE K
IT
ITEM
N
O.
PART
NUM
BER
DES
CRI
PTIO
NST
AN
DA
RD
NO
BUL
L BA
R/Q
TY.
14J
FB07
50-0
1SI
GN
ATU
RE F
ULL
WID
TH F
RON
T BU
MPE
R W
ELD
MEN
T - S
TAN
DA
RD1
24J
WP0
700
WIN
CH
PLA
TE1
ITEM
N
O.
PART
NUM
BER
DES
CRI
PTIO
NST
AN
DA
RD
NO
BUL
L BA
R/Q
TY.
34J
WP0
700-
02W
INC
H PL
ATE
SPA
CER
WEL
DM
ENT
44
2JW
P180
0-01
SPA
CER
WA
SHER
2
52J
LB18
00-0
3JE
EP J
L/JT
202
0+ F
OG
LIG
HT
BRA
CKE
T2
6LO
D L
ogo
Logo
1
7HB
4314
32ZP
GR5
HEX
BOLT
7/1
6-14
X 2
.00
HEX
BOLT
ZI
NC
PLA
TE G
R58
8FW
4318
ZPFL
AT
WA
SHER
Ø7/
16 X
1.2
5" Z
INC
PL
ATE
D18
9HN
4314
ZPG
R5HE
X N
UT 7
/16-
14 Z
INC
PLA
TE G
R58
10HB
1015
0M35
ZPC
L88
HEX
BOLT
M10
-1.5
0 x
35m
m Z
INC
PL
ATE
CL8
.82
11HN
2520
ZPG
R5HE
X N
UT 1
/4-2
0 ZI
NC
PLA
TED
GR5
10
12HH
0818
08SD
ZPHE
X HE
AD
#8
X .5
0 SE
LF D
RILL
ING
SC
REW
ZIN
C P
LATE
8
13BH
SCS2
5201
2ZP
BHSC
S 1/
4-20
X .7
5 ZI
NC
PLA
TE10
14FW
1209
ZPFL
AT
WA
SHER
#12
X .5
6" Z
INC
PL
ATE
D20
N/A
SIG
NA
TURE
FUL
L W
IDTH
FRO
NT
BUM
PER
- STA
ND
ARD
JFB1
850
JFB1
851
SHEE
T 1
OF
4
6/5/
2020
MC
H
UNLE
SS O
THER
WIS
E SP
ECIF
IED
:
SCA
LE: 1
:8
REV
DW
G.
NO
.
DES
CRI
PTIO
N:
NA
ME
DA
TE
MFG
APP
R.
ENG
APP
R.
CHE
CKE
D
DRA
WN
SEE
NO
TEFIN
ISH:
MA
TERI
AL:
DIM
ENSI
ON
S A
RE IN
INC
HES
TOLE
RAN
CES
: 0.
010
AN
GUL
AR:
MA
CH
1
TW
O P
LAC
E D
ECIM
AL
0.
015
THRE
E PL
AC
E D
ECIM
AL
0.
005
PRO
PRIE
TARY
AN
D C
ON
FIDE
NTIA
L
THE
INFO
RMA
TION
CO
NTA
INED
IN
THIS
DRA
WIN
G IS
THE
SO
LE
PRO
PERT
Y O
F LO
D L
LC.
AN
Y RE
PRO
DUC
TION
IN P
ART
OR
AS
A
WHO
LE W
ITHO
UT T
HE W
RITT
EN
PERM
ISSI
ON
OF
LOD
LLC
IS
PRO
HIBI
TED
.
LOD
LLC
.
DSH
EET
SIZE
: B10
49EC
O:
JL18FBSSINS - REV 6 6/8/2020 Page 13
JL JeepSignature SeriesFRONT BUMPERSHIPPING SHEET
Packaged by:________________________
On:________________________
BOLT KIT (may vary)
InstructionBooklet
BUMPER - Style may vary
WINCH PLATE
JL18FBSSINS - REV 6 6/8/2020 Page 14
JL JeepSignature Series
Front BumperBolt Kit
Packaged by:________________________
On:________________________
#8 SELF TAPPING SCREW
(x8)
FLAT WASHER7/16 X 1.25
(x18)
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
Standard Flat Washer Sizes
#10
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
HEX BOLT M10-1.50 X 35MM
(x2)
JL18FBSSINS - REV 6 6/8/2020 Page 15
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
Hex B
olts
1/4” - 20 x 2.5”
1/4” - 20 x .75”
#10 - 24
#8 - 32
#6 - 32
5/16” - 18 x 2.5”
5/16” - 18 x 1”
3/8” - 16 x 2.5”
3/8” - 16 x 2”
3/8” - 16 x 1”
7/16” - 14 x 2”
7/16” - 14 x 3.5”
7/16” - 14 x 2.5”
7/16” - 14 x 1.5”7/16” - 14 x 1”
1/2” - 13 x 2.5”
1/2” - 13 x 4”
1/2” - 13 x 4.5”
9/16” - 12 x 2.5”
9/16” - 12 x 6”
Length is measured from
under the head to the end of the bolt
#4 - 40
#10 - 24 x 35mm
HEX BOLT 7/16-14 x 2.00(x8)
HEX NUT 7/16-14
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex N
ut Sizes
1/2"
5/8"9/16"
3/4"
7/8”
1”
#10
#8 #6 #5 #4 #3
1/4"
5/16"
7/16"
3/8"
#12
#2 #1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
(x8)
BUTTON HEAD1/4-20 x 0.75
(x10)
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”B
utton Bolt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
Button B
olt Sizes
#2-56 x 1”
#4-40 x 1”
#6-32 x 1”
#8-32 x 1”
#10-24 x 1”
#10-32 x 1”
#12-24 x 1”
1/4"-20 x 1”
1/4"-28 x 1”
1/4"-28 x .5”
5/16"-18 x 1”
5/16"-24 x 1”
3/8"-24 x 1”
3/8"-16 x 1”
1/2"-13 x 1”
1/2"-20 x 1”
4mm
x 0.7
5mm
x 0.8
6mm
x 1.0
8mm
x 1.25
8mm
x 1.0
10mm
x 1.5
10mm
x 1.25
10mm
x 1.0
12mm
x 1.75
12mm
x 1.5
12mm
x 1.25
1/2"-13 x 2”
1/4"-20 x 3/4”
FLAT WASHER#12 X .56
(x20)
HEX NUT1/4-20(x10)
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
Hex Nut Sizes
1/2"
5/8" 9/16"
3/4"
7/8”
1”
#10
#8
#6
#5
#4
#3
1/4"
5/16"
7/16"
3/8"
#12
#2
#1
#0
14mm
2mm
2.5mm
3mm
4mm
5mm
6mm
8mm
10mm
12mm
16mm
18mm
20mm
7mm
JL18FBSSINS - REV 6 6/8/2020 Page 16
SPACER WASHER2JWP1800-01
LOD LOGOPACKAGED SEPERATE IF BUMPER IS BARE STEEL
(x1)
(x2)FOG LIGHT BRACKETS2JLB1800-03
(x2)
JL18FBSSINS - REV 6 6/8/2020 Page 17
1/2” SPACER PLATES4JWP0700-02
(x4)