Site Materials 10(1)

Telecom 2008For Ericsson

Telecom

Ericsson support:

[email protected]

How to order:All products in this catalogue are to be found in Ericsson Configuration Portfolio (ECP).The most commonly used products are also configurable in Variant Configuration (VC) through ECP or Market Unit System (MUS).

References:

Site Installation Material Overview, 151 86-EN/LZT 751 0049 UenSite Implementation Team Products Overview, 151 86-EN/LZT 751 0014 UenSite Installation Material Guidelines, 151 86-EN/LZT 751 0069 UenStandard Module Overview Feeder System Products, 131 22-COH 109 393/3 UenDistribution Frame (DF-OVP) for GSM, 2135-NBA 101 22+ Uen

1

TelecomInstallation material ........................................................... 2

Site Installation kit, Outdoor ............................................ 4

Cable ladders Outdoor .................................................... 5

Site Installation kit, Indoor ............................................... 6Cable ladders Indoor ....................................................... 7

Cable profile bar Indoor .................................................. 8

19" Rack material ............................................................ 9Cable duct ..................................................................... 10

Cable sealing ................................................................ 12

Cable sealing, Other ..................................................... 15Grounding material ....................................................... 17

Grounding material, Other ............................................ 21

Adjustable platform material ......................................... 22Antenna support material .............................................. 23

Common fastening material .......................................... 26

Miscellaneous installation material ............................... 27

Optical Interface Link, RRU ............................................. 30Main-Remote Systems .................................................. 30

Tools ................................................................................. 32

Torque wrench tools ..................................................... 35Crimping tools ............................................................... 37

Connector and cable tools ............................................ 38

Power tools ................................................................... 39Special Tools ................................................................ 40

Compasses ................................................................... 41

RBS Installation and test ............................................... 41Safety Equipment .......................................................... 42

Lifting Equipment .......................................................... 43

Miscellaneous Equipment ............................................. 441/2" LDF4 Feeder system products .............................. 45

Site feeder system ........................................................... 46

7/8" AVA5 Feeder system proucts ................................ 461 1/4" LDF6 Feeder system products ........................... 47

1 5/8" AVA7 Feeder system products ........................... 48

1/2" Jumper Cable FSJ4 (Angle) .................................. 491/2" Jumper Cable FSJ4 (Straight) ............................... 49

1/4" Jumper Cable FSJ1 ............................................... 50

Jumper Cable ................................................................ 50Fire Retardant Feeder Cable ........................................ 51

Positiv Stop Connectors ................................................ 52

Connectors for Feeder Cable ........................................ 53Adapters ........................................................................ 54

Feeder system accessories .......................................... 55

Feeder clamps .............................................................. 56Distribution frame ............................................................. 57

OVP-PCM-module kit for RBS2106 .............................. 57

Power Back-up ................................................................. 58Battery 2106I ................................................................. 58

Battery 2106V3 ............................................................. 59

Ericsson number register ................................................ 61

2

INSTALLATION MATERIALINSTALLATION MATERIAL

Standard Installation Material Overview

INSTALLATION MATERIAL

3

Installation material

4


Site Installation kit, OutdoorGreenfield site towerThis kit is designed for a Greenfield Tower site. It is a complete solution ofinstallation material for the outdoor site. The cable runs, grounding wire,grounding rods, grounding bar and installation instructions are delivered in atransport optimized export package.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 3501/1 2310 480 540 95.23

Consists of:

Description Qty Description QtyCable ladder kit, 2x2.25m (W=400mm), AluZink 1 Basic wire kit, 70m, 35mm2 1Cable ladder cover kit, 2x1.125m, AluZink 1 Rod kit, 3m 1Wire kit, 40m 35mm2 1 Installation instruction 1Outdoor ground bar 1 Standard site material description 1

Greenfield site mastThis kit is designed for a Green Field Mast Site. It is a complete solution ofinstallation material for the outdoor site. The cable runs, grounding wire, grounding rods, grounding bar and installation instruc-tions are delivered in a transport optimized export package.


Consists of:

Description Qty Description QtyCable ladder kit, 2x2.25m (W=400mm), Alu-Zink

1 Rod kit, 3m 1

Cabble ladder cover kit, 2x1.125m, AluZink 1 Ground kit for guyed mast 1Wire kit, 40m, 35mm2 1 Installation instruction 1Outdoor ground bar for mast 1 Standard site material description 1Basic wire kit, 70m, 35mm2 1

Roof top siteThis cable ladder set is used on a roof top site to carry cables between the antennasupport and the RBS cabinet/shelter. The set is supplied with jointing and fastening material as well as grounding screw.


Consists of:

Description Qty Description QtyCable ladder, 2.25m (W=300mm), AluZink 4 Joint 8End stop 4 L-T-X branch 1Universal ladder fixture 4 Screw/plug set (5pcs) 1Angle brackets 10 Grounding screw, M8x16 2Bolt kit, M8x16 (25pcs) 1 Tie strap set, 457x64mm, (50pcs) 1


5

Cable ladders OutdoorCable ladder kit, 2x2,5m, AluZink coatedThe outdoor Cable Run carries cables between the base station shelter and the tower, mast or antenna support. Used on green field sites each set carries 4,5 meter of cable ladders. The Cable Run set is designed as a modular and flexible cable carrying system and it is designed for free standing.


Consists of:

Description Qty Description QtyCable ladder 2.25m (W=400mm) 2 Installation bolt set 1Universal ladder fixture 2 Joint 4Angle bracket 6 Screw set with plugs 1End stop 2

Installation materialCable ladder cover kit, 2x1.125m, AluZink coatedThe cover set protects the cable run between the mast and the base station. It avoids falling ice, smal-ler stones as well as sunlight damaging the feeder cables.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 3159/1 1130 390 245 16.60Consists of:

Description QtyFall protection cover (W=400mm) 2Installation bolt set 1

6

INSTALLATION MATERIALInstallation Material Site Installation kit, Indoor

Basic ladder kit SmallThis kit is designed for a RBS room. Basic Indoor Kit is a complete solution of installation material for the indoor site and can be ordered in different sizes. Cable ladders and profiles, grounding system, marking and sealing material are delivered in a transport optimized export package.


Consists of:

Description Qty Description QtyCable ladder kit, Grey, 2x2.25m (W=300mm) 1 Cable kit 1m, 35mm2, Yellow/Green 2Cable profile, Grey, 2x0.6m 1 Common installation material 1Cable sealing kit for 1/4" - 7/8" cable 1 Site material description 1Cable kit 12m, 35mm2 , Yellow/Green 1 Indoor cable shute 1

Basic ladder kit MediumThis kit is designed for a RBS room. Basic Indoor Kit is a complete solution of installation material for the indoor site and can be ordered in different sizes. Cable ladders and profiles, grounding system, marking and sealing material are delivered in a transport optimized export package.


Consists of:

Description Qty Description QtyCable ladder kit, Grey, 2x2.25m (W=300mm) 2 Cable kit 1m, 35mm2, Yellow/Green 3Cable profile, Grey, 2x0.6m 2 Common installation material 1Cable sealing kit, for 1/4" - 7/8" cable 1 Site material description 1Cable kit 17m, 35mm2, Yellow/Green 1 Indoor cable shute 2

Basic ladder kit LargeThis kit is designed for a RBS room. Basic Indoor Kit is a complete solution of installation material for the indoor site and can be ordered in different sizes. Cable ladders and profiles, grounding system, marking and sealing material are delivered in a transport optimized export package.


Consists of:

Description Qty Description QtyCable ladder kit, Grey, 2x2.25m (W=300mm) 3 Cable kit 1m, 35mm2, Yellow/Green 4Cable profile, Grey, 2x0.6m 2 Common installation material 1Cable sealing kit for 1/4" - 7/8" cable 1 Site material description 1Cable kit 22m, 35mm2, Yellow/Green 1 Indoor cable shute 3



7

Cable ladders IndoorCable ladder kit, Sendzimir coatedThis indoor cable run is designed for mount in ceiling or on wall. The length 2.25 meter, renders pos-sible usage in buildings with narrow entrance, e.g. elevators. To obtain desired cable ladder length; use several NTM 201 3160/1.The width of cable ladder is 300 mm.


Consists of:

Description Qty Description QtyCable ladder, Length 2250mm Width 300mm 2 Supporting Iron 3Joint 4 T-bolt M10x35 3Universal ladder fixture 4 Pendant bracket 3Angle bracket 6 Installation bolt set M8x16 1Pendant rail 2250mm 1 Grounding screw Ø=9mm, 35mm2 2Ceiling fixing 2 Screw set with plugs 2Cantilever arm 3

Cable ladder kit, Paint coated 300mmThis indoor cable run is designed for mount in ceiling or on wall. The length, 2.25 meter, renders pos-sible usage in buildings with narrow entrance, e.g. elevators. To obtain desired cable ladder length; use several NTM 201 3160/2.


Consists of:

Description Qty Description QtyCable ladder, Length 2250mm Width 300mm 2 Supporting Iron 3Joint 4 T-bolt M10x35 3Universal ladder fixture 4 Pendant bracket 3Angle bracket 6 Installation bolt set M8x16 1Pendant rail 2250mm 1 Grounding screw Ø=9mm, 35mm2 2Ceiling fixing 2 Screw set with plugs 2Cantilever arm 3

Cable ladder kit, Paint coated 400mm


Consists of:

Description Qty Description QtyCable ladder, Length 2250mm Width 400mm 2 Supporting Iron 3Joint 4 Junction 1Universal ladder fixture 4 T-bolt M10x35 3Angle bracket 6 Pendant bracket 3Pendant rail 2250mm 2 Installation bolt set M8x16 1Ceiling fixing 3 Grounding screw Ø=9mm, 35mm2 2Cantilever arm 3 Screw set with plugs 2


8


Cable profile bar IndoorCable Chute kit 2x2m, Paint coated, GreyThe cable chute carries and covers cable inside a RBS-room or RBS-shelter.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 2023/1 2010 110 70 9.10Consists of:

Description QtyCable ladder profile, 2m 2Cable ladder profile cover, 0.6 mm 2End Piece 2Assemble Screw, B8 40

Cable profile kit, 2x0.6m, Sendzimir coatedThis product is mounted on the wall and used to lead cables down from the cable run to the RBS cabi-net.


Description QtyFitting profile, 600x150x14 mm 2Screw and plug set, 4,5x50 mm 2Grounding screw, M6x12mm, Ø = 9mm 4

Cable profile kit, 2x0.6m, Paint coated, GreyThis product is mounted on the wall and used to lead cables down from the cable run to the RBS cabi-net.


Description QtyFitting profile, 600x150x14 mm 2Screw and plug set, 4,5x50 mm 2Grounding screw, M6x12mm, Ø = 9mm 4

Cable profile kit, 2x2m, Sendzimir coatedThe Cable Profile kit is a complement to the traditional Cable Ladder kit and is suitable for cable runs in close installation environment. It can be mounted on to vertical walls as well as on to horizontal ceiling. Cables are fixed to the Cable Profile with traditional tie straps.


Description QtyFitting profile, 2000x200x14mm 2Screw and plug set, 4,5x50 2Grounding Screw, M6x12mm, Ø=9mm 4

Cable profile kit, 2x2m, Paint coated, GreyThe Cable Profile kit is a complement to the traditional Cable Ladder kit and is suitable for cable runs in close installation environment. It can be mounted on to vertical walls as well as on to horizontal ceiling. Cables are fixed to the Cable Profile with traditional tie straps.


Description QtyFitting profile, 2000x200x14mm 2Screw and plug set, 4,5x50 2Grounding Screw, M6x12mm, Ø=9mm 4



9

19" Rack materialBattery shelf set, Painted coated, GreyBattery shelf set for floor mounted 19" Rack according to SS IEC 297 for indoor installation. Two shel-ves hold totally 300kg.


Description Qty19" Battery shelf, Depth 350mm 2Uprights 16 Unit 2Cross bars 2Assembly screw/nut set, M6x12mm (20pcs) 1Wall screw/plug set (5pcs) 1

Shelf set, Painted coated, GreyShelf set for 19" Telecom Rack according to SS IEC 297 for indoor installation. Two shelves hold totally 30 Kg.


Description Qty19" Basic shelf, Depth 350mm 2Rack screw/nut set, M6x12mm (10pcs)

1

Rack frame 48U, Painted coated, Grey19" Rack Frame is according to SS IEC 297 for indoor installation. It houses RBSequipment such as power, batteries, transmission, DF-OVP, connection modules etc.The 19" Rack System is applicable on other areas as well, due to flexibility andexpandability.The 19" Rack Frame is floor mounted and secured to the wall. The wall distance mounted is 350 mm and height is 2160 mm (48U).


Consists of:

Description Qty Description QtyUprights 48 Unit 2 Assembly screw/nut set, M6x12mm (20pcs) 1Wall brackets 4 Wall screw/plug set (5pcs) 2Cross bars 3 Grounding screw 2Rack screw/nut set, M6x12mm (10pcs) 2

Rack frame 16U, Painted coated, GreyA 19" standard data rack according to SS IEC 297 intended for mounting on wall, delivered with 4 sup-port bars. Rack height is 714 mm (16U) and wall distance 270 mm.


Consists of:

Description Qty Description QtyUprights 16 Unit 2 Assembly screw/nut set, M6x12mm (20pcs) 1Wall brackets 4 Wall screw/plug set (5pcs) 2Cross bars 2 Grounding screw 1Rack screw/nut set, M6x12mm (10pcs)

1

Cross connection setThe Cross Connection unit is according to IEC 297 for indoor 19" rack. It holds totally 20 10-pair termi-nal blocks, 5pcs 10-pair terminal blocks inluded. A conductor connected to the terminal block does not need any soldering, screw or isolation stripping. The plastic of the terminal block is self-extinguishing.


Description Qty19" Mounting frame 1Terminal block (10-pair) 5Rack screw/nut set, M6x12mm (10pcs) 1

10

INSTALLATION MATERIALInstallation material Cable duct

Basic cable duct kitThe Cable Duct can carry up to four 7/8" feeders as well as two grounding wires from the RBS cabinet to the antenna pole. The duct does not need to be secured on flat roof top sites, due to the weight. The feeder within the duct can be protected against mechanical influences by the optional cable duct cover.


Consists of:

Description Qty Description QtyCable Duct, Straight 10 Grounding bar 1Cable Duct, Straight with grounding space 1 Grounding Bolt Set, (10pcs) 1Cable Duct, Straight with ground bar 1 Jointing Tube Set, (30pcs) 1Cable Duct, Cover 2 Clamp Set, (100 pcs) 1Cover Screw Set (20pcs) 1

Cable duct 1m, 4x7/8"The Cable Duct carries RF feeder and grounding wire between the RBS cabinet and the antenna pole. Up to four 7/8" feeders and two grounding wires can be located within the duct. The Cable duct does not need to be secured on a flat roof top site, due to the weight.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 413/1 1000 300 90 17.00

Consists of:

Description QtyCable Duct, Straight 1Jointing Tube Set, (4pcs) 1Clamp set (15pcs) 1

E69 957 80


11

Cover kit 10m, 4x7/8"The duct covers protects the cable against mechanical influence such as water, sunlight snow and sand.


Consists of:

Description QtyCable Duct, Cover 10Screw Set (100pcs) 1

Cable duct 1m grounding, 4x7/8"Cable Duct with room for grounding equipment and grounding wires, which can be connected to the grounding bar.


Consists of:

Description Qty Description QtyCable Duct, Straight with grounding bar 1 Grounding Bolt Set ( 10pcs) 1Cable Duct Cover 1 Jointing Tube Set (4pcs) 1Cover Screw Set (10pcs) 1 Clamps Set ( 10pcs) 1Grounding Bar 1

Cable duct 1m open, 4x7/8"A Cable Duct with room for feeder grounding and branching of cable. If the long side of the duct is sawed up, it can even be used as T-branch.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 421/1 1000 320 110 19.00Consists of:Description QtyCable Duct, Straight with grounding space 1Cable Duct Cover 1Cover Screw Set (10pcs) 1Jointing Tube Set (4pcs) 1Clamps Set (10pcs) 1

Bend duct 90°, 4x7/8"This duct changes the direction of the cable duct on a roof top site.The angle of the bend can either be 45° or 90°.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 422/1 300 300 220 20.00Consists of:Description QtyCable Duct Bend 45° 2Cable Duct Cover 45° 2Cover Screw Set, (10pcs) 1Jointing Tube Set, (4pcs) 1

Cable duct T-junction, 4x7/8"Use the T-Junction cable duct to split feeder cable in different directions on roof top sites.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 423/1 840 580 110 25.00Consists of:Description QtyT-Junction Cable Duct 1T-Junction Cover 1Cover Screw Set, (10pcs) 1Jointing Tube Set, (4Pcs) 1

Keyhole saw, 230V ACThis power saw uses a double blade system to cut through walls of rubber cable ducts. It is supplied with hard metal blades and the supply voltage is 230 V. Lock off switch and blade brake for added security.

Product Number Length mm Width mm Height mm Weight kgsLTT 601 152/1 380 360 110 4.50Consists of:Description QtyPower aligator saw 220 V 1Blade for normal usage 2Blade, thinn edge 2

12

INSTALLATION MATERIALInstallation material Cable sealing

ComPlus 6x1, 1/4" - 7/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one single frame with 1 opening. The frame has integrated knockout cover that are easily removed before routing cables. The 6 smaller modules fit cables from dimensions from 1/4" up to 1/2". The 12 larger modules fit cables from 3/8" up to 7/8". One single mul-tidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect achieved.Fits indoor and outdoor installations. According to IP 54/ Firestop.


Description QtySide section composite frame 2Module set 1/4" - 7/8" 1

ComPlus 6x2, 1/4" - 7/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one frame with 2 openings in width. The frame has integrated knock-out covers that are easily removed before routing cables. The 3 smaller module fits cables with dimensions from 1/4" up to 1/2". The larger module fits cables with dimensions from 3/8 " up to 7/8". One single multidiameter module can seal cables of several dif-ferent diameters, simply by peeling layers away from the module halves until a perfect achieved.Fits indoor and outdoor installations. According to IP 54/ Firestop.Possible to compliment with two extra module sets if needed.


Description QtySide section composite frame 2Mid section composite frame 1Module set 1/4" - 7/8" 1


13

ComPlus 6x3, 1/4" - 7/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one frame with 3 openings in width. The frame has integrated knock-out covers that are easily removed before routing cables. The 3 smaller modules fits feeder cables with dimensions from 1/4" up to 1/2". The 12 larger module fits with dimensions from 3/8 "up to 7/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect achieved. Fits indoor and outdoor installations. According to IP 54/Firestop. Possible to compliment with two extra module sets if needed.


Description QtySide section composite frame 2Mid section composite frame 2Module set 1/4 - 7/8" 1

Complus 6x1, 7/8" - 1 5/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one single frame with 1 opening. The frame has integrated knockout covers that are easily removed before routing cables. The 6 modules fits cables with dimensions from 7/8" up to 1-5/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect fit is achieved. Fits indoor and outdoor installations. According to IP 54/ Firestop.


Description QtySide section composite frame 2Module set 7/8" - 1 5/8" 1

ComPlus 6x2, 7/8" - 1 5/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one frame with 2 openings in width. The frame has integrated knock-out covers that are easily removed before routing cables. The 6 modules fit cable with dimensions from 7/8" to 1-5/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a per-fect fit is achieved. Fits indoor and outdoor installations. According to IP 54/ Firestop. Possible to com-pliment with two extra module sets if needed.


Description QtySide section composite frame 2Mid section composite frame 1Module set 7/8" - 1 5/8" 1

ComPlus 6x3, 7/8" - 1 5/8"The Roxtec ComPlus frame is a lightweight composite frame. The frame consists of sections put together as one frame with 3 openings in width. The frame has integrated knock-out covers that are easily removed before routing cables. The 6 modules fits cable with dimensions from 7/8" to 1 5/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a per-fect fit is achieved. Fits indoor and outdoor installations. According to IP 54/ Firestop. Possible to com-pliment with two extra module sets if needed.


Description QtySide section composite frame 2Mid section composite frame 2Module set 7/8" - 1 5/8" 1

14


ComLite composite frame, 1/4" - 7/8"The Roxtec ComLite solution is a lightweight cable entry seal comprised of a compact composite frame and sealing modules. The 6 smaller modules fit cables with dimensions from 1/4" up to 1/2" and the 12 larger modules fit cables from 3/8" up to 7/8". Fits indoor and outdoor installations.


Consists of:

Description QtyComLite Frame 1CML 20W40 3CML 40 10-32 12Stayplate 4Assembly Gel 1

Swan NeckCable entry seal for roof. The Roxtec Swan Neck routing accessory for rooftop sites is areal cost-saver. 2 pcs of entry seal module NTM 201 3211/ 1 is included in the Swan Neck.The Swan Neck eliminates the need for additional construction and roof covering, which isoften associated with cable routing through rooftops. It is placed directly on top of the holecutting, and the cables are routed up and through a Roxtec entry seal, which secures thetightness of the passage. By using this product it will reduce costs dramatically.According to IP 66/ 67 / Firestop


Consists of:

Description QtyS 6x2 Swan Neck 1Gasket 1Module set 1/4 - 7/8" 1



15

Cable sealing, OtherSide sectionThe Roxtec ComPlus Side section is a lightweight composite framepart. The side section has integra-ted knock-out cover that are easily removed before routing cables. Fits indoor and outdoor installa-tions. According to IP 54/ Firestop.Two side sections creates a cable seal entry with one opening. Two side sections and one mid-section (SXK107411/2) creates a cable seal entry with two openings.


Description QtyComPlus, side section 1Bracket 2

Mid sectionThe Roxtec ComPlus Mid section is a lightweight composite framepart. The framepart is to be put together with SXK 107 411/1 (ComPlus Side section) to create multiple openings in width. The frame has integrated knock-out covers that are easily removed before routing cables.Fits indoor and outdoor installations. According to IP 54/ Firestop.


Description QtyComPlus mid section 1Bracket 2

Module set 1/4" - 7/8" for 12 feeder cablesProduct is installed in the Complus entry seal. The 6 smaller modules fit cables from 1/4" up to 1/2" and the 12 larger modules fits cables from 3/8 " up to 7/8".One single multidiameter module can seal cables of several different diameters, simply by peeling lay-ers away from the module halves until a perfect achieved.Installed in a Complus frame IP class 54/ Fireseal is achieved.


Description QtyWedge 1Stayplate 5RM 40 10-32 12RM 20W40 3Assembly Gel 1

Module set 7/8" - 1 5/8" for 6 feeder cablesProduct is installed in the Complus entry seal.The 6 modules fits cable with dimensions from 7/8" to 1 5/8" . One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect fit is achieved.Installed in a Complus frame IP class 54/ Fireseal is achieved.


Description QtyWedge 1Stayplate 3RM 60 24-54 6Assembly Gel 1

Pre-compression toolThe Roxtec Pre-compression tool is used during installation of Roxtec cable lead-in products. It com-press the modules before installing the wedge in a complus frame.

Product Number Length mm Width mm Height mm Weight kgsLTD 260 154/1 340 80 40 0.07

16


Round frame 1/4" - 7/8" for 1 cableThe Roxtec RS seal is a round seal for single cable or pipe entries in metal sleeves or core drilled holes. The two halves, with multidiameter technology, are adjustable to fit different cable or pipe diame-ters. The split construction makes it easy to install around existing cables or pipes.The RS sealing can be used for a single grounding wire and optical fiber.

Product Number Cable/pipe diameter Length mm Width mm Height mm Weight kgsNTM 201 3656/1 1/4"-1/2" 44 37 37 0.06NTM 201 3656/2 3/8"-7/8" 86 50 50 0.30

Round frame 3/8"-7/8" for 4 cables The Roxtec R frame is a round frame for installation in pipe sleeves or round holes. The compression is integrated in the frame and 4 cables/pipes with dimensions 3/8"-7/8" can be sealed. Supplied with a net installed on the back side for protection during horizontal installation. The frame can be cut open for installation around existing cables or pipes.It can seal power cable, optical fiber, grounding wire as well as RF-cable.


Consists of:

Description QtyR-frame 1RM 30 4



17

Grounding material

Cable kit 25m, 35mm² Yellow/GreenThis kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type con-figuration of the grounding system with this kit. It is supplied with Main Earth Terminal (MET), bran-ching and connection equipment.

Product Number Length mm Width mm Height mm Weight kgs4/NTM 201 201/3 300 300 80 10.45

Consists of:

Description Qty Description QtyS1Z1-K 1x35 (2 AWG), UL 90 °C 25m Jointing sleeve, C89 8Cable lug, KRF 35-10 8 Insulating cover 8Contact washer, 8.4 ST FZB 10 Grounding bar, 10x50mm2 1Nut, M6M M8 ST FZG 10 Screw, TKS NR 12x64 ST FZG 2Washer, BRB 8.4x16x1.6 ST FZV

10 Plug 2

Screw, M6S M8x30 HST FZV 10 Cable lug, KRF 35-8 8

Cable kit 25m, 35mm², Black, IndoorThis kit is part of the Indoor grounding system for the RBS cabinet. Create a line,ring or tree type configuration of the grounding system with this kit. It is suppliedwith Main Earth Terminal (MET), branching and connection equipment.

Product Number Length mm Width mm Height mm Weight kgs4/NTM 201 201/2 330 330 100 10,45

Consists of:

Description Qty Description QtyCable 1x35mm² S1Z1-K, Black 25m Insulating Cover 8Cable Lug 35mm², ¨ =10 mm 8 Earth bar Cross section = 50mm² 2Serrated Washer 10 Screw TKS type nr 12 4Nut, M6M M8 ST 8 10 Plug 4Washer, BRB 8,4x16x1,6 ST 10 Cable Lug, KRF 35-8 8Screw, M6S M8x30 H St 8.8 10 Installation Instruction 1Jointing Sleeve, C89 8

18


Cable kit 1m, 35mm², Yellow/GreenConnect cabinets and racks to the indoor grounding system.

Product Number Length mm Width mm Height mm Weight kgs5/NTM 201 201/3 140 140 35 0.48Consists of:

Description QtyCable 1x35mm2 Yellow/Green UL 90° 1Jointing Sleeve, C89 1Cable lug 35mm2, ¨ =8 mm 1Insulating Cover 1

Cable kit 2m, 35mm² Yellow/GreenConnect cabinets and racks to the indoor grounding system.


Consists of:

Description QtyCable, 2m x 35mm2 Yellow/Green 1Cable lug, KRF 35-8 1Jointing Sleeve, C89 1

Cable kit 2m, 25mm², black, IndoorConnect cabinets and racks to the indoor grounding system.


Consists of:

Description QtyCable S1Z1-K UL 90°, 25 mm², Black 2mJointing Sleeve C89 1Cable lug 25mm², ¨ =8 mm 1Insulating Cover 1

Basic wire kit 70m, 35mm²Ground the green-field site, roof top site or any outdoor site with a ring conductor arrangement (70m) with this kit. The ring conductor can be bonded with the MET, the Mast leg, the Cu wire and grounding rods with supplied parts.


Consists of:

Description Qty Description QtyCu-wire, Annealed 7 stringy, 35 mm2 1 Screw, M6S M8x30H 8Jointing Sleeve, C89 8 Contact Washer, LB-AZ M8 16Cable Lug, KRF 35-10 8 Nut, M6M M8 ST 8

Ground kit for guyed mast 50m, 35mm²Use this kit in the outdoor grounding system at the green field site. It either lengthens the existing grounding ring with 50 m or grounds the tower or guy.


Consists of:

Description QtyCu-wire, Annealed 7 stringy, 35 mm2 1Jointing Sleeve, C89 6Branching Al/Cu 25-150/10-95 4


19

Basic Extension ground kit 50m, 35mm²At the green field site, a roof top site or any outdoor site this kit extends an existing grounding ring with 50m Cu wire.It is supplied with c-clamps for jointing and branch off.


Consists of:

Description QtyCu-wire, Annealed 7 stringy, 35 mm2 1Jointing Sleeve, C89 2

Wire kit 40m, 35mm²The flexible ring electrode can be used in the grounding network at Green Field site, Container site, roof top site or any outdoor. It serves as ground net in the earthing system and is supplied with jointing sleeves for branching and screws for connection to the MET.


Consists of:

Description Qty Description QtyCable Lug 35 mm2 , ¨ =10 mm 6 Serrated Washer for M8 6Flexible Conductor, Annealed 7 Stringy, 35mm2 1 Nut, M6M M8 ST 8 6Screw, M6SH M8x30H 6 Jointing Sleeve, C89 6

Wire kit 50m, 50mm²The flexible ring electrode is buried around the green-field site. It serves asground net in the earthing system and is supplied with jointing sleeves for branching.


Consists of:

Description QtyFlexible Conductor, Annealed 7-Stringy 50mm² 1Jointing Sleeve, C89 10

Grounding barThis product is developed to be used as an Ground bar for masts, towers and city sites.Fits round members or diagonals 42-76 millimetre in diameter, or on rail anchor.


Consists of:

Description Qty Description QtyPlate 1 Screw, MC6S 6x20H 2VU-Bolt, M10 M8 CC-90 1 Washer, AZ 8.4 20Nut, M10 M6M M10 4 Washer, AZ 6.4 2Washer, ¨ = 10.5x20mm 2 Washer, 8.4 10Nut, M6M M8 10 Washer, 6.4 2Screw, MC6S 8x20H 10

Rod kit 3mSystem for deep grounding at Green Field Site, container site or any outdoor site without any central grounding system. The rod kit can be used to either achieve a good lightening protection or to balance the electric potential in the outdoor grounding system. Supplied with connectors for 25-50mm2 groun-ding wire.


Consists of:

Description QtyEarth rod, 1500mm 2Tip 1Coupling 1Driving stud 1Cable clamp 1

20


Common grounding materialUse the spare part set when jointing/branching off/connecting wires in the grounding system of the Radio base station. It can be used outside as well as inside the RBS shelter.


Consists of:

Description Qty Description QtyInsulating Cover 10 Tooth Lock Washer M8 20Cable Lug, KRF 25-10 10 Tooth Lock Washer M10 20Cable Lug, KRF 35-10 10 Nut, M8 20Cable Lug, KRF 50-10 10 Nut, M10 20Cable Lug, KRF 70-10 10 Screw, M8x25mm 20Cable Lug, KRF 95-10 10 Screw, M10x25mm 20Jointing Sleeve 89 20 Instruction 1



21

Grounding material, OtherJointing sleeveThe C-formed jointing sleeves are designed for jointing of FK (with few wires), nonisolated copper lines (earth wires) and connection of branch lines. The jointingsleeves can also be used for jointing for RK (with many wires), insulated cables andconnection of branch cables. Patent pending.

Product Number Type Branching size mm2 Length mm

Width mm

Height mm

Weight kgs

SNT 102 26 C 89 25-50/25-50;25/25-16 30 18 16 0.04

Indoor grounding 3/8" - 1 5/8"This kit connects 3/8" - 1 5/8" feeder with the indoor grounding system.


Consists of:

Description QtyHose Clip 1Cable, 1x25mm2, 2m 1Insulating cover 1Jointing Sleeve C89 1Cable lug, 25mm2 1

Indoor quick grounding 25-35 mm²Indoor grounding clamp for insulated multithreaded grounding or power cable with dimeter 9,5 - 11,5 mm (25-35mm2). UL approved design.This clamp is quick and easy to use in a narrow space. It does not require any large press tool. It joints 2 cables with cross sections according to table below.

Cross section 1 Cross section 225 mm2 25 mm2

25 mm2 35 mm2

35 mm2 35 mm2

Product Number Length mm Width mm Height mm Weight kgs Clamps Qty/kit

NTM 201 3657/2 290 160 170 2.08 25NTM 201 3657/1 170 210 90 0.87 10

Consists of:NTM 201 3657/1 NTM 201 3657/2

Description Qty QtyClamps 10 25Tool 1 1

22

INSTALLATION MATERIALInstallation material Adjustable platform material

Free standing plattform on roofThe platform is designed for rooftops where a non-penetrative freestanding solution isrequired. A Platform for outdoor RBS-Cabinets. Adjustable for up to six degrees inclinedroof plane. The platform is easy to assemble.

Product Number Length mm Width mm Height mm Weight kgsSMA 901 05/1 2320 670 445 200.00

Consists of:

Description Qty Description QtyRubber carpet 2 Washer, BRB 20Rubber carpet 5 Bolt, M6S 4I-beam 1 Grating 1I-beam 1 Holder for grating 4U-beam 3 Profile 1U-beam 2 Screw, Washer/Spring 8Bolt, M6S 22 Screw, M6S 2Washer, BRB 22 Washer, BRB 8Nut, M6M 44 Groundbar 1Frame for cabinet 1 Key/Spanner, 30mm 1Whole threaded rod, WTR

2 Key/Spanner, 18/19mm

1

Nut, M6M 20

Option for platformAntenna Support that is easy to install on the free standing platform. ( SMA 901 05/1 )Tube and Support are tiltable so the antenna rigging can be done without climing.

Product Number Length mm Width mm Height mm Weight kgsSXK 107 424/1 2540 290 250 41.00SXK 107 424/2 2540 290 250 51.70

Consists of:SXK 107 424/1 SXK 107 424/2

Description Qty QtyTelescopic strut 2 2Telescopic strut 2 2U-bolt set, CC92 1 1Clamp, CC62-145 1 1Bolt, M6S 9 9Bolt, M6S 3 3Nut, M6M 36 36Washer, BRB 14 14Bolt, M6S 6 6Angle 3 3Plate/Washer 1 1Foot for strut 1 1Tube, 2500mm 1 2Tube, 400mm - 1Bolt, M6S - 4Nut, M6M - 8Washer, BRB - 4


23

Installation materialAntenna support materialTower mountedThis universal antenna support is to be used in pairs mounted on tubular or profile antenna towerlegs. The support can be adjusted to tilt the antenna inclination.


Wall mountedThis antenna support is to be used in pairs mounted on walls. The support can be adjusted to tilt the antenna inclination.


Consists of:

Description QtyAntenna support (tower) 1Expander screw M8x90mm 4

Antenna tube, 2.9m and 4mThis tube is for mounting antennas.

Product Number Tube length

External diameter

Length mm

Width mm

Height mm Weight kgs

SXA 120 215/29 2900 75 2900 75 75 6.15SXA 120 216/40 4000 90 4000 90 90 14.40

Antenna support for wall or roof, 6mThis antenna mounting set is developed for sector- and parabolic antennas.The set can be installed on roof or wall.The footing and guy support can be wall/roof mounted through hole or with expanding effect.


Consists of:

Description Qty Description QtyFoot mount 2 3-sector clamp 3Screw 4 Screw 3U-bolt set M12 4 Shackle-bolt with pin 3Washer 24 Hammer capsules 6Nut 48 Whole threaded rod 3Threaded rod 6 Washer 6Square washer 6 Lifting eye nut 3Hammer capsules 6 Washer 3Tube Ø 75 L=3000mmm

2 Nut 6

Tube joint 1 Guy wire 3Set screw 4 Tension set 2

Wall mount, PanaramicThe panoramic mount is suitable for small antennas and sector antennas.The plates is turn able sideways 30 degrees at each side to make it possible to directthe antenna. The mount is suitable on walls and bigger chimneys.


Consists of:

Description Qty Description QtyAngle plate 2 Wood screw 4Angle plate 2 Wall plug 4Nut 6 Washer 4Nut 6 Screw 6

24


Antenna support kit for wall, 100-490mmA light none penetrating rooftop mount to install small-, sector-, and parabolic antennas.The mounting set can be mounted on almost any kind of low-walls (parapet) with thickness 100 - 490 mm. The force, the mount creates, is equally distributed, therefore it can be mounted on rather weak walls.Option: SXK-107 2157/1 makes it possibly to join a 1200 millimetre top tube.


Consists of:

Description Qty Description QtySquare profile 3 Rubber fender 6U-profile 1 Screw 12U-bolt-set 3 Locking nut 12Nut 4 Washer 12Washer 2 Screw 2Whole threaded rod 1 Washer 12Nut 2 Tube 1Washer, Nord lock 2 Tube 1

Antenna support kit for wall, 500-1000mmA light none penetrating rooftop mount to install small-, sector-, and parabolic antennas.The mounting set can be mounted on almost any kind of low-walls (parapet) with thickness 500 - 1000 mm. The force, the mount creates, is equally distributed, therefore it can be mounted on rather weak walls.Option: SXK-107 2157/1 makes it possibly to join a 1200 millimetre top tube.


Consists of:

Description Qty Description QtySquare profile 3 Rubber fender 6U-profile 1 Screw 12U-bolt set 3 Locking nut 12Nut 4 Washer 12Washer 2 Screw 2Whole threaded rod 1 Washer 12Nut 2 Tube 1Washer, Nord lock 2 Tube 1

Antenna tube, 3.0mAluminium tubeOption to the Antenna support kit for wall, SXK 107 2146/1 and SXK 107 2146/2. Enables mount of 2 Sector antennas with the antenna support kit.

Product Number Tube length mm

External diameter mm

Length mm

Width mm

Height mm

Weight kgs

SXK 107 2157/1 3000 60 3000 60 60 6.00

Antenna support for roof mount system, 3mThis product is designed to meet the demands for a sturdy roof top mount. The main tube is fixed to the roof and supported with two telescopic supports 1.955;3.2 m.The mount is flexible and can be mounted on a slanting roof.


Consists of:

Description Qty Description QtyTelescopic strut 2 Washer BRB 4Telescopic strut 2 Foot for strut 2Screw M6S 2 Bolt M6S 1Nut M6M 10 Wall mount/

foot2

U-bolt set, 7pcs 1 Washer BRB 1U-Clamp 1 Nut M6M 2Angle 2 Bolt M6M 1Screw M6S 4 Tube 1


25

Tiltable mounting system for high boarderThe tube for high eaves is designed to meet the demands of sturdy mount, for directional antenna and smaller parabolic dish. The non-penetrating mount is easy and fast to install.


Consists of:

Description Qty Description QtyTop Tiltable-Tube 1 Stop Screw 1Base Tiltable-Tube 1 Locking Nut 2L-Tube 1 Screw 1Rubber fender 1 Counter Weight 3Nut 16 Washer 4Screw 8 Screw 1Screw 2 Omega profile 1Washer 5

Guyed roof top kit, 3.0mThe Guyed roof top kit is designed to meet the demands of a sturdy antenna mount for directional antennas and parabolas. Mount it on a roof top site where drilling is not allowed. The construction is balanced with concrete blocks (500x500x50 mm). The blocks are not supplied.Installed it take up 1200x1200 mm of the roof surface.


Consists of:

Description Qty Description QtyRubber carpet 1 Locking nut 16Cross 1 Angle 4Threaded rod 4 Guy 6;Kit6; 1Washer 48 Mount f. Strut 4Nut 50 Screw 12Bottom plate 4 Screw 4Screw 8 Clamp w. Ear 2Foot 1 Tube 1Screw 2

Greenfield tripod, 5.5mThe 5,5 meter high Greenfield Tripod is designed to carry directional antennas and parabolas.It can be located on hills tops, parking lots, fields, or even on roof top sites where drilling is not allowed. The construction is preferably balanced with concrete blocks 500x500x50 mm (not supplied).


Consists of:

Description Qty Description QtyLower foot plate 3 Lower support clamp 3Upper foot plate 3 Lower support clamp

w. ear3

Angle 12 3-sector clamp 3Whole threaded rod 12 Centre tube 1Joint piece 3 Leg 3

3-Sector antenna mountThis product is designed to meet the demands of a sturdy clean 3-sector installation.The installation is fast and simple


Consists of:

Description Qty Description QtyClamp 6 Bracket 6Screw 6 Flat washer 12Screw 6 Screw 6Flat washer 6 Locking nut 6Locking nut 6

26

INSTALLATION MATERIALInstallation material Common fastening material

Common installation materialThe Common Installation materiel is consumable supplies for indoor installations. For example, inside the radio base station room you can fasten the feeder cable to a cable ladder if you use the cable clamp. Tie straps for strapping grounding cable, transmission cable, alarm cable etc. to cable ladders or cable profile. Electro tape of different colours to mark feeder sectors. By that way avoiding mixing up Tx/Rx branch during installation. Label holders for permanent marking of feeder by that way avoiding mixing up co-sited operators equipment.

Product Number Length mm Width mm Height mm Weight kgs7/NTM 201 201 410 320 105 2.87

Consists of:

Description Qty Description QtyTie Strap, 366x4.7 Black, 100 pcs 1 Screw, 100 pcs, TST

8x1 ½ PH21

Wall Plug, Red, 100 pcs 1 Electro tape, White 1Tie Strap,141x3.6 Natural, 100 pcs 1 Electro tape, Red 1Tie Strap,290x3.6, 100 pcs 1 Electro tape, Blue 1Tie Strap,112x2.4, 100 pcs 2 Electro tape, Black 1Cable Clip,10-14mm, 100 pcs 1 Label Holder, 100 pcs 1Screw, 100 pcs, TST 8x3/4 PH2 1

Additional fastening materialA complete set of mounting/fastening material for the RBS site. Expander screws, screws and plugs for fastening equipment no matter the type of wall. Possible to mount against brick, wood, concrete or plaster partion wall. Cable ties for strapping groun-ding, power, feeder cable to cable profiles and cable ladders.Pliers/punch bend for potential equalisation of metal objects in the site.


Consists of:

Description QtyCable clip TC 7-10mm l=25mm, white, 100 pcs 1Cable clip TC 10-14mm l=30mm, white, 100 pcs 1Tie strap w=3.6mm l=141mm, natural, 100 pcs 2Tie strap w=4.7mm l=366mm, black, 100 pcs 2Fixing band TUB 12, 10m 1Hammer screw fixing 5x50, 100 pcs 1Spring toggle cavity fixing 13xM5S, 25pcs 1Self drill cavity fixing 25Screw plug fixing 6x35, 25 pcs 1Screw anchor cavity fixing TMX-6D, 50pcs 1Screw anchor cavity fixing TMX-6E, 50 pcs 1Pliers/Punch-bend 1Tie strap 10x0.5mm, L=10m 1Set of materials: screw M8x16, nut, clamp, 10 pcs 2Tie strap support, 100 pcs 1Set of materials: screw M5x12, elastic washer, nut, 50 pcs 1Set of materials: screw M5x25, elastic washer, nut, 50 pcs 1Potential grounding kit 1Shield anchor set, 110mm 2Shield anchor set, 90mm 2Compartment box 1

Shield anchor, loose bolt set, M12x110mmShield Anchor set for fastening RBS Installation Frame and Cabinet.


Consists of:

Description QtyShield anchor, loose bolt set, M12x110mm 4Washer 4


27



Consists of:

Description QtyShield anchor, loose bolt set, M12x90mm

4

Washer 4



Consists of:

Description QtyShield anchor, loose bolt set, M12x130mm 4Washer 4

Screw and washer kit, M10x60mmBolt and washer for mounting the Power Cabinet BBS 2000i to the Base Frame.


Consists of:

Description QtyBolt, MC6S 10x60mm D ST 8.8 FZV4 4Washer, BRB 22x11x2mm4 4

Screw and plug setUsed for connecting of equipment to walls. For use in indoor ladder system.

Product Num-ber

Length mm Width mm Height mm Weight kgs

NTM 201 257 120 90 30 0.15

Consists of:

Description QtyScrew, T6S 8X65 ST FZV 5Wall Plug, Green 5Washer, BRB 10.5X22X2 ST FZB 5

Cable tie, stainless steel band (Plascoat coated)Flexible tape-shaped tie strap with a disconnected locking device at one end. Use this tie strap to bundle together or fasten cables, lines or components.

Product Number Length mm Width mm Weight kgs Max Bundle diameterSET 145 064/230 230 6.4 0.007 55SET 145 064/305 305 6.4 0.009 80SET 145 095/457 457 9.5 0.020 130

Installation materialMiscellaneous installation materialTube kit, 2x3mThe flexible tube kit is used for protection of cables indoor against exterior mechanical influences.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 218/3 330 330 110 1.13Consistst of:

Description QtyFlexible Tube 25mm, l=3m 2Tube holder 15Jointing sleeve 5Conduit elbow 3

28


Tube kit, 3x3mThe flexible tube kit is used for protection of cables indoor against exterior mechanical influences.


Consists of:

Description QtyFlexible tube 25mm, l=3m 3Tube holder 15Jointing sleeve 3Conduit elbow 5Terminal box 3

Wall support kit for indoor cabinetMaterial for supporting RBS cabinet to wall.


Consists of:

Description Qty Description QtyAngel Bracket 2 Screw, T6S NR 8x65 ST FZV 2Pendant Rail 2 Washer, BRB 10.5x22x2 ST FZV 2Screw Set 1 Screw, M6S M10x25 H ST FZG 2Plug, TP4 2 Washer, BRB 10.5x20x2 ST FZG 2

Jointing sleeve kitThe Jointing Sleeve is used in the bonding point between two Cu wires in the grounding system. One jointing sleeve branch off /splice wire with the cross section according to the table below. The jointing sleeve is tested according to IEC 61238-1. Use the crimping tool set LTT 601 86 to accomplish a cor-rect crimp.


Consists of:

Description QtyJointing sleeve, C89 50

Wire 1 (mm²) Wire 2 (mm²)16 3516 5025 2525 5035 3535 5050 50

Cable lug kit, 35mm²This cable lugs are used for connecting of the power and grounding cables in an RBS site.Use the crimping tool set LTT 601 86 to accomplish a correct crimp.


Consists of:

Description QtyCable lug, 35mm2, hole 10mm 100

Cable lug kit, 50mm²This cable lugs are used for connecting of the power and grounding cables in anRBS site. Use the crimping tool set LTT 601 86 to accomplish a correct crimp.


Consists of:



29

Cable lug kit, 50 and 70mm²Used when connecting the RBS to the earthing system. Use the crimping tool set LTT 601 86 to accomplish a correct crimp.


Consists of:

Description QtyCable lug, Ø=50mm2 , hole 8mm 2Cable lug, Ø=70mm2 , hole 8mm 2



Consists of:




Consists of:


Cable lug kit, 150mm²Use these cable lugs to connect the power and grounding cable at the RBS site. Use the crimping tool set LTT 601 86 to accomplish a correct crimp.


Consists of:


ESB cableThis cable is used for synchronisation of RBS 2106 cabinets.

Product Number Length mm Weight kgsNTM 201 3072/1 3240 0.18NTM 201 3072/2 7020 0.37NTM 201 3072/3 12420 0.59NTM 201 3072/4 25380 1.06NTM 201 3072/5 75060 3.15Consists of:DescriptionCable 4x2Label holderCable clampConnectorCover shield

ESB Cable 3,240 m 1 1 1 1 ESB Cable 7,020 m 1 1 1 1 ESB Cable 12,420 m 1 1 1 1 ESB Cable 25,380 m 1 1 - - ESB Cable 75,060 m 1 1 - -

30

OPTICAL INTERFACE LINK, RRUOptical Interface Link, RRU Main-Remote Systems

Overlength Box kitThe box holds up to 30m OIL cable excess length. It is easy to mount to a wall, tower leg etc and pos-sible to stack on to each other.


Cable Support kitEnd support for three power cables and three OIL cables in the tower and mast, one hoisting grip for each cable. Three hosting grip for each oval quick link. The oval quick link fitted to the wire loop sup-port.


Outdoor Cable Tube kitThe cable tube kit is used outdoor for protection of cables and fiber against exterior mechanical influen-ces. The tube is possible to open for easy installation of preassembled cables and updates. Each tub is 1.7m long and inner diameter is 35mm, enough to fit three OIL cables and three power cables.Fastening material for tower/mast mounting and wall mounting included.


Indoor Cable chuteThe cable chute is used indoor for protection of cables and fiber against exterior mechanical influen-ces.Wall mounting or cable ladder mounting.


Labelset WCDMA, RRUMarking of optical fibre cables and power cables for WCDMA (RRU) systems.


Consists of:

Description Qty Description QtyLabel sheet (Sector 1) 1 Label sheet (OIL) 1Label sheet (Sector 2) 1 Label sheet (Power) 1Label sheet (Sector 3) 1 Label sheet (A) 1Label sheet (Sector 4) 1 Label sheet (B) 1Label sheet (Sector 5) 1Label sheet (Sector 6) 1

Labelset GSM, RRUMarking of optical fibre cables and power cables for GSM (RRU) systems.


Consists of:

Description QtyLabel sheet (Cell A) 1Label sheet (Cell B) 1Label sheet (Cell C) 1Label sheet (DX1) 1Label sheet (DX2) 1Label sheet (Power) 1Label sheet (OIL) 1

OPTICAL INTERFACE LINK, RRU

31

Fiber check toolThe Fiber check tool is an simple way of verifying that the OIL cable is ok, and that it´s not been dama-ged e.g. during installation. The pen is held in one end of the OIL cable and if the cable is ok a red light from the laser pen is visible in the other end. If no light is visible then is either the cable end dirty, and have to be cleaned, or the cable is damaged, and have to be replaced. The pen can be set to either have flashing or continuous light. It comes in a box with two AAA-batteries inclouded.

Product Number Length mm Width mm Height mm Weight kgsLBP 112 102/1 175 70 22 0.11

Ferrule end-face cleaner

The cleaning tool can be used in the field or in the factory to effectively clean ferrules within adapters and cable assemblies and restore the fiber optic connectors preformance. It has a polyester static free cloth for optimal cleaning. Includes 350 swipes per cleaner (1 swipe per cleaning).The cleaning tip is adjustable to 45 degrees for angled adapters and the tip is spring-loaded for control-led cleaning pressure. The cleaning tool is applicable for PC and APC type ferrules and ideal for clea-ning transciver ports.

Product Number Length mm Width mm Height mm Weight kgsLTT 601 154/1 280 60 27 0.11

32

TOOLSTools Tools

Personal tool setThe personal tool set is specially designed for site installation and relevant to all types of RBS cabinets.

Product Number Length mm Width mm Height mm Weight kgsLTT 601 135/1 230 500 400 13.40Consists of:

Description Qty Description QtyTool case 1 Saw blade, 12" 24tpi (10pcs) 1First Aid Kit 1 Socket set 3/8" 10-19mm, incl bits 1Static control wrist strap 1 Socket 16 mm 1Ear muffs 1 Socket 18 mm 1Eye protectors 1 Hexagon socket 8 mm for 3/8" wrench 1Gloves, size L 1 Hexagon socket 4 mm for 3/8" wrench 1Gloves, size XL 1 Screwdriver for Bits 1Cable cutter 1 Screwdriver TORX no. 10 1Side cutting plier 8160 1 Screwdriver TORX no. 15 1Slip joint plier 1 Screwdriver TORX no. 20 1Plate shears, straight 1 Screwdriver TORX no. 25 1Knife 1 Screwdriver TORX no. 30 1Wire stripper 0,2-6,0 mm 1 Screwdriver, 0.4x2,5x60 1Cable sheild cutter, 25-150 sq.mm 1 Screwdriver, PZ 2 1Pen hammer 1 Slotted socket 27 / 32mm 1Spirit level 200mm, magnetic 1 Extension bar 3/8" x 250 mm 1Termination tool, Krone 1 Set of U-wrench 1Tool for cable ties 1 U-wrench, 21-23 mm 1Measuring tape, 6 m 1 U-wrench 24-27mm 1File 6" ,flat 1 Multimeter kit 1File, half-round 1 Torx bit, TT30 1File, round 1 QMA Extractor 1Hack saw 1

Maintenance tool setThe maintenance tool set is specially designed to maintain the RBS equipment and relevant to all types of RBS cabinets.


Consists of:

Description Qty Description QtyTool case 1 Socket 18mm for 3/8" wrench 1First aid kit 1 Double flex wrench, 6 - 7mm 1Static control wrist strap 1 Hexagon socket 8mm for 3/8" wrench 1Penlight, mini with head band for lamp holding

1 Hexagon socket 4mm for 3/8" wrench 1

Side cutting plier 8160 1 Screwdriver for Bits 1Snip noce pliers 1 Screwdriver TORX no. 8 1Adjustable spanner l= 220mm 1 Screwdriver TORX no. 10 1Wire stripper 0,2-6,0mm 1 Screwdriver TORX no. 15 1RU-extractor handle, RU-extractor but-ton 35mm

1 Screwdriver TORX no. 20 1

Termination tool, Krone 1 Screwdriver TORX no. 25 1Tool for cable ties 1 Screwdriver TORX no. 30 1Slip joint plier 1 Screwdriver, 0.4x2,5x60 1Extractor tool for QMA-connectors 1 Slotted socket 27 / 32mm 1Multimeter 1 Nutdriver 5mm ( L=150mm) 1Powercable tool (WCDMA) 1 Pen hammer 1Socket set 3/8" 8-19mm, incl bits 1 Torx bit TT 30 1Socket 16mm for 3/8" wrench 1 Clutching tongs 1

TOOLS

33

Quality audit tool kitThe quality audit tool kit is especially designed to check the quality of the installation work at the site. Audits in an earthquake zone also requires Torque wrench LTT 601 141/1.

Product Number Length mm Width mm Height mm Weight kgsLTT 601 150 600 200 150 6.10

Consists of:

Description Qty Description QtyBack pack, XL 38L 1 Torque wrench, Range 5-25 Nm 1First-aid kit 1 Socket 10mm 1Compass, 3 different magn. Zones MN, ME and MS.

1 Bit cassette, with different bits and hol-ders

1

Binocular 8x21 1 Side cutting plier 1ESD Wrist-Strap 1 Electro tape L=20m, Black 1Measuring tape, L-3m 1 Self using tape 9m 1Electric-torch, Maglite mini 1 Adjustable spanner 1Spirit level, Length incl. Extension 700mm 1 Socket 13mm 1Screw driver 1

Special tool kitThis kit contains special tools for Ericsson RBS cabinets, designed to make it easier to install and maintain RBSs and avoid damaging parts.


Consists of:

Description Qty Description QtyExtractor tool EMILY Shield 1 Extractor tool for IDM Connector 1Slotted Socket 27/32mm 1 Extractor Tool for QMA Connector 1Wrist strap Kit 1 Power Cable Tool 1RU-Extract Handle button 1 Instruction 1Spanner for angle connector 7/8", 32mm 1

1/2" - 7/8" Feeder preparation tool kitUsed to prepare feeder cable (Andrew) with sizes 1/2" and 7/8". The tools are required to obtain a qua-lity installation of the connector and grounding. It includes tools to remove insulation, cut and polish the feeder end, spare blades and tape for temporary marking. The kit contains both hand tools and alterna-tive machine driven tools that requires a power tool e.g. Screwdriver machine LTT 129 09/2.


Consists of:

Description Qty Description QtyTool Box 1 U-wrench 32mm 1Feeder preparation tool ½", hand operated 1 Hack-saw 1Feeder preparation tool 7/8", hand opera-ted

1 Spare blade kit for hacksaw 10pcs 1

Feeder trimming tool ½" machine operated 1 File, flat 1Feeder trimming tool 7/8", machine opera-ted

1 Spare blade kit for feeder preparation tool 7/8", hand operated

2

Jacket removal tool for ½", feeder 1 Spare blade kit for feeder preparation tool ½" hand operated

1

Jacket removal tool for 7/8" feeder 1 Spare blade kit for feeder trimming tool ½" machine operated

1

Slip joint pliers 1 Spare blade kit for feeder trimming tool 7/8" machine operated

1

Cable knife 1 Marking tape, White 1Brass and fiber brush 1 Marking tape, Black 2U-wrench 19mm 1 Spare blade kit for jacket removal

tools ½" and 7/8"2

34

TOOLS

1 1/4" Feeder preparation tool kitUsed to prepare feeder cable (Andrew) with size 1 1/4". The tools are required to obtain a quality instal-lation of the connector and grounding. It includes tools to remove insulation, cut and polish the feeder end, spare blades and tape for temporary marking. The kit contains machine driven tools that requires a power tool e.g. Screwdriver machine LTT 129 09/2.


Consists of:

Description Qty Description QtyTool box 1 Cable knife 1Feeder trimming tool 1 1/4", machine operated 1 Brass and fiber brush 1Spare blade kit for feeder trimming tool 1 1/4" 1 Hack-saw 1Spare blade kit for jacket removal tool 1 1/4" 1 Spare blades kit for Hack-saw,

10pcs1

Jacket removal tool for 1 1/4" feeder 1 File, flat 1U-wrench 48mm 1 Marking tape, White 1Slip joint pliers 1 Marking tape, Black 2

1 5/8" Feeder preparation tool kitUsed to prepare feeder cable (Andrew) with size 1 5/8". The tools are required to obtain a quality instal-lation of the connector and grounding. It includes tools to remove insulation, cut and polish the feeder end, spare blades and tape for temporary marking. The kit contains machine driven tools that requires a power tool e.g. Screwdriver machine LTT 129 09/2.


Consists of:

Description Qty Description QtyTool box 1 Cable knife 1Feeder trimming tool 1 5/8", machine operated 1 Brass and fiber brush 1Spare blade kit for feeder trimming tool 1 5/8" 1 Hack-saw 1Jacket removal tool for 1 5/8" feeder 1 Spare blade kit for Hack-saw,

10pcs1

Spare blade kit for jacket removal tool 1 5/8" feeder

1 File, flat 1

U-wrench 57mm 1 Marking tape, White 1Slip joint pliers 1 Marking tape, Black 2

Tools

TOOLS

35

Torque wrench toolsTorque wrench, 2.7 Nm for N-ConnectionWrench 13/16" with fixed torque.2,7 Nm

Product Number Length mm Width mm Height mm Weight kgsLSS 103 25/1 240 190 40 0.53

Torque wrench, 5-25 NmThe tool set is suitable for installations at RBS sites. The torque driver fixes equipment with the torque range 5-25Nm.


Consists of:

Description QtyTorque wrench, 5-25 Nm 1Bits head ¼" bits 1Socket adaptor ¼" to 3/8" 1Socket head ¼" - 13mm 1

Torque wrench, 0.5-4.0 NmThe Torque Wrench kit is suitable to tighten connectors, bolts and screws with the torque range 0.4 - 4.0 Nm.


Consists of:

Description Qty Description QtyTorque-driver, 0.5 - 4 Nm 1 U-key, 8 mm for SMA-connector 1Bits Torx, T8 x 50 mm 1 U-key, 14 mm for TNC-connector 1Bits Torx, T25 x 50mm 1 U-key, 18 mm for N-connector 1Socket set, 7 Sockets and 1socket adapter Bits to ¼" , L= 50 mm 4.0, 4.5, 5.0, 5.5, 6.0,7.0 and 8.0 mm

1

Torque wrench, 0-10 Nm (WCDMA)A multi purpose tool suitable for tightening nuts or screws e.g. mounting the cabinet.The handle is equipped with a scale over the torque.0-10 Nm


Consists of:

Description QtyTorque-wrench, 1/4", 0-10 Nm 1Bits head,1/4"-bits 1Socket, 7 mm 1Bits Torx, T30 x 75 mm 1

Torque wrench, 20-100 Nm (Basic)The torque wrench fixes equipment with the torque range 20-100 Nm.Easy to handle during to the installation work of the RBS site.


Consists of:

Description Qty Description QtyTorque wrench, 20 - 100 Nm 1 Socket, 16mm 1Ratchet head, 3/8" 1 Socket, 19mm 1Socket adaptor, 3/8" to ½" 1 Extension bar 1Socket, 24mm 1

36

TOOLS

U-key set 27/32mmTo avoid any damage to the antenna interfaces the U-key is used for installing thefeederline connectors (7-16) together with a torque wrench. No torque wrench isincluded.Recommended tool: LTT 601 141/1 Torque Wrench, 20-100Nm.


Consists of:

Description QtyU-key, 27mm 1U-key, 32mm 1

Open jaw wrenchFor tightening with socket tools, e.g. Torque wrench LTT 601 141/1.

Product Number Description Weight kgsLSB 107 12/1 13mm 0.12LSB 107 12/2 19mm 0.16LSB 107 12/3 24mm 0.21LSB 107 12/4 27mm 0.23LSB 107 12/5 32mm 0.24LSB 107 12/6 16mm 0.16LSB 107 12/7 17mm 0.16

Tools

TOOLS

37

Crimping toolsGrounding and Lightening protectionHydraulic Press tool with 60 kN press power for Cu connections. Use it to crimp cable lugs and C-clamps in the grounding and lightning system of the radio base station (RBS). If the tool is used correc-tly withEricsson supplied C-clamps, Cable Lugs or Jointing Sleeves an electrical connectionaccording to SEN 24510 or BS 4579:1 is achieved.


Consists of:

Description Qty Description QtyCrimping Tool V 611, with tool case and Installation instruction

1 Press Die TB 9-13 Conductor area 16 mm² and 35 mm²

1

Press Die for C-lamp C4, C8, C9 and C89

1 Press Die TB7-20 Conductor area 10 mm² and 95 mm²

1

Press Die TB 8-17 conductor area 10 mm² and 70mm²

1 Press Die KB 25 Conductor Area 150 mm²

1

Press Die TB 11-14.5 Conductor area 25 mm² and 50 mm²

1

Coaxial connectors, 50 and 70 ohmThis flexible hand tool connects BNC and TNC connectors to coaxial cable.


Consists of:

Description Qty Description QtyCrimping tool 1 Press die, red, size 1/2A 1Allen key 1 Press die, yellow, size 2C 1Press die, orange, size 2B 1 Press die, no colour, size �� 1Press die, violet, size 3D 1

Opto cable connectorsUsed when applying connectors to an optical cable.


Consists of:

Description QtyStripping tool 1Pressing tool 1Polishing set 5

Tool set for PCM cable, 75 ohmsCrimping tol set for PCM cables, consists of LTT 601 108 and LTT 601 16.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 291 480 170 50 1.60

Consists of:

Description QtyCrimping, PCM Cable, 75 ¥ , inner conductor 1Crimping, PCM Cable, 75 ¥ , outer conductor 1

Plier set, DC cable, +24 VCrimping, DC Cable 24V for Transmission


Consists of:

Description QtyCrimping tool 1Press die 1

38

TOOLSTools

Connector and cable toolsTermination toolA tool commonly used within the public access net to create or remove cross connections inphone cabinets. The tool is fast to use if the trademark of the connection box is "Krone".

Product Number Length mm Width mm Height mm Weight kgsLSH 901 45/1 200 52 35 0.10

Extractor toolThe tool removes QMA-connections.

Product Number Length mm Width mm Height mm Weight kgsLSY 901 38/1 113 19 40 0.08

Clutching tongThis hand tool removes the power cable from the power magazine of the RBS. It is feasible for the models RBS 3202, RBS 3101, RBS 3402, RBS 3104, RBS 1130, RBS 1127 and RNC 3810.


Power-cable toolThe cable tool is suitable for releasing the cable from the connection /connector.


Tools

TOOLS

39

Power toolsHammer drill machine, 230V ACThe hammer drill machine drills through, plastics, wood, plaster or even through concrete during the construction work at the RBS site.


Consists of:

Description Qty Description QtyTool box 1 Hammer Drill 5,5mm L=120mm, (60mm*) 2Hammer drill machine 230V AC 1 Hammer Drill 6mm L=120mm, (60mm*) 2Chuck holder 1 Hammer Drill 8mm L=160mm(100mm*) 2Chuck 2 - 13mm 1 Hammer Drill 10mm L=160mm(100mm*) 2Key 1 Hammer Drill 12mm L=160mm(100mm*) 2

Hammer Drill 20mm L=200mm(150mm*) 2* Max. drilling depth

Hammer drill machine, cordless, 24V DCThe hammer drill machine drills through, plastics, wood, plaster or even through concrete during the construction work at the RBS site. This cordless hammer drill is delivered with one extra battery.


Consists of:

Description Qty Description QtyTool Box 1 Hammer drill 5.5mm L=120mm, (60mm*) 2Hammer drill machine 1 Hammer drill 6mm L=120mm, (60mm*) 2Extra Battery, 3.0Ah 1 Hammer drill 8 mm L=160mm, (100mm*) 2Charger, 230V, AC 1 Hammer drill 10 mm L=160mm, (100mm*) 2Chuck 2-13 mm 1 Hammer drill 12mm L=160mm, (100mm*) 2Chuck Holder 1 Hammer drill 20mm L= 200mm, (150mm*) 2Key 1 Maintenance set 1

* Max. drilling depth

Screwdriver machine, 12V DCFor common use when screwing and drilling. This cordless screwdriver is delivered with one extra bat-tery.

Product Number Length mm Width mm Height mm Weight kgsLTT 129 09/2 420 340 100 5.10Consists of:

Description QtyScrewdriver machine cordless 12V DC 1Extra Battery, 2.8 Ah 1Charger, 230V, AC 1Drill set, D=1.5mm - 6.5mm 1

Tools

40

TOOLS

Special ToolsSlotted socket, 27/32mmUsed when connecting jumpers in the RBS cabinet.

Product Number Length mm Width mm Height mm Weight kgsLSB 107 05/1 75 27 32 0.14

Extractor tool for AIUThis hand tool will be used for extraction of an Antenna Interface Unit (AIU) in the WCDMA RBS cabi-net.


Ru-extractor handleTool used for removing ESD-sensitive printed board assembly from the cabinet.


Wrist strap kit, ESD protectionWrist strap to connect user with ground during work with ESD sensitive equipment.


Pre-compression toolThe Roxtec pre-compression tool is used during installation of Roxtec cable lead-in productsto compress the modules before installing the wedge. Stainless Steel


Spanner for angle connectors 7/16, 32mmUse this hand tool to tighten 7/8". DIN 7/16 connectors in the Feeder system where the connector has a 90° angle and where the space is limited. Stainless Steel, SS2377.

Product Number Length mm Width mm Height mm Weight kgsLSB 107 30/1 75 55 45 0.07

Plate shareSelf opening non-slip, serrated jaws for rapid cutting.Compound lever action handles heavy stock, even when cutting tight curves.Convenient, protective safety latch.Cuts straight (or wide curves left or right in light stock) up to 1.2mm mild steel.

Product Number Length mm Width mm Height mm Weight kgsLDK 3016 250 60 30 0.43

Cable Tie TensionerTensioning BAND-IT Ties (steel) and Multi-Lok.

Product Number Length mm Width mm Height mm Weight kgsLSD 901 52/1 240 75 50 0.39

TOOLS

41

ToolsCompassesCompassCompass with Clinometer, type Northern Hemisphere (MN), type Equatorial (ME), type Southern Hemisphere (MS) .

Product Number Length mm Width mm Height mm Weight kgsZTY 203 26/5, MN 155 110 50 0.14ZTY 203 26/6, ME 155 110 50 0.14ZTY 203 26/7, MS 155 110 50 0.14

ToolsRBS Installation and testMultimeterIntended for general instrument for measurement of Voltage, Current and Resistance

Product Number Length mm Width mm Height mm Weight kgsLPK 102 024/3 185 90 43 0.42Consists of:

Description QtyInstrument 1Test Leads 1Instruction Sheet 1Soft Case 1

Antenna tester set, Bird Site analyzerThe Site Analyzer combines ease-of-use with powerful measurement and data analysis to help perform predictive maintenance. Suitable to use in worldwide cellular and PCS/DCS systems, supporting mea-surements of CDMA, GSM, TDMA and AMPS modulation schemes. Other applications include 3G, broadcast, government, tactical military, microwave, paging, public safety, trunking, WLAN and WLL, and TETRA.Frequency Range: 25 MHz to 6 GHzRejects "On-Frequency" interference up to +13dBmMaximum Input: +22 dBmPC software allows download to PC to analyze data for long-term assessment of system trends, pro-blems, and performance.Trace overlays to track performance over timeSaves 15 Calibrated SetupsStores 500 traces at 238 pts of resolutionAlphanumeric labeling of saved tracesColor display is viewable in direct sunlight

Product Number Length mm Width mm Height mm Weight kgsLPK 102 101/9 460 530 220 11.00

Consists of:

Description Qty Description QtyCalibration unit 7/16, open, short, load 1 Cord Europe 1Site Analyzer 25-6000MHz 1 Test cable (Nm-Nm) 1Calibration certificate 1 Case 1AC-charger 1 Precision Load 1CD- software 1 Adapter (Nf-Nf) 1Instruction Manual 1 Adapter 7/16female-7/16female 1Cable 9 pin 1 Adapter N female-7/16 male 1Automotive power adapter 1 Adapter N female-7/16 female 1

Antenna tester set, accessoriesAccessories to Bird Site analyzer when measuring on antenna systems for Micro RBSs.

Product Number Length mm Width mm Height mm Weight kgsLPK 102 107/1 250 330 120 0.80Consists of:

Description QtyTest Port Ext. Cable, N(m)-N(f), 3 m 1Standard N Type Load (f) 1Precision N(m) Open/Short/Load 1

Antenna adjustment tool

Product Number Length mm Width mm Height mm Weight kgsLPB 112 101/1 452 327 100 3.00

42

TOOLSTools Safety Equipment

Full Body Harness, Size S - XLThe full Body Harnesses is used to secure the worker during installation and maintenance on high alti-tude e.g. upon radio towers and roofs. The body harness is equipped with fixed D-ring to avoid neck damage by fall.

Product Number Description Weight kgsLYB 921 53/1 Size, S-M 1.60LYB 921 53/2 Size, L-XL 1.70

Tower work SetThis work set is intended for work in tower,mast and poles.

Product Number Length mm Width mm Height mm Weight kgsLYA 175 115/1 570 350 250 5.60

Consists of:

Description Qty Description QtySupport line, white 2 Protection gloves, inner size L 2 pairTool/bolt bag 1 Protection gloves, outer size L 2 pairHelmet 1 Protection gloves, outer size XL 2 pairProtection goggles 1 Protection gloves, inner size XL 2 pairBag, 27L 1Blood stopper 1Fall arrester device and energy absorber 1

Work line SetThis work line set is used for work in tower, mast, poles, roof and wall.


Consists of:

Description Qty Description QtySupport line, white 2 Protection gloves, inner size L 2 pairTool/bolt bag 1 Protection gloves, outer size L 2 pairHelmet 1 Protection gloves, outer size XL 2 pairProtection goggles 1 Protection gloves, inner size XL 2 pairBag, 27L 1Blood stopper 1Fall arrester device and energy absorber 1

Safety line SetThis Safety Line Set is used as fall protection when permanent fall protection equipment is missing in the towwer, mast and roof.


Consists of:

Description QtyBag, volume 40L, orange 1Core-mantle rope 100 mFall arrester device 1Carabiner, big 1Lifting sling 1.5m 1

Rescue line setThis kit is a rescue and evacuation set.


Consists of:

Description Qty Description QtyAntipodes rope, Red, 11.5mm 100m Shrinking Tube 2Express 25cm 1 Grillonrope,3m 1Lifting sling, 80cm 1 AMD Triact Autolock 1I5;D 10-11,5mm 1 Mini Traxion 1Ball lock 1 G.O. No.7 carabiner 1AMD Tract Autolock 2 Block,Mini 2Rope Bag,Red 1

Tools

TOOLS

43

Lifting EquipmentCarrying bag for indoor RBSCarrying bag for RBS 2206 and RBS 3202


Lifting handleFor Micro RBSs 2301, 2302


Carry to site


Tools

44

TOOLS

Miscellaneous EquipmentAntenna system installation equipmentThe Basic Tool Antenna system installation is a kit mandatory by antenna installations onhigh elevation. The kit contains tools as well as basic climbing equipment.


Consists of:

Description Qty Description QtyBox 800 1 Self-Breaking descend device 1Pad lock 1 Rope lock 1Shackle M16-1, 5 tons FZ 3 Block 2Sling 0.6m, for feeder lifting 3 Cabiner, big 1Working Gloves L 2 Rope lock, left 1Working Gloves XL 2 Rope lock, right 1Tool for band-it cable ties 1 Adjustable Webbing foot loop 1String Diam 2.8mm L=10m 1 Connecting sling 0.6m, green 2Ring Key 13mm 3 Connecting sling 0.8m, green 2Socket (long) 13mm 1 Connecting sling 1.5m, red 2Socket (long) 16mm 1 Carbiners, screw lock 10Socket (long) 17mm 1 Bag 360x280 2Adaptor ¼" - 3/8" 1 Lifting line 125m, Ø10mm 1

Feeder jack standThe feeder jack stand to be used when winding off feeder cables from a cable drum, capacity up to 5 tons.


Consists of:

Description QtyStand, 5 tons hydraulic jack for handling heavy cable drums

2

Tubular axle, L=2 m 1Stop collar 2

Service tent for RBS outdoorA tent designed for outdoor service of RBS in demanding environments. Fits in a backpack, easy to put together and made of hard-wearing material.


Step ladder, Combiflex 3.6mFor multi purpose use.


SITE FEEDER SYSTEM

45

1/2" LDF4 Feeder system products1/2" Feeder Cable on drumThe feeder cable is halogen free according to IEC 754-2 and UV-resistant. Minimum bending radius data refers to repeated bending (guaranteed number of bends, minimum: 15).Connector data: Connector insertion loss for mated connector pair, IL= 0.1*üf (GHz)

Cable data: LDF4-50ACondition 900MHz 1800MHz 2000MHz 2200MHzAttenuation (dB/100m)

6,9 10,1 10,7 11,2

Product Number Description Qty Weight kgsFAB 102 579/01 1/2", dielectric 500m 110.00

1/2" Connector for LDF4 Feeder CableCoaxial connector male, type 7/16 DIN male Positive Stop for 1/26; LDF4 feeder cable.The coax outer conductor is self-flare and the center conductor is captivated. The connector has O-ring sealing and is waterproof both matedand unmated. The interface dimensions are in accordance with 7/16-type in IEC 169-4.

Product Number Length mm Width mm Height mm Weight kgsRPT 899 023/1 150 150 50 0.20

1/2 " Feeder Grounding kitGrounding kit intended for grounding, shielding and sealing of coaxial feeder cables. Use toolkit LTT 601 143/1.

Product Number Length mm Width mm Height mm Weight kgsNGT 901 09/1 120 120 30 0.30

1/2" Feeder ClampsFeeder clampClamp for securing feeder cableIncludes cable socket, adapter, screw, threaded rod M8, nut and washer.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 215/1 125 65 30 0.17NTM 201 215/2 125 65 30 0.20NTM 201 215/3 125 65 30 0.23NTM 201 215/4 125 65 30 0.27

Site feeder system

46

SITE FEEDER SYSTEM

7/8" AVA5 Feeder system proucts7/8" Feeder cable on drumThe feeder cable is halogen free according to IEC 754-2 and UV-resistant. Minimum bending radius data refers to repeated bending (guaranteed number of bends, minimum: 15).Connector data: Connector insertion loss for mated connector pair, IL=0.1*üf (GHz)

Cable data: AVA5-50Condition: 900Mhz 1800Mhz 2000Mhz 2200MHzAttenuation (dB/100m): 3,6 5,2 5,55 5,85

Product Number Description Qty Weight kgsFAB 102 943/1 7/8" AVA5 500m 277.00

7/8" Connector for AVA5 Feeder CableCoaxial connector 7-16 DIN Female Positive Stop for 7/8" AVA5 feeder cable.The coax outer conductor is self-flare and the center conductor is captivated.The connector has O-ring sealings and is waterproof both mated and unmated.The interface dimensions are in accordance with 7/16-type in IEC 169-4.

Product Number Length mm Width mm Height mm Weight kgsRNT 899 94/1 66 37 37 0.29

7/8" Grounding kitGrounding kit intended for grounding, shielding and sealing of coaxial feeder cables. Use toolkit LTT 601 143/1.


7/8" Feeder ClampsFeeder clampClamp for securing feeder cableIncludes cable socket, adapter, screw, threaded rod M8, nut and washer.

Product Number Length mm Width mm Height mm Weight kgs6/NTM 201 230/1 130 90 45 0.196/NTM 201 230/2 130 90 45 0.246/NTM 201 230/3 150 100 50 0.296/NTM 201 230/4 170 110 50 0.36

Site feeder system

SITE FEEDER SYSTEM

47

1 1/4" LDF6 Feeder system products1 1/4" Feeder Cable on drumThe feeder cable is halogen free according to IEC 754-2 and UV-resistant. Minimum bending radius data refers to repeated bending (guaranteed number of bends, minimum: 15) .Connector data: Connector insertion loss for mated connector pair, IL=0.1*üf (GHz)

Cable data: LDF6-50Condition 900MHz 1800MHz 2000MHz 2200MHzAttenuation (dB/100m)

2,8 4,2 4,45 4,7

Product Number Description Qty Weight kgsFAB 102 138/01 1 1/4" dielectric 400m 376.00

1 1/4" Connector for LDF6 Feeder CableCoaxial connector female, type 7/16 DIN female Positive Stop for 1 ¼6; LDF6 feeder cable.The coax outer conductor is self-flare and the center conducto is captivated. The connector has O-ring sealing and is waterproof both mated and unmated. The interface dimensions are in accordance with 7/16-type in IEC 169-4.


1 1/4" Grounding kitGrounding kit intended for grounding, shielding and sealing of 1-1/4" coaxial feeder cable. Use toolkit LTT 601 143/2.


1 1/4" Feeder ClampsFeeder clampClamp for securing 1-1/4" feeder cableIncludes cable socket, adapter, screw, threaded rod M8, nut and washer.

Product Number Description Qty Weight kgs6/NTM 201 230/13 Feeder clamp 1-1/4"x1 1 0.226/NTM 201 230/14 Feeder clamp 1-1/4"X2 1 0.30

Site feeder system

48

SITE FEEDER SYSTEM

1 5/8" AVA7 Feeder system products1 5/8" Feeder Cable on drumThe feeder cable is halogen free according to IEC 754-2 and UV-resistant. Minimum bending radius data refers to repeated bending (guaranteed number of bends, minimum: 15) .Connector data: Connector insertion loss for mated connector pair, IL= 0.1*üf (GHz)

Cable data: AVA7-50Condition: 900MHz 1800MHz 2000MHz 2200MHzAttenuation (dB/100m): 2,15 3,2 3,4 3,6

Product Number Description Qty Weight kgsFAB 102 990/1 1 5/8" AVA7 300m 336.00

1 5/8" Connector for AVA7 Feeder CableCoaxial connector 7-16 DIN Female Positive Stop for 1 5/8" AVA7 feeder cable.The coax outer conductor is self-flare and the center conductor is captivated.The connector has O-ring sealing and is waterproof both mated and unmated.The interface dimensions are in accordance with 7-16-type in IEC 169-4.


1 5/8" Grounding kitGrounding kit intended for grounding, shielding and sealing of coaxial 1 5/8" feeder cables. Use toolkit LTT 601 143/3.


1 5/8" Feeder ClampsFeeder clampClamp for securing 1 5/8" feeder cableIncludes cable socket, adapter, screw, threaded rod M8, nut and washer.

Product Number Description Qty Weight kgs6/NTM 201 230/11 Feeder clamp 1 5/8"X1 1 0.226/NTM 201 230/12 Feeder clamp 1 5/8"X2 1 0.33

SITE FEEDER SYSTEM

49

Site feeder system1/2" Jumper Cable FSJ4 (Angle)1/2" Jumper Cable 1.0 - 3.5 m (Angle)FSJ4RN-50B-S1, UV-resistant, fire retardant according to CATVR, (wiring in vertical runs), IEC 60332-3-24C and recognised according to UL 1666, halogen free according to IEC 754-2.Diameter: 13,5mmMinimum bending radius, repeted bending: 32mmNumber of bends, minimum (typical): 20 (50).Attenuation, max value at 20í (dB) (including connector pair insertion loss, IL=0.1*üf (GHz)

MHzEricsson P/N Connectors Length(

m)450-468

824-894

872-960

1710-1880

1850-1990

1920-1980

2110-2170

TSR 951 70/1 7-16(m) - 7-16(m) 1 0,15 0,21 0,22 0,31 0,32 0,32 0,34TSR 951 70/2 7-16(m) - 7-16(m) 2 0,23 0,32 0,34 0,48 0,5 0,5 0,53TSR 951 70/3 7-16(m) - 7-16(m) 3 0,31 0,43 0,46 0,65 0,68 0,68 0,72TSR 951 322/1 7-16(m) - 7-16(m)

right angle1,5 0,19 0,27 0,28 0,4 0,41 0,41 0,44

TSR 951 322/2 7-16(m) - 7-16(m) right angle

2,5 0,27 0,38 0,4 0,57 0,59 0,59 0,63

TSR 951 322/3 7-16(m) - 7-16(m) right angle

3,5 0,35 0,49 0,52 0,74 0,77 0,77 0,82

Note:For RBS 2250 and RBS 3106/3206 the jumper cables at the RBS shall have an angled 7-16(m) con-nector in one end. This also means that the standard 1/2" feeder cables with stright 7/16(m) connectors (without jumper cables) cannot be used together with RBS 2250 and RBS 3106/3206.

Product Number Description Qty Weight kgsTSR 951 70/1 Coaxial jumper cable 1.0m 0.30TSR 951 70/2 Coaxial jumper cable 2.0m 0.50TSR 951 70/3 Coaxial jumper cable 3.0m 0.70TSR 951 322/1 Coaxial jumper cable 1.5m 0.50TSR 951 322/2 Coaxial jumper cable 2.5m 0.70TSR 951 322/3 Coaxial jumper cable 3.5m 1.00

Site feeder system1/2" Jumper Cable FSJ4 (Straight)1/2" Jumper Cable 5.0 - 10.0m (Straight)FSJ4RN-50B-S1, UV-resistant, fire retardant according to CATVR, (wiring in vertical runs), IEC 60332-3-24C and recognised according to UL 1666, halogen free according to IEC 754-2.Diameter: 13,5mmMinimum bending radius, repeted bending: 32mmNumber of bends, minimum (typical): 20 (50).Note:For RBS 2250 and RBS 3106/3206 the jumper cables at the RBS shall have an angled 7/16(m) con-nector in one end.This also means that standard 1/2" feeder cables with straight 7/16(m) connectors (without jumper cables) cannot be used together with TBS 2250 and RBS 3106/3206.

Product Number Length mm Width mm Height mm Weight kgsTSR 951 70/10 10000 35 35 2.30TSR 951 70/5 5000 13.5 13.5 1.20TSR 951 70/75 7500 13.5 13.5 1.75

50

SITE FEEDER SYSTEMSite feeder system 1/4" Jumper Cable FSJ1

1/4" Jumper Cable 1.5 - 3.5mCable data:FSJ1RN-50B-S1, UV-resistant, fire retardant according to CATVR, (wiring in verical runs), IEC 60332-3-24C and recognised according to UL 1666, halogen free according to IEC 754-2.Diameter: 7,4mmMinimumbending radius repeted bending: 25mmNumber of bends, minimum (typical): 15 (20).Note:The 1/4" jumper cables will give reduced RF performance compared to the corresponding 1/2" jumper cable. For RBS 3116 it is recommended to choose the 1/4" jumper when optional Transmission are planned to be installed in the Cabinet. The 1/2" jumpers will give limited access to the Transmisson equipment if not the jumpers are disconnected from Filter unit first.For the RBS 3216 it is tecommended to choose 1/4" jumper when a second Cabinet is stacked on top of the first Cabinet and more than six jumper cables are exiting from the topmost Cabinet.

Product Number Description Qty Length mmTSR 951 1193/1 Coaxial jumper cable 1 1500TSR 951 1193/2 Coaxial jumper cable 1 2500TSR 951 1193/3 Coaxial jumper cable 1 3500FSJ1RN-50B-S1, UV resistant, fire retardant according to CATVR, (wiring in verical runs), IEC 60332-3-24C and recognised according to UL 1666, halogen free according to IEC 754-2.Diameter: 7,4mmMinimum bending radius, repeted bending: 25mmNumber of bends, minimum (typical): 15 (20).Note:The 1/4" jumper cables will give reduced RF performance compared to the corresponding 1/2" jumper cable. For the RBS 3116 it is recommended to chose the 1/4" jumper when optional Transmission are planned to be installed in the Cabinet. The 1/2" jumpers will give limited acsess to the Transmission equipment if not the jumper are disconnected from Filter unit first.For the RBS 3216 it is recommended to choose 1/4" jumper when a second cabinet are stacked on top of the first Cabinet and more than six jumper cables are exiting from the topmost cabinet.

Site feeder system Jumper Cable1/4" Jumper CablesCable data:1/4" FSJ1 is UV-resistant, halogen free according to IEC 754-2 and have fire retardant jacketing accor-ding to:CATVR/UL 1666 (riser cable test) Therefore, cables meeting this requirement can also be used in the folowing lower level catagories:CATV/UL 1581 (vertical tray flame test), IEC 60332-3 (vertical bunched wires or cable), IEEE 383 (ver-tical tray flame test)CATVX/UL VW-1 (verical wire flame test), IEC 60332-1 (vertical single wire or cable).The jumpers are suitable for indoor and outdoor use.Diameter: 7,4mmMinimum bending radius: 25mm (repeated bending, guaranteed minimum number of bends: 15).

Product Number Length mm Width mm Height mm Weight kgsTSR 951 103/1 500 10 10 0.17TSR 951 103/2 1000 25 25 0.20TSR 951 103/3 2000 25 25 0.27TSR 951 101/01 500 25 25 0.22TSR 951 101/02 1000 25 25 0.25TSR 951 101/03 2000 25 25 0.27

SITE FEEDER SYSTEM

51

Fire Retardant Feeder Cable3/8" LDF2 Fire Retardant Feeder Cable on drumThe feeder cable is UV-resistant, halogen free according to IEC 754-2 and fire retardant according to CATVR/UL 1666 (rise cable test)CATV/UL 1581 (vertical tray flame test), IEC 60332-3 (vertical bunched cable), IEEE 383 (vertical tray flame test)CATVX/UL VW-1 (verical wire flame test), IEC 60332-1 (verical single cable).The feeder cable is suitable for indoor and outdoor use.Minimum bending radius data refers to repeated bending (guaranteed minimum number of bends: 15)

Product Number Description Qty Weight kgsFAB 102 1044/02 Fire retardant 500m 60.00FAB 102 1044/05 Fire retardant 300m 36.00

1/2" LDF4 Fire Retardant Feeder Cable on drum Halogen free and fire retardent 1/2" corrugated copper cable with solid inneconductor.Cable is used as feeder cable for antennas.This article forms a part of a product with special approval. Changen may not beintroduced without previous confirmation by design responsible. Following requirementsmust fullfilled.1. UL approved according to 16662. Flame retardent according to: UL 1581.1080 VW1 and IEC 332-1

Product Number Description Qty Weight kgsFAB 102 1044/01 1/2" Feeder cable UL/IEC 500m 110.00FAB 102 1044/04 1/2" Feeder cable 300m 72.00

7/8" AVA5 Fire Retardant Feeder Cable on drumThe feeder cable is UV-resistant, halogen free according to IEC 754-2 and fire retardant according to CATVR/UL 1666 (rise cable test)CATV/UL 1581 (vertical tray flame test), IEC 60332-3 (vertical bunched cable), IEEE 383 (vertical tray flame test)CATVX/UL VW-1 (verical wire flame test), IEC 60332-1 (verical single cable).The feeder cable is suitable for indoor and outdoor use.Minimum bending radius data refers to repeated bending (guaranteed minimum number of bends: 15)

Product Number Description Qty Weight kgsFAB 102 1943/1 Fire retardant 7/8" 500m 850.00FAB 102 1943/2 Fire retardant 7/8" 300m 700.00

1 1/4" LDF6 Fire Retardant Feeder Cable on drumThe feeder cable is UV-resistant, halogen free according to IEC 754-2 and fire retardant according to CATVR/UL 1666 (rise cable test)CATV/UL 1581 (vertical tray flame test), IEC 60332-3 (vertical bunched cable), IEEE 383 (vertical tray flame test)CATVX/UL VW-1 (verical wire flame test), IEC 60332-1 (verical single cable).The feeder cable is suitable for indoor and outdoor use.Minimum bending radius data refers to repeated bending (guaranteed minimum number of bends: 15)

Product Number Description Qty Weight kgsFAB 102 989/1 Fire Retardant 400m 380.00

1 5/8" AVA7 Fire Retardant Feeder Cable on drumThe feeder cable is UV-resistant, halogen free according to IEC 754-2 and fire retardant according to CATVR/UL 1666 (rise cable test)CATV/UL 1581 (vertical tray flame test), IEC 60332-3 (vertical bunched cable), IEEE 383 (vertical tray flame test)CATVX/UL VW-1 (verical wire flame test), IEC 60332-1 (verical single cable).The feeder cable is suitable for indoor and outdoor use.Minimum bending radius data refers to repeated bending (guaranteed minimum number of bends: 15)

Product Number Description Qty Weight kgsFAB 102 1944/1 Fire retardant 300m 525.00

52

SITE FEEDER SYSTEM

Positiv Stop Connectors7/16(f) positive stop connector for 1/2" LDF4

Product Number Lenght mm Width mm Height mm Weight kgsRNT 980 02/1 150 50 50 0.13

7/16(m) positive stop connector for 7/8" AVA5

Product Number Lenght mm Width mm Height mm Weight kgsRPT 980 05/1 150 50 50 0.28

7/16 (m) positive stop connector for 1 1/4" LDF6


7/16 (m) positive stop connector for 1 5/8" AVA7


Site feeder system

SITE FEEDER SYSTEM

53

Connectors for Feeder CableN (m) connector for 3/8" LDF2 Feeder CableCoaxial connector male, type N self flaring. The contact face dimensions are in accordance with N type in IEC 169-16. The O-ring make the connector waterproof when it is mounted to the cable. The inner contact has spring fingers and outer contact is self clamped.


N (m) positive stop connector, 1/2" LDF4N Male Positive StopP;, for 1/2" LDF4-50A cable.


N (f) positive stop connector, 1/2" LDF4


N (m) positive stop connector, 7/8" AVA5 and AL5


N (f) positive stop connector, 7/8" AVA5 and AL5


N (m) one piece connector, 1 1/4" LDF6


N (m) positive stop connector, 1 5/8" AVA7 and AL7


N (f) positive stop connector, 1 5/8" AVA7 and AL7


54

SITE FEEDER SYSTEM

AdaptersAdapter N (m) - 7/16 (m)Coaxial adapter N male to 7/16 male. The comtact face dimension are in accordance withN type in IEC 169-16 and 7/16 type in IEC 169-4. Environmental protection class IP68.The 7/16 type has an O-ring sealing and the N type has a gasket sealing.


Adapter N (f) - 7/16 (m)Coaxial adapter 7/16 male to N female type.The contact face dimensions are accordance with N type in IEC 169-16 and 7/16 type with IEC 169-4.The 7/16 type has a O-ring sealing.


Adapter N (m) - N (m)Coaxial adapter N male to N male. The contact face dimension are in acordance with N type in IEC 169-16.


Adapter N (f) - TNC (m)

Coaxial adapter N female to TNC male. The contact face dimensions are in acordance with N type in IEC 169-16 and TNC type in IEC 169-8.


Adapter N (m) - N (f), right angle


SITE FEEDER SYSTEM

55

Feeder system accessoriesShrink sleeve, 1/2", 13.5mm-39mmCoaxial connector sealing kit. Cold shrink termination for sealing of N-connectors or 7-16 DIN connec-tors to ½6; or 7/86; jumper cable.The termination outer layer tube provides weather-resistance and sealing over the cable and connec-tor. The termination inner layer tube provides reinforced mechanical protection during handling of the prepared cable over the connector area. The installation shall be done in one single operation without the utilization of additional tools and/or components for the weather-resistance and sealing over the cable and connector. The space, around the connection axis, needed for installation shall be within the value indicated on table below. The sealing outer surface shall be continuing without interruptions or overlapping.

Product Number Length mm Width mm Height mm Weight kgsMPB 134 01/1 150 43 56 0.08

Shrink sleeve, 1/2", 7/8" 13.5-39mmCoaxial connector sealing kit. Cold shrink splice for sealing of N-connectors or 7-16 DIN connectors for junction between ½. to ½. or ½. to 7/8. coaxial cables.The splice outer layer tube provides weather-resistance and sealing over the cable and connector. The splice inner layer tube provides reinforced mechanical protection during handling of the prepared cable over the connector area.The installation shall be done in one single operation without the utilization of additional tools and/or components for the weather-resistance and sealing over the cable and connector. The space, around the connection axis, needed for installation shall be within the value indicated on table below. The sea-ling outer surface shall be continuing without interruptions or overlapping.

Product Number Length mm Width mm Height mm Weight kgsMPB 134 02/1 300 43 56 0.18

Sealing setUse this sealing set to seal a splice in the RF system on a Telecom site. It protects the splice against vibrations, moisture and dust. Designed for feeder sizes 1/2", 7/8", 1-5/8", 1-1/4". This kit can be used to seal already installed equipment.

Product Number Length mm Width mm Height mm Weight kgsNTM 201 2426 310 220 150 0.30

Consists of:

Description QtyTape, self-fusing, l=9.15 m; w=19 mm 1Electrotape PVC, l=20.1 m; w=19 mm 1

Feeder system marking for GSMLabel blocks packed in a plastic bag marked NTM 201 207/1


Consists of:

Description Qty Description QtyLabel sheet (Cell A:) 2 Label sheet (TX3) 1Label sheet (Cell B:) 2 Label sheet (RXA) 1Label sheet (Cell C:) 2 Label sheet (RXB) 1Label sheet (Cell O:) 2 Label sheet (TX1) 1Label sheet (DX1) 1 Label sheet (TX2) 1Label sheet (DX2) 1

Feeder system marking for WCDMAMarking of antenna feeders for WCDMA system.


Consists of:

Description Qty Description QtyLabel sheet (Sector 1:) 1 Label sheet (Sector 5:) 1Label sheet (Sector 2:) 1 Label sheet (Sector 6:) 1Label sheet (Sector 3:) 1 Label sheet (A:) 1Label sheet (Sector 4:) 1 Label sheet (B:) 1

56

SITE FEEDER SYSTEM

Site feeder system Feeder clampsCable ClampsFeeder clampClamp for securing feeder cableIncludes cable socket, adapter, screw, threaded rod M8, nut and washer.

Product Number Cable clamp type Cable For cable6/NTM 201 230/51 7,2mmx1 ¨ 7,2mm 16/NTM 201 230/52 7,2mmx2 ¨ 7,2mm 26/NTM 201 230/53 7,2mmx3 ¨ 7,2mm 36/NTM 201 230/54 7,2mmx4 ¨ 7,2mm 46/NTM 201 230/41 10mmx1 ¨ 10mm 16/NTM 201 230/42 10mmx2 ¨ 10mm 26/NTM 201 230/43 10mmx3 ¨ 10mm 36/NTM 201 230/44 10mmx4 ¨ 10mm 46/NTM 201 230/61 14mmx1 ¨ 14mm 16/NTM 201 230/62 14mmx2 ¨ 14mm 26/NTM 201 230/63 14mmx3 ¨ 14mm 36/NTM 201 230/64 14mmx4 ¨ 14mm 4

Feeder Clamps bulk kitsClamp clips for mounting on M8-thread for feeder cable.Spare part clips.

Product Number Cable clamp type Clamps FeedersSXA 105 3055/4 1/2" 10SXA 105 3055/2 7/8" 10

DISTRIBUTION FRAME

57

Distribution frame

Distribution frame

OVP-PCM-module kit for RBS2106DF-OVP for WCDMA RBSThis is an empty DF-OVP panel to be equipped with a selection of OVP modules. It is designed for indoor mounting in a 19" frame or on a wall.

Product Number Length mm Width mm Height mm Weight kgsNBA 101 025/96 490 300 185 2.00

OVP modulesOVP modules that can be installed in NBA 101 025/96.

Expansion kit Customer interface DF/RBS cabling interface RBS system Weight kgs

NCD 300 12/10 120¥ Screw terminal 15m 120¥ 2pcs Dsub 15 RBS Indoor 2.30NCD 300 12/11 120¥ Screw terminal 7m 120¥ 2pcs Dsub 15 RBS Indoor 1.90NCD 300 12/21 100¥ Screw terminal 7m 100¥ 2pcs Dsub 15 RBS Indoor 1.70NCD 300 12/12 120¥ Screw terminal 15m 120¥ 2pcs RJ45 WCDMA Indoor 2.30NCD 300 12/13 120¥ Screw terminal 7m 120¥ 2pcs RJ45 WCDMA Indoor 1.90NCD 300 12/22 100¥ Screw terminal 15m 100¥ 2pcs RJ45 WCDMA Indoor 2.30NCD 300 12/23 100¥ Screw terminal 7m 100¥ 2pcs RJ45 WCDMA Indoor 1.70

DF-OVP for GSM RBSThe DF-OVP configrations are available for RBS 2206 V2.

NBA 101 22/1 16 external alarmsNBA 101 22/2 16 external alarms, 4 PCM systems 100/12 ohmNBA 101 22/3 16 external alarms, 4 PCM systems 75 ohmNBA 101 22/4 8 external alarms, 2 PCM systems 100/120 ohmNBA 101 22/5 8 external alarms, 2 PCM systems 75 ohm

Product Number Length mm Width mm Height mm Weight kgsNBA 101 22/1 490 290 250 5.60NBA 101 22/2 490 290 250 7.30NBA 101 22/3 490 290 250 7.30NBA 101 22/4 490 290 250 6.40NBA 101 22/5 490 290 250 6.40

OVP for Outdoor RBS transmission and alarms Overvoltage protection (OVP) for Outdoor RBS transmission and alarms The RBS is connected to the copper transmission network and to other external equipment on the site as alarms, GPS etc. To enable secure operation and prevent high maintenances costs is it vital that all copper connections to the RBS is protected against lightning and other high voltages that can occur in the telecom network. The lightning protections type NCD 901 26 has been designed together with the newest GSM and WCDMA RBS and to be compatible with older RBS. This insures that the protection will work together with all RBS-equipment and prevent damages and costly replacement of active equipment. OVP-modules type NCD 901 26 is half in size compared to earlier protection modules. Also has the protection levels been improved to secure operations on the RBS.OVP-TRM1 Transmission (E1/J1/T1) for 2 systems pair cable (100-120 ohm) OVP-TRM2 Transmission (E1/J1/T1) for 2 systems coaxial cable (75 ohm)

Product Number Length mm Width mm Height mm Weight kgsNCD 901 26/11 102 36 37 0.12NCD 901 26/12 102 36 37 0.12

58

POWER BACK-UP

Battery 2106IBattery 2106I 100AhBattery set for RBS 2016iUse the batteries as backup power for GSM RBS 2106 . The battery has a nominal output voltage of +24VDC and 100Ah.

Product Number Length mm Width mm Height mm Weight kgsBKC 901 06/037 380 210 390 70.50

Consists of:

Description QtyBattery 12V 2Battery Accessory kit 1

Battery 2106I 200AhBattery set for RBS 2016iUse the batteries as backup power for the GSM RBS 2106i. The battery has a nominal output voltage of +24VDC and 200Ah.


Consists of:


Battery 2106I 300AhBattery set for RBS 2016iUse the batteries as backup power for the GSM RBS 2106. The battery has a nominal output voltage of +24VDC and 300Ah.


Consists of:


Power Back-up

POWER BACK-UP

59

Battery 2106V3Battery 2106V3 100AhBattery Set for RBS 2106V3The batteries are to be used for the GSM RBS 2106V3 as backup power. The battery has a nominal output voltage of +24VDC and 100Ah.


Consists of:


Battery 2106V3 200AhBattery Set for RBS 2106V3The batteries are to be used for the GSM RBS 2106V3 as backup power. The battery has a nominal output voltage of +24VDC and 200Ah.


Consists of:


Battery 2106V3 300AhBattery Set for RBS 2106V3The batteries are to be used for the GSM RBS 2106V3 as backup power. The battery has a nominal output voltage of +24VDC and 300Ah.


Consists of:


Battery Accessory set, OtherSpare parts Accessory kits

Product Number Length mm Width mm Height mm Weight kgsBKY 901 13/16 450 405 75 1.00BKY 901 13/17 450 405 75 1.00BKY 901 13/18 450 405 75 1.00

60

POWER BACK-UP

ERICSSON NUMBER REGISTER

61

Numeric4/NTM 201 201/2 ..... 174/NTM 201 201/3 ..... 175/NTM 201 201/2 ..... 185/NTM 201 201/3 ..... 185/NTM 201 201/4 ..... 186/NTM 201 230/1 ..... 466/NTM 201 230/11 ... 486/NTM 201 230/12 ... 486/NTM 201 230/13 ... 476/NTM 201 230/14 ... 476/NTM 201 230/2 ..... 466/NTM 201 230/3 ..... 466/NTM 201 230/4 ..... 466/NTM 201 230/41 ... 566/NTM 201 230/42 ... 566/NTM 201 230/43 ... 566/NTM 201 230/44 ... 566/NTM 201 230/51 ... 566/NTM 201 230/52 ... 566/NTM 201 230/53 ... 566/NTM 201 230/54 ... 566/NTM 201 230/61 ... 566/NTM 201 230/62 ... 566/NTM 201 230/63 ... 566/NTM 201 230/64 ... 567/NTM 201 201 ........ 269/NTM 201 230/1 ..... 199/NTM 201 230/2 ..... 199/NTM 201 230/4 ..... 19

BBKC 901 06/034 ...... 59BKC 901 06/035 ...... 59BKC 901 06/036 ...... 59BKC 901 06/037 ...... 58BKC 901 06/038 ...... 58BKC 901 06/039 ...... 58BKY 901 13/16 ........ 59BKY 901 13/17 ........ 59BKY 901 13/18 ........ 59

FFAB 102 1044/01 .... 51FAB 102 1044/02 .... 51FAB 102 1044/04 .... 51FAB 102 1044/05 .... 51FAB 102 138/01 ...... 47FAB 102 1943/1 ...... 51FAB 102 1943/2 ...... 51FAB 102 1944/1 ...... 51FAB 102 579/01 ...... 45FAB 102 943/1 ........ 46FAB 102 989/1 ........ 51FAB 102 990/1 ........ 48

LLBP 112 102/1 .........31LDK 3016 .................40LPB 112 101/1 .........41LPK 102 024/3 .........41LPK 102 101/9 .........41LPK 102 107/1 .........41LSB 107 05/1 ...........40LSB 107 12/1 ...........36LSB 107 12/2 ...........36LSB 107 12/3 ...........36LSB 107 12/4 ...........36LSB 107 12/5 ...........36LSB 107 12/6 ...........36LSB 107 12/7 ...........36LSB 107 30/1 ...........40LSD 901 52/1 ...........40LSH 901 45/1 ...........38LSS 103 25/1 ...........35LSY 901 38/1 ...........38LSY 901 42/1 ...........38LSY 901 45/1 ...........40LSY 901 48/1 ...........38LTD 260 154/1 .........15LTD 260 154/1 .........40LTD 901 43/1 ...........40LTT 129 09/2 ...........39LTT 601 135/1 .........32LTT 601 136/1 .........40LTT 601 137/1 .........32LTT 601 140/1 .........35LTT 601 141/1 .........35LTT 601 142/1 .........44LTT 601 143/1 .........33LTT 601 143/2 .........34LTT 601 143/3 .........34LTT 601 145/1 .........35LTT 601 146/1 .........39LTT 601 147/1 .........39LTT 601 148/1 .........35LTT 601 150 ............33LTT 601 151/1 .........33LTT 601 152/1 .........11LTT 601 153/1 .........36LTT 601 154/1 .........31LTT 601 86 ..............37LTT 601 87 ..............37LTT 601 88 ..............37LTT 601 97/2 ...........44LTT 601 99/1 ...........37LYA 175 104/3 .........43LYA 175 107/1 .........44LYA 175 115/1 .........42LYA 175 117/1 .........42LYA 175 118/1 .........42LYA 175 119/1 .........42LYA 175 122/1 .........44

LYB 921 53/1 ........... 42LYB 921 53/2 ........... 42

MMPB 134 01/1 .......... 55MPB 134 02/1 .......... 55

NNBA 101 025/96 ...... 57NBA 101 22/1 .......... 57NBA 101 22/2 .......... 57NBA 101 22/3 .......... 57NBA 101 22/4 .......... 57NBA 101 22/5 .......... 57NCD 300 12/10 ........ 57NCD 300 12/11 ........ 57NCD 300 12/12 ........ 57NCD 300 12/13 ........ 57NCD 300 12/21 ........ 57NCD 300 12/22 ........ 57NCD 300 12/23 ........ 57NCD 901 26/11 ........ 57NCD 901 26/12 ........ 57NGT 901 09/1 .......... 45NGT 901 09/2 .......... 46NGT 901 09/3 .......... 47NGT 901 09/4 .......... 48NTM 101 1055/1 ...... 43NTM 201 1491/1 ...... 26NTM 201 207/1 ........ 55NTM 201 215/1 ........ 45NTM 201 215/2 ........ 45NTM 201 215/3 ........ 45NTM 201 215/4 ........ 45NTM 201 218/3 ........ 27NTM 201 218/5 ........ 28NTM 201 219/1 ........ 21NTM 201 2413/1 ...... 28NTM 201 2426 ......... 55NTM 201 257 ........... 27NTM 201 291 ........... 37NTM 201 2964/1 ...... 55NTM 201 2977/1 ...... 26NTM 201 2977/2 ...... 27NTM 201 2977/3 ...... 27NTM 201 3072/1 ...... 29NTM 201 3072/2 ...... 29NTM 201 3072/3 ...... 29NTM 201 3072/4 ...... 29NTM 201 3072/5 ...... 29NTM 201 3138/1 ........ 5NTM 201 3159/1 ........ 5NTM 201 3160/1 ........ 7NTM 201 3160/2 ........ 7NTM 201 3162/1 ...... 23NTM 201 3163/1 ...... 25NTM 201 3164/1 ...... 25

NTM 201 3167/1 ......25NTM 201 3211/1 ......15NTM 201 3211/2 ......15NTM 201 3216/1 ......14NTM 201 3326/1 ......19NTM 201 3335/1 ......20NTM 201 3416/1 ........6NTM 201 3416/2 ........6NTM 201 3416/3 ........6NTM 201 3425/1 ......18NTM 201 3426/1 ......18NTM 201 3444/1 ......27NTM 201 3446/1 ......28NTM 201 3448/1 ......12NTM 201 3448/2 ......12NTM 201 3448/3 ......13NTM 201 3449/1 ......13NTM 201 3449/2 ......13NTM 201 3449/3 ......13NTM 201 3469/1 ......10NTM 201 3477/1 ......28NTM 201 3477/2 ......28NTM 201 3477/3 ......29NTM 201 3477/4 ......29NTM 201 3477/5 ......29NTM 201 3494/1 ......19NTM 201 3501/1 ........4NTM 201 3502/1 ........4NTM 201 3604/2 ........9NTM 201 3605/1 ........9NTM 201 3606/1 ........4NTM 201 3607/1 ........9NTM 201 3655/1 ......16NTM 201 3656/1 ......16NTM 201 3656/2 ......16NTM 201 3657/1 ......21NTM 201 3657/2 ......21NTM 201 3727/1 ......30NTM 201 3728/1 ......30NTM 201 3729/1 ......30NTM 201 3730/1 ......30NTM 201 3745/1 ........7NTM 201 3767/1 ......30NTM 201 3767/2 ......30NTM 202 187/1 ........29NTM 202 188/1 ........23

RRNT 899 065/1 ........53RNT 899 033/1 .........47RNT 899 066/1 .........53RNT 899 067/1 .........53RNT 899 068/1 .........48RNT 899 94/1 ...........46RNT 980 02/1 ...........52RPT 403 179/01 .......53RPT 403 180/01 .......54

62

ERICSSON NUMBER REGISTER

RPT 403 181/01 .......54RPT 403 182/01 .......54RPT 403 183/01 .......54RPT 899 023/1 .........45RPT 899 024/1 .........53RPT 899 89/1 ...........54RPT 899 95/1 ...........53RPT 899 97/1 ...........53RPT 980 05/1 ...........52RPT 980 06/1 ...........52RPT 980 07/1 ...........52RPT 987 25/1 ...........53

SSET 145 064/230 .....27SET 145 064/305 .....27SET 145 095/457 .....27SMA 901 05/1 ..........22SNT 102 26 ..............21SXA 105 3055/2 .......56SXA 105 3055/4 .......56SXA 120 215/29 .......23SXA 120 216/40 .......23SXK 107 2022/1 .......24SXK 107 2023/1 .........8SXK 107 2024/1 .........9SXK 107 2025/1 .........9SXK 107 2126/1 .......23SXK 107 2144/1 .......23SXK 107 2146/1 .......24SXK 107 2146/2 .......24SXK 107 2150/1 .......25SXK 107 2157/1 .......24SXK 107 2158/1 .........8SXK 107 2158/2 .........8SXK 107 410/1 .........14SXK 107 411/1 .........15SXK 107 412/1 .........15SXK 107 413/1 .........10SXK 107 419/1 .........11SXK 107 420/1 .........11SXK 107 421/1 .........11SXK 107 422/1 .........11SXK 107 423/1 .........11SXK 107 424/1 .........22SXK 107 424/2 .........22SXK 107 5775/1 .......43SXK 107 761/1 ...........8SXK 107 761/2 ...........8

TTSR 951 101/01 .......50TSR 951 101/02 .......50TSR 951 101/03 .......50TSR 951 103/1 .........50TSR 951 103/2 .........50TSR 951 103/3 .........50

TSR 951 1193/1 ...... 50TSR 951 1193/2 ...... 50TSR 951 1193/3 ...... 50TSR 951 322/1 ........ 49TSR 951 322/2 ........ 49TSR 951 322/3 ........ 49TSR 951 70/1 .......... 49TSR 951 70/10 ........ 49TSR 951 70/2 .......... 49TSR 951 70/3 .......... 49TSR 951 70/5 .......... 49TSR 951 70/75 ........ 49

ZZTY 203 26/5, MN ... 41ZTY 203 26/6, ME ... 41ZTY 203 26/7, MS ... 41

E99 500 15 R

ev B

Head OfficeElektroskandia ABNorrvikenleden 97SE-191 83 SOLLENTUNAPhone + 46 8 92 35 00 [email protected] Fax + 46 8 92 39 90 www.elektroskandia.se

Date post:	29-Nov-2014
Category:	Documents
Upload:	heylaive-amany
View:	1,650 times
Download:	19 times

Site Materials 10(1)

Documents