1

(1) 70mm Tile Base Partition: Drg. No. - 1

Size- Tile of width-300,450,600mm, Tiles Ht-150,300,450,600,750mm & Thickness 70mm. Frame structure -are made by 1.6mm thk. MS CRCA sections and Structure are fabricated by MIG/TIG welding Machine. Tiles made by 12mm Thk. Prelaminated particle board. The tiles in Push fit. Tiles in PLB, Glass, Fabric and Steel have to be provided as per Architects design. Tiles are fitted PVC Dowel in PVC Bush with interference fit. Upper and side trim are 1mm thk. Aluminum extruded section snap fitting powder coated. End caps must be die cast Aluminum. All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. (2/3) COMPACTOR SINGLE BODY MOBILE/DOUBLE BODY Drg. No. – 2 Manufacturing, Supplying and fixing in place modular steel box type compactors size 2080(H) x900(W)x 450(D) mm of make as approved by Engineer-in-charge with following configuration and specification, consisting of Single Faced Fixed Drive, Single Faced Mobile Drive, Double Faced Mobile Drive as per layout requirement. consisting of Single Body, 2 Bodies, 3 Bodies, thickness of side sheet of body is 1 mm (CRCA grade-Il Steel), Back Thickness 0.80mm (CRCA grade-Il Steel), Shelf thickness 0.80 mm (CRCA grade-Il Steel), understructure sheet thickness 2.5mm. HR Steel, all steel components to be powder coated and baked at 200o Centigrade with 40-50 micron coating thickness. And all steel components shall be given 7 tank antirust phosphate treatments. Including the cost of Locks & Handles etc. complete

2

(4) Staff Workstation without Visitor Drg. No. - 3 Workstation without Visitor- Overall size:- (W)1490 x (D) 670mm. Providing & installing Work top 1350mm x 600mm. Modular Workstations with 1200mm height partitions supported on heavy duty levelers with two race ways one at skirting level and another above / below (As per requirement). The partition shall be of 70 mm thk work top 25mm thk PLPB post form. Worktop finished with laminate. The edges of worktop shall be finished with machine pressed matching imported or supreme quality PVC beading. The partition panels shall be made of PLPB/MDF. The partition panels above the worktops shall have combination of ceramic writing board and pinup board finished in fabric as approved/design and shall be fixed as per drawing. Slot for Switches and sockets of Power/Data/Voice etc. All the exposed partition paned edges shall be fixed with aluminum extrude box shape powder coated trims. Ends must be covered with Die cast aluminum. S.D.U. With Drawer- Size:-Height: 760mm, Width: 900mm, Depth: 400mm, Body Structure made of MS CRCA sheet 0.8mm thk. Sliding Door & Drawer made 0.8mm MSCRCA sheet. Top made of 18mm thick post form. Side Edges beading PVC 1/2mm thk .Drawer Chanel made of 1.25mmthk MSCRCA sheet with heavy duty delrine bearing. Drawer /Door lock Ebco/Doorset/ Hettic make lock. PVC/ Aluminum extruded handle with die cost bracket fitted in handle. All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

3

(5) SM/MGR/DM Table 1500x600x760Ht. with Side Runner + Key Board Tray + CPU Trolley Drg. No. - 4 Table Size:W-1500mm x D-600mm x H-760mm Top made of 25mm PLPB post formed and edge bend PVC 2mm thk. Side panel made of 18mm thk PLPB. Cable duct made of MS CRCA sheet. Side and front panel made of 18mm thk PLPB Board. Hardware Hettic/Ebco, Leveler Button-Type Nylon/PVC level-adjustor, S.D.U. With Drawer- Size:-Height: 760mm, Width: 900mm, Depth: 400mm, Body Structure made of MS CRCA sheet 0.8mm thk. Sliding Door & Drawer made 0.8mm MSCRCA sheet. Top made of 18mm thick PLPB post form. Side Edges beading PVC 1/2mm thk .Drawer Chanel made of 1.25mmthk MSCRCA sheet with heavy duty delrine bearing. Drawer /Door lock Ebco/Doorset/ Hettic make lock. PVC/ Aluminum extruded handle with die cost bracket fitted in handle. All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. (6) 1350X600 with side runner key board tray and CPU Trolley Drg. No. – 5 Table Size:W-1350mm x D-600mm x H-760mm Top made of 25mm PLPB post formed .edge bend pvc 2mm thk. Side panel made of 18mm thk PLPB. Cable duct made of MS CRCA sheet 0.8 mm thk. Vertical side and front panel made of 18mm thk PLPB Board. Hardware Hettic/Ebco, Leveler Button-Type Nylon/PVC level-adjustor S.D.U. With Drawer- Size:-Height: 760mm, Width: 900mm, Depth: 400mm, Body Structure made of MS CRCA sheet 0.8mm thk. Sliding Door & Drawer made 0.8mm MSCRCA sheet. Top made of 18mm thick postform. Side Edges beading PVC 1/2mm thk .Drawer Chanel made of 1.25mmthk MSCRCA sheet with heavy duty delrine bearing. Drawer /Door lock Ebco/Doorset/ Hettic make lock. PVC/ Aluminum extruded

4

handle with die cost bracket fitted in handle. All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. (7) Table 1050X600X760ht with Key board tray & CPU Trolley Drg. No. - 6 Table Size:W-1050mm x D-600mm x H-760mm Top made of 25mm PLPB post formed .edge bend pvc 2mm thk. Side panel made of 18mm thk PLPB. Cable duct made of MS CRCA sheet 0.8 mm thk. Vertical side and front panel made of 18mm thk PLPB Board. Hardware Hettic/Ebco, Leveler Button-Type Nylon/PVC level-adjustor Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

5

(8) Workstation 4 seater (single side) Drg. No. - 7 - Overall size:- (W)5150 x (D) 670mm. Providing & installing Work top 1200mm x 600mm. Modular Workstations with 1200mm height partitions supported on heavy duty levelers with two race ways one at skirting level and another above / below (As per requirement). The partition shall be of 70 mm thk work top 25mm thk PLPB post form. Worktop finished with laminate. The edges of worktop shall be finished with machine pressed matching imported or supreme quality PVC beading. The partition panels shall be made of PLPB/MDF. The partition panels above the worktops shall have combination of ceramic writing board and pinup board finished in fabric as approved/design and shall be fixed as per drawing. Slot for Switches and sockets of Power/Data/Voice etc. All the exposed partition paned edges shall be fixed with aluminum extrude box shape powder coated trims. Ends must be covered with Die cast aluminum. 3 Drawer Pedestal -Size: Height:640mm, Width:350mm, Depth:525mm Top made of 18mm thick PLPB Post Form. Side Edges covered by PVC beading, Drawer Body made-up of prime quality 0.8mm thk MS CRCA Sheet welded body Use MIG/TIG & Spot welding for fabrication, Front Drawer -Made of MS 0.8thk MS CRCA sheet & drawer Shell made of 0.6mm thk MSCRCA sheet. Channels are slide on delrin –bearings .Drawer lock Ebco / Doorset 6-lever cylinder rim lock. Casters are provided for free mobility. All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

6

(9) Workstation 3 Seater (Single Side) Drg. No. - 8 - Overall size:- (W)3880 x (D) 670mm. Providing & installing Work top 1200mm x 600mm. Modular Workstations with 1200mm height partitions supported on heavy duty levelers with two race ways one at skirting level and another above / below (As per requirement). The partition shall be of 70 mm thk work top 25mm thk PLPB post form. Worktop finished with laminate. The edges of worktop shall be finished with machine pressed matching imported or supreme quality PVC beading. The partition panels shall be made of PLPB/MDF. The partition panels above the worktops shall have combination of ceramic writing board and pinup board finished in fabric as approved/design and shall be fixed as per drawing. Slot for Switches and sockets of Power/Data/Voice etc. All the exposed partition paned edges shall be fixed with aluminum extrude box shape powder coated trims. Ends must be covered with Die cast aluminum. 3 Drawer Pedestal -Size: Height:640mm, Width:350mm, Depth:525mm Top made of 18mm thick PLPB Post Form. Side Edges covered by PVC beading, Drawer Body made-up of prime quality 0.8mm thk MS CRCA Sheet welded body Use MIG/TIG & Spot welding for fabrication, Front Drawer -Made of MS 0.8thk MS CRCA sheet & drawer Shell made of 0.6mm thk MSCRCA sheet. Channels are slide on delrin –bearings .Drawer lock Ebco / Doorset 6-lever cylinder rim lock. Casters are provided for free mobility. All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

7

(10) Workstation 4 seater (both side) Drg. No. - 9 - Overall size:- (W)2610 x (D) 1270mm. Providing & installing Work top 1200mm x 600mm. Modular Workstations with 1200mm height partitions supported on heavy duty levelers with two race ways one at skirting level and another above / below (As per requirement). The partition shall be of 70 mm thk work top 25mm thk PLPB post form. Worktop finished with laminate. The edges of worktop shall be finished with machine pressed matching imported or supreme quality PVC beading. The partition panels shall be made of PLPB/MDF. The partition panels above the worktops shall have combination of ceramic writing board and pinup board finished in fabric as approved/design and shall be fixed as per drawing. Slot for Switches and sockets of Power/Data/Voice etc. All the exposed partition paned edges shall be fixed with aluminum extrude box shape powder coated trims. Ends must be covered with Die cast aluminum. 3 Drawer Pedestal -Size: Height:640mm, Width:350mm, Depth:525mm Top made of 18mm thick PLPB Post Form. Side Edges covered by PVC beading, Drawer Body made-up of prime quality 0.8mm thk MS CRCA Sheet welded body Use MIG/TIG & Spot welding for fabrication, Front Drawer -Made of MS 0.8thk MS CRCA sheet & drawer Shell made of 0.6mm thk MSCRCA sheet. Channels are slide on delrin –bearings .Drawer lock Ebco / Doorset 6-lever cylinder rim lock. Casters are provided for free mobility. All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. Key Board Trey -Size:- Width:600mm, Depth:270 ,Height:70mm Made up of prime quality MS CRCA sheet 0.8mm thk. Tray Slide on ebco Telescopic Channel, The tray hanged below the top by steel MS brackets. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. CPU Trolley: Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

8

(11) Discussion Room /Meeting Room conference table Drg. No. - 10 Table Size:W-3300mm x D-1050mm x H-760mm & Both end round top 25mm thk made of membrane finish.Top made of 25mm PLPB post formed .edge bend pvc 2mm thk. Side panel made of 18mm thk PLPB. Cable duct made of MS CRCA sheet 0.8 mm thk. Vertical side and front panel made of 18mm thk PLPB Board. Hardware Hettic/Ebco, Leveler Button-Type Nylon/PVC level-adjustor (12) Round Table Dia 1200mm Drg. No. - 11 Size: Dia-W1200x750Ht 1. Top made up of 18mm thk membrane finish OR 12 mm thick clear glass with half round edge polish. 2. Frame Structure made up of Dia. 25x18g MS CR pipe with Powder coating / Crome Plating. 3. The overall appearance of the product shall be as per photograph.

9

(13) Round Table Dia 900mm Drg. No. - 12 Size: Dia-W 900x750Ht 1. Top made up of 18mm thk membrane finish OR 12 mm thick clear glass with half round edge polish. 2. Frame Structure made up of Dia. 25x18g MS CR pipe with Powder coating / Crome Plating. 3. The overall appearance of the product shall be as per photograph. (14) Sliding Door Unit-900 Wx400 D x1200Ht Drg. No. - 13 Size:- Height:1200mm,Width:900mm , Depth:400mm , Body Structure made of MS CRCA sheet 0.8mm thk. Sliding Door & Drawer made 0.8mm MSCRCA sheet. Top made of 18mm thick post form. Side Edges beading PVC 1/2mm thk .Drawer Chanel made of 1.25mmthk MSCRCA sheet with heavy duty delrine bearing. Drawer /Door lock Ebco/Doorset/ Hettic make lock. PVC/ Aluminum extruded handle with die cost bracket fitted in handle. All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface.

10

(15) ACEO/ACM/SGM Table Drg. No. -14 Size:- Table - 2100x900x760mm Ht. Side runner -1200x450x760mm Ht. Back Runner- 1650x450x760mm Ht. Corner unit - 450x450x760 mm Ht. 3Drawer Pedestal size- W-450mm D-540 Ht-650mm ACEO/ACM/SGM Table- made of BWR ply wood laminated with good quality 1mm thk laminate fitted with 25mm thk. MDF fascia duly deco painted. Door & drawer front made of PLBP. Hardware must be of Hettich /Ebco Company. Top of desk and cabinet made of 12mm thk glass. Product must be in compliance with drawing and as per architect instruction. Complete product must be knockdown type in construction. (16) GM/SM (CSC) Table Drg. No. - 15

Size:- Table - 1800x900x760mm Ht Side runner -900x400x760mm Ht. Back Runner- 1165x400x760mm Ht Corner unit- 635x635x760mm Ht. Table and side runner made of PLPB board and post formed particle board as per design requirement. All tops 25mm thick and sides 18mm thk. Hardware used must be of hettich/Ebco . Edge bend must be 2mm PVC on through feet edge bending m/c. Table must be made as per drawing and architects approval.

11

17 (ACEO/ACM/SGM/PA) Chair- Hi-back Sketch No. 16 Specification-Size-H:1070-1140mm, Seat ht: 420-490mm, D-700mm, W-600 mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is molded Bright Bar with stitched Mesh Cloth. Sturdy steel column gas lift for center support and seat height adjustment. Telescopic ABS cover over steel column. Five position Lockable Sincro tilt mechanism and with Single piece Die castes PP arm rest adjustable with PP pad. Quality tapestry. High density Molded PU cushion. Over all appearance of product as shown in picture. Upholstery 0.50 Mtr. 18. ( ACEO/ACM/SGM/PA ) Visitor chair-Low back Sketch No. 17 Size- H: 900-1000mm, Seat H: 425-525mm, D-575mm, W-550mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is glass filled Nylon fitted with Mesh Cloth. Sturdy steel column gas lift for center support and seat height adjustment. Telescopic ABS cover over steel column. Five position Lockable Sincro tilt mechanism and with Single piece Die castes PP arm rest adjustable with PU pad. Quality tapestry. High density Molded PU cushion. Over all appearance of product as shown in picture. Upholstery 0.85 Mtr.

12

19. (Mgr/DM) chair- Hi -back Sketch No. 18

Size: Total Height-1050-1150, Depth 650, Width-650 Seat Height:440-540. 5-Prong wide nylon base for stability, Telescopic ABS cover over Steel. Steel T-Nuts inserted in to ply for rigid fastening. Molded cushion seat & back, contoured for proper lumber support and rested back Adjustable and lockable tilting mechanism with adjustable knob. Upholstery 1.5 Mtr 20. Staff / Conference Chair - Low Back Sketch No. 19

Specification: Size:- H:-885-985,Seat h.-470-570, D:-650,W:-580 * 5- Prong, nylon- base for stability . Twin- wheel heavy-duty castors to provide easy mobility under static as well as dynamic load. Sturdy Steel- Column, carrying gas lift for seat height adjustment .The rare of back & seat covered with ABS cover. Hot press ply supported to cushion. Steel T-nuts inserted into ply for rigid fastening. Adjustable tilting mechanism with Knob. 0.70 Mtr.

13

21. Premium Hi Back (MD/CM) Sketch No. 20 Total Height: Min.1185mm Max.1265mm. Seat Height:Min.460 Max.540mm.Depth: 660mm. and width: 640mm. Material: Seat and back made up of 12mm thick hot pressed plywood, upholstered with black latherite with hi-density foam 50-55. The back foam is designed with contoured lumbar support for extra comfort. Foam thickness 60-100mm .The armrest one piece and made of black PP of virgin quality, cushion pad provided on arms as shown in photograph in letherite cloth. Castors: The twin wheel castors should be injected molded in black Nylon. Chair Base.: The pedestal should be injection molded in black 30% glass filled Nylon with gas lift mechanism. Finish: steel are to be powder coated after seven tanks anti corrosion pretreatment of surface. Coating thickness 50 micron, Available in Standard tapestry 22. Premium Low Back Sketch No. 21 Total Height: 1110-1130mm Seat Height:Min.460-Max.540mm.Depth: 650mm. and width: 640mm Material: Seat and back made up of 12mm thick hot pressed plywood, upholstered with black latherite with hi-density foam 50-55. The back foam is designed with contoured lumbar support for extra comfort. Foam thickness 60-100mm .The armrest one piece and made of black PP of virgin quality, cushion pad provided on arms as shown in photograph in letherite cloth. Castors: The twin wheel castors should be injected molded in black Nylon. Chair Base.: The pedestal should be injection molded in black 30% glass filled Nylon with gas lift mechanism. Finish: steel are to be powder coated after seven tanks anti corrosion pretreatment of surface. Coating thickness 50 micron, Available in Standard tapestry

14

23. Premium Visitor Chair Sketch No. 21-A

Specifications: Size: Height Overall/Seat - 1045/560mm, Depth - 660mm, Width- 640mm : Under Structure

canti lever type MS CRCA Tube 1.6 mm thick. Hot pressed ply wood with steel T-Nuts for rigid fastening.

Single piece die castes PP arm rest. Quality Latherite tapestry with double stitch. High density PU cushion.

All steel components should be epoxy powder coated followed by seven tanks anti corrosion treatment of

surface. The overall appearance of the product shall be as per photograph. Available in only Black Latherite. 24. GM/SM (CSC ) High Back Sketch No. 22 Size: Total Height-1030-1115mm, Depth 685mm, Width-590mm Seat Height:425-510mm. . 5-Prong wide nylon base for stability, Telescopic ABS cover over Steel. Steel T-Nuts inserted in to ply for rigid fastening. Molded cushion seat & back, contoured for proper lumber support and rested back Adjustable and lockable tilting mechanism with adjustable knob. Seat and Back Covered with ABS Cover. Upholstery 1.0 Mtr

15

25. GM/SM (CSC ) visitor chair-Low Back Sketch No. 23 Size: Total Height-810-895mm, Depth 685mm, Width-555mm Seat Height:425-510mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Hot pressed ply wood with steel T-Nuts for rigid fastening. Seat and back are covered with PP cover. Sturdy steel column gas lift for center support and seat height adjustment. Telescopic ABS cover over steel column. Lockable center tilt mechanism and with Single piece integral skin PU arm rest. Quality tapestry. High density Molded PU cushion. Over all appearance of product as shown in picture. Upholstery 1.2 Mtr. 26. Multi Purpose Rack Storage single Side Drg. No. - 24 Overall Size:- H:-1980mm,,W:-915mm D:535mm.* Body Structure: Side panel Made up of prime quality CRCA MS sheet 1.0mm thk Shelves Adjustable :Made up of prime quality MS CRCA sheet 1 mm thk, Shelf Partition :MS CRCA sheet 0.8mm thk. End cover: Made of MS CRCA sheet 0.8mm thk in different color shade. Finish: All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface.

16

27. Multi Purpose Rack Storage Both Side Drg. No. - 25 Overall Size:- H:-1980mm,,W:-915mm D:380mm.* Body Structure: Side panel Made up of prime quality CRCA MS sheet 1.0mm thk Shelves Adjustable :Made up of prime quality MS CRCA sheet 1 mm thk, Shelf Partition :MS CRCA sheet 0.8mm thk. End cover: Made of MS CRCA sheet 0.8mm thk in different color shade. Finish: All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface. (28) Key board Tray: Drg. No. - 26 Size:- Width:800mm, Depth:470mm,Height:70mm. Body Structure: Made up of point embossed (at 35mm pitch approx.) Prime quality CRCA MS sheet CR Steel sheet 0.8mm thk. Rolled on ebco Telescopic Channel, The tray hanged to the top by steel screw with brackets made up of Prime quality CRCA MS sheet 1.25mm thk. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

17

29. 3 Drawer Pedestal Drg.No. - 27 Size: Height:640mm, Width:350mm, Depth:525mm Top made of 18mm thick PLPB Post Form. Side Edges covered by PVC beading, Drawer Body made-up of prime quality 0.8mm thk MS CRCA Sheet welded body Use MIG/TIG & Spot welding for fabrication, Front Drawer -Made of MS 0.8thk MS CRCA sheet & drawer Shell made of 0.6mm thk MSCRCA sheet. Channels are slide on delrin –bearings .Drawer lock Ebco / Doorset 6-lever cylinder rim lock. Casters are provided for free mobility. All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface. (30) CPU Trolley: Drg. No. - 28 Size:- Width:180mm Depth:245mm,Hight:210mm Made up of press formed MS CR sheet Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

18

(31) Lab SDU with Top shelf : Drg. No. - 29 Size:-Length:1200mm, Width:- 760mm, Height:-1150mm, Storage depth is 560 mm & top overhang by 200mm at front. Body part made-up of prime quality CRCA Sheet Use only MIG/TIG & Spot welding for fabrication. Top made of 25mm post form. Side Edges covered with PVC edge band on edge bending machine. One adjustable shelve inside storage and PLPB Shelf above Work Top for keeping instruments. Locks Ebco / Doorset cylindrical, all steel components should be epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph. 32. Lab SDU Drg. No. - 30 Size:-Length:1200mm, Width:- 760mm, Height:-900mm, Storage depth is 560 mm & top overhang by 200mm at front. Body part made-up of prime quality CRCA Sheet Use only MIG/TIG & Spot welding for fabrication. Top made of 25mm thick postform . Side Edges covered with PVC edge band on edge bending machine. One adjustable shelve inside storage. Locks Ebco / Doorset cylindrical. All steel components should be epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

19

(33) Sofa straight line- 3 Seater Drg. No. - 31 Specification- Size-H-660 mm, L-1800 mm, D-735 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr (34) Sofa straight line- 2 Seater Drg. No. - 32 Specification- Size-H-660 mm, L-1200 mm, D-735 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr

(35) Sofa straight line- 1 Seater Drg. No. - 33

Specification- Size-H-660 mm, L-600 mm, D-735 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr

20

36.Lab Stool Drg. No. - 34 Specification: Size:H:1050, D:300 W- 450mm. Seat made of Molded Ply, upholstered with hard PVC upholstery, fitted on chrome plated steel stand as shown in photograph. 37. Confrance Low back Chair Sketch No. 35 Size: Total Height: 820-920mm, Depth:650mm, Width: 650mm Seat Height: 440-540mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Hot pressed ply wood with steel T-Nuts for rigid fastening. Sturdy steel column gas lift for center support and seat height adjustment. Telescopic ABS cover over steel column. Lockable center tilt mechanism and with Single piece integral skin PU arm rest. Quality tapestry with PVC beading all around. High density Molded PU cushion. Over all appearance of product as shown in picture. Upholstery 1.5 Mtr

21

38. SDU 1800mm H x 900mm W x 400mm D Drg. No. - 36 Specifications : Size:- Height:1800mm,Width:900mm, Depth: 400mm , Body Structure made of MS CRCA sheet 0.8mm thk. Sliding Door & Drawer made 0.8mm MSCRCA sheet. Top made of 18mm thick post form. Side Edges beading PVC 1/2mm thk .Drawer Chanel made of 1.25mmthk MSCRCA sheet with heavy duty delrine bearing. Drawer /Door lock Ebco/Doorset/ Hettic make lock. PVC/ Aluminum extruded handle with die cost bracket fitted in handle. All steel components should be epoxy powder coated followed by seven tanks anti corrosion pretreatment of surface. 39. PLPB Storage with PLPB Post Form Top: Drg. No. - 37 Specification: Storage made of PLPB board, sides 18mm, Self 25mm, back 12mm, Top Post Form board 25mm, edges sealed with PVC edge bends on through feed edge bending machine with hot melt glue. Hardware Hettic/Ebco, Good quality levelers at bottom. Overall design as per architect drawing.

22

(33) Delux Sofa - 3 Seater Drg. No. - 38 Specification- Size-H-870 mm, L-1975 mm, D-910 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr (34) Delux Sofa - 2 Seater Drg. No. - 39 Specification- Size-H-870 mm, L-1480 mm, D-910 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr

(35) Delux Sofa - 1 Seater Drg. No. - 40

Specification- Size-H-870 mm, L-965 mm, D-910 mm. Structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, Upholstered with premium quality PU cloth with help of stitching,. Overall appearance as per photograph Tapestry- Mtr

23

AIRCONDITIONING SYSTEM

These specifications pertain to all areas and general application of air conditioning.

Air Cooled Ductable Split Units: The Ductable unit shall be ceiling mounted type comprising of an indoor unit housing evaporator section and blower section in a single cabinet and an outside unit housing compressors, with condenser coil and fan.The AC should have two refrigent circuits . Casing: The casing shall be constructed of cold rolled steel, finished in polyester powder coat to provide resistance against corrosion. The discharge plenum, air conditioning and refrigeration compartment shall be insulated against heat and sound transmission. Bottom Panel: The bottom panels shall be held in place by concealed latches. Upper panel shall give access to blower and evaporator section. Every part shall be easily accessible for inspection, adjustment and service. Compressor: The compressor shall be, scroll type type compressor directly driven by motor. The motor and compressor assembly shall be sealed in one casing against dirt, moisture and air. The compressor shall be housed in the outdoor unit along with condenser & cooling fans. The motors shall be protected from overloads by motor winding thermostat and temperature controlled thermal element on the compressor. The compressor motor starter shall also be provided with overload protection and single phasing preventor. Unit should have microprocessor based control panel. The compressor shall be mounted vibration isolators. The compressor motor shall be designed to operator on 415 +/- 10% Volts 3- phase, AC supply. Air Cooled Condenser: The condenser shall be air-cooled type. It shall comprise of condenser coil and condenser fan, compressor and control panel only. This unit shall be suitable to be kept in the ambient location. Suitable arrangement shall be provided for the protection of the control panel. The coil shall be with copper tube and aluminium fins. The condenser shall be complete with axial type condenser fan with TEFC motor suitable for outside installation. Electrical connection shall be provided upto condensing unit by client. Evaporator Coil: The cooling coil shall be constructed of solid drawn copper primary tubes and assembled in steel frame. The tube shall be hydraulically expanded in the aluminum fins to ensure fight fin bond. The return bonds shall be die-formed and bronzed to the tubes and shall have thicker tube wall than the standard straight pipes. The tubes shall be of suitable thickness. Complete coil shall be tested with 325 psig nitrogen pressure. The drip pan under the entire coil section shall be rust protected, easily cleanable and drain protected by screen. Refrigerant flow to the cooling coil shall be controlled by thermostatic expansion valve/ capillary arrangement and a distributor. Blower: The blower shall be double inlet forward curved centrifugal fan having capacity to discharge large volume of air at lower noise level. Fan shall be statically and dynamically balanced for vibration-less operation. Fan shaft shall be mounted in permanently lubricated ball type rubber isolated bearings.

24

The fan drive should be preferably directly coupled with motor of required capacity having overload protection in starter. Refrigerant piping: The compressor, condenser and the evaporator coil shall be interconnected with copper refrigerant piping and the valves shall be of brass/gun metal. The refrigerant circuit shall include thermostatic expansion valve/ capillary arrangement, distributor, dehydrator and liquid line shut off valve. The refrigerant piping shall be of HARD TYPE of minimum 20G. The refrigerant piping shall be duly supported & clamped on walls / angle with as per site requirement. Pendant Type control: The Pendant type microprocessor based control shall be located at a convenient place in the conditioned area and shall be provided with an RTD sensor to control the room temperature accurately with +/- Deg. C of the set point and facility to display return air temperature of LED. The Control system should also provide auto-sequence starting with pre-determined time delay and also auto sequence stopping. The control system also provided anti- recycle timer for set delay between stopping and starting. Unit should have option for remote controlling . HP/LP cutout & interlocking: The compressor shall be protected with HP-LP cutout with manual reset. The starting of compressor motor shall be interlocked with blower motor & condenser fan motor. Filters: HDPE synthetic non-woven washable filter shall be provided for efficient filtration of all air before entering the evaporator coil. The filter shall have large surface area and dust holding capacity. Cassette / Hi Wall split ACs : Hi wall type split AC shall be supplied of approved makes only. The split AC should operate with R 22 gas. The AC should preferably have following features:

• Minimum 3 Star level rating by the Bureau of Energy Efficiency for its power efficiency for the SPLIT AC only .

• Anti-rust powder coated outdoor unit which would prevents the outdoor unit from rusting, even under harsh weather conditions.

• Should have Higher energy efficient rotary/scroll compressor so as to minimize the power consumption along with higher cooling efficiency and quiet operation.

• The unit shall be supplied with cord less LCD remote with large LCD display with basic functions like Cool/Fan/Dry/Auto mode, Sleep mode & On/Off Timer.

• The machine should have auto-restart function. In case of a power failure, the air conditioner should automatically restores the previous function settings.

Refrigerant piping (for split AC): The compressor, condenser and the evaporator coil shall be interconnected with soft copper refrigerant piping and the valves shall be of brass/gun metal. The refrigerant circuit shall include capillary arrangement & distributor. The refrigerant piping shall be of 22 G. The refrigerant piping shall be duly supported & clamped on walls / angle with as per site requirement. Sheet Metal Work:

25

Material: All ducts shall be fabricated out of best quality galvanized steel sheets. Sheets used shall be produced by hot dip process. All the ducting has to be checked for the leakage before insulation by visual inspection method in the presence of owner/ consultant. All the joints must have neoprene gasket to avoid air leakage. The thickness of the sheets shall be as given below:

Thickness of sheets in MM

Maximum size of Duct in MM G.S.S.

Up to 750 24 G

751 to 1500 22 G

1501 to 2250 20 G

2251 & above 18 G

The duct fabrication shall be carried out as per recommendation of IS- 655-1963 (or latest edition). All the transverse joints, connections, bracing, seams etc. shall be in accordance with the following tables:

Maximum size in MM Thickness of sheets (G.S.) in MM

Transverse joints Bracing

Upto 750 (24G) S-Slip on 2.5 H Centers Cross-break

751 to 1500 (22 G) GI Flange joint of 32mm connection on 2.5 m centers.

25x25x3 mm angles at 1.2 M from joints

1501 to 2250 (20 G) 40x40x5 mm angle connection on1 meter max. center with 35x3 mm bar reinforcing.

40x40x5mm angles at 60 cm from joints

2251 to above* (18) 50x50x5 mm angle connection on1 meter max. center with 35x3 mm bar reinforcing.

40x40x5mm angles at 60 cm from joints

Grills/Registers/Diffusers: All grills/Diffusers/Registers will be made form heavy gauge extruded Aluminum sections duly powder coated to match the interior requirements of Architect/Client. All the supply air grills/diffusers will be provided with opposed blade dampers fabricated from Aluminum. The damper should be suitable for operation from the front face of Grille/ Diffuser. Supply and return air registers: Supply and return air registers shall be of approved make with extruded Aluminum section finished with powder coating. The rectangular supply air grills shall be of fixed bars of 00, 150, or 300. The volume control damper shall be in aluminum with opposed blades. The rectangular return air grills shall be of fixed bar liner grills with 00, to 450 deflection. The return air shall be without VCD. The grills shall be provided concealed fixing arrangement. All the volume control dampers, the blank-off sheets and wherever any shining surface is visible behind the supply/return air grill should be painted with tow coats of black black-board paint.

26

Diffuser: All rectangular/square/round diffusers shall be of approved make with extruded Aluminum construction. The supply air diffuser shall be equipped with fixed air distribution grids and removable key-operated volume control dampers. All the diffuses shall be finished with powder coating approved color. The adjustable dampers shall be painted with black black-board paint. The return air diffusers shall be without VCD. All grill and diffusers shall be provided with sponge rubber gasket between flanges and the wall or coiling/bulkhead. All frame for fixing the grills and diffusers shall be provided by the building contractor, under the supervision of ducting contractor. However the grills and diffusers shall be fixed by the ducting contractor. Insulation: Under deck insulation (If applicable): Wherever indicated and specified in drawings, the exposed roof of the air-conditioned area and the plant room shall be covered with 50 mm thick expanded polystyrene. The expanded polystyrene shall be of TF quality. The E.P.S shall be stuck to the roof by tar after cleaning the same. Suitable supports of G.I. wire netting fixed in slab with screws shall be provided at a distance of 500 mm. Insulation of supply and return air duct: Insulation of supply air and return air ducts shall be done by 12 mm thick EPE layered polyethylene pre laminated with Aluminium foil. The insulation material shall be stuck to the duct surface by rubber solution after cleaning. All the joints have to be sealed properly with transparent / B.O.P.P. tape. Acoustic Insulation of supply air duct: Initial 1.5 m of supply air duct shall be lined by glass wool 12 mm thick of density 48 kg/cum covered with R P Tissue paper and finished with aluminum- perforated sheet. The plenum shall also be lined with this insulation. Electrical: Equipment wiring (wire/ cable sizes): For all single Phase/3 Phase wiring, 1100 Volts grade PVC insulated copper conductor cables shall be used. The minimum size of control wiring shall be 1.5 sq. mm. PVC insulated stranded soft drawn copper conductor wires drawn though conduit to be provided for connecting equipment and control panels. Power wiring shall be of the following sizes:

Motor Rating Power Cable Earthing

Upto 5 HP 3x2.5 sq mm Cu. 2 mm dia GI

6-7.5 HP 3x4 sq mm Cu. 3 mm dia GI

10-15 HP 3x6 sq mm Cu. 19 x 3 mm strip

20x25 HP 3x10 sq mm Cu. 25 x 3 mm strip

Guarantee : The period of guarantee shall be minimum 12 months from the date of commissioning.