RII Resources and Infrastructure IndustryRIIERR302D - Respond to local emergencies and incidentsAssessment Tools – Assessor Guide
Copyright SkillsDMC. All rights reserved
SkillsDMC (Resources and Infrastructure Industry Skills Council Ltd)
Tower 1, Level 1, Suite 2, 475 Victoria Avenue, Chatswood, NSW 2067
Telephone: +61 (02) 9324 8600
Facsimile: +61 (02) 9324 8699
Email: [email protected]
Web: www.skillsdmc.com.au
Published by: SkillsDMC (Resources and Infrastructure Industry Skills Council Ltd)
Tower 1, Level 1, Suite 2, 475 Victoria Avenue, Chatswood, NSW 2067 AUSTRALIA
First published: 2015
Disclaimer:SkillsDMC is the owner of all copyright and other intellectual property rights in the products and any modifications made by SkillsDMC to the materials (parent document issued to you at point of sale and as reflected in the invoice). You acknowledge that, apart from the limited licence granted under these Terms of Sale, you have no right, title or interest (including intellectual property rights) in the products. You will do anything reasonably required to give effect to SkillsDMC’s ownership of the products (parent document).
ContentsIntroduction..................................................................................................................................................... iv
Companion Volumes and Support Materials...............................................................................................iv
Assessor Guide................................................................................................................................................v
Contextualising the tools..............................................................................................................................v
Using the Assessment materials for RPL.....................................................................................................v
Steps in the RPL process............................................................................................................................vi
Overview of RPL process............................................................................................................................vi
1. Planning for Assessment............................................................................................................................vii
Set up for Practical Assessment.................................................................................................................vii
Set up for Theory Assessment...................................................................................................................vii
Preparation for Assessment.......................................................................................................................vii
Meeting with the Candidate.......................................................................................................................viii
2. Conducting the Assessment......................................................................................................................viii
Managing risk.............................................................................................................................................viii
Gathering and recording evidence during practical assessment...............................................................viii
Gathering supporting evidence....................................................................................................................ix
Workplace Health and Safety......................................................................................................................ix
3. Finalising the Assessment...........................................................................................................................x
Summary and sign-off..................................................................................................................................x
General Tips.................................................................................................................................................x
Suggested Methods of Assessment and marking guidance............................................................................1
RIIERR302D - Respond to local emergencies and incidents......................................................................1
Assessment Summary Cover Sheet................................................................................................................4
RIIERR302D - Respond to local emergencies and incidents......................................................................4
Candidate.....................................................................................................................................................4
Assessor......................................................................................................................................................4
Co-Assessor.................................................................................................................................................4
Pre-Assessment...........................................................................................................................................5
Assessment Summary.................................................................................................................................6
Re-assessment............................................................................................................................................7
2nd Re-assessment.......................................................................................................................................7
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page ii of xi
Assessment Method 1 – Direct Observation and Competency Conversation.................................................9
Assessment Method 1 – Direct Observation and Competency Conversation.............................................9
Assessment Method 1 – Observation and Competency Conversation......................................................10
Assessment Method 2 Theory - Questioning.............................................................................................12
Continue Assessment Method 2: Theory - Questioning............................................................................13
Continue Assessment Method 2: Theory - Questioning............................................................................14
Continue Assessment Method 2: Theory - Questioning............................................................................15
Continue Assessment Method 2: Theory - Questioning............................................................................16
Continue Assessment Method 2: Theory - Questioning............................................................................17
Continue Assessment Method 2: Theory - Questioning............................................................................18
Continue Assessment Method 2: Theory - Questioning............................................................................19
Continue Assessment Method 2: Theory - Questioning............................................................................20
Assessment Method 3 Supporting Evidence - Supervisor Testimony...........................................................21
Assessment Method 3: Supporting Evidence – complete where applicable..............................................21
Assessment Method 3 – Other Supporting Evidence....................................................................................22
Assessment Method 3: Supporting Evidence – complete where applicable..............................................22
Assessment Method 4 Workplace Portfolio (Project)....................................................................................23
Assessment Method 4: Workplace Portfolio (Project)................................................................................23
Additional Section............................................................................................................................................1
The Context of Assessment.............................................................................................................................1
Additional Items............................................................................................................................................2
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page iii of xi
IntroductionThis guide provides advice for an assessor on how to use the Resources and Infrastructure Industry Assessment Toolkit to manage the required assessment, or recognition of prior learning (RPL) process, for the relevant unit of competency. It provides general information on how to integrate the unit of competency performance criteria with the authentic workplace context to enable a candidate to be deemed competent for a particular stand-alone Unit of Competency, Skill Set or Qualification.
Companion Volumes and Support MaterialsSkillsDMC has developed a range of Companion Volumes to assist with implementation of the RII Resources and Infrastructure Industry Training Package. The Companion Volumes are non-endorsed components which provide implementation and assessment advice for RII Training package materials.. Development and maintenance of these Companion Volumes occurs through the SkillsDMC continuous improvement process.
Companion Volumes currently available on SkillsDMC website are:
Companion Volume Implementation Guide
provides an overview of the RII Resources and Infrastructure Industry Training Package including information about mapping, regulation and licencing, implementation, pathways advice and relevant links.
Companion Volume Foundation Skills
provides information about the core skill demands of learning, reading, writing, oral communication and numeracy in a unit of competency. It also offers advice on the development and assessment of Foundation Skills in the Resources and Infrastructure Industries and includes mapping of all Units of Competency to the Australian Core Skills Framework (ACSF).
Companion Volume Range of Conditions
contains the Range Statements for all Units of Competency. This volume has been broken up into ‘competency streams’ to simplify navigation.
The Companion Volume and Support Materials are located at www.skillsdmc.com.au
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page iv of xi
Assessor GuideThis Guide includes:
General Assessment Advice
An Introduction to the Guide and guidance on how to contextualise the tool for an assessment or use the materials for Recognition of Prior Learning (RPL) purposes.
Advice on Planning for the Assessment and Conducting and Finalising the Assessment.
Assessment Information and templates for this Unit
An outline of suggested Assessment Methods with corresponding marking information Assessment Summary Tool Practical and Theory Assessment Tools Supporting Evidence Tool
This Assessor Guide provides a framework for an assessor to manage the specific competency-based assessment for this unit. It combines the operational (workplace) context with the industry standard to provide a comprehensive assessment tool to ensure the Candidate has the opportunity to be deemed competent.
The assessor is to conduct the assessment within the boundaries of the Assessor Guide so all requirements of the unit can be met.
Contextualising the toolsBefore using the tools for any type of assessment, the documents must be read over by the assessor to ensure they are suitable for the context in which they are being used.
There is an “Additional Section” at the end of both the Assessor and Candidate Guide for contextualisation. This section provides scope for supplementary or replacement questions and the customisation of specific organisational policies, procedures or similar to be identified
Assessment tools may also be combined for multiple units, where units are combined for delivery. This involves combining the same types of tool (practical with practical, theory with theory) under headings that match the plan of delivery.
Using the Assessment materials for RPLThe assessment tools can be used for assessment after training has been delivered or for RPL purposes.
RPL is a process to recognise a person’s skills and knowledge, regardless of how they have been acquired. RPL assessments can cover part or whole units of competency. All employees interested in training should be made aware of what the RPL process is, and how RPL can be applied for, according to the organisation’s site policy.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page v of xi
Steps in the RPL processStep 1:
Candidate applies for RPL according to site policy
Step 2:
Initial interview and collection of documents
Step 3:
Conduct a competency conversation
Step 4:
Observe performance
Overview of RPL processThe steps in the RPL process are covered in the following diagram.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page vi of xi
1. Planning for AssessmentSet up for Practical Assessment Ensure date, time, place, Candidate, assessment instrument and any tools/equipment are arranged. Ensure the environment is adequate for verbal delivery of assessment. Clarify the timing of the assessment with the Area Supervisor or relevant person and any other work in
progress during this time. Determine contingency options if this access is interrupted. Gather relevant site standards and procedures from the appropriate authorised company personnel.
Set up for Theory Assessment Ensure date, time, place, Candidate, assessment instrument and any tools/equipment are arranged Ensure the environment is adequate for delivery of assessment, eg by computer, pen-and-paper or
orally Confirm the assessment questions have been drafted for easy conversion into a computer-based
questionnaire Check availability of support where English or computer literacy is an issue for the Candidate. Confirm the theory assessment has been drafted as a bank of assessment questions from which a
suitable set of sample questions can be chosen for any one assessment Check that when sample of assessment questions is chosen from the complete bank of items they
have been suitably selected (e.g. all areas of the job role have sufficient sample questions included; all sections of the assessment have representative questions included) Issues of question selection and coverage are decided according to site policy.
Ensure the assessment form is finalised for the Candidate to use (whether in computer, pen-and-paper or oral format).
Gather relevant site standards and procedures from the appropriate authorised company personnel.
Preparation for AssessmentItem Details ContingencyDate/Time
Location/Site
Equipment/tools
Other resources required
PPE required
Mode of communication
Special Requirements
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page vii of xi
Meeting with the Candidate Introduce yourself and verify the identity of Candidate Establish that learning has occurred and confirm the Candidate is prepared for the assessment Explain what is required of Candidate. Both Candidate and assessor must confirm Candidate’s
readiness for assessment. Discuss the process of the assessment and how a mix of questions and actions will be part of the
assessment process Advise the Candidate of performance requirements for “Satisfactory” performance, according to site
policy. Discuss your organisation’s approach to skills recognition (or RPL) and the procedure to apply for it Explain how evidence needs to be collected in a variety of ways Confirm the number of attempts to be given on any particular assessment item Indicate the Candidate’s rights in the appeals process if a conflict arises Indicate the link between the assessment and the corresponding unit of competency
2. Conducting the AssessmentSkills need to be applied in the workplace in a variety of circumstances. As such, assessors must ensure that the Candidate can competently and safely undertake the task/s being assessed in different situations and conditions. Sound assessment practice involves the assessor determining that candidates are able to demonstrate the required level of performance prescribed by the unit of competency consistently, over time, and in a range of workplace conditions/settings.
The requirement for performance to be demonstrated on more than one (1) occasion is intended
to drive the use of rigorous assessment practices. Assessment decisions based on a single observation of performance are not sufficient to make a valid or reliable determination of competency.
Managing risk Define the assessment work area and equipment to be used as part of the assessment. Check any safety requirements, such as the use of PPE, have been met. Explain the methods of communication and the signal to stop the assessment. Where the Candidate is working dangerously or without necessary care or confidence, the assessor
must direct the Candidate to cease work and terminate the assessment. Immediate feedback should be given.
Gathering and recording evidence during practical assessment Do not interrupt while the Candidate is performing a task. Ask “What if …” questions where possible to assess knowledge relating to emergency and/or operating
situations Keep instructions to specific actions and position yourself so not to hinder the Candidate but still be
able to observe all actions. Ask safety related questions prior to instructing the Candidate to act, in order to clarify his/her intent. Keep quiet through action steps to allow the Candidate to concentrate.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page viii of xi
Examine the selection of actions, degree of completion, and timing of outcomes of actions and record these on the instrument.
Check the Candidate’s actions with “what if…” questions to capture different dimensions of competency.
Summarise the assessment progress at the end of each section/element. Ensure that all assessment criteria are met before Candidate is granted overall competency on the
unit. All questions must be answered correctly unless otherwise stated in the assessment instrument or elsewhere in site policy.
Record results in the appropriate place within this document and add notes relating to specific occurrences that identify the individual assessment against the standard work processes.
Gathering supporting evidence The supporting evidence assessment can be undertaken at any stage. The assessment component covers various aspects of a Candidate’s job performance, workplace activities and previous experience and can inform the assessor of his/her competence against the unit of competency.
Not all methods of gathering supporting evidence need to be used for each element. The assessor should gather enough evidence to support a final decision on the Candidate’s competence, taking into account whether separate practical and theory assessments have also been undertaken.
Tick () the box as ‘Satisfactory’, if enough supporting evidence has been gathered for that particular element to form the view that the Candidate has demonstrated satisfactory performance overall. Cross (X) the box where there is not enough supporting evidence to show that the Candidate has achieved satisfactory performance against that particular element.
Workplace Health and Safety Ensure all personnel have completed an area-specific induction prior to assessment commencing. Site, area and statutory safety requirements must be observed at all times during the assessment. Personal Protective Equipment (PPE) appropriate to the task and the assessment context is to be worn
at all times
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page ix of xi
3. Finalising the AssessmentSummary and sign-off Make a final decision about the Candidate’s competence after completing the required assessment(s),
and provide feedback to the Candidate on their performance (highlighting both positive examples and room for improvement).
If the Not (Not Satisfactory) box is ticked, the assessor must inform the Candidate’s supervisor and further training needs to be given to bring the Candidate up to a satisfactory level.
Complete the final assessment summary sheet, including signatures of those involved, and explain that the Candidate is now responsible for maintaining their competence.
The Assessor will need to explain the re-assessment policy that applies to the Candidate in relation to gaining competence in this unit.
General Tips All assessment should be customised to reflect site-specific:
risks and hazards equipment and machinery processes and procedures, including reporting and recording procedures standards and requirements
All sections of the assessment must be completed with an ink pen. Pre–assessment: To ensure that the Candidate understands the assessment process the assessor
must explain the assessment and any appeal processes to the Candidate. Both are to sign the Pre-assessment form prior to commencing the assessment.
Performance will often need to be demonstrated over a period of time and/or in different locations. More than one assessment of a block of tasks may be necessary. The relevant part of a blank assessment tool can be copied for re-use, then dated and attached to the original once it is completed.
Where appropriate, performance should be assessed across different conditions e.g. wet and dry weather; day and night; different equipment attachments; different materials, etc.
The assessment tool is structured to allow for suitable breaks where needed between blocks of tasks. Outcomes from theory and other supporting evidence assessments should be reflected in the final
assessment summary. On final completion of the overall assessment the “Assessment Summary” sheet must be completed by
both the Candidate and Assessor. Communicate to the Candidate any feedback comments.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page x of xi
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
Page xi of xi
Assessment Tools for:RIIERR302D - Respond to local emergencies and incidents
Candidate Name:
SkillsDMC Issued May 2015 Assessor Guide <unit code>Review MAY 2016 Version 1
CandidateInitial:______
Page 12 of 2
Suggested Methods of Assessment and marking guidanceRIIERR302D - Respond to local emergencies and incidentsThe following information outlines the assessment items Candidates will be required to complete during each unit. For each separate assessment method there are acceptable responses recorded and parameters are set in which the assessment context is defined.
Note that some methods require the collection of a number of pieces of ‘evidence’ over a period of time. Other methods, such as the theory assessment, will take a more definitive amount of time.
Assessment Method 1Nature of task: Direct Observation and Competency Conversation
Location for assessment: Candidate Workplace
Supervision: Trainer/ Assessor
Commence Date: Complete Date:
Information:
1. Skills need to be applied in the workplace in a variety of circumstances. As such, assessors must ensure that the Candidate can competently and safely undertake the task/s being assessed in different situations and conditions, to industry standards. Sound assessment practice involves the assessor determining that the Candidate is able to demonstrate the required level of performance prescribed by the unit of competency consistently, over time, and in a range of workplace conditions or settings.
2. Assessors will evaluate the skills demonstrated by Candidates as specified in the Observation Checklist, (contained in this Assessor Guide).The Assessor will also conduct a competency conversation to determine and record Candidate competence. These questions guide your conversation with the Candidate and assist in your assessment of their competence. The notes you take about this conversation are important evidence for assessment.
3. The Assessor will provide feedback to the Candidate and record results appropriately.4. The Candidate will need to ascertain appropriate times and dates with Supervisors/ Managers and plan
for the assessment.5. Explain the elements of the observation (contained in this Assessor Guide) at the pre-assessment and
how the Candidate will be required to demonstrate competence at the observation.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 1 of 23
Assessment Method 2Nature of task: Theory / Questioning
Location for assessment: Workplace / Own time
Supervision: Trainer/ Assessor
Commence Date: Complete Date:
Information:
1. The questions pertaining to this assessment are included in the Candidate Guide.2. The questions and candidate answers are to be submitted to the Assessor as evidence of competency.3. Candidates are required to complete these questions in their own time to hand back to the Assessor at
the time of final summative assessment.4. The Assessor should provide feedback to the Candidate and record results appropriately on the
Marking Sheet provided (found within this Assessor Guide).
Assessment Method 3Nature of task: Supporting Evidence – Third Party (Supervisor Report)
Location for assessment: Workplace
Supervision: Supervisor
Commence Date: Complete Date:
Information:
1. The Third Party/ Supervisor Report is included in the Candidate Guide.2. Once completed by the workplace Supervisor, this report is to be extracted from the Candidate Guide
and submitted to the Assessor as evidence of competency.3. Candidates are required to have their Supervisor complete this report in the workplace to hand back to
the Assessor at the time of final summative assessment.4. The Assessor should provide feedback to Candidate and record results appropriately on the Marking
Sheet provided (found within this Assessor Guide).
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 2 of 23
Assessment Method 4Nature of task: Workplace Portfolio (Project)
Location for assessment: Workplace / Own time
Supervision: Trainer/Assessor
Commence Date: Complete Date:
Information:
1. Instructions pertaining to the workplace portfolio (Project) are included in the Candidate Guide.2. The pages reflecting the workplace portfolio (Project) results are to be extracted and submitted to the
Assessor as evidence of competency.3. Candidates are required to complete this project in their own time and to hand back to the Assessor at
the time of final summative assessment.4. The Assessor should provide feedback to the Candidate and record results appropriately on the
Marking Sheet provided (found within this Assessor Guide).
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 3 of 23
Assessment Summary Cover SheetRIIERR302D - Respond to local emergencies and incidents
Candidate AssessorCandidate name:
(Print)
Candidate comments:
Assessor name:
(Print)
Assessor comments:
Co-AssessorCo-Assessor Assessor name:
(Print)
Co-Assessor comments:
Candidate information
Any documentation provided as evidence must be prepared by you to a satisfactory standard and be in accordance with workplace/site policy and procedures, and industry standards.
If collecting material for an assessment portfolio, please ensure that the confidentiality of colleagues, workers and other persons is protected, and block out any sensitive information.
If you have any doubts regarding confidentiality and privacy issues, contact the organisation concerned.
(Signature)
(Date)
(Signature)
(Date)
Candidate Declaration: I declare that all work submitted for assessment has been completed by me, that all work has been attributed in the references provided for each item and that the intellectual property of authors is acknowledged.
Where work has been completed as part of a group activity, the work of each individual has been recognised.
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 4 of 23
Pre-AssessmentAssessment process explained to the Candidate ( if Yes).
Any appeal relating to the outcome of the assessment or the way in which the assessment was conducted shall be made through the company’s fair treatment policy as explained to the Candidate ( if Yes).
Candidate name:
(Print)
Candidate comments:
Assessor name:
(Print)
Assessor comments:
I fully understand the assessment and appeals process.
Assessment and appeals process has been explained to the Candidate.
(Signature)
(Date)
(Signature)
(Date)
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 5 of 23
Assessment SummaryCandidate Name
Date Submitted:
Unit Name & Code RIIERR302D - Respond to local emergencies and incidentsAssessment MethodsTick the box when an assessment method is completed
Overall Outcome ()Satisfactory Not Satisfactory
1.1. Direct Observation and Competency Conversation
1.2. Theory Assessment – Questioning
1.3.Supporting EvidenceNote: this report supports the assessment by the Assessor.
1.4. Workplace Portfolio (Project)
1st Assessment Overall Result for Unit of CompetencyCompetent Not Yet Competent
Re-submission/re-sitYes
What is required?
(Date)
Assessor
(name)
(Signature)
(Date)
Candidate
I have been provided with feedback on my performance for each assessment activity or task. I agree with the outcomes of my assessment for this unit of competency.
(Signature)
(Date)
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 6 of 23
Re-assessment
Re-assessment Overall Result for Unit of CompetencyCompetent Not Yet Competent
Assessor
(name)
(Signature)
(Date)
CandidateI have been provided with feedback on my performance for each assessment activity or task. I agree with the outcomes of my assessment for this unit of competency.
(Signature)
(Date)
Assessment MethodsTick the box when an assessment method is completed
Date:Overall Outcome ()Satisfactory Not Satisfactory
1.1. Direct Observation and Competency Conversation
1.2. Theory Assessment Questions
1.3.Supporting EvidenceNote: this report supports the assessment by the Assessor.
1.4. Workplace Assignment (Project)
2nd Re-assessment2nd Re-assessment Overall Result for Unit of Competency
Competent Not Yet Competent
Assessor
(name)
(Signature)
(Date)
CandidateI have been provided with feedback on my performance for each assessment activity or task. I agree with the outcomes of my assessment for this unit of competency.
(Signature)
(Date)
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 7 of 23
Assessment MethodsTick the box when an assessment method is completed
Date:Overall Outcome ()Satisfactory Not Satisfactory
1.1. Direct Observation and Competency Conversation
1.2. Theory Assessment Questions
1.3.Supporting EvidenceNote: this report supports the assessment by the Assessor.
1.4. Workplace Assignment (Project)
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 8 of 23
Assessment Method 1 – Direct Observation and Competency Conversation
Assessment Method 1 – Direct Observation and Competency Conversation
Candidate Name:
Assessor Name:
Workplace location:Site detailsNOTE: Where personal safety or environmental damage are limiting factors, assessment may occur in a simulated environment provided it is realistic and sufficiently rigorous to cover all aspects of this sector’s workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.During the assessment, the Candidate must ‘demonstrate knowledge’ in responding to local emergencies and incidents that safely, effectively and efficiently meets all of the required outcomes.
You will need to have a competency conversation to assess if the Candidate has the required knowledge for this unit.
Competency ConversationAsk where and how the organisational policy and procedures are used for the following:
statutory compliance site emergency and incident situations initial response First Aid accessing and interpreting geological and survey data using site communication systems using personal protective equipment understanding fire fighting techniques
Assessment ComponentSatisfactory
()
RIIERR302DKnowledge Evidence
Yes No
Candidate Feedback:Competency conversation comments:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 9 of 23
Assessment Method 1 – Observation and Competency Conversation
Candidate Name:
Assessor Name:
Workplace location:Site detailsNOTE: Where personal safety or environmental damage are limiting factors, assessment may occur in a simulated environment provided it is realistic and sufficiently rigorous to cover all aspects of this sector’s workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.During the assessment, the Candidate demonstrates completion of responding to local emergencies and incidents that safely, effectively and efficiently meets all of the required outcomes on more than one (1) occasion including:Ability to;
locates and applies relevant documentation, policies and procedures and techniques for the safe, effective and efficient completion of responding to local emergencies and incidents including:
identify hazards identify, analyse and report emergencies/incidents monitor and assess emergency situations assess situation and make decisions assess and manage risks
works effectively with others to undertake and complete the response to local emergencies and incidents that meets all the required outcomes including:
comply with written and verbal reporting requirements and procedures
communicate clearly and concisely with others to receive and clarify work instructions
communicating clearly and concisely with others to coordinate work activities
Assessment Component Satisfactory ()
RIIERR302DPerformance Evidence
Yes
No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 10 of 23
Ability to;
read and interpret site plans follow emergency evacuation procedures administer initial response First Aid select and use emergency equipment wear personal protective equipment apply fire fighting techniques isolate sources of danger, and placing as necessary;
signage/barriers/signals
Assessment Component Satisfactory ()
RIIERR302DPerformance Evidence
Yes
No
Candidate Feedback:Observation comments:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 11 of 23
Assessment Method 2 Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer the following questions:
Q1. Maintenance procedures for fire fighting equipment are best informed by:
A. WHS rules and regulationsB. environmental rules and regulationsC. manufacturer’s specificationsD. government legislation
A1. Answer C
Assessment Component Satisfactory ()
RIIERR302D1.1, 1.2.Performance Evidence
Yes No
Q3. A residual gas test after blasting indicates there had been a sulphur dust gas explosion. Follow-up processes might include:
A. reports to mining authorities and government agencies
B. washing down the faceC. dispersing inert dustD. decreased ventilation
A2. Answer A
RIIERR302D1.1, 1.2, 1.3, 1.6, 1.10, 2.3.Performance Evidence
Yes No
Q4. When confronted with the choice of putting out the fire or ensuring personal safety, the fire team member should choose putting out the fire.
True
False
A3. Answer False
RIIERR302D1.1, 1.3, 1.9.Knowledge Evidence Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 12 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q5. The breathable air produced by a self rescuer would usually last for:
A. 2 hoursB. 1 hourC. 30 minutesD. 10 minutes
A4. Answer C
RIIERR302D1.2, 1.7.Knowledge Evidence Performance Evidence
Yes No
Q6. Evacuation plans and maps for an underground mine would be found at:
A. the controls of the working equipmentB. the ventilation bratticeC. the working faceD. the crib
A5. Answer D
RIIERR302D1.1, 1.2.Knowledge Evidence Performance Evidence
Yes No
Q7. Which 3 items below constitute barriers to possible emergency incidents?
A. Standoff policies at the toe of a pit wallB. Barriers and signage around remote control
equipment working in a stopeC. Policies on classifications of dust levelsD. A check on emissions of a diesel engine working in
an underground mineE. Policies on mining sequences
A6. Answer A, B, C
RIIERR302D1.3, 2.3.Knowledge Evidence Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 13 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q8. Which of the following would be used to indicate H2S risks during drilling operations?
A. Readings from returnsB. Analysis of screeningsC. BOP readingsD. All of the above
A7. Answer D
RIIERR302D1.3.Knowledge Evidence Performance Evidence
Yes No
Q9. A near miss report at an open cut mine reveals that a haulage vehicle mounted a berm and crossed over into an a fall zone. What might the next course of action be?
A. Check the height of the berm to see if it is at least half the height of the wheels of the haulage vehicle
B. Check the height of the berm to see if it is at least twice the height of the wheels of the haulage vehicle
C. As there was no one injured and no damage done then the incident should be left without any response
D. s there was no injury or damage, then simply sack the driver and employ a better one
A8. Answer C
RIIERR302D1.3, 1.8, 1.9.Knowledge Evidence Performance Evidence
Yes No
Q10. A class C fire involving oxyacetylene tanks should be fought with _______________ and ______________ extinguishers.
A. dry powder, waterB. dry powder, CO2C. water, foam
A9. Answer B
RIIERR302D1.7, 1.8, 1.9, 2.4.Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 14 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q11. Notification of an emergency varies from site to site. Which of the following would be effective forms of notification?
A. Trigger pointsB. PAC. Two way radioD. All of the above
A10. Answer D
RIIERR302D1.5, 1.6, 1.10, 2.3, 2.7.Knowledge Evidence Performance Evidence
Yes No
Q12. When choosing a route in response to an emergency call what should responders first consider?
A. A route that has sealed roadsB. A route that is open to cross windsC. A route that allows for escapeD. A route that considers the quickest way to get there
A11. Answer C
RIIERR302D1.5, 2.3.Knowledge Evidence Performance Evidence
Yes No
Q13. Mustering prior to an evacuation from an off shore rig should also include:
A. assessments of health of those musteringB. roll call checksC. mustering points that consider the threatD. all of the above
A12. Answer D - all of the above
RIIERR302D2.1, 2.7.Knowledge Evidence Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 15 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q14. What must evacuation routes from an underground mine consider?
A. Mining sequencesB. Ventilation routesC. Shift changeoversD. Shift briefings
A13. Answer B
RIIERR302D2.1.Knowledge Evidence Performance Evidence
Yes No
Q15. An evacuation during a H2S event on a drilling rig involves consideration of the prevailing wind.
True
False
A14. Answer True
RIIERR302D2.1, 2.2.Knowledge Evidence Performance Evidence Yes No
Q16. A fire team’s initial response to a fire should be guided by P.A.C.T. This means:
A. Position, Acceleration, Control, TerminationB. Protect crew, Aquatic control, Clear fuel, Terminate
airC. Prioritising, Assessing, Choosing alternatives,
Taking actionD. Prioritising, Acting, Considering, Taking leave
A15. Answer C
RIIERR302D1.9, 2.1, 2.2.Knowledge Evidence Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 16 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q17. Order the following items in the event of discovery of a collapsed mine crew member.
A. Check the airwayB. Check for signs of circulationC. Check for immediate dangerD. Check for a response from the casualtyE. Check the breathing
A16. Answer C, D, A, E, B
RIIERR302DKnowledge Evidence Performance Evidence
Yes No
Q18. Flash over and draw back are best controlled in mines through:
A. water attackB. ventilation controlC. the use of vehiclesD. increasing ventilation flows through the mine
A17. Answer B
RIIERR302DPerformance EvidenceKnowledge Evidence
Yes No
Q19. What is the crucial PPE for gas inundation?
A. WHSB. HelmetsC. SCBAD. HAZCHEM
A18. Answer C
RIIERR302D1.4, 1.7, 1.9, 2.4.Performance EvidenceKnowledge Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 17 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q20. While conducting fire fighting operations it is important to use objects and PPE to avoid _______________ and ______________ heat.
A. conducted, radiatedB. convection, conductedC. radiated, fire induced
A19. Answer A
RIIERR302D1.4, 1.7, 2.4.Performance EvidenceKnowledge Evidence
Yes No
Q21. Diesel fume levels at a working face are increasing. What is the initial response?
A. Maintenance of the equipmentB. SCBAC. EvacuationD. Control through ventilation procedures
A20. Answer D
RIIERR302D1.9, 2.5.Performance EvidenceKnowledge Evidence
Yes No
Q22. A spillage of drilling fluids and caustic material on an off shore rig needs to be cleaned up and washed down. Which of the following will influence the procedure and disposal of waste?
A. Lands ActB. The Petroleum Submerged Lands ActC. Mining ActD. WHS rules and regulations
A21. Answer B
RIIERR302D1.1, 1.9, 2.5.Knowledge Evidence Performance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 18 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q23. A significant change in circumstance requiring immediate action in a pit would be floor heave or coal heave.
True
False
A22. Answer True
RIIERR302D2.5.Knowledge Evidence Performance Evidence
Yes No
Q24. During fire fighting activities a crew member inhales hot gases. What might be the next step?
A. Ensure crew member is OK and if they can still breath and want to continue fire fighting let them do so as this is classified as a minor burn
B. Let the crew member make their own way to safety as you continue fire fighting operations
C. Move the crew member under close supervision to safety as this is classified as a severe burn
D. Continue fire fighting and treat this minor problem later
A23. Answer C
RIIERR302D1.8, 1.9, 2.6.Knowledge Evidence Performance Evidence
Yes No
Q25. Fire control operations are best performed from:
A. areas that have resources for fire defenceB. areas that have evacuation routesC. structural features that are heat resistantD. all of the above
A24. Answer D - all of the above
RIIERR302D2.6, 2.8.Knowledge EvidencePerformance Evidence
Yes No
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 19 of 23
Continue Assessment Method 2: Theory - QuestioningCandidate Name:
Assessor Name:
During the assessment, did the Candidate adequately answer:
Assessment Component Satisfactory ()
Q26. Which 3 items below constitute control of fire areas after the initial incident has been controlled?
A. Leaving the fire during shift breaksB. Completing near miss reportsC. Raking down hot spotsD. Sealing off hot spots from oxygenE. Application of chemicals and inert substances to hot
spots
A25. Answer C, D, E
RIIERR302D2.8.Knowledge EvidencePerformance Evidence
Yes No
Feedback to Candidate:
Questioning comments:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 20 of 23
Assessment Method 3 Supporting Evidence - Supervisor Testimony
Assessment Method 3: Supporting Evidence – complete where applicable
Candidate Name:
Assessor Name:
Evidence is required to be collected that demonstrates a candidate’s competency in this unit. Evidence must be relevant to the roles within this sector’s work operations
Supervisor Testimony
Details:
Supervisor verification of Candidate performance
Assessment Component Satisfactory ()
RIIERR302DFoundation SkillsKnowledge EvidenceAnd / orPerformance Evidence
Yes No
Feedback to Candidate:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 21 of 23
Assessment Method 3 – Other Supporting Evidence
Assessment Method 3: Supporting Evidence – complete where applicable
Candidate Name:
Assessor Name:
Evidence is required to be collected that demonstrates a candidate’s competency in this unit. Evidence must be relevant to the roles within this sector’s work operations
During the assessment, the Candidate provided: Assessment ComponentMap to relevant assessment component
Satisfactory ()
Other 3rd party reportDetails:Other 3rd party verification of Candidate performance
Yes No
Induction / Employer Training Program(s)Details:Candidate has participated in Employer Induction / training program(s)
Yes No
Relevant licence / certificate / permitDetails:Relevant licences/certificates sighted and endorsed
Yes No
Work log book / Equipment use logDetails:Log book sighted and endorsed
Yes No
Training record bookDetails:Training record sighted and endorsed
Yes No
Feedback to Candidate:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 22 of 23
Assessment Method 4 Workplace Portfolio (Project)
Assessment Method 4: Workplace Portfolio (Project)Candidate Name:
Assessor Name:
During the assessment, did the candidate satisfactorily demonstrate the following
Explain a ‘local emergency and incident’ that you could be exposed to and would need to respond to at your site.
1. Detail the process you would follow to control the situation.
2. List the documentation that would support compliancy of your action
Some considerations that will need to be included: Assessment and monitoring of the situation
Communication with appropriate personnel
Controlling the emergency
Assessor guide
Some examples: site plans, Emergency / Mine plan, JSA, Safety audits, site fire / safety management strategies, contamination principles, issues register.Risks, hazards and environmental issues and control measures.
Policies and procedures: emergency evacuation proceduresSite emergency, hazardous goods, consequences of spills, Isolation, signage/barriers/signals - checklist. Risk matrix.The Petroleum Submerged Lands ActInitial response First Aid
Assessment Component Satisfactory ()
RIIERR302D1.1, 1.2, 1.3, 1.4, 1.5, 1.6, 1.7, 1.8, 1.9, 1.10.2.1, 2.2, 2.3, 2.4, 2.5, 2.6, 2.7, 2.8.Knowledge Evidence
Yes
No
Feedback to Candidate:Workplace project comments:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 23 of 23
Additional SectionThis section provides scope for you to add supplementary assessment items. It can be used to customise additional assessment methods and/or contextualised questions.
The Context of AssessmentThe RTO/Compliance Manager should take time to consult with the candidate’s site to determine the information that will complete the list below. Each of the assessment methods in this Guide should then be conducted using this list as a reference. This will help to ensure that the assessment process is consistent with the organisation’s/site’s work context.
Where assessment is being conducted in a simulated environment, the RTO should complete this page based on the documentation, policies, procedures and equipment that are used in the simulated environment. Further information about appropriate simulated assessment environments can be found in the SkillsDMC Companion Volume: Implementation Guide, available from www.skillsdmc.com.au.
The Assessor using this document should take time to familiarise themselves with the items in the list below. Where this is not possible, the Assessor should consider working with an Industry Subject Matter Expert from the organisation/site who is already familiar and experienced with the items listed.
Specific company policies that must be assessed against:
Specific company procedures (including work procedures) that must be assessed against:
Specific legislative/regulatory/statutory documentation that must be adhered to during the assessment:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Page 24 of 23
Additional ItemsCandidate Name:
Assessor Name:
Evidence
Satisfactory ()
Yes No
Feedback to Candidate:Workplace project comments:
Candidate Signature: Date:
Assessor Signature: Date:
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Section 2Page 25 of 3
RTO Name here
RTO ID Number here
SkillsDMC Issued July 2015 Assessor Guide RIIERR302DReview July 2016 Version 1
CandidateInitial:____________
Section 2Page 26 of 3