© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 1 - 9/25/2020
FEATURES
• Continuous lensing standard –runs up to 200’
• Extruded aluminum single piece housing
• 4’ and 8’ individual units, or continuous rows
• Straight runs with proprietary joiner design
• Efficacy up to 141 lm/W
• Soft diffuse direct lighting
• Textured powder coat finishes available in white,
black, silver and bronze
• Premium finishes also available
• Approved for dry and damp locations
• 0-10v dimming is standard
• Dim to 1% of output current is standard
LUMEN PACKAGES Based on 3500K CCT. Other CCT available.
DIMENSIONS
MODEL LUMENS INPUT WATTS Lm/W
SLIMD-8-500-35K 4,000 29 138
SLIMD-8-1000-35K 8,000 60 134
SLIMD - - - - -
SERIES - LENGTH - LUMENS PER FOOT - DISTRIBUTION - CCT (80+ CRI) - FINISH
SLIMD 4=4FT 350=350LPF SD=SatinIce Diffuse 30K=3000K PW=Powder Coat White PBR=Powder Coat Bronze
8=8FT 500=500LPF WD=Wide Diffuse 35K=3500K PB=Powder Coat Black PSFx=Premium Stock Finish (See Pg. 5)
XX=Run Length 750=750LPF WW=Wall Wash 40K=4000K PS=Powder Coat Silver PO=Powder Coat Other*
1000=1000LPF 50K=5000K
XXXX=Custom LPF TW=Tunable White1 *Factory to be supplied with RAL# or color chip
- - -
- MOUNTING** - VOLTAGE - OPTIONS
ACW05=Aircraft Cables w/ Canopy, White Cord 5’ U= 120v-277v CRI9050=Minimum 90 CRI (R9 50) DM=Daylight/Motion Sensor
ACW10=Aircraft Cables w/ Canopy, White Cord 10’ C= 347v #EM=Emergency Circuit #EMB6=6W EM Battery
ACB05 =Aircraft Cables w/ Canopy, Black Cord 5’ #EMB10=10W EM Battery #EMB15=15W EM Battery
ACB10 =Aircraft Cables w/ Canopy, Black Cord 10’ GTD=Generator Transfer Device PSRD=Philips Sensor Ready (DALI) Driver
ALW05= Aircraft Cables w/ Loop, White Cord 5’ PSTP=Philips Step Dimming Driver
ALW10= Aircraft Cables w/ Loop, White Cord 10’ DT1=eldoLED EcoDrive Dim to 1% (0-10V)
ALB05 = Aircraft Cables w/ Loop, Black Cord 5’ DTZ=eldoLED SoloDrive Dim to 0% (0-10V)
ALB10 = Aircraft Cables w/ Loop, Black Cord 10’ TW-EL=eldoLED DUALdrive Tunable White (DALI)1
SM=Surface Mount LDE1=Lutron Hi-Lume EcoSystem LED driver with Soft-on, Fade‑to‑Black dimming
AWM= Architectural Wall Mount PSQ02U=Lutron T-Series 1% 2-Channel Tunable White driver1
WM=Wall Mount VDO=Lutron Vive Integral fixture control (RF with daylight and occupancy sensing)
EXAMPLE: SLIMD-40-625-WD-35K-PW-ACW10-U-1EMB10
ORDERING LOGIC
1 Tunable White Driver must be specified in options
** See mounting details on page 2
2.0”
3.5”
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 2 - 9/25/2020
MOUNTING OPTIONS
ACxxx (Aircraft Cable with Canopy) - Drywall, Solid, Tile (On-Grid), Tile (Off-Grid)
AWM (Architectural Wall Mount) SM (Surface Mount) WM (Wall Mount)
ALxxx (Aircraft Cable with Loops)
STANDARD POWER LOCATION PLEASE CONSULT FACTORY FOR CUSTOM LOCATION
2”
2.48”
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 3 - 9/25/2020
ROW CONFIGURATIONS
Each starter fixture will be provided with (2) mounting supports. Each additional fixture will be provided with (1) support which can be
located anywhere along the 2nd half of the fixture (highlighted):
MOUNTING LOCATIONS
WIRING STANDARDS (Per NEC Requirements)
Each fixture will be manufactured with 300v,14ga AWG mains wiring.
Dependent on the length of the run, fixtures ordered with cords will be
provided with the following (based on 12w/ft):
Up to 160’ 18/3-22/2
Up to 160’ w/NL 18/4-22/2
Over 160’ 14/5
Over 160’ w/NL 14/6
*347V fixtures will be provided with 600V cables as required
The standard construction of run lengths is to build with as many 8’ sections as possible and finish the run with a shorter length fixture if
necessary. If a different configuration is needed to meet an aesthetic requirement, please indicate this on your P.O. when placing your
order.
Examples of the standard construction of runs over 8’ are as follows:
10' RUN 8 2
16' RUN 8 8
20' RUN 8 8 4
22' RUN 8 8 6
28' RUN 8 8 8 4
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 4 - 9/25/2020
JOINT CONFIGURATION
We provide joint configurations in X’s, T’s & L’s each available in the stock size of 24” X 24” as shown below. Please specify the joint configura-
tion and over all dimensions. Refer to dimension table below for example and available standard lengths.
Standard configuration of X, T and L configuration
EXAMPLES
Y
X
X
Y
X
Y
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 5 - 9/25/2020
X
Y
Y
X
X
Y
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 6 - 9/25/2020
PERFORMANCE
SLIMD-X-750-WD (80+ CRI)
SLIMD-X-750-SD (80+ CRI)
Model Lumens Watts LPW Model Lumens Watts LPW
SLIMD-4-750-WD-30K 3,000 24 122 SLIMD-8-750-WD-30K 6,000 46 130
SLIMD-4-750-WD-35K 3,000 24 125 SLIMD-8-750-WD-35K 6,000 45 133
SLIMD-4-750-WD-40K 3,000 23 128 SLIMD-8-750-WD-40K 6,000 44 136
SLIMD-4-750-WD-50K 3,000 22 133 SLIMD-8-750-WD-50K 6,000 43 141
Model Lumens Watts LPW Model Lumens Watts LPW
SLIMD-4-750-SD-30K 3,000 24 122 SLIMD-8-750-SD-30K 6,000 46 130
SLIMD-4-750-SD-35K 3,000 24 125 SLIMD-8-750-SD-35K 6,000 45 133
SLIMD-4-750-SD-40K 3,000 23 128 SLIMD-8-750-SD-40K 6,000 44 136
SLIMD-4-750-SD-50K 3,000 22 133 SLIMD-8-750-SD-50K 6,000 43 141
SLIMD-4-750-SD-35K
SLIMD-4-750-WD-35K
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 7 - 9/25/2020
FINISHES
PREMIUM STOCK FINISHES
PSF001 (WOOD#1) PSF002 (WOOD#2) PSF003 (WOOD#3)
PSF004 (WOOD#4) PSF005 (WOOD#5) PSF006 (WOOD#6)
PSF007 (STONE #1) PSF008 (STONE #2) PSF009 (METAL #1)
STANDARD FINISHES
NOTE: A minimal impact to lead times will apply to products specified with Premium Stock Finishes (PSF). It is not to
be assumed that these finishes are stocked in our warehouse, but rather, are readily available to us for your project.
All other custom finishes (PO) will incur a set up fee and will add an extended lead time to your project.
BLACK MINI TEXTURE WHITE MINI TEXTURE SILVER SPARKLE TEXTURE BRONZE SPARKLE TEXTURE
© 2020 StarTek Lighting America. All rights reserved. The information in this document is subject to change without notice.
1960 Swanson Ct, Unit C, Gurnee, IL 60031 • (877) STARTEK • [email protected] • www.starteklightingamerica.com
Slim Beam Direct
Type:
Project:
Page 8 - 9/25/2020
Housing
Nominal 2” x 3 1/2” square housing of continuous
extruded 6063 T5 aluminum.
Color Colors for the housing are available in a powder coat-
ed white, black, silver, bronze and woodgrain with
end cap to match. Consult factory for custom colors.
Luminaire Length 4' or 8' lengths are available for a single stand-alone
section. Using internal joiners, 4’ and 8’ sections can
be joined to form longer rows.
End Caps Injection molded flat end caps are mechanically
attached with no exposed fasteners to enhance ar-
chitectural aesthetic and prevent light leak
(woodgrain is standard in metal).
Source
Lumen packages are available in four color tem-
perature options (3000K, 3500K, 4000K and 5000K)
— all within 2.5 MacAdam ellipses.
Certification
Intertek cETLus Listed. RoHS (Restriction of
Hazardous Substances) and Buy American Act
compliant.
Battery Philips Bodine lithium ion battery providing up to
780lm(6W) or up to 1300lm(10W) for 90 minutes.
UL924 listed. Class 2 compliant. Meets Title 20 CEC
(California Energy Commission) efficiency stand-
ards.
SPECIFICATIONS
CONTROL
Sensor
Wattstopper FS-205 v2 Low Voltage PIR. Integrated photosensor for hold-
off daylighting control. 24VDC operating voltage. Adjustable time delay
(30 seconds to 30 minutes).
WARRANTY
COMPANION PRODUCTS
5-year limited warranty. Complete warranty terms can be located at:
http://www.starteklightingamerica.com/images/pdf/warranty/Beam_Series_Warranty.pdf
Note: Actual performance may differ as a result of installation environment and final application.
All values are design or typical values, measured under laboratory conditions, at 25°C (77°F) .
Environment
Suitable for dry and damp locations.
Operating temp.: -40°C to +50°C
-40°F to +122°F
Dimming Driver Universal Lighting Technologies (ULT) Everline
series of LED drivers allows tunable output currents
to achieve infinite configurations of output. UL
Class 2 recognized. 0-10v interface can be wired
as Class 1 or Class 2 circuit. Included 2.5Kw ring
and wave overcurrent protection, isolation of
each individual output and a fully potted driver
to protect from heat and vibration. Power factor
<.93
Packaging
Sustainably manufactured outside cardboard
box and biodegradable, protective poly-foam
luminaire inserts.
Slim Beam Direct/Indirect