SLJ Super Lift Jack Manual

7/28/2019 SLJ Super Lift Jack Manual

1/10

1

AME INTERNATIONAL WWW.AMEINTL.NET

A M E S U P E R L I F T J A C K S

INSTRUCTION MANUAL


2/10

2



INSTRUCTION MANUALSuperlift Jack Models

Model 100 -100 Ton Capacity

Model 125 -125 Ton CapacityModel 150 -150 Ton Capacity






Specifically designed for the mining industry, the AME SuperLift heavy-duty hydraulicjacks are the result of modern technology and are your best choice when servicing and

maintaining large off-road vehicles and equipment.

The AME SuperLift jack lifts from the lowest lift point of your vehicle. If necessary, thecylinder extension will give you ample elevation to raise your vehicle from its highest

point. The total lifting procedure involves only one operator and can lift a 350 ton truck

in minutes.

Trouble free and safe, AME SuperLift Jacks operate on the universally acceptedelectric/hydraulic or air/hydraulic systems.

The AME SuperLift jack will operate from the standard 90 160 psi shop air supply orthe electric power, to suite your power specifications.

AME SuperLift Jacks are fitted with 16 or 18 diameter tires on tapered roller bearingsand are power driven, so that accurate positioning can be achieved quickly and safely.

AME SuperLift jacks continue to prove themselves around the world and have becomerecognized as a safe, reliable lifting device.

NOTES REGARDING MANUAL

This manual is not intended to teach basic principles of hydraulics and although someexplanations of functions are given, a certain level of expertise on the part of the reader

is assumed. This manual is intended to help explain the operation of the system in and

easy-to-understand language. It should prove useful for personal to aid in trouble

shooting.


3/10

3



INSTRUCTION MANUALWarranty Clauses

Jacks sold by AME International warrants the jacks to be free from defects in materialand workmanship for a period of six (6) months from the date of sale. This warranty isexclusive in lieu of all other warranties, whether written, or oral.

AME International warranty shall be limited to repair or exchange, FOB the factory,except when at the request of AME International, the buyer shall make the units

available for inspection by AME International personnel at a place designated by AME

International in such a request.

Units repaired under this warranty and returned to the buyer shall be warranted for theremainder of the original warranty period.

When conditions are such that a warranty claim is refused, our written warrantyprovides that the unit be held for no more than thirty (30) days from the date of such

notification, pending disposition by you, the buyer in absence of any further instructions

from you, the unit will be returned to the original shipper (collect) and any liability by

AME International will be cease.

The above warranty does not cover conditions over which we have no control, includingbut not limited to, foreign materials in the fluid system, pressure and speed in excess of

published and recommend maximum, and products damaged, or subjected to accident

abuse, or misuse after shipment from the factory. Products altered or repaired by

anyone not authorized by AME International are not covered.

There will be no acceptance of any charges of labor and/or parts incidental to theremoval and remounting of products repaired or replaced under this warranty. AME

International will in no event be liable for any special or consequential damage or

penalties.


4/10

4



INSTRUCTION MANUALIndex

START-UP PROCEDURES ............................. 5

LIFTING PROCEDURES ................................ 6

MAINTENANCE PROCEDURES ............................ 7

TROUBLE SHOOTING ............................... 8-10

PARTS LIST ........................... 11-22

> Cylinder Replacement Parts

> Safety Block Replacement Parts

> Pump Parts

> Control Valve

> Miscellaneous Replacement Parts

MISCELLANEOUS INFORMATION ...................... 23-24

Page


5/10

5



INSTRUCTION MANUALStart-up Procedures

1. Please read the maintenance manual over carefully before proceeding with start-up ofthe system. In particular, familiarize yourself with the location of oil shut off valve and

the air inlet valve.

2. Visually check the equipment for any possible shipping damage. Should any evidence ofthis be detected, please report it immediately to your supervisor and/or

www.ameintl.net. Send photographs if possible.

3. Familiarize yourself with the controls of the jack.4. Remove the oil fill/vent; check the oil level, oil level should be easy to see. If oil cant be

seen, top off with AW32 hydraulic oil. Oil should be filled with jack in the closed

position.

5. Open oil supply valve, located next to the left tire (yellow handle).6. Attach air supply to the valve at the top of the jack near the handle. Important: keep the

line free of debris and no air lubricators.

7. Turn air valve to the ON position the pump will begin to operate.8. Move the lever to the up position, let the cylinder reach full stroke, then the pump will

slow down and sometimes stop pumping.

9. Move the lever down, and lower the cylinder into the closed position.10.Notice the water separators beside the right tire, drain daily.11.Before lifting refer to lifting procedures section.12.Change filter element 6-12 hours after start-up.

IMPORTANT

Warranties are not valid unless proper starting and maintenance

procedures are followed.

*NO AIR LINE LUBRICATORS WILL DAMAGE SEALS IN PUMP


6/10

6



INSTRUCTION MANUALLifting Procedures

Insure you have finished the start-up procedures. AME SuperLift jacks are designed to lift on a concrete surface. Move the jack under the lifting point of the equipment your lifting, the cylinder has a

removable end cap this can be removed and a SuperLift extension can be inserted to

achieve the proper starting point. (Extra extensions can be ordered to fit different

equipment). Use only original equipment extension for SAFETY due to the heavy loads.

Never lift without either end cap or extension in place.

Once the load is lifted turn OFF the air supply to the jack. The jacks are designed to be pumped up and down. All AME SuperLift jacks are designed with our patented Safety valve and will prevent the

jack from retracting due to hydraulic fluid loss.

Important: always use either the extension or the end cap on the jack or damage to thecylinder rod will occur.


7/10

7



INSTRUCTION MANUALMaintenance Procedures

DAILY

Make a visual walk-around to check for leaks and damage to hoses, fittings at the startof each shift.

Make sure the top of the cylinder is free of debris to insure proper fit of cap andextensions.

Familiarize yourself with the water separators beside the right tire, drain daily. Operate the jack forward and back also fully extend and retract the ram at the start of

each day. Check the chrome rod for damage.

MONTHLY Check the oil level in the down position (AW32 Hydraulic Oil). Check air pressure in tires (not foam filled tires). Check overall condition of jack. Inspect cylinder rod for damage. Lubricate chain drive. Insure the vented fill plug is venting (blow through it). Pressure wash.6 MONTHS

Filter changes every 6 months is recommended.YEARLY

Change oil annually or as environment dictates. FILTER CHANGES EVERY 6 MONTHS ISRECOMMENDED CHANGE OIL ANNUALLY AS ENVIRONMENT DICTATES.

NOTE: To ensure product safety and reliability, it is recommended that you repair or replace

any broken parts when found.


8/10

8



INSTRUCTION MANUALTrouble Shooting

JACK STARTS LIFTING BUT STOPS AND THE PUMP CONTINUES PUMPING

Check oil supply, valve in vertical, on position Check oil levelJACK WONT GO DOWN (RETRACT) AND PUMP IS WORKING FINE

Check oil supply valve in vertical, on position Check oil level

refer to locked load section

PUMP

Refer to pump section for symptoms and remedies


9/10

9



INSTRUCTION MANUALUnlocking a Loaded Jack

LOCKED LOAD

Is the pump working?

How is the oil level?

This procedure will unlock the

safety block

Tools Required

o 14 mm open end wrench

o 4 mm Allen Key

LOCKED LOAD REPAIR

#1. Locate the safety block. Its at

the base of the cylinder.


10/10

10



INSTRUCTION MANUALLocked Load Repair (continued)

#2. Locate the cartridge

on the side of the block aswell as the lock nut.

#3. Using the 14 mm open end

wrench loosen the lock nut ( turncounter clockwise).

Date post:	03-Apr-2018
Category:	Documents
Upload:	aula8045040
View:	244 times
Download:	3 times

SLJ Super Lift Jack Manual

Documents