Small things. Big difference. THE MAKERS OF PROTAPER ® | SPECTRUM ® |SANI-TIP ® | CAVITRON ™ |...

Small things. Big difference.

THE MAKERS OF

PROTAPER® | SPECTRUM® |SANI-TIP® | CAVITRON™ | ASH® INSTRUMENTS

Gutta coreTM

THE MAKERS OF


DENTSPLY• Serving dentists for nearly 200 years• 350 Research & Development Staff dedicated to

producing innovative products to improve the lives of dentists and patients

• 150,000 dental professionals educated worldwide every year through Dentsply education programme

• www.dentsplyacademy.co.uk for CPD• www.dentsplyreward.co.uk loyalty scheme

http://www.dentsplyacademy.co.uk/

http://www.dentsplyreward.co.uk/

THE MAKERS OF


THE MAKERS OF


3

crosslinked gutta-percha core obturator

….this filling method is easy to learn, is completely three-dimensional and can fill a root canal system in less than five seconds. Importantly and upon completion, there will not be a traditional plastic carrier left behind.www.endoruddle.com


THE MAKERS OF


THE MAKERS OF


4


• 3D obturation• Easy to create post-space• Easy retreatment• No plastic core• Easy to learn• Less time consuming• Short learning curve• Good blister, easy to use• Easy snap off of the handle • Appropriate to all canal anatomy

(long, curved, s-curved, narrow)

The 10 most often mentioned product benefits (market study 2011)

PRODUCT

THE MAKERS OF


THE MAKERS OF



5

Superior 3D obturation•The hydraulic force sends warm gutta-percha flowing equally in 3Dimensions•Centrally compacted gutta-percha creates predictable and consistent 3D fill that follows curves, finds accessories canals and flows into isthmus •GuttaCore offers a superior 3D fills with the ease of a single insertion•Placed in seconds

Ease of retreatment•No plastic core remaining in the root canal

Easy to create Post space•Fast & easy to create post space•The drill engage and remove the obturation material with unprecedented ease

Details

PRODUCT

Heated in seconds

Placed in seconds

Removed in seconds

THE MAKERS OF


THE MAKERS OF


6


Video

PRODUCT

THE MAKERS OF


THE MAKERS OF


7


Packaging

PRODUCT

PACK OF 5 BLISTERS

Ref A 1702 P

BLISTER ONLY

Ref A 1702 B

“P” for Pack “B” for Blister

THE MAKERS OF


THE MAKERS OF


8


Compatibility

PRODUCT

Always use the lowest heating level

THE MAKERS OF


THE MAKERS OF


9


OBTURATORBRAND STICKER OBTURATOR

SIZEHEATING POSITION

GUTTA CORE GUTTA CORE 20 to 90 20-90WAVE ONE WAVE ONE small

Primary / smallprimary

large large

PROTAPER PROTAPER F1F1-F2

F2F3

F3-F4-F5F4

F5

THERMAFIL -------- 20-25 20 - 25

30-35-40-45-50-55-60 30 – 60

70-80-90-100110-120-130-140 70 - 140

GT series X GT series X .04Size .04-.08.06

.08

.12 Size .10-.12

THE MAKERS OF


THE MAKERS OF



10

CLINICAL SEQUENCE

Please consult the Directions for Use for more comprehensive instructions and clinical techniques

Shape Verify Obturate• Check passivity by taking the size verifier to working length and confirm by rotating in the canal 180°.

• Use the size verifier as a finishing file to gently enlarge the canal terminus if necessary

• When the final shape is a .04 taper, select a GuttaCore™ Obturator package one size smaller than the last file taken to working length.

• When the final shape is a .06 taper, select a GuttaCore™ Obturator package of the same size as the last file taken to working length.

• Carefully follow the clinical sequence of your shaping system

1 2 3

PRECAUTIONS

• Select the GuttaCore™ Obturator according to the GuttaCore™ size verifier that fits the shaped canal passively.

• GuttaCore™ Obturator cores should not be used as size verifiers.

• Do not remove gutta-percha from the apical section of GuttaCore™ Obturator prior to filling the root canal space. Removing the gutta-percha may damage the obturator.

THE MAKERS OF


THE MAKERS OF


11


Step-by-step instructions to place a gutta•coreTM crosslinked Gutta-Percha Core obturator.Please consult the Directions for Use manual for more comprehensive instructions and clinical techniques.

Flare the canal coronally and ensure the gutta•coreTM obturator has sufficient space to enterthe root canal.

Use the gutta•coreTM size verifier to confirm the shape at working length and passive fit.a) If the fit is not passive, use the size verifier as a finishing file to gently enlarge the canalterminus or select a smaller size verifier.b) Irrigate with an antibacterial root canal cleanser according to product directions.c) Dry the canal thoroughly using absorbent points.d) Use a paper point of the same tip and taper as the last file taken to working length beforeheating the obturator.

Brush a very light coating of (AH Plus®) sealer throughout the coronal-apical canal system.To help ensure the obturator reaches working length, use an additional dry absorbent point toremove any excess sealer that may have accumulated on the canal walls or pooled in the apex.

Place the gutta•coreTM obturator in the gutta•coreTM oven (stopper must be under the holder)and set the working length.

a) Heat gutta•coreTM on the lowest heat setting. For all other obturators, select the appropriateheating level (20-90).b) When the obturator is ready (audible beep,flashing indicator light), remove it from the ovenand place the obturator smoothly, with one slow continuous motion, into the canal to the working

length.

Remove the handle from the gutta•coreTM obturator at the orifice by bending to either side ofthe canal wall. Alternatively, use a round bur.

CLINICAL SEQUENCE

THE MAKERS OF


THE MAKERS OF



12

GuttaCore™ Obturators

BLISTER5 obturators + 1 SV Product Ref

PACK25 obturators

(5 blisters, 5 SV)Product Ref

20 A 1702B 004 20 00 20 A 1702P 004 20 00

25 A 1702B 004 25 00 25 A 1702P 004 25 00

30 A 1702B 004 30 00 30 A 1702P 004 30 00

35 A 1702B 004 35 00 35 A 1702P 004 35 00

40 A 1702B 004 40 00 40 A 1702P 004 40 00

45 A 1702B 004 45 00 45 A 1702P 004 45 00

50 A 1702B 004 50 00 50 A 1702P 004 50 00

55 A 1702B 004 55 00 55 A 1702P 004 55 00

60 A 1702B 004 60 00 60 A 1702P 004 60 00

70 A 1702B 004 70 00 70 A 1702P 004 70 00

80 A 1702B 004 80 00 80 A 1702P 004 80 00

90 A 1702B 004 90 00 90 A 1702P 004 90 00

Gutta Core for ProTaper Next X2 A 1802B 004 25 00 Gutta Core for ProTaper Next X2 A 1802P 004 25 00Gutta Core for ProTaper Next X3 A 1802B 004 30 00 Gutta Core for ProTaper Next X3 A 1802P 004 30 00

Gutta Core for ProTaper Next X4 A 1802B 004 40 00 Gutta Core for ProTaper Next X4 A 1802P 004 40 00

Gutta Core for ProTaper Next X5 A 1802B 004 50 00 Gutta Core for ProTaper Next X5 A 1802P 004 50 00sv : size verifier / one in each blister

PRODUCT REFERENCES

PACK 5 BLISTERS

Ref A1702 P

BLISTER Ref A1702 B

Sizes : 20,25,30,35,40,45,50,55,60,70,80,90and Matching ProTaper NextTM Gutta Core

THE MAKERS OF


THE MAKERS OF


13


Final Shape.04 Taper

GuttaCore™ Obturators

Final Shape.06 Taper

GuttaCore™ Obturators WaveOne ProTaper

20/.04 - 20/.06 20 small F1

25/.04 20 25/.06 25 primary F2

30/.04 25 30/.06 30 F3

35/.04 30 35/.06 35

40/.04 35 40/.06 40 large F4

45/.04 40 45/.06 45

50/.04 45 50/.06 50 F5

55/.04 50 55/.06 55

60/.04 55 60/.06 60

70+/.04 60 70+/.06 70

80+/.04 70 80+/.06 80

90+/.04 80 90+/.06 90

When the final shape is a .04 taper, select a GuttaCore™ Obturator package one size smaller than the last file taken to working length.

When the final shape is a .06 taper or larger, select a GuttaCore™ package of the same size as the last file taken to working length.

THE MAKERS OF


THE MAKERS OF


14


CASE STUDY

Dr. Larry Farsakian

Dr. Jim Gutmann

Dr. Jim Gutmann

Mandibular left second molar with root lengths of 24.5 mm. Canals were prepared to a size F1 (ProTaper) and obturated with GuttaCore carriers and AH-Plus root canal sealer. Access to the placement of the carriers on the mesial was enhanced by removing the handle and using a locking forceps to enable the proper angle of delivery. The distal canal was obturated in the normal fashion with the handle in place.

CLINICAL EDUCATION

Clinical Case – Dr Gutmann- Dentistry Today The Future of Root Canal Obturation Written by James L. Gutmann, DDS, PhD Monday, 07 November 2011

THE MAKERS OF


THE MAKERS OF


15



• Superior 3D fills• Easy to create post-space• Easy retreatment

Date post:	03-Jan-2016
Category:	Documents
Upload:	sharyl-mosley
View:	213 times
Download:	0 times

Small things. Big difference. THE MAKERS OF PROTAPER ® | SPECTRUM ® |SANI-TIP ® | CAVITRON ™ |...

Documents