+ All Categories
Home > Documents > SmartROC T35 & T40

SmartROC T35 & T40

Date post: 21-Mar-2022
Category:
Upload: others
View: 17 times
Download: 0 times
Share this document with a friend
5
Surface drill rigs for quarrying and construction SmartROC T35 Hole diameter: 64–115 mm (2 ½”– 4 ½”) SmartROC T40 Hole diameter: 76–127 mm (3”–5”) SmartROC T35 & T40
Transcript
Page 1: SmartROC T35 & T40

Surface drill rigs for quarrying and construction

SmartROC T35 Hole diameter: 64–115 mm (2 ½”– 4 ½”)

SmartROC T40 Hole diameter: 76–127 mm (3”–5”)

SmartROCT35 & T40

Page 2: SmartROC T35 & T40

*SmartROC T40 drilled 100 meters in less than two hours (1 hour and 53 minutes) with excellent hole quality with 90 % hole straightness while only consuming 34.5 li-ters of fuel. This gave a fuel consumption

of 18.43 liters/hour and 0.35 liters/meter which is a solid indicator – SmartROC T40 can really perform under pressure.

Visit: http://mostfuelefficient.com

WORLD CHAMPION OF FUEL EFFICIENCYSmartROC T35 & T40 are the most fuel efficient drill rigs in the world. They show great performance even under the toughest drilling conditions.

MAIN BENEFITS

Combines low fuel consumption with high productivity

User-friendly display interface and improved ergonomics of the cabin

Easy to service and maintain thanks to low number of components

Built with the operator in mind, an ergo-nomic user interface makes drilling safer, faster and more effective. Not only are these rigs easier to operate and more pro-ductive, but they ensure the lowest cost per cubic meter produced by any compa-

rable rig in their hole range. We have put SmartROC T40 to test* and based on the result we have no doubt – SmartROC T40 does not compromize on productivity nor hole quality and truly is the world cham-pion of fuel efficiency.

2 3

Page 3: SmartROC T35 & T40

Metric Imperial

Filter area 11 m2 118 sq.ft

Number of filter elements 11 pcs 11 pcs

Suction capacity at 500 mm wg 560 l/s 1 200 cfm

Suction hose diam 127 mm 5’’

Cleaning air pressure, max 7.5 bar 109 psi

Cleaning air consumption 2– 4 l/pulse 0.06–0.12 cu.ft/pulse

DUST COLLECTOR DCT 200

+ FUEL EFFICIENCYThe entire system is designed to minimize energy losses. The operator

can adjust the flushing air volume and the dust collector fan speed ac-cording to need; so that both deliver only what is necessary for the best

performance. Engine and compressor speed are self-adjusting according to demand. Three variable hydraulic pumps help lower engine speed dur-ing none-drilling time and tramming. Further, an automatic cooler fan con-

trol is standard.

+ OPERATOR IN FOCUSThe value of technology is directly related to how easy it is to use. These rigs integrate advanced technology with operator ease-of-use and safety.

Inside the cleanly designed and comfortable cabin, the operator has full control over an efficient drilling cycle using two multifunction joysticks and an icon-based instrument panel. These rigs are equipped with an automatic

rod adding system, enabling them to drill preset hole depths without opera-tor interaction improving on consumables lifespan.

+ IMPROVED SERVICEABILITYCompared to similar rigs on the market, SmartROC T35 & T40 have 50%

less hoses and 70% less couplings reducing the risk of leakage. Hydraulic valves and electric modules are distributed and positioned at the location

where they function, allowing for easier access to components. Compared to previous generation rigs, the hydraulic tank is 65% smaller for more

space and easier service access. The machines have double hose drums on the feeder as standard.

EARN MOREPER CUBIC METERSmartROC rigs can be equipped with a hole navigation system (HNS) as an option, enabling drill pattern navigation via GNSS receivers. HNS manages hole position, incli-nation, correct aiming and the required hole depth as defined in the prepared drill plan. The result is a decrease in the drill and blast cost per cubic meter produced.

ATLAS COPCO SERVICEEven the best equipment requires regular service toensure optimal performance. Atlas Copco providesservice solutions to safeguard an optimized relationship between productivity, availability and operational cost. Atlas Copco Mining and Rock Excavation Technique has over 3 300 technicians located in over 80 countries. By combining the usage of Atlas Copco genuine parts with service provided by a certified Atlas Copco technician, you’ll have a winning combination no matter of where in the world you operate.

TECHNICAL SPECIFICATIONS

• Track frames with single grouser pads and cleaning holes • Hydraulic track oscillation and two speed traction• Atlas Copco screw type compressor• Operator’s cabin, ROPS and FOPS approved• LED work lights• Folding boom system• Aluminum profile feed beam• Hydraulic cylinder feed system• Carousel type rod handling system, 1 + 7 rods• Hydraulic rock drill• Dust collection system

Recommended hole range Drill rods Metric Imperial

SmartROC T35 T38, T45, T51 64–115 mm 2 ½”– 4 ½”

SmartROC T40 T45, T51 76–127 mm 3”–5”

Hydraulic rod handling system for max hole depth, with 3,6 m (12’ ) extension rods Drill rods Metric Imperial

SmartROC T35 T38, T45, T51 28 m 92’

SmartROC T40 T45, T51 28 m 92’

Anti-jamming, Feed speed control, Proportional control - feed RPCF, Proportional control impact DPCI

Hydraulic oil cooler Metric Imperial

Max ambient temperature 50°C 122°F

Pumps at 1800 rpm Metric Imperial

Axial piston pump (1) 145 l/min 38.3 US gal/min

Gear pump (2) 75 l/min 19.8 US gal/min

Gear pump (3) 50 l/min 13.2 US gal/min

Gear pump (4) 30 l/min 7.9 US gal/min

Gear pump (5) 40 l/min 10.6 US gal/min

Return and drainage filters Metric Imperial

Filtration rate 10 µm absolute

HYDRAULIC SYSTEM

Rock drill Drill rig Hole diameter Impact power Hydraulic pressure, max Impact rate, max Torque, max Weight approx

COP 1840+

SmartROC T35

64–115 mm 2 ½”–4 ½” 19 kW 25.5 hp 230 bar 3 335 psi 42–50 Hz 1180 Nm 870 lbf/ft175 kg 385 lb

COP 1840EX+ 230 kg 507 lb

COP 2540+64–89 mm 2 ½”–3 ½”

25 kW 33.5 hp 230 bar 3 335 psi 55–70 Hz 1180 Nm 870 lbf/ft 175 kg 385 lb

COP 2540EX+ 25 kW 33.5 hp 230 bar 3 335 psi 55–70 Hz 1180 Nm 870 lbf/ft 230 kg 507 lb

COP 2560+SmartROC T40 76–127 mm 3”–5” 25 kW 33.5 hp 230 bar 3 335 psi 44–53 Hz 1810 Nm 1 335 lbf/ft

187 kg 412 lb

COP 2560EX+ 249 kg 549 lb

• Dust pre separator• Double hose drum• Adjustable flushing air system• Air flow switch• Automatic cooler fan control• Adjustable dust collector fan speed• Double hydraulic drill steel support with movable down support• Service lamp inside canopy• Rock drill oil collecting system• Rubber skirt for DCT• COP Logic

MAIN COMPONENTS

HOLE RANGE

Hydraulic cylinder feed with hose guide and double drill steel support with movable lower guide/dust hood

Metric Imperial

Feed extension 1 400 mm 4’ 7’’

Feed rate, max 0.92 m/s 184 ft/min

Feed force, max 20 kN 4 400 lbf

Tractive pull, max 20 kN 4 400 lbf

SmartROC T35/ SmartROC T40 Metric Imperial

Total length 7 440 mm 24’ 5’’

Travel length 4 240 mm 14’

FEED COMPRESSOR

Atlas Copco OIS K-36-C111 GD, screw compressor, SmartROC T35 Metric Imperial

Working pressure, max 10.5 bar 152 psi

FAD, at normal working pressure 127 l/s 270 cfm

Atlas Copco OIS K-36-C111 GD, screw compressor, SmartROC T40 Metric Imperial

Working pressure, max 10.5 bar 152 psi

FAD, at normal working pressure 153 l/s 325 cfm

Metric Imperial

Hydraulic oil tank 100 l 26 US gal

Hydraulic system, total 160 l 42.7 US gal

Compressor oil 22 l 5.8 US gal

Diesel engine oil 16 l 4.2 US gal

Diesel engine, cooling water 43 l 11.3 US gal

Diesel engine fuel tank 370 l 98 US gal

Traction gear 3 l 0.8 US gal

Lubrication tank (ECL) 10 l 2.6 US gal

DEF fluid tank (Tier 4 Final only) 24 l 6 US gal

VOLUMES

Voltage 24 V

Batteries 2 x 12 V, 185 Ah

Alternator (Tier 3) 28 V, 80 Ah

Alternator (Tier 4 Final) 28 V, 105 Ah

Work lights LED type, front 4 x 3500 Lumen

Work lights LED type, rear 2 x 3500 Lumen

Work lights LED type, feed 2 x 5300 Lumen

Warning lamp and reverse buzzer

ELECTRICAL SYSTEM

HYDRAULIC ROCK DRILL

AIR CONDITIONER

Metric Imperial

Refrigerant R134a

Cooling capacity 5.5 kW

Fan suction capacity 125 l/s 265 cfm

ENGINE

Caterpillar turbo charged, diesel engine, CAT C7.1, 3/EU Stage IIIA and Tier 4 Final/EU stage IV and Add Blue Metric Imperial

Power rating at 2200 rpm 168 kW 225 hp

54

Page 4: SmartROC T35 & T40

X

4780

3100

L1

Hydraulic cylinder-feeding system ensures that the adjusted feed force is applied to the drill bit at all times during drilling, resulting in improved rock tool performance and productivity.

Double hose drums with a slot for each hose extends the life of the hoses and does not require greasing.

Hydraulic double drill steel support with movable lower support helps achieve straight holes and fast collaring.

LED lights offer better lighting, are more resistant to vibration, and easier to change.

• ROPS and FOPS approved with rubber vibration dampers • Rear view mirror• 2 x wipers with washer • Fire extinguisher, 6 kg (13 lbs) dry chemical type ABE class III type• Clear laminated glass (10 mm front and roof windows) • Outlet socket, 24 V• Clear laminated glass (8 mm side window) • Prepared with speakers for CD-radio or DVD radio• Clear toughened glass (8mm rear window) • Combined front mounted platform/tool box• Fully adjustable operator’s seat • Electric combined engine/inclination/hole depth instrument in main computer display• Cabin light • Electrical heated chair• Rig inclination indicator • Cab heating

SAFETY CABIN

Feed dumped 1 Metric Imperial

Height (H1) 3 200 mm 10’ 6’’

Length (L1) 11 600 mm 38’ 1’’

Feed dumped 2 Metric Imperial

Height (H2) 3 400 mm 11’ 2’’

Length (L2) 11 000 mm 36’ 1’’

Feed height Metric Imperial

Feed height (H) 7 440 mm 24’ 5”

HEIGHT AND LENGTH

Standard unit excluding all options and drill steel Metric Imperial

SmartROC T3515 100 kg (T3) 33 290 lb

15 300 kg (T4) 33 730 lb

SmartROC T4015 100 kg (T3) 33 290 lb

15 300 kg (T4) 33 730 Ib

Track shoe width (X) Metric Imperial

SmartROC T35 and T40 330 mm 1’ 1”

WEIGHT

Feed dumped 1 Feed dumped 2

Cabin• Window panes: Laminated 24 mm clear front, 10 mm roof and 8 mm tinted

side – toughend 8 mm rear• Tinted 10 mm roof window• Window wiper, right hand window• Sun shade kit (rear side, rear windows and roof)• Electric heated operator’s seat• Reverse camera with cab mounted display• Radio with CD player• Camera for support leg

Carrier• Hydraulic support leg• Hydraulic winch including wire with towing eye and wire guides• Diesel-driven engine heater• Electric fuel filling system• Tow hook• Track chains with triple grouser pads• LED side lights (points backwards towards the tracks)• Rubber disc for DCT• PAR Oil M & S• Central lubrication system• Air Anti Freezing System• Tool box left rear side• Extra air outlet on front of the carrier

Feed• Protective guard, according to EN16228 • Silencing kit • Bigger Dowel with big plate to avoid sinking in soft ground• TAC guide tube guides for drill steel support - TAC 64 mm for 64 mm guide tube - TAC 76 mm for 76 mm guide tube - TAC 87 mm for 87 mm guide tube

• Support bracket RHS carousel• Thread greasing devise ECG (with oil)• Thread greasing device, brush type (with grease)

Water system• Complete water mist system 120 l tank

Hole and inclination systems• Laser plane receiver for hole depth• GPS compass aiming unit• Automatic feed alignment

Hole Navigation System (HNS)• Hole Navigation System (HNS) Trimble or Leica receivers. Radio modem 450 or

900 MHZ. GSM modem. Sensors and ROC Manager software.

Automation & software• Measure While Drilling (MWD)• ROC Manager• Interface for 3 part HNS system

Parts and Services• COP Care• ROC Care

Optional equipment not mounted• Gas charging equipment for rock drill• First 50 hours service kit for compressor• Lubrication system• Conversion kit T45• Conversion kit T51• Measure While Drilling (MWD)• RCS service tool-box• Electrical tool kit

SELECTION OF OPTIONS

H1 H2

L2

24903030

Vertical reach (mm)Horizontal reach (mm)2 755

5 500

25°

25°

Feed with toe-hole kit

30°

95°

TECHNICAL SPECIFICATIONSTECHNICAL SPECIFICATIONS

SmartROC T35 & T40

33255043

H

6 7

Page 5: SmartROC T35 & T40

We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time.This is what we call – Sustainable Productivity.

98

51 3415 01e 2016

-08 Ö

rebro, Sw

eden. Legal Notice ©

Copyright 2013, A

tlas Copco R

ock Drills A

B, Ö

rebro, Sw

eden. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos m

ay show

equipment w

ith optional extras. No w

arranty is made regarding specifications or otherw

ise. Specifications and equipm

ent are subject to change without notice. C

onsult your Atlas C

opco Custom

er Center for specific inform

ation.

www.atlascopco.com

COMMITTED TO SUSTAINABLE PRODUCTIVITY


Recommended